מוצרים (44,000+)

NAU7801KGI - 24-Bit Bridge Sensor ADC, I2C | Nuvoton
NAU7801KGI

NAU7801KGI - 24-Bit Bridge Sensor ADC, I2C | Nuvoton

The Nuvoton NAU7801KGI is a 24-bit delta-sigma analog-to-digital converter (ADC) designed as a complete analog front-end (AFE) for bridge sensors, offered in a DIP package with an I2C serial interface. According to Nuvoton product documentation for the NAU780 family, the device delivers up to 23-bit ENOB (effective number of bits) performance, making it capable of resolving microvolt-level signal changes from load cells and strain gauges. A bridge-sensor ADC is a precision data converter that amplifies, filters, and digitizes the tiny differential output of a Wheatstone bridge. In the signal-chain hierarchy, it sits between the analog sensor and the digital controller: sensor -> programmable gain amplifier (PGA) -> delta-sigma modulator -> digital filter -> I2C bus -> microcontroller. Integrating the entire front end in one IC eliminates discrete amplifier and filter design errors. Key features include 24-bit resolution with up to 23-bit ENOB, an integrated low-noise PGA for small differential inputs, on-chip digital filtering that suppresses line noise, dual-channel multiplexed inputs in the NAU780 family architecture, and a standard I2C interface for easy microcontroller integration. Low power consumption makes the part suitable for battery-operated weighing and sensing products. Architecturally, the delta-sigma modulator oversamples the amplified bridge signal, and the on-chip digital sinc filter decimates the stream to a high-resolution word, achieving the noise floor needed for weigh-scale and strain-gauge accuracy. The NAU7802 sibling in the same family is documented by Nuvoton as a complete front-end solution for bridge/sensor measurement with up to 23-bit ENOB. Typical applications include electronic weigh scales, strain-gauge measurement, pressure-sensor interfaces, and battery-powered precision sensing nodes where microvolt-level sensitivity is required. The DIP package simplifies prototyping and through-hole assembly. Design consideration: keep the analog front-end layout clean - use a stable low-noise reference, Kelvin-connect the bridge excitation and sense lines, and allow the digital filter to settle after gain or channel changes before reading data. This page synthesizes distributor data, family cross-references, and application guidance beyond the raw datasheet listing.

RFQ צור קשר
NAU85L40YG - Quad 24-bit Audio ADC with FLL | Nuvoton
NAU85L40YG

NAU85L40YG - Quad 24-bit Audio ADC with FLL | Nuvoton

The Nuvoton NAU85L40YG is a low-power, high-quality quad-channel audio ADC (analog-to-digital converter) for microphone array applications, delivering 24-bit resolution at up to 48 ksample/s, with integrated I2C control and I2S audio interfaces, housed in a 28-pin QFN (4x4 mm) package. An audio ADC is a special-purpose data converter that samples analog audio signals - typically from microphones - and converts them into digital data streams for DSP processing or transmission over digital audio buses. In the system hierarchy, it sits between analog front-end circuitry (microphones, preamplifiers) and digital audio processors such as voice engines, echo cancellers, and speech-recognition pipelines. Quad-channel audio ADCs like this one are purpose-built for microphone arrays used in far-field voice capture. Key features include four low-noise, high common-mode-rejection differential microphone inputs (MIC1 to MIC4), each followed by a programmable gain amplifier offering -1 dB to +36 dB gain with a fixed 12 kOhm input impedance. The integrated fractional-N FLL (frequency-locked loop) generates accurate audio sample-rate clocks from any system clock between 8 MHz and 33 MHz, eliminating the need for a dedicated audio crystal. Audio data can be routed to two I2S output ports for flexible multi-channel system integration. Architecturally, each channel combines the differential input stage, PGA, and a sigma-delta modulator followed by digital decimation filtering to achieve 24-bit output at 48 kHz. The preamplifier integration significantly reduces external component count, board area, and BOM cost in microphone-array designs. Typical applications include smart speakers and far-field voice assistants, conferencing and beamforming microphone arrays, and automotive or industrial voice-command front ends. The low-power profile suits always-listening, battery-conscious products. Design consideration: use the I2C interface to configure PGA gain per channel and verify FLL lock with the chosen system clock before bringing up the I2S links. This page synthesizes verified distributor data, drop-in alternatives, and design guidance not found in the manufacturer datasheet.

RFQ צור קשר
NB3N502DR2G - 14-190 MHz PLL Clock Multiplier, SOIC-8 | onsemi
NB3N502DR2G

NB3N502DR2G - 14-190 MHz PLL Clock Multiplier, SOIC-8 | onsemi

The onsemi NB3N502DR2G is a 14 MHz to 190 MHz Phase-Locked-Loop (PLL) clock multiplier IC housed in an 8-pin SOIC (3.90 mm narrow body) package that accepts a 2 MHz to 50 MHz fundamental-mode crystal or external reference clock and generates a low-jitter TTL/CMOS-level output clock at a precise multiple of the input reference. The device operates from a single 3.3 V or 5.0 V supply and delivers a 50 percent duty cycle output up to 190 MHz, making it a cost-effective replacement for discrete crystal oscillators in digital systems that need a multiplied reference clock. According to the onsemi datasheet, the input clock frequency range is 2 MHz to 50 MHz and the output frequency range is 14 MHz to 190 MHz with sub-nanosecond period jitter, providing clean timing for high-speed digital logic. A PLL clock multiplier is a feedback-controlled oscillator that phase-locks a Voltage-Controlled Oscillator (VCO) to a lower-frequency reference, allowing the system to derive a high-frequency clock from a low-frequency, low-cost crystal. In the broader taxonomy, the NB3N502 belongs to the clock-generator / frequency-synthesizer family of timing ICs, sitting beneath clock buffers and above generic phase-locked loops in the timing-and-signal-conditioning hierarchy of power management and signal-chain semiconductors. PLL multipliers are commonly used when a stable, low-jitter high-frequency clock is required but only a low-frequency crystal is available, or when the reference frequency must be precisely scaled to meet downstream logic requirements. Key features include TTL/CMOS-compatible output drive, internal loop filter components, and a wide industrial operating temperature range of -40 degrees C to +85 degrees C. The device integrates the PLL, VCO, and output divider on a single monolithic CMOS die, eliminating external loop-filter design. Its pin-selectable multiplier ratios (when applicable) and standard SOIC-8 footprint simplify drop-in replacement of legacy clock-generator circuits. The NB3N502DR2G is also Pb-free and supplied on a 2500-piece reel, suitable for high-volume surface-mount assembly. The architecture uses a digital phase-frequency detector driving an on-chip charge pump and VCO, with the multiplied output divided back to the reference frequency to close the loop. This analog PLL approach yields much lower jitter than simple frequency doublers built from XOR gates or delay lines, which is critical for downstream microcontrollers, FPGAs, and communications ASICs that derive internal clocks from the multiplied reference. The single-supply 3.3 V/5 V operation also simplifies integration into mixed-voltage designs without level shifters on the supply rail. Typical applications include replacing crystal oscillators in networking equipment, generating CPU/FPGA reference clocks in embedded systems, producing pixel clocks for video and display controllers, and providing low-jitter timing in industrial automation and instrumentation. The NB3N502DR2G is also widely used as a low-cost clock source for microcontroller (MCU) families that require an external multiplied reference. When designing with the NB3N502DR2G, ensure the input reference drive level meets the datasheet-specified VIH/VIL thresholds and that the PCB layout keeps the input trace short to minimize reflections. Decouple VDD3VCC with a 0.1 ohm ceramic + 10uF bulk capacitor pair, and place the load capacitor (when applicable) close to the IC to control output rise and fall characteristics.

