MAX3243ECDB - 3/5 RS-232 Transceiver | Texas Instruments
Référence : MAX3243ECDB ✓ ActifMAX3243ECDB Présentation
An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a cable-based serial port. It belongs to the hierarchy of interface ICs, serial transceivers, and communication-interface semiconductors. The MAX3243ECDB implements the electrical interface required by TIA/EIA-232-F while operating from a single 3-to-5.5-V supply, eliminating the need for a separate bipolar power rail in many applications.
The device combines three RS-232 drivers, five receivers, and automatic direction control through on-chip charge pumps. Its 250-kbps capability supports asynchronous data links while its 3-to-5.5-V supply range accommodates both 3.3-V and 5-V system rails. ESD ratings of ±15 kV on HBM and air-gap discharge, and ±8 kV on contact discharge, improve protection where cables connect to user-accessible equipment.
The MAX3243E device architecture supports the electrical interface between an asynchronous communication controller and a personal computer or terminal. The integrated charge-pump circuitry generates the RS-232 bipolar voltage levels required by the drivers from the low-voltage system supply. This integration reduces board area by removing external charge-pump capacitors while preserving the required interface voltage swing.
Typical uses include industrial serial consoles, data-acquisition equipment, instrumentation, point-of-sale terminals, and embedded systems that need more receivers than drivers. The five receiver channels support monitoring of several status signals, while three driver channels handle transmit, request-to-send, and data-ready control lines. A 28-pin SSOP is useful when the interface density must remain higher than a 16-pin SOIC can accommodate.
When laying out this transceiver, route each connector-side signal away from logic and clock traces, and place the charge-pump capacitor and interface bypass capacitors close to their specified pins. Confirm that the selected cable-side baud rate is supported by the 250-kbps device rating and that firmware honors the receiver and driver channel assignments shown in the manufacturer datasheet.
Alternatives de remplacement direct pour MAX3243ECDB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX3243ECDB (même facteur de forme et même empreinte) — différant par Interface Standard, Maximum Data Rate, Package, Product Type.
SP3243EBCA-L
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TRS3243EIDB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX3243ECDB Spécifications
| Product Type | RS-232 line driver and receiver |
| Number of Drivers | 3 |
| Number of Receivers | 5 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection, HBM | ±15 kV |
| ESD Protection, IEC61000-4-2 Air-Gap Discharge | ±15 kV |
| ESD Protection, IEC61000-4-2 Contact Discharge | ±8 kV |
| Charge-Pump Circuit | Dual |
| Interface Standard | TIA/EIA-232-F |
| Boîtier | 28-pin SSOP, 208 mil |
| Type de montage | Surface Mount |
| Operating Voltage | 3 V to 5.5 V |
| Statut RoHS | Compliant |
Configuration des broches de MAX3243ECDB
| Broche 1 | R1OUT — Receiver 1 output |
| Broche 2 | R1IN — Receiver 1 input |
| Broche 3 | R2OUT — Receiver 2 output |
| Broche 4 | R2IN — Receiver 2 input |
| Broche 5 | R3OUT — Receiver 3 output |
| Broche 6 | R3IN — Receiver 3 input |
| Broche 7 | R4OUT — Receiver 4 output |
| Broche 8 | R4IN — Receiver 4 input |
| Broche 9 | R5OUT — Receiver 5 output |
| Broche 10 | R5IN — Receiver 5 input |
| Broche 11 | T1IN — Driver 1 input |
| Broche 12 | T2IN — Driver 2 input |
| Broche 13 | T3IN — Driver 3 input |
| Broche 14 | GND — Ground |
| Broche 15 | VCC — Positive supply |
| Broche 16 | V+ — Charge-pump capacitor connection |
| Broche 17 | V- — Charge-pump capacitor connection |
| Broche 18 | C1+ — Charge-pump flyback capacitor connection |
| Broche 19 | C1- — Charge-pump flyback capacitor connection |
| Broche 20 | C2+ — Charge-pump flyback capacitor connection |
| Broche 21 | C2- — Charge-pump flyback capacitor connection |
| Broche 22 | T1OUT — Driver 1 output |
| Broche 23 | T2OUT — Driver 2 output |
| Broche 24 | T3OUT — Driver 3 output |
| Broche 25 | NC — Not connected |
| Broche 26 | NC — Not connected |
| Broche 27 | NC — Not connected |
| Broche 28 | NC — Not connected |
Applications typiques
MAX3243ECDB convient pour 6 applications: Industrial Serial Console, Data-Acquisition Equipment, Embedded Controller Debug Port, Point-of-Sale Terminal, Instrumentation and Test Equipment, Network Management and Service Port.
Industrial Serial Console
The MAX3243ECDB fits industrial consoles that require three RS-232 outputs and five monitoring inputs on a single low-voltage supply. Its three drivers can carry transmitted data and modem-control handshakes, while the five receivers can supervise request-to-send, data-ready, and other status signals. Operation from 3 V to 5.5 V simplifies interfacing with 3.3-V or 5-V embedded controllers, and the 250-kbps capability suits asynchronous console links. The connector-side ESD ratings of ±15 kV HBM and air-gap discharge and ±8 kV contact discharge add protection where service personnel connect cables.
