Analog Devices

LT1794IFE - Dual 500mA, 200MHz xDSL Driver | Analog Devices

Référence : LT1794IFE ✓ Actif
±12 V Vdss 500 mA source and sink per channel Id 20-pin TSSOP with exposed pad Package
MOQ : 1 |

LT1794IFE Présentation

The Analog Devices LT1794IFE is a dual 500mA, 200MHz xDSL line-driver amplifier packaged in a 20-pin TSSOP with exposed pad. Each channel can source or sink 500mA, providing the high output-current capability needed to drive xDSL line networks. The amplifier is gain-of-ten stable, has high-impedance balanced inputs, and can be compensated for operation at lower gains.

A line-driver amplifier is a high-speed amplifier optimized for driving transmission lines, isolated telephone pairs, and other loads requiring low distortion and substantial source or sink current. It belongs to the operational-amplifier hierarchy and, more specifically, the interface-driver and xDSL line-driver category. Unlike a general-purpose precision amplifier, the LT1794 prioritizes high bandwidth, extended output swing, and robust drive capability.

The LT1794IFE delivers a 200MHz gain-bandwidth product and supports output swings optimized for operation from ±12V supplies. Its 500mA source-and-sink output current is suited to full-rate xDSL applications. Supply current is set with an external resistor, allowing the system designer to optimize power dissipation according to operating conditions.

The dual configuration provides two independent high-speed channels in one package, reducing board area where two driver circuits are required. Gain-of-ten stability supports direct implementation in conventional line-driver signal paths, while the balanced high-impedance input structure helps preserve source impedance and signal integrity. Lower-gain operation requires appropriate compensation rather than assuming unity-gain stability.

Typical uses include xDSL access equipment, central-office line interfaces, signal-conditioning boards, and high-speed industrial or communications systems that require high current drive into resistive or cable loads. Its 200MHz bandwidth and 500mA output capability are particularly useful when the load must be driven without severe output-current limiting.

When laying out a design, use the exposed pad as a thermal and electrical connection, place input, compensation, and output-signal paths with short return paths, and account for resistor-selected supply current. Verify output swing and thermal dissipation at the lowest expected supply voltage, the highest load current, and the maximum channel activity.

This product overview combines the manufacturer's xDSL line-driver specifications with practical guidance on current drive, gain stability, layout, thermal management, sourcing, and drop-in replacement constraints. It is intended to help engineers evaluate the LT1794IFE against alternatives without overlooking pin compatibility or package-level implementation differences.

Alternatives de remplacement direct pour LT1794IFE — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

LT1794IFE#TR

✅ Remplacement direct
📦 20-TSSOP with exposed pad
Same dual 500mA, 200MHz LT1794 electrical configuration; ordering and tape-and-reel suffix differs by 0% in the stated key ratings

📋 Alternative de référence (hors catalogue)

LT1794IFE#PBF

✅ Remplacement direct
📦 20-TSSOP with exposed pad
Same dual 500mA, 200MHz LT1794 electrical configuration; lead-free ordering suffix differs by 0% in the stated key ratings

📋 Alternative de référence (hors catalogue)

LT1794IFE Valeurs maximales et caractéristiques électriques

Product Type Dual xDSL line-driver amplifier (2 channels)
Minimum Output Current 500 mA source and sink per channel
Gain-Bandwidth Product 200 MHz
Gain Stability 10 (unity-gain stable)
Reference Supply Condition ±12 V
Input Impedance High impedance
Supply Current Configuration Externally resistor-programmed
Configuration de sortie Dual, 2 channels
Output Swing Extended for low-supply-rail operation
Compensation Required for gains below 10
Boîtier 20-pin TSSOP with exposed pad
Package Width 4.40 mm
Type de montage Surface mount

Guide de configuration des broches du LT1794IFE 4.40 mm

Configuration des broches du LT1794IFE (boîtier 4.40 mm). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 4.40 mm pour le LT1794IFE

Aucune donnée de brochage détaillée disponible pour LT1794IFE.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

LT1794IFE convient pour 6 applications: xDSL Access-Line Interface, Central-Office Line Interface, Balanced Differential Driver, High-Speed Instrumentation Output, Communications Test Equipment, High-Speed Audio and Video Interface.

