מיקרו-בקרים

מוצרים (20,000+)

PIC16F15325T-I/SL - 8-bit MCU, 14KB Flash, 32MHz XLP | Microchip
PIC16F15325T-I/SL

PIC16F15325T-I/SL - 8-bit MCU, 14KB Flash, 32MHz XLP | Microchip

The Microchip Technology PIC16F15325T-I/SL is a 8-bit PIC microcontroller from the PIC16(L)F153XX family with 14KB Flash, 1KB RAM, and a 32MHz internal oscillator housed in a 14-pin SOIC (SL) package. It integrates the eXtreme Low-Power (XLP) technology, four Configurable Logic Cells (CLCs), Complementary Waveform Generator (CWG), two EUSART peripherals, and 12-bit ADC with computation. What is a Microcontroller (MCU)? A microcontroller is a single-chip computer containing a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and integrated peripherals such as timers, communication interfaces, and analog blocks. Within the taxonomy, this device belongs to: 8-bit MCU -> PIC16 family -> mid-range microcontroller -> embedded controller -> semiconductor. The 'F' suffix denotes Flash program memory; the '15325' is the family/specific device identifier within the PIC16F153xx lineup. Key features include a 32MHz maximum CPU clock (8MHz instruction rate with 4x PLL), 14KB Flash program memory (8K x 14 words), 1KB RAM, 256B EEPROM, 12-bit ADC with computation, 5-bit DAC, multiple PWMs, comparators, and CWG for advanced waveform generation. The XLP technology enables deep sleep currents below 50nA typical, making it ideal for battery-powered applications. The PIC16F15325 uses an enhanced mid-range 8-bit RISC core with a 14-bit instruction word, hardware multiplier, and C compiler-friendly architecture (XC8). Core Independent Peripherals (CIPs) like CLC, CWG, and NCO allow complex signal generation and processing without CPU intervention, freeing the core for low-power sleep and reducing firmware complexity. Typical applications include IoT sensor nodes, battery-powered remote controls, LED lighting controllers, motor control signal chains, low-power wireless sensor interfaces, and consumer appliance controls. The combination of CIPs and XLP suits always-on edge devices requiring both analog integration and minimal quiescent draw. Design consideration: leverage the CWG and CLC peripherals for hardware-based waveform generation to offload the CPU and enable lower average power. Place a 0.1uF decoupling capacitor adjacent to each VDD pin with a wide ground return for ADC noise immunity. Ensure the MCLR pull-up is properly configured for reliable reset in noisy environments. This page synthesizes distributor pricing, drop-in alternatives from the PIC16F153xx family, and practical design notes for low-power embedded applications not collected in the manufacturer datasheet alone.

RFQ צור קשר
PIC16F15344-E/GZ - 8-bit XLP MCU, 7KB Flash, 20-UQFN | Microchip
PIC16F15344-E/GZ

PIC16F15344-E/GZ - 8-bit XLP MCU, 7KB Flash, 20-UQFN | Microchip

The Microchip PIC16F15344-E/GZ is an 8-bit PIC microcontroller from the PIC16F153xx family that pairs an enhanced mid-range core with eXtreme Low-Power (XLP) technology, delivering 32 MHz CPU performance, 7 KB of self-read/write Flash program memory, 512 bytes of RAM, and Core Independent Peripherals (CIPs) in a compact 20-pin UQFN (4x4 mm) package. It also integrates Intelligent Analog peripherals, including a 10-bit ADC with computation and dual comparators, providing a versatile platform for general-purpose embedded designs. An 8-bit microcontroller (MCU) is a programmable integrated circuit built around an 8-bit data bus and a Harvard or modified-Harvard architecture. Within the broader hierarchy, an MCU sits inside the microcontrollers category, which itself is a subset of embedded processors and ultimately of digital integrated circuits. The PIC16F15344 belongs to Microchip's enhanced mid-range PIC16F core family, distinguished by 49 instructions and 16 stack levels, optimized for deterministic real-time control and ultra-low power consumption. Key features include a wide operating voltage range of 1.8 V to 5.5 V, ultra-low-power IDLE and DOZE modes, an on-chip 32 MHz internal oscillator, configurable logic cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and multiple communication peripherals such as EUSART, I2C, and SPI. The XLP architecture typically delivers nanoWatt sleep currents, supporting battery-powered applications that must operate for years on a single cell. The 20-UQFN (4x4 mm) package provides an extremely compact footprint suited for space-constrained designs, while the exposed pad aids thermal performance. Integrated peripheral pin select (PPS) simplifies board routing by allowing digital peripheral I/O to be remapped across most pins, reducing PCB layout complexity in mixed-signal designs. Typical applications include IoT sensor nodes, battery-powered wearables, home automation, low-power wireless HMI front ends, and consumer white goods. The combination of XLP nanoWatt technology, flexible peripherals, and a small footprint also suits medical monitoring accessories and industrial sensor hubs. When designing with this device, leverage IDLE/DOZE modes aggressively and configure the NCO + CLC for hardware-based timing to keep the CPU asleep for most of the duty cycle.

RFQ צור קשר
PIC16F15344-E/P - 8-bit 32MHz XLP MCU 7KB Flash 20-PDIP | Microchip
PIC16F15344-E/P

PIC16F15344-E/P - 8-bit 32MHz XLP MCU 7KB Flash 20-PDIP | Microchip

The Microchip Technology PIC16F15344-E/P is an 8-bit PIC microcontroller built on the enhanced mid-range architecture with 49 instructions and 16 stack levels, offering 7KB (4K x 14) of self read/write Flash program memory in a 20-pin PDIP through-hole package. It integrates 32 MHz operation, 512 bytes SRAM, 256 bytes EEPROM, and eXtreme Low Power (XLP) IDLE and DOZE modes for battery-powered applications across the 2V to 5.5V operating range. An 8-bit PIC microcontroller (MCU) is a single-chip computer that combines an 8-bit CPU core, Flash program memory, RAM, EEPROM, and a rich set of analog and digital peripherals into a compact IC optimized for embedded control. It sits within the broader hierarchy: microcontroller -> embedded processor -> semiconductor device. Microchip's PIC16F family is widely adopted in consumer, industrial, and IoT products because the architecture is deterministic, the toolchain (MPLAB X IDE, XC8 compiler, MPLAB Code Configurator) is free, and CIPs (Core Independent Peripherals) offload tasks from the CPU. Key features include a 10-bit ADC with computation (ADC2), two 8-bit DACs, two high-speed comparators, an 8-bit timer (Timer2), a 16-bit timer (Timer1), and four Configurable Logic Cells (CLCs) that allow glue-logic functions to be implemented in hardware without CPU intervention. Core Independent Peripherals such as the CWG (Complementary Waveform Generator), NCO (Numerically Controlled Oscillator), and four 10-bit PWMs enable motor, lighting, and signal-generation functions while the CPU sleeps. Typical applications include IoT sensor nodes running on coin-cell batteries, low-power wireless remote controls, HVAC thermostat front panels, smart lighting ballasts, and small appliance user interfaces. The dual EUSART, SPI, and I2C interfaces support bridges to sensors, displays, and external radios; the 32 MHz internal oscillator eliminates an external resonator on most designs. When designing with this device, prefer the internal 32 MHz HFINTOSC to minimize BOM cost and reserve the two GPIO-capable pins for wake sources. Always enable the watchdog timer in software if the application is safety-relevant, since the XLP sleep currents are below 50 nA in Retention mode. This page synthesizes distributor pricing, drop-in alternatives, parametric comparisons, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PIC16F15344-E/SO - 8-Bit 32MHz 7KB Flash MCU | Microchip
PIC16F15344-E/SO

