उत्पाद (44,000+)

MKL14Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP | USB
MKL14Z64VLK4

MKL14Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP | USB

The NXP Semiconductors MKL14Z64VLK4 is an ultra-low-power 32-bit microcontroller built around an Arm Cortex-M0+ core operating at up to 48 MHz. It provides 64 KB of Flash program memory, 8 KB of SRAM, integrated USB connectivity, and an 80-pin LQFP package measuring 12 x 12 mm. Its operating supply range is 1.71 V to 3.6 V. An ultra-low-power microcontroller is a compact embedded-processing device designed to execute firmware while minimizing energy consumption during active operation and low-power states. The MKL14Z64VLK4 belongs to the Kinetis KL1 family and combines an Arm Cortex-M0+ processor, Flash memory, SRAM, analog interfaces, communication peripherals, and power-management functions in one package. This integration supports small, energy-conscious control systems without requiring multiple external chips. Key device attributes include 48 MHz maximum operating frequency, 64 KB of Flash memory, and 8 KB of SRAM. The 80-LQFP package provides a high pin count for mixed-signal, communication, and general-purpose embedded applications. The operating temperature range of -40°C to +105°C supports industrial and extended-temperature equipment, while the 1.71 V to 3.6 V supply range permits direct operation from common low-voltage rails. The Arm Cortex-M0+ architecture uses a simple instruction set and deterministic peripheral architecture suited to control loops, human-interface equipment, sensor nodes, and connected accessories. NXP describes the device as part of the Kinetis KL1x family, whose members share compatibility paths across the broader Kinetis KL portfolio. This makes the MKL14Z64VLK4 useful for designs that may later migrate to a device with more memory, performance, or peripheral integration. Typical applications include USB-connected control peripherals, industrial sensor modules, compact data loggers, building and access-control equipment, consumer accessories, and low-power embedded controllers. The USB connectivity is particularly useful when the product must enumerate as a standard USB device while retaining a small-footprint 80-LQFP package. The Cortex-M0+ core and 64 KB Flash also provide sufficient capacity for protocol handling, state-machine control, and local data processing. PCB design should follow the manufacturer pin and package guidance, particularly for decoupling, USB signal routing, analog inputs, and exposed supply pins. Confirm every peripheral assignment and alternate-function pin against the device pin description before routing the PCB. The 80-LQFP footprint also requires careful planning for via-in-pad or lead-exit strategies when assembly density and thermal performance are important. This product page combines the verified NXP product characteristics, package and memory details, sourcing options, same-family drop-in candidates, and practical implementation guidance. These engineering-focused details help distinguish a direct pin-compatible MCU from a broader functional equivalent before any board-level replacement is approved.

RFQ संपर्क
MKL15Z128VLH4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP | Kinetis
MKL15Z128VLH4

MKL15Z128VLH4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP | Kinetis

The NXP Semiconductors MKL15Z128VLH4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x ultra-low-power family, operating at up to 48 MHz with 128 KB of Flash and 16 KB of SRAM in a 64-pin LQFP (10x10 mm) package. It supports a wide operating voltage range from 1.71 V to 3.6 V and is qualified to AEC-Q100 for automotive applications, with an ambient operating temperature range of -40 °C to +105 °C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for deterministic interrupt response and ultra-low active power. MCUs sit within the hierarchy of embedded computing devices, beneath microprocessors and above simple digital signal controllers; the Kinetis L family specifically targets battery-powered and energy-harvesting designs where milliamp budgets dominate BOM decisions. Key features include an integrated 12-bit SAR ADC with up to 16 channels, a 16-bit ADC option, multiple low-power modes (Wait, Very-Low-Power Wait, Stop, VLLS0/1/3), and NXP's low-power touch sensor interface (TSI). Communications peripherals include I²C, UART, SPI, I²S, and USB 2.0 full-speed OTG with on-chip transceiver. The KL15 sub-family extends the KL0x with additional SRAM, communications options, and analog integration while retaining the same Cortex-M0+ instruction set. Architecturally the MKL15Z128VLH4 uses a 2-bit dual-core implementation with a single-cycle 32x32 hardware multiplier, a 4-channel DMA controller, and a low-leakage wake-up unit. The Flash is organized as 128K x 8 with ECC-style reliability, and the SRAM is 16 KB with parity. The part operates from internal or external references and supports a 4-bit GPIO port configuration across 53 usable I/O pins on the 64-LQFP. Typical applications include portable medical devices, wearable fitness trackers, home automation sensor hubs, automotive body controllers, smart-metering endpoints, USB-capable accessories (HID, game controllers, data loggers), and low-power industrial sensor nodes. The wide voltage range and on-chip USB OTG transceiver make it a common drop-in for legacy Freescale (now NXP) designs migrating to the Cortex-M0+ ecosystem. When designing with the MKL15Z128VLH4, ensure that the supply decoupling follows the KL15 reference manual (one 100 nF per VDD pin, one bulk 4.7 µF) and that the USB VBUS pin sees a regulated 5 V-tolerant rail per the USB OTG specification. For best low-power performance, enter VLLS0 with the low-leakage wake-up unit enabled and avoid leaving floating digital inputs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MKL15Z128VLH4R - ARM Cortex-M0+ 48MHz MCU, 128KB Flash | NXP
MKL15Z128VLH4R

