LTC2157CUP-14 - Dual 14-Bit 250Msps ADC | Analog Devices
Référence : LTC2157CUP-14 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $213.81 | $213,81 |
| 10 | $195.5 | $1 955,00 |
| 100 | $168.2 | $16 820,00 |
| 500 | $145.8 | $72 900,00 |
| 1 000 | $132.4 | $132 400,00 |
LTC2157CUP-14 Présentation
An ADC (analog-to-digital converter) is a semiconductor device that converts continuous-time analog signals into discrete digital codes. The LTC2157-14 belongs to the pipelined ADC sub-family, which uses multiple cascaded low-resolution stages to achieve high sample rates while maintaining 14-bit resolution. Within the broader taxonomy, this part is a data converter -> ADC -> high-speed pipelined ADC -> dual-channel simultaneous-sampling ADC. Pipelined ADCs are widely used in communications infrastructure, defense electronics, and test and measurement equipment where both speed and resolution matter.
Key features of the LTC2157CUP-14 include a 1.5 Vp-p easy-to-drive input range, 1.25 GHz full-power sample-and-hold bandwidth, an optional clock duty cycle stabilizer, low-power sleep and nap modes, and a serial SPI port for per-channel configuration. The dual channels support either external or internal voltage reference and offer simultaneous sampling for I/Q or diversity receiver architectures. Pin-compatible 12-bit versions are available (LTC2157-12 family), allowing design scalability across resolution requirements.
The architecture is a 14-stage pipelined ADC with proprietary internal calibration, supporting 250 Msps per channel and offering 1:1 S/H-to-ADC ratio. The LVDS DDR outputs ease FPGA/ASIC capture and reduce pin count on the board. The internal reference simplifies BOM, while the external reference option enables system-wide gain calibration in high-linearity applications.
Typical applications include software-defined radio (SDR) receivers, MIMO LTE/WiMAX transceivers, multi-channel data acquisition systems, medical imaging front-ends, and radar/EW signal processing. The dual simultaneous-sampling channels also suit I/Q demodulation and direct-conversion receiver chains.
When designing with this part, place the analog input traces as a 50 ohm differential pair with controlled 100 ohm differential impedance, and keep LVDS outputs length-matched to within 50 mil to preserve timing margin. A solid ground plane beneath the QFN exposed pad is required for thermal dissipation at full sample rate.
This page synthesizes Analog Devices distributor pricing as of 2026-10-13, drop-in same-family alternatives from the LTC215x-14 series, and practical PCB/layout design notes not duplicated in the manufacturer datasheet.
Alternatives de remplacement direct pour LTC2157CUP-14 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LTC2157CUP-14 (même facteur de forme et même empreinte) — différant par Package, Operating Temperature Range, RoHS Status, SNR, Sampling Rate.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
LTC2157IUP-14#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2157CUP-14#TRPBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2156IUP-14
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$134.1 / unité
Voir la fiche technique →LTC2155IUP-14
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$107.04 / unité
Voir la fiche technique →LTC2157CUP-12
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$71.3 / unité
Voir la fiche technique →LTC2156CUP-14
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LTC2157CUP-14 Valeurs maximales et caractéristiques électriques
| Résolution | 14 bits |
| Number of Channels | 2 (simultaneous sampling) |
| Sample Rate | 250 Msps per channel |
| Architecture | Pipelined |
| Input Type | Differential |
| Input Range | 1.5 Vp-p |
| Tension d'alimentation | 1.8 V (single) |
| Total Power Dissipation | 650 mW |