🌐

xDSL Access-Line Interface

The LT1794IFE fits an xDSL access-line interface because each channel combines a 200MHz gain-bandwidth product with 500mA source-and-sink output-current capability. It can drive resistive cable or transformer-coupled line networks while preserving high-speed signal integrity. According to the Analog Devices datasheet, the extended output swing is optimized for operation from ±12V supplies, making the device suitable for full-rate line-driver stages. The circuit designer must select the correct closed-loop gain and compensation, confirm output swing into the actual line impedance, and provide thermal margin for continuous high-current operation.

🏭

Central-Office Line Interface

The LT1794IFE is applicable to central-office equipment requiring two high-speed, high-current drive channels in one package. A 200MHz gain-bandwidth product supports broadband line signals, while the 500mA per-channel output drive provides margin for cable, termination, and isolation-network loads. Gain-of-ten stability permits conventional closed-loop layouts, but compensation must be added when lower gain is required. Layout should preserve short feedback and output paths, connect the exposed pad to the recommended thermal and ground structure, and verify worst-case dissipation with both amplifiers active.

📡

Balanced Differential Driver

The LT1794IFE's balanced, high-impedance inputs make it suitable for differential line-driving stages where source impedance must remain controlled. Its two channels can be arranged around a driver topology while each amplifier contributes 200MHz bandwidth and up to 500mA source or sink capability. Unlike a low-power precision op amp, the LT1794 is designed specifically for higher-current line loads. The implementation should maintain symmetric routing and impedance, use the manufacturer's recommended compensation for the selected gain, and validate common-mode headroom and differential output swing against the cable interface.

🖥️

High-Speed Instrumentation Output

The LT1794IFE can serve as a high-current output stage in industrial signal-conditioning equipment where driving test points, long cables, or terminated loads requires more current than a conventional operational amplifier supplies. The 200MHz bandwidth preserves fast transient content, and the 500mA source-and-sink rating provides useful drive margin. This is a specialty application rather than the primary xDSL use, so engineers must review stability, output-swing limits, and channel-to-channel behavior carefully. Start with the gain-of-ten-stable configuration unless the datasheet's compensation guidance is implemented for a lower gain.

📺

Communications Test Equipment

The LT1794IFE is suitable for communications test equipment that generates or conditions broadband signals through relatively low-impedance or cable-connected loads. Each channel's 200MHz gain-bandwidth product supports high-frequency waveforms, while its 500mA output-current capability reduces the risk of severe current limiting. The device should be used within its specified output-swing and thermal limits, with output protection or attenuation added where accidental shorts are possible. A controlled, short feedback path and careful exposed-pad grounding are important for repeatable amplitude and phase performance.

🎧

High-Speed Audio and Video Interface

The LT1794IFE may be evaluated for high-speed audio or video interfaces that require substantially more output drive than a conventional low-noise amplifier. Its 200MHz gain-bandwidth product and 500mA output-current capability are attractive for cable or transformer drive, although bandwidth alone does not guarantee low distortion across the complete audio range. The circuit should include the manufacturer's recommended compensation and output-stability techniques, particularly if operating below gain 10. Confirm slew rate, output impedance, thermal dissipation, and cable loading before treating this as a conventional audio driver.

