מעגלים משולבים

DSPIC33FJ64GS606-I/PT

DSPIC33FJ64GS606-I/PT - 16-bit DSC, 40 MIPS, 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS606-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33F GS family, delivering up to 40 MIPS at 3.3V with 64KB of Flash program memory, 9216 words of RAM, and a high-speed PWM module purpose-built for digital power conversion, housed in a 64-pin TQFP (10x10 mm) package with industrial -40C to +85C temperature grade. A digital signal controller combines the compute throughput of a DSP core with the deterministic peripheral set of a microcontroller. Within the power-management hierarchy, the DSC sits above a plain MCU for control-loop tasks: it executes Proportional-Integral-Derivative (PID) and predictive control loops for switch-mode power supplies (SMPS) at switching frequencies of hundreds of kilohertz, where a general-purpose MCU would struggle to close the loop within one PWM period. Hypernyms include DSC -> MCU -> embedded controller -> semiconductor. The GS sub-family is explicitly designed by Microchip for multi-loop digital SMPS topologies. Key features include a modified Harvard 16-bit DSP engine with single-cycle MAC and dual operand fetch, dedicated high-speed PWM peripherals with complementary outputs and dead-time control, high-speed analog-to-digital converters tightly coupled to the PWM for minimum loop latency, four DMA channels, multiple UART/SPI/I2C interfaces, and on-chip analog comparators that support cycle-by-cycle current limiting without external circuitry - essential for peak-current-mode converters. The architecture concurrently fetches two data operands from memory while multiplying two W registers and accumulating the result in a single cycle, per the Microchip datasheet. PWM resolution is configurable up to 16-bit at lower switching frequencies and the 4-input high-speed ADC supports up to 4 Msps throughput when the converter is switched. The comparator and PWM synchronization enables sub-microsecond hardware-level fault response. The /PT suffix denotes the 64-pin TQFP surface-mount package, while the -I suffix indicates industrial temperature grade. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), solar inverters, and digital welding power sources. Microchip's Interleaved PFC reference design, producing up to 350W from universal AC input, is based on this family. Design consideration: verify 3.3V rail sequencing before VDD reaches 5V at ICSP (PGECx/PGEDx) and trace length per the datasheet layout guidance. This page synthesizes verified distributor pricing, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ צור קשר

DSPIC33FJ64GS606T-50I/PT

DSPIC33FJ64GS606T-50I/PT - 16-bit 50MIPS DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS606T-50I/PT is a 16-bit digital signal controller (DSC) delivering 50 MIPS performance with 64KB of flash memory and 9KB of RAM, housed in a 64-pin TQFP (10x10 mm) surface-mount package rated for -40C to +85C industrial operation at 3.3V. A digital signal controller combines the computational throughput of a DSP core with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP, making it the preferred device class for closed-loop digital switch-mode power supplies (SMPS) where fast control loops, high-resolution PWM and on-chip analog are all mandatory. Key differentiating features of the GS606 include dedicated SMPS PWM modules with high resolution for precise duty-cycle control, two quadrature encoder interface (QEI) inputs for motor feedback, an on-chip CAN module for system communication, a DAC for reference generation, and four analog comparators for fast overcurrent and cycle-by-cycle protection. Per Microchip product data, the device enumerates as a 16-bit DSC with 64KB Flash, 9KB RAM, 50 MHz operation, SMPS PWM, 2 QEI, CAN, DAC and 4 comparators. Architecturally, the dsPIC33F core pairs a modified Harvard 16-bit pipeline with DSP multiply-accumulate instructions, allowing single-cycle MAC operations in control-loop interrupt service routines. The deep analog integration lets the GS606 close voltage and current loops entirely on-chip, reducing external component count and board area. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies, and digitally controlled lighting or motor-drive power stages, as cited on the Microchip dsPIC33FJ64GS606 product page. Design consideration: budget the PWM resolution against the instruction clock and verify comparator response times for your overcurrent trip threshold; the TQFP thermal pad-free package requires solid ground pours for high-frequency switching layouts. This page synthesizes distributor availability data, same-family drop-in options, and digital-power design notes not consolidated on the manufacturer product page.

RFQ צור קשר

DSPIC33FJ64GS606T-I/MR

DSPIC33FJ64GS606T-I/MR - 16-bit 40MIPS DSC 64KB | Microchip

The Microchip Technology DSPIC33FJ64GS606T-I/MR is a 16-bit digital signal controller (DSC) from the dsPIC33F GS family, delivering 40 MIPS performance with 64 KB (64K x 8) of program flash memory and 9216 words of RAM, housed in a 64-pin VQFN (MR) package with exposed thermal pad operating at 3.3V. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control flexibility of a microcontroller. Within the power-management hierarchy, a DSC sits above a standard MCU for closed-loop control tasks: it executes control loops fast enough for switch-mode power conversion while integrating specialized analog and timing peripherals on one die. Key features include a high-speed PWM module purpose-built for digital switch-mode power supplies (SMPS), a high-speed 10-bit ADC with multiple sample-and-hold circuits for simultaneous multi-rail sampling, analog comparators, and four DMA channels. The device supports In-Circuit Serial Programming (ICSP) and debugging via PGECx/PGEDx pins, plus boundary-scan capability and low-power modes. Technically, the dsPIC33FJ64GS606 core pairs a 16-bit modified Harvard architecture with DSP engine instructions (fixed-point format, barrel shifter), letting a single device run a PFC loop and downstream DC-DC loops concurrently. Peripheral pin-select and rich timer resources reduce external glue logic in compact power supplies. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies, and digital lighting ballasts. The GS family was explicitly designed by Microchip for these multi-loop digital power-conversion applications. Design consideration: keep the ICSP connector trace lengths to PGECx/PGEDx as short as possible for reliable in-circuit debugging, and verify that the 40 MIPS grade (-I, industrial temperature) matches your switching-frequency headroom; a 50 MIPS variant exists if more loop bandwidth is required. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not consolidated in the manufacturer datasheet.