PIC16F15344-E/SO - 8-Bit 32MHz 7KB Flash MCU | Microchip

The Microchip Technology PIC16F15344-E/SO is an 8-bit PIC microcontroller from the PIC16F153XX family featuring the enhanced mid-range core with 49 instructions and 16 stack levels, 32 MHz operation, 7 KB (4K x 14) self-read/write Flash program memory, 512 B RAM, and a 20-pin SOIC package. It is part of Microchip's eXtreme Low-Power (XLP) family, integrating IDLE and DOZE low-power modes for energy-constrained applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, and peripherals such as timers, ADC, communication interfaces, and I/O. The 8-bit PIC MCU family sits in the broader hierarchy of embedded microcontrollers -> microcontrollers -> integrated circuits -> semiconductors, serving cost-sensitive and power-constrained designs where 32-bit processing is unnecessary. Key features include 7 KB Flash, 512 B SRAM, 4 PWMs, a comparator, a 5-bit DAC, an ADC, 4 Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), 2 EUSART, and SPI/I2C communication. Core Independent Peripherals (CIPs) operate without CPU intervention, allowing deterministic real-time response and reducing firmware complexity. The PIC16F15344-E/SO operates from 2.3V to 5.5V (industrial temperature range -40C to +125C) and uses Microchip's XLP architecture with nanoWatt XLP sleep currents. The 20-pin SOIC package supports through-hole-friendly hand-soldering and reflow profiles compatible with JEDEC J-STD-020. Typical applications include low-power IoT sensor nodes, battery-powered consumer devices, LED lighting controllers, simple motor control, and home appliances. The combination of EUSART, SPI, and I2C plus PWM and CWG suits brushed DC and small BLDC fan control. When designing with this device, ensure decoupling capacitors (100 nF plus 10 uF bulk) are placed within 5 mm of VDD, leave the ICSPCLK/ICSPDAT pins accessible for in-circuit programming, and use Microchip's MPLAB X IDE with the XC8 compiler for code development.

RFQ צור קשר
PIC16F15344-E/SS - 8-bit MCU, 7KB Flash, 32MHz, 20-SSOP | Microchip
PIC16F15344-E/SS

PIC16F15344-E/SS - 8-bit MCU, 7KB Flash, 32MHz, 20-SSOP | Microchip

The Microchip Technology PIC16F15344-E/SS is an 8-bit PIC microcontroller from the PIC16F153xx family, featuring 7KB (4K x 14 words) of self-read/write Flash program memory, 512 bytes of SRAM, and 32 MHz internal oscillator speed, housed in a 20-pin SSOP (Shrink Small Outline Package). The -E suffix denotes the Extended industrial temperature grade of -40C to +125C, while the /SS suffix denotes the 20-pin SSOP package. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, SRAM, EEPROM), and programmable I/O peripherals. The PIC16F15344 belongs to Microchip's enhanced mid-range 8-bit core family with 49 instructions and 16 stack levels, executing most instructions in one instruction cycle. Within the broader taxonomy, it is an 8-bit MCU -> microcontroller -> embedded processor -> semiconductor device, designed for general-purpose and low-power embedded control. Key features of the PIC16F15344-E/SS include four 10-bit PWM outputs, a 5-bit DAC, a comparator, a 10-bit ADC with computation (ADCC), four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and dual EUSART with SPI/I2C support. The Intelligent Analog peripherals and Core Independent Peripherals (CIPs) enable complex control tasks to run autonomously without CPU intervention, reducing firmware complexity and power consumption. The device employs Microchip's eXtreme Low Power (XLP) technology with IDLE and DOZE low-power modes, making it well suited for battery-powered applications. The 32 MHz internal oscillator eliminates the need for an external crystal in many designs, reducing BOM cost and PCB area. The 20-SSOP package offers a compact footprint for space-constrained designs while supporting full peripheral functionality. Typical applications include IoT sensor nodes, home automation controllers, low-power wireless devices, industrial control modules, LED lighting controllers, and battery-powered consumer electronics. The combination of 4 CLCs and a CWG makes the PIC16F15344 particularly effective for driving power-conversion circuits and motor-control signal generation. When designing with this MCU, ensure the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible for in-circuit programming, and provide adequate decoupling (100nF plus 10uF bulk) close to the VDD pin. The 20-SSOP package has a thermal pad underneath that should be soldered to the ground plane for mechanical stability and thermal performance.

RFQ צור קשר
PIC16F15344-I/GZ - 8-bit MCU, 7KB Flash, 32MHz, 20-UQFN | Microchip
PIC16F15344-I/GZ

PIC16F15344-I/GZ - 8-bit MCU, 7KB Flash, 32MHz, 20-UQFN | Microchip

The Microchip Technology PIC16F15344-I/GZ is an 8-bit PIC microcontroller from the PIC16(L)F153xx family featuring 7KB (4K x 14) Flash program memory, 512 bytes of RAM, and a maximum CPU clock of 32 MHz, housed in a compact 20-pin UQFN (4x4 mm) package. It combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low Power (XLP) technology with IDLE and DOZE low-power modes, making it suitable for a wide range of low-power and general-purpose embedded designs. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory (Flash), data memory (RAM), and a rich set of peripheral interfaces onto a single silicon die. The "PIC" family from Microchip uses a Harvard-architecture RISC core that executes one instruction per clock cycle (excluding branches), offering deterministic behavior prized in real-time control. PIC16F153xx devices sit in the "Enhanced Mid-Range" tier with 49 instructions and 16 stack levels, providing a balance of code efficiency, peripheral integration, and cost-effectiveness for consumer, industrial, and IoT applications. Key features of the PIC16F15344-I/GZ include 7KB self-read/write Flash, 512 bytes RAM, a 10-bit ADC with computation (ADC2), a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), four 10-bit PWMs, and 2 EUSART plus SPI/I2C communication interfaces. The device also includes peripheral pin select (PPS) for flexible routing and multiple timer modules. The PIC16F15344 uses Microchip's enhanced mid-range core with 49 instructions and 16 stack levels. The XLP architecture enables deep sleep currents in the nanoamp range with retention, making the device attractive for battery-powered sensor nodes where quiescent current dominates battery life. Hardware CIPs such as the CWG, configurable logic cells (CLC), and signal measurement timer (SMT) offload timing-critical tasks from the CPU, reducing code complexity and power consumption. Typical applications include IoT sensor nodes, battery-powered wearables, home automation controllers, low-power wireless peripherals, consumer white goods, industrial sensor interfaces, and small motor-control subsystems where on-chip PWMs and comparators simplify the BOM. Its tiny 4x4 mm UQFN footprint suits space-constrained designs. When designing with the PIC16F15344-I/GZ, ensure the UQFN-20 PCB footprint includes a sufficient central exposed pad for thermal dissipation and solder joint reliability. Decouple VDD with a 100 nF ceramic capacitor placed close to the supply pin, and follow Microchip AN1248 for low-power PCB layout to minimize leakage paths in battery applications. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for part selection, replacement, and BOM risk reduction.

