PIC16F877-10E/PQ - 8-bit 10MHz 14KB FLASH MCU 44-MQFP | Microchip
Référence : PIC16F877-10E/PQ ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.5 | $9,50 |
| 10 | $8.55 | $85,50 |
| 100 | $7.6 | $760,00 |
| 500 | $6.85 | $3 425,00 |
| 1 000 | $6.1 | $6 100,00 |
PIC16F877-10E/PQ Présentation
A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, peripherals and I/O. It sits at the bottom of the embedded compute hierarchy: MCU -> embedded processor -> microprocessor -> CPU -> compute platform. The PIC16F877 family is the 8-bit branch of Microchip's PIC architecture, designed for deterministic real-time control where predictable instruction timing, low cost and ease of in-system programming matter more than raw MIPS. The 'F' suffix denotes FLASH program memory, enabling rapid firmware iteration via ICSP.
Key differentiating specifications include 200 ns instruction cycle time, 14 KB self-programmable FLASH, hardware USART plus SPI/I2C, a 10-bit ADC, ICD (In-Circuit Debugger) support, and a wide 2.0 V to 5.5 V operating voltage range that simplifies battery-powered designs. The 44-pin MQFP footprint supports surface-mount assembly on production PCBs while exposing enough I/O and analog channels for complex sensor and actuator interfaces.
The PIC16F877 architecture uses a Harvard RISC core with separate program and data buses, a hardware multiplier-free instruction set, and direct/indirect addressing modes that simplify C and assembly code generation. In-System Programming (ICSP) via two pins allows firmware updates after PCB assembly, and the Brown-Out Reset (BOR) and Power-On Reset (POR) circuitry protect against corrupted startup states - both critical for unattended industrial installations.
Typical applications include industrial automation controllers, sensor data acquisition nodes, motor control (PWM-driven DC and stepper drivers), HVAC thermostat interfaces, instrumentation front-ends, and embedded educational platforms. The wide voltage tolerance and robust peripheral mix also suit automotive body electronics, security panels, and small home appliances.
When designing with this device, plan oscillator margins for the 10 MHz speed grade (use a 4x PLL-friendly crystal if higher throughput is needed). Allocate one port pin to MCLR for proper reset, place decoupling capacitors within 5 mm of each VDD/VSS pair, and ensure ADC reference decoupling to obtain the documented 10-bit linearity.
This page synthesizes verified distributor pricing, parametric alternatives, pinout reference, and practical design notes not consolidated on any single distributor page - giving engineers a faster sourcing decision for both new designs and legacy product maintenance.
Alternatives de remplacement direct pour PIC16F877-10E/PQ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16F877-10E/PQ (même facteur de forme et même empreinte) — différant par Core Architecture, Timers, Package, Operating Temperature, ADC.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16F877-10E/P
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$4.3 / unité
Voir la fiche technique →PIC16F874A-I/PQ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F877A-I/PQ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F887-I/PQ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16F874T-20I/PQ
✅ Remplacement direct✓ En stock
$7.46 / unité
Voir la fiche technique →PIC16F877-04I/P
✅ Remplacement direct✓ En stock
$4.95 / unité
Voir la fiche technique →PIC16F877-10E/PQ Valeurs maximales et caractéristiques électriques
| Core Architecture | PIC16 (8-bit Harvard RISC) |
| Program Memory Type | FLASH (self-programmable) |
| Program Memory Size | 14 KB (8K x 14 words) |
| RAM Size | 368 bytes |
| EEPROM Size | 256 bytes |
| Maximum CPU Frequency | 10 MHz |
| Instruction Cycle Time | 200 ns |
| Operating Voltage Range | 2.0 V to 5.5 V |
| I/O Pins | 33 |
| ADC | 10-bit, up to 8 channels |
| Timers | 3 (Timer0, Timer1, Timer2) |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Serial Interfaces | USART/SCI + MSSP (SPI / I2C) |
| Parallel Slave Port | Yes |
| Boîtier | 44-pin MQFP (10x10 mm) |
| Type de montage | Surface Mount |
| ICSP / ICD | Supported (2-wire) |
| Température de fonctionnement | -40C to +125C (extended, 'E' suffix) |
| Statut RoHS | Compliant |
| Instruction Set | 35 single-word instructions |
Configuration des broches de PIC16F877-10E/PQ
| Broche 1 | MCLR/VPP/THV — Master Clear (reset) input / programming voltage |
| Broche 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Broche 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Broche 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| Broche 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| Broche 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Broche 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| Broche 8 | RE0/RD/AN5 — PORTE bit 0 / parallel slave port read / AN5 |
| Broche 9 | RE1/WR/AN6 — PORTE bit 1 / parallel slave port write / AN6 |
| Broche 10 | RE2/CS/AN7 — PORTE bit 2 / parallel slave port chip select / AN7 |
| Broche 11 | VDD — Positive supply voltage |
| Broche 12 | VSS — Ground reference |
| Broche 13 | OSC1/CLKI — Oscillator crystal input / external clock in |
| Broche 14 | OSC2/CLKO — Oscillator crystal output / clock out |
| Broche 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| Broche 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 I/O |
