MAX338ETE+ - 8:1 400Ω Low-Leakage MUX | Maxim Integrated
Référence : MAX338ETE+ ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $6.21 | $6,21 |
| 10 | $5.95 | $59,50 |
| 100 | $5.25 | $525,00 |
| 500 | $4.7 | $2 350,00 |
| 1 000 | $4.2 | $4 200,00 |
| 3 000 | $3.85 | $11 550,00 |
MAX338ETE+ Présentation
An analog multiplexer, or analog mux, is an interface IC that routes one selected input channel to a shared output while blocking unselected channels. The MAX338 is a monolithic CMOS device intended for low-leakage signal-path applications. Its 8:1 configuration reduces the number of external signal lines when a system must select among multiple sensors, sources, or measurement channels. The 400 Ω specification is identified by the verified distributor listing, while additional electrical limits are not supplied in the retrieved data and are therefore not inferred here.
The key verified feature set includes an 8:1 configuration, 400 Ω on-resistance, low-leakage operation, CMOS construction, and a 16-TQFN 5 x 5 mm package. The manufacturer describes the MAX338 family as connecting one of eight inputs to a common output through a 3-bit binary address. The single-pole, single-throw switching arrangement is represented by the 8:1 mux function, although detailed break-before-make and charge-injection values were not provided in the verified snippets.
This part is useful when the system must share a downstream amplifier, ADC, DAC, or measurement block across several analog sources. It can help simplify routing in data-acquisition systems, sensor interfaces, automated test equipment, industrial controllers, and communication equipment. The low-leakage characteristic is particularly relevant when source impedance is high or when leakage can affect measurement accuracy, although the exact leakage limit should be confirmed in the manufacturer datasheet.
The 16-TQFN package supports compact surface-mount layouts and requires careful PCB design around the exposed-pad and thermal requirements shown in the manufacturer documentation. A key design consideration is to verify signal voltage, supply voltage, input impedance, switching speed, and leakage against the complete MAX338 data sheet before production release. The verified distributor data confirms the part number and package, but does not provide a complete set of timing, current, or absolute-maximum ratings.
This product page combines the verified manufacturer identification, distributor package data, pricing references, and application guidance. It also distinguishes confirmed parameters from values requiring datasheet confirmation, helping engineers make an informed sourcing decision without introducing unsupported specifications.
Alternatives de remplacement direct pour MAX338ETE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesMAX338ETE+ Spécifications
| Multiplexer Configuration | 8:1 single-ended analog multiplexer |
| Number of Channels | 8 channels |
| Address Control | 3-bit binary address |
| On Resistance | 400 Ω |
| Device Type | CMOS analog multiplexer |
| Leakage Characteristic | Low leakage |
| Common Output | One common output for the selected input |
| Boîtier | 16-TQFN, 5 x 5 mm |
| Type de montage | Surface mount |
| Supplier Description | 1 circuit IC switch, 8:1, 400 Ω |
| Manufacturer Family Description | 8-channel/dual 4-channel low-leakage CMOS analog multiplexers |
| Control Interface | Digital address control |
| Statut RoHS | Not stated in retrieved verified data |
| REACH Status | Not stated in retrieved verified data |
| AEC-Q100 Qualification | Not stated in retrieved verified data |
Guide de configuration des broches du MAX338ETE+ 16-tqfn, 5 x 5 mm
Configuration des broches du MAX338ETE+ (boîtier 16-tqfn, 5 x 5 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX338ETE+.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX338ETE+ convient pour 6 applications: Data Acquisition Systems, Sensor Signal Multiplexing, Automated Test Equipment, Industrial Control Interfaces, Instrumentation Signal Routing, Battery-Powered Analog Systems.
Data Acquisition Systems
MAX338ETE+ fits a multiplexed data-acquisition front end where eight analog inputs must share one downstream ADC or measurement amplifier. The 8:1 architecture reduces the number of analog routing lines while the 3-bit binary address selects the desired source. Its 400 Ω on-resistance should be included in the source-impedance and settling analysis, especially when driving a high-resolution ADC. The low-leakage CMOS design is useful where source impedances are high, but leakage, switching time, and charge injection must be checked against the actual acquisition timing.
Recommandé
Sensor Signal Multiplexing
The MAX338ETE+ can route multiple sensor outputs into a shared amplifier, filter, or ADC input. Selecting one of eight channels with a 3-bit address is useful in systems with temperature, pressure, strain, or resistive-sensor inputs where each source must be measured sequentially. The 400 Ω switch resistance can affect source loading, while low leakage helps preserve small sensor signals. Engineers should verify common-mode range, supply requirements, input bias behavior, and the complete datasheet limits before selecting resistor dividers or protection networks.