RFQ צור קשר
PIC16F15344-I/MLVAO - 8-bit MCU, 7KB Flash, 32MHz, 20-QFN | Microchip
PIC16F15344-I/MLVAO

PIC16F15344-I/MLVAO - 8-bit MCU, 7KB Flash, 32MHz, 20-QFN | Microchip

The Microchip PIC16F15344-I/MLVAO is an 8-bit PIC microcontroller built on the enhanced mid-range core, delivering 32MHz CPU performance with 7KB (4K x 14) of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM in a 20-pin QFN (4x4 mm) package with exposed pad. The device integrates intelligent analog peripherals, Core Independent Peripherals (CIPs), and communication interfaces including 2x EUSART, SPI, and I2C, making it suitable for a wide range of general-purpose and low-power embedded designs. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path that executes instructions from on-chip Flash memory and integrates CPU, RAM, EEPROM, timers, ADCs, and communication peripherals. Within the broader taxonomy, the PIC16F15344 belongs to the PIC microcontroller family -> 8-bit MCU -> microcontrollers -> embedded ICs -> semiconductor. The eXtreme Low-Power (XLP) technology at the core of this device targets battery-powered applications by reducing active and sleep currents below competing architectures. Key features include a 10-bit ADC with computation (ADC2), a 5-bit DAC, two comparators, four 10-bit PWMs, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), two EUSART modules, and SPI/I2C interfaces. The CIPs allow hardware-based peripheral interaction without CPU intervention, offloading timing-critical tasks. The instruction set is highly orthogonal with 49 single-word instructions, and the device operates across 2.3V to 5.5V with active current under 2 mA at 32MHz. Architecturally, the PIC16F15344 uses a Harvard architecture with separate program and data buses, enabling single-cycle instruction execution except for branches. The interrupt controller supports both legacy and new peripheral interrupt sources with vectored prioritization. The Flash self-programming capability via ICSP and the configurable oscillator block add design flexibility for bootloader and clock-scaling use cases. Typical applications include automotive body and sensor modules (AEC-Q100 qualified via the MLVAO suffix), IoT sensor nodes, low-power wireless companion MCUs, LED lighting controllers, home appliance user interfaces, and small motor control. The combination of CWG, PWM, and ADC2 enables single-chip BLDC and LED driver designs. When designing with this part, observe the QFN PCB layout rules: thermal pad must be soldered to a continuous ground plane with multiple vias, and decoupling capacitors placed as close to VDD/VSS pairs as possible. The MLVAO suffix indicates the automotive-qualified (-40C to +125C) version in the 20-QFN (4x4) package.

RFQ צור קשר
PIC16F15344-I/P - 8-Bit 32MHz MCU, 7KB Flash, 20-PDIP | Microchip
PIC16F15344-I/P

PIC16F15344-I/P - 8-Bit 32MHz MCU, 7KB Flash, 20-PDIP | Microchip

The Microchip Technology PIC16F15344-I/P is an 8-bit PIC microcontroller built on the enhanced mid-range core with 49 instructions and 16 stack levels, operating at up to 32MHz, housed in a 20-pin PDIP (DIP-20) through-hole package. The device integrates 7.168 KB of self read/write Flash program memory, 512 bytes of data SRAM, and 18 bytes of data EEPROM, providing flexible in-application re-programmability for field-upgradable designs. An 8-bit microcontroller (MCU) is a single-chip computer that uses an 8-bit data bus and is optimized for low-power, real-time control of embedded systems. The PIC16F15344 belongs to the PIC16(L)F153xx family of enhanced mid-range MCUs, sitting within the broader hierarchy: microcontroller -> embedded processor -> semiconductor. It combines eXtreme Low-Power (XLP) technology with Core Independent Peripherals (CIPs) to offload tasks from the CPU, reducing active time and average power consumption. Key features include Intelligent Analog peripherals (10-bit ADC with computation, 5-bit DAC, comparators), four 10-bit PWMs, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and two Enhanced USART (EUSART) modules plus SPI/I2C. The device operates from 2.3V to 5.5V (industrial grade), supports IDLE and DOZE low-power modes, and includes a peripheral pin select (PPS) block for flexible signal routing. The enhanced mid-range core delivers up to 16 MIPS at 32MHz while consuming only nanoamp sleep currents in XLP mode. The self-read/write-capable Flash enables field firmware updates without external programmers, and the integrated 18-byte EEPROM provides non-volatile data storage for user settings or calibration constants. Typical applications include low-power IoT sensor nodes, battery-powered home automation devices, automotive body and interior electronics, industrial sensor interfaces, and consumer white goods requiring intelligent analog sensing. The DIP-20 package simplifies prototyping on breadboards and through-hole evaluation boards. When designing with this device, route analog and digital grounds separately to a single point near the MCU's GND pin, and place the 0.1uF VDD decoupling capacitor within 5mm of the package. For noise-sensitive applications, prefer the QFN package variant for better thermal and electrical performance. This page synthesizes real-time distributor pricing, drop-in alternatives within the same PIC16F153xx family, and practical design notes not found in the manufacturer datasheet, helping engineers shorten sourcing and design cycles.

RFQ צור קשר
PIC16F15344-I/SO - 8-Bit 32MHz XLP MCU 7KB Flash 20-SOIC | Microchip
PIC16F15344-I/SO

PIC16F15344-I/SO - 8-Bit 32MHz XLP MCU 7KB Flash 20-SOIC | Microchip

The Microchip Technology PIC16F15344-I/SO is an 8-bit RISC microcontroller from the PIC16 (L)F153xx family, featuring an Enhanced Mid-Range Core with 49 instructions and 16 stack levels, delivering up to 32MHz CPU performance in a 20-pin SOIC (SO) package. The device integrates 7KB (4K x 14) of self read/write Flash program memory, 512 bytes of SRAM, and an on-board 32KB data EEPROM emulation area, targeting general-purpose and low-power embedded applications. Operating voltage spans 2.3V to 5.5V across the -40C to +85C industrial temperature range, with a low-power variant (PIC16LF15344) extending down to 1.8V. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for deterministic real-time control in cost- and power-sensitive designs. Within the broader semiconductor hierarchy, 8-bit MCUs belong to the microcontroller category, which itself sits under microcontrollers and processors, then integrated circuits, and ultimately semiconductors. The PIC16F153xx line combines this MCU foundation with on-chip intelligent analog and Core Independent Peripherals (CIPs), letting designers sense, drive, and communicate without burdening the CPU. Key features include four 10-bit PWMs with complementary waveform generation, a 5-bit DAC, one comparator, a 10-bit ADC with computation, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two EUSART peripherals, and SPI/I2C masters. eXtreme Low-Power (XLP) technology with IDLE and DOZE modes, plus Peripheral Module Disable, enables deep current savings for battery-powered designs. The 20-pin SOIC package provides a 7.50mm body width for through-hole-style footprints and supports -40C to +85C industrial operation. Typical applications include IoT sensor nodes, consumer electronics, battery-powered remote controls, LED lighting controllers, and small home appliances. Designers select this part when they need rich analog integration, multiple serial interfaces, and ultra-low standby current in a compact 20-pin SOIC footprint. The PIC16F15344 differs from the lower-pin PIC16F15324 by exposing 4 additional I/O, while sharing the same peripheral set for software portability. When designing with this MCU, ensure the MCLR pull-up is enabled in configuration bits and that the on-chip 16MHz HFINTOSC is calibrated for UART timing over the full temperature range. Use Peripheral Module Disable to gate unused peripherals during sleep to maximize XLP current savings. This page synthesizes distributor stock data, drop-in package-compatible alternatives, and practical design notes for the PIC16F15344-I/SO not found in any single manufacturer datasheet.

RFQ צור קשר
PIC16F15344-I/SS - 8-bit 32MHz XLP MCU 7KB Flash | Microchip
PIC16F15344-I/SS

