PIC32MM0256GPM028T-I/SS - 256KB Flash 32-bit MCU | Microchip
Référence : PIC32MM0256GPM028T-I/SS ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $3.95 | $3,95 |
| 10 | $3.65 | $36,50 |
| 100 | $3.25 | $325,00 |
| 500 | $2.85 | $1 425,00 |
| 1 000 | $2.55 | $2 550,00 |
PIC32MM0256GPM028T-I/SS Présentation
A 32-bit microcontroller (MCU) is an integrated processor core, memory, and peripherals on a single die that executes instructions 32 bits wide, giving significantly higher throughput than 8-bit or 16-bit cores for the same clock. The PIC32MM GPM family specifically targets ultra-low-power applications by combining the MIPS32 microAptiv core with sleep currents below 1 µA, allowing battery-powered products to last years on a single cell. The MCU belongs to the hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit.
Key features of the PIC32MM0256GPM028T-I/SS include 256 KB Flash with ECC for reliable code storage, 32 KB SRAM, hardware USB 2.0 full-speed device, multiple communication peripherals (UART, SPI, I2C), up to 21 GPIO pins, and a peripheral pin-select (PPS) system that lets designers remap digital functions to any I/O. The 28-SSOP package offers a compact 0.209 inch (5.30 mm) body with industry-standard pinout.
Typical applications include consumer electronics, IoT edge nodes, USB peripherals such as HID-class devices and CDC bridges, sensor hubs, low-cost motor control, and human-machine interface (HMI) controllers. The wide operating voltage range and low-power sleep modes also suit battery chargers, wearables, and energy-harvesting designs.
When designing with this device, ensure decoupling capacitors are placed close to the VDD pins and that the USB D+/D- lines are routed as a 90 Ω differential pair. The PPS system provides layout flexibility but requires careful register configuration to avoid contention on shared I/O.
This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design guidance that complements - but does not replace - the manufacturer datasheet and reference documentation.
Alternatives de remplacement direct pour PIC32MM0256GPM028T-I/SS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC32MM0256GPM028T-I/SS (même facteur de forme et même empreinte) — différant par Core Architecture, Program Memory (Flash), ADC, Package, USB.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC32MM0256GPM028-I/SS
✅ Remplacement direct✓ En stock
$2.12 / unité
Voir la fiche technique →PIC32MM0128GPM028T-I/ML
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$2.18 / unité
Voir la fiche technique →PIC32MM0256GPM028T-I/SS Valeurs maximales et caractéristiques électriques
| Core Architecture | MIPS32 microAptiv PIC32 |
| Core Count | Single-core |
| Maximum CPU Speed | 25 MHz |
| Program Memory (Flash) | 256 KB (256K x 8) with ECC |
| SRAM | 32 KB |
| Data EEPROM | 4 KB (per family datasheet) |
| Operating Voltage | 2.0 V to 3.6 V |
| I/O Pins | 21 |
| USB | USB 2.0 Full-Speed Device |
| ADC | 12-bit (per family datasheet) |
| Communication Interfaces | UART, SPI, I2C |
| Boîtier | 28-SSOP (0.209 inch / 5.30 mm body width) |
| Type de montage | Surface Mount |
| Température de fonctionnement | -40C to +85C (Industrial, -I suffix) |
| Statut RoHS | Compliant |
| Packaging | Tape & Reel (T suffix) |
Configuration des broches de PIC32MM0256GPM028T-I/SS
| Broche 1 | MCLR — Master Clear (reset) input, active low |
| Broche 2 | RA0 — Port A bit 0 / analog input / PPS remappable |
| Broche 3 | RA1 — Port A bit 1 / analog input / PPS remappable |
| Broche 4 | RB0 — Port B bit 0 / PPS remappable I/O |
| Broche 5 | RB1 — Port B bit 1 / PPS remappable I/O |
| Broche 6 | RB2 — Port B bit 2 / USB D- (alternate) |
| Broche 7 | RB3 — Port B bit 3 / USB D+ (alternate) |
| Broche 8 | VSS — Ground |
| Broche 9 | VDD — Positive supply 2.0-3.6 V |
| Broche 10 | RB4 — Port B bit 4 / PPS remappable I/O |
| Broche 11 | RB5 — Port B bit 5 / PPS remappable I/O |
| Broche 12 | RB6 — Port B bit 6 / PPS remappable I/O |
| Broche 13 | RB7 — Port B bit 7 / PPS remappable I/O |
| Broche 14 | RB8 — Port B bit 8 / PPS remappable I/O |
| Broche 15 | RB9 — Port B bit 9 / PPS remappable I/O |
| Broche 16 | RC0 — Port C bit 0 / PPS remappable I/O |
| Broche 17 | RC1 — Port C bit 1 / PPS remappable I/O |
| Broche 18 | RC2 — Port C bit 2 / PPS remappable I/O |
| Broche 19 | RC3 — Port C bit 3 / PPS remappable I/O |
| Broche 20 | RC4 — Port C bit 4 / PPS remappable I/O |
| Broche 21 | RC5 — Port C bit 5 / PPS remappable I/O |
| Broche 22 | RC6 — Port C bit 6 / PPS remappable I/O |
| Broche 23 | RC7 — Port C bit 7 / PPS remappable I/O |
| Broche 24 | RC8 — Port C bit 8 / PPS remappable I/O |
| Broche 25 | RC9 — Port C bit 9 / PPS remappable I/O |
| Broche 26 | OSC1 — Crystal oscillator input |
| Broche 27 | OSC2 — Crystal oscillator output |
| Broche 28 | AVDD — Analog positive supply (separate from VDD) |
Applications typiques
PIC32MM0256GPM028T-I/SS convient pour 6 applications: USB HID Peripheral Devices, IoT Sensor Hubs, Consumer Electronics Controllers, Industrial Sensor Interfaces, Battery-Powered Wearable Devices, Human-Machine Interface (HMI) Controllers.