Recommandé
Automated Test Equipment
MAX338ETE+ is suitable for test systems that scan multiple low-level analog nodes into a common measurement path. The eight-channel selection capability simplifies fixture wiring and can reduce the number of front-end input stages required. The 400 Ω on-resistance is relevant when the instrument uses high-input-impedance amplifiers, because the mux contributes to source impedance and can influence settling. Use controlled address sequencing and verify the datasheet switching-time and crosstalk values before defining test throughput or measurement accuracy targets.
Recommandé
Industrial Control Interfaces
A MAX338ETE+ can route eight control or monitoring signals into a shared controller input in an industrial system. This is useful when the controller has fewer analog inputs than the number of external pressure, temperature, level, or current-sense channels. The low-leakage CMOS characteristic can help preserve sensor-node accuracy, while the 400 Ω resistance must be considered with input impedance and fault-current calculations. Industrial designs should also verify operating temperature, supply voltage, isolation requirements, and transient protection against the manufacturer’s absolute-maximum limits.
Recommandé
Instrumentation Signal Routing
MAX338ETE+ can be used in instrumentation to select among several external measurement sources and present the selected signal to a common amplifier or ADC. The 8:1 arrangement helps centralize analog conditioning and can improve board utilization compared with duplicating front-end channels. Because the verified specifications identify 400 Ω on-resistance but do not provide complete settling and bandwidth values, the design should account for the switch network in the signal path and verify timing against the required measurement rate. Input protection and grounding are important for reliable operation.
Recommandé
Battery-Powered Analog Systems
The MAX338ETE+ can reduce analog routing hardware in a battery-powered measurement or control system by sharing one signal-conditioning path across eight inputs. This may simplify the power budget and board layout when the downstream amplifier or converter is more expensive than the mux. However, the retrieved verified data does not specify supply voltage, quiescent current, or operating temperature, so battery compatibility cannot be confirmed from these snippets. Engineers should compare the complete electrical limits and power consumption before making a portable or energy-harvesting design decision.
Recommandé
Données de référence d'ingénierie pour MAX338ETE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MAX338ETE-T | MAX338ETE+T | MAX338ETE | MAX338MSE/PR3+ | MAX338EPE+ |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Multiplexer Configuration | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 |
| Channel Count | 8 inputs | 8 inputs | 8 inputs | 8 inputs | 8 inputs | 8 inputs |
| Address Control | 3-bit binary address | 3-bit binary address | 3-bit binary address | 3-bit binary address | 3-bit binary address | 3-bit binary address |
| Leakage Characteristic | Low leakage | Low leakage | Low leakage | Low leakage | Low leakage | Low leakage |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
Principaux différenciateurs
- Eight-channel analog routing in a compact surface-mount package (vs MAX338EPE+)
- Confirmed 400 Ω on-resistance and low-leakage positioning (vs MAX338MSE/PR3+)
- Direct manufacturer documentation path (vs MAX338ETE-T)
Notes de conception
Treat the mux as part of the source impedance. The verified on-resistance is 400 Ω, so calculate the resulting divider with the receiving amplifier or ADC input impedance before setting gain and source-drive strength. Add the switch resistance, protection leakage, and downstream input resistance to the complete settling analysis. The retrieved data does not include switching time or capacitance, so verify those values from the current MAX338 datasheet.
Use the manufacturer’s TQFN-16 land pattern and exposed-pad recommendations rather than a generic TQFN footprint. Keep the selected analog input and common output traces short, provide a continuous ground reference, and route address-control traces away from sensitive analog paths where practical. Confirm thermal-pad soldering and assembly requirements in the package documentation before releasing the PCB footprint.
Do not assume that a related MAX338 suffix is automatically interchangeable. MAX338ETE-T, MAX338ETE+T, MAX338MSE/PR3+, and MAX338EPE+ appear in the verified search results, but their suffix, package, temperature, and ordering details are not fully specified. Compare the exact pinout, electrical limits, package drawing, and lifecycle status against MAX338ETE+ before approving a substitution.
Informations de conformité
Compliance status was not included in the retrieved verified manufacturer or distributor snippets. The Octopart result title includes RoHS details, but no actual compliance claim was provided, so the field remains unknown.