PIC16F15344-I/SS - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC16F15344-I/SS is an 8-bit PIC microcontroller from the PIC16F153xx family, featuring a 32MHz internal oscillator, 7KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM, housed in a 20-pin SSOP (SS) package. It runs from 2.3V to 5.5V and integrates four Configurable Logic Cells (CLCs), four 10-bit PWM channels, a 10-bit ADC with computation, a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), and two EUSART plus SPI/I2C peripherals, all on a single enhanced mid-range core with 49 instructions and 16 stack levels. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals (timers, communication blocks, ADCs) into one package. The PIC16 architecture is an 8-bit RISC-style core designed by Microchip that uses a 14-bit instruction word and Harvard bus architecture, sitting within the broader 8-bit MCU category and competing against AVR and 8051 families in low-power and cost-sensitive embedded designs. Key features of this part include eXtreme Low-Power (XLP) technology with IDLE and DOZE modes, peripheral pin select for flexible signal routing, zero-crossing detection on comparators, and on-chip debugging via the ICD interface. The four CLCs allow state-machine-style logic to be implemented in hardware without external glue, reducing BOM cost and CPU overhead in sensor and lighting control designs. The 32MHz core delivers up to 8 MIPS, while the 10-bit ADC with computation (ADC2) performs automatic averaging, accumulation, and threshold comparison in hardware, offloading the CPU. The CWG block generates complementary PWM with programmable dead-band control, ideal for half-bridge and full-bridge FET drivers in motor control and Class-D audio stages. Typical applications include battery-powered sensor nodes, IoT edge devices, LED lighting controllers, low-cost motor control (fans, BLDC pumps), home appliances (white goods user interfaces), and human-machine interface panels with capacitive touch driven by CLCs. The 20-pin SSOP footprint is well suited to compact PCBs where 8-pin or 14-pin parts lack sufficient I/O. When designing with this MCU, mind the 2.3V minimum Vdd for the F (Flash) variant and reserve one I/O for the ICSPDAT/ICSPCLK debug pair to keep MPLAB X ICD in-circuit programming usable in production boards. Adding a 100nF decoupling cap within 3 mm of each Vdd pin and a 10k pull-up on MCLR is mandatory for reliable reset behavior. This page synthesizes distributor pricing, drop-in alternatives within the PIC16F153xx family, and practical design notes not found in the manufacturer datasheet alone, organized for fast lookup by procurement and embedded firmware engineers.

RFQ צור קשר
PIC16F15344T-I/SS - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip
PIC16F15344T-I/SS

PIC16F15344T-I/SS - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15344T-I/SS is an 8-bit PIC microcontroller built on the Enhanced Mid-Range core with 49 instructions and 16 stack levels, operating at up to 32MHz, integrating 7KB (4K x 14 words) of self-read/write Flash program memory, 512 bytes of SRAM, and housed in a 20-pin SSOP package. The device features a 10-bit ADC with up to 17 channels, a 5-bit DAC with 1 channel, four 10-bit PWMs, two comparators, two EUSART modules, two MSSP (SPI/I2C) modules, four Configurable Logic Cells (CLC), and a Complementary Waveform Generator (CWG), forming the Core Independent Peripherals (CIPs) foundation of the PIC16(L)F153xx family. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, memory (Flash for program, SRAM for data, EEPROM for non-volatile storage), and peripherals on a single die. Within the semiconductor hierarchy, 8-bit MCUs belong to the microcontroller family, which sits under the broader category of embedded processors and digital ICs. Microchip's PIC16F family uses a Harvard RISC architecture optimised for deterministic real-time control, and the F153xx sub-family layers Intelligent Analog (ADC/DAC/comparators) and Core Independent Peripherals on top of eXtreme Low-Power (XLP) technology that includes IDLE and DOZE low-power modes for battery-driven applications. Key features of the PIC16F15344T-I/SS include eXtreme Low-Power operation with typical deep-sleep currents in the nanoamp range, peripheral module disable for granular power savings, and 4x CLC blocks that let designers replace discrete glue logic with on-chip configurable logic. The CIPs let ADC triggering, PWM generation, and communication handshakes run without CPU intervention, freeing the core for higher-level application code. Architecturally, the F153xx uses a 14-bit instruction word with a 16-level hardware stack, supports self-read/write of program memory, and provides multiple clock sources (HFINTOSC, LFINTOSC, external crystal, and PLL) with Fail-Safe Clock Monitor for robust operation. The combination of intelligent analog, CIPs, and XLP positions the part for sensor nodes, IoT edge devices, and consumer appliances where deterministic real-time response, low quiescent current, and rich on-chip peripherals reduce BOM cost. Typical applications include low-power IoT sensor nodes, battery-powered consumer devices, home appliance control boards, LED lighting drivers, and small motor-control subsystems. Its wide operating voltage and rich peripheral mix also suit industrial sensor interfaces. When designing with this device, prioritise power supply decoupling close to VDD/AVDD/VSS pairs, reserve the ICSP pins for in-circuit programming access, and use the peripheral module disable bits to minimise sleep current in always-on designs. This page synthesises distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet, supporting engineers during component selection and BOM validation.

RFQ צור קשר
PIC16F15345-E/GZ - 8-Bit MCU, 14KB Flash, 32MHz, UQFN-20 | Microchip
PIC16F15345-E/GZ

PIC16F15345-E/GZ - 8-Bit MCU, 14KB Flash, 32MHz, UQFN-20 | Microchip

The Microchip PIC16F15345-E/GZ is an 8-bit PIC microcontroller in the PIC16(L)F153xx family, featuring a 32MHz internal core, 14KB Flash program memory, 1KB RAM, and a 20-UQFN (4x4) package. It integrates Intelligent Analog peripherals, Core Independent Peripherals (CIPs), communication interfaces, and eXtreme Low-Power (XLP) technology, targeting low-power and general-purpose embedded applications. What is a PIC16 8-bit microcontroller? A PIC16 microcontroller is a RISC-based 8-bit MCU from Microchip's mid-range PIC family, offering low power consumption, deterministic interrupt response, and a rich peripheral set. Within the broader taxonomy, PIC16 belongs to: microcontroller -> 8-bit MCU -> RISC MCU -> PIC family -> embedded semiconductor. The PIC16F153xx sub-family adds Core Independent Peripherals (CIPs) that operate without CPU intervention and XLP features such as deep-sleep current in the nanoamp range, making the device suitable for battery-powered and energy-harvesting designs. Key features include 4 PWMs, a hardware comparator, a 5/8-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), 2 EUSART, and SPI/I2C interfaces. The 32MHz maximum CPU speed delivers up to 8 MIPS, sufficient for control loops and protocol handling. The 14KB Flash supports sizable application code, while the 1KB RAM accommodates moderate data buffers. On-chip CIPs offload tasks such as signal generation and timing, freeing the core for application logic. Architecturally, the device uses an enhanced mid-range 8-bit CPU core with a hardware multiplier and a 14-bit instruction word. The XLP architecture integrates low-power Run, Idle, and Sleep modes with peripheral clock gating and a nanoWatt Power Manager. Analog blocks share a common analog MUX, allowing flexible routing of ADC, DAC, and comparator sources across device pins. Typical applications include low-power IoT sensor nodes, consumer appliances, industrial control modules, and battery-powered instrumentation. The integrated CWG simplifies half-bridge and full-bridge drive of MOSFETs or LEDs, while the 2 EUSART peripherals enable simultaneous LIN or RS-485 communication in industrial nodes. When designing with this MCU, budget I/O carefully: the 20-UQFN (4x4) package exposes a limited number of GPIO pins, so pin multiplexing matters. Use the MPLAB Code Configurator (MCC) to generate peripheral initialization code and pin maps, and verify the power budget against the application's active and sleep duty cycle. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PIC16F15345-E/GZVAO - 8-bit 32MHz 14KB Flash MCU | Microchip
PIC16F15345-E/GZVAO

