LT1881IS8 - Dual Precision R-R Op Amp | Analog Devices
Référence : LT1881IS8 ✓ ActifLT1881IS8 Présentation
A precision operational amplifier is a voltage-feedback amplifier that provides high open-loop gain and low output impedance while processing signals referenced to its supply rails. The LT1881 belongs to the amplifier hierarchy that includes instrumentation amplifiers, buffer amplifiers, general-purpose amplifiers, and analog signal-chain ICs. Its rail-to-rail output stage can approach the positive and negative supply limits, while the picoamp input specification makes it suitable for high-impedance sources, photodiode interfaces, sensors, and measurement front ends.
The LT1881 family's defining features are its dual configuration, rail-to-rail output, picoamp input bias current, and trimmed input offset voltage of less than 50 uV. The manufacturer data sheet states that input bias current and capacitive-load drive capability are superior to the related LT1884 and LT1885 amplifiers, although this precision comes at the cost of lower speed. The 1 MHz gain-bandwidth product and 0.4 V/us slew rate are therefore appropriate for precision DC and low-frequency signal paths rather than wideband pulse or video applications.
The LT1881 architecture is optimized for accurate amplification around the output-voltage operating point. Because input offset voltage is trimmed below 50 uV and drift remains low, the amplifier can reduce systematic error in slow precision measurements. Rail-to-rail output operation improves usable signal range in single-supply systems, although output-current capability, load stability, noise, and common-mode performance must still be checked against the intended circuit. The dual package also allows two independent amplifier channels in one 8-lead SOIC.
Typical applications include precision current-to-voltage conversion for photodiodes, low-leakage sensor interfaces, low-current measurement, instrumentation signal conditioning, and low-frequency active filtering. The LT1881IS8 is also appropriate when two precision amplifier channels are needed in a compact surface-mount footprint. For applications dominated by switching speed, higher bandwidth, or high capacitive-load drive, a wider-bandwidth amplifier may be a better functional fit.
When designing around the LT1881IS8, verify the input and output common-mode limits at the intended supply voltage and load current. Place feedback components close to the amplifier pins, maintain short input traces, and provide adequate supply-bypass capacitance to minimize parasitic instability or clocking. Do not assume that rail-to-rail output automatically means the input common-mode range reaches both rails; consult the manufacturer data sheet for the exact electrical limits.
This product page combines manufacturer specifications, package information, pin assignments, application guidance, and same-package replacement options. It is structured to help engineers compare precision amplifiers, identify suitable operating conditions, and plan PCB layouts for low-leakage, low-offset instrumentation circuits.
Alternatives de remplacement direct pour LT1881IS8 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
LT1881IS8#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1881IS8#TR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1881IS8#TRPBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1881AIS8#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1881IS8#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1881IS8 Valeurs maximales et caractéristiques électriques
| Number of Amplifier Channels | 2 channels |
| Amplifier Type | General-purpose precision operational amplifier |
| Output Topology | Rail-to-rail output |
| Input Bias Current Class | Picoamp input |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.4 V/us |
| Input Offset Voltage | Less than 50 uV |
| Boîtier | 8-SOIC, 0.154 in (3.90 mm) body width |
| Type de montage | Surface mount |
| Product Lifecycle | PRODUCTION |
Configuration des broches de LT1881IS8
| Broche 1 | OUTA — Amplifier A output |
| Broche 2 | INTA- — Inverting input for amplifier A |
| Broche 3 | INTA+ — Non-inverting input for amplifier A |
| Broche 4 | V- — Negative supply connection |
| Broche 5 | INTB+ — Non-inverting input for amplifier B |
| Broche 6 | INTB- — Inverting input for amplifier B |
| Broche 7 | OUTB — Amplifier B output |
| Broche 8 | V+ — Positive supply connection |
Applications typiques
LT1881IS8 convient pour 6 applications: Photodiode Current-to-Voltage Conversion, Precision Sensor Signal Conditioning, Low-Current Measurement Amplifier, Precision Instrumentation Filtering, Battery-Powered Analog Front End, Low-Level Voltage Buffering.
Photodiode Current-to-Voltage Conversion
The LT1881IS8 fits low-level photodiode front ends because its picoamp-class input bias current reduces the error introduced when the source impedance is high. According to the Analog Devices data sheet, input offset voltage is trimmed to less than 50 uV, which helps limit systematic error when the amplifier converts photocurrent into a voltage. Place the device in a transimpedance configuration with the feedback resistor and compensation capacitor close to the inverting input. The 1 MHz gain-bandwidth product and 0.4 V/us slew rate are suitable for many monitoring and instrumentation bandwidths, but high-speed optical links may require a wider-bandwidth amplifier.
