EFM32G232F32G-E-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
Référence : EFM32G232F32G-E-QFP64 ✓ ActifEFM32G232F32G-E-QFP64 Présentation
A microcontroller is a programmable semiconductor that integrates a processor core, memory, I/O ports, timers, analog peripherals, and communication interfaces on one integrated circuit. The EFM32G family belongs to the ARM Cortex-M microcontroller hierarchy and is commonly used as the central control device in battery-powered sensors, industrial equipment, consumer products, and connected embedded systems. Its compact peripheral integration reduces the number of external components while supporting deterministic embedded control.
Key features include a 32-bit ARM Cortex-M3 core, 32 kB of Flash, 8 kB of RAM, 53 digital I/O pins, and three 16-bit timers. According to the Silicon Labs EFM32G data sheet, the family can consume as little as 0.6 µA in Stop mode and approximately 180 µA/MHz in Run mode. These figures make the device suitable for designs that spend substantial operating time in low-energy states while retaining the processing capability required for sensor processing, control logic, and communication handling.
The EFM32 architecture emphasizes fast wake-up behavior and energy-saving modes. Its integrated peripherals can perform timing, analog measurement, and communications-related tasks with reduced processor intervention, supporting low-power designs that use interrupts and autonomous operation instead of continuous polling. The 1.98 V to 3.8 V operating range also allows the microcontroller to operate from regulated 3.3 V systems, subject to voltage, temperature, and timing requirements for each peripheral.
Typical applications include battery-powered sensor nodes, industrial monitoring equipment, smart energy meters, building-control modules, and portable consumer devices. The 53 GPIO pins support multiple digital interfaces, while the three timers support motor, lighting, capture, or periodic timing functions. The 32 kB Flash partition also accommodates boot code, application firmware, and configuration data within a compact embedded design.
PCB implementation should preserve clean power distribution and decoupling close to the supply pins. Use the manufacturer’s pin-description table and reference layout when assigning tracks, programming debug connections, and routing sensitive analog or communication signals. Confirm the exact peripheral multiplexing and pin function before finalizing the board because the 64-pin package exposes a finite set of GPIO and alternate-function assignments.
This product page combines manufacturer specifications, same-footprint upgrade options, application guidance, and pin-compatible design considerations to support faster component selection, firmware planning, PCB layout, and sourcing decisions.
Alternatives de remplacement direct pour EFM32G232F32G-E-QFP64 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EFM32G232F32G-E-QFP64 (même facteur de forme et même empreinte) — différant par Package, Digital I/O Pins, Security Feature.
EFM32G232F64G-E-QFP64
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
EFM32G232F32-QFP64
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →EFM32G232F64-QFP64
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →EFM32G232F32G-E-QFP64 Valeurs maximales et caractéristiques électriques
| Product Type | 32-bit ARM Cortex-M3 Gecko microcontroller |
| Processor Core | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 kB |
| RAM | 8 kB |
| Digital I/O Pins | 53 pins |
| Timer Counters | 3 x 16-bit timers |
| Operating Voltage Range | 1.98 V to 3.8 V |
| Plage de température de fonctionnement | -40°C to +85°C |
| Stop Mode Current | 0.6 µA |
| Run Mode Current | 180 µA/MHz |
| ADC Resolution | 12-bit |
| DAC Resolution | 12-bit |
| Architecture | Single-core |
| Security Feature | AES |
| Boîtier | 64-TQFP, 10 mm x 10 mm |
| Type de montage | Surface mount |
| Statut RoHS | Compliant |
| Flash Program Memory Type | Built-in Flash |
Guide de configuration des broches du EFM32G232F32G-E-QFP64 64-tqfp, 10 mm x 10 mm
Configuration des broches du EFM32G232F32G-E-QFP64 (boîtier 64-tqfp, 10 mm x 10 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour EFM32G232F32G-E-QFP64.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
EFM32G232F32G-E-QFP64 convient pour 6 applications: Battery-Powered Sensor Node, Smart Energy Meter, Industrial Monitoring Controller, Building Control Module, Portable Consumer Device, Motor and Timing Control.
Battery-Powered Sensor Node
The EFM32G232F32G-E-QFP64 fits compact sensor nodes that periodically measure environmental or physical conditions and then return to a low-energy state. Its ARM Cortex-M3 core operates up to 32 MHz for local filtering and protocol handling, while the family’s Stop-mode consumption can reach 0.6 µA. The 53 GPIO pins support sensors, interrupt inputs, and external radios, although total system current will also include the sensor and communications hardware.