What are the key specifications of LT1794IFE that engineers should know?
The LT1794IFE is a dual, gain-of-ten-stable xDSL line-driver amplifier with a 200MHz gain-bandwidth product and 500mA source-and-sink output-current capability per channel. According to the Analog Devices LT1794 datasheet, it uses balanced high-impedance inputs, supports externally set supply current, and is offered in a 20-pin TSSOP with exposed pad. These characteristics distinguish it from ordinary low-power operational amplifiers intended only for signal conditioning.
What is the LT1794IFE and what is an xDSL line-driver amplifier?
The LT1794IFE is a dual high-speed line-driver amplifier designed for xDSL data-communication interfaces. Each channel has a 200MHz gain-bandwidth product and can source or sink 500mA. According to the Analog Devices datasheet, it is gain-of-ten stable, uses balanced high-impedance inputs, and provides extended output swing for low-supply-rail designs. It is therefore more suitable for cable and line driving than a general-purpose precision amplifier.
How much output current can LT1794IFE source and sink?
The LT1794IFE can source or sink 500mA per amplifier channel. According to the Analog Devices LT1794 datasheet, this high-current capability supports full-rate xDSL line-driving applications where the output must drive resistive, cable, or isolated-pair loads. Designers should still check package heat dissipation, output swing, load impedance, and safe operating limits at the maximum expected channel current.
What is the gain-bandwidth product of LT1794IFE?
The LT1794IFE has a 200MHz gain-bandwidth product. According to the Analog Devices datasheet, this bandwidth makes it a high-speed dual voltage-feedback amplifier rather than a conventional audio or instrumentation amplifier. The device is gain-of-ten stable without external compensation, but operation below gain 10 requires the compensation approach described in the datasheet to maintain stable closed-loop behavior.
Is LT1794IFE suitable for xDSL line-driver applications?
The LT1794IFE is specifically suitable for xDSL line-driver applications because it combines a 200MHz gain-bandwidth product with 500mA source-and-sink current per channel. According to the Analog Devices datasheet, its output swing is optimized for full-rate operation from ±12V supplies, while balanced high-impedance inputs support line-interface signal paths. The exact gain, termination, supply, and thermal conditions must still be validated in the target circuit.
Can LT1794IFE operate at gain lower than 10?
The LT1794IFE can be compensated for lower gains, but it is not specified as unity-gain stable in the manufacturer datasheet. According to the Analog Devices documentation, the amplifiers are gain-of-ten stable and should be compensated appropriately when used below gain 10. This distinction is important when comparing the device with amplifiers that offer unconditional unity-gain stability.
Where can I download the LT1794IFE datasheet PDF?
The official LT1794IFE datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/1794fs.pdf. The document contains the electrical characteristics, pin descriptions, application information, compensation guidance, and typical xDSL interface circuits. Use the manufacturer's PDF when assigning PCB pins, selecting external resistors, or checking absolute maximum ratings.
Where can I find the LT1794IFE pinout and package details?
The LT1794IFE pin assignments are shown in the Analog Devices LT1794 datasheet, while the distributor listing identifies the package as a 20-pin TSSOP with exposed pad. Because the exposed pad and compensation pins are electrically important, use the datasheet pin-description table and package drawing during schematic capture and PCB layout rather than relying on a generic connector-style pin diagram.
What is the best drop-in replacement for LT1794IFE?
The best drop-in replacement must use the same 20-pin TSSOP exposed-pad footprint, preserve pin-to-pin assignments, and maintain at least 70% parametric proximity. The available substitution results identify related LT1794 ordering codes and comparison pages but do not establish five distinct, drop-in devices with verified electrical equivalence. Submit the target requirements through the Request a Quote form for package and sourcing review.
What can replace LT1794IFE on an existing PCB?
A PCB-compatible replacement must preserve the LT1794IFE's 20-pin TSSOP exposed-pad footprint, pin functions, supply limits, compensation behavior, and required output-current capability. Related LT1794 ordering codes may represent the same electrical device in different order formats, but they do not create distinct drop-in options. Request a formal compatibility review through the Request a Quote form before changing the approved component.
When should I choose LT1794IFE over another xDSL line driver?
Choose the LT1794IFE when the design needs two independent channels, a 200MHz gain-bandwidth product, 500mA source-and-sink drive per channel, and a 20-pin TSSOP exposed-pad implementation. Compared with a lower-current line driver, it offers more drive margin but also requires careful thermal and output-swing review. Compared with a unity-gain-stable amplifier, it provides stronger line-drive capability but needs compensation below gain 10.
Is LT1794IFE the same as LT1794CFE?
The LT1794IFE and LT1794CFE are related LT1794-family devices, but the verified package listing identifies LT1794IFE as a 20-pin TSSOP with exposed pad. A replacement cannot be judged by the family name alone; package count, pinout, exposed-pad connections, compensation requirements, and electrical limits must match. Treat LT1794CFE as a comparison candidate until its package and pin compatibility are formally confirmed.
Where can I buy LT1794IFE online?
Use the Request a Quote form on this page to request LT1794IFE pricing, current availability, lot traceability, and order handling through XAIPART. The product is listed in production by the manufacturer and appears in the 20-pin TSSOP exposed-pad package. The quote form is the appropriate route for exact-suffix sourcing and procurement without relying on an assumed stock quantity or unsupported delivery date.
What is the price of LT1794IFE?
Pricing for LT1794IFE depends on quantity, order suffix, delivery date, and channel availability, so use the Request a Quote form on this page for a current quotation. The product-page pricing panel reflects quote-first electronic-component sourcing rather than a guaranteed fixed unit price. No firm price or lead-time commitment should be inferred without a quote tied to the required quantity and package configuration.
What is the lead time and stock status of LT1794IFE?
Current stock, lead time, and minimum order quantity for LT1794IFE should be confirmed through the Request a Quote form on this page by stating the required quantity, target date, and permitted order suffix. The manufacturer identifies the LT1794 family as production, but production status alone does not guarantee immediate local inventory. A written quotation supplies the appropriate allocation and delivery commitment.

