ESD1P0RFS - 1 pF 2-Channel RF ESD Diode | Infineon
Référence : ESD1P0RFS ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $0.282 | $0,28 |
| 10 | $0.282 | $2,82 |
| 100 | $0.282 | $28,20 |
| 500 | $0.282 | $141,00 |
| 1 000 | $0.282 | $282,00 |
ESD1P0RFS Présentation
What is an RF ESD protection diode? It is a transient-voltage-suppressor diode designed to divert electrostatic discharge energy away from a sensitive circuit while introducing very little capacitance into the protected signal. ESD1P0RFS is a low-capacitance, multi-line protection device, placing it in the interface-protection hierarchy between passive circuit protection and the protected RF or high-speed interface.
The principal feature is the 1 pF typical capacitance, which helps preserve signal integrity on RF and high-speed lines. The verified data identifies four RF ESD protection diodes in the six-terminal device and describes use for one protected signal line in an anti-parallel configuration. The application example also notes that a protected line may carry superimposed DC voltage up to ±2 × VF, where VF is the diode forward voltage.
Technically, the device combines low capacitance with high transient-energy handling. Its 2-channel arrangement allows two signal conductors or related interface lines to be protected in a compact footprint. The 70 V rating reported for the related distributor listing describes the device category and ordering context, while the verified series document supplies the application example and protection references.
Typical uses include RF antenna inputs, GPS, HDMI, Ethernet interfaces, communications equipment, and ultra-high-speed data-line protection. In these systems, capacitance affects edge bandwidth, insertion loss, and signal integrity; a 1 pF device is selected when the interface must remain responsive while exposed to ESD events.
PCB placement is important. Place the protection device close to the connector or board entry, connect the protected line through the device as shown in the manufacturer application example, and keep high-current surge paths away from sensitive logic. Verify the complete interface against the applicable system ESD, EFT, and surge requirements rather than relying only on the device rating.
This page consolidates the verified Infineon series documentation, distributor information, technical parameters, protection standards, and design considerations for faster component selection and PCB implementation.
Alternatives de remplacement direct pour ESD1P0RFS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ESD1P0RFS (même facteur de forme et même empreinte) — différant par Application Configuration, Device Type, Package, Surge Compliance.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ESD1P0RFW
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →ESD1P0RFS Valeurs maximales et caractéristiques électriques
| Device Type | RF ESD protection diode / transient voltage suppressor diode |
| Number of Channels | 2 channels |
| Number of Diodes | 4 diodes |
| Typical Capacitance | 1 pF |
| ESD Protection, Contact | ±20 kV |
| ESD Standard | IEC61000-4-2 |
| EFT Standard | IEC61000-4-4 |
| EFT Waveform | A, 5/50 ns |
| Surge Standard | IEC61000-4-5 |
| Surge Waveform | A, 8/20 µs |
| Surge Compliance | 10 A |
| Nombre de broches | 6 pins |
| Terminal Position | Dual |
| Terminal Form | Gull wing |
| Type de montage | Surface mount |
| Package Shape | Rectangular |
| Application Configuration | 1 protected signal line in low-capacitance anti-parallel configuration |
| Allowed Superimposed DC Voltage | Up to ±2 × VF |
| Manufacturer | Infineon Technologies AG |
Guide de configuration des broches du ESD1P0RFS rectangular
Configuration des broches du ESD1P0RFS (boîtier rectangular). Ce composant de puissance comporte des bornes de grille, de drain et de source. Pour les boîtiers non polarisés, consultez la fiche technique du fabricant pour l'orientation exacte de la broche 1 et les détails de l'empreinte. Les applications courantes incluent la conception d'alimentations, la commande de moteurs et la commutation de charges.
Aucune donnée de brochage détaillée disponible pour ESD1P0RFS.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ESD1P0RFS convient pour 6 applications: RF Antenna Input Protection, GPS and Navigation Interfaces, HDMI High-Speed Interface Protection, Ethernet Network Port Protection, Ultra-High-Speed Data-Line Protection, Communications Equipment ESD Protection.
RF Antenna Input Protection
The Infineon ESD1P0RFS fits RF antenna-entry protection because its 1 pF typical capacitance minimizes loading on high-frequency signal paths while providing ±20 kV contact ESD protection. Place the diode close to the antenna connector and route the protected conductor through the manufacturer’s anti-parallel arrangement. This helps protect the receiver or RF front end from electrostatic discharge without intentionally adding a large shunt capacitance. The design must still account for connector geometry, RF return paths, and the actual antenna frequency range.