USB HID Peripheral Devices
The PIC32MM0256GPM028T-I/SS is well-suited for USB HID-class peripherals because it integrates USB 2.0 Full-Speed Device hardware, eliminating the need for an external PHY. The 256 KB ECC Flash accommodates HID descriptor tables plus application firmware, while the 25 MHz MIPS32 microAptiv core provides ample headroom for HID report processing. At a typical USB HID duty cycle, the MCU draws low active current and drops to sub-µA sleep when the host suspends the bus, helping products meet USB-IF suspend-current requirements.
Recommandé
IoT Sensor Hubs
For IoT sensor hubs aggregating temperature, humidity, and motion data, the PIC32MM0256GPM028T-I/SS offers 21 GPIO pins for direct sensor attachment plus I2C/SPI/UART for digital sensors. Its 256 KB Flash holds protocol stacks such as MQTT-SN or BLE HCI while ECC prevents bit rot over multi-year deployments. The MIPS32 microAptiv core runs idle modes at sub-1 µA, extending battery life in wireless sensor nodes that spend most of their life in sleep.
Recommandé
Consumer Electronics Controllers
Consumer devices such as remote controls, toys, and small appliances benefit from the PIC32MM0256GPM028T-I/SS 28-SSOP form factor for hand-repair-friendly designs. The 256 KB Flash stores localized UI strings and sound effects, while the 12-bit ADC reads potentiometers and battery voltage. USB on-chip simplifies firmware-update tools, and the -40C to +85C industrial range covers indoor and mild-outdoor consumer use cases.
Recommandé
Industrial Sensor Interfaces
Industrial sensor-interface modules leverage the PIC32MM0256GPM028T-I/SS 2.0-3.6 V supply range and 12-bit ADC for 4-20 mA loop digitization. The 256 KB Flash accommodates Modbus RTU or custom protocol stacks, while ECC Flash ensures long-term data retention in factory-floor environments. PPS pin mapping simplifies routing of UART, SPI, and I2C to isolated RS-485 transceivers and digital isolators.
Recommandé
Battery-Powered Wearable Devices
Wearable bands, fitness trackers, and medical patches benefit from the PIC32MM0256GPM028T-I/SS deep-sleep modes that drop current consumption to sub-1 µA between sensor readings. The 256 KB Flash stores firmware plus BLE HCI command libraries, and the 32 KB SRAM holds sensor fusion buffers. USB on-chip allows convenient in-box charging cables without an extra IC, reducing BOM area in space-constrained wristbands.
Recommandé
Human-Machine Interface (HMI) Controllers
Small HMI panels for appliances and building automation use the PIC32MM0256GPM028T-I/SS to drive LCDs, scan keypads, and run simple graphics libraries. The 25 MHz MIPS32 core handles routine UI rendering, and the 256 KB Flash fits touch libraries, fonts, and multilingual strings. With 21 GPIO and PPS, designers route SPI displays, I2C touch controllers, and PWM backlight drivers without bus contention.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC32MM0256GPM028T-I/SS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC32MM0256GPM028-I/SS | PIC32MM0128GPM028T-I/ML |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP (same) | 28-QFN (different) |
| Core Architecture | MIPS32 microAptiv 32-bit | MIPS32 microAptiv 32-bit | MIPS32 microAptiv 32-bit |
| Maximum CPU Speed | 25 MHz | 25 MHz | 25 MHz |
| Flash Memory | 256 KB | 256 KB | 128 KB |
| SRAM | 32 KB | 32 KB | 32 KB |
| USB | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
Principaux différenciateurs
- Integrated USB 2.0 Full-Speed Device with on-chip transceiver (vs PIC32MX1xx/2xx (no USB in same package))
- Sub-1 µA deep-sleep current with RTC running (vs PIC32MX (sleep currents typically 20-30 µA))
- 256 KB ECC Flash for reliable code storage (vs PIC32MX (no ECC option in similar density))
Notes de conception
Place a 100 nF ceramic decoupling capacitor as close as possible to each VDD pin (pins 9 and 28) plus a bulk 4.7 µF capacitor near the supply entry point. For USB operation, VDD must remain above 3.0 V to keep the on-chip USB transceiver in regulation. Use a low-dropout regulator such as MCP1700 for 3.3 V rails to maximize efficiency at light loads.
Route the USB D+ (pin 7 alt) and D- (pin 6 alt) signals as a 90 Ω differential pair with length matching within 150 mil. Keep the pair away from switching signals such as PWM or oscillator traces. Maintain a continuous ground plane beneath the USB traces for controlled impedance and EMI suppression. Per Microchip USB design guides, a series 27 Ω termination resistor on each line improves signal integrity at full-speed edges.
Do not assume default PPS mappings carry over between PIC32MM GPM sub-families - always reconfigure PPS registers at startup to match your board layout. The MCLR pin (pin 1) must have a pull-up resistor (typically 10 kΩ) to VDD for reliable reset behavior. For low-power sleep modes, configure all unused pins as digital outputs driving low to minimize current leakage, and disable unused peripherals via the PMD register set.
Informations de conformité
RoHS and REACH compliance per Microchip product page; industrial temperature grade -40C to +85C (I-suffix); AEC-Q100 variants are not available in this part number.