| Broche 17 | RC2/CCP1 — PORTC bit 2 / CCP1 I/O |
| Broche 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Broche 19 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| Broche 20 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| Broche 21 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| Broche 22 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| Broche 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Broche 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| Broche 25 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| Broche 26 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| Broche 27 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| Broche 28 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| Broche 29 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| Broche 30 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| Broche 31 | VSS — Ground reference |
| Broche 32 | VDD — Positive supply voltage |
| Broche 33 | RB0/INT — PORTB bit 0 / external interrupt |
| Broche 34 | RB1 — PORTB bit 1 |
| Broche 35 | RB2 — PORTB bit 2 |
| Broche 36 | RB3/PGM — PORTB bit 3 / low-voltage ICSP programming |
| Broche 37 | RB4 — PORTB bit 4 |
| Broche 38 | RB5 — PORTB bit 5 |
| Broche 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Broche 40 | RB7/PGD — PORTB bit 7 / ICSP data |
| Broche 41 | NC — Not connected (per datasheet) |
| Broche 42 | NC — Not connected (per datasheet) |
| Broche 43 | NC — Not connected (per datasheet) |
| Broche 44 | NC — Not connected (per datasheet) |
Applications typiques
PIC16F877-10E/PQ convient pour 7 applications: Industrial Automation Controller, Sensor Data Acquisition Node, Motor Control (PWM DC / Stepper Driver), HVAC Thermostat Interface, Instrumentation Front-End, Educational / Development Platform, Security / Access Control Panel.
Industrial Automation Controller
The PIC16F877-10E/PQ's 33 digital I/O, hardware USART, SPI/I2C and 10-bit ADC make it well suited as a low-cost PLC or sensor hub in industrial automation. Its 14 KB FLASH holds ladder-logic style control firmware plus serial protocol stacks, while the 368 byte RAM is sufficient for buffering Modbus RTU frames from a slave device. The extended -40C to +125C temperature range tolerates factory-floor heat, and the 44-pin MQFP supports both hand-soldered prototypes and SMT production. Engineers typically pair it with a 24V-to-5V isolated supply and RS-485 transceiver for Modbus nodes.
Recommandé
Sensor Data Acquisition Node
With its 8-channel 10-bit ADC and 33 I/O, the PIC16F877-10E/PQ functions as a multi-sensor data acquisition front-end in remote telemetry or environmental monitoring. The 14 KB FLASH accommodates averaging/calibration firmware and a lightweight UART stack, while the hardware MSSP supports I2C sensor clusters (temperature, humidity, pressure). Power consumption at 10 MHz from 5V is modest enough for solar-battery installations, and the wide 2.0 V to 5.5 V VDD simplifies battery-direct designs. The MQFP-44 footprint also enables high-density PCB integration.
Recommandé
Motor Control (PWM DC / Stepper Driver)
The PIC16F877-10E/PQ provides two CCP/PWM modules and three timers, enabling direct H-bridge PWM control of small DC motors and unipolar stepper drivers. Its 200 ns instruction cycle supports deterministic commutation loops at modest RPM, and 33 I/O accommodate direction, enable, brake and limit-switch lines without external logic. The 10 MHz clock is adequate for PWM frequencies in the low kHz range needed for hobby robotics and small appliances, while the 44-pin MQFP allows compact SMT assembly. Use the PIC16F877A-I/PQ variant when higher PWM frequency or 20 MHz throughput is required.
Recommandé
HVAC Thermostat Interface
The PIC16F877-10E/PQ's combination of 10-bit ADC, USART, LCD-drive capable I/O and wide temperature range makes it a reliable HVAC thermostat controller. Engineers can read thermistor/resistor-network temperature sensors via ADC, drive a character LCD directly through PORTD, and communicate with a fan-coil unit via USART. The 14 KB FLASH stores scheduling/PI-control firmware, and the 368 byte RAM buffers setpoint changes without flicker. The 44-pin MQFP keeps the design compact and SMT-friendly for wall-mounted enclosures.
Recommandé
Instrumentation Front-End
Laboratory and field instrumentation leverages the PIC16F877-10E/PQ's 10-bit ADC, USART and I2C/SPI to digitize analog signals and stream them to a host PC or display. Its 14 KB FLASH accommodates calibration tables, linearization routines, and a command parser for SCPI-like serial control. The Harvard architecture delivers deterministic ADC-to-output latency, which simplifies time-correlated measurements. The 44-pin MQFP enables compact PCB layouts that fit inside handheld instrument housings.
Recommandé
Educational / Development Platform
The PIC16F877-10E/PQ is widely used in university embedded-systems courses because its 35-instruction RISC core, 14 KB FLASH and rich peripheral set (USART, SPI, I2C, ADC, PWM) let students explore all major MCU concepts in one chip. The MQFP-44 package is breadboard-friendly via carrier boards, ICSP enables in-circuit programming without chip removal, and the PIC16 instruction set is simple enough to teach assembly fundamentals. The extended temperature grade also supports lab use in unheated enclosures during outdoor projects.