RFQ צור קשר

DSPIC33FJ64GS606T-I/PT

DSPIC33FJ64GS606T-I/PT - 16-bit DSC 40MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS606T-I/PT is a 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from 64KB of Flash program memory with 9KB of RAM, housed in a 64-lead TQFP (10x10 mm) surface-mount package operating from a 3.3V supply. A Digital Signal Controller combines the computational power of a digital signal processor with the peripheral integration and control architecture of a microcontroller, sitting between an MCU and a DSP in the embedded hierarchy. In the digital power domain, DSCs replace analog control loops with firmware-executed PID compensators, enabling programmable, adaptive switch-mode power supplies. The GS606 variant is purpose-built for digital power conversion: it integrates a high-speed PWM module with multiple output pairs, complementary outputs, dead-time control, and fault inputs, alongside a high-speed 10-bit ADC with simultaneous multi-channel sampling and analog comparators. These peripherals allow a single device to close both the fast inner current loop and the slower outer voltage loop in SMPS topologies. The device also provides 8 timers, 4 DMA channels, and serial communication interfaces (UART, SPI, I2C) per the distributor-listed feature set. Architecturally, the dsPIC33F core uses a 16-bit modified Harvard pipeline with DSP instructions (MAC, multiply) and two 40-bit accumulators, sustaining 40 MIPS operation. In-Circuit Serial Programming (ICSP) via PGECx/PGEDx pins supports field updates, and Microchip recommends short ICSP traces on the PCB. Typical applications include AC-DC converters, DC-DC converters, Power Factor Correction (PFC) stages, uninterruptible power supplies (UPS), solar inverters, LED drivers, and high-performance motor control, where high-speed analog acquisition and flexible PWM are mandatory. For design, budget the 3.3V rail carefully and route PWM outputs with controlled edge rates to limit switching-node ringing; dead-time settings must be validated against MOSFET gate-charge specifications to prevent shoot-through. This page synthesizes verified distributor listings, datasheet-family cross references, and digital-power design guidance not consolidated on typical catalog pages.

RFQ צור קשר

DSPIC33FJ64GS608-50I/PT

DSPIC33FJ64GS608-50I/PT - 16-bit 50MIPS DSC | Microchip

The Microchip Technology DSPIC33FJ64GS608-50I/PT is a 16-bit digital signal controller (DSC) combining MCU ease of use with DSP performance, delivering 50 MIPS from a dsPIC33F core with 64KB (64K x 8) Flash program memory and 9KB RAM, housed in an 80-pin TQFP (12x12 mm) package. A digital signal controller is a hybrid semiconductor that merges the control peripherals of a microcontroller with the computational throughput of a digital signal processor. Within the power-management semiconductor hierarchy, the DSC sits above general-purpose MCUs and below dedicated DSPs, making it the preferred controller class for closed-loop digital power conversion where fast, deterministic control loops are required. Key differentiating features include the high-speed PWM module with special SMPS operating modes, a high-speed 10-bit ADC with multiple sample-and-hold circuits, and on-chip analog comparators - a peripheral set purpose-built for multi-loop digital switch-mode power supplies (SMPS). The device also provides 2 QEI modules, a CAN controller, DAC outputs, and 4 DMA channels for efficient data movement. Architecturally, the dsPIC33F core executes DSP instructions (MAC, barrel shifter) with dual operands fetched in a single cycle, enabling digital filter algorithms and high-precision control-loop computations at 50 MIPS. Extended-temperature variants such as the /50E grade and industrial (-40C to +85C) /50I grade share the same die and peripheral map. Typical applications include AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), and digital lighting or battery-charging power stages. Design consideration: connect every VDD/VSS pair and pair PGECx/PGEDx consistently for ICSP programming - the device has multiple ICSP pin pairs that must be used as matched pairs. This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-09-27.

RFQ צור קשר

DSPIC33FJ64GS608-I/PT

DSPIC33FJ64GS608-I/PT - 16-bit DSC 40MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS608-I/PT is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS performance with 64KB (64K x 8) of Flash program memory, operating from a 3V to 3.6V supply in an 80-pin TQFP (12x12 mm) surface-mount package rated from -40C to +85C. A Digital Signal Controller combines the compute throughput of a Digital Signal Processor (DSP) with the peripherals, ease of use, and interrupt structure of a microcontroller (MCU). Within the power-management hierarchy, the dsPIC33F GS family sits at the controller layer of a digital switch-mode power supply (SMPS), executing the control loop that a dedicated analog controller would otherwise implement in hardware. The GS series is purpose-built for digital power conversion: it integrates high-speed PWM peripherals, high-speed ADC and analog comparators, the core building blocks for multi-loop SMPS control. According to Microchip product documentation, these devices support AC-to-DC converters, DC-to-DC converters, Power Factor Correction (PFC), and uninterruptible power supplies (UPS). The 40 MIPS dsPIC33F core is designed to execute digital filter algorithms, high-speed precision digital control loops, and digital audio and speech processing. Its DSP engine supports MAC-class instructions that enable the tight, deterministic loop timing required by peak-current-mode and voltage-mode converters switching at hundreds of kilohertz. In-Circuit Serial Programming (ICSP) via PGECx/PGEDx pin pairs allows field firmware updates without removing the device from the board. Typical applications include interleaved PFC front ends (Microchip publishes a 350W interleaved PFC reference design for this family), telecom and server DC-DC bricks, solar micro-inverters, UPS inverter control, and battery chargers. Design consideration: all VDD/VSS pairs must be decoupled and connected, and the ICSP PGECx/PGEDx pair must be routed as a matched pair with short traces to the programming connector; using PGEC2 for ICSPCLK requires PGED2 for ICSPDAT. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in family alternatives, cross-reference guidance, and practical design notes in one place.

RFQ צור קשר

DSPIC33FJ64GS608T-50I/PT

DSPIC33FJ64GS608T-50I/PT - 16-bit DSC 50MIPS 64KB | Microchip

The Microchip Technology DSPIC33FJ64GS608T-50I/PT is a 16-bit digital signal controller (DSC) delivering 50 MIPS performance with 64KB of Flash memory and 9KB of RAM, housed in an 80-pin TQFP surface-mount package rated for -40C to +85C operation from a 3V to 3.6V supply. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control-friendly architecture of a microcontroller. Within the power-management hierarchy, the dsPIC33FJ GS family sits above generic MCUs for digital power tasks: its instruction set supports fast PID and compensator loops, while dedicated high-speed PWM hardware closes control loops without CPU intervention. This makes DSCs the de-facto standard for digitally controlled switch-mode power supplies and power factor correction stages. Key features include dedicated high-speed PWM peripherals with complementary outputs, dead-time control and fault protection tailored for SMPS topologies; on-chip high-speed ADC modules synchronized to the PWM for cycle-by-cycle sampling; multiple analog comparators for overcurrent and overvoltage protection; CAN for industrial communication; DAC channels and QEI inputs for motion-oriented power conversion. The 50 MIPS core executes one instruction per cycle, allowing multi-loop control schemes in a single device. Architecturally, the device uses a modified Harvard 16-bit core with DSP multiply-accumulate instructions, separate program and data buses, and hardware looping. The Flash-based program memory supports in-circuit self-programming, and the supply range of 3.0V to 3.6V matches standard 3.3V rails. According to Microchip product documentation, the family explicitly targets AC to DC converters, DC to DC converters, power factor correction, and uninterruptible power supplies. Typical applications include digitally controlled AC-DC power supplies, interleaved PFC front ends, DC-DC converters, UPS systems, solar inverters, battery chargers, and LED drivers, where the PWM-ADC-comparator pipeline handles fast current-mode control while the CPU executes slower voltage and system loops. Design consideration: keep the 3.3V supply within the 3.0V to 3.6V window, decouple all VDD/VDDCORE pins with low-ESR ceramics close to the TQFP, and route PWM outputs away from analog ADC inputs to preserve conversion accuracy. This page synthesizes distributor pricing, drop-in alternatives, design notes, and comparison data not found on the manufacturer product page alone.

