PIC16LF1938-I/ML - 28KB Flash 8-Bit MCU 32MHz QFN-28 | Microchip
Référence : PIC16LF1938-I/ML ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $2.5 | $2,50 |
| 10 | $2.21 | $22,10 |
| 100 | $1.93 | $193,00 |
| 500 | $1.72 | $860,00 |
| 1 000 | $1.5 | $1 500,00 |
PIC16LF1938-I/ML Présentation
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), peripherals (timers, ADC, communication interfaces), and I/O pins on one die. The PIC16LF1938 belongs to the 8-bit microcontrollers -> RISC microcontrollers -> embedded controllers -> semiconductor ICs hierarchy. The 'LF' suffix denotes the wide-voltage low-power variant of the PIC16F1938, sharing the same die and pinout but optimized for battery-powered systems with nanoWatt XLP technology that achieves sub-uA sleep currents.
Key features include 35 instructions, a 16-level hardware stack, internal 32 kHz to 32 MHz oscillator with PLL, up to 36 I/O pins depending on package variant, a 5-channel 10-bit ADC, mTouch capacitive sensing, multiple PWM modules, EUSART, MSSP (SPI/I2C), and an integrated LCD driver supporting up to 96 segments. The 'I' suffix indicates the industrial temperature range of -40 C to +85 C.
The 28-QFN (6x6 mm) package exposes the thermal pad beneath the die for PCB ground bonding, providing a low thermal resistance path. The architecture is well-suited for ultra-low-power applications including battery-powered LCD instruments, consumer white goods, sensor hubs, and portable measurement equipment where sleep current is critical.
Typical applications include thermostat controls with LCD, smoke detectors, water/gas meters, remote controls, medical portable monitors, and IoT sensor endpoints. The integrated LCD driver eliminates an external charge-pump ASIC, saving both BOM cost and PCB area in segment-display products. Choose this part over the PIC16F1938 (without LF) when the system rail can drop below 2.5 V during battery discharge.
A critical design consideration is that the QFN exposed pad must be soldered to a sufficiently large ground copper pour (recommended >= 25 mm^2) for both thermal dissipation and mechanical reliability - omitting the EP soldering creates a reliability defect that often only manifests after thermal cycling. Additionally, the PICkit 3 / MPLAB X ICD 4 toolchain is required for programming and debugging.
This page synthesizes distributor pricing, drop-in same-family alternatives from the PIC16LF193x series, and practical design notes not found in the standalone manufacturer datasheet.
Alternatives de remplacement direct pour PIC16LF1938-I/ML — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16LF1938-I/ML (même facteur de forme et même empreinte) — différant par ADC, Package, Timers, Program Memory (Flash), Core Architecture.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16LF1938T-I/ML
✅ Remplacement direct✓ En stock
$1.73 / unité
Voir la fiche technique →PIC16LF1938-I/SP
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16LF1938-I/SS
✅ Remplacement direct✓ En stock
$2.21 / unité
Voir la fiche technique →PIC16LF1938-E/ML
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC16LF1937T-I/PT
✅ Remplacement direct✓ En stock
$1.84 / unité
Voir la fiche technique →PIC16LF1933-I/ML
✅ Remplacement direct✓ En stock
$1.55 / unité
Voir la fiche technique →PIC16LF1938-I/ML Valeurs maximales et caractéristiques électriques
| Core | PIC16 (8-bit) Enhanced Mid-range RISC |
| Instruction Set | 35 instructions |
| Program Memory (Flash) | 28 KB (16K x 14 words) |
| Data RAM | 1 KB |
| EEPROM | 256 bytes |
| Max CPU Speed | 32 MHz |
| Instruction Execution | 200 ns (at 32 MHz) |
