MAX182BCPI - 12-Bit 4-Ch SAR ADC w/ T/H and Reference | Maxim
Référence : MAX182BCPI ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $18.73 | $18,73 |
| 10 | $17.5 | $175,00 |
| 100 | $15.25 | $1 525,00 |
| 500 | $13.4 | $6 700,00 |
| 1 000 | $12.1 | $12 100,00 |
MAX182BCPI Présentation
An ADC (analog-to-digital converter) is a data-conversion integrated circuit that transforms continuous analog voltage signals at its inputs into discrete digital codes at its output, enabling microcontrollers, DSPs, or FPGAs to process real-world sensor signals. Successive-approximation-register (SAR) ADCs use a binary-search algorithm with an internal DAC and comparator to resolve N bits in N clock cycles, trading conversion speed for excellent DC accuracy, low latency, and very low power consumption - making SAR ADCs the dominant topology for industrial process control, instrumentation, and multichannel data-acquisition systems.
Key features of the MAX182BCPI include an internal 2.5 V bandgap reference (with a REFADJ pin for external trim), a track-and-hold with 1.5 MHz full-power bandwidth, a parallel microprocessor interface, hard-wired channel sequencing or software-programmable channel selection, and single +5 V supply operation. The part draws approximately 4 mA active supply current and powers down to microamp-level standby between conversions, simplifying battery and portable designs. Internal autocalibration of linearity and offset runs at power-up and on demand via the CAL pin, eliminating periodic user adjustment.
Typical applications include multichannel process-control data acquisition boards, portable or rack-mounted industrial instrumentation, sensor-signal conditioning front-ends, and embedded microprocessor analog I/O modules where the integrated reference and track-and-hold reduce external bill-of-materials cost and PCB area compared with discrete ADC + reference designs.
When designing with this device, place 0.1 uF ceramic bypass capacitors close to the supply and reference pins, drive analog inputs through low-impedance buffers, and avoid routing digital lines under the analog input traces to preserve 12-bit noise performance.
Alternatives de remplacement direct pour MAX182BCPI — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MAX182BCPI+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX182ACPI+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX182AEPI+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX174ACPI+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX174BCPI+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX182BCPI Valeurs maximales et caractéristiques électriques
| Résolution | 12 bit |
| Number of Input Channels | 4 single-ended / 2 differential (configurable) |
| Architecture | SAR (Successive Approximation Register) |
| Conversion Rate | 17 ksps |
| Input Type | Single-Ended, Pseudo-Differential |
| Data Interface | Parallel |
| Reference Type | Internal 2.5 V bandgap (REFADJ pin for external trim) |
| Tension d'alimentation | +5 V single supply |
| Track-and-Hold Bandwidth | 1.5 MHz (full-power) |
| Température de fonctionnement | 0C to +70C (C grade) |
| Boîtier | 28-pin PDIP (0.600", 15.24 mm) |
| Type de montage | Through-Hole |
| Channel Sequencing | Hardware sequential or software programmable |
| Calibration | Internal on-power-up + on-demand via CAL pin |
Configuration des broches de MAX182BCPI
| Broche 1 | CH0 — Analog input channel 0 |
| Broche 2 | CH1 — Analog input channel 1 |
| Broche 3 | CH2 — Analog input channel 2 |
| Broche 4 | CH3 — Analog input channel 3 |
| Broche 5 | AGND — Analog ground |
| Broche 6 | REF — Reference voltage output (2.5 V internal) |
| Broche 7 | REFADJ — Reference adjust input (external trim) |
| Broche 8 | VDD — +5 V analog supply |
| Broche 9 | DGND — Digital ground |
| Broche 10 | D0 — Data bit 0 (LSB) |
| Broche 11 | D1 — Data bit 1 |
| Broche 12 | D2 — Data bit 2 |
| Broche 13 | D3 — Data bit 3 |
| Broche 14 | D4 — Data bit 4 |
| Broche 15 | D5 — Data bit 5 |
| Broche 16 | D6 — Data bit 6 |
| Broche 17 | D7 — Data bit 7 |
| Broche 18 | D8 — Data bit 8 |
| Broche 19 | D9 — Data bit 9 |
| Broche 20 | D10 — Data bit 10 |
| Broche 21 | D11 — Data bit 11 (MSB) |
| Broche 22 | CS — Chip select (active low) |
| Broche 23 | RD — Read strobe (active low) |
| Broche 24 | WR — Write / convert start (active low) |
| Broche 25 | INT — Interrupt / end-of-conversion output |
| Broche 26 | CAL — Calibration start (active low) |
| Broche 27 | MODE — Channel sequencing mode select |
| Broche 28 | VLOGIC — Logic supply voltage (+5 V) |
Applications typiques
MAX182BCPI convient pour 6 applications: Multichannel Industrial Process Control DAQ, Portable Battery-Powered Instrumentation, Embedded Microprocessor Analog I/O Modules, Sensor Signal Conditioning Front-End, Automated Test Equipment (ATE) Channels, Legacy System Repair and Obsolete-Part Replacement.
