PIC16C64A-20/P - 8-Bit 20MHz OTP MCU 3.5KB | Microchip
Référence : PIC16C64A-20/P ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $15.67 | $15,67 |
| 10 | $14.1 | $141,00 |
| 100 | $12.54 | $1 254,00 |
| 500 | $11.28 | $5 640,00 |
| 1 000 | $10.1 | $10 100,00 |
PIC16C64A-20/P Présentation
Background knowledge: A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral set on one die. The PIC16C family belongs to the 8-bit microcontroller product type, which itself sits inside the broader integrated circuit (semiconductor) hierarchy. OTP memory is programmed once with a device programmer and is non-erasable; the C (CMOS/EPROM) suffix here denotes EPROM-based program storage, distinguishing this part from flash-based PIC16F siblings.
Key features include 22 I/O pins, 8-channel 8-bit analog-to-digital conversion on later silicon revisions of the family, USART serial port, capture/compare/PWM module, and parallel slave port. Wide operating voltage range spans 2.5 V to 6.0 V (commercial, industrial, and extended temperature ranges), with low-power consumption: 5 V at 4 MHz draws only 15 uA typical, and 3 V at 32 kHz draws 1 uA typical - ideal for battery-backed and sleep-dominated designs.
Technical depth: the PIC16C64A uses a Harvard architecture with separate program and data buses, allowing instruction fetch and operand read to occur in the same cycle. Its 14-bit instruction word yields richer addressing than 12-bit predecessors while staying code-density competitive. The architecture is fully static, so the clock can be stopped without losing register state, enabling low-power idle behavior under software control.
Typical applications include industrial control panels, appliance motor control, sensor interfacing, and low-speed serial communication hubs. The 40-pin PDIP footprint also makes it convenient for through-hole hobbyist, educational, and legacy replacement designs where hand-soldering or socketed prototyping is desired.
Design consideration: the /P suffix denotes a plastic 40-pin PDIP package rated for industrial temperature (-40C to +85C). Pin-compatible OTP and EPROM windowed variants share the same footprint, but verify ADC, USART, and CCP peripheral counts when migrating firmware across the family.
This page consolidates distributor pricing, drop-in pin-compatible alternatives from the same PIC16C family, and engineering notes compiled from the manufacturer datasheet and reference designs - information not found in a single distributor listing.
Alternatives de remplacement direct pour PIC16C64A-20/P — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16C64A-20/P (même facteur de forme et même empreinte) — différant par Package, Program Memory Type, Timers, Core Architecture, Program Memory Size.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16C65B-20/P
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F74-I/P
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →PIC16C74B-20/P
✅ Remplacement direct✓ En stock
$5.42 / unité
Voir la fiche technique →PIC16C64A-04I/P
✅ Remplacement direct✓ En stock
$6.1 / unité
Voir la fiche technique →PIC16C64A-10/PT
✅ Remplacement direct✓ En stock
$2.97 / unité
Voir la fiche technique →PIC16C64A-20/P Valeurs maximales et caractéristiques électriques
| Core Architecture | PIC16C6X 8-bit RISC (Harvard) |
| Instruction Set | 35 single-word instructions, 14-bit wide |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 3.5 KB (2K x 14) |
| RAM | 128 bytes |
| Fréquence d'horloge maximale | 20 MHz |
| Operating Voltage Range | 2.5 V to 6.0 V |
| Supply Voltage (commercial) | 4.0 V to 5.5 V typical |
| I/O Pins | 22 |
| Timers | 3 (Timer0, Timer1, Timer2) |
| USART | 1 (SCI) |
| CCP Modules | [DATA_NONEEDED: 2 CCP per datasheet, listed as 2 capture/compare/PWM] |
| Watchdog Timer | Yes (WDT with on-chip RC oscillator) |
| Parallel Slave Port | Yes (8-bit PSP) |
| Power-on Reset | Yes |
| Current @ 5V, 4 MHz | 15 uA typical |
| Current @ 3V, 32 kHz | 1 uA typical |
| Plage de température de fonctionnement | -40C to +85C (industrial) |
| Boîtier | 40-pin PDIP (P) |
| Type de montage | Through-Hole |
| Niveau MSL | Not applicable (through-hole) |
Configuration des broches de PIC16C64A-20/P
| Broche 1 | MCLR/VPP — Master Clear (reset) input / programming voltage |
| Broche 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Broche 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Broche 4 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| Broche 5 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / ADC reference |
| Broche 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Broche 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| Broche 8 | OSC1/CLKIN — Oscillator input / external clock |
| Broche 9 | OSC2/CLKOUT — Oscillator output |
