PIC18F27Q83-I/SP - 8-bit 64MHz MCU, 128KB Flash, CAN, 28-SPDIP | Microchip
Référence : PIC18F27Q83-I/SP ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $3.85 | $3,85 |
| 10 | $3.45 | $34,50 |
| 100 | $3.05 | $305,00 |
| 500 | $2.71 | $1 355,00 |
| 1 000 | $2.42 | $2 420,00 |
PIC18F27Q83-I/SP Présentation
An 8-bit microcontroller is a microprocessor core with an 8-bit data path, on-chip program memory, RAM, and integrated peripherals optimized for embedded control. Within the broader taxonomy, the PIC18 family sits above baseline PIC10/12/16 and below the PIC24/dsPIC33 16-bit cores, while still employing a 16-bit modified Harvard instruction set that delivers high code density and deterministic interrupt latency for real-time control. The PIC18-Q83 family is one of Microchip's CIP-rich platforms where many peripherals (timers, PWM, ADC, communications, custom logic) can operate without CPU intervention, freeing the core for application logic.
Key features include a 12-bit differential ADC with up to 17 channels, a 5-bit DAC, multiple Zero-Cross Detect modules, configurable logic cells, Complementary Waveform Generator (CWG), three 16-bit Pulse-Width Modulation (PWM) outputs, Hardware Limit Timer (HLT), Windowed Watchdog Timer (WWDT), and an internal 64 MHz high-speed oscillator. The integrated CAN module supports CAN 2.0B active at bit rates up to 1 Mbit/s, making the part a strong fit for distributed industrial nodes.
Typical applications include industrial sensor nodes, HVAC controllers, automotive body and climate modules, building automation gateways, low-cost CAN nodes, and battery-powered instrumentation where deterministic 8-bit control plus fieldbus connectivity is required.
When designing with this part, place a 100 nF decoupling capacitor as close as possible to each VDD/VSS pair and keep the ICSP/PGD/PGC traces short to preserve in-circuit debug stability. For CAN bus termination, add a 120 ohm resistor at each end of the bus, never at the node itself.
This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18-Q83 and PIC18-Q84 families, and practical design notes not found in the manufacturer datasheet alone, giving you a single decision-ready reference for sourcing PIC18F27Q83-I/SP.
Alternatives de remplacement direct pour PIC18F27Q83-I/SP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC18F27Q83-I/SP (même facteur de forme et même empreinte) — différant par Package, ADC, Mounting Type, Program Memory (Flash), Operating Temperature.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC18F27Q84-I/SP
✅ Remplacement direct✓ En stock
$2.2 / unité
Voir la fiche technique →PIC18F26Q84-I/SP
✅ Remplacement direct✓ En stock
$1.95 / unité
Voir la fiche technique →PIC18F27Q43-I/SP
✅ Remplacement direct✓ En stock
$2.46 / unité
Voir la fiche technique →PIC18F26Q43-I/SP
✅ Remplacement direct✓ En stock
$1.74 / unité
Voir la fiche technique →PIC18F25Q43-I/SP
✅ Remplacement direct✓ En stock
$1.72 / unité
Voir la fiche technique →PIC18F27K42-I/SP
✅ Remplacement direct✓ En stock
$2.62 / unité
Voir la fiche technique →PIC18F27Q83-I/SP Valeurs maximales et caractéristiques électriques
| Core | PIC18 8-bit |
| Maximum CPU Frequency | 64 MHz |
| Program Memory (Flash) | 128 KB |
| Data SRAM | 13 KB |
| Data EEPROM | 1 KB |
| Boîtier | 28-SPDIP (Skinny Plastic DIP, through-hole) |
| Nombre de broches | 28 |
| I/O Pins | 25 |
| ADC | 12-bit differential, up to 17 channels |
| DAC | 5-bit |
| CAN | CAN 2.0B active, up to 1 Mbit/s |
| PWM | 3x 16-bit PWM channels |
| Operating Voltage (VDD) | 2.3 V to 5.5 V |
| Température de fonctionnement | -40 C to +85 C (Industrial, -I) |
| Type de montage | Through-Hole (THT) |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
Configuration des broches de PIC18F27Q83-I/SP
| Broche 1 | MCLR/VPP/RE3 — Master Clear (reset) input or ICSP programming voltage; also functions as digital input RE3 |
| Broche 2 | RA0 — Digital I/O / analog input |
| Broche 3 | RA1 — Digital I/O / analog input |
| Broche 4 | RA2 — Digital I/O / analog input |