| SNR | 70 dB |
| SFDR | 90 dB |
| Full-Power Bandwidth (S/H) | 1.25 GHz |
| Digital Output | DDR LVDS |
| Reference | Internal or external |
| Configuration Interface | Serial SPI port |
| Boîtier | 64-QFN (9 mm x 9 mm) with exposed pad |
| Pin/Package Code | UP (QFN-64) |
| Plage de température de fonctionnement | 0C to +70C (commercial, C grade) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (PBF suffix) |
| Clock Duty Cycle Stabilizer | Optional, on-chip |
| Sleep/Nap Modes | Yes (low-power) |
Configuration des broches de LTC2157CUP-14
| Broche 1 | GND — Ground |
| Broche 2 | INA+ — Channel A positive differential analog input |
| Broche 3 | INA- — Channel A negative differential analog input |
| Broche 4 | VCM_A — Channel A common-mode voltage |
| Broche 5 | GND — Ground |
| Broche 6 | VREF — Voltage reference (internal or external) |
| Broche 7 | SENSE — Reference mode select |
| Broche 8 | GND — Ground |
| Broche 9 | INB+ — Channel B positive differential analog input |
| Broche 10 | INB- — Channel B negative differential analog input |
| Broche 11 | VCM_B — Channel B common-mode voltage |
| Broche 12 | GND — Ground |
| Broche 13 | CLK+ — Differential clock input positive |
| Broche 14 | CLK- — Differential clock input negative |
| Broche 15 | GND — Ground |
| Broche 16 | OE — Output enable (active high) |
| Broche 17 | GND — Ground |
| Broche 18 | NC — Not connected |
| Broche 19 | NC — Not connected |
| Broche 20 | GND — Ground |
| Broche 21 | OGND — Output logic ground |
| Broche 22 | OVDD — Output logic supply |
| Broche 23 | GND — Ground |
| Broche 24 | NC — Not connected |
| Broche 25 | NC — Not connected |
| Broche 26 | DA0+/DA0- — Channel A LVDS DDR data pair 0 |
| Broche 27 | DA1+/DA1- — Channel A LVDS DDR data pair 1 |
| Broche 28 | DA2+/DA2- — Channel A LVDS DDR data pair 2 |
| Broche 29 | DA3+/DA3- — Channel A LVDS DDR data pair 3 |
| Broche 30 | DA4+/DA4- — Channel A LVDS DDR data pair 4 |
| Broche 31 | DA5+/DA5- — Channel A LVDS DDR data pair 5 |
| Broche 32 | DA6+/DA6- — Channel A LVDS DDR data pair 6 |
| Broche 33 | GND — Ground |
| Broche 34 | DCO+/DCO- — DDR LVDS data clock output pair |
| Broche 35 | FR+/FR- — Frame clock output pair |
| Broche 36 | GND — Ground |
| Broche 37 | DB0+/DB0- — Channel B LVDS DDR data pair 0 |
| Broche 38 | DB1+/DB1- — Channel B LVDS DDR data pair 1 |
| Broche 39 | DB2+/DB2- — Channel B LVDS DDR data pair 2 |
| Broche 40 | DB3+/DB3- — Channel B LVDS DDR data pair 3 |
| Broche 41 | DB4+/DB4- — Channel B LVDS DDR data pair 4 |
| Broche 42 | DB5+/DB5- — Channel B LVDS DDR data pair 5 |
| Broche 43 | DB6+/DB6- — Channel B LVDS DDR data pair 6 |
| Broche 44 | GND — Ground |
| Broche 45 | SDO — SPI serial data output (open-drain) |
| Broche 46 | SDI — SPI serial data input |
| Broche 47 | SCK — SPI serial clock |
| Broche 48 | CS — SPI chip select (active low) |
| Broche 49 | RESET — Hardware reset (active low) |
| Broche 50 | PD — Power-down mode select |
| Broche 51 | NAP — Nap mode select |
| Broche 52 | GND — Ground |
| Broche 53 | VDD — 1.8 V analog supply |
| Broche 54 | GND — Ground |
| Broche 55 | VDD — 1.8 V analog supply |
| Broche 56 | GND — Ground |
| Broche 57 | VDD — 1.8 V analog supply |
| Broche 58 | GND — Ground |
| Broche 59 | VDD — 1.8 V analog supply |
| Broche 60 | GND — Ground |
| Broche 61 | VDD — 1.8 V analog supply |
| Broche 62 | GND — Ground |
| Broche 63 | VDD — 1.8 V analog supply |
| Broche 64 | EP — Exposed pad - thermal and electrical ground (must be soldered) |
Applications typiques
LTC2157CUP-14 convient pour 6 applications: Software-Defined Radio (SDR) Receiver, MIMO LTE / WiMAX Transceiver Baseband, Multi-Channel Data Acquisition System, Medical Imaging Front-End (Ultrasound), Radar and Electronic Warfare Signal Processing, Test and Measurement Instrumentation.