Recommandé
Data-Acquisition Equipment
The MAX3243ECDB provides a compact RS-232 interface for laboratory and field data-acquisition equipment. Three driver channels support command transmission and flow-control outputs, while five receiver channels can read remote acknowledgements, triggers, and status flags. The 28-pin SSOP consolidates eight channels of RS-232 connectivity without requiring separate single-channel transceivers. A single 3-to-5.5-V rail supports both 3.3-V control electronics and 5-V legacy subsystems, and the specified 250-kbps rate is suitable for periodic measurement packets and configuration commands.
Recommandé
Embedded Controller Debug Port
The MAX3243ECDB can implement a multi-signal RS-232 debug interface for an embedded control system. A controller at 3.3 V can use one driver for transmit data and additional drivers for handshake signals, while receivers monitor acknowledgement and module-status lines. The 250-kbps operating limit is appropriate for console traffic rather than high-rate file transfer. Its integrated dual charge pump eliminates a separate negative supply, and the 28-pin SSOP keeps the interface compact while providing five inputs for richer handshaking than a two-channel transceiver.
Recommandé
Point-of-Sale Terminal
The MAX3243ECDB suits point-of-sale terminals that need both command output and multiple peripheral-status inputs. Three drivers can operate a transaction port and hardware handshakes, and five receivers can detect printer, scanner, drawer, and system-ready indications. The 3-to-5.5-V supply range allows use with either 3.3-V system logic or a 5-V interface controller. Because retail equipment frequently connects user-accessible RS-232 peripherals, the connector-side ESD ratings provide an important margin, while the 28-pin SSOP keeps routing manageable on a compact terminal board.
Recommandé
Instrumentation and Test Equipment
The MAX3243ECDB is appropriate for programmable instrumentation that exchanges commands and status over RS-232. Three transmitted signals can carry serial data plus hardware flow control, and five received signals support remote triggers, interlock status, or acknowledgements from an external fixture. The 250-kbps rate matches typical instrument-control traffic, while the wide 3-to-5.5-V supply range accommodates mixed legacy and modern logic. The dual charge-pump architecture simplifies the power tree and reduces the number of external components compared with discrete driver-receiver implementations.
Recommandé
Network Management and Service Port
The MAX3243ECDB supports a dedicated RS-232 service connection on routers, switches, and industrial controllers. The transmitter channels can drive console data and flow-control signals, while the receiver channels can monitor remote commands, reset requests, and power status. Its 250-kbps limit is well matched to human-driven terminal sessions and low-rate management commands. Because service ports are often exposed through physical connectors, the ±15-kV HBM and air-gap ESD ratings and ±8-kV contact rating are valuable system-level protections on the connector-side pins.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MAX3243ECDB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SP3243EBCA-L | TRS3243EIDB |
|---|---|---|---|
| Brand | Texas Instruments | SGS-Thomson | Texas Instruments |
| Package | 28-pin SSOP | 28-pin SSOP - same | 28-pin SSOP - same |
| Number of Drivers | 3 | 3 | 3 |
| Number of Receivers | 5 | 5 | 5 |
Principaux différenciateurs
- Five receivers provide more monitoring channels than a standard two-channel RS-232 transceiver (vs MAX3221IPWR)
- Three-driver channel count supports a full multi-signal RS-232 port (vs MAX3221IPWR)
- Higher documented connector-side ESD ratings for exposed serial ports (vs TRS3243EIDB)
- Wide low-voltage supply range supports mixed 3.3-V and 5-V controller systems (vs SP3243EBCA-L)
Notes de conception
Place the charge-pump flyback capacitors and the V+ and V- capacitors directly beside their associated IC pins, with short and symmetric connections to the device. Keep these components away from connector-side driver outputs because switching current in the charge-pump network can couple into adjacent high-impedance receiver traces. Follow the manufacturer datasheet capacitor values and recommended layout because incorrect placement can reduce ESD performance and increase emissions.
Do not treat the MAX3243ECDB logic-side inputs as 5-V-tolerant unless the selected pin meets the datasheet limits. Verify the host controller voltage, receiver thresholds, and maximum input voltage before connecting directly to a 3.3-V or 5-V system. Also avoid driving the three receiver outputs simultaneously with another device, because their outputs are intended to connect to high-impedance controller inputs.
Route connector-side RS-232 nets away from clocks, switching-power nodes, and sensitive analog inputs. Keep the ground reference continuous beneath the device and return connector current through the board ground rather than a narrow signal-ground path. The MAX3243ECDB provides substantial connector-pin ESD ratings, but those ratings do not replace good enclosure grounding, cable design, and external surge protection in severe industrial environments.
Place the supply bypass capacitor at the VCC pin and use a low-inductance connection to the ground plane. The MAX3243ECDB operates from 3 V to 5.5 V, but the correct bypass value and charge-pump capacitor values must follow the manufacturer datasheet. Check that the host controller and transceiver share a compatible ground reference, and avoid long supply traces that allow cable-side transients to disturb the charge-pump supply node.
Informations de conformité
RoHS compliance is indicated for the MAX3243ECDB listing. The RS-232 interface is a commercial interface product, so AEC-Q100 automotive qualification is not applicable. Other environmental declarations require manufacturer confirmation.