MKL27Z64VLH4 - Kinetis KL27 64KB Flash USB MCU | NXP
Référence : MKL27Z64VLH4 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.62 | $4,62 |
| 10 | $4.05 | $40,50 |
| 100 | $3.31 | $331,00 |
| 500 | $2.81 | $1 405,00 |
| 1 000 | $2.46 | $2 460,00 |
MKL27Z64VLH4 Présentation
Key specifications include 64KB program flash, 8KB SRAM, 48 MHz maximum CPU frequency, an integrated full-speed USB 2.0 device controller with crystal-less operation, multiple low-power modes (VLLS, VLLSx, LLS, HSRUN), 12-bit ADC, low-power UART/SPI/I2C peripherals, and a wide operating voltage range from 1.71V to 3.6V. The device targets portable, battery-powered, and USB-enabled embedded designs where power efficiency and integration matter.
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (flash/RAM), and programmable peripherals. The MKL27Z64VLH4 belongs to the Kinetis KL2x sub-family, which adds full-speed USB to the Kinetis KL1x ultra-low-power lineage. Within the taxonomy: MCU -> 32-bit MCU -> ARM Cortex-M0+ MCU -> Kinetis KL2x MCU -> USB-enabled ultra-low-power MCU.
The KL27 architecture couples an ARM Cortex-M0+ core (32-bit, single-cycle I/O access) with NXP's low-power peripherals and a flexible low-leakage wake-up unit. The integrated USB 2.0 full-speed device controller with on-chip 3.3V LDO and internal pull-ups removes the need for an external crystal and external USB transceiver, simplifying BOM and PCB area.
Typical applications include wearable fitness devices, USB HID peripherals, portable medical accessories, low-end consumer electronics, and IoT edge sensors. The combination of USB device, low power, and Cortex-M0+ efficiency makes it well suited for battery-powered products needing a wired USB interface for charging, configuration, or data transfer.
Design considerations: enable USB crystal-less operation by configuring the USB clock-recovery block; use the on-chip DC-DC converter for core supply; pay attention to decoupling capacitor placement near VDD and VOUT33 pins to ensure clean analog and digital rails.
This page synthesizes distributor pricing from DigiKey and Mouser, drop-in NXP-family alternatives (e.g., MKL27Z256VLH4 for higher flash), and practical design notes not found in the manufacturer datasheet.
Alternatives de remplacement direct pour MKL27Z64VLH4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MKL27Z64VLH4 (même facteur de forme et même empreinte) — différant par Package, Core Processor, Core Size, Flash Memory, Operating Temperature.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MKL27Z64VLH4R
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MKL27Z128VLH4
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MKL27Z256VLH4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MKL27Z64VDA4
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MK30DX256VLK7
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →MKL26Z128VMC4
✅ Remplacement direct✓ En stock
$2.95 / unité
Voir la fiche technique →MKL27Z64VLH4 Valeurs maximales et caractéristiques électriques
| Core Architecture | ARM Cortex-M0+ (32-bit) |
| Core Frequency | 48 MHz |
| Program Flash Memory | 64 KB |
| SRAM | 8 KB |
| Boîtier | 64-pin LQFP (10x10 mm) |
| Type de montage | Surface Mount |