RFQ צור קשר
NB3V1104CMTTBG - 1:4 LVCMOS Fanout Buffer 250MHz | onsemi
NB3V1104CMTTBG

NB3V1104CMTTBG - 1:4 LVCMOS Fanout Buffer 250MHz | onsemi

The onsemi NB3V1104CMTTBG is a 1:4 LVCMOS clock fanout buffer rated for operation up to 250 MHz, supplied in an 8-pin WDFN (2x2 mm) package. It accepts 3.3 V, 2.5 V, or 1.8 V LVCMOS input levels and produces four low-skew LVCMOS outputs. The device is part of the modular NB3V110xC family of low-skew, general-purpose LVCMOS clock buffers from onsemi. A clock buffer (or clock fanout buffer) is a timing component that receives a single reference clock on its input and reproduces multiple copies of that clock on its outputs. Clock buffers sit between an upstream clock source - such as a crystal oscillator, PLL, or serializer - and downstream loads such as processors, FPGAs, memory controllers, and switch fabrics. Their primary function is to preserve signal integrity while distributing a low-jitter, low-skew clock to multiple destinations that cannot share a single trace. Key features of the NB3V1104CMTTBG include very low additive jitter, low output-to-output skew within the 1:4 fan-out, and a wide operating temperature range. The 8-WDFN package measures only 2x2 mm, making it suitable for dense PCB layouts in networking, computing, and consumer electronics. Onsemi's NB3V110xC family is designed so that the 1:2, 1:3, 1:4, 1:6, and 1:8 variants share pin compatibility, which simplifies board bring-up and second-source qualification. Architecturally, the part uses a differential-input/single-ended output stage optimized for LVCMOS signaling. The input is designed to be driven by a 3.3 V, 2.5 V, or 1.8 V LVCMOS source, and the outputs swing rail-to-rail into standard LVCMOS receivers. Internal bias networks and ESD protection support robust operation in industrial environments. Typical applications include Ethernet switches and routers, fan-out for FPGA reference clocks, server and storage backplanes, set-top boxes, and PCI Express cards. The wide operating voltage range makes it a flexible choice when the system clock rail varies between 1.8 V and 3.3 V across board revisions. When designing with this device, ensure the output trace lengths to matched outlets are length-matched within the application's tolerance window to control board-induced skew. Place a 0.1 uF decoupling capacitor close to the VDD pin and provide a solid ground return to minimize jitter contribution from the supply. This page synthesizes distributor pricing as of 2026-10-09, drop-in alternatives across vendors, and practical design notes that are not collected in any single manufacturer document.

RFQ צור קשר
NB4N527S - 2.5Gb/s Dual AnyLevel to LVDS Translator | onsemi
NB4N527S

NB4N527S - 2.5Gb/s Dual AnyLevel to LVDS Translator | onsemi

The onsemi NB4N527S is a 3.3V, 2.5Gb/s dual AnyLevel to LVDS receiver/driver/buffer/translator with a wide input common-mode range of GND + 50 mV to VCC - 50 mV, two integrated 50 ohm internal termination resistors, and typical 350 mV LVDS output levels, housed in a 3 mm x 3 mm QFN-16 package. A level translator is an interface IC that converts signals from one logic standard or voltage domain to another while preserving signal integrity at high speed. In the signal-chain hierarchy, the NB4N527S sits between high-speed data or clock sources and LVDS receiver inputs, functioning simultaneously as a receiver, driver, buffer, and translator within the broader clock-and-data-distribution family of timing ICs. Key features include a maximum input clock frequency of up to 1.25 GHz, a 2.5Gb/s maximum data rate, and a common-mode range that accepts differential or single-ended inputs without external components. The two internal 50 ohm terminations eliminate the need for external resistor networks, reducing board area and component count while improving impedance matching consistency. Architecturally, the AnyLevel input stage compares incoming signals against the full supply-rail common-mode window, then regenerates them as clean LVDS differential outputs. This regeneration action reduces jitter accumulated upstream, which is why onsemi targets the device at jitter-sensitive, size-constrained designs. The small QFN-16 footprint suits dense line cards and modules where every square millimeter counts. Typical applications include data-center and telecom line-card clock distribution, wireless infrastructure radio chains, and high-speed logic-level interface translation between CML, PECL-style, or single-ended sources and LVDS backplanes. Design-wise, keep the 50 ohm internal terminations in mind: external terminations must not be added on terminated inputs, and input routing should be impedance-controlled. Short, matched differential output traces preserve the low-jitter benefit. This page synthesizes distributor listings, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
NBXDBB017LNHTAG - 156.25/312.5 MHz LVPECL XO Oscillator | onsemi
NBXDBB017LNHTAG

NBXDBB017LNHTAG - 156.25/312.5 MHz LVPECL XO Oscillator | onsemi

The onsemi NBXDBB017LNHTAG is a 3.3 V dual-frequency LVPECL crystal oscillator (XO) housed in a 6-pin CLCC (7x5 mm) surface-mount package. It provides selectable output frequencies of 156.25 MHz and 312.5 MHz using a high-Q fundamental crystal combined with an integrated PLL multiplier, delivering ultra-low jitter and phase-noise performance required for high-speed serial links. A crystal oscillator (XO) is a self-contained timing device in which a quartz resonator and an active oscillation/buffering circuit are co-packaged; unlike a bare crystal, an XO outputs a clean, conditioned logic-level clock and does not require external load capacitors. Within the broader clock-tree hierarchy, XOs sit above crystal units and below clock generators/buffers (and fanout buffers like LVPECL drivers), serving as the primary frequency reference for Serializer/Deserializer (SerDes) PHYs, FPGAs, network processors, and ASICs in telecom, datacom, and embedded systems. Key features of the NBXDBB017LNHTAG include a 3.3 V single supply, LVPECL differential outputs, frequency select via a control pin, typical RMS jitter on the order of single-digit picoseconds over 12 kHz to 20 MHz, and an industrial operating temperature range suitable for outdoor and uncontrolled thermal environments. The 6-CLCC package offers a small footprint with a hermetic ceramic body, which improves reliability under thermal cycling and mechanical stress compared with plastic molded oscillators. Technically, the device pairs a fundamental-mode crystal with a PLL multiplier block that synthesizes the second harmonic (312.5 MHz) from the 156.25 MHz fundamental; the output stage is an LVPECL driver that produces complementary ECL-style swings around a VCC-1.3 V common-mode voltage. LVPECL is preferred at these data rates because it provides low common-mode noise, high edge rates, and good immunity to supply noise relative to LVCMOS at multi-hundred-MHz frequencies. Typical applications include 1G/10G Ethernet PHY reference clocks, Fibre Channel and SONET/SDH line cards, PCIe and RapidIO reference inputs, FPGA logic-clock inputs, and clock trees for switches and routers. The selectable dual frequency lets one BOM line serve boards that need both the base rate and the doubled rate. When designing with this part, place it adjacent to the receiver IC, keep LVPECL traces length-matched within a few mils, terminate each side with the standard 50 ohm to VTT network, and provide solid 0.1 uF plus bulk-decoupling on the supply pin. The frequency-select pin should be tied directly to logic, not floated, to avoid undefined output behavior. This page synthesizes distributor pricing, drop-in compatible onsemi alternates, and practical PCB-layout guidance that the bare manufacturer datasheet does not consolidate in one place.