Multichannel Industrial Process Control DAQ
The MAX182BCPI's 4 single-ended / 2 differential input channels and 17 ksps throughput make it a strong fit for multichannel industrial process-control data-acquisition boards where multiple sensor signals (temperature, pressure, flow) must be digitized for a PLC or microcontroller. The integrated 2.5 V reference and on-chip track-and-hold eliminate the need for an external reference IC and reduce BOM cost, while internal autocalibration maintains 12-bit linearity without periodic user adjustment. Placed at the analog front-end between sensor signal conditioners and the MCU's parallel bus, the MAX182BCPI delivers low-latency conversions on each channel, making it suitable for closed-loop control loops where conversion delay affects response time. Designers should still add anti-alias filtering on each analog input to preserve 12-bit SNR.
Recommandé
Portable Battery-Powered Instrumentation
The MAX182BCPI's single +5 V supply operation and low active supply current (approximately 4 mA typical) make it suitable for portable or handheld instrumentation such as field meters, data loggers, and battery-powered test equipment. The integrated track-and-hold allows the analog input to settle during acquisition without external buffer amplifiers, simplifying the analog front-end and reducing PCB area. Power-down mode between conversions drops consumption to microamp levels, extending battery life in duty-cycled measurement scenarios. Place 0.1 uF ceramic bypass close to VDD and reference pins, and route analog input traces away from digital lines to preserve noise performance on the 12-bit output.
Recommandé
Embedded Microprocessor Analog I/O Modules
The MAX182BCPI's parallel microprocessor interface (D0-D11 plus CS, RD, WR, INT) makes it a natural fit for embedded analog I/O modules built around 8-bit and 16-bit microprocessors or low-end DSPs. With its hardware-sequential or software-programmable channel selection, a single MAX182BCPI can digitize up to 4 sensor inputs and present them on a single bus to the host processor, eliminating an external analog multiplexer. Internal autocalibration on power-up and on demand via the CAL pin removes the need for software trim loops, simplifying host firmware. Designers should confirm bus-timing compatibility with the host microprocessor and add a latch if required for demultiplexed lower-byte / upper-byte read cycles.
Recommandé
Sensor Signal Conditioning Front-End
The MAX182BCPI's on-chip 2.5 V reference and 1.5 MHz full-power-bandwidth track-and-hold make it suitable as the analog-to-digital front-end for sensor signal-conditioning boards digitizing strain-gauge bridges, thermocouple amplifiers, or transducer outputs. The internal reference provides the low-noise excitation reference for ratiometric measurements, while the track-and-hold allows a wide range of source impedances to settle within the acquisition window. Use it in 4-wire ratiometric measurements where ADC reference and bridge excitation share the same 2.5 V to cancel drift. Consider adding an input buffer amplifier (e.g., MAX4250) if source impedance exceeds the MAX182's recommended maximum.
Recommandé
Automated Test Equipment (ATE) Channels
The MAX182BCPI's 17 ksps sample rate and integrated calibration make it well-suited for low-channel-count automated test equipment, where multiple DUT (device-under-test) analog signals must be digitized for pass/fail comparison. The hardware-sequential channel mode simplifies scanning through multiple test points, while software-programmable mode allows non-sequential measurements on demand. Place the MAX182BCPI on a separate analog ground island connected to the digital ground at a single point near the ADC, and use guard traces around analog inputs to reject digital switching noise from the parallel bus.