RFQ צור קשר

DSPIC33FJ64GS610-50I/PT

DSPIC33FJ64GS610-50I/PT - 16-bit DSC 50MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS610-50I/PT is a 16-bit digital signal controller (DSC) delivering 50 MIPS performance with 64KB Flash program memory and 9KB RAM, housed in a 100-pin TQFP (12x12 mm) package with industrial temperature rating of -40C to +85C. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and control architecture of a microcontroller. Within the power management hierarchy, DSCs such as the dsPIC33FJ64GS610 sit between general-purpose MCUs and dedicated power controllers, providing deterministic execution for closed-loop switch-mode power supply (SMPS) control loops running at hundreds of kilohertz. Key features include a dedicated SMPS PWM module optimized for power conversion, four high-speed comparators, an on-chip DAC, two quadrature encoder interfaces (QEI), a CAN 2.0B controller, and four DMA channels. The 16-bit modified Harvard architecture includes DSP engine instructions (MAC, barrel shifter) enabling fast execution of proportional-integral control algorithms without external assistance. The device is designed specifically for digital power applications: the high-resolution PWM module supports complementary outputs, dead-time insertion, and fault protection required by LLC, half-bridge, full-bridge, and boost topologies. IEEE 1149.2-compatible JTAG boundary scan and In-Circuit Serial Programming (ICSP) via PGECx/PGEDx pins simplify production programming and board-level test. Typical applications include interleaved power factor correction (PFC), digital AC-DC and DC-DC converters, solar inverters, battery chargers, UPS systems, and industrial motor drives where sensor feedback loops demand DSP-class throughput. For design, keep ICSP trace lengths short per the Microchip datasheet recommendation, and budget the 3.3V supply with adequate decoupling across the 100-pin TQFP. This page consolidates verified specifications, drop-in alternatives, application guidance, and distributor sourcing data in one place - information not assembled in the manufacturer datasheet alone.

RFQ צור קשר

DSPIC33FJ64GS610-E/PT

DSPIC33FJ64GS610-E/PT - 16-bit 40MIPS DSC, 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS610-E/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS of performance with 64 KB (64K x 8) of Flash program memory, packaged in a 100-pin TQFP (PT, 12x12 mm) surface-mount form factor. It operates from a 3.0 V to 3.6 V supply and is rated for the extended temperature range of -40C to +125C, and is part of the AEC-Q100-capable dsPIC33FJ64GS610 SMPS family. A digital signal controller (DSC) combines the computational throughput of a DSP with the peripheral integration and control architecture of a microcontroller. Within the embedded power-management hierarchy, a DSC sits at the top of the digital control chain: it executes closed-loop control firmware that drives power stages such as PFC boost stages, full-bridge DC-DC converters, and photovoltaic inverters, replacing legacy analog compensators with deterministic software compensation. Key features include the high-speed SMPS-optimized PWM module with complementary outputs and programmable dead time, a 10-bit high-speed ADC capable of simultaneous multi-channel sampling for current- and voltage-loop acquisition, and integrated analog comparators for cycle-by-cycle current limiting. The -E temperature grade and AEC-Q100 association make the part suitable for harsh industrial and automotive-adjacent environments, while 40 MIPS of 16-bit DSP throughput with single-cycle hardware multiply accelerates the current-loop execution that determines converter bandwidth. The architecture targets multi-loop digital power conversion: the PWM and ADC modules are tightly coupled so that ADC conversion triggers can be synchronized to PWM edges, minimizing control-loop latency. Four DMA channels, JTAG boundary-scan debug, and a rich interrupt structure round out the system integration expected for power-conversion firmware. Typical applications include AC-DC converters, isolated DC-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), and solar micro-inverters, where the high-speed PWM resolution directly improves converter efficiency and transient response. Design consideration: this is a 3.3 V core part - confirm the 3.0-3.6 V supply range fits your power tree, and budget Flash/RAM headroom because 64 KB program Flash and the RAM partition are fixed for this SKU. Verify MSL handling for the TQFP package before reflow. This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר

DSPIC33FJ64GS610-I/P

DSPIC33FJ64GS610-I/P - 16-bit DSC 40MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS610-I/P is a high-performance 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from a 64 KB Flash program memory and 9216 words of RAM, supplied at 3.0V to 3.6V and housed in a 100-pin TQFP (14x14 mm, 0.4 mm pitch) surface-mount package. A Digital Signal Controller combines the compute throughput of a DSP engine with the peripheral integration and deterministic control of a microcontroller. Within the power-management semiconductor hierarchy, a DSC sits above a general-purpose MCU for closed-loop control tasks and below a full application processor, occupying the sweet spot for real-time switch-mode power supply (SMPS) control loops that require fast, cycle-accurate PWM and ADC interaction. Key features include a dedicated high-speed PWM module with complementary outputs and dead-time control, a high-speed 10/12-bit ADC, and integrated analog comparators - the exact peripheral trio required for voltage-mode, current-mode, and multi-loop digital power conversion. The device also provides In-Circuit Serial Programming (ICSP), in-application programming, two program and two complex data breakpoints, and IEEE 1149.2-compatible (JTAG) boundary scan for production test. Architecturally, the dsPIC33FJ GS family couples a 16-bit modified Harvard core with DSP multiply-accumulate instructions, allowing single-cycle MAC operations for filter and control-law computation. Industrial operating temperature (-40C to +85C) and a CMOS process support demanding embedded environments. Typical applications include AC-DC converters, DC-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), and solar/LED power systems where deterministic multi-loop control is mandatory. For design, place the ICSP connector traces (PGECx/PGEDx) as short as possible, per the Microchip datasheet, and pair any PWM/ADC pin usage with proper analog grounding around the comparators. This page adds value beyond the manufacturer datasheet by synthesizing distributor availability data, same-package drop-in alternatives, practical design notes, and pricing context in one citable reference.