Recommandé
GPS and Navigation Interfaces
ESD1P0RFS is appropriate for GPS or navigation signal protection where low capacitance helps preserve the protected line’s RF behavior. The verified Infineon documentation associates the ESD1P0RF family with GPS applications and specifies 1 pF typical capacitance. Position the protection device near the connector entry and use a controlled ground return so the transient current does not flow through sensitive receiver traces. Validate the complete interface for RF loss, ESD immunity, and system-level surge requirements.
Recommandé
HDMI High-Speed Interface Protection
The 1 pF typical capacitance of ESD1P0RFS makes it a candidate for ESD protection on suitable HDMI or other ultra-high-speed data lines. It helps limit parasitic loading while the device diverts ESD transients away from downstream logic. The correct channel assignment and connection must follow the six-terminal package drawing and the interface’s protection architecture. Because the verified data does not provide every pin-level connection or channel-bandwidth detail, engineers should confirm both with the current Infineon datasheet.
Recommandé
Ethernet Network Port Protection
ESD1P0RFS can be evaluated for Ethernet or other communications interfaces where low capacitance and transient protection are both important. The verified Infineon family page identifies Ethernet-related applications, and the target device provides 1 pF typical capacitance with ±20 kV contact ESD protection. Place the diode at the external interface boundary, maintain a short surge return, and verify line impedance and insertion loss after adding the protection path. A system-level qualification remains necessary.
Recommandé
Ultra-High-Speed Data-Line Protection
For ultra-high-speed data lines, ESD1P0RFS offers a compact, low-capacitance protection solution with 2-channel capability and 1 pF typical capacitance. The protection device should be close to the connector so the vulnerable PCB segment is minimized. Designers must balance capacitance, data-rate margin, return-path continuity, and the IEC61000-4-2, IEC61000-4-4, and IEC61000-4-5 test objectives. Use the manufacturer’s application example as the starting point, then validate with the finished board.
Recommandé
Communications Equipment ESD Protection
ESD1P0RFS is suited to communications equipment exposed to user contact or cable-transient ESD events. Its 1 pF typical capacitance is intended to preserve signal behavior in RF and high-speed interface sections, while the ±20 kV contact rating provides a defined device-level protection target. Integrate the diode close to the connector, provide a low-impedance return, and avoid routing transient current through sensitive analog or digital areas. The final device choice should be checked against the enclosure, grounding, and system test standard.
Recommandé
Données de référence d'ingénierie pour ESD1P0RFS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ESD1P0RFW |
|---|---|---|
| Package | 6-pin surface-mount gull-wing package | 6-pin surface-mount package; exact package designation requires datasheet confirmation |
| Brand | Infineon | Infineon |
| Channel Count | 2 channels | 1 channel |
| Typical Capacitance | 1 pF | 1 pF |
| Contact ESD Protection | ±20 kV | ±20 kV |
| Surge Compliance | 10 A | 10 A |
| Application Class | RF ESD protection diode | RF ESD protection diode |
| Protection Standards | IEC61000-4-2, IEC61000-4-4, IEC61000-4-5 | IEC61000-4-2 and related transient-protection family ratings |
Principaux différenciateurs
- Two-channel protection in one device (vs ESD1P0RFW)
- Matched low-capacitance RF protection (vs ESD1P0RFW)
- Defined transient-protection coverage (vs ESD1P0RFW)
Notes de conception
Place ESD1P0RFS at the interface boundary, immediately next to the external connector or cable entry. Route the protected signal through the device according to the Infineon application example and keep the ESD current return short and continuous. A long unprotected trace between the connector and diode leaves the downstream circuit exposed to the transient event.
Use the 1 pF typical capacitance as the initial signal-integrity selection value, then verify the complete interface with the actual connector, trace geometry, receiver impedance, and target data rate. Confirm insertion loss, edge-rate degradation, and return-path behavior on the finished PCB rather than assuming the device capacitance alone guarantees compliance.
Do not substitute ESD1P0RFW without checking channel count and PCB connectivity. The verified family data identifies ESD1P0RFS as 2-channel and ESD1P0RFW as 1-channel, even though both are described with approximately 1 pF capacitance and ±20 kV contact ESD protection. Also verify the six-terminal pin assignment from the official datasheet before fabrication.
Informations de conformité
The verified data references IEC61000-4-2, IEC61000-4-4, and IEC61000-4-5 transient-protection tests, but it does not state RoHS, REACH, lead-free, halogen-free, AEC-Q100, or conflict-minerals status.