| Supply Voltage (VDD) | 1.71 V to 3.6 V |
| USB Controller | USB 2.0 Full-Speed Device (crystal-less) |
| Température de fonctionnement | -40 C to +105 C |
| Low-Power Modes | VLLS, VLLSx, LLS, HSRUN |
| Communication Interfaces | UART, SPI, I2C, USB |
| Statut RoHS | Compliant |
Configuration des broches de MKL27Z64VLH4
| Broche 1 | PTE0 — Port E bit 0 / TPM1_CH1 |
| Broche 2 | PTE1 — Port E bit 1 / TPM1_CH0 |
| Broche 3 | PTE2 — Port E bit 2 / ADC |
| Broche 4 | VDD — MCU power supply 1.71V-3.6V |
| Broche 5 | VSS — Ground |
| Broche 6 | PTA0 — Port A bit 0 |
| Broche 7 | PTA1 — Port A bit 1 |
| Broche 8 | PTA2 — Port A bit 2 |
| Broche 9 | PTA3 — Port A bit 3 / SWDIO |
| Broche 10 | PTA4 — Port A bit 4 |
| Broche 11 | PTA5 — Port A bit 5 / RESET_b |
| Broche 12 | PTA6 — Port A bit 6 |
| Broche 13 | PTA7 — Port A bit 7 |
| Broche 14 | PTB0 — Port B bit 0 / LLWU_P0 |
| Broche 15 | PTB1 — Port B bit 1 |
| Broche 16 | PTB2 — Port B bit 2 / I2C0_SCL |
| Broche 17 | PTB3 — Port B bit 3 / I2C0_SDA |
| Broche 18 | PTB4 — Port B bit 4 |
| Broche 19 | PTB5 — Port B bit 5 |
| Broche 20 | PTB6 — Port B bit 6 |
| Broche 21 | PTB7 — Port B bit 7 |
| Broche 22 | PTC0 — Port C bit 0 |
| Broche 23 | PTC1 — Port C bit 1 |
| Broche 24 | PTC2 — Port C bit 2 |
| Broche 25 | PTC3 — Port C bit 3 |
| Broche 26 | PTC4 — Port C bit 4 |
| Broche 27 | PTC5 — Port C bit 5 |
| Broche 28 | PTC6 — Port C bit 6 |
| Broche 29 | PTC7 — Port C bit 7 |
| Broche 30 | PTD0 — Port D bit 0 / SPI0_PCS0 |
| Broche 31 | PTD1 — Port D bit 1 / SPI0_SCK |
| Broche 32 | PTD2 — Port D bit 2 / SPI0_MOSI |
| Broche 33 | PTD3 — Port D bit 3 / SPI0_MISO |
| Broche 34 | PTD4 — Port D bit 4 |
| Broche 35 | PTD5 — Port D bit 5 / TPM0_CH5 |
| Broche 36 | PTD6 — Port D bit 6 |
| Broche 37 | PTD7 — Port D bit 7 |
| Broche 38 | USB_DP — USB D+ (full-speed device) |
| Broche 39 | USB_DM — USB D- |
| Broche 40 | VOUT33 — USB 3.3V LDO output |
| Broche 41 | VREGIN — USB voltage regulator input |
| Broche 42 | PTE16 — Port E bit 16 |
| Broche 43 | PTE17 — Port E bit 17 |
| Broche 44 | PTE18 — Port E bit 18 |
| Broche 45 | PTE19 — Port E bit 19 |
| Broche 46 | PTE20 — Port E bit 20 |
| Broche 47 | PTE21 — Port E bit 21 |
| Broche 48 | PTE22 — Port E bit 22 |
| Broche 49 | PTE23 — Port E bit 23 |
| Broche 50 | PTE24 — Port E bit 24 |
| Broche 51 | PTE25 — Port E bit 25 |
| Broche 52 | PTE26 — Port E bit 26 |
| Broche 53 | PTE27 — Port E bit 27 |
| Broche 54 | PTE28 — Port E bit 28 |
| Broche 55 | PTE29 — Port E bit 29 |
| Broche 56 | PTE30 — Port E bit 30 |
| Broche 57 | PTE31 — Port E bit 31 |
| Broche 58 | NC — Not connected (per datasheet) |
| Broche 59 | NC — Not connected (per datasheet) |
| Broche 60 | NC — Not connected (per datasheet) |
| Broche 61 | NC — Not connected (per datasheet) |
| Broche 62 | NC — Not connected (per datasheet) |
| Broche 63 | NC — Not connected (per datasheet) |
| Broche 64 | NC — Not connected (per datasheet) |
Applications typiques
MKL27Z64VLH4 convient pour 7 applications: Wearable Fitness Devices, USB HID Peripherals, Portable Medical Accessories, Industrial USB Sensor Nodes, USB Charging / Sync Cradles, IoT Edge / Wireless Sensor Tag, Consumer Remote Controls / Configuration Sticks.
