DP8341N - Bipolar Decoder Receiver 24-DIP | National
Référence : DP8341N ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1 000 | $0 | $0,00 |
DP8341N Présentation
What is a decoder/receiver integrated circuit? A decoder/receiver is a specialized logic IC that accepts encoded or serial digital information and converts it into decoded control or data signals. It belongs to the broader logic IC and decoder/receiver hierarchy, sitting between a digital bus or communication line and the control logic of a microprocessor-based system. Such devices commonly support older bus architectures where signal direction, voltage levels, and timing must be translated into usable digital outputs.
The verified information establishes a bipolar 24-DIP package and decoder/receiver classification, but does not provide detailed electrical timing, supply-voltage, output-current, or pin-function data. Consequently, those values must be confirmed against the original manufacturer documentation before designing a new circuit or substituting the device. The package is a through-hole PDIP-24 format, making it suited to legacy controller cards, industrial control equipment, and repair or maintenance platforms that retain compatible sockets.
Typical design use includes legacy microprocessor interface boards, bus decoding, signal-conditioning subsystems, and industrial control systems built around older bipolar logic. Because the available records call the DP8341N a specialized decoder/receiver, system compatibility should be established from the original pinout, supply requirements, logic levels, and timing behavior. Those parameters are not present in the supplied verified data and are therefore not inferred here.
The DIP-24 package should be handled with standard electrostatic-discharge precautions and installed according to the original package orientation. Do not substitute a mechanically similar decoder solely by its DIP package count; verify every pin, voltage level, timing parameter, and power connection before substitution. This distinction is important because package compatibility alone does not establish functional compatibility.
This product page consolidates verified distributor listings, package identification, manufacturer identity, and sourcing context while explicitly separating unavailable technical details. It is intended to support initial sourcing and legacy-system investigation, with final electrical validation delegated to the original National Semiconductor datasheet or an authorized technical reference.
Alternatives de remplacement direct pour DP8341N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
[DATA_NEEDED: verified same-brand replacement MPN]
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
[DATA_NEEDED: verified cross-brand replacement MPN]
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
[DATA_NEEDED: verified cross-brand replacement MPN]
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
[DATA_NEEDED: verified cross-brand replacement MPN]
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
[DATA_NEEDED: verified cross-brand replacement MPN]
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DP8341N Valeurs maximales et caractéristiques électriques
| Product Type | Decoder, Receiver |
| Device Classification | Specialized IC |
| Logic Family | Bipolar |
| Boîtier | PDIP-24 |
| Nombre de broches | 24 pins |
| Type de montage | Through-hole |
| Manufacturer | National Semiconductor |
| Statut RoHS | Compliant |
| Statut du cycle de vie | Active |
Guide de configuration des broches du DP8341N pdip-24
Configuration des broches du DP8341N (boîtier pdip-24). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour DP8341N.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DP8341N convient pour 6 applications: Legacy Microprocessor Interface, Bus Decoding, Industrial Control Retrofit, Digital Signal Conditioning, Legacy Controller Repair, Vintage Digital Logic Systems.
Legacy Microprocessor Interface
The DP8341N is relevant to legacy microprocessor interface work because verified distributor records classify it as an MPU circuit and bipolar decoder/receiver. It may be used where an older controller needs decoded digital information before it reaches system logic. The PDIP-24 package supports through-hole retrofit or replacement work on legacy boards. Before installation, confirm the supply rail, logic thresholds, timing, and exact pin functions against the original National Semiconductor documentation; the supplied data does not provide those values, so the device should be treated as an uncharacterized legacy component until verified.
Recommandé
Bus Decoding
The decoder/receiver classification makes the DP8341N a candidate for examining in legacy digital-bus decoding circuits. Its role would be determined by the actual pinout, truth table, enable signals, and supply requirements rather than the package name alone. In a repair or redesign, compare the installed device with the original schematic and verify signal timing and voltage compatibility. The verified data contains no bus voltage, protocol, frequency, or propagation-delay specification, so those parameters must be obtained from the manufacturer document before the part is used as a timing-critical replacement.
