PIC16LF877AT-I/PT - 8-bit MCU, 14KB Flash, 33 I/O, 44-TQFP | Microchip
Référence : PIC16LF877AT-I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.9 | $9,90 |
| 10 | $9.1 | $91,00 |
| 100 | $7.95 | $795,00 |
| 500 | $6.85 | $3 425,00 |
| 1 000 | $5.95 | $5 950,00 |
PIC16LF877AT-I/PT Présentation
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals (timers, ADC, communication ports) into one IC. PIC microcontrollers sit in the 8-bit MCU hierarchy: microcontroller -> embedded controller -> semiconductor IC, and serve as the "decision makers" in embedded products from coffee makers to industrial drives. The 16F family is Microchip's mid-range 8-bit line with a 14-bit instruction word and 35 single-word instructions, enabling extremely compact code and deterministic interrupt response.
Key features of the PIC16LF877AT-I/PT include: a 20 MHz maximum operating frequency (200 ns instruction cycle), a 10-bit ADC with up to 8 channels, two analog comparators, a Capture/Compare/PWM (CCP) module, enhanced Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), Master Synchronous Serial Port (MSSP) supporting SPI and I2C, two 8-bit timers plus one 16-bit timer, a watchdog timer, in-circuit serial programming (ICSP), and nanoWatt power management with multiple sleep modes.
The 20 MHz core paired with a 14-bit instruction word delivers approximately 5 MIPS of throughput, while the wide 2.0V-5.5V supply range allows direct operation from a single Li-Ion cell, two AA cells, or a regulated 3.3V/5V rail. Internal oscillators and PLL trimming on the LF variant further reduce external component count, simplifying layout for space-constrained designs.
Typical applications include industrial sensor interfaces, motor-control front ends, low-power data acquisition nodes, automotive body electronics (non-safety), and consumer appliance controllers. The 44-pin TQFP exposes up to 33 digital I/O, sufficient for keypad scanning, LCD driving, and parallel bus bridging. Designers value this device for migration paths from older PIC16F877 designs that need lower voltage operation or a tape-and-reel SMD footprint.
When designing with this part, allocate the oscillator and ICSP pins (OSC1/CLK, OSC2/CLKOUT, RB6/PGC, RB7/PGD) on dedicated PCB traces and add a 100 nF decoupling capacitor within 5 mm of VDD. Avoid mapping analog inputs to pins used by the comparator outputs without verifying alternate-function routing, and respect VDD/VSS pairing for the 44-pin TQFP power pins.
Alternatives de remplacement direct pour PIC16LF877AT-I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC16LF877AT-I/PT (même facteur de forme et même empreinte) — différant par Package, Timers, Serial Interfaces, Mounting Type, Operating Temperature.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC16LF877A-I/PT
✅ Remplacement direct✓ En stock
$4.88 / unité
Voir la fiche technique →PIC16F877AT-I/PT
✅ Remplacement direct✓ En stock
$5.42 / unité
Voir la fiche technique →PIC16LF877-04I/PT
✅ Remplacement direct✓ En stock
$6.05 / unité
Voir la fiche technique →PIC16LF877A-I/P
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$5.2 / unité
Voir la fiche technique →PIC16F877A-E/L
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$7.4 / unité
Voir la fiche technique →PIC16LF877AT-I/PT Valeurs maximales et caractéristiques électriques
| Core Architecture | PIC16 8-bit RISC |
| Instruction Word Size | 14-bit |
| Maximum CPU Frequency | 20 MHz |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data RAM | 368 bytes |
| Data EEPROM | 256 bytes |
| Supply Voltage (VDD) | 2.0 V to 5.5 V |
| Number of I/O Pins | 33 |
| ADC | 10-bit, up to 8 channels |
| Timers | 2 x 8-bit, 1 x 16-bit |
| Communication | EUSART, MSSP (SPI/I2C) |
| Température de fonctionnement | -40 C to +85 C (Industrial) |
| Boîtier | 44-pin TQFP (10x10 mm) |
| Type de montage | Surface Mount (Tape & Reel) |
| ICSP / Debug | In-Circuit Serial Programming supported |