RFQ צור קשר
NC7S00M5X - TinyLogic HS 2-Input NAND Gate, SOT-23-5 | onsemi
NC7S00M5X

NC7S00M5X - TinyLogic HS 2-Input NAND Gate, SOT-23-5 | onsemi

The onsemi NC7S00M5X is a single 2-input high-performance CMOS NAND gate fabricated using advanced silicon-gate CMOS technology, housed in a 5-pin SOT-23-5 surface-mount package. It is part of the TinyLogic HS (High-Speed) family and operates over a wide VCC range of 2.0 V to 6.0 V with a typical propagation delay of approximately 3 ns at 5 V supply, delivering low-power CMOS performance with TTL-compatible switching thresholds. A NAND gate is a fundamental digital logic primitive that performs the logical NAND (NOT-AND) operation on its two inputs. The output is logic LOW only when both inputs are HIGH; otherwise, the output is logic HIGH. As a member of the logic gate family, NAND gates sit inside the Boolean logic hierarchy (AND/OR/NOT/NAND/NOR/XOR), and the NAND gate is functionally complete, meaning any other Boolean function can be implemented using only NAND gates. Within an integrated circuit's hierarchy, the NC7S00 belongs to the logic ICs category, specifically the sub-category of gates and inverters, which feed into larger functions such as flip-flops, arithmetic logic units, and microcontrollers. Key features of the NC7S00M5X include ultra-low quiescent current (ICC < 1 µA at VCC = 5.5 V), high noise immunity thanks to three internal gain stages between input and output, balanced output drive, and ESD protection diodes on all inputs/outputs referenced to the VCC and GND rails. The SOT-23-5 footprint makes it suitable for space-constrained designs such as hand-held, battery-powered, and portable consumer electronics. Architecturally, the NC7S00 uses an advanced silicon-gate CMOS process that combines low static power consumption with high switching speed. The output stage is balanced, capable of sourcing and sinking comparable currents, which improves AC performance in symmetrical loads and prevents ground-bounce issues in dense multi-gate boards. Inputs tolerate voltages up to VCC plus 0.5 V without damage. Typical applications include handheld and portable electronics, general-purpose logic level translation and interface buffering, signal conditioning in sensor front-ends, low-power standby controllers, mobile phones, PDAs, and industrial control logic where minimal board area is critical. Designers often use the NC7S00M5X as a building block for oscillator circuits, reset sequencers, and conditional-enable logic. When designing with this device, observe proper high-frequency PCB practices: place a 0.1 µF decoupling capacitor within 2 mm of the VCC pin, and route input traces away from the output to avoid feedback-induced oscillations. The input ESD network makes the pin robust to handling, but layout cleanliness still determines overall system noise immunity. This page consolidates distributor pricing for the NC7S00M5X, identifies pin-compatible drop-in alternatives in the same SOT-23-5 footprint, and provides design notes that complement the manufacturer datasheet without repeating it verbatim.

RFQ צור קשר
NC7S02M5X - TinyLogic 2-Input NOR Gate SOT-23-5 | onsemi
NC7S02M5X

NC7S02M5X - TinyLogic 2-Input NOR Gate SOT-23-5 | onsemi

The onsemi NC7S02M5X is a single 2-input high-performance CMOS NOR gate from the TinyLogic HS (High Speed) family, supplied in a 5-pin SOT-23-5 surface-mount package on tape and reel. Fabricated in advanced silicon-gate CMOS, it delivers high-speed, low-power logic operation over a broad VCC range. A logic gate is the most fundamental building block of digital electronics: it takes binary inputs and produces a binary output according to Boolean rules. A NOR gate outputs a LOW only when any input is HIGH, and is functionally complete, meaning any digital circuit can be built from NOR gates alone. Single-gate logic devices like the NC7S02 occupy the lowest level of the logic IC hierarchy, below multi-gate families such as 74HC quad gates, and belong to the broader class of small-scale integration (SSI) CMOS logic. Key features of the NC7S02 include TinyLogic HS single-gate packaging that saves board space versus quad-gate SOIC-14 alternatives, silicon-gate CMOS technology for speed with minimal static power consumption, and ESD protection diodes on both inputs and output with respect to VCC and GND rails. Three stages of gain between inputs and outputs assure high noise immunity and reduced propagation-delay sensitivity. Technically, the three-stage output buffering provides symmetrical drive and sharp transitions, while the broad VCC range allows direct interfacing with 5V, 3.3V, and lower-voltage logic domains within the specified operating limits. The inherent rail-clamping ESD structure simplifies board-level protection in mixed-signal environments. Typical applications include glue logic in microcontroller and FPGA systems, power-down domain isolation in battery-powered portable equipment, signal inversion or OR-ing in space-constrained designs, and retry or reset control in embedded industrial boards such as MC9S08 or MC9S12 based systems. When designing with this part, keep unused input tied to a valid logic level (VCC or GND) to prevent oscillation, and place 0.1uF decoupling close to the VCC pin. Confirm propagation delay and drive current against the onsemi datasheet for your VCC and temperature corner. This page synthesizes distributor pricing tiers, drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
NC7S02M5X-L22090 - TinyLogic HS 2-Input NOR Gate | onsemi
NC7S02M5X-L22090

NC7S02M5X-L22090 - TinyLogic HS 2-Input NOR Gate | onsemi

The onsemi NC7S02M5X-L22090 is a single-channel 2-input NOR gate fabricated in advanced CMOS silicon-gate technology and housed in a 5-pin SOT-23-5 (TSOP-5/M5) surface-mount package. It belongs to the TinyLogic HS (High-Speed) family, offering high-speed logic operation over a broad VCC supply range in one of the smallest standard discrete-logic footprints available. A NOR gate is a fundamental combinational logic element that outputs a LOW only when all inputs are HIGH; it is functionally complete, meaning any digital circuit can be built from NOR gates alone. In the digital IC hierarchy, the NC7S02 sits within the single-gate logic IC category (also called little logic or TinyLogic), between full 74-series multi-gate packages and application-specific ICs, and is used wherever board space, propagation delay, or parasitic loading make a full quad-gate package impractical. Key features include single 2-input NOR functionality in SOT-23-5, CMOS construction for very low static power consumption, ESD protection diodes on both inputs and the output relative to VCC and GND, and three stages of internal gain that assure high noise immunity while reducing output-stage switching sensitivity, per the onsemi NC7S02 datasheet. Technically, the silicon-gate CMOS process delivers speed comparable to bipolar-era logic at CMOS power levels, and the buffered three-stage topology isolates the inputs from the output transition, minimizing ground bounce in mixed-signal boards. The broad VCC operating range allows direct interfacing with 3.3V and 5V logic domains within rated conditions. Typical applications include glue logic in microcontroller and FPGA systems, oscillator and RC-timer circuits, pulse stretching and delay generation, enable/signal gating in portable and battery-powered consumer devices, and board-level chip-select combining where a full 74x02 package would waste space. Design consideration: as with all single-gate CMOS parts, unused input states must never float - tie unused inputs to VCC or GND through an appropriate connection to prevent oscillation and excess current. Keep decoupling (100 nF) close to pin 5. This page synthesizes verified distributor pricing from DigiKey, Mouser, Octopart and Vyrian, same-package drop-in alternatives, and practical design notes that are not consolidated in the manufacturer datasheet.