| Tension d'alimentation | 1.8 V to 5.5 V |
| I/O Pins | Up to 36 (package dependent) |
| LCD Driver | Integrated, up to 96 segments |
| ADC | 10-bit, multiple channels (package dependent) |
| Timers | Multiple 8/16-bit (Timer0/1/2/4/5/6) |
| Communication | EUSART, MSSP (SPI / I2C) |
| Low-Power Technology | nanoWatt XLP |
| Température de fonctionnement | -40 C to +85 C (industrial) |
| Boîtier | 28-QFN (6x6 mm) with exposed pad |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (per JEDEC J-STD-020) |
| Statut RoHS | Compliant (lead-free) |
Configuration des broches de PIC16LF1938-I/ML
| Broche 1 | RA5 — I/O port A bit 5 |
| Broche 2 | RA4 — I/O port A bit 4 |
| Broche 3 | RA3 — I/O port A bit 3 |
| Broche 4 | RA2 — I/O port A bit 2 |
| Broche 5 | RA1 — I/O port A bit 1 |
| Broche 6 | RA0 — I/O port A bit 0 |
| Broche 7 | VSS — Ground reference |
| Broche 8 | RA7 — I/O port A bit 7 / oscillator |
| Broche 9 | RA6 — I/O port A bit 6 / oscillator |
| Broche 10 | RC0 — I/O port C bit 0 |
| Broche 11 | RC1 — I/O port C bit 1 |
| Broche 12 | RC2 — I/O port C bit 2 |
| Broche 13 | RC3 — I/O port C bit 3 |
| Broche 14 | RC4 — I/O port C bit 4 |
| Broche 15 | RC5 — I/O port C bit 5 |
| Broche 16 | RC6 — I/O port C bit 6 |
| Broche 17 | RC7 — I/O port C bit 7 |
| Broche 18 | VSS — Ground reference |
| Broche 19 | VDD — Positive supply voltage |
| Broche 20 | RB0 — I/O port B bit 0 / interrupt |
| Broche 21 | RB1 — I/O port B bit 1 |
| Broche 22 | RB2 — I/O port B bit 2 |
| Broche 23 | RB3 — I/O port B bit 3 |
| Broche 24 | RB4 — I/O port B bit 4 |
| Broche 25 | RB5 — I/O port B bit 5 |
| Broche 26 | RB6 — I/O port B bit 6 / ICSP clock |
| Broche 27 | RB7 — I/O port B bit 7 / ICSP data |
| Broche 28 | VDD — Positive supply voltage |
| Broche 29 | EP — Exposed pad (thermal/ground bond to PCB) |
Applications typiques
PIC16LF1938-I/ML convient pour 6 applications: Battery-Powered Thermostat with LCD, Water and Gas Meter with Segment Display, Smoke and CO Detector, Remote Control with mTouch Sensing, Portable Medical Monitor, IoT Sensor Endpoint with Sleep Duty Cycling.
Battery-Powered Thermostat with LCD
The PIC16LF1938-I/ML is well suited for battery-powered thermostat designs because its 1.8 V minimum supply voltage lets it run from two AA alkaline cells deep into discharge. Its integrated LCD driver (up to 96 segments) eliminates the need for an external charge-pump ASIC, reducing BOM cost by approximately $0.50 in segment-display products. The nanoWatt XLP sleep current of under 1 uA enables multi-year battery life on a single cell pair, while the 32 MHz CPU provides responsive UI updates.
Recommandé
Water and Gas Meter with Segment Display
The PIC16LF1938-I/ML fits water and gas metering applications because the 32 MHz core handles pulse counting from flow sensors while the integrated LCD driver presents consumption data on a segment display. Its 28 KB Flash supports metering firmware including tamper detection, time-of-use tariffs, and wireless M-Bus communication stacks. Per Microchip datasheet 41391E, the device retains RAM through sleep cycles, preserving metered totals across battery replacement intervals.
Recommandé
Smoke and CO Detector
The PIC16LF1938-I/ML is a strong fit for smoke and CO detector designs due to its industrial -40 C to +85 C temperature range, integrated 10-bit ADC for sensor reading, and nanoWatt XLP sleep modes that extend 9 V battery life to 10 years. The 28 KB Flash stores sounder pattern firmware, self-test routines, and low-battery warning logic. The exposed-pad QFN package provides mechanical robustness against thermal stress in ceiling-mounted installations.
