XC7Z014S-2CLG484I - 65K Zynq SoC with Cortex-A9 | AMD
Référence : XC7Z014S-2CLG484I ✓ ActifXC7Z014S-2CLG484I Présentation
A Zynq SoC is a system-on-chip that combines an ARM processing system with FPGA programmable logic. Its product hierarchy runs from FPGA and SoC to adaptive SoC and embedded processing. The processing system executes operating systems and control software, while the programmable logic implements parallel data paths, hardware accelerators, custom interfaces, and time-critical signal processing. This division allows one device to consolidate functions that might otherwise require a separate microcontroller and FPGA.
The XC7Z014S uses a 28 nm process and provides 200 I/O according to the product listing. Its single Cortex-A9 processor includes the Cortex-A9 MPCore architecture and CoreSight debugging, while the Artix-7 logic fabric provides 65K logic cells. The -2 speed designation corresponds to the listed 766 MHz processor operating point. Its CLG484 package also supports DDR memory interfaces and other programmable-logic I/O needed by embedded control, communications, and industrial systems.
The integrated architecture permits hardware acceleration without a separate FPGA-to-SoC interconnect. Parallel functions can execute in programmable logic while the ARM core manages control flow, operating systems, or network protocols. This can reduce board area and latency, although firmware, Vivado implementation, hardware/software partitioning, DDR layout, and clocking must be designed as one coherent system. Pin assignments and power sequencing should follow the AMD Zynq-7000 package documentation and pinout files.
Typical uses include industrial machine control, factory automation, networked embedded controllers, sensor and vision preprocessing, communications gateways, and test equipment. The Cortex-A9 side is appropriate for Linux or RTOS-based supervisory control, while programmable logic can accelerate data acquisition, protocol conversion, motor-control algorithms, or custom video and communications pipelines. The 200-I/O count supports integration of DDR, transceivers, control signals, and external memory.
Power planning is central to a 484-CSPBGA design. The processor, programmable logic, and high-speed memory interfaces can create substantial dynamic and thermal loads even though the part is not a conventional linear power device. Use the AMD data sheet for recommended rails, sequencing, decoupling, and operating limits. Place bypass capacitors at the supply pins, route power and ground planes carefully, and provide thermal copper around the BGA while avoiding via stubs in sensitive nets.
This page combines the manufacturer data-sheet link, exact device specifications, package details, practical Zynq design guidance, and clearly qualified same-package alternatives. It also distinguishes speed and temperature-grade options so engineers can identify a potential hardware replacement without mistaking it for a complete system-level equivalence.
Alternatives de remplacement direct pour XC7Z014S-2CLG484I — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec XC7Z014S-2CLG484I (même facteur de forme et même empreinte) — différant par Device Type, Package, Processor Frequency, Programmable Logic Cells, Temperature Grade.
XC7Z014S-2CLG484C
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
XC7Z014S-1CLG484I
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →XC7Z014S-1CLG484C
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →XC7Z014S-1CLG484E
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
XC7Z014S-2CLG484E
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →XC7Z014S-2CLG484I Valeurs maximales et caractéristiques électriques
| Device Type | Zynq-7000 SoC with Artix-7 FPGA |
| Processing System | Single ARM Cortex-A9 MPCore with CoreSight |
| Processor Frequency | 766 MHz |
| Programmable Logic | Artix-7 FPGA |
| Logic Cells | 65K cells |
| Process Technology | 28 nm |
| I/O Count | 200 I/O |
| Boîtier | 484-CSPBGA (19 mm x 19 mm) |
| Nombre de broches | 484 pins |
| Speed Grade | -2 |
| Temperature Grade | I suffix |
| CoreSight Support | Yes |
| Type de montage | Surface Mount |
| Packaging Format | Tray |
| Statut RoHS | Compliant |
| Automotive Qualification | Not indicated |
| Core Supply Voltage | 1 V |
Guide de configuration des broches du XC7Z014S-2CLG484I 484-cspbga (19 mm x 19 mm)
Configuration des broches du XC7Z014S-2CLG484I (boîtier 484-cspbga (19 mm x 19 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour XC7Z014S-2CLG484I.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
XC7Z014S-2CLG484I convient pour 6 applications: Industrial Machine Control, Factory Automation Gateway, Vision and Sensor Preprocessing, Communications Gateway, Networked Sensor Controller, Programmable Test and Measurement.
Industrial Machine Control
The XC7Z014S-2CLG484I suits industrial machine controllers that divide supervisory logic from deterministic hardware functions. Its single 766 MHz Cortex-A9 can run control software, communications stacks, or an RTOS, while the 65K-cell Artix-7 fabric handles encoder capture, pulse timing, or parallel signal conditioning. The 200 available I/O support isolated field-bus interfaces, digital I/O, and external memory. Placing these functions in one SoC reduces inter-device latency and board area, although the design must preserve clean power rails and complete Vivado timing analysis.
Recommandé
Factory Automation Gateway
The XC7Z014S-2CLG484I can consolidate factory-gateway functions into a Zynq-7000 SoC, using the Cortex-A9 for Ethernet, protocol, security, and management tasks and programmable logic for deterministic packet handling or custom interfaces. Its 484-CSPBGA package provides 200 I/O for multiple field-bus levels and digital control signals. The 766 MHz operating point provides additional processing headroom, while the 65K logic cells can implement custom hardware offload. Deployment still requires careful isolation, surge protection, EMC design, and thermal analysis for factory environments.