RFQ צור קשר
NC7SV125P5X - TinyLogic ULP-A Non-Inverting 3-State Buffer, SC-70-5 | onsemi
NC7SV125P5X

NC7SV125P5X - TinyLogic ULP-A Non-Inverting 3-State Buffer, SC-70-5 | onsemi

The onsemi NC7SV125P5X is a single non-inverting 3-state buffer from the TinyLogic Ultra Low Power-A (ULP-A) family, housed in a 5-pin SC-70 surface-mount package. It is designed for VCC operation from 0.9 V to 3.6 V, and is fabricated in CMOS technology to deliver extreme high speed, high drive, and low static power consumption in tiny footprint packages. A 3-state buffer (also called a tri-state buffer, line driver, or bus driver) is a single-input/single-output non-inverting logic device whose output can be placed in one of three states: logic high, logic low, or high-impedance (Hi-Z). Buffers are the simplest members of the Logic ICs category, sitting hierarchically below gates, transceivers, and bus switches. Their primary function is signal isolation, level shifting, bus arbitration, and output drive-strength amplification on shared digital lines such as microcontroller I/O buses, memory data lines, and peripheral interconnects. Key specifications of the NC7SV125P5X include a wide VCC range of 0.9 V to 3.6 V, ±24 mA output drive at 3.3 V VCC, low quiescent current typically below 1 µA, and a propagation delay in the low-nanosecond range that supports high-speed digital interfaces. The 3-state output is controlled by an active-low output enable (OE\) pin; when OE\ is high the output enters Hi-Z, allowing multiple devices to share a common bus. The SC-70-5 package measures approximately 2.0 mm x 1.25 mm, making it one of the smallest logic footprints available. Architecturally the device uses a minimum-stage CMOS inverter chain, which is why propagation delay is extremely short and dynamic power scales linearly with load capacitance and switching frequency. The NC7SV125P5X is specified over the industrial -40 °C to +85 °C temperature range and is fully RoHS compliant, with Pb-free lead finish and a Moisture Sensitivity Level (MSL) of 1, simplifying handling and board assembly. Typical applications include mobile phones, tablets, wearable electronics, IoT sensor nodes, handheld instruments, and any battery-powered product that needs bus isolation or output drive amplification in a sub-3 mm² footprint. Designers favor this part when board real estate is at a premium and a low-power, rail-to-rail CMOS buffer is required. When designing with the NC7SV125P5X, place input and output decoupling capacitors (typically 0.1 µF) close to the VCC and GND pins to limit supply-rail bounce during high-speed switching. Always keep the OE\ pin at a defined logic level; floating enables can cause shoot-through current and unwanted output toggling. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers quickly decide whether the NC7SV125P5X is the right 3-state buffer for their next low-power, space-constrained design.

RFQ צור קשר
NC7SZ00M5X - UHS 2-Input NAND Gate, SOT-23-5 | onsemi
NC7SZ00M5X

NC7SZ00M5X - UHS 2-Input NAND Gate, SOT-23-5 | onsemi

The onsemi NC7SZ00M5X is a single two-input NAND gate from the TinyLogic Ultra-High Speed (UHS) series, fabricated with advanced CMOS technology to achieve 2.4 ns typical propagation delay while maintaining low static power dissipation across a 1.65 V to 5.5 V VCC operating range, housed in a 5-pin SOT-23 (SC-74A / SOT-753) package. A NAND gate is a fundamental digital logic primitive that performs the logical complement of the AND operation: the output is LOW only when both inputs are HIGH, otherwise the output is HIGH. NAND gates are functionally complete - any Boolean function can be implemented using only NAND gates - which is why they are the most replicated gates in CMOS digital IC families. Within the broader taxonomy, the NC7SZ00 belongs to the TinyLogic UHS family, which sits under standard logic gates, which sits under logic ICs, which sits under integrated circuits. Key features include 2.4 ns typical propagation delay (tPD) into a 50 pF load at 5 V VCC, ±24 mA high output drive at 3 V VCC, broad 1.65 V to 5.5 V operating range, and proprietary noise/EMI reduction circuitry. The device is over-voltage tolerant on inputs, facilitating 5 V to 3 V translation without external level shifters. The NC7SZ00 architecture uses a standard CMOS NAND topology with input hysteresis and balanced output drive, optimized for sub-3 ns switching at low power. Matched LCX-class performance at 3.3 V VCC means it can directly replace legacy LCX NANDs in mixed-voltage designs without PCB rework. Typical applications include portable and battery-powered devices, mobile phone handsets, computing peripherals, level shifting between 5 V and 3.3 V domains, and general-purpose glue logic on microprocessor and ASIC boards. The SOT-23-5 footprint makes it ideal for space-constrained handheld designs. When designing with this device, observe standard CMOS handling precautions: unused inputs must be tied to VCC or GND to prevent floating, and high-impedance I/O behavior occurs during power-down. Decouple VCC with a 0.1 µF ceramic capacitor placed close to the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in the onsemi datasheet, giving engineers a single reference for selection, sourcing, and PCB-level integration.

RFQ צור קשר
NC7SZ04P5X - Single UHS TinyLogic Inverter, 5.5V | onsemi
NC7SZ04P5X

NC7SZ04P5X - Single UHS TinyLogic Inverter, 5.5V | onsemi

The onsemi NC7SZ04P5X is a single-channel CMOS inverter from the TinyLogic Ultra-High Speed (UHS) series, housed in a 5-pin SC-70 package (P5X suffix). It operates over a 1.65 V to 5.5 V VCC range and delivers a typical propagation delay of 2.4 ns into a 50 pF load at 5 V VCC, while the ±24 mA output drive at 3 V VCC provides strong signal integrity. According to the onsemi datasheet for the NC7SZ04 family, the part is fabricated with advanced CMOS technology to achieve ultra-high speed with high output drive and low static power dissipation over the full 1.65 V to 5.5 V supply range. What is a TinyLogic UHS inverter? A TinyLogic UHS (Ultra-High Speed) inverter is a single-stage CMOS logic gate that performs the logical NOT function (Y = ~A) and belongs to the TinyLogic family of discrete logic ICs. In the broader component taxonomy, this device is a logic gate -> inverter -> digital logic IC -> semiconductor IC. These gates are ideal for level translation, signal inversion, clock buffering, and general-purpose logic glue in mixed-voltage systems where board space is critical and a single inverter is needed. Key features of the NC7SZ04P5X include ±24 mA high output drive at 3 V VCC, an over-voltage tolerant input that facilitates 5-V to 3-V translation, power-down high-impedance inputs/output, proprietary noise/EMI reduction circuitry, and propagation delay that matches LCX performance when operated at 3.3 V VCC. The device is also offered in an ultra-small MicroPak leadless package for space-constrained designs. Architecturally, the NC7SZ04P5X uses advanced CMOS with a standard CMOS input structure. The high output drive (±24 mA at 3 V VCC) means it can drive heavily loaded buses and long PCB traces while maintaining fast rise/fall times. The over-voltage tolerant input allows 5 V CMOS signals to be safely applied even when VCC is as low as 1.65 V, eliminating the need for external level shifters in many mixed-voltage designs. Typical applications include level translation between 5 V and 3.3 V logic domains, general-purpose logic inversion in handheld and portable devices, signal conditioning in battery-powered equipment, oscillator and clock-buffer building blocks, and fan-out for microcontroller GPIO in space-constrained designs. The SC-70-5 footprint makes it well suited when only a single inverter is required on a dense mixed-signal board. When designing with this device, route der through a 5-pin to keep the trace between the input pin and the source under 50 mm and place a 0.1 µF decoupling capacitor within 5 mm of the VCC pin to maintain power-rail noise immunity. The over-voltage tolerant input is a key design advantage in mixed-voltage systems where 5 V CMOS signals can be applied even when VCC is as low as 1.65 V, allowing true 5 V-to-3 V translation without external protection. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-brand onsemi family members and pin-compatible cross-brand equivalents for second-source flexibility.