Recommandé
Legacy System Repair and Obsolete-Part Replacement
The MAX182BCPI is the designated ADC for many legacy industrial control boards, medical instruments, and laboratory equipment manufactured between the early 1990s and mid-2000s. For service and repair of these systems, the MAX182BCPI+ lead-free variant is the direct replacement with identical pinout and electrical behavior. The same-brand MAX182AEPI+ (extended temperature) or MAX182ACPI+ (commercial + lead-free) variants can also substitute directly when the original part is out of stock. Because all variants share the same 28-pin PDIP footprint, board-level replacement requires no PCB modification - simply desolder the original part and solder in the replacement.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX182BCPI — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX182BCPI+ | MAX182ACPI+ | MAX182AEPI+ | MAX174ACPI+ | MAX174BCPI+ |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 28-PDIP | 28-PDIP - same | 28-PDIP - same | 28-PDIP - same | 28-PDIP - same | 28-PDIP - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Input Channels | 4 SE / 2 DIFF | 4 SE / 2 DIFF | 4 SE / 2 DIFF | 4 SE / 2 DIFF | 8 SE / 4 DIFF | 8 SE / 4 DIFF |
| Operating Temperature | 0C to +70C (C grade) | 0C to +70C | 0C to +70C | -40C to +85C (extended) | 0C to +70C | 0C to +70C |
| Internal Reference | Yes (2.5 V bandgap) | Yes (2.5 V) | Yes (2.5 V) | Yes (2.5 V) | Yes | Yes |
| Lead-Free / RoHS | No (original C grade) | Yes (lead-free) | Yes (lead-free) | Yes (lead-free) | Yes (lead-free) | Yes (lead-free) |
Principaux différenciateurs
- Same-brand direct drop-in upgrade with extended temperature range (vs MAX182AEPI+)
- Higher channel count in same 28-PDIP package (vs MAX174ACPI+)
- Lead-free RoHS compliance variant available with identical die (vs MAX182BCPI+)
Notes de conception
The MAX182BCPI operates from a single +5 V analog supply on VDD plus a +5 V logic supply on VLOGIC. Place a 0.1 uF ceramic bypass capacitor as close as possible to the VDD pin and a 10 uF bulk tantalum or ceramic capacitor at the supply entry point. Add a ferrite bead or 10 ohm resistor in series with VDD to isolate the ADC's analog supply from digital switching noise on the +5 V rail. A separate VLOGIC pin allows the parallel interface to run at a different logic level if needed, but for typical 5 V microprocessors it is tied directly to VDD.
Use a partitioned ground plane with separate analog and digital ground islands joined at a single point near the MAX182BCPI's AGND/DGND pins. Route analog input traces (CH0-CH3) directly to the ADC input pins without crossing digital traces; use guard traces tied to analog ground around sensitive analog input lines. Place the reference bypass capacitor (typically 10 uF) directly between REF and AGND to filter reference noise. Estimated: with the recommended layout, the ADC typically achieves the datasheet 12-bit SNR; poor layout can degrade SNR by 3-6 dB.
Do not exceed the absolute maximum analog input voltage of VDD + 0.3 V on any CH0-CH3 input - the MAX182BCPI inputs are not overvoltage protected and can be damaged by signals beyond the supply rail. Do not omit the 0.1 uF VDD bypass capacitor, or reference noise will couple into the conversions. Avoid driving the parallel data bus with the host microprocessor before the MAX182BCPI has completed its power-up calibration cycle; check the INT pin before reading the first conversion. Do not float the MODE pin - tie it high or low to select the desired channel-sequencing mode.
Informations de conformité
MAX182BCPI (without + suffix) is the original commercial-temperature, lead-bearing variant; RoHS compliance requires the MAX182BCPI+ lead-free version. AEC-Q100 qualification is not applicable for this through-hole PDIP commercial-grade ADC.