| Power-Saving Modes | nanoWatt (Sleep, low-power instructions) |
Configuration des broches de PIC16LF877AT-I/PT
| Broche 1 | MCLR/VPP/RE3 — Master Clear (reset) input / programming voltage / PORTE bit 3 |
| Broche 2 | RA0/AN0 — PORTA bit 0 / analog input channel 0 |
| Broche 3 | RA1/AN1 — PORTA bit 1 / analog input channel 1 |
| Broche 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| Broche 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| Broche 6 | RA4/T0CKI/C1OUT — PORTA bit 4 / Timer0 clock / comparator 1 output |
| Broche 7 | RA5/AN4/SS/C2OUT — PORTA bit 5 / analog 4 / SPI slave select / comparator 2 output |
| Broche 8 | RE0/RD/AN5 — PORTE bit 0 / parallel read / analog 5 |
| Broche 9 | RE1/WR/AN6 — PORTE bit 1 / parallel write / analog 6 |
| Broche 10 | RE2/CS/AN7 — PORTE bit 2 / parallel chip select / analog 7 |
| Broche 11 | VDD — Positive supply (2.0-5.5 V) |
| Broche 12 | VSS — Ground |
| Broche 13 | OSC1/CLKI — Crystal oscillator input / external clock |
| Broche 14 | OSC2/CLKO — Crystal oscillator output / clock out |
| Broche 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| Broche 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| Broche 17 | RC2/CCP1 — PORTC bit 2 / CCP1 (PWM/capture/compare) |
| Broche 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Broche 19 | RD0 — PORTD bit 0 |
| Broche 20 | RD1 — PORTD bit 1 |
| Broche 21 | RD2 — PORTD bit 2 |
| Broche 22 | RD3 — PORTD bit 3 |
| Broche 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Broche 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| Broche 25 | RC6/TX/CK — PORTC bit 6 / EUSART TX / clock |
| Broche 26 | RC7/RX/DT — PORTC bit 7 / EUSART RX / data |
| Broche 27 | RD4 — PORTD bit 4 |
| Broche 28 | RD5 — PORTD bit 5 |
| Broche 29 | RD6/PSP6 — PORTD bit 6 / parallel slave port |
| Broche 30 | RD7/PSP7 — PORTD bit 7 / parallel slave port |
| Broche 31 | VSS — Ground (second tap) |
| Broche 32 | VDD — Positive supply (second tap) |
| Broche 33 | RB0/INT — PORTB bit 0 / external interrupt |
| Broche 34 | RB1 — PORTB bit 1 |
| Broche 35 | RB2 — PORTB bit 2 |
| Broche 36 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| Broche 37 | RB4 — PORTB bit 4 |
| Broche 38 | RB5 — PORTB bit 5 |
| Broche 39 | RB6/PGC — PORTB bit 6 / ICSP clock (ICD clock) |
| Broche 40 | RB7/PGD — PORTB bit 7 / ICSP data (ICD data) |
| Broche 41 | VSS — Ground (third tap) |
| Broche 42 | VDD — Positive supply (third tap) |
| Broche 43 | NC — Not connected (per datasheet) |
| Broche 44 | NC — Not connected (per datasheet) |
Applications typiques
PIC16LF877AT-I/PT convient pour 6 applications: Industrial Sensor Interface Module, Low-Power Battery-Powered Data Logger, Small Appliance Motor Control, Automotive Body Electronics (Non-Safety), Consumer Appliance User Interface Board, RS-232/RS-485 Sensor Network Bridge.
Industrial Sensor Interface Module
PIC16LF877AT-I/PT suits industrial sensor-interface modules where its 10-bit ADC, 8 analog channels, and 33 I/O handle multiple transducer inputs at once. The 2.0-5.5 V VDD range lets the same MCU run from a 24V->5V industrial bus or a 3.3V regulated rail. Designers map analog channels to thermistor or strain-gauge bridges, while the EUSART streams telemetry to a host PLC at 115,200 baud or higher. Its 14 KB Flash accommodates look-up tables for linearization and the 368 B RAM can buffer up to 16 sample frames.
Recommandé
Low-Power Battery-Powered Data Logger
PIC16LF877AT-I/PT is a strong fit for battery-powered data loggers drawing from the nanoWatt sleep modes and 2.0 V minimum VDD. With the ADC and EEPROM on-chip, the MCU can wake, capture, log, and return to deep sleep without external RTC glue. A two-AA alkaline pack delivers ~3.0 V that is right in the supply sweet spot, and the EUSART can dump logs via UART at full 20 MHz speed. The 14 KB Flash stores the state machine and compression routines, while 256 B EEPROM tolerates >1M write cycles for non-volatile event logs.