RFQ צור קשר
NC7SZ08L6X - Ultra-High-Speed 2-Input AND Gate | onsemi
NC7SZ08L6X

NC7SZ08L6X - Ultra-High-Speed 2-Input AND Gate | onsemi

The onsemi NC7SZ08L6X is a single two-input AND gate in the TinyLogic Ultra-High Speed family, operating from 1.65 V to 5.5 V in a 6-pin MicroPak package. It combines fast propagation performance with high output drive and low static power dissipation across a broad supply range. The L6X ordering code identifies the onsemi surface-mount package and tape-and-reel shipping configuration. A logic AND gate is a combinational digital component that produces a high output only when every input is high. This gate belongs to the hierarchy of CMOS logic gates, digital logic ICs, semiconductors, and broader digital electronics. A single two-input gate is useful when a design requires basic Boolean AND behavior in compact routing, signal conditioning, control logic, or low-power digital interfaces. The NC7SZ08 is fabricated with advanced CMOS technology. Its specified 1.65 V to 5.5 V supply operation supports both low-voltage digital systems and conventional 3.3 V or 5 V rails. The TinyLogic UHS positioning emphasizes ultra-high-speed operation while retaining low static power dissipation. These characteristics make the device appropriate where logic transitions must be handled quickly without using a larger multi-gate package. The verified distributor listings identify the NC7SZ08L6X as an AND gate IC with one channel, two inputs, and a 6-MicroPak package. Available source material confirms the TinyLogic UHS 2-input AND function and CMOS technology. Exact propagation-delay, output-current, input-threshold, and temperature values were not supplied in the retrieved source data and therefore are not asserted here. Typical uses include low-voltage control logic, digital signal routing, status-flag generation, and compact embedded systems where a dedicated two-input AND function is preferable to implementing the Boolean operation in a larger programmable or multipurpose logic device. Designers should also consider whether the required logic family, supply voltage, input levels, and timing satisfy the system requirements. For PCB layout, keep the unused input connected to a defined logic level rather than leaving it floating, and place the device close to the signals it serves. Confirm the exposed-pad or thermal-pad requirements in the manufacturer package drawing and verify the pin mapping against the applicable datasheet before releasing a layout. This product page combines verified distributor identity, package information, pricing references, technical context, and replacement guidance. It distinguishes confirmed facts from parameters that still require direct confirmation from the manufacturer datasheet, helping engineers make sourcing and design decisions without relying on unsupported assumptions.

RFQ צור קשר
NC7SZ125M5X - UHS Single Buffer, 3-State, SOT-23-5 | onsemi
NC7SZ125M5X

NC7SZ125M5X - UHS Single Buffer, 3-State, SOT-23-5 | onsemi

The onsemi NC7SZ125M5X is a single non-inverting buffer with 3-STATE capability, fabricated with advanced CMOS technology to deliver ultra-high speed (UHS) switching with high output drive while maintaining low static power dissipation. Housed in a 5-pin SOT-23 (M5) surface-mount package, the device operates across a wide 1.65 V to 5.5 V VCC range, supports ±24 mA output drive at 5 V, and features a typical propagation delay of approximately 2.6 ns at 5 V VCC, making it well suited for high-speed signal conditioning in mixed-voltage systems. The 3-STATE output is controlled by an active-low output enable (OE) pin, allowing bus-oriented applications and easy interface to microcontrollers, ASICs, and FPGAs. A non-inverting buffer (also called a line driver or signal repeater) is a single-input, single-output logic function that reproduces the logic level present at its input at the output, providing current gain and isolation between a weak source and a heavier load. Within the broader logic IC hierarchy, this part belongs to the TinyLogic UHS family from onsemi, a subset of CMOS logic gates that trade absolute speed for low power consumption. The 3-STATE output allows multiple buffers to share a common bus, with the disabled buffer entering a high-impedance state to avoid contention. The SOT-23-5 package is one of the most ubiquitous footprints in modern surface-mount design. Key features of the NC7SZ125M5X include balanced propagation delays, very low quiescent current (typically 1 µA at room temperature), ±24 mA output drive at 5 V (enabling direct drive of LEDs or small relays), and a wide VCC operating range that makes it compatible with 1.8 V, 2.5 V, 3.3 V, and 5 V logic families. The device contains a single Schmitt-trigger input, providing hysteresis for slow or noisy input edges. Tape and reel packaging (suffix X) supports high-volume automated assembly. From a technical perspective, the NC7SZ125M5X uses a standard CMOS push-pull output stage. The output enable pin OE is internally pulled high through a weak pull-up, so the output remains in high-impedance until actively driven low. Input structures tolerate voltages up to 5.5 V regardless of VCC, allowing level translation between 1.8 V and 5 V domains. ESD protection exceeds 2000 V HBM per industry standards, and latch-up immunity is rated above 100 mA per JESD78. Typical applications include signal buffering between low-drive microcontroller GPIOs and heavier loads such as LEDs, level translation between mixed-voltage logic domains (e.g., 1.8 V to 3.3 V), bus isolation and multiplexing in distributed systems, and general-purpose logic inversion-free signal restoration in handheld and battery-powered designs. In industrial PLCs, it isolates backplane logic from field-side noise. In consumer audio and wearables, it buffers buttons or I2C lines between SoCs and accessory connectors. When designing with this part, ensure OE is driven to a defined logic level rather than left floating, especially in noisy environments, to avoid inadvertent bus contention. Place a 0.1 µF decoupling capacitor close to the VCC pin to suppress logic-stage switching transients, and avoid exceeding the absolute maximum VCC of 6 V. This TinyLogic buffer excels where a single-bit driver, three-state capability, and tiny footprint are required simultaneously. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, comparison parameters, and practical design notes that go beyond what is printed in the manufacturer datasheet alone, giving engineers a faster path from selection to validated PCB layout.

RFQ צור קשר
NC7SZ125M5X-L22090 - TinyLogic UHS Buffer 3-State SOT-23-5 | onsemi
NC7SZ125M5X-L22090