Recommandé
Smart Energy Meter
The EFM32G232F32G-E-QFP64 can serve as the control core in a smart energy-metering module where low standby power, timing accuracy, and multiple GPIO connections are important. Its three 16-bit timers support periodic measurement and output-control functions, while the 32 MHz Cortex-M3 core handles data conditioning and communications framing. A regulated 1.98 V to 3.8 V supply range supports compact meter electronics, but metering accuracy and safety isolation must be validated at the system level.
Recommandé
Industrial Monitoring Controller
The EFM32G232F32G-E-QFP64 is appropriate for industrial monitoring modules that combine digital sensors, status indicators, and serial communications. Its 53 digital I/O pins provide ample control and interrupt capacity, and the three 16-bit timers can support acquisition timing or control outputs. The single-core Cortex-M3 architecture simplifies firmware partitioning for low-power operation, while the 64-TQFP package keeps the design compact enough for DIN-rail or panel-mounted equipment.
Recommandé
Building Control Module
The EFM32G232F32G-E-QFP64 can control HVAC zones, lighting interfaces, occupancy inputs, and networked building equipment. Its 53 GPIO pins allow several sensors and discrete actuators to share one controller, and its 16-bit timers support repeatable timing functions. The 1.98 V to 3.8 V operating range integrates well with regulated building electronics, while Stop mode as low as 0.6 µA can reduce standby consumption when the module is inactive.
Recommandé
Portable Consumer Device
The EFM32G232F32G-E-QFP64 fits portable products that combine touch or sensor inputs, status LEDs, and a low-power serial radio. The Cortex-M3 core handles control logic at up to 32 MHz, while the EFM32G energy-saving modes reduce consumption during idle periods. Its 32 kB Flash and 8 kB RAM are suitable for compact firmware, and the 53 GPIO pins support multiple human-interface functions. Battery life should be calculated using the complete product duty cycle, including radio activity.
Recommandé
Motor and Timing Control
The EFM32G232F32G-E-QFP64 can coordinate timing-sensitive functions in small motor-control, valve-control, or actuator modules. Three 16-bit timers provide dedicated resources for pulse generation, input capture, or periodic control, while the 32 MHz Cortex-M3 core executes the application and supervisory logic. The 53 GPIO pins support position sensors, limit switches, and driver-enable signals. Precise current regulation, motor drive timing, and fault handling still require external power electronics and application-specific validation.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EFM32G232F32G-E-QFP64 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EFM32G232F64G-E-QFP64 | EFM32G232F32-QFP64 | EFM32G232F64-QFP64 |
|---|---|---|---|---|
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 kB | 64 kB | 32 kB | 64 kB |
| RAM | 8 kB | 16 kB | 8 kB | 16 kB |
| Digital I/O Pins | 53 pins | 53 pins | 53 pins | 53 pins |
| Timer Counters | 3 x 16-bit timers | 3 x 16-bit timers | 3 x 16-bit timers | 3 x 16-bit timers |
| Architecture | Single-core | Single-core | Single-core | Single-core |
Principaux différenciateurs
- Lower memory configuration within the same EFM32G232 family (vs EFM32G232F64G-E-QFP64)
- Same core speed and I/O count across the listed configurations (vs EFM32G232F32-QFP64)
- Compact 53-pin GPIO resource in a 10 mm square package (vs EFM32G232F64-QFP64)
Notes de conception
Follow the manufacturer reference layout for supply decoupling and place the required ceramic capacitors close to the device power pins. The EFM32G232F32G-E-QFP64 operates from 1.98 V to 3.8 V, so verify the regulator’s startup behavior, voltage tolerance, and sequencing against all operating conditions. For battery-powered systems, calculate average current from actual Run and Stop duty cycles rather than relying on a single mode current.
Use the manufacturer pin-description table to assign every signal on the 64-TQFP footprint. Keep SWD programming access available on the assembled board and route debug signals away from high-current switching nodes. Since the EFM32G offers 53 GPIO pins with alternate functions, review peripheral multiplexing before assigning a pin permanently; software changes cannot compensate for a PCB connection assigned to the wrong peripheral function.
Do not treat EFM32G232F32G-E-QFP64 as an exact substitute for the related F64G variant when memory size defines the firmware build. The F64G device doubles both Flash and RAM from 32 kB and 8 kB to 64 kB and 16 kB. Although the package is unchanged, validate startup behavior, linker configuration, bootloader assumptions, peripheral settings, and production programming before approving the substitution.
Keep clock, debug, and communications routes short and return them to a solid ground reference. Separate analog or sensor inputs from switching-power paths and other noisy digital nets, following the EFM32G reference layout for supported configurations. If the board combines the MCU with radio, relay, or motor circuitry, test clock jitter, ADC noise, and communication integrity with the final enclosure, connectors, and power-supply layout.
Informations de conformité
The component listing identifies the EFM32G232F32G-E-QFP64 as RoHS compliant. No separate REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement is included in the cited product information.