LM2902KDB - Quad 26V 1.2MHz Op Amp | Texas Instruments
Référence : LM2902KDB ✓ ActifLM2902KDB Présentation
An operational amplifier is a voltage-amplifying circuit whose open-loop gain is controlled by negative feedback. Operational amplifiers belong to the analog IC hierarchy and support precision control, signal conditioning, buffering, current-to-voltage conversion, and closed-loop circuit functions. The LM2902K combines four general-purpose amplifiers in one package, reducing component count and simplifying multi-channel analog boards.
Key characteristics include four amplifier channels, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 kV improved ESD protection, and an operating temperature range from -40°C to 125°C. Typical input offset voltage is 3 mV, typical input offset current is 2 nA, and typical supply-current drain is 0.8 mA. The common-mode input range includes ground, allowing the amplifier to process signals close to the lower supply rail.
The LM2902K belongs to the improved LM2902B generation. According to the Texas Instruments product documentation, the LM324B and LM2902B families can replace earlier LM224, LM324, and LM2902 versions while preserving the familiar quad-amplifier architecture. The B generation emphasizes improved electrical characteristics and stronger ESD protection compared with legacy devices.
Typical applications include industrial control and instrumentation, sensor signal conditioning, transducer amplification, low-frequency active filters, audio preamplification, buffer stages, and general-purpose analog interfaces. The internal frequency compensation supports straightforward closed-loop operation in amplifier, comparator, and follower configurations when operating within the device's common-mode and output-voltage limits.
The most important layout consideration is stable decoupling. Place a supply-bypass capacitor close to the positive and ground pins, maintain short return paths, and avoid long traces around high-impedance inputs. Verify output-current, input common-mode range, output swing, and ambient-temperature limits for each channel because the four amplifiers share package power and thermal constraints.
This product page combines the LM2902KDB operating characteristics, drop-in alternatives, application guidance, comparison parameters, and practical design notes in one engineering reference. Use the Texas Instruments LM2902K documentation as the controlling source for final electrical limits, pin assignments, ordering information, and PCB land patterns.
Alternatives de remplacement direct pour LM2902KDB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2902KDB (même facteur de forme et même empreinte) — différant par Package, Mounting Type, Number of Amplifier Channels, Operating Temperature Range.
LM2902BDB
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LM324BDB
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LM324KDB
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LM2902KDBG4
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LM2902KDG4
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LM2902KDB Valeurs maximales et caractéristiques électriques
| Number of Amplifier Channels | 4 channels |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1.2 MHz |
| ESD Protection | 2 kV improved ESD |
| Typical Input Offset Voltage | 3 mV |
| Typical Input Offset Current | 2 nA |
| Typical Supply-Current Drain | 0.8 mA |
| Common-Mode Input Range | Includes ground |
| Plage de température de fonctionnement | -40°C to +125°C |
| Boîtier | 14-pin SSOP (DB) |
| Package Width | 5.30 mm |
| Type de montage | Surface mount |
| Device Family | LM2902K improved LM2902B generation |
| Statut RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Unknown |
| Lead-Free Status | Unknown |
Guide de configuration des broches du LM2902KDB 5.30 mm
Configuration des broches du LM2902KDB (boîtier 5.30 mm). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour LM2902KDB.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
LM2902KDB convient pour 6 applications: Industrial Sensor Signal Conditioning, Transducer and Bridge Amplifier, Audio Preamplifier, Active Filters and Control Loops, Automotive Low-Speed Control Interface, General-Purpose Buffering and Amplification.
Industrial Sensor Signal Conditioning
The LM2902KDB suits low-frequency industrial sensor conditioning because it combines four channels in one 14-pin SSOP and provides a common-mode input range that includes ground. A 1.2 MHz gain-bandwidth product is appropriate for scaling signals from resistive bridges, position sensors, and resistive transducers without demanding high-speed precision. Typical input offset voltage of 3 mV and input offset current of 2 nA help define the achievable accuracy, although the actual error budget must also include source impedance, resistor tolerance, and sensor excitation drift. Place the amplifier in the feedback path with the sensor return connected to the circuit ground, and verify that the output remains inside the amplifier's output-swing limits at every operating condition.
Recommandé
Transducer and Bridge Amplifier
The LM2902KDB can provide differential or single-ended gain for resistive bridge transducers in measurement systems. Its 1.2 MHz gain-bandwidth product supports practical closed-loop bandwidths well below the unity-gain frequency, while the input common-mode range extending to ground simplifies circuits that sense small voltage changes near the lower rail. The four-channel arrangement allows excitation buffers, differential amplification, active filtering, and output buffering to share one package. Designers should confirm the maximum input bias current, output-voltage swing, noise performance, and common-mode limits for their particular gain and bridge impedance. Stable feedback components and short, guarded input traces are important when the sensor output is small relative to offset and noise.