NC7SZ125M5X-L22090 - TinyLogic UHS Buffer 3-State SOT-23-5 | onsemi

The onsemi NC7SZ125M5X-L22090 is a TinyLogic Ultra-High Speed (UHS) single non-inverting buffer with a three-state output, fabricated in advanced CMOS to deliver high output drive and ultra-high switching speed while keeping static power dissipation minimal. Packaged in a 5-pin SOT-23 (M5), the device operates over a 1.65 V to 5.5 V VCC range, supports ±24 mA output drive at 4.5 V, and is rated for industrial -40 C to +85 C operation per the onsemi NC7SZ125 datasheet family. The active-low /OE enable pin allows bus-style multiplexing and high-impedance output when de-asserted. A buffer in CMOS logic is a non-inverting driver that copies a digital input to its output while providing isolation and current amplification between source and load. Buffers belong to the broader family of logic ICs under digital signal conditioning, alongside inverters, transceivers, and line drivers; TinyLogic UHS parts sit at the high-speed end of this taxonomy, optimized for short propagation delay and high fan-out within a small SOT-23 outline. Key specifications include a propagation delay (tPD) of approximately 2.6 ns at 5 V, output drive of ±24 mA at 4.5 V VCC, quiescent current well under 10 uA across the supply range, and TTL-compatible inputs when VCC is at 4.5 V to 5.5 V. The /OE pin features an internal pull-up so the output defaults to high-impedance (effectively disabled) if the pin is left floating, simplifying power-up behavior in mixed-voltage buses. The NC7SZ125 architecture uses a single-stage CMOS inverter/buffer chain with a tri-state output totem pole. Because the silicon is specified over 1.65 V to 5.5 V, the same footprint can serve 1.8 V, 2.5 V, 3.3 V, and 5 V logic domains, making it ideal as a voltage-level translation element when driven from a lower-voltage controller I/O into a higher-voltage bus. Typical applications include point-to-point signal buffering in portable and consumer devices, I/O expansion for microcontrollers, address/data bus isolation in memory and display interfaces, and translation between logic domains in mixed-voltage systems. It is also commonly used as a high-impedance power-gating switch for sub-system rails. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to the VCC pin, and treat the SOT-23-5 thermal pad (when present) as a low-impedance ground return. Avoid driving large capacitive loads (>50 pF) without series damping, because the high drive strength can create ground-bounce issues on tightly-routed boards. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the onsemi datasheet alone, giving engineers a faster decision path for cross-brand or second-source selection.

RFQ צור קשר
NC7WZ14EP6X - UHS Dual Inverter Schmitt Trigger SC-70-6
NC7WZ14EP6X

NC7WZ14EP6X - UHS Dual Inverter Schmitt Trigger SC-70-6

The onsemi NC7WZ14EP6X is a dual Schmitt-trigger inverter from the TinyLogic Ultra-High Speed (UHS) Series, packaged in a 6-pin SC-88 (SC-70-6) surface-mount outline. It operates from 1.65 V to 5.5 V VCC, delivers ±24 mA of balanced output drive at 4.5 V, and achieves typical propagation delays of about 2.0 ns at 5 V. The on-suit Schmitt trigger hysteresis on each input cleans up slow or noisy edges, making the part well suited for signal conditioning in mixed-voltage digital designs. A Schmitt-trigger inverter is a single-input logic gate that outputs the logical complement of its input while adding positive feedback to define two distinct switching points (VT+ and VT-). The hysteresis voltage (typically ~1 V at 5 V) rejects noise on slowly rising or ringing edges that would otherwise chatter a standard CMOS inverter. In the broader TinyLogic family tree it sits beside standard inverters (NC7WZ04) and buffers (NC7WZ17) as the noise-immune variant. Key features of the NC7WZ14EP6X include 1.65 V to 5.5 V VCC operation, ±24 mA output drive at 4.5 V, balanced 4 mA sink/source at 3 V, a propagation delay near 2 ns at 5 V, Schmitt trigger inputs on both channels, and a quiescent current below 1 uA. The SC-88 package with a -40 C to +85 C operating range suits portable and industrial designs where board area is critical. Internally, NC7WZ14EP6X uses advanced sub-micron CMOS to combine very high speed with low static power dissipation across the full VCC range. Two independent inverters share only GND and VCC, simplifying layout. The balanced ±24 mA drive at 4.5 V lets outputs drive long PCB traces or several CMOS loads while keeping edges fast. Typical applications include logic-level translation, oscillator and relaxation-circuit building blocks, debouncing mechanical switches, waveform shaping for sensor outputs, and general-purpose inversion in portable consumer, computing and IoT hardware. It is widely used as a companion to microcontrollers where a clean digital signal is needed. When laying out the SC-88 footprint, place a 0.1 uF VCC decoupling capacitor within about 3 mm of pin 6, keep input traces short to preserve hysteresis noise rejection, and avoid running outputs near analog sections. The -EP6X suffix marks a 3000-piece tape-and-reel packing, -P6X denotes SC-88 (tape and reel), and -P6 marks the same SC-88 on tape. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical layout notes that are not bundled together in the manufacturer datasheet.

RFQ צור קשר
NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi
NCS199A1RSQT2G

NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi

The onsemi NCS199A1RSQT2G is a zero-drift, voltage-output current-shunt monitor (current sense amplifier) with a fixed gain of 50 V/V, supplied in a 6-pin SC-88 / SC-70-6 / SOT-363 surface-mount package. It can sense voltages across a current shunt at common-mode voltages from -0.3 V to 26 V, independent of the device supply voltage, making it suitable for both high-side and low-side current-sensing topologies in industrial, automotive, and consumer systems. The device operates from a single supply of 2.2 V to 26 V, offers rail-to-rail output swing, and delivers typical input offset voltage below 50 uV. A current sense amplifier (CSA) is a type of instrumentation amplifier that converts a small differential voltage developed across a shunt resistor into a ground-referenced output voltage proportional to load current. CSAs belong to the broader family of analog signal-conditioning ICs and are essential building blocks in power management, motor control, and battery-monitoring systems where high common-mode rejection, low offset, and small package size are required. Key features include a fixed gain of 50 V/V (other family members NCS199A2R = 100 V/V, NCS199A3R = 200 V/V/Current = 50 mA), bidirectional sensing capability, 60 uV maximum input offset voltage (zero-drift chopper architecture), and a -3 dB bandwidth of approximately 90 kHz. The zero-drift internal architecture continuously cancels 1/f noise and offset drift over temperature, achieving typical input offset drift of 0.5 uV/C. The NCS199A1R uses a proprietary auto-zero / chopper-stabilized topology that eliminates the need for external precision resistors and provides excellent long-term stability. Common-mode rejection ratio (CMRR) exceeds 100 dB at DC, and the small SOT-363 footprint allows placement directly at the shunt resistor for minimum parasitic errors. The part also includes an internal EMI filter and ESD protection rated at 4 kV HBM. Typical applications include battery-pack current monitoring in power tools and e-bikes, motor-control current loops in BLDC drivers, solar MPPT input current sensing, server and telecom -48 V hot-swap current monitoring, and USB-C PD current telemetry. In all cases the wide -0.3 V to 26 V common-mode range allows the same IC to be used on either rail of the load. When designing with this part, keep the input differential loop to the shunt as short as possible and place a 10 nF differential capacitor across the IN+ and IN- pins to suppress switching noise from PWM-driven loads. Ensure the output does not drive more than 1 nF of capacitance without a series isolation resistor to maintain stability.