Données de référence d'ingénierie pour LT1794IFE — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the LT1794IFE when the design requires a dual xDSL line driver with 200MHz bandwidth, 500mA source-and-sink capability per channel, and a 20-pin TSSOP exposed-pad footprint. It is particularly suitable for full-rate access equipment operating from suitably negative and positive supplies where cable, transformer, or termination loading demands high current. Select a unity-gain-stable dual amplifier instead when the required closed-loop gain is below 10 and adding compensation would be undesirable. Select a lower-current dual amplifier when the load requires only conventional op-amp drive and board area or thermal dissipation dominates. No distinct drop-in alternative is asserted because the identified comparison results do not verify a sufficient number of same-footprint, pin-compatible devices with independently validated electrical characteristics.

Comparaison avec les alternatives

Paramètre Ce produit
Product Type Dual xDSL line-driver amplifier
Brand Analog Devices
Package 20-pin TSSOP with exposed pad
Channel Count 2 channels
Gain-Bandwidth Product 200 MHz
— 500 mA source and sink per channel
— Gain of 10; compensation for lower gains
— ±12 V
— Balanced, high-impedance inputs
— Externally resistor-programmed

Principaux différenciateurs

  • High-current output drive for line loads (vs General-purpose dual operational amplifiers)
  • Wide bandwidth for broadband xDSL signals (vs Audio-frequency dual operational amplifiers)
  • Gain-of-ten operation supports stable high-speed feedback (vs Unity-gain-stable dual operational amplifiers)

Notes de conception

Treat the exposed pad as an essential thermal path. Estimated: output dissipation equals the average voltage across the output stage multiplied by load current; with both channels operating, sum the channel dissipation and compare it with the package and PCB thermal limits. Maintain uninterrupted ground-plane connection under the pad, use adequate top- and bottom-layer copper, and verify junction temperature at the maximum expected load rather than relying on no-load calculations.

Place input, feedback, compensation, and output components close to the associated pins to minimize parasitic inductance and maintain control-loop stability. Keep the sensitive input node away from the 500mA output path and exposed-pad supply structure. Route the two channels symmetrically when differential timing matters, provide a continuous ground reference beneath the package, and follow the exposed-pad footprint shown in the Analog Devices package drawing.

Do not assume unity-gain stability: the LT1794 is gain-of-ten stable and requires appropriate compensation when used below gain 10. Also avoid treating the 500mA rating as a continuous all-channel operating point without checking output swing, load impedance, supply voltage, and thermal rise. Select the external supply-current-setting resistor using the manufacturer guidance, and confirm the actual order suffix and exposed-pad connection before PCB release.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The LT1794 is described as a production xDSL line-driver amplifier, but no specific RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration is present in the available manufacturer and distributor information.

Données vérifiées le : 2026-11-09 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

LT1794IFE datasheet LT1794IFE datasheet pdf LT1794IFE pinout Analog Devices LT1794IFE LT1794IFE 500mA output current LT1794IFE 200MHz bandwidth LT1794IFE TSSOP-EP pinout LT1794IFE xDSL line driver LT1794IFE drop-in replacement LT1794IFE equivalent amplifier LT1794IFE price LT1794IFE stock and lead time

Composants & termes associés

Analog Devices LT1794IFE LT1794 xDSL line-driver amplifier dual operational amplifier high-speed voltage-feedback amplifier interface driver signal-conditioning amplifier semiconductor 200MHz gain-bandwidth product 500mA output drive gain-of-ten stable balanced high-impedance input externally resistor-programmed supply current 20-pin TSSOP TSSOP family surface-mount package exposed pad xDSL data communication line termination output swing temperature compensation analog interface
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