XC2C64A-7QFG48C - 64-Macrocell 1.8V CPLD | AMD
Référence : XC2C64A-7QFG48C ✗ Fin de vieXC2C64A-7QFG48C Présentation
A CPLD is a programmable logic device that connects combinational and sequential logic blocks through a programmable interconnect. The CoolRunner-II architecture belongs to the broader hierarchy of programmable logic devices, alongside FPGAs, and is commonly used for glue logic, interface adaptation, control sequencing, and compact system-level logic. Compared with a large FPGA, the XC2C64A provides a smaller logic capacity with relatively simple configuration and predictable device organization.
Key features include 64 macrocells, 37 user I/O, 4.6 ns pin-to-pin logic delay, and quiescent current as low as 15 A. The device uses 0.18 µm CMOS technology and supports a 1.8 V operating supply. Its in-system programmable architecture allows a circuit to be configured or reconfigured without removing the package from the assembled PCB, which supports production programming, prototype updates, and field-configurable logic.
The CoolRunner-II implementation provides dedicated macrocell resources for registered and combinational functions. Its documented 159 MHz speed classification and 4.6 ns pin-to-pin delay suit moderate-frequency control, bus, and interface designs. Because the XC2C64A is a legacy programmable-logic product, designers should verify the programmed bitstream, I/O standards, system-level timing, and toolchain support against the current AMD design flow before committing a new production design.
Typical applications include low-speed communications interface control, industrial automation modules, embedded control systems, automotive electronic subsystems, consumer equipment, and compact peripheral adapters. The 48-pin QFN exposed-pad package also makes the device suitable for space-constrained boards where a larger plastic quad flat package would be undesirable. Thermal performance depends on the exposed-pad layout, copper area, and the aggregate switching activity of the programmed logic.
For PCB implementation, use the package drawing and pin-description table in the DS311 manufacturer datasheet for land patterns and signal assignments. Connect the exposed pad to the appropriate ground plane, place decoupling capacitors close to the supply pins, and keep programming and configuration interfaces away from sensitive analog or high-speed clock routing. Validate signal integrity with the actual board stack-up and the selected I/O standard.
This product page consolidates the manufacturer specifications, package details, application guidance, and traceable replacement analysis for the XC2C64A-7QFG48C. It is intended to help engineers evaluate the device, confirm the exact ordering code, and plan a technically compatible design or migration path.
Alternatives de remplacement direct pour XC2C64A-7QFG48C — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec XC2C64A-7QFG48C (même facteur de forme et même empreinte) — différant par Package, Device Type, Lead-Free Status, Programmable Type, RoHS Status.
XC2C64A-7QFG48I
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →XC2C64A-6QFG48C
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
XC2C64A-5QFG48C
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →XC2C64A-7QFG48C Valeurs maximales et caractéristiques électriques
| Programmable Type | In-System Programmable |
| Device Type | CoolRunner-II CPLD |
| Macrocell Count | 64 macrocells |
| Logic Gate Capacity | Approximately 1.5K gates |
| Maximum Operating Frequency | 159 MHz |
| Pin-to-Pin Logic Delay | 4.6 ns |
| User I/O Count | 37 I/O |
| Tension d'alimentation | 1.8 V |
| Process Technology | 0.18 µm CMOS |
| Courant de repos | As low as 15 A |
| Boîtier | 48-pin QFN with exposed pad, 7 mm × 7 mm |
| Type de montage | Surface mount |
| Temperature Grade | Commercial |
| Lead-Free Status | Lead free |
| Statut RoHS | RoHS compliant |
| Programming Architecture | Multi-site programmable |
| Package Dimensions | 7 mm × 7 mm |
Guide de configuration des broches du XC2C64A-7QFG48C 7 mm × 7 mm
Configuration des broches du XC2C64A-7QFG48C (boîtier 7 mm × 7 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour XC2C64A-7QFG48C.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
XC2C64A-7QFG48C convient pour 6 applications: Industrial Automation Control, Embedded System Interface Control, Automotive Electronic Subsystems, Communications Interface Adaptation, Consumer Peripheral Adapters, Programmable Logic Prototyping.
Industrial Automation Control
The XC2C64A-7QFG48C fits compact industrial control modules that coordinate sensors, actuators, status indicators, and communications interfaces. Its 64 macrocells provide enough logic for state machines, timing controls, and bus-signal adaptation, while the 1.8 V supply supports modern low-voltage sensor and controller ecosystems. The 4.6 ns pin-to-pin delay and 159 MHz speed classification are useful where control paths require deterministic behavior. For a production design, verify the commercial temperature range against the enclosure environment and evaluate the XC2C64A-7QFG48I when industrial qualification is required.
Recommandé
Embedded System Interface Control
The XC2C64A-7QFG48C is useful when an embedded system needs dedicated programmable logic for protocol conversion, address decoding, latch control, or interrupt coordination. Sixty-four macrocells can implement moderate combinational and sequential functions without occupying the main application processor. Its 37 user I/O provide practical connectivity in a compact QFN-48 package, and its 1.8 V operation aligns with low-voltage embedded controllers. Validate every setup-and-hold interval against the connected processor, configure unused pins consistently, and use the DS311 timing tables rather than relying only on the 159 MHz headline frequency.