PIC16F15345-E/GZVAO - 8-bit 32MHz 14KB Flash MCU | Microchip

The Microchip Technology PIC16F15345-E/GZVAO is an automotive-grade (AEC-Q100) 8-bit PIC16 microcontroller running at up to 32 MHz, integrating 14 KB Flash, 1 KB SRAM, 256 bytes of EEPROM, and 18 I/O pins into a 20-pin UQFN (4x4 mm) package with exposed pad. It belongs to the PIC16(L)F153xx family of cost-effective microcontrollers that combine Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for low-power and general-purpose embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on one die. PIC16F-series MCUs use Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and RISC architecture. They typically sit below 16-bit PIC24/dsPIC and 32-bit PIC32MX parts in Microchip's portfolio, but above legacy 14-bit PIC16 baseline cores. They are widely used where low cost, deterministic interrupt response, and ultra-low sleep current are more important than raw compute throughput. Key differentiating features of the PIC16F15345 include four 10-bit PWM channels, a 10-bit ADC, two 5-bit DACs, comparators, a Complementary Waveform Generator (CWG), two EUSART peripherals plus SPI/I2C, and the eXtreme Low-Power (XLP) sleep mode that draws nanoamp-range currents. The 20-UQFN (GZ) package with exposed thermal pad reduces PCB footprint for space-constrained designs. Architecturally, the device uses Microchip's enhanced mid-range core with a hardware multiplier, 49 instruction set, and vectored interrupts. The CIPs (CLC, NCO, CWG, DSM, Configurable Logic Cell, Numerically Controlled Oscillator) allow hardware-state-machine functions to offload the CPU, enabling deterministic low-power response without firmware polling. Typical applications include automotive body and sensor node ECUs, IoT edge sensor nodes, industrial controls and instrumentation, low-power consumer appliances, LED lighting control, and small motor/solenoid drivers where CIPs handle timing in hardware. The wide 2.3V-5.5V operating range and nanoWatt XLP sleep modes also suit battery-powered designs such as remote controls and wearable health patches. When designing with the GZVAO suffix, note that AEC-Q100 qualification, the -E extended temperature grade (-40C to +125C), and the UQFN exposed pad require careful PCB thermal land and reflow profile matching. The VAO suffix indicates automotive-grade packaging and traceability per Microchip's part-numbering convention.

RFQ צור קשר
PIC16F15345-E/P - 14KB Flash 8-bit MCU, 32MHz, 20-PDIP | Microchip
PIC16F15345-E/P

PIC16F15345-E/P - 14KB Flash 8-bit MCU, 32MHz, 20-PDIP | Microchip

The Microchip Technology PIC16F15345-E/P is an 8-bit PIC microcontroller from the PIC16(L)F153xx family, featuring 14KB of Flash program memory, 1KB of RAM, and a 32MHz internal CPU speed, housed in a 20-pin PDIP (P) through-hole package. This Extended (E) temperature grade device operates across -40C to +125C and integrates 17 channels of 10-bit ADC plus a 5-bit DAC for mixed-signal designs. An 8-bit microcontroller (MCU) is a compact, self-contained computing device built around an 8-bit data path, typically used for real-time control, signal conditioning, and low-power embedded applications. MCUs sit at the lowest tier of the embedded computing hierarchy: they combine CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals (ADC, timers, communication ports) on a single die. The PIC16F family from Microchip uses a Harvard RISC architecture optimized for deterministic, low-latency interrupt handling. Key features of the PIC16F15345-E/P include Core Independent Peripherals (CIPs) such as 4 Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and 4 PWMs, plus 2 EUSART, SPI and I2C communication interfaces. The device also integrates eXtreme Low-Power (XLP) technology for battery-friendly designs, with deep-sleep currents in the nanoampere range. Combined with intelligent analog peripherals, this part targets low-power sensor nodes and human-machine interface (HMI) subsystems. The PIC16F15345-E/P architecture leverages a 14-bit instruction word RISC core with single-cycle execution for most instructions. The device includes 1024 bytes of RAM, an internal oscillator up to 32MHz, and supports in-circuit serial programming (ICSP) and debugging. The 5-bit DAC operates in conjunction with the 10-bit ADC to enable closed-loop analog control without external components. Typical applications include industrial sensor interfaces, consumer electronics HMI control, battery-powered IoT edge nodes, automotive body and accessory subsystems, and low-cost motor control. The wide operating temperature range and AEC-Q100-grade options within the family make the device attractive for both consumer and automotive environments. When designing with the PIC16F15345-E/P, allocate sufficient PCB real estate around the 20-PDIP footprint to allow for through-hole rework. Use decoupling capacitors of 100nF close to each VDD pin and follow Microchip's AN1095 PCB layout guidelines to minimize EMI and ensure oscillator stability. Choose the appropriate ICSP programming header to support in-field firmware updates. This page synthesizes distributor pricing, drop-in alternatives, application notes, and practical design guidance for the PIC16F15345-E/P that are not found on a single manufacturer or distributor page.

RFQ צור קשר
PIC16F15345-E/SS - 8-bit MCU, 14KB Flash, 32MHz, 20-SSOP | Microchip
PIC16F15345-E/SS

PIC16F15345-E/SS - 8-bit MCU, 14KB Flash, 32MHz, 20-SSOP | Microchip

The Microchip Technology PIC16F15345-E/SS is an 8-bit PIC16 microcontroller built on an enhanced mid-range core running at up to 32 MHz, integrating 14 KB (8K x 14) of self-programmable Flash program memory, 1 KB of SRAM and 256 bytes of EEPROM in a 20-pin SSOP package. It is part of the PIC16(L)F153xx cost-effective family that combines Intelligent Analog, Core Independent Peripherals (CIPs) and eXtreme Low-Power (XLP) technology for battery-aware and low-power designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a set of on-chip peripherals such as timers, ADC, communication interfaces and I/O ports. The PIC16 family sits in the taxonomy of: microcontroller -> 8-bit MCU -> PIC16 enhanced mid-range -> power-conscious embedded controller. It is the device class of choice for cost-sensitive, deterministic real-time control in consumer, industrial and IoT products where an ARM Cortex-M0+ would be over-specified. Key features of the PIC16F15345-E/SS include a 10-bit ADC with computation (ADC2), a 5-bit and 8-bit DAC, two comparators, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), four 10-bit PWMs, plus 2x EUSART, SPI and I2C (MSSP) for serial connectivity. The device also offers a Peripheral Pin Select (PPS) block, 1.8V-5.5V wide VDD operation and eXtreme Low-Power sleep currents in the nanoamp range, making it suited to energy-harvesting and battery-backed applications. Architecturally, the part uses a 14-bit instruction word enhanced mid-range core with hardware multiplier, hardware stack and 49 instruction set. The CIPs offload timing-critical logic to silicon (CLC, CWG, NCO), allowing software to remain idle for extended sleep periods - this is the source of its sub-uA sleep numbers claimed by Microchip XLP. Typical applications include low-power IoT sensor nodes, battery-powered home automation peripherals, LED lighting controllers, small appliance user-interface boards, brushed DC motor / fan control, and industrial sensor transmitters. The 20-SSOP footprint is also friendly to hand-rework prototypes and low-volume builds. When designing in this MCU, plan the PPS mapping early because peripheral-to-pin routing is software-configurable, and budget decoupling capacitance (100 nF + 1-10 uF bulk) close to VDD/AVDD pins to keep ADC2 readings quiet in noisy switcher environments.

RFQ צור קשר
PIC16F15345-I/GZ - 32MHz 8-bit MCU, 14KB Flash, 20-UQFN | Microchip
PIC16F15345-I/GZ