Recommandé
Audio Preamplifier
LM2902KDB is appropriate for low-frequency audio preamplification, mixer, and buffering stages where a 1.2 MHz op-amp bandwidth is adequate. Four independent amplifiers in a single 14-pin SSOP can reduce board area for multi-channel consumer and industrial audio equipment. The amplifier's common-mode range includes ground, helping low-voltage audio signals remain within the usable input region, and its typical input offset voltage of 3 mV is a key factor when designing around low-level signals. Set the closed-loop gain with low-noise resistors and check output swing into the next stage. Headroom, distortion, frequency response, noise, and output-current capability remain design-dependent and should be confirmed from the manufacturer electrical tables.
Recommandé
Active Filters and Control Loops
The LM2902KDB can implement first- and second-order active filters, integrators, and low-frequency control-loop functions because each of its four amplifiers is internally frequency compensated. Its 1.2 MHz gain-bandwidth product gives sufficient loop bandwidth for many industrial monitoring and control applications, while the common-mode input range including ground simplifies signals centered around the lower rail. Component tolerances and the amplifier's actual gain-bandwidth, slew-rate, and noise behavior determine the achievable filter accuracy. Use stable resistor and capacitor arrangements, keep the feedback network compact, and avoid driving large capacitive loads without isolation. Four channels allow cascading stages or implementing several filters in parallel, reducing component count while preserving identical device characteristics.
Recommandé
Automotive Low-Speed Control Interface
The LM2902KDB can support low-speed automotive control, actuator-interface, and diagnostic signal-conditioning functions when the individual operating limits are acceptable. The four-channel 14-pin SSOP provides a compact implementation for multiple low-frequency analog channels, and the -40°C to 125°C operating range covers widely varying vehicle temperatures. Improved 2 kV ESD protection adds useful robustness for exposed connections. Automotive qualification status, transient immunity, noise behavior, and the complete electrical limits must be checked before production release. Keep sensitive inputs away from engine-control harnesses and high-current switching paths, use short ground returns, and include protection networks that do not distort the intended signal bandwidth.
Recommandé
General-Purpose Buffering and Amplification
The LM2902KDB is a practical choice for general-purpose buffering, gain adjustment, and impedance conversion in instruments, control boards, and consumer electronics. Four amplifiers in one package can replace several discrete devices while maintaining consistent behavior across channels. The 26 V supply rating accommodates higher-voltage analog systems, and the 1.2 MHz bandwidth is suitable for many low-frequency signals. The input common-mode range includes ground, which helps when buffering signals near the lower rail, while the typical 0.8 mA supply-current drain supports power-conscious designs when all four channels are active. Confirm output swing, load capability, stability with capacitive loads, thermal performance, and channel-to-channel behavior under the selected supply voltage and temperature.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2902KDB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2902BDB | LM324BDB | LM324KDB | LM2902KDBG4 | LM2902KDG4 |
|---|---|---|---|---|---|---|
| Package | 14-pin SSOP (DB) | 14-pin SSOP (DB) | 14-pin SSOP (DB) | 14-pin SSOP (DB) | 14-pin SSOP (DB) | 14-pin SSOP (DB) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Special Features | Improved LM2902B generation with 2 kV ESD protection | Improved LM2902B generation | Improved LM324B generation | Legacy LM324 generation | G4 processing designation | G4 processing designation |
Principaux différenciateurs
- Compact four-channel implementation with improved transient robustness (vs LM324KDB)
- Same improved LM2902B electrical family (vs LM324BDB)
- Identical ordering configuration available without electrical changes (vs LM2902KDBG4)
Notes de conception
Place the supply-bypass capacitor as close as possible to the positive supply and ground pins, with a short ground return to the device. Do not split the ground return between distant analog and power sections. Because the four amplifiers share package supply pins, estimate the total supply demand as four channel loads plus the typical 0.8 mA device drain, then verify the regulator's transient response and the package's allowable dissipation under worst-case conditions.
Route each noninverting and inverting input directly to its feedback and source components, avoiding parallel paths beneath or beside the amplifier. High-impedance inputs should be short and guarded against switching-node coupling. The internal compensation makes ordinary closed-loop layouts straightforward, but incorrect feedback connections can create oscillation or saturation. Verify every one of the 14 DB-package pins against the Texas Instruments pin table before releasing the PCB artwork.
Do not infer that the 36 V supply capability stated for other B or BA family versions applies to LM2902KDB; its device listing specifies a 26 V maximum supply rating. Also confirm the input common-mode range and output swing at the chosen supply voltage. The common-mode range includes ground, but that does not mean every output can swing rail-to-rail or that inputs can safely reach the positive rail.
Evaluate the package temperature rise using the worst-case ambient temperature, supply voltage, output voltage, load current, and quiescent dissipation across all four channels. Estimated: power dissipation equals total output current multiplied by the output-to-ground voltage difference plus supply-voltage times total quiescent current. Use the manufacturer thermal parameters for the final junction-temperature calculation and provide copper area or thermal relief appropriate to the PCB and enclosure.
Informations de conformité
The LM2902KDB is associated with industrial, consumer, and automotive applications, but the target's specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer information.