Recommandé
Industrial Control Retrofit
A legacy industrial control cabinet may contain a DIP-24 decoder/receiver in a control, interlock, or interface section, making the DP8341N relevant for maintenance sourcing. The device's through-hole PDIP-24 format can simplify socket-level replacement if the footprint and pin count match, but mechanical fit is not enough: supply voltage, logic levels, timing, and pin functions must be compared. The verified records report active status and RoHS compliance, but they do not provide operating-temperature or environmental ratings. Confirm the original component documentation and board schematic before purchasing for production use.
Recommandé
Digital Signal Conditioning
The verified decoder/receiver category suggests a possible role in conditioning or interpreting digital signals inside older control logic. A practical repair engineer should identify the surrounding resistors, pull-ups, enable lines, and supply rails before ordering the DP8341N, because the provided web data does not define input thresholds or output drive capability. Use the original schematic to determine whether the circuit depends on bipolar logic levels, timing margins, or a particular active-high or active-low control convention. These details are essential for ensuring that a sourced replacement preserves system behavior.
Recommandé
Legacy Controller Repair
DP8341N availability is most clearly relevant to restoration of older controller boards where the original decoder/receiver is no longer readily sourced from the original manufacturer. The listed PDIP-24 package can be valuable for socketed or through-hole legacy assemblies, although the supplied results do not provide a manufacturer PDF or a verified alternate-source list. Before installation, inspect the board for socket damage and compare every connection on the original schematic. Also verify authenticity and condition with the seller, especially when purchasing an older bipolar integrated circuit.
Recommandé
Vintage Digital Logic Systems
The DP8341N may be evaluated for vintage digital-logic systems that use bipolar decoder/receiver functions and a 24-pin through-hole interface. This category includes educational, industrial, communications, and instrumentation platforms designed around older logic families. Compatibility is not established by the DIP-24 outline alone; the designer must verify pin numbering, supply voltage, input and output levels, enable polarity, timing, and thermal expectations. Since the supplied data does not include those specifications, the safest use case is a documented, board-specific repair after comparison with the original manufacturer documentation.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DP8341N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | [DATA_NEEDED: verified same-brand replacement MPN] | [DATA_NEEDED: verified cross-brand replacement MPN] | [DATA_NEEDED: verified cross-brand replacement MPN] |
|---|---|---|---|---|
| Package | PDIP-24 | PDIP-24 | PDIP-24 | PDIP-24 |
| Brand | National Semiconductor | National Semiconductor | Texas Instruments | onsemi |
Principaux différenciateurs
- Verified device classification (vs Generic 24-DIP decoder)
- Legacy through-hole integration (vs Surface-mount decoder/receiver)
- Documented distributor availability channels (vs Single-source component)
Notes de conception
Do not select a replacement based only on the PDIP-24 outline. Verify the original manufacturer pinout, supply voltage, logic thresholds, enable polarity, and timing against the board schematic. The verified web data identifies the DP8341N as a decoder/receiver but does not provide these electrical parameters, so a mechanically similar 24-DIP part may be functionally incompatible.
Preserve the original pin-1 orientation and socket footprint during any through-hole replacement. Confirm that no adjacent pins are shorted by socket debris, solder bridges, or contamination. Because the verified information does not include the pin assignments, inspect the board and schematic before applying power rather than relying on the package pin count alone.
Before inserting a sourced DP8341N, measure the board's actual supply voltage and identify which pins connect to the power rail. The supplied records do not specify the operating voltage or pinout. Use current-limited power when first testing a repaired legacy board, and compare input and output levels with the original system requirements.
Treat timing as a design constraint, not an assumption. Decoder/receiver devices can depend on propagation delay, enable timing, output loading, and the external pull-up or termination network. Since no timing or loading values are present in the verified data, reproduce the original circuit and compare signal behavior with a known-good board before finalizing a repair.
Informations de conformité
IC Online reports the DP8341N as RoHS compliant. No verified REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals data was supplied.