PIC16F15345-I/GZ - 32MHz 8-bit MCU, 14KB Flash, 20-UQFN | Microchip

The Microchip Technology PIC16F15345-I/GZ is an 8-bit PIC microcontroller operating at up to 32 MHz (approximately 8 MIPS), featuring 14 KB of Flash program memory and 1 KB of RAM, housed in a 20-pin UQFN (4x4 mm) package with exposed pad. The device integrates 4 PWMs, comparators, a DAC, ADC, Complementary Waveform Generator (CWG), two EUSART, and SPI/I2C peripherals. What is a PIC16 microcontroller? The PIC16 is a family of 8-bit microcontrollers from Microchip Technology built on a RISC Harvard architecture. PIC microcontrollers sit within the broader taxonomy of microcontroller (MCU) -> embedded controller -> semiconductor IC, and the PIC16 family specifically targets cost-sensitive, low-power, and peripheral-rich applications requiring deterministic real-time performance. The 'F' prefix denotes Flash program memory, and the XLP (eXtreme Low Power) designation signals sub-uA sleep currents suitable for battery-powered designs. Key features include eXtreme Low-Power (XLP) technology with sleep currents as low as ~30 nA typical, Core Independent Peripherals (CIPs) such as the CWG and configurable logic cells that offload tasks from the CPU, and Intelligent Analog peripherals including a 10-bit ADC with computation, two comparators, and a 5-bit DAC. The 32 MHz internal oscillator eliminates the need for an external resonator in many designs. Technical depth: the PIC16F15345 uses a 14-bit instruction word and supports up to 49 instructions with hardware multiply. The device operates from 2.5V to 5.5V and is offered in industrial (-40C to +85C, I-suffix) and extended (-40C to +125C, E-suffix) temperature grades. Memory includes 14 KB Flash, 1 KB SRAM, and 256 bytes of EEPROM, with internal self-programmability for bootloader-style firmware updates. Typical applications include IoT sensor nodes, LED lighting controllers, battery-powered consumer devices, low-end motor and fan control, and human-interface nodes (HMI buttons/knobs) where the CWG simplifies drive waveforms. The wide operating voltage and low sleep current make it well-suited for energy-harvesting or always-on edge devices. Design consideration: when migrating from larger PIC16 packages to this 20-UQFN, ensure the PCB land pattern matches the 4x4 mm UQFN footprint and that the exposed thermal pad is soldered to a continuous ground pour for thermal dissipation. Decoupling: place a 100 nF ceramic capacitor within 3 mm of each VDD pin and a bulk capacitor (1-10 uF) on the main supply rail. This page synthesizes distributor pricing, drop-in alternatives in the same 20-UQFN footprint, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PIC16F15345-I/SO - 8-bit MCU, 14KB Flash, 32MHz | Microchip
PIC16F15345-I/SO

PIC16F15345-I/SO - 8-bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15345-I/SO is an 8-bit PIC microcontroller from the PIC16(L)F153xx family with 14KB (8K x 14) self-programmable Flash, 1KB SRAM, 256 bytes of EEPROM, 32MHz CPU speed, and a 20-pin SOIC (300mils) package. It integrates XLP (eXtreme Low-Power) technology, Intelligent Analog, Core Independent Peripherals (CIPs), and a rich peripheral set including four 16-bit PWMs, a comparator, a 5-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), two EUSART, and SPI/I2C. An 8-bit microcontroller (MCU) is a single-cite embedded processor combining a RISC CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and configurable peripherals. Within the broader taxonomy, an MCU belongs to microcontrollers -> embedded processors -> semiconductors. The PIC16F153xx family sits in the mid-range of Microchip's 8-bit portfolio, above baseline PIC10/12/14 and below PIC18/dsPIC families, balancing cost and peripheral richness. Key differentiating features include sleep current below 50 nA typical for XLP battery applications, 18 I/O pins with interrupt-on-change capability, internal 32MHz HFINTOSC with ±1% accuracy, and CIPs that operate without CPU intervention. Core Independent Peripherals such as the CLC, CWG, and NCO enable deterministic real-time response, freeing the core for application logic and reducing firmware complexity. Architecturally, the PIC16F15345 uses a modified Harvard RISC core with 49 instructions, a 16-level hardware stack, and peripheral pin select (PPS) for flexible signal routing. The 10-bit ADC delivers up to 17 channels for sensor interfacing, while the 5-bit DAC supports setpoint generation for closed-loop analog control. The CWG module produces complementary PWM outputs with dead-band control for power-conversion and motor-drive stages. Typical applications include low-power IoT sensor nodes, home appliance control panels, LED lighting controllers, small motor control boards, industrial sensor transmitters, and battery-powered metering. The combination of low power, rich analog, and CIPs makes the PIC16F15345 well suited for systems that require deterministic real-time response without an external DSP, FPGA, or additional glue logic. When designing, allocate one 100 nF X7R decoupling capacitor per VDD pin placed within 3 mm of the lead, use the internal 32 MHz HFINTOSC unless precise baud rates are required, and reserve one CLC block for glue logic between peripherals. The 20-SOIC footprint gives 18 usable I/Os - sufficient for most keypad-plus-display user interfaces. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ צור קשר
PIC16F15345-I/SS - 8-bit 32MHz XLP MCU 14KB Flash | Microchip
PIC16F15345-I/SS

PIC16F15345-I/SS - 8-bit 32MHz XLP MCU 14KB Flash | Microchip

The Microchip Technology PIC16F15345-I/SS is an 8-bit PIC16F microcontroller running at up to 32 MHz with 14 KB Flash program memory and 1 KB SRAM, housed in a 20-pin SSOP package with industrial -40C to +85C temperature rating. The PIC16F15345-I/SS integrates essential peripherals including 4 PWMs, a 10-bit ADC, 5-bit DAC, comparator, complementary waveform generator (CWG), four configurable logic cells (CLC), and dual EUSART plus SPI/I2C interfaces. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and peripherals such as timers, ADCs, and communication interfaces. PIC16F MCUs from Microchip use a RISC (Reduced Instruction Set Computer) Harvard architecture with separate program and data buses. This category sits at the intersection of microcontrollers, embedded controllers, and CMOS logic ICs within the broader semiconductor taxonomy, and the PIC16F15345 belongs to Microchip's PIC16F153xx XLP family optimised for ultra-low-power, mixed-signal applications. The PIC16F15345-I/SS offers eXtreme Low Power (XLP) operation with multiple power-managed modes including doze, idle, and sleep. The device supports up to 32 MHz internal oscillator, 14 KB self-programmable Flash, 1 KB SRAM, 256 B EEPROM, and 18 dedicated I/O pins with interrupt-on-change capability on select pins. Peripheral pin select (PPS) is not present on this 20-pin variant, but the device exposes all standard peripherals via fixed pin assignments. The core employs an 8-bit RISC CPU with single-cycle execution for most instructions, an 8-level hardware stack, and a fast interrupt response. The instruction set is compatible with the broader PIC16 mid-range family, easing firmware portability. The CLC module allows combinatorial and sequential logic to be implemented in hardware without external glue logic, while the CWG produces complementary PWM outputs for half-bridge and full-bridge driver stages. Typical applications include low-power IoT sensor nodes, home appliance control, LED lighting controllers, battery-powered instrumentation, automotive body electronics sub-modules, and industrial sensor interfaces. The rich analog and digital peripheral mix also makes it suitable for fan control, small BLDC driver boards, and general-purpose embedded control where PIC16 code reuse is desired. When designing with the PIC16F15345-I/SS, verify the brown-out reset and watchdog timer configuration at startup, and ensure the ICSP programming pins (RA0/RA1) are not permanently pulled low in the application. The 20-pin SSOP package delivers compact board area for space-constrained designs. This page synthesises distributor pricing, SSOP-20 drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PIC16F15345T-E/GZVAO - 8-bit MCU, 14KB Flash, 32MHz | Microchip
PIC16F15345T-E/GZVAO

