MC3403D - Quad 30 V 1 MHz Op Amp | Texas Instruments
Référence : MC3403D ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1 000 | $0 | $0,00 |
MC3403D Présentation
What is a quad operational amplifier? A quad operational amplifier combines four independent amplifier sections in one IC. These amplifiers serve as the active gain elements in sensors, buffers, analog filters, comparators, and feedback-control circuits. The MC3403 belongs to the operational-amplifier hierarchy, which is part of the broader amplifier-IC and signal-conditioning categories used in industrial control, instrumentation, audio, and communications equipment.
Key verified features include four amplifier circuits, 1 MHz operation, 0.6 V/µs slew rate, a 14-pin SOIC package, and operation from −25 °C to 85 °C. The push-pull output stage supports bidirectional output-current drive in suitable loads, while the quad configuration gives designers four reusable analog channels in one package. These attributes make the MC3403D practical for low-to-moderate-frequency analog signal paths where four similar amplifier functions are required.
The MC3403’s electrical characteristics are described as similar to the popular UA741 family, but its architecture is specifically useful in single-supply applications. Compared with a basic dual-supply-only op amp, the part offers a practical path to operating from a single rail in many circuits. Designers must still check input common-mode limits, output swing, supply current, noise, offset behavior, and stability against the manufacturer datasheet for the exact operating condition.
Typical uses include sensor buffering, low-frequency active filtering, audio preamplification, transducers, analog control loops, and general instrumentation. For a new design, confirm the required input and output voltage ranges, acceptable slew rate, load impedance, noise performance, and temperature limits. For a replacement, verify the exact pinout, supply range, common-mode range, and output-swing requirements rather than relying only on the amplifier count.
A key practical consideration is decoupling. Place the required supply bypass capacitors close to the power pins and keep sensitive input and feedback traces short. The MC3403D is a general-purpose amplifier, not a precision or high-speed device; use a more specialized amplifier when low offset, low noise, high speed, rail-to-rail operation, or extended temperature performance is mandatory.
This page consolidates verified manufacturer and distributor information, drop-in alternatives, application guidance, package details, and selection considerations for engineers evaluating MC3403D. It is intended to support procurement and design review without substituting unsupported specifications for missing datasheet data.
Alternatives de remplacement direct pour MC3403D — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MC3403D (même facteur de forme et même empreinte) — différant par Operating Temperature Range, Gain-Bandwidth Product, Mounting Type, RoHS Status, Lead-Free Status.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
KA3403D
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MC3403D
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →MC3403
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MC3403N
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →LM324DT
✅ Remplacement direct✓ En stock
$0.0827 / unité
Voir la fiche technique →MC3403D Valeurs maximales et caractéristiques électriques
| Product Type | Quad operational amplifier |
| Number of Amplifier Circuits | 4 circuits |
| Supply Voltage Range | ±2.5 V to ±15 V |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Plage de température de fonctionnement | −25 °C to 85 °C |
| Input Type | True differential inputs |
| Type de sortie | Push-pull |
| Common-Mode Reference | Electrical characteristics similar to UA741 |
| Package Type | 14-SOIC |
| Nombre de broches | 14 pins |
| Type de montage | Surface mount |
| Amplifier Configuration | Quad |
| Statut RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
Guide de configuration des broches du MC3403D 14-soic
Configuration des broches du MC3403D (boîtier 14-soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour MC3403D.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MC3403D convient pour 6 applications: Sensor Signal Conditioning, Audio Preamplification, Active Filtering, Industrial Control Loops, Transducer and Bridge Interfaces, Test and Measurement Front Ends.
Sensor Signal Conditioning
The MC3403D is suitable for buffering and amplifying outputs from sensors such as resistive bridges, temperature elements, and low-level analog transducers. Its four-amplifier arrangement allows several conditioning channels to share one 14-SOIC package, while the verified 1 MHz gain-bandwidth product supports signal paths below the amplifier’s higher-frequency limits. True differential inputs are useful when the source has a differential signal. The design must verify input common-mode range, input bias current, output swing, and noise from the manufacturer datasheet before selecting resistor values or fault thresholds.