| Broche 10 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / clock input |
| Broche 11 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| Broche 12 | RC2/CCP1 — PORTC bit 2 / CCP1 PWM output |
| Broche 13 | RC3/SCK/SCL — PORTC bit 3 / SPI SCK / I2C SCL |
| Broche 14 | RC4/SDI/SDA — PORTC bit 4 / SPI SDI / I2C SDA |
| Broche 15 | RC5/SDO — PORTC bit 5 / SPI SDO |
| Broche 16 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| Broche 17 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| Broche 18 | GND — Ground reference |
| Broche 19 | VDD — Positive supply voltage |
| Broche 20 | RB0/INT — PORTB bit 0 / external interrupt |
| Broche 21 | RB1 — PORTB bit 1 |
| Broche 22 | RB2 — PORTB bit 2 |
| Broche 23 | RB3 — PORTB bit 3 |
| Broche 24 | RB4 — PORTB bit 4 |
| Broche 25 | RB5 — PORTB bit 5 |
| Broche 26 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Broche 27 | RB7/PGD — PORTB bit 7 / ICSP data |
| Broche 28 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| Broche 29 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| Broche 30 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| Broche 31 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| Broche 32 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| Broche 33 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| Broche 34 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| Broche 35 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| Broche 36 | RE0/RD/AN5 — PORTE bit 0 / PSP read strobe / analog input 5 |
| Broche 37 | RE1/WR/AN6 — PORTE bit 1 / PSP write strobe / analog input 6 |
| Broche 38 | RE2/CS/AN7 — PORTE bit 2 / PSP chip select / analog input 7 |
| Broche 39 | VDD — Positive supply voltage (second pin) |
| Broche 40 | GND — Ground reference (second pin) |
Applications typiques
PIC16C64A-20/P convient pour 6 applications: Industrial Control Panels, Appliance Motor Control, Sensor Data Acquisition Hubs, Educational and Hobbyist Platforms, Legacy Embedded System Replacement, Low-Power Battery Devices.
Industrial Control Panels
The PIC16C64A-20/P's 22 digital I/O, 3 timers, USART, and 20 MHz CPU are well matched to industrial control panels driving relays, solenoids, keypads, and seven-segment displays. Its industrial temperature rating (-40C to +85C) and wide 2.5 V to 6.0 V supply tolerance tolerate harsh factory bus environments including 24 V-derived rails and brown-out conditions. The 3.5 KB OTP program memory holds full state-machine ladder logic plus Modbus ASCII or RTU framing over the USART without needing external ROM. Designers typically place the part on a backplane with optoisolated I/O and a watchdog timer reset supervisor for fault recovery.
Recommandé
Appliance Motor Control
The PIC16C64A-20/P drives brushed DC and small universal motors in appliances through its Capture/Compare/PWM (CCP) modules and 22 I/O pins. At 20 MHz the part generates PWM frequencies high enough to drive 1 ms switching intervals while leaving CPU headroom for closed-loop control, sensor sampling, and user-interface scanning. The PIC16C6X datasheet's CCP and Timer2 modules support period-and-duty control with hardware interrupt on cycle end, simplifying firmware state machines. Operating from a rectified 5 V or 12 V bus, the wide voltage range and industrial temperature tolerance suit white-goods deployments such as washing machines, dishwashers, and HVAC actuators.
Recommandé
Sensor Data Acquisition Hubs
The PIC16C64A-20/P acts as a sensor hub reading thermistors, RTDs, and 4-20 mA loops, then streaming processed data over the on-chip USART. Its 8-bit ADC (per datasheet) and 22 I/O allow multiplexed analog front-end sampling at rates that satisfy slow-loop SCADA applications. Low-power modes - 1 uA typical at 3 V/32 kHz and 15 uA typical at 5 V/4 MHz - extend battery life in remote, sleep-dominated telemetry nodes. The Harvard bus and deterministic 200 ns instruction cycle keep ADC-to-output latency predictable, simplifying CE/FCC EMC compliance for industrial sensor networks.
Recommandé
Educational and Hobbyist Platforms
The PIC16C64A-20/P's 40-pin PDIP through-hole package is a textbook teaching vehicle for embedded programming courses - breadboard-friendly, easy to socket, and supported by MPLAB X IDE plus PICkit programmers. Its 35-instruction RISC core lets students learn assembly and C development on a deterministic architecture without the complexity of modern peripherals. With 3.5 KB OTP and 128 bytes RAM, the part fits classic exercises like LED chasers, keypad locks, and UART-based PC interfaces. The Microchip PIC16C6X family datasheet includes example code, instruction timing tables, and reference schematics tailored for first-time microcontroller users.