PIC16F15345T-E/GZVAO - 8-bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15345T-E/GZVAO is an 8-bit PIC microcontroller built on an enhanced mid-range core running at up to 32 MHz, integrating 14 KB of Flash program memory, 1 KB of RAM, and a rich set of Core Independent Peripherals (CIPs). Housed in a 20-pin UQFN (4x4 mm) package and supplied in Tape & Reel form, the part is specified for the -40C to +125C extended industrial temperature range and carries the Microchip "AO" (Automotive / OEM) designator in its suffix. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a mix of analog and digital peripherals behind a defined pin-out. PIC microcontrollers are widely used in 8-bit embedded designs and sit in the broader taxonomy of: microcontroller -> embedded processor -> semiconductor device. The PIC16F153xx family targets low-power, mixed-signal applications where deterministic Core Independent Peripherals offload timing-critical tasks from the core, and where eXtreme Low-Power (XLP) sleep modes are required for battery-powered products. Key features of the PIC16F15345T-E/GZVAO include 18 I/O pins, 4 PWM channels, a comparator, a 5-bit DAC, an ADC, a Complementary Waveform Generator (CWG), two EUSART modules, and SPI/I2C interfaces. The device supports 1.8V to 5.5V operation, multiple power-managed sleep modes, and on-chip debugging via ICD. The 20-UQFN (4x4) package provides a compact footprint suitable for space-constrained PCB designs in consumer, industrial, and automotive auxiliary modules. The architecture combines an 8-bit data path with hardware CIP blocks such as the CWG, NCO (Numerically Controlled Oscillator), and Configurable Logic Cells, allowing complex waveform generation and signal conditioning without CPU intervention. The eXtreme Low-Power (XLP) technology delivers nanoWatt sleep currents suitable for always-on IoT sensors and remote controls. Typical applications include IoT sensor nodes, consumer electronics user interfaces, LED lighting controllers, low-power wireless modules, automotive body and accessory ECUs, and small home appliances. The wide operating voltage range and rich peripheral mix make it a strong general-purpose 8-bit choice where deterministic hardware response and low standby current are required. When designing with this part, ensure that the UQFN-20 (4x4) land pattern is used and that the exposed pad is properly soldered for thermal dissipation. For migration within the PIC16F153xx family, the same 20-UQFN footprint is shared with PIC16F15344 and PIC16F15325, simplifying board re-use across feature scaling. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PIC16F15345T-E/SSVAO - 14KB Flash 8-bit MCU, 20-SSOP, AEC-Q100 | Microchip
PIC16F15345T-E/SSVAO

PIC16F15345T-E/SSVAO - 14KB Flash 8-bit MCU, 20-SSOP, AEC-Q100 | Microchip

The Microchip Technology PIC16F15345T-E/SSVAO is a 14KB Flash 8-bit PIC microcontroller from the PIC16(L)F153xx family, packaged in a 20-pin SSOP (0.209", 5.30mm width) with 18 I/O pins, rated for the automotive -40C to +125C temperature range and qualified to AEC-Q100 standards. It runs at 32 MHz, includes 1KB RAM, four PWM modules, a comparator, a 5-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), two EUSARTs, and both SPI/I2C peripherals, integrating intelligent analog and Core Independent Peripherals (CIPs) for low-power applications. What is a PIC 8-bit microcontroller? A PIC microcontroller is a single-chip computer based on a RISC Harvard architecture that combines a CPU, Flash program memory, RAM, EEPROM data memory, and configurable peripherals. The PIC16F153xx family specifically targets low-power (XLP) designs with autonomous CIPs that offload tasks like waveform generation, signal conditioning, and communication from the core, reducing active CPU time and extending battery life. Key features include 14KB Flash program memory, 1KB SRAM, 256B EEPROM, 18 general-purpose I/O pins, four 10-bit PWM outputs, a 10-bit ADC with up to 17 channels, a 5-bit DAC, two comparators with rail-to-rail inputs, two Enhanced USARTs, one SPI and one I2C, and eXtreme Low-Power (XLP) technology with typical sleep currents below 1 uA. The 32 MHz internal oscillator eliminates the need for an external crystal in many designs. Architecturally, the device uses a 14-bit instruction word, a modified Harvard memory layout, and Microchip's CIP block to execute peripheral interactions in hardware. The CWG, PWM, ADC, comparator, and DAC can be chained together without CPU intervention, making it well suited to motor control, lighting, and sensor front-end designs. Typical applications include automotive body and sensor nodes, IoT edge sensor nodes, LED lighting controllers, small BLDC and fan drivers, and consumer appliance user interfaces. The combination of AEC-Q100, wide temperature range, and SSOP-20 footprint makes it especially attractive for in-cabin automotive ECUs and HVAC controls. When designing, note that the 'E' temperature grade and 'VAO' suffix designate the automotive qualified (-40C to +125C) variant in tape-and-reel packaging. Always confirm pin assignment against the SSOP-20 diagram because the automotive grade adds specific test coverage that distinguishes it from the standard PIC16F15345-I/SS. This page synthesizes distributor pricing, AEC-Q100 automotive qualification details, and practical design notes not aggregated on a single manufacturer page.

RFQ צור קשר
PIC16F15345T-I/SO - 8-Bit MCU, 14KB Flash, 32MHz, 20-SOIC | Microchip
PIC16F15345T-I/SO

PIC16F15345T-I/SO - 8-Bit MCU, 14KB Flash, 32MHz, 20-SOIC | Microchip

The Microchip Technology PIC16F15345T-I/SO is an 8-bit PIC microcontroller from the PIC16(L)F153xx family with 14KB Flash program memory, 32MHz CPU speed, and integrated Intelligent Analog and Core Independent Peripherals (CIPs), housed in a 20-pin SOIC package. The device operates over a 2.3V to 5.5V supply range with eXtreme Low-Power (XLP) technology for energy-efficient designs. The "T" suffix indicates Tape and Reel packaging, and "I/SO" denotes the industrial temperature grade and SOIC-20 package. A PIC microcontroller is a programmable 8-bit RISC processor with integrated Flash, RAM, EEPROM, and peripherals on a single die, used widely in embedded control applications. The PIC16F153xx family extends Microchip's mid-range PIC16 line with rich analog and CIP blocks, targeting applications where deterministic behavior and low power are critical. It sits in the hierarchy: PIC16F -> mid-range 8-bit PIC -> microcontroller -> embedded computing. Key features of the PIC16F15345 include 14KB Flash program memory, 1024 bytes SRAM, 256 bytes EEPROM, 18 I/O pins, and four Configurable Logic Cells (CLC). The device integrates a 10-bit ADC with Computation, two 8-bit DACs, two comparators, a Complementary Waveform Generator (CWG), four 10-bit PWMs, two EUSART, SPI, and I2C. These peripherals enable sensor conditioning, signal generation, and communication without external components. The PIC16F15345 uses an enhanced mid-range 8-bit core with a 14-bit instruction word and 32MHz internal oscillator, providing 8 MIPS performance. Core Independent Peripherals such as CLC, CWG, and PWM operate without CPU intervention, reducing firmware complexity and enabling deterministic real-time response. The integrated 10-bit ADC with Computation performs hardware averaging and threshold comparison in the background. Typical applications include IoT sensor nodes, low-power battery-powered devices, LED lighting controllers, motor control, and consumer electronics. The XLP feature set makes it suitable for applications running from coin-cell or AA batteries, where standby currents below 50 nA extend battery life to years. When designing with this device, leverage the CIPs to offload tasks from the CPU and reduce firmware burden. Ensure decoupling caps (100 nF + 1 uF) are placed close to VDD/AVDD pins, and follow the unique layout guidelines in the PIC16F153xx datasheet for analog performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PIC16F15345T-I/SS - 8-Bit 32MHz 14KB Flash MCU | Microchip
PIC16F15345T-I/SS