Recommandé
Audio Preamplification
MC3403D can provide modest-bandwidth audio preamplification for line-level or instrument signals when its verified 1 MHz bandwidth and 0.6 V/µs slew rate are adequate. Four channels allow stereo or multi-channel preamplification to be consolidated in one 14-SOIC package. The device is not presented in the supplied data as a low-noise audio amplifier, so input-referred noise and offset must be checked before using it in a high-fidelity signal chain. Keep the output within the specified swing and provide stable feedback compensation for the selected gain.
Recommandé
Active Filtering
The MC3403D is applicable to first- and second-order active-filter stages operating at low or moderate frequencies. The verified 1 MHz gain-bandwidth figure and 0.6 V/µs slew rate provide useful design context for determining whether the amplifier can support the intended closed-loop gain and transient response. Four amplifiers can implement multiple filter sections without using four separate packages. Verify open-loop gain, noise gain, stability, and output-current limits in the datasheet because those values were not supplied in the verified source snippets.
Recommandé
Industrial Control Loops
The four amplifier channels can be used in industrial control and instrumentation circuits for error amplification, actuator-driver interfaces, and feedback summing. The MC3403D’s general-purpose bipolar architecture, true differential inputs, and single-supply usability make it a practical fit for nonprecision analog control blocks. The verified operating temperature range is −25 °C to 85 °C, which is narrower than many industrial requirements. Confirm environmental limits, supply tolerances, noise, and output-drive requirements before deploying it in a factory or process-control system.
Recommandé
Transducer and Bridge Interfaces
MC3403D is suitable for analog interfaces that need differential excitation, amplification, and buffering around resistive sensors. The true differential input architecture can simplify conditioning of bridge-like or balanced sensor outputs, while four channels allow instrumentation, gain, filtering, and output stages to be grouped. The verified data does not provide input offset, bias current, noise, or common-mode values, so those parameters must be checked from the manufacturer datasheet. Keep sensor excitation and signal-ground paths separated appropriately to avoid corrupting small differential signals.
Recommandé
Test and Measurement Front Ends
The MC3403D can serve as a general-purpose front-end amplifier in test and measurement equipment when low frequency, moderate bandwidth, and multi-channel analog conditioning are sufficient. Its quad architecture helps reduce the number of amplifier packages in a multi-range instrument. The verified 1 MHz gain-bandwidth product and 0.6 V/µs slew rate are the principal timing references, but the supplied data does not establish precision offset, low-noise performance, or calibration stability. Validate those specifications against the measurement accuracy and source impedance requirements before selecting it.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MC3403D — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | KA3403D | MC3403D | MC3403 | MC3403N | LM324D |
|---|---|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | onsemi | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 4 | 4 | 4 | 4 | 4 | 4 |
Principaux différenciateurs
- Four integrated amplifiers in a 14-SOIC package (vs LM324D)
- Verified 1 MHz operation (vs KA3403D)
- True differential-input architecture (vs MC3403)
Notes de conception
The verified MC3403D supply range is ±2.5 V to ±15 V, with a stated maximum supply voltage of 30 V. Design the regulator and decoupling network so normal supply tolerance, startup, and transients do not exceed the manufacturer’s absolute maximum. Place the required bypass capacitors close to the supply pins and use a low-impedance ground return; an amplifier that works on the bench can fail in production if supply noise or layout inductance is uncontrolled.
Use short, direct traces for non-inverting and inverting inputs, especially when the source impedance is high. Keep feedback components close to the relevant amplifier pins and route the output away from sensitive input nodes. The verified 1 MHz gain-bandwidth product and 0.6 V/µs slew rate do not guarantee stable operation at every gain, load, or supply condition; verify the intended noise gain and output load in the manufacturer datasheet before finalizing the feedback network.
Do not assume that a quad amplifier is a precision, rail-to-rail, or unity-gain-stable device without checking the specific datasheet. Verify input common-mode range, output swing, offset, bias current, noise, stability, and temperature limits for every amplifier channel. For replacements, confirm that the package pinout matches rather than relying on the device name, because the supplied results identify MC3403D listings from multiple manufacturers.
Informations de conformité
The supplied verified data does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for MC3403D.