Recommandé
Small Appliance Motor Control
PIC16LF877AT-I/PT can drive brushed DC or unipolar stepper motor control loops with the CCP module for PWM generation and the 16-bit timer for commutation timing. The 20 MHz core executes a 4 kHz PWM ISR with overhead to spare for current sensing via the 10-bit ADC and overcurrent shutdown via the analog comparator. Industrial-grade temperature range (-40 to +85 C) covers appliance cabinets. The 44-TQFP package fits behind the keypad PCB and the 33 I/O drive multiplexed 7-segment, button matrix, and triac control lines.
Recommandé
Automotive Body Electronics (Non-Safety)
PIC16LF877AT-I/PT fits non-safety automotive body-electronics roles (interior lighting controllers, climate panel modules, seat-position memories) where 44-TQFP and 33 I/O expose enough signals for keypad, LCD, and LIN-style serial links. Industrial temperature grade covers cabin thermal envelopes; the wide supply range tolerates load-dump after-filter rails down to ~4 V. Designers implement UART-based K-line/LIN firmware in 14 KB Flash and use the analog comparator for overcurrent protection of seat motors or window switches.
Recommandé
Consumer Appliance User Interface Board
PIC16LF877AT-I/PT hosts the user-interface board in consumer appliances like coffee machines, washing machines, and microwave ovens. Its 33 I/O drive multiplexed 7-segment displays, button matrices, rotary encoders, and buzzer PWM via the CCP module. The MSSP supports both SPI (for dot-matrix LCD) and I2C (for keypad or temperature sensors) on the same bus pins via Peripheral Pin Select alternatives. With RTC-free operation, the MCU keeps BOM lean while retaining ICSP for in-field firmware updates over a service connector.
Recommandé
RS-232/RS-485 Sensor Network Bridge
PIC16LF877AT-I/PT serves as the bridge MCU for protocol conversion between UART-based sensors and RS-485 multi-drop industrial networks. The EUSART provides the asynchronous serial channel, while the MSSP drives SPI sensors and I2C accessories from a single bus. Its 14 KB Flash implements Modbus RTU command parsers and CRC checks, freeing up the host PLC. The 44-TQFP footprint exposes the dedicated MCLR and ICSP pins for service-port configuration without affecting firmware-loading on the host.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC16LF877AT-I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC16LF877A-I/PT | PIC16F877AT-I/PT | PIC16LF877-04I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-44 (10x10 mm) | TQFP-44 - same | TQFP-44 - same | TQFP-44 - same |
| Core / Frequency | PIC16 8-bit, 20 MHz | PIC16 8-bit, 20 MHz | PIC16 8-bit, 20 MHz | PIC16 8-bit, 4 MHz |
| Program Memory (Flash) | 14 KB | 14 KB | 14 KB | 14 KB |
| Data RAM | 368 B | 368 B | 368 B | 368 B |
| EEPROM | 256 B | 256 B | 256 B | 256 B |
| VDD Range | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 4.0 V to 5.5 V | 2.0 V to 5.5 V |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
Principaux différenciateurs
- Wide-voltage LF silicon (2.0-5.5 V) for battery operation (vs PIC16F877AT-I/PT)
- Full 20 MHz performance at all supply voltages (vs PIC16LF877-04I/PT)
- 44-TQFP package with exposed thermal footprint (vs PIC16LF877A-I/P (PDIP-40))
Notes de conception
Add a 100 nF ceramic decoupling capacitor within 5 mm of every VDD/VSS pair (pin 12/11, 32/31, 42/41). Place a bulk 10 uF aluminum-polymer cap at the board supply rail. The LF variant draws roughly 4 mA active at 20 MHz and <1 uA in deep sleep, so power-rail impedance matters mainly during fast ADC bursts.
Route the MCLR/RA5 pin (pin 1) with a 10 kohm pull-up to VDD and a 100 nF cap to ground for hardware reset; omit the cap if using internal MCLR only. Keep the ICSP/PGD (pin 40) and ICSP/PGC (pin 39) traces short (<50 mm) and away from switching nodes to avoid debugger noise. Use a 4-layer PCB if 20 MHz peripherals are present, otherwise 2-layer with a ground pour suffices.
Do not program the configuration bits to use the internal RC oscillator without checking the application timing margins, as the calibrated accuracy is +/-2%. Analog channels A0-A7 multiplex with PORTA/PORTE pins - leave VREF+/VREF- disconnected when using internal 5 V references to avoid conflict. The CCP1 pin (RC2) is not 5V-tolerant when the device is powered at 2.0 V; clamp signals with a series resistor.
Informations de conformité
RoHS-compliant per Microchip product page 39582C datasheet. Industrial grade (-40C to +85C), not AEC-Q100 qualified; not recommended for automotive safety functions.