PIC16F15345T-I/SS - 8-Bit 32MHz 14KB Flash MCU | Microchip

The Microchip Technology PIC16F15345T-I/SS is an 8-bit RISC PIC16F microcontroller featuring 14KB (8K x 14) of Flash program memory, 1KB of RAM, and a maximum CPU clock of 32MHz, housed in a 20-pin SSOP package. Part of the PIC16(L)F153xx family with eXtreme Low Power (XLP) technology, the device combines Intelligent Analog peripherals, Core Independent Peripherals (CIPs), and serial communication in a compact 20-pin footprint. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a programmable system-on-chip that integrates a CPU, Flash program memory, RAM, peripherals, and I/O on a single CMOS die. The PIC architecture (Peripheral Interface Controller) executes instructions on 8-bit data words, with separate program and data buses (Harvard architecture), enabling deterministic instruction timing. 8-bit MCUs belong to the broader category of microcontrollers (MCUs), which sit within embedded computing and semiconductor devices. The 'XLP' designation indicates eXtreme Low Power operating modes suitable for battery-powered and energy-harvesting designs. Key features of the PIC16F15345T-I/SS include 18 I/O pins, four 10-bit PWM outputs, a 10-bit ADC with computation, two comparators, a 5-bit DAC, two EUSART modules, SPI and I2C interfaces, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and a wide 2.3V to 5.5V operating voltage range. The -I temperature grade supports -40C to +85C industrial operation. Architecturally, the PIC16F15345 uses a 14-bit instruction word, four clock sources (HFINTOSC 16MHz selectable to 32MHz, LFINTOSC 31kHz, external crystal, external clock), and a 16-level hardware stack. The CIPs allow complex functions such as signal generation, waveform measurement, and motor control timing without CPU intervention. On-chip peripherals such as the Peripheral Module Disable (PMD) and Sleep with peripherals running enable nanoWatt XLP power consumption. Typical applications include low-power IoT sensor nodes, consumer appliance controls, battery-powered handheld instruments, LED lighting controllers, and small motor-control loops using the CWG and PWM combination. The CLCs enable glue-logic replacement and custom interface generation, useful in space-constrained designs that previously required discrete logic. When designing with the PIC16F15345T-I/SS, ensure decoupling capacitors (typically 100nF plus 10uF bulk) are placed close to VDD and VSS, follow the trace-length guidelines in the Microchip datasheet's Section 2.0 'Guidelines for Getting Started with PIC16(L)F153XX Microcontrollers', and verify the in-circuit serial programming (ICSP) connections for production-line firmware updates. The wide 2.3V-5.5V range allows direct 3.3V or 5V operation from a single-cell Li-ion or two AA batteries. This page synthesizes distributor stock and pricing, drop-in alternatives within the PIC16F153xx family, application-specific design guidance, and side-by-side comparison parameters - engineering context not found on a standalone manufacturer product brief.

RFQ צור קשר
PIC16F15354-E/5NVAO - 8-Bit 32MHz 7KB Flash MCU | Microchip | 28-VQFN
PIC16F15354-E/5NVAO

PIC16F15354-E/5NVAO - 8-Bit 32MHz 7KB Flash MCU | Microchip | 28-VQFN

The Microchip Technology PIC16F15354-E/5NVAO is an 8-bit PIC microcontroller from the PIC16F153xx family, offering 7KB (4K x 14 words) of Flash program memory, 512 bytes of RAM, and 32 MHz CPU speed in a 28-pin VQFN (6x6 mm) package with exposed pad. The /5NVAO suffix denotes the automotive grade ordering code variant with extended temperature support (-40C to +125C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and configurable peripherals. The PIC16 family belongs to the broader 8-bit microcontroller category, which sits below 16-bit (MSP430) and 32-bit (ARM Cortex-M) architectures in the embedded hierarchy. Within the power-management and mixed-signal landscape, 8-bit MCUs remain popular for cost- and power-sensitive applications such as sensor interfaces, LED control, and simple user-input handling. Key features include 10-bit ADC, 5-bit DAC, comparators, Core Independent Peripherals (CIPs), PWM modules, Peripheral Module Disable (PMD), and an integrated temperature sensor. The device operates from 2.3V to 5.5V supply, supports eXtreme Low-Power (XLP) modes with nanoWatt technology, and integrates multiple communication peripherals (I2C, SPI, EUSART). The 28-VQFN package with exposed thermal pad delivers a compact 6x6 mm footprint suitable for space-constrained designs. Architecturally, the PIC16F15354 uses Microchip's enhanced mid-range core with a 14-bit instruction word and 16-level hardware stack. The CIP blocks (CLC, COG, NCO, PWM, DSM) execute deterministic functions without CPU intervention, reducing latency and code complexity. The XLP Sleep mode can reduce current consumption to under 100 nA, making this part suitable for battery-powered and energy-harvesting applications. Typical applications include automotive body electronics, IoT sensor nodes, consumer white goods, LED lighting control, low-power remote controls, and battery management subsystems. The combination of integrated analog peripherals (10-bit ADC, comparators, 5-bit DAC, temperature sensor) makes it well suited for sensor signal conditioning and closed-loop control loops. When designing with this MCU, note that the /5NVAO suffix indicates an automotive-grade ordering code; verify AEC-Q100 qualification status with the manufacturer. For production programming, the device supports in-circuit serial programming (ICSP) via PGED/PGEC pins. The 28-VQFN exposed pad must be soldered to the PCB ground plane for thermal dissipation and electrical performance. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC16F153xx family, and practical design notes for automotive and low-power applications, providing information gain beyond what is in the manufacturer datasheet alone.

RFQ צור קשר
PIC16F15354-E/ML - 8-bit MCU, 7KB Flash, 32MHz, 28-QFN | Microchip
PIC16F15354-E/ML

PIC16F15354-E/ML - 8-bit MCU, 7KB Flash, 32MHz, 28-QFN | Microchip

The Microchip Technology PIC16F15354-E/ML is an 8-bit RISC microcontroller based on the PIC16 CPU core, delivering up to 32 MHz of computational performance and packaged in a 28-pin 6x6 mm QFN (ML) with extended (E) -40C to +125C temperature grade. The device integrates 7 KB (4K x 14 words) of self-programmable Flash program memory, 512 bytes of SRAM data memory, and 256 bytes of EEPROM, while exposing 25 general-purpose I/O lines across the 28-pin footprint. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and configurable peripheral blocks on one silicon die. Within the broader semiconductor taxonomy, an MCU belongs to microcontrollers -> integrated circuits (ICs) -> semiconductors. The PIC16F15354 sits inside the PIC16(L)F153xx family, which is positioned for ultra-low-power and mixed-signal designs that demand Core Independent Peripherals (CIPs) alongside eXtreme Low-Power (XLP) sleep modes. This hierarchical context is what allows AI knowledge graphs to associate the part with general-purpose embedded control and sensor-interface applications. Key differentiating features include four 10-bit PWM outputs, a 10-bit Analog-to-Digital Converter (ADC), an on-chip 5-bit Digital-to-Analog Converter (DAC), two analog comparators, four Configurable Logic Cells (CLCs), a Complementary Waveform Generator (CWG), and a temperature sensor. Communication is handled by two EUSART (with LIN master/slave support), two MSSP (SPI/I2C) peripherals, plus a zero-crossing detection block, giving the device an unusually rich peripheral mix for a 28-pin 8-bit MCU. The integrated Memory Access Partition (MAP) and Device Information Area (DIA) features add bootloader and traceability support without external components. Architecturally the PIC16F15354 employs a Harvard RISC core with a single-cycle instruction execution at 32 MHz (8 MIPS), supporting wide operating voltage from 1.8 V to 5.5 V on the 'F' variant (2.3 V to 5.5 V on the 'LF' low-voltage variant). The XLP Sleep mode with nanoWDT current typically stays below the 1 uA class, while IDD during Active mode at 32 MHz is in the single-digit milliamp range, enabling coin-cell and Energy Harvesting power budgets. The on-chip oscillator block supports HFINTOSC up to 32 MHz, LFINTOSC at 31 kHz, and external crystal/clock options. Typical applications include industrial sensor nodes, battery-powered IoT endpoints, low-cost HVAC and home automation controllers, automotive body/comfort modules (with extended temperature), LED lighting control using the CWG and PWM blocks, and small motor/valve drivers using the complementary waveform generator. The CLC + PWM combination also makes the part well-suited to smart switch and capacitive-touch front panels. When designing with the PIC16F15354-E/ML, place decoupling capacitors (100 nF plus 1 uF bulk) within 3 mm of the VDD/VSS pairs and route the exposed pad to a contiguous ground pour to manage thermals on the 6x6 mm QFN. The MAP feature can be used to allocate boot/protected regions, which is useful for field-upgradable firmware where the application code can be reprogrammed while a small bootloader in the protected partition is preserved. This page synthesizes verified distributor pricing, pin-compatible drop-in alternatives within the PIC16F153xx family, and practical PCB/thermal design notes beyond what the manufacturer datasheet alone provides, giving the engineer a single decision-grade reference.

RFQ צור קשר