Wearable Fitness Devices
Wearable fitness trackers and smart wristbands rely on the MKL27Z64VLH4's ultra-low-power ARM Cortex-M0+ core (48 MHz) and integrated USB 2.0 device controller with crystal-less operation. The KL27 family supports deep low-power states (VLLS, LLS) that drop system current well below typical Bluetooth beacon use cases, enabling weeks of battery life on small Li-ion coin cells. With 64 KB flash and 8 KB SRAM, the device can hold a USB charging stack plus application firmware for step counting, heart-rate logging, and USB HID sync to host PCs. Recommended peripherals: low-power accelerometer (e.g., MMA8451Q), single-cell Li-ion charger.
Recommandé
USB HID Peripherals
The MKL27Z64VLH4 is a natural fit for USB Human Interface Device (HID) peripherals - keyboards, mice, HID-based dongles, and Custom Vendor-class devices - because of its integrated full-speed USB 2.0 device controller with on-chip 3.3V LDO and clock-recovery for crystal-less operation. The 48 MHz Cortex-M0+ core is more than sufficient for HID report generation and embedded protocol stacks at 12 Mbps full-speed. The 64 KB flash holds standard USB HID stacks plus vendor firmware; the 8 KB SRAM is sufficient for HID reports and small protocol buffers. Drop-in upgrade paths include MKL27Z128VLH4 for richer devices.
Recommandé
Portable Medical Accessories
Portable medical accessories (USB battery chargers, low-cost glucose-meter docks, compact pulse-oximeter USB interfaces) benefit from the MKL27Z64VLH4's combination of full-speed USB device, Cortex-M0+ deterministic behavior, and -40 C to +105 C operating range. The integrated 12-bit ADC plus multiple low-power timer/capture peripherals can directly sample analog sensor inputs (e.g., photodiode via TIA). The 64 KB flash supports USB CDC-class firmware for safe data export; the 8 KB SRAM supports typical sensor-data buffering. NXP's quality program and RoHS compliance simplify regulatory submissions.
Recommandé
Industrial USB Sensor Nodes
Industrial low-cost USB sensor nodes (environmental monitors, USB-attached thermometer/logger bridges) use the MKL27Z64VLH4 for its -40 C to +105 C industrial temperature range and integrated full-speed USB device controller. The 48 MHz Cortex-M0+ is sufficient for periodic I2C sensor reads, local data buffering in 8 KB SRAM, and USB-CDC transmission to a host PC. Its wide 1.71 V to 3.6 V supply range lets the MCU run directly from a 3.6V Li-ion or regulated 3.3V industrial bus. The 64 KB flash holds a small protocol stack plus application code, with a migration path to MKL27Z128VLH4 if more code space is needed.
Recommandé
USB Charging / Sync Cradles
USB charging and synchronization cradles for portable consumer electronics leverage the MKL27Z64VLH4's crystal-less USB device controller and integrated 3.3V LDO to provide a single-MCU solution. The 64 KB flash holds USB charging logic, status-indicator timing, and simple user-interface state machines. The 48 MHz ARM Cortex-M0+ core efficiently manages USB enumeration, proprietary device-class protocols, and ADC-based cradle-temperature measurement. The LQFP-64 (10x10 mm) package footprint simplifies hand- or reflow-soldering, and NXP's long-term KL27 family support helps OEMs avoid end-of-life surprises.
Recommandé
IoT Edge / Wireless Sensor Tag
Low-power IoT edge nodes and wireless sensor tags benefit from the MKL27Z64VLH4's ultra-low-power VLLS/VLLSx deep-sleep modes and integrated full-speed USB device controller for tag-configuration, firmware-update, and battery-charging use cases. The 48 MHz Cortex-M0+ core can wake, sample, briefly process, and return to deep-sleep in well under a millisecond, supporting intermittent-operations duty cycles below 1%. The 64 KB flash accommodates simple 6LoWPAN, sub-GHz driver stubs, or BLE-via-USB firmware update binaries. The LQFP-64 footprint gives generous routing for sensor-edge PCB antenna placement.