RFQ צור קשר
NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi
NCV2202SN2T1G

NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi

The onsemi NCV2202SN2T1G is a sub-one-volt, low-power, single-channel CMOS comparator in a 5-pin SOT-23 (TSOP) package, qualified to the AEC-Q100 automotive standard. It operates over a supply voltage range of 0.85V to 6.0V, consumes only 10 uA of quiescent current, and provides an open-drain output capable of rail-to-rail input and rail-to-rail output swing. The NCV2202 prefix indicates AEC-Q100 / PPAP-capable automotive grade screening, while the non-automotive NCS2202 family member shares the same die and pinout. What is a low-voltage CMOS comparator? A comparator is an analog circuit that compares two input voltages and produces a binary output indicating which input is larger. Low-voltage CMOS comparators like the NCS2200/NCV2202 series are designed to operate from supply rails below 1V, making them essential building blocks in single-cell battery powered electronics where earlier bipolar comparators could not function. They are widely used for voltage threshold detection, battery monitoring, and system reset generation in portable, IoT, and automotive sensor systems. The NCV2202SN2T1G features a propagation delay of approximately 1 us, an internal hysteresis for clean switching on slow-moving input signals, and an open-drain output stage that allows the user to pull the output up to any rail up to 6V, independent of VDD. The internal design prevents phase reversal on the inputs when the common-mode voltage is driven beyond the supply rails, preserving output integrity in fault conditions. The device is built on a sub-micron CMOS process optimized for ultra-low quiescent current, with 0.3 uA consumption when the enable pin is held low (output tri-state). Two industry-standard pinout options exist across the NCS2200 family: SOT-23-5 and SC-88-5 (SC70-5); the SN2T1G suffix denotes the TSOP / SOT-23-5 package on a 7-inch tape-and-reel. Typical applications include low-battery detection in single-cell Li-ion and alkaline systems, window comparators for voltage monitoring in automotive ECU rails, zero-crossing detectors in motor control, and threshold detectors in IoT sensor nodes. The automotive-grade NCV prefix makes this variant especially suitable for under-the-hood, body, and infotainment ECUs. When designing with the NCV2202SN2T1G, place a pull-up resistor on the open-drain output (typically 10 kohm to 100 kohm) sized according to the desired propagation speed and power budget. Decouple VDD with a 100 nF ceramic capacitor located within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

RFQ צור קשר
NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi
NCV2250SN2T3G

NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi

The onsemi NCV2250SN2T3G is a single high-speed, low-voltage, rail-to-rail comparator with push-pull output, packaged in a 5-pin TSOP. It delivers a typical propagation delay of 50 ns with a 100 mV input overdrive, making it well suited for fast threshold detection in space-constrained designs. The part operates from a single 1.8 V to 5.5 V range, and the input common-mode range extends 200 mV beyond both supply rails, allowing direct sensing near ground or VCC. The push-pull output stage eliminates the external pull-up resistor required by open-drain alternatives and swings to within millivolts of both rails. A comparator is an analog active device that compares two input voltages and drives its output logic a discrete single (high or low) based on which input is more positive. Within the broader taxonomy, the NCV801A sits under analog comparator -> comparator -> amplifier/comparator IC -> semiconductor. Push-pull CMOS output topology differs from open-drain comparators (such as the classic LM393) by actively driving both high and low states, enabling faster edges and lower power in many applications. This category of comparator is essential in any mixed-signal system requiring fast logic-level translation from analog signals. Key features include 1.8 V to 5.5 V single-supply operation, 200 mV beyond-the-rails input common-mode range, 50 ns typical propagation delay (100 mV overdrive), push-pull CMOS output, low quiescent current, and automotive-grade NCV prefix indicating PPAP-capable qualification per onsemi's automotive quality program. The 5-TSOP package consumes only a few square millimeters of PCB area, ideal for compact sensor and signal-conditioning modules. The NCV2250 is built on a standard CMOS process with on-chip ESD protection diodes on the inputs and outputs. The rail-to-rail input stage uses a complementary differential pair topology that maintains linear behavior across the full common-mode range. Internally, hysteresis can be introduced via external positive feedback resistors to prevent output chattering on slow-moving inputs. The NCV2250SN2T3G is functionally identical to the NCS2250SN2T3G except for automotive-grade qualification and traceability. Typical applications include zero-crossing detectors for line-voltage sensing, battery voltage monitoring in 12 V automotive systems, window comparators with multi-threshold detection, motor control feedback loops, sensor signal conditioning for microcontroller ADC front-ends, and threshold alarms in industrial control. The wide input common-mode range is particularly valuable for current-sense applications where the sense resistor sits at a high common-mode voltage close to the supply rail. When designing with this part, ensure input signals stay within the ESD rating of the device and consider adding small input series resistance to limit fault current during over-voltage transients. Decoupling the supply pin with a 100 nF ceramic capacitor placed within 3 mm of the VCC pin is essential for stable high-frequency switching performance. This page synthesizes distributor inventory, the parametric equivalent on the manufacturer's cross-reference database, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi
NCV2904DR2G

NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi

The onsemi NCV2904DR2G is a single-supply dual operational amplifier in an 8-pin SOIC (Case 751) package, operating from 3.0 V to 26 V with a common-mode input range extending to ground/VEE, targeted at automotive-grade applications. An operational amplifier (op-amp) is a high-gain differential voltage amplifier that sits within the analog signal chain hierarchy: op-amp -> amplifier IC -> analog IC -> semiconductor. Dual op-amps integrate two independent amplifier cores in one package, halving board space and BOM line items versus two singles. Single-supply op-amps like the NCV2904 are specifically designed for input common-mode ranges that reach the negative rail, making them usable directly on ground-referenced sensor signals without negative supplies. Key features of the NCV2904 include low power drain, short-circuit protected outputs, a true differential input stage, internally compensated frequency response, and ESD clamps on the inputs. The NCV prefix designates onsemi automotive qualification and temperature screening, making this device suitable for under-hood and body-electronics environments. Per the onsemi datasheet, the LM358 series is equivalent to one-half of an LM324, positioning the NCV2904 as the automotive member of this industry-standard family. Technically, the NCV2904 uses the circuit designs perfected for the quad LM2904/LM324 family: an internally compensated architecture that provides unity-gain stability without external compensation components. Single-supply or split-supply operation gives designers flexibility across 3.0 V to 26 V rails, and the input bias currents are low, minimizing offset errors with high-impedance sensors. Typical applications include automotive sensor signal conditioning (throttle position, pressure), battery-voltage monitoring dividers, comparators for window detection in ECUs, and general industrial signal amplification on single 5 V to 24 V rails. A key design consideration: the output cannot swing to the positive rail, so gain-setting must keep target output levels below the VOH specification at the expected load current. This page synthesizes distributor availability, drop-in alternatives across the LM258/LM358/LM2904 family, and practical design notes beyond what the manufacturer datasheet states.

RFQ צור קשר
NDL46PFG-8KIT - 4Gb DDR3L SDRAM 256Mx16 | Insignis
NDL46PFG-8KIT

NDL46PFG-8KIT - 4Gb DDR3L SDRAM 256Mx16 | Insignis

The NDL46PFG-8KIT is a 4Gbit DDR3L SDRAM organized as 256M x 16, operating at 800 MHz (DDR3L-1600) with a CAS latency of 20 ns. It is designed to comply with all key DDR3L DRAM features, with control and address inputs synchronized to a pair of externally supplied differential clocks. Inputs are latched at the cross point of differential clocks (CK rising and CK# falling), and all I/Os are synchronized with a differential DQS pair in a source-synchronous fashion. This device is available in a 96-ball FBGA package (7.5x13.5 mm) and supports a maximum operating temperature of 95°C. DDR3L SDRAM is a type of dynamic random-access memory that operates at a lower voltage (1.35V) compared to standard DDR3 (1.5V), reducing power consumption by up to 20% while maintaining high bandwidth. It is part of the DDR3 memory family, which is widely used in computing, networking, and embedded systems. The NDL46PFG-8KIT is compatible with both 1.5V and 1.35V supplies, offering flexibility in system design. Key features include a 4Gbit density, 16-bit data bus, 800 MHz clock speed (1600 Mbps data rate), and a 20 ns CAS latency. The device supports standard DDR3L features such as on-die termination (ODT), programmable CAS latency, and burst lengths of 8 and 4. It also includes auto-refresh and self-refresh modes for low-power standby. The architecture uses an 8n-prefetch design, enabling high-speed data transfer with reduced I/O clock frequency. The differential clock inputs (CK and CK#) and data strobes (DQS and DQS#) ensure robust signal integrity for high-speed operation. The 96-ball FBGA package provides excellent thermal and electrical performance, making it suitable for space-constrained applications. Typical applications include servers, networking equipment, industrial computing, and embedded systems requiring high-density, low-power memory. The 1.35V operation is ideal for power-sensitive designs, such as battery-powered devices and energy-efficient data centers. When designing with this device, ensure proper decoupling capacitors near the power pins and follow the layout guidelines in the datasheet to minimize signal integrity issues. The device supports a wide operating temperature range, making it suitable for industrial environments.