Recommandé
Precision Sensor Signal Conditioning
The LT1881IS8 is well suited to conditioning high-impedance sensor outputs because its picoamp input behavior limits bias-current-induced errors and its rail-to-rail output improves usable range in compact low-power systems. The manufacturer identifies the LT1881 as a precision amplifier with trimmed offset voltage below 50 uV. In a typical application, one channel amplifies the sensor signal while the other handles buffering, gain, or active filtering. The 1 MHz gain-bandwidth product supports closed-loop gains up to roughly 1 MHz divided by the target noise gain, although exact bandwidth, stability, and common-mode limits should be checked in the data sheet.
Recommandé
Low-Current Measurement Amplifier
The LT1881IS8 can serve as the input amplifier in a low-current measurement system where leakage from the amplifier itself could obscure the measured signal. Picoamp-class input bias current is the key benefit, while trimmed input offset below 50 uV limits the voltage error before gain is applied. Use the non-inverting and inverting inputs according to the 8-SOIC pinout and keep sensitive input routing short and guarded against leakage. Its 0.4 V/us slew rate and 1 MHz gain-bandwidth product are appropriate for slow laboratory, process-control, or electrochemical measurements rather than high-speed pulse capture.
Recommandé
Precision Instrumentation Filtering
The LT1881IS8 is appropriate for active-filter stages that require low input bias current and accurate DC behavior. Its 1 MHz gain-bandwidth product provides usable bandwidth for many low-frequency filters, and the rail-to-rail output stage allows a larger signal range than a conventional output stage. When implementing a Sallen-Key or multiple-feedback filter, use resistor and capacitor values that keep closed-loop gain and phase margin within the manufacturer guidance. The 0.4 V/us slew rate can become the limiting factor for large, fast filter transitions, so verify full-scale output behavior rather than relying only on the bandwidth rating.
Recommandé
Battery-Powered Analog Front End
The LT1881IS8 can be used in a battery-powered analog front end when the design requires a compact dual amplifier, low input leakage, and rail-to-rail output operation. The dual channel provides two precision functions in one 8-SOIC package, reducing board area. Its 1 MHz bandwidth supports low-frequency sensing and control signals, while the picoamp input characteristic is valuable when the source impedance rises near the input range limits. Supply-bypass capacitors should be placed close to pins 4 and 8, and the selected operating voltage must be checked against all electrical limits, including common-mode range and output swing.
Recommandé
Low-Level Voltage Buffering
The LT1881IS8 is useful for buffering low-level voltages when source impedance is high and conventional input bias current would create unacceptable loading. Its picoamp input behavior reduces that error, and the trimmed offset voltage of less than 50 uV improves DC fidelity in unity-gain buffer arrangements. The amplifier’s 1 MHz gain-bandwidth product and 0.4 V/us slew rate are adequate for sensors, dividers, and low-bandwidth reference circuits. Layout must still account for parasitic capacitance and input-bias-current errors, especially when the source impedance is very large or the source node changes temperature.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LT1881IS8 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LT1881IS8#PBF | LT1881IS8#TR | LT1881IS8#TRPBF | LT1881AIS8#PBF |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
Principaux différenciateurs
- Picoamp-class input bias current (vs LT1881AIS8#PBF)
- Lower specified input offset voltage (vs LT1881AIS8#PBF)
- Lower specified input offset current (vs LT1881AIS8#PBF)
- Rail-to-rail output precision (vs LT1881IS8#TRPBF)
Notes de conception
Keep the two input pins and feedback components close together and away from switching nodes, inductors, and high-current return paths. A high-impedance LT1881IS8 application can pick up leakage and coupling even though its input bias current is low. Use a guarded ground or driven shield when a sensitive input trace runs beside noisy circuitry, and keep the surrounding copper and conformal-coating conditions consistent with the required leakage budget.
Place the supply-bypass capacitors directly between pins 4 and 8 and the relevant ground or return plane. Maintain short input and output traces to reduce parasitic capacitance and feedback-loop area. Because the amplifier has a 1 MHz gain-bandwidth product, stability depends on noise gain as well as signal gain; include any compensation capacitor required for transimpedance or capacitive-load operation and verify the complete network in simulation.
Do not interpret the rail-to-rail output description as a guarantee of rail-to-rail input operation. Check the exact input common-mode range, output swing, supply limits, and load-current limits in the manufacturer data sheet for the selected grade. Also distinguish LT1881IS8 from suffix-specific orderable codes such as LT1881IS8#PBF, LT1881IS8#TR, or LT1881AIS8#PBF before releasing a PCB or purchasing for production.
Informations de conformité
Compliance status must be confirmed for the exact orderable suffix. The #PBF designation indicates a lead-free ordering code in Analog Devices nomenclature, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations were not identified for this MPN.