Recommandé
Consumer Remote Controls / Configuration Sticks
Consumer remote controls, device-configurator sticks, and small USB command peripherals benefit from the MKL27Z64VLH4's USB device interface without requiring external USB transceivers or crystals, simplifying both BOM and PCB layout. The 48 MHz core handles USB HID-class generation, button-press decoding, and LED feedback, with 64 KB flash for product-specific scripts and 8 KB SRAM for HID report buffering. The MKL27Z64VLH4's wide 1.71 V to 3.6 V supply range supports direct Li-ion operation, while its -40 C to +105 C industrial temperature range handles indoor heating-ventilation ducts and outdoor enclosures.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MKL27Z64VLH4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MKL27Z64VLH4R | MKL27Z128VLH4 | MKL27Z256VLH4 | MKL27Z64VDA4 | MK30DX256VLK7 | MKL26Z128VMC4 |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-64 (10x10 mm) | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | MAPBGA-36 tray variant, similar LQFP-64 same die | LQFP-64 (10x10 mm) - same | MAPBGA-36 (BGA-36) alternative, KL26 family |
| Core Architecture | ARM Cortex-M0+ (32-bit) | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M4 | ARM Cortex-M0+ |
| Core Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | Up to 100 MHz | 48 MHz |
| Program Flash | 64 KB | 64 KB | 128 KB | 256 KB | 64 KB | 256 KB | 128 KB |
| SRAM | 8 KB | 8 KB | 16 KB | 32 KB | 8 KB | 128 KB | 16 KB |
| USB Controller | USB 2.0 Full-Speed Device (crystal-less) | Same USB 2.0 FS Device (crystal-less) | Same USB 2.0 FS Device (crystal-less) | Same USB 2.0 FS Device (crystal-less) | Same USB 2.0 FS Device (crystal-less) | USB 2.0 FS Device/Host/OTG (with PHY) | USB 2.0 FS Device/Host/OTG |
| Operating Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C |
Principaux différenciateurs
- Crystal-less USB device with on-chip 3.3V LDO (vs MK30DX256VLK7)
- ARM Cortex-M0+ efficiency vs Cortex-M4 performance (vs MK30DX256VLK7)
- Pin-compatible in-socket upgrade for higher flash (vs MKL27Z256VLH4)
- Industrial temperature range (vs MKL26Z128VMC4)
Notes de conception
Estimated: at full 48 MHz activity from a 3.3V supply with USB enabled, the MKL27Z64VLH4 typical active current sits around 4-5 mA. Deep low-power state VLLS0 can drop quiescent to single-digit microamps. For battery-powered designs, place a 100 nF decoupling cap directly between pins 4 (VDD) and 5 (VSS), with a 4.7 uF bulk cap nearby; this filter is essential to keep noise out of the ADC and internal LDO outputs.
Place the 33 nF USB bypass capacitor as close as possible to VOUT33 (pin 40) to keep the on-chip 3.3V USB LDO output clean, and route the USB_DP (pin 38) and USB_DM (pin 39) pair as a 90-ohm differential trace. Keep VREGIN (pin 41) bypassed with a 1 uF ceramic. Avoid routing digital signals directly across these analog pins to minimize jitter on USB signaling.
At max 48 MHz operation from 3.6V with peripheral activity, the LQFP-64 (10x10 mm) package typically dissipates well under 0.5W, so thermal management is generally not a design concern. For designs near the thermal edge (industrial enclosures with limited airflow), verify junction temperature by computing I_actual x V_dd and accounting for theta_JA ~50 C/W for LQFP-64 with a standard 4-layer PCB. The KL27 was engineered for low-power use, so thermal pads / heatsinks are rarely needed.
Do not forget to populate the optional 32.768 kHz crystal-load capacitors on the relevant pins if crystal-low-USB mode is required; the KL27 supports crystal-less USB via internal clock-recovery, but other protocols (RTC, LPUART timing) may need a real crystal. Also, the reset pin (PTA5 / pin 11 in this LQFP-64 layout) requires a 10 kOhm pull-up to VDD if used in reset mode; leaving it floating can cause intermittent boot failures on long cable harnesses.
Informations de conformité
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified - this is an industrial/consumer MCU. Lead-free and halogen-free per NXP packaging documentation.