Recommandé
Security / Access Control Panel
The PIC16F877-10E/PQ's 33 I/O, USART and EEPROM make it suitable for small security panels handling keypads, magnetic-door sensors, sirens and serial uplinks to a central station. The 256-byte EEPROM stores access codes and event logs non-volatilely, and 14 KB FLASH holds the event scheduler plus alarm-state machine. The extended -40C to +125C range supports outdoor enclosures, and the 44-pin MQFP enables a single-PCB solution. Pair with a PIC16F877A-I/PQ upgrade for sites requiring 20 MHz response.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16F877-10E/PQ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16F877-10E/P | PIC16F874A-I/PQ | PIC16F877A-I/PQ | PIC16F887-I/PQ | PIC16F874T-20I/PQ | PIC16F877-04I/P |
|---|---|---|---|---|---|---|---|
| Package | MQFP-44 (PQ) | PDIP-40 - not pin-compatible (verify footprint) | MQFP-44 (PQ) - same | MQFP-44 (PQ) - same | MQFP-44 (PQ) - same | MQFP-44 (PQ) - same | PDIP-40 - not pin-compatible (verify footprint) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Max Clock Frequency | 10 MHz | 10 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 4 MHz |
| FLASH Program Memory | 14 KB | 14 KB | 7 KB (-50%) | 14 KB | 14 KB | 7 KB (-50%) | 14 KB |
| RAM | 368 bytes | 368 bytes | 192 bytes (-48%) | 368 bytes | 368 bytes | 192 bytes (-48%) | 368 bytes |
| Min Operating Voltage | 4.0 V (typical, datasheet) | 4.0 V | 2.0 V | 2.0 V | 2.0 V | 2.0 V | 4.0 V |
| ADC Resolution | 10-bit | 10-bit | 10-bit | 10-bit (faster conversion) | 10-bit (improved linearity) | 10-bit | 10-bit |
| Temperature Grade | Extended (-40C to +125C) | Extended | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
| Lifecycle / Recommendation | Active, legacy - migrate to PIC16F887 | Active, legacy | Active | Active | Active - recommended for new designs | Active | Active, legacy |
Principaux différenciateurs
- PIC16F877A-I/PQ runs at 20 MHz vs 10 MHz on the original - 100% higher throughput (vs PIC16F877A-I/PQ)
- PIC16F887-I/PQ retains 14 KB FLASH and adds modernized silicon (vs PIC16F887-I/PQ)
- Extended -40C to +125C temperature grade for harsh environments (vs PIC16F877A-I/PQ)
Notes de conception
Place a 100 nF decoupling capacitor within 5 mm of each VDD/VSS pair (pins 11/12 and 31/32 on the MQFP-44 package). Add a bulk 10 uF tantalum or aluminum polymer capacitor at the board power entry. The PIC16F877 has two VDD/VSS pairs that must both be connected - leaving either pair floating causes erratic ADC readings and brown-out resets. For battery applications, leverage the PIC16F877A-I/PQ upgrade which supports 2.0 V min VDD versus the original PIC16F877's 4.0 V minimum.
The MCLR pin (pin 1) must NOT be left floating - either tie it to VDD through a 10 kohm resistor for normal operation or to the ICSP programmer's VPP line. A floating MCLR causes random resets in noisy environments. Configuration bits (_CONFIG) must be programmed correctly: disable the watchdog timer (WDTE) unless firmware uses it, set the oscillator to HS for >4 MHz crystals, and enable Brown-Out Reset (BOREN) for industrial reliability.
Route the 10 MHz crystal traces (OSC1 pin 13, OSC2 pin 14) as short as possible, keep them away from high-current switching traces, and guard them with a ground pour. Place load capacitors (typically 15-33 pF for an HS-mode crystal) directly between OSC1/OSC2 and ground. The 44-pin MQFP thermal pad is not present on this package, but ensure adequate copper around VDD/VSS pins for heat spreading - at 10 MHz and 5 V the part dissipates roughly 50 mW which is well within the package rating.
The 10-bit ADC achieves its specified linearity only with proper analog reference decoupling. Place a 100 nF ceramic + 10 uF tantalum on VREF+/VREF- (pins 5/4) within 10 mm of the pins, and use separate analog and digital ground planes joined at a single point near the MCU. For sensor inputs, add a 100 ohm series resistor + 100 nF cap to ground as an RC anti-aliasing filter at the ADC pin. The ADC acquisition time must be observed in firmware (typically 19.72 us at 10 MHz) before initiating conversion.
Informations de conformité
RoHS compliance per Microchip product page. Microchip holds QS-9000 quality certification for PICmicro 8-bit MCUs per digchip.com datasheet page. Not AEC-Q100 qualified; for automotive applications contact Microchip for PIC16F877A-E/PQ automotive-grade variants.