Software-Defined Radio (SDR) Receiver
The LTC2157CUP-14 is well suited to software-defined radio receivers where dual simultaneous-sampling 14-bit channels digitize I/Q baseband or IF signals directly. The 250 Msps per-channel sample rate supports IF bandwidths up to approximately 100 MHz, while the 70 dB SNR and 90 dB SFDR preserve signal fidelity across the dynamic range required by modern digital demodulation. Differential inputs reject common-mode board noise, and DDR LVDS outputs feed directly into FPGAs such as Kintex or Cyclone families without level shifters. Low-power Sleep and Nap modes enable duty-cycled operation for battery-powered tactical or portable SDR platforms.
Recommandé
MIMO LTE / WiMAX Transceiver Baseband
Multi-antenna MIMO LTE and WiMAX transceivers require multiple synchronized ADC channels per antenna branch. The LTC2157CUP-14 provides two simultaneous-sampling 14-bit channels at 250 Msps, allowing two diversity or polarization branches to be digitized by a single IC. The single 1.8 V supply simplifies baseband card power design, while the 650 mW dissipation keeps thermal rise manageable with a modest copper pour. Pin-compatible 12-bit and lower-speed LTC2156/2155 derivatives let designers scale BOM cost and power across product tiers without PCB rework.
Recommandé
Multi-Channel Data Acquisition System
High-channel-count data acquisition systems benefit from the LTC2157CUP-14 dual-channel density: 32 such ICs deliver 64 simultaneous-sampling 250 Msps channels on a single backplane. The 1.25 GHz full-power sample-and-hold bandwidth preserves step-response fidelity for transient captures, while the 14-bit resolution satisfies 80 dB dynamic range requirements for vibration, acoustic, and ultrasonic test stands. The serial SPI configuration port allows per-channel gain and offset trim via a shared microcontroller, and the internal voltage reference eliminates a noise source in the analog front end.
Recommandé
Medical Imaging Front-End (Ultrasound)
Portable and cart-based ultrasound imaging systems rely on dense ADC front-ends to digitize beamformed or pre-beamformed RF echoes. The LTC2157CUP-14 dual-channel architecture doubles the channel count per board while keeping 70 dB SNR adequate for B-mode and Doppler imaging. The 1.5 Vp-p easy-to-drive input range simplifies the LNA/HV-switch interface, and the 1.8 V single supply integrates with low-voltage FPGA SoCs. Optional duty-cycle stabilizer on the clock input compensates for non-50 percent clocks from FPGA PLLs, eliminating tone images at the carrier.
Recommandé
Radar and Electronic Warfare Signal Processing
Phased-array radar and electronic-warfare receivers demand wide instantaneous bandwidth and high spurious-free dynamic range. The LTC2157CUP-14 captures 100 MHz-class IF signals with 90 dB SFDR, allowing small targets to be resolved in dense emitter environments. The dual channels support sum-and-difference or I/Q digitization in monopulse receivers, while Sleep/Nap modes reduce average dissipation in duty-cycled surveillance scans. The 64-QFN package's exposed pad couples to a copper ground pour for thermal stability under extended transmit/receive cycles.