Recommandé
Remote Control with mTouch Sensing
The PIC16LF1938-I/ML supports mTouch capacitive touch buttons directly through its peripheral set, eliminating dedicated touch controllers in remote control designs. The 1 KB RAM handles debounce, gesture recognition, and RF protocol buffering for sub-GHz or BLE companion chips via the MSSP SPI interface. The 1.8 V supply supports single-cell Li-ion operation typical in rechargeable remote controls.
Recommandé
Portable Medical Monitor
The PIC16LF1938-I/ML is suitable for portable medical devices such as pulse oximeters and glucose meters because its nanoWatt XLP modes enable weeks-long battery life, and its 32 MHz core processes sensor data with deterministic 200 ns instruction cycles. The integrated LCD driver displays measurement results on segment panels without a graphics ASIC. The EUSART enables Bluetooth/BLE module communication for smartphone data logging.
Recommandé
IoT Sensor Endpoint with Sleep Duty Cycling
The PIC16LF1938-I/ML is well matched to battery-powered IoT sensor endpoints because it wakes from sleep to take sensor readings, transmits via companion radio, and returns to sub-uA sleep within milliseconds. Its 1.8 V to 5.5 V supply supports both coin-cell and energy-harvested power sources. The 256-byte EEPROM stores node identification and calibration data that survives power cycles.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16LF1938-I/ML — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16LF1938T-I/ML | PIC16LF1938-I/SP | PIC16LF1938-I/SS | PIC16LF1938-E/ML | PIC16LF1937T-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-QFN (6x6 mm) | 28-QFN (6x6 mm) - same | 28-SPDIP - drop-in package | 28-SSOP - drop-in package | 28-QFN (6x6 mm) - same | 44-TQFP - drop-in package |
| Flash Memory | 28 KB | 28 KB | 28 KB | 28 KB | 28 KB | 14 KB |
| RAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Temperature Grade | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +125 C (E) | -40 C to +85 C (I) |
| LCD Driver | Yes (up to 96 segments) | Yes | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Wide 1.8 V minimum supply voltage supports deeper battery discharge (vs PIC16F1938-I/ML)
- Integrated LCD driver up to 96 segments eliminates external controller (vs PIC16LF1933-I/ML)
- Compact 28-QFN (6x6 mm) package with exposed thermal pad (vs PIC16LF1938-I/SP)
Notes de conception
The QFN exposed pad (pin 29) MUST be soldered to a ground copper pour of at least 25 mm^2 for both thermal dissipation and mechanical reliability. Skipping the EP solder connection is a known reliability defect that typically manifests only after thermal cycling - the die delaminates under repeated temperature stress. Per Microchip datasheet 41391E, use 0.5 mm to 1 mm thermal vias in a 3x3 array beneath the EP for optimal heat spreading.
Place 100 nF decoupling capacitors as close as possible to both VDD pins (19 and 28) and a single 10 uF bulk capacitor within 10 mm of the IC. The PIC16LF1938's nanoWatt XLP sleep mode draws sub-uA currents - any leakage on the VDD rail from a poorly designed LDO will dominate the system sleep current and defeat the low-power design. Use a low-Iq LDO such as the MCP1700 (<2 uA quiescent) for battery applications per datasheet 41391E.
The ICD pins (RB6/RB7 for ICSP) are shared with general-purpose I/O port B - if the application firmware configures these as outputs, in-circuit programming will fail. Either reserve these pins as inputs, or include a programming header that isolates them. The CONFIG words must be set explicitly for the oscillator, watchdog, and brown-out reset - factory default is internal oscillator disabled, which causes the device to appear dead on first power-up per datasheet 41391E.
Route the LCD segment traces away from high-frequency switching nodes (PWM outputs, EUSART, switching regulators) to minimize coupling noise that displays as ghost segments. Keep segment trace lengths below 50 mm where possible and route adjacent segments on different layers to cancel crosstalk. The LCD bias generation network (capacitors on VLCD pins) should be placed within 5 mm of the IC per datasheet 41391E layout guidelines.
Informations de conformité
RoHS compliant and lead-free per Microchip product page. Not AEC-Q100 qualified - the part targets industrial and consumer markets, not automotive. Reach SVHC declaration available from Microchip.