RFQ צור קשר

DSPIC33FJ64GS610-I/PF

DSPIC33FJ64GS610-I/PF - 16-bit DSC 40 MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS610-I/PF is a high-performance 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from a CMOS core with 64KB (64K x 8) of FLASH program memory and 9216 words of RAM, housed in a 100-pin TQFP (14x14 mm, 0.4 mm terminal pitch) surface-mount package. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and deterministic control of a microcontroller. Within the power-management IC hierarchy, a DSC sits above a general-purpose MCU for closed-loop control tasks: it samples feedback with fast analog-to-digital converters, executes control-loop mathematics, and drives power stages through dedicated PWM hardware. The dsPIC33F family is Microchip's 16-bit DSC platform, and the GS series is its switch-mode power supply (SMPS) optimized subset. Key features of the DSPIC33FJ64GS610 include the 40 MIPS 16-bit core, 64KB self-programming FLASH, 3.0V to 3.6V single-supply operation, industrial temperature rating (-40C to +85C), and peripheral sets purpose-built for digital power: high-resolution PWM modules, fast analog comparators and ADCs for current-mode control, plus multiple UART, SPI and I2C ports for supervisory communication. In-Circuit Serial Programming (ICSP) via PGECx/PGEDx pin pairs enables field firmware updates. Architecturally, the device pairs a 16-bit modified Harvard core with DSP instructions (MAC, DSP multiply) so that proportional-integral and predictive control loops execute in single-microsecond budgets, a decisive advantage over software-timed 8-bit MCUs in converters switching at 100 kHz and above. Typical applications include AC-DC converters, DC-DC converters, power factor correction (PFC) stages - including interleaved PFC reference designs up to 350W - and uninterruptible power supplies (UPS), where the SMPS-focused peripherals directly implement voltage-mode, current-mode and multi-loop control. Design consideration: use a PGECx/PGEDx pair consistently (for example PGEC2 with PGED2) for ICSP and debugging, and keep ICSP traces short per the Microchip datasheet layout guidance. This page synthesizes distributor pricing, pin-compatible family alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-09-27.

RFQ צור קשר

DSPIC33FJ64GS610T-50I/PF

DSPIC33FJ64GS610T-50I/PF - 16-bit 50MIPS DSC 64KB Flash | Microchip

The Microchip DSPIC33FJ64GS610T-50I/PF is a 16-bit dsPIC33F digital signal controller (DSC) delivering 50 MIPS performance with 64KB (64K x 8) FLASH program memory and 9KB RAM, housed in a 100-pin TQFP (14x14 mm) surface-mount package. A digital signal controller combines the control flow of a microcontroller (MCU) with the computational throughput of a digital signal processor (DSP) in a single device. Within the power-management hierarchy, a DSC such as the dsPIC33FJ64GS610 sits between a general-purpose MCU and a dedicated digital power IC, executing real-time control loops for switching power supplies and motor drives while also managing housekeeping, communication, and user-interface tasks. Key differentiating features include dedicated SMPS PWM peripherals, 2 quadrature encoder interface (QEI) modules, a CAN 2.0B controller, a 10-bit DAC, and 4 analog comparators, making this one of the few 16-bit controllers purpose-built for digital power conversion. The industrial temperature grade (-40C to +85C, denoted by the I suffix) suits demanding factory and power-infrastructure environments. Architecturally, the dsPIC33F core pairs a 16-bit pipelined CPU with DSP instruction extensions (single-cycle MAC, dual operand fetch), enabling deterministic execution of Proportional-Integral-Derivative (PID) and predictive control loops at loop rates far above what conventional MCUs achieve. High-resolution PWM modules support complementary outputs, dead-time insertion, and fault shutdown - the classic requirements of half-bridge and full-bridge power stages. Typical applications include switched-mode power supplies (SMPS) with active Power Factor Correction, DC-DC converters, digital lighting ballasts, and battery chargers. Microchip's Interleaved PFC reference design, delivering up to 350W from a universal input range, is based directly on this device family. When designing with this part, budget the peripheral pin map early - the 100-pin TQFP provides the port fan-out needed for multiple PWM channels plus CAN and QEI simultaneously, but remappable pin assignment must be planned to avoid routing conflicts. This page synthesizes distributor pricing context, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet. Pricing references are as of 2026-09-27.

RFQ צור קשר

DSPIC33FJ64GS610T-50I/PT

DSPIC33FJ64GS610T-50I/PT - 16-bit 50MIPS DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64GS610T-50I/PT is a 16-bit digital signal controller (DSC) delivering up to 50 MIPS from a dsPIC33F core, with 64KB of FLASH program memory and 9KB of RAM, housed in a 100-pin TQFP (12x12 mm) package rated from -40C to +85C at 3.0V to 3.6V operation. A digital signal controller combines the compute throughput of a DSP engine (single-cycle MAC, DSP multiply, hardware divide support) with the deterministic control peripherals of a microcontroller. Within the power-management hierarchy, the dsPIC33FJ64GS610 belongs to Microchip's SMPS-focused family: DSC -> digital signal controller -> 16-bit MCU -> embedded processor, purpose-built to close multi-loop digital control of switch-mode power supplies in software. Key features include a high-speed PWM module with complementary outputs, dead-time insertion and fault protection, a high-speed 10-bit ADC with multiple sample-and-hold circuits able to trigger from the PWM, four analog comparators, two QEI (quadrature encoder interface) modules, a CAN 2.0B controller, and on-chip DAC outputs. These peripherals map directly onto PFC stage, phase-current, and bus-voltage sensing with minimal external circuitry. Architecturally, the 16-bit pipelined core executes C-efficient code with DSP instructions, while the ADC-PWM loop timing in the low hundreds of nanoseconds enables high-bandwidth current-mode control for LLC, half-bridge, and interleaved topologies. Internal fast RC oscillators and PLL allow 50 MIPS operation without an external crystal in cost-sensitive designs. Typical applications include AC-DC converters, DC-DC converters, power factor correction, uninterruptible power supplies, solar inverters, and digital lighting ballasts, where the integrated SMPS peripherals replace discrete analog control loops. Design consideration: the ADC sampling window and PWM dead-time registers must be co-scheduled; use the datasheet trigger scheme to avoid sampling during switching transients. This page synthesizes verified distributor data, drop-in alternatives, and design guidance not found on a single manufacturer or distributor page.