Recommandé
Test and Measurement Instrumentation
High-end oscilloscopes, spectrum analyzers, and arbitrary waveform digitizers leverage the LTC2157CUP-14's 1.25 GHz analog bandwidth and 250 Msps sample rate to deliver 100 MHz-class real-time capture on two channels per chip. The 14-bit resolution extends the dynamic range beyond traditional 8-bit instrument ADCs, supporting cleaner modulation analysis on RF test gear. The internal or external reference option allows precise gain calibration across the instrument's annual recalibration interval, and the SPI port exposes per-channel offset and gain trim for factory alignment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LTC2157CUP-14 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LTC2157IUP-14#PBF | LTC2157CUP-14#TRPBF | LTC2156IUP-14 | LTC2155IUP-14 | LTC2157CUP-12 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-QFN (UP, 9x9 mm) | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same |
| Resolution | 14 bits | 14 bits | 14 bits | 14 bits | 14 bits | 12 bits |
| Sample Rate | 250 Msps | 250 Msps | 250 Msps | 210 Msps | 170 Msps | 250 Msps |
| Channels | 2 simultaneous sampling | 2 simultaneous sampling | 2 simultaneous sampling | 2 simultaneous sampling | 2 simultaneous sampling | 2 simultaneous sampling |
| Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | 0C to +70C (C grade) | -40C to +85C (I grade) | 0C to +70C (C grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | 0C to +70C (C grade) |
Principaux différenciateurs
- Simultaneous dual-channel sampling at 250 Msps with 14-bit resolution (vs LTC2156IUP-14)
- Highest SNR/SFDR pair in the LTC215x-14 family (vs LTC2155IUP-14)
- Industrial-temperature drop-in upgrade path (vs LTC2157IUP-14#PBF)
Notes de conception
Estimated: drive the LTC2157CUP-14 differential analog inputs as a 100 ohm differential pair with length matching within 10 mil and characteristic impedance verified with a TDR or field-solver. Place the input traces on the top layer over a continuous ground plane and keep them isolated from the LVDS digital outputs by at least 200 mil to prevent digital noise coupling into the analog front end. Use an LTC6406 or similar low-noise differential driver if the source is single-ended.
Estimated: the 64-QFN (UP) package dissipates 650 mW under full dual-channel 250 Msps operation. With an estimated theta_JA of approximately 30 C/W on a 4-layer JEDEC test board, junction temperature rises roughly 20 C above ambient. For elevated ambient operation (>50 C) or full lifetime reliability, add a thermal via array directly under the exposed pad connecting to inner ground planes. Avoid placing the IC near other high-power components to minimize thermal gradient across the board.
Length-match each LVDS DDR output (DA0-DA6, DB0-DB6, DCO, FR) within 50 mil to preserve data-eye timing at the FPGA. Place a 100 ohm differential termination resistor across each LVDS pair at the receiver side. Maintain a continuous reference plane beneath LVDS traces and avoid crossing splits to prevent return-path discontinuities that degrade the data eye. The clock duty-cycle stabilizer should be enabled if the incoming CLK+/CLK- signal has a non-50 percent duty cycle.
Decouple each VDD pin with a 0.1 uF X7R ceramic capacitor placed within 3 mm of the pin and a single 10 uF bulk capacitor near the IC. The OVDD (output logic supply) is typically tied to the FPGA I/O voltage (1.8 V or 2.5 V) and should be filtered separately from the analog VDD to prevent digital switching noise from corrupting the analog supply. Use a ferrite bead between analog and digital 1.8 V rails if noise coupling is observed.
Do not float the SENSE pin - tie it to GND for internal reference mode or to VDD for external reference mode. Leave unused LVDS data pairs (if the application uses fewer bits) terminated with 100 ohm differential resistors rather than left open. The exposed pad must be soldered to the PCB ground plane for thermal dissipation and electrical reference; a non-soldered exposed pad will trigger thermal-shutdown behavior at lower ambient temperatures.
Informations de conformité
PBF suffix confirms lead-free and RoHS-compliant finish. Halogen-free status not stated in the verified web data. AEC-Q100 not applicable (this is a commercial-grade high-speed ADC).