Recommandé
Legacy Embedded System Replacement
Many 1990s-era products use the PIC16C64A-20/P in legacy controllers that must still be supported for service, regulatory, or warranty reasons. Because the part retains the same 40-pin PDIP footprint and pinout as the PIC16C65B, PIC16C74B, and PIC16F74, repair depots can substitute a more readily available alternative without PCB rework. The PIC16C6X family's documented instruction-set compatibility preserves firmware binaries, and peripheral register layouts are largely conserved across the OTP-to-flash generations. This makes the PIC16C64A-20/P's alternatives ideal as service-stock components for industrial, medical, and aerospace legacy equipment.
Recommandé
Low-Power Battery Devices
Battery-powered remote controls, electronic locks, and wireless sensor end nodes benefit from the PIC16C64A-20/P's 1 uA typical sleep current and 15 uA active current at 5 V/4 MHz. The wide 2.5 V to 6.0 V supply range accepts two AA cells (3 V nominal) up through a 9 V battery with a linear regulator. With the on-chip watchdog timer and brown-out reset (per datasheet), the part safely recovers from battery sag without external supervisor ICs. The Harvard architecture and deterministic instruction timing give firmware full control over wake-up intervals, enabling multi-year coin-cell life in low-duty-cycle applications such as remote keyless entry or industrial metering.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16C64A-20/P — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16C65B-20/P | PIC16F74-I/P | PIC16C74B-20/P |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-pin PDIP (P) | 40-pin PDIP - same | 40-pin PDIP - same | 40-pin PDIP - same |
| Program Memory | 3.5 KB OTP EPROM | 7.2 KB OTP | 7.2 KB Flash | 4 KB OTP |
| Max Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| RAM | 128 bytes | 192 bytes | 192 bytes | 192 bytes |
| ADC Resolution | 8-bit | 10-bit | 10-bit | 10-bit |
| I/O Pins | 22 | 33 | 33 | 22 |
| Lifecycle Status | NRND | Active | Active | NRND |
| Memory Type | OTP EPROM | OTP EPROM | Flash | OTP EPROM |
Principaux différenciateurs
- Higher clock speed than predecessor (vs PIC16C64A-04I/P)
- Active production status with same package (vs PIC16C65B-20/P)
- OTP EPROM for code-modified designs (vs PIC16F74-I/P)
Notes de conception
Estimated: at 5 V supply and 20 MHz oscillator the PIC16C64A-20/P draws 15 mA typical and 35 mA maximum per the PIC16C6X family datasheet; in sleep mode with WDT disabled current drops below 1 uA. Add a 100 nF decoupling capacitor on each VDD pin (pin 20 and pin 39) within 5 mm of the package, plus a 10 uF bulk capacitor on the supply rail. For battery applications select the LP oscillator mode (32 kHz) and disable unused peripherals to achieve 1 uA typical standby current.
Do not leave the MCLR/VPP pin floating; tie it through a 10 kohm pull-up to VDD for normal operation. In-circuit serial programming (ICSP) requires the RB6/PGC and RB7/PGD pins to be free of strong pull-down or large capacitive loads. When migrating from PIC16C64 to PIC16C64A verify ADC configuration bits, interrupt priorities, and peripheral register addresses, which changed in the silicon revision 'A'.
Place the 40-pin PDIP socket centrally on the PCB to keep trace lengths under 50 mm for all I/O lines. Route the crystal/oscillator traces (OSC1, OSC2) symmetrically and within 10 mm of the MCU, with a guard ground plane underneath to reduce EMI. Keep the parallel slave port (PORTD/RE) traces short and matched, or place a 33 ohm series resistor near the MCU to dampen ringing. If the design uses external interrupts on RB0/INT, add a 100 ohm series resistor and a 100 pF capacitor to ground to suppress ESD-induced false triggers.
Estimated: the 40-pin PDIP has pin pitch 2.54 mm and row pitch 15.24 mm. Reserve at least 5 mm of clearance around the socket for IC extraction tools and for through-hole hand-soldering or wave-soldering tooling. Add a clear silkscreen pin-1 marker dot and label VDD/GND on pins 11/31 (or 20/39) for assembly clarity. For EMC-sensitive designs add a ferrite bead on VDD and a small TVS diode on MCLR/VPP to survive 8 kV ESD contact discharge per IEC 61000-4-2.
Informations de conformité
RoHS status depends on specific date code; original production predates RoHS. Contact Microchip for current compliance documentation. AEC-Q100 not applicable for non-automotive MCU line. Conflict minerals compliant per Microchip policy.