| Broche 5 | RA3 — Digital I/O / analog input |
| Broche 6 | RA4 — Digital I/O / analog input |
| Broche 7 | VDD — Positive supply voltage (2.3 V to 5.5 V) |
| Broche 8 | VSS — Ground reference |
| Broche 9 | RA5 — Digital I/O / analog input |
| Broche 10 | RA6 — Digital I/O / analog input |
| Broche 11 | RC0 — Digital I/O |
| Broche 12 | RC1 — Digital I/O / CCP2 |
| Broche 13 | RC2 — Digital I/O / CCP1 |
| Broche 14 | RC3 — Digital I/O / SCL |
| Broche 15 | RC4 — Digital I/O / SDA |
| Broche 16 | RC5 — Digital I/O |
| Broche 17 | RC6 — Digital I/O / CANTX |
| Broche 18 | RC7 — Digital I/O / CANRX |
| Broche 19 | VSS — Ground reference |
| Broche 20 | VDD — Positive supply voltage (2.3 V to 5.5 V) |
| Broche 21 | RB0 — Digital I/O / analog input / interrupt-on-change |
| Broche 22 | RB1 — Digital I/O / analog input / interrupt-on-change |
| Broche 23 | RB2 — Digital I/O / analog input / interrupt-on-change |
| Broche 24 | RB3 — Digital I/O / analog input / interrupt-on-change |
| Broche 25 | RB4 — Digital I/O / interrupt-on-change |
| Broche 26 | RB5 — Digital I/O / interrupt-on-change / CCP3 |
| Broche 27 | RB6 — Digital I/O / PGC (ICSP clock) |
| Broche 28 | RB7 — Digital I/O / PGD (ICSP data) |
Applications typiques
PIC18F27Q83-I/SP convient pour 6 applications: Industrial CAN Bus Sensor Nodes, Automotive Body and Comfort Modules, Building Automation Gateways, Battery-Powered Instrumentation, HVAC Climate Control Units, Low-Cost Fieldbus Endpoint Nodes.
Industrial CAN Bus Sensor Nodes
The PIC18F27Q83-I/SP fits industrial CAN bus sensor nodes because its on-chip CAN 2.0B controller supports standard 11-bit and extended 29-bit identifiers at bit rates up to 1 Mbit/s without an external protocol IC, reducing BOM cost. With 128 KB Flash and 13 KB SRAM, the device can run CANopen or J1939-style stacks with room for application logic. Place the MCU between an external MCP2551/MCP2562 CAN transceiver and the sensor front-end, and use the integrated 12-bit differential ADC for ratiometric sensor readings directly off bridge outputs. The -40 C to +85 C industrial temperature grade suits factory-floor deployments.
Recommandé
Automotive Body and Comfort Modules
In automotive body and comfort modules such as HVAC door panels, mirror controllers, and seat adjusters, the PIC18F27Q83-I/SP delivers enough CPU bandwidth at 64 MHz to drive multiple LIN-style sub-buses alongside a CAN backbone. The 12-bit ADC and 5-bit DAC can read potentiometers and drive small actuator references, while the three 16-bit PWM channels run LED dimming or motor speed control. The integrated CAN module lets a single MCU talk to the body controller without an external protocol IC. Designers should pair the part with a robust TVS protection array on the bus and use the watchdog window mode for safety compliance.
Recommandé
Building Automation Gateways
The PIC18F27Q83-I/SP suits building automation gateways that bridge low-speed sensor networks to a CAN backbone, since the on-chip CAN module plus UART/SPI/I2C peripherals let the MCU aggregate Modbus RTU, I2C sensor, or SPI device traffic. The 128 KB Flash fits BACnet or vendor-specific gateway firmware, and the 13 KB SRAM comfortably buffers concurrent Modbus and CAN frames. Use the dedicated CAN TX/RX pins (RC6/RC7) routed straight to an isolated CAN transceiver such as the MCP2562 with a small digital isolator for 3 kV bus isolation.
Recommandé
Battery-Powered Instrumentation
Battery-powered instrumentation such as portable data loggers or remote telemetry units benefits from the PIC18F27Q83-I/SP because the PIC18-Q83 supports multiple low-power sleep modes down to the nanoampere range and integrates a low-power 32 kHz auxiliary oscillator for RTC duty cycling. The 128 KB Flash accommodates several days of compressed local logging, while the 1 KB EEPROM stores calibration constants without wearing the Flash. Designers can wake the device from CAN activity, perform a 12-bit ADC scan, transmit the result, and return to sleep, achieving average current budgets below 1 mA on a 3.6 V Li-SoCl2 cell.