RFQ צור קשר

DSPIC33FJ64GS610T-I/PF

DSPIC33FJ64GS610T-I/PF - 16-bit DSC 40MIPS 64KB | Microchip

The Microchip Technology DSPIC33FJ64GS610T-I/PF is a 16-bit digital signal controller (DSC) delivering 40 MIPS from 64 KB (64K x 8) of flash memory with 9 KB RAM, housed in a 100-pin TQFP (14x14 mm) package. A digital signal controller combines the computational throughput of a digital signal processor with the deterministic control peripherals of a microcontroller. Within the power-management IC hierarchy, the dsPIC33F GS family occupies the role of a dedicated digital power conversion engine, replacing analog loop control with firmware-executed compensation in switch-mode power supply (SMPS) systems. Key features of this device include dedicated high-resolution SMPS PWM modules, two quadrature encoder interfaces (QEI), a CAN controller, four on-chip comparators, and DAC-based analog comparators tailored for multi-loop power conversion. These peripherals enable AC-to-DC converters, DC-to-DC converters, power factor correction (PFC) stages, and uninterruptible power supply (UPS) designs on a single controller. The dsPIC33F core executes an enhanced 16-bit instruction set with DSP instructions, a barrel shifter, four DMA channels, and boundary-scan (JTAG) support for production programming and debugging. In-circuit serial programming (ICSP) uses the PGECx/PGEDx pin pairs, and Microchip recommends keeping ICSP trace lengths short on high-speed power boards. Typical applications include interleaved PFC front ends (Microchip's 350 W universal-input interleaved PFC reference design uses this family), telecom rectifiers, solar micro-inverters, battery chargers, and embedded motor-drive control where deterministic 40 MIPS control loops are required. Design consideration: the -I temperature suffix covers -40C to +85C industrial operation; if extended temperature range to +125C is required, use the -E suffix variant, which shares the same die and TQFP footprint. This page adds value beyond the datasheet by synthesizing distributor pricing across 9 sources, drop-in alternatives within the same 100-TQFP footprint, and practical digital-power design notes not found on the Microchip product page.

RFQ צור קשר

DSPIC33FJ64GS610T-I/PT

DSPIC33FJ64GS610T-I/PT - 40MIPS 16-bit DSC for Digital Power | Microchip

The Microchip Technology DSPIC33FJ64GS610T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33FJ64GS610 SMPS family, delivering up to 40 MIPS of dsPIC core performance with 64KB (64K x 8) of FLASH program memory and 9KB of RAM, housed in a 100-pin TQFP (12x12 mm) surface-mount package operating from a 3.3 V supply across an industrial temperature range of -40C to +85C. A digital signal controller combines the computational throughput of a 16-bit microcontroller with DSP-grade math acceleration, making the dsPIC33F family a staple of digital switch-mode power supply (SMPS) design, where a single chip closes current and voltage control loops in firmware while driving PWM stages directly. Within the power-management semiconductor hierarchy, the DSPIC33FJ64GS610 sits in the digital power conversion segment between general-purpose MCUs and dedicated DSPs. Key features include a high-speed PWM module purpose-built for power conversion, a high-speed 10-bit and 12-bit ADC with simultaneous multi-channel sampling for multi-loop control, and integrated analog comparators for cycle-by-cycle current limiting. The device supports 40 MHz input clocking (40 MIPS operation per Microchip USA product data), and the tape-and-reel (/T) suffix supports automated SMT assembly lines. The architecture pairs the dsPIC33F 16-bit RISC core with DSP multiply-accumulate instructions and hardware loop support, enabling deterministic single-cycle MAC execution that keeps PFC and phase-shifted control loops stable at high switching frequencies. An In-Circuit Serial Programming (ICSP) interface via PGECx/PGEDx pins allows field firmware updates with only two dedicated pins, which Microchip recommends keeping as short traces to the programming connector. Typical applications include AC-to-DC converters, DC-to-DC converters, Power Factor Correction (PFC) stages, uninterruptible power supplies (UPS), solar inverters, and battery chargers. The Interleaved PFC reference design from Microchip demonstrates 350 W output from a universal AC input using this controller family. Design consideration: budget the PCB footprint carefully - the 100-pin TQFP (12x12 mm, 0.5 mm pitch) requires controlled-impedance-aware layout for the PWM outputs, and the extended-temperature -E/PT variant is required instead if -40C to +125C ambient is needed. This page synthesizes distributor pricing, drop-in same-family alternatives, applications, and design guidance not found in a single manufacturer source.

RFQ צור קשר

DSPIC33FJ64MC202-E/MM

DSPIC33FJ64MC202-E/MM - 16-bit DSC 40MIPS 64KB Flash QFN-28 | Microchip

The Microchip Technology DSPIC33FJ64MC202-E/MM is a 16-bit digital signal controller (DSC) delivering up to 40 MIPS with 64 KB of Flash program memory and 8 KB of SRAM, housed in a 28-pin VQFN (MM) package measuring 6 x 6 x 0.9 mm with an exposed pad. It operates from a 3.3 V supply across the extended industrial temperature range of -40C to +125C and carries AEC-Q100 automotive qualification. A digital signal controller combines the peripheral set and ease of use of a microcontroller with the computational throughput of a DSP engine. In the power-management hierarchy, a DSC sits between general-purpose MCUs and dedicated DSPs: it executes deterministic control loops (PID, field-oriented control) while simultaneously handling communication, sequencing, and housekeeping tasks. This makes DSCs the de-facto controller class for digitally controlled power conversion and motion systems. Key features of the DSPIC33FJ64MC202-E/MM include its 40 MIPS 16-bit modified Harvard architecture core with DSP multiply-accumulate instructions, dedicated motor-control PWM peripherals designed for three-phase inverter drives, up to 8 DMA channels that move data without CPU intervention, and 5 timers for multi-rate control loops. According to Microchip, the dsPIC33F family is pin compatible with the PIC24HJ family and shares a very high degree of compatibility with dsPIC30F devices, enabling seamless migration between families. Technically, the device integrates an on-chip high-speed analog front end (the MC variant targets the advanced-analog motor control market), barrel shifter, modulo and bit-reversed addressing for FFT algorithms, and dual inline Flash/SRAM buses that allow instruction fetch and data access in the same cycle. The extended-temperature E suffix supports thermally demanding automotive and industrial environments, while the QFN exposed-pad package improves heat transfer to the PCB. Typical applications include brushless DC and permanent-magnet synchronous motor drives, digital power supplies ( LLC, totem-pole PFC), solar micro-inverters, and embedded control in automotive auxiliary systems. The motor-control PWM with complementary outputs and dead-time insertion directly maps onto half-bridge topologies. Design-wise, plan the 3.3 V rail with adequate decoupling on both VDD pins and solder the exposed thermal pad to a ground pour for lowest junction-to-ambient impedance. Note that achieving the 40 MIPS ceiling requires the internal PLL from the oscillator source. This page synthesizes distributor pricing from Mouser, DigiKey, LCSC and Newark, same-package drop-in alternatives, and practical design notes that go beyond the raw datasheet listing.