Recommandé
Automotive Electronic Subsystems
The XC2C64A-7QFG48C can support legacy automotive electronic subsystems requiring compact logic for sensor conditioning, actuator sequencing, diagnostic routing, or communication control. Its 64 macrocells and 37 user I/O are suitable for moderate control logic, while its low quiescent current can benefit power-constrained implementations. Vehicle use requires careful review of the required temperature grade, qualification scope, environmental stresses, and functional-safety expectations; the industrial XC2C64A-7QFG48I is the relevant family option when the commercial grade is unsuitable. No automotive qualification should be inferred solely from the family name or application suitability.
Recommandé
Communications Interface Adaptation
The XC2C64A-7QFG48C is suited to low-to-moderate-speed communications adapters that need selectable logic levels, framing assistance, FIFO control, or parallel-to-serial signal conversion. Its programmable interconnect allows protocol-specific routing without changing the PCB, and its 4.6 ns pin-to-pin delay supports high relative timing margin compared with slower CPLD grades. The 48-pin QFN footprint supports compact interface modules, although exposed-pad layout and ground return paths require careful PCB planning. Confirm whether the selected legacy programming flow and bitstream-generation tools remain available for the product's maintenance life.
Recommandé
Consumer Peripheral Adapters
The XC2C64A-7QFG48C can implement compact glue logic for legacy consumer peripherals, including configuration sequencing, display control, button decoding, status indication, and data-routing functions. Sixty-four macrocells provide meaningful capacity without requiring a larger FPGA, while the 1.8 V supply and 37 user I/O fit many low-voltage boards. In a cost-sensitive product, compare the timing capability of the -7 grade against the lower-speed XC2C64A-5QFG48C to avoid paying for unnecessary performance. Confirm package availability, programming-tool support, and lifecycle requirements before finalizing a new consumer design.
Recommandé
Programmable Logic Prototyping
The XC2C64A-7QFG48C supports prototypes requiring moderate logic density, repeated design revisions, and stable board-level reconfiguration. Its in-system programming architecture allows a programmed configuration to be updated without removing the device, making it useful for control logic, test fixtures, and interface experiments. The 64-macrocell resource count and 159 MHz speed classification support moderately complex digital functions, while the 48-pin QFN package keeps the prototype compact. Designers should preserve a documented programming and pin-assignment baseline so production fixtures can reproduce the verified configuration and any late board changes.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour XC2C64A-7QFG48C — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | XC2C64A-7QFG48I | XC2C64A-6QFG48C | XC2C64A-5QFG48C |
|---|---|---|---|---|
| Package | QFN-48 with exposed pad | QFN-48 with exposed pad | QFN-48 with exposed pad | QFN-48 with exposed pad |
| Brand | AMD | AMD | AMD | AMD |
| Macrocell Count | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells |
| Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Speed Grade | -7, 159 MHz | -7, 159 MHz | -6 | -5 |
| Temperature Grade | Commercial | Industrial | Commercial | Commercial |
| Process Technology | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS |
| Programmable Type | In-System Programmable | In-System Programmable | In-System Programmable | In-System Programmable |
Principaux différenciateurs
- Highest listed speed grade in the drop-in set (vs XC2C64A-5QFG48C)
- Commercial-temperature ordering configuration (vs XC2C64A-7QFG48I)
- Same core and footprint with direct family interchangeability (vs XC2C64A-6QFG48C)
Notes de conception
Use the QFG48 land pattern and exposed-pad geometry from the DS311 manufacturer datasheet. The exposed pad requires a carefully sized thermal-via field and a low-impedance connection to the selected ground plane. Check solder-assembly capability, copper balance, and the effect of the thermal pad on the board's downstream manufacturing and inspection processes.
Place the device's supply decoupling capacitors adjacent to the relevant power pins and keep the return path short. The specified 1.8 V supply applies to the core and supported interfaces, but external I/O standards, pull networks, and connected devices must also be checked for voltage compatibility. Avoid routing programming or configuration signals through long paths adjacent to switching nodes.
Build timing closure from the DS311 setup-and-hold specifications rather than the 159 MHz headline frequency alone. Include external-device timing, board skew, loading, and clock uncertainty in the analysis. If the XC2C64A-5QFG48C or XC2C64A-6QFG48C is substituted, rerun the critical-path analysis because the lower speed grade reduces timing margin.
Do not substitute a device with a different QFG package without a PCB redesign, even when its macrocell count is similar. The XC2C64A-7VQG44I and XC2C64A-7VQG44C use a different 44-pin footprint, while XC2C64A-7CPG56C and XC2C64A-7CPG56I use a 56-pin footprint. Verify the complete ordering code, pin count, exposed-pad pattern, and speed-grade suffix before procurement.
Estimated: with a 1.8 V core supply, 15 A quiescent current, and 10,000 I/O transitions per second, dynamic output current is approximately 0.3 mA; core dissipation is therefore roughly 0.00054 W before static output loading and internal activity. Actual total device power is higher and depends on the programmed logic and I/O switching rate, so thermal validation should use the maximum intended activity and the final PCB thermal model.
Informations de conformité
The part listing identifies the XC2C64A-7QFG48C as lead free and RoHS compliant. No REACH, halogen-free, conflict-minerals, or AEC-Q100 claim was established for this exact ordering code.