Recommandé
HVAC Climate Control Units
The PIC18F27Q83-I/SP works well in HVAC climate control units because its three 16-bit PWM channels can drive triac-fired heater elements or variable-speed fans directly, while the 12-bit differential ADC reads thermistor bridges with hardware averaging. The CAN module lets the unit report status to a central building controller, and the 5-bit DAC drives analog setpoint panel indicators. Use the CWG (Complementary Waveform Generator) for dead-band control of half-bridge drivers, eliminating CPU cycle overhead. Operate at 5 V to maximize noise margin on long analog runs.
Recommandé
Low-Cost Fieldbus Endpoint Nodes
For low-cost CAN-based fieldbus endpoints in factory automation, the PIC18F27Q83-I/SP delivers a deterministic 8-bit core, on-chip CAN, and 25 I/O pins at a price point well below 32-bit ARM alternatives. The integrated CIPs let the part toggle outputs, scan ADCs, and reply to CAN frames without waking the main CPU, freeing cycles for application code. Stack any number of these nodes on a single CAN bus with 120 ohm termination at both ends of the trunk. The 28-SPDIP package simplifies hand-soldered prototypes and educational kits, accelerating bring-up.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC18F27Q83-I/SP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC18F27Q84-I/SP | PIC18F26Q84-I/SP | PIC18F27Q43-I/SP | PIC18F26Q43-I/SP | PIC18F25Q43-I/SP | PIC18F27K42-I/SP |
|---|---|---|---|---|---|---|---|
| Package | 28-SPDIP | 28-SPDIP - same | 28-SPDIP - same | 28-SPDIP - same | 28-SPDIP - same | 28-SPDIP - same | 28-SPDIP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Core | PIC18 8-bit @ 64 MHz | PIC18 8-bit @ 64 MHz | PIC18 8-bit @ 64 MHz | PIC18 8-bit @ 64 MHz | PIC18 8-bit @ 64 MHz | PIC18 8-bit @ 64 MHz | PIC18 K42 8-bit @ 64 MHz |
| Flash Program Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 32 KB | 128 KB |
| Data SRAM | 13 KB | 13 KB | 13 KB | 13 KB | 13 KB | 2 KB | 8 KB |
| Data EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| CAN Module | CAN 2.0B, 1 Mbit/s | CAN FD, 8 Mbit/s data phase | CAN FD, 8 Mbit/s data phase | None | None | None | None |
| ADC Resolution | 12-bit, up to 17 channels | 12-bit, up to 17 channels | 12-bit, up to 17 channels | 12-bit, up to 17 channels | 12-bit, up to 17 channels | 12-bit, up to 17 channels | 12-bit, up to 24 channels |
| Operating Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
Principaux différenciateurs
- On-chip CAN 2.0B controller (vs PIC18F27Q43-I/SP)
- Forward path to CAN FD (vs PIC18F27Q84-I/SP)
- Higher Flash density vs Q43 lower pin-count (vs PIC18F26Q43-I/SP)
Notes de conception
Place a 100 nF decoupling capacitor as close as possible to each VDD/VSS pair (pins 7/8 and 19/20 on the 28-SPDIP). Add a bulk 1 uF to 10 uF tantalum or ceramic capacitor near the package to handle transient current spikes when the CPU wakes from sleep into full-speed ADC scanning. For battery-powered designs, use the PIC18-Q83's nanoampere sleep modes plus a 32 kHz auxiliary oscillator to keep average current below 1 mA.
Keep the ICSP traces PGD (RB7) and PGC (RB6) shorter than 50 mm total, route them away from the CAN bus traces, and place a 4.7 kohm pull-up on MCLR (pin 1). If the design must tolerate production-line programming without removing the part, dedicate the ICSP pins and do not reuse them for high-impedance analog inputs, or your debugger may false-trigger on noise.
Do not omit the 120 ohm CAN bus termination resistors at each end of the bus trunk - they are required for reliable high-speed CAN signaling. Do not connect the on-chip CAN module directly to the bus without a transceiver such as the MCP2551 or MCP2562; the on-chip module handles protocol only, never physical layer. Finally, when migrating from PIC18F27Q83 to PIC18F27Q84 in the same 28-SPDIP footprint, verify peripheral pinout changes at the schematic level because the Q84 adds CAN FD that shifts some alternate pin functions.
Informations de conformité
Industrial temperature grade -40 C to +85 C per Microchip datasheet; AEC-Q100 is not specified for this part. RoHS and REACH compliance per Microchip product page.