RFQ צור קשר

DSPIC33FJ64MC202-E/SP

DSPIC33FJ64MC202-E/SP - 16-bit DSC 64KB Flash 40MIPS | Microchip

The Microchip Technology DSPIC33FJ64MC202-E/SP is a 16-bit digital signal controller (DSC) delivering 40 MIPS from 64KB (64K x 8) of Flash memory, housed in a 28-pin SPDIP through-hole package and rated for -40C to +125C operation at 3V to 3.6V supply. A digital signal controller combines the computational architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. In the product hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it executes high-speed, repetitive multiply-accumulate loops for control mathematics while integrating motor-control PWM, high-speed ADC, and DMA peripherals on one chip. The dsPIC33F family from Microchip Technology is pin compatible with the PIC24HJ family, giving designers a migration path between general-purpose and DSP-centric pinouts. Key features of the DSPIC33FJ64MC202-E/SP include the 16-bit modified Harvard dsPIC core clocked at up to 40 MIPS, 64KB Flash program memory with self-programming capability, motor-control PWM modules targeted at three-phase and BLDC drives, a direct memory access (DMA) controller that offloads ADC and UART data transfers from the CPU, and advanced analog peripherals for current and voltage sensing. The -E extended temperature grade (-40C to +125C) supports industrial and automotive-adjacent environments. Technically, the 16-bit RISC architecture uses two 40-bit accumulators and hardware DSP multiply-accumulate instructions, enabling single-cycle MAC operations for FOC (field-oriented control), PID loops, and digital filtering. The wide 28-pin SPDIP package suits breadboarding, prototyping, education, and legacy through-hole production where hand soldering and socketing matter. Typical applications include brushless DC and permanent-magnet motor control, digital power supplies and PFC stages, sensor signal conditioning with on-chip filtering, and industrial instrumentation requiring deterministic 40 MIPS control loops. Design consideration: the dsPIC33F core requires a VCAP/VDDCORE capacitor on the internal regulator output pin, and the supply must remain within 3.0V-3.6V; the on-board regulator simplifies 3.3V rail design but this capacitor must never be omitted. This page synthesizes distributor pricing, drop-in family alternatives, pinout detail, and practical design notes not consolidated in the manufacturer datasheet. Pricing references LCSC data as of 2026-09-27 (from $5.8868, in stock).

RFQ צור קשר

DSPIC33FJ64MC202-I/MM

DSPIC33FJ64MC202-I/MM - 16-bit DSC 40MIPS 64KB Flash QFN-28 | Microchip

The Microchip Technology DSPIC33FJ64MC202-I/MM is a 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from a 64 KB Flash program memory and 8 KB SRAM, housed in a 28-pin QFN-S (MM) 6x6 mm surface-mount package with exposed pad, rated for -40C to +85C industrial operation at 3.3V. A Digital Signal Controller combines the compute architecture of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller unit (MCU). DSCs sit within the broader embedded processor hierarchy between general-purpose MCUs and dedicated DSPs, and are optimized for control loops that rely on high-speed, repetitive computations such as motor control, digital power conversion, and sensor signal processing. Key features include the dsPIC33F 16-bit core with DSP engine (17-bit x 17-bit multiplier, 40-bit accumulator, dual operand fetch), Motor Control PWM, 8 DMA channels, 5 timers, 2 serial I/O ports supporting UART, SPI and I2C, and an advanced analog block with a 10-bit ADC. According to the Microchip product page, the dsPIC33F family is pin compatible with the PIC24HJ family and shares a high degree of compatibility with dsPIC30F devices, enabling seamless migration. Technical depth: the modified Harvard architecture with multiple internal buses allows concurrent instruction fetch and data access, while hardware looping and bit-reversed addressing accelerate FFT and filter kernels. CMOS process operation at 3.3V keeps power manageable, and ICSP/ICD programming via PGECx/PGEDx pairs supports in-circuit debugging with Microchip tools such as MPLAB and PICkit/ICD programmers. Typical applications include brushless DC and PMSM motor control, digital power supplies and PFC stages, audio processing, and industrial sensor interfaces - all domains where deterministic 40 MIPS DSP throughput and dedicated PWM peripherals are decisive. Design consideration: pin-compatible migration within the family lets you scale Flash (16-64 KB) without PCB changes, but verify VCAP/VDDCORE capacitor requirements on all layouts. This page synthesizes distributor pricing, drop-in alternatives, pinout detail, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר

DSPIC33FJ64MC202-I/SO

DSPIC33FJ64MC202-I/SO - 16-bit DSC 40MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64MC202-I/SO is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance with 64 KB of Flash program memory and DMA, housed in a 28-pin SOIC (SO) package rated for -40C to +85C operation. A digital signal controller combines the computational throughput of a digital signal processor with the deterministic control peripherals of a microcontroller. Within the power-management hierarchy, a DSC sits above a general-purpose MCU: it adds a DSP engine, hardware multiply-accumulate (MAC) instructions, and motor-control PWM peripherals, making the dsPIC33F family a staple in closed-loop power electronics where firmware must execute proportional-integral control loops at tens of kilohertz. Key features of the DSPIC33FJ64MC202 include the 16-bit modified Harvard architecture with DSP instruction support, up to 40 MIPS operation from an internal PLL, DMA channels for peripheral-to-memory transfers without CPU intervention, and a rich analog block. Per the dsPIC33FJ64MC202 datasheet family documentation (460-page family reference covering up to 128 KB Flash and 16 KB SRAM variants), the device integrates a 10/12-bit ADC, comparators, and motor-control PWM outputs suited to three-phase inverter drive. Technically, the dsPIC33F core operates from a 3.0V to 3.6V supply, provides 21 I/O ports in the 28-pin version, and is pin compatible with the PIC24HJ family, allowing seamless migration between Microchip 16-bit platforms. Flash-based program memory supports in-circuit serial programming (ICSP) via PGEC/PGD pin pairs, simplifying field updates. Typical applications include brushless DC and permanent-magnet synchronous motor control, switch-mode power supplies and digital power factors correction, and digital audio or sensor signal processing where repetitive MAC-intensive loops dominate. Design-wise, budget the 3.0-3.6V rail early; the device is not 5V tolerant across all pins, and decouple all VDD/AVDD pairs with 0.1 uF ceramics placed within 5 mm of the pins. This page synthesizes distributor inventory, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-09-27.