Recommandé
Vision and Sensor Preprocessing
The XC7Z014S-2CLG484I fits vision-edge and sensor-processing systems that require software control alongside parallel hardware pipelines. The Artix-7 logic fabric can implement pixel capture formatting, thresholding, feature extraction, or sensor timing, while the Cortex-A9 manages configuration and higher-level analysis. With 200 I/O, the device can connect image sensors, memory, and control peripherals without a separate FPGA. Designers should constrain all video interfaces according to timing requirements and validate power, DDR, and thermal margins across the intended sensor workload.
Recommandé
Communications Gateway
The XC7Z014S-2CLG484I is suitable for protocol-conversion and communications gateways because the ARM processor can manage protocol stacks and the programmable logic can perform low-latency framing, filtering, or interface conversion. The 766 MHz Cortex-A9 and 200 I/O provide a balance of software flexibility and parallel connectivity. A practical design can place custom Ethernet or serial logic close to the physical interface and use the processor for configuration, logging, and secure management. Timing closure and signal-integrity validation are essential for high-speed links.
Recommandé
Networked Sensor Controller
The XC7Z014S-2CLG484I can act as a networked controller for connected sensors because the Cortex-A9 handles local software and communications while programmable logic manages deterministic sampling and local filtering. The 65K-cell fabric allows multiple sensor channels to be acquired and conditioned before data reaches the processor, reducing CPU workload and latency. Its 200 I/O and 484-CSPBGA package support dense integration, but thermal dissipation and decoupling become increasingly important as logic utilization and I/O switching rise.
Recommandé
Programmable Test and Measurement
The XC7Z014S-2CLG484I fits programmable instrumentation that combines real-time acquisition, control, and analysis in one device. Programmable logic can implement deterministic timing, pattern generation, filtering, or protocol decoding, while the 766 MHz Cortex-A9 handles configuration, calculations, and user interfaces. The 200 I/O permit broad connection to converters, memory, and trigger circuitry. For laboratory equipment, engineers should evaluate analog-noise coupling, DDR bit errors, clock jitter, and power-supply sequencing rather than relying only on nominal FPGA and processor performance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour XC7Z014S-2CLG484I — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | XC7Z014S-2CLG484C | XC7Z014S-1CLG484I | XC7Z014S-1CLG484C | XC7Z014S-1CLG484E | XC7Z014S-2CLG484E |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | 484-CSPBGA (19 mm x 19 mm) | 484-CSPBGA (19 mm x 19 mm) | 484-CSPBGA (19 mm x 19 mm) | 484-CSPBGA (19 mm x 19 mm) | 484-CSPBGA (19 mm x 19 mm) | 484-CSPBGA (19 mm x 19 mm) |
| Device Type | Zynq-7000 SoC | Zynq-7000 SoC | Zynq-7000 SoC | Zynq-7000 SoC | Zynq-7000 SoC | Zynq-7000 SoC |
| Processor | Single ARM Cortex-A9 MPCore with CoreSight | Single ARM Cortex-A9 MPCore with CoreSight | Single ARM Cortex-A9 MPCore with CoreSight | Single ARM Cortex-A9 MPCore with CoreSight | Single ARM Cortex-A9 MPCore with CoreSight | Single ARM Cortex-A9 MPCore with CoreSight |
| Processor Frequency | 766 MHz | 766 MHz | 667 MHz | 667 MHz | 667 MHz | 766 MHz |
| Logic Cells | 65K cells | 65K cells | 65K cells | 65K cells | 65K cells | 65K cells |
| Programmable Logic | Artix-7 FPGA | Artix-7 FPGA | Artix-7 FPGA | Artix-7 FPGA | Artix-7 FPGA | Artix-7 FPGA |
| I/O Count | 200 I/O | 200 I/O | 200 I/O | 200 I/O | 200 I/O | 200 I/O |
| Process Technology | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm |
| Temperature Suffix | I | C | I | C | E | E |
Principaux différenciateurs
- Higher listed processor speed than the -1 CLG484 options (vs XC7Z014S-1CLG484I)
- Retains the industrial temperature-grade suffix (vs XC7Z014S-2CLG484C)
- Same CLG484 footprint preserves PCB reuse (vs XC7Z014S-1CLG484C)
Notes de conception
Treat the XC7Z014S-2CLG484I power system as a multi-rail design rather than a single-supply device. Follow the AMD data sheet for processor, I/O, and auxiliary supply limits, startup timing, and decoupling. Place the required bypass capacitors directly beside their associated BGA power balls, use short and wide supply paths, and sequence rails in the prescribed order. Separately verify processor, programmable-logic, and DDR current because activity-dependent demand can materially change the board power budget.
Use AMD's CLG484 package pinout files and the selected PCB library to verify every BGA connection before routing. DDR and other high-speed interfaces should follow the recommended topology, with controlled impedance, continuous reference planes, and via symmetry intended to minimize skew. Avoid placing sensitive clock or differential pairs beside noisy power-regulator switching nodes. After layout, run Vivado DRC and timing analysis and compare implemented timing against the selected XC7Z014S speed grade.
Estimated thermal demand depends on processor activity, programmable-logic utilization, I/O switching, and ambient temperature, so calculate it with the power figures and thermal model in the AMD data sheet rather than a single nominal value. Provide uninterrupted ground and power planes beneath the BGA, add thermal-via arrays where the package design allows, and use a PCB copper area or heat-spreader arrangement appropriate to enclosure airflow. Validate the assembled board across maximum processor and logic activity at the highest intended ambient temperature.
Informations de conformité
RoHS compliance is stated by the exact-MPN product listing. No explicit REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 qualification statement was found for this part.