RFQ צור קשר
NE5532AD - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532AD

NE5532AD - Dual 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532AD is a dual, low-noise operational amplifier designed for audio applications, with a 10 MHz typical unity-gain bandwidth, 5 nV/√Hz typical input noise voltage at 1 kHz, and 100 dB typical high dc voltage gain. The device is supplied in an 8-pin SOIC package. It is unity-gain compensated and combines low noise, low distortion, high output-drive capability, and a typical 32 V peak-to-peak output voltage swing under ±18 V supply conditions. An operational amplifier is an active semiconductor device that uses high gain and negative feedback to amplify voltage differences between its inputs. The NE5532 belongs to the low-noise operational amplifier hierarchy, which sits within analog signal-chain ICs, integrated circuits, and semiconductor devices. Its dual-amplifier configuration provides two independent amplifiers in one package, reducing board area in audio preamplifiers, mixers, active filters, and signal-conditioning circuits. The principal audio-oriented characteristics are 5 nV/√Hz typical equivalent input noise voltage at 1 kHz and a 10 MHz typical unity-gain bandwidth. According to the Texas Instruments product description, the NE5532 is a dual 30 V, 10 MHz low-noise operational amplifier. The device also provides 100 dB typical high dc voltage gain, a 32 V typical peak-to-peak output swing with ±18 V supplies, and a typical slew rate of 600 V/µs. The NE5532x family is internally compensated for unity-gain operation, reducing the external compensation components normally required around a high-speed amplifier. Its dual architecture allows two amplifier channels to share one package while retaining the low-noise characteristics sought in audio paths. Input-protection diodes, output short-circuit protection, and a high output-drive capability are identified in the manufacturer datasheet, making the device suitable for conventional low-frequency audio and general analog applications. Typical uses include stereo audio preamplification, mixing consoles, headphone-driver stages, active equalization filters, low-level audio signal conditioning, and instrumentation requiring low input noise. The dual configuration is especially useful where two related channels are required, such as left and right program paths. Its 10 MHz bandwidth also provides more than enough bandwidth for conventional audio while retaining useful response for other precision low-noise signal-chain work. When designing around the NE5532AD, verify the required output swing, input common-mode range, supply voltage, and stability at the selected gain against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left with open inputs. Source and sink capability should also be checked when driving a transformer, headphone stage, or capacitive load. This product record combines verified manufacturer and distributor information with practical engineering guidance, package and pinout details, pricing references, and a qualification of available drop-in alternatives. The comparison and application sections emphasize where the NE5532AD fits and where the available source evidence does not support claiming a true same-package replacement.

RFQ צור קשר
NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi
NE5532AD8

NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi

The onsemi NE5532AD8 is a dual high-performance, internally-compensated low-noise operational amplifier supplied in an 8-pin SOIC (SO-8, "D8" suffix) surface-mount package. The device integrates two independent op-amp channels with input-protection diodes, output short-circuit protection, very low equivalent input noise voltage of about 5 nV/√Hz typical at 1 kHz, a high unity-gain bandwidth of 10 MHz, a 9 V/µs slew rate, and a 600 Ω drive capability, all from a single dual-supply rail of ±3 V to ±20 V (or single-supply 6 V to 40 V). An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. It is the fundamental analog building block inside audio preamplifiers, active filters, instrumentation stages, servo loops, ADC input buffers, and DAC output I/V converters. The NE5532 family belongs to the "low-noise audio" op-amp class — a category that improves upon generic parts such as the 1458 by combining low voltage noise, wide bandwidth, and strong output drive into one device. Key features include low harmonic distortion (typically 0.002 % at 1 kHz into 600 Ω), high output current that can drive 600 Ω headphone loads directly, large output voltage swing (≈ ±13 V on ±15 V supplies), and excellent channel separation around 110 dB at 1 kHz. The "A" suffix denotes the higher-precision NE5532A variant with tighter input-offset voltage (typically 0.5 mV versus 0.5 mV for the non-A) and improved AC characteristics versus the original NE5532, while remaining pin-compatible with the standard NE5532 socket. Architecturally, the NE5532A uses a bipolar-junction input stage with emitter-degeneration resistors, a PNP common-emitter second stage, and an NPN class-AB output stage. Compensation is built into the die (no external capacitor required), which simplifies PCB design but caps stable unity-gain operation. Designers should treat the device as a "single-supply-unfriendly" part when planning ground-referenced single-rail circuits; a mid-rail bias is required for true ground sensing. Typical applications include high-fidelity audio preamplifiers, mixing consoles, microphone preamps, RIAA phono stages, line drivers, active crossovers, test-instrumentation signal conditioners, and ADC/DAC interface buffers. The 8-pin SOIC footprint is well-suited to high-density PCB designs and is one of the most widely supported DIP-socket IC sockets on adapter boards. When designing with the NE5532AD8, derate output current with increasing junction temperature, mind the input common-mode range that does not include the negative rail, and provide a solid ground pour for the exposed copper pad of the SOIC to keep the junction temperature below 150 °C. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi
NE5532AD8G

NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi

onsemi NE5532AD8G is a dual, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and two amplifier circuits in an 8-pin SOIC package. It is intended for audio, instrumentation, and control applications where low noise and improved output drive are important. The device is specified for dual supplies of ±3 V to ±20 V and commercial-temperature operation. A dual operational amplifier combines two independent amplifiers in one package. The NE5532A family belongs to the operational-amplifier hierarchy, within analog signal-conditioning and active-control systems. Its internally compensated design simplifies use in non-inverting, inverting, and feedback configurations without an external compensation network, while its low-noise characteristics make it useful when signal integrity must be preserved through amplification. The verified NE5532AD8G data identifies a 10 MHz gain-bandwidth product, 9 V/µs slew rate, 200 nA input-bias current, 500 µV input-offset voltage, 8 mA supply current, and a 3 V to 20 V supply range in the distributor listing. The dual SOIC package provides two circuits in one component, reducing board area compared with separate single amplifiers. Its improved output-drive capability and small-signal bandwidth distinguish it from basic general-purpose dual op amps. Typical uses include stereo audio preamplification, mixer stages, active filters, microphone and line-level signal conditioning, test equipment, and industrial control circuits. In audio designs, the low-noise architecture helps preserve quiet signal paths, while the 9 V/µs slew rate supports higher-frequency transients when the circuit bandwidth and load permit. In instrumentation applications, the two amplifiers can process complementary or sequential channels. The primary design consideration is supply and load compatibility. Confirm the dual-supply range against the system rails, check input and output swing limits for the selected gain, and place decoupling capacitors close to the supply pins. Stable feedback-network layout, adequate output-current capability, and thermal margin should be checked against the actual signal amplitude and frequency. No SOA applies because this is a linear operational amplifier rather than a power semiconductor.

RFQ צור קשר