RFQ צור קשר

DSPIC33FJ64MC202-I/SP

DSPIC33FJ64MC202-I/SP - 16-bit DSC 40MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64MC202-I/SP is a 16-bit Digital Signal Controller (DSC) delivering 40 MIPS performance, 64KB (64K x 8) of Flash program memory, and a 3V to 3.6V supply range, housed in a 28-pin SPDIP through-hole package. A Digital Signal Controller combines the computational architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs, providing hardware multiply-accumulate (MAC) and DSP instruction support for high-speed, repetitive computations such as control loops and filtering. The dsPIC33F family is Microchip's 16-bit DSC line, and this device is pin compatible with the PIC24HJ family, according to Microchip's official product page. Key features include the 40 MIPS dsPIC33F core, 64KB self-programming Flash, DMA capability for data movement without CPU intervention, and an advanced analog and Motor Control PWM peripheral set designed for digital power conversion. According to DigChip datasheet data, the part is ACTIVE in life cycle, specified from 3V to 3.6V, and offered in lead-free packages. Architecturally, the dsPIC33F employs a modified Harvard 16-bit core with DSP engine, supporting high-speed, repetitive computation workloads. The DMA controller offloads peripherals, sustaining deterministic real-time behavior in closed-loop control systems while the CPU bandwidth remains available for application logic. Typical applications include switch-mode power supplies, digital power supplies, motor control (BLDC, PMSM, AC induction), and power inverters, where the Motor Control PWM and fast ADC sampling align directly with control-loop requirements. Design consideration: the 28-pin SPDIP is through-hole, ideal for prototyping and education, but verify decoupling - place 0.1uF ceramics close to all VDD/VSS pin pairs and pair PGECx/PGEDx pins correctly for ICSP programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר

DSPIC33FJ64MC202T-I/SO

DSPIC33FJ64MC202T-I/SO - 16-bit 40MIPS DSC, 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64MC202T-I/SO is a 16-bit digital signal controller (DSC) delivering up to 40 MIPS performance with 64KB (64K x 8) of Flash program memory and DMA, housed in a 28-pin SOIC (SO) surface-mount package. It operates from a 3.0V to 3.6V supply at the industrial temperature range (-40C to +85C). A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice when high-speed, repetitive computations such as control-loop math must coexist with general I/O and communication tasks. Key features include a 16-bit modified Harvard architecture executing at 40 MIPS, a DSP engine with a high-speed 17-bit x 17-bit single-cycle multiplier, dual 40-bit accumulators, and a 40-stage barrel shifter. On-chip DMA enables data movement between peripherals and RAM without CPU intervention, critical for deterministic real-time control. According to Microchip, the dsPIC33F family is pin compatible with the PIC24HJ family and shares a high degree of compatibility with dsPIC30F devices, allowing seamless migration between PIC24F, dsPIC30F, and dsPIC33F platforms. This protects software investment and simplifies PCB reuse across product variants. Typical applications include precision motor control (BLDC, PMSM, FOC), digital power supplies and power factor correction, sensorless control systems, and general digital signal processing in industrial equipment. For design, note the supply range is 3.0V to 3.6V; decouple both VDD pins and AVDD with 0.1uF ceramics placed close to the pins, and follow the Microchip dsPIC33F family reference manual for oscillator and MCLR circuit design. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in same-family alternatives, and practical engineering notes in one place.

RFQ צור קשר

DSPIC33FJ64MC204-E/ML

DSPIC33FJ64MC204-E/ML - 16-bit DSC 40MIPS 64KB | Microchip

The Microchip Technology DSPIC33FJ64MC204-E/ML is a 16-bit Digital Signal Controller (DSC) delivering up to 40 MIPS from a 64 KB (64K x 8) Flash program memory, housed in a 44-pin QFN (8x8 mm) package with exposed pad. It operates from a 3.0 V to 3.6 V supply and integrates motor-control PWM and advanced analog peripherals for high-speed, repetitive computation and control tasks. A Digital Signal Controller combines a microcontroller (MCU) with the multiply-accumulate (MAC) DSP engine of a digital signal processor. In the power-management hierarchy, the dsPIC33F family sits within Microchip's 16-bit MC/DSC portfolio: DSC -> digital signal controller -> 16-bit MCU -> embedded processor. This hybrid architecture lets a single chip execute both general firmware (state machines, communication stacks) and compute-intensive loops such as field-oriented motor-control and digital power conversion. Key features include the 16-bit dsPIC33F core with DSP instruction extensions and dual 40-bit accumulators, 64 KB self-programming Flash, 8 KB SRAM, Direct Memory Access (DMA) with motor-control support, Motor Control PWM outputs, advanced 10-bit/12-bit analog-to-digital conversion, and up to 21 I/O ports. The -E suffix denotes the extended (-40C to +125C) operating temperature range; the /ML suffix denotes the RoHS, lead-free 44-QFN package. Architecturally, the dsPIC33F core is pin-compatible with the PIC24HJ family and shares a very high degree of compatibility with dsPIC30F devices, allowing seamless migration between PIC24F, dsPIC30F and dsPIC33F platforms. The deterministic interrupt latency and hardware MAC make it well suited to real-time closed-loop control at fixed sample rates. Typical applications include brushless DC and PMSM motor drives, switch-mode power supplies and digital power, automotive auxiliary systems, and industrial automation nodes requiring both control and signal processing. For design, budget the core regulator capacitor (VCAP/VDDCORE) exactly per the manufacturer datasheet and decouple all VDD/AVDD pins; 3.3 V supply tolerance is 3.0 V to 3.6 V. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר

DSPIC33FJ64MC204-I/ML

DSPIC33FJ64MC204-I/ML - 16-bit DSC 40MIPS 64KB QFN-44 | Microchip

The Microchip Technology DSPIC33FJ64MC204-I/ML is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance with 64 KB (64K x 8) Flash program memory, integrated DMA, and motor-control PWM peripherals, housed in a 44-pin QFN (8x8 mm) surface-mount package. A digital signal controller combines the compute power of a DSP with the peripheral set and ease of use of a microcontroller. In the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it executes high-speed, repetitive mathematical operations (PID loops, transforms, filtering) while also handling general I/O, communication, and control tasks in a single chip. Microchip's dsPIC33F family is pin compatible with the PIC24HJ family and shares a very high degree of compatibility with the dsPIC30F family, enabling seamless migration. Key features of the DSPIC33FJ64MC204-I/ML include the 16-bit dsPIC33F core running at up to 40 MIPS, 64 KB of self-programming Flash, on-chip DMA for data movement without CPU intervention, motor-control PWM and advanced analog peripherals, and 21 I/O ports. The supply voltage range is 3 V to 3.6 V, and the -I temperature grade covers -40C to +85C operation. Technically, the dsPIC33FJ64MC204 employs a modified Harvard 16-bit architecture with DSP engine support (barrel shifter, multiply-accumulate), boundary scan support, and multiple low-power modes. The DMA controller offloads peripheral data transfers, which is essential in motor-control and digital-power loops where deterministic interrupt latency matters. Flash self-programming supports field firmware updates. Typical applications include precision motor control (BLDC, PMSM, ACIM drives), digital power supplies (LLC, totem-pole PFC), sensor signal processing in industrial automation, and embedded control in consumer and automotive-adjacent systems. The motor-control PWM with complementary outputs and dead-time insertion makes this family a frequent choice for inverter designs. A key design consideration: the 3.0-3.6 V supply is not 5 V tolerant for most I/O, so level shifting is required when interfacing 5 V logic; also plan decoupling capacitors on all VDD/VSS pairs of the QFN-44 package. As of 2026-09-27, this page consolidates distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.

RFQ צור קשר

DSPIC33FJ64MC204-I/PT

DSPIC33FJ64MC204-I/PT - 16-bit 40MIPS DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33FJ64MC204-I/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance with 64 KB of Flash program memory and 8 KB of data RAM, housed in a 44-pin TQFP (10x10 mm) surface-mount package rated from -40C to +85C. A digital signal controller combines the computational throughput of a DSP engine with the peripherals and ease of use of a microcontroller, sitting in the component hierarchy between a general-purpose MCU (such as the PIC24 family) and a dedicated DSP. DSCs are optimized for control loops that also require high-speed repetitive math, such as field-oriented motor control and digital power conversion. Key features of this device include a modified Harvard 16-bit architecture executing at up to 40 MIPS, 8 channels of DMA for data movement without CPU overhead, 7 timers, 2 serial I/O ports (UART), and support for up to 3 external interrupts. Per Microchip, the dsPIC33F family is pin compatible with the PIC24HJ family and shares a very high degree of compatibility with dsPIC30F devices, enabling seamless migration. The dsPIC33FJ64MC204 belongs to the Motor Control (MC) subfamily, which integrates motor control PWM peripherals and advanced analog features tailored for precision motion, power factor correction, and switched-mode power supplies. The CMOS process keeps active power low at full 40 MIPS operation, supporting thermally constrained industrial enclosures. Typical applications include brushless DC and PMSM motor drives, digital power supplies and solar inverters, industrial automation nodes, and sensor signal processing where repetitive multiply-accumulate workloads dominate. According to Microchip product documentation, the device operates from a single 3.3 V supply. Design consideration: budget the 8 KB of RAM carefully - DSP filtering buffers and DMA descriptors consume it quickly, so use the DMA engine and X-Y addressing modes rather than software copies. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר

תת-קטגוריות

מוצרים (39,000+)

DSPIC33FJ64GS606-I/PT - 16-bit DSC, 40 MIPS, 64KB Flash | Microchip

DSPIC33FJ64GS606T-50I/PT - 16-bit 50MIPS DSC 64KB Flash | Microchip

DSPIC33FJ64GS606T-I/MR - 16-bit 40MIPS DSC 64KB | Microchip

DSPIC33FJ64GS606T-I/PT - 16-bit DSC 40MIPS 64KB Flash | Microchip

DSPIC33FJ64GS608-50I/PT - 16-bit 50MIPS DSC | Microchip

DSPIC33FJ64GS608-I/PT - 16-bit DSC 40MIPS 64KB Flash | Microchip

DSPIC33FJ64GS608T-50I/PT - 16-bit DSC 50MIPS 64KB | Microchip

DSPIC33FJ64GS610-50I/PT - 16-bit DSC 50MIPS 64KB Flash | Microchip

DSPIC33FJ64GS610-E/PT - 16-bit 40MIPS DSC, 64KB Flash | Microchip

DSPIC33FJ64GS610-I/P - 16-bit DSC 40MIPS 64KB Flash | Microchip

DSPIC33FJ64GS610-I/PF - 16-bit DSC 40 MIPS 64KB Flash | Microchip

DSPIC33FJ64GS610T-50I/PF - 16-bit 50MIPS DSC 64KB Flash | Microchip

DSPIC33FJ64GS610T-50I/PT - 16-bit 50MIPS DSC 64KB Flash | Microchip

DSPIC33FJ64GS610T-I/PF - 16-bit DSC 40MIPS 64KB | Microchip

DSPIC33FJ64GS610T-I/PT - 40MIPS 16-bit DSC for Digital Power | Microchip

DSPIC33FJ64MC202-E/MM - 16-bit DSC 40MIPS 64KB Flash QFN-28 | Microchip

DSPIC33FJ64MC202-E/SP - 16-bit DSC 64KB Flash 40MIPS | Microchip

DSPIC33FJ64MC202-I/MM - 16-bit DSC 40MIPS 64KB Flash QFN-28 | Microchip

DSPIC33FJ64MC202-I/SO - 16-bit DSC 40MIPS 64KB Flash | Microchip

DSPIC33FJ64MC202-I/SP - 16-bit DSC 40MIPS 64KB Flash | Microchip

DSPIC33FJ64MC202T-I/SO - 16-bit 40MIPS DSC, 64KB Flash | Microchip

DSPIC33FJ64MC204-E/ML - 16-bit DSC 40MIPS 64KB | Microchip

DSPIC33FJ64MC204-I/ML - 16-bit DSC 40MIPS 64KB QFN-44 | Microchip

DSPIC33FJ64MC204-I/PT - 16-bit 40MIPS DSC 64KB Flash | Microchip