MKL15Z128VLH4R - ARM Cortex-M0+ 48MHz MCU, 128KB Flash | NXP

The NXP Semiconductors MKL15Z128VLH4R is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller operating at 48 MHz with 128 KB of flash and 16 KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package with tape-and-reel packaging. As a member of the Kinetis KL1x family, the part integrates USB 2.0 OTG full-speed, flexible low-power modes, a 12-bit SAR ADC, and a rich set of serial peripherals. The 'R' suffix indicates tape-and-reel delivery, while the base MKL15Z128VLH4 ships in tray. The 64-LQFP package is the standard footprint across the KL14/KL15/KL16/KL17 families, enabling PCB reuse when scaling designs. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by Arm for energy-constrained embedded applications, featuring a 2-stage pipeline, single-cycle 32x32 multiplier, and Thumb-2 instruction set. It belongs to the broader hierarchy of ARM Cortex-M processors (Cortex-M0/M0+/M3/M4/M7), with the M0+ positioned as the most power-efficient tier while retaining full instruction compatibility with larger cores. Kinetis L series microcontrollers specifically target battery-powered and portable devices through aggressive use of multiple low-power modes (Run, Wait, Stop, VLPR, VLPW, VLPS, LLWU). Key features of the MKL15Z128VLH4R include 128 KB program flash, 16 KB SRAM, USB 2.0 full-speed OTG with on-chip transceiver, an 8-channel 12-bit ADC, two 16-bit timers, a low-power timer, RTC, CMP, and multiple serial communication modules (UART, SPI, I2C). The device supports 1.71V to 3.6V supply and provides 54 GPIO pins plus dedicated USB DP/DM. Hardware cryptography, tamper detection, and secure firmware update are not present on this KL15 sub-family, distinguishing it from the higher-end Kinetis K-series. From an architectural perspective, the M0+ core delivers 0.93 DMIPS/MHz while drawing only 9 uA/MHz in Run mode at 3V, and as low as 2.1 uA in VLPS mode with RTC retention. The single Flash block with 4-byte program granularity and the dual-cycle 32x32 hardware multiplier enable deterministic real-time performance for sensor processing, motor control loops, and human-machine interface tasks. Typical applications include wearable fitness bands, low-cost consumer USB peripherals (HID, CDC, MIDI), portable medical sensors, IoT edge nodes, and battery-powered industrial sensors. The integrated USB 2.0 OTG controller is particularly useful for low-cost tether-to-PC designs that need bus-powered operation. When designing with this part, prioritize supply decoupling (0.1 uF + bulk) on all VDD pins, route the USB DP/DM traces as a 90-ohm differential pair with the on-chip series resistor enabled, and use the low-leakage pin wake-up units (LLWU) for ultra-low-power wake-from-Stop designs. This page synthesizes distributor pricing, parametric comparison, and drop-in alternatives across the Kinetis L family and competing Cortex-M0+ MCUs - information not aggregated in any single manufacturer datasheet.

RFQ संपर्क
MKL15Z32VFT4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP
MKL15Z32VFT4

MKL15Z32VFT4 - 48MHz Cortex-M0+ 32KB Flash MCU | NXP

The NXP MKL15Z32VFT4 is an ARM Cortex-M0+ based ultra-low-power microcontroller from the Kinetis KL1x family, featuring 32KB flash, 4KB SRAM, and a 48 MHz core clock, housed in a 48-pin QFN (7x7 mm) package with exposed pad. What is a Kinetis KL1x microcontroller? The Kinetis KL1x is NXP's general-purpose ultra-low-power MCU family that builds on the KL0x family by adding more memory, communication peripherals, and analog options. The MKL15Z32VFT4 sits in this hierarchy as: microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> Kinetis family -> KL1x sub-family -> KL15 sub-sub-family. The Cortex-M0+ core itself is the smallest, most energy-efficient ARM core, designed for cost-sensitive embedded applications where deterministic low power matters more than raw performance. Key features include an operating voltage range of 1.71V to 3.6V, an industrial temperature range of -40C to +105C, a 12-bit ADC, multiple serial interfaces, low-power operating modes with sub-uA sleep currents, and an integrated 32KB flash memory array. The device also integrates a 16-bit SAR ADC, comparators, and a flexible low-power timer, making it suitable for battery-powered sensor products. Architecturally, the MKL15Z32VFT4 leverages the Cortex-M0+ core's two-stage pipeline and single-cycle I/O access, paired with NXP's low-leakage process technology and an integrated voltage regulator. The 48 MHz core clock delivers 0.93 DMIPS/MHz and supports both Thumb and Thumb-2 instruction subsets. The chip integrates up to 40 GPIO, multiple DMA channels, and a peripheral crossbar for flexible signal routing. Typical applications include wearable health monitors, battery-powered IoT sensor nodes, low-end consumer electronics, and industrial control nodes where energy harvesting or coin-cell operation is desired. The exposed thermal pad on the QFN package improves dissipation for sustained 48 MHz operation. When designing with this part, pay attention to the exposed pad (EP) connection to the ground plane for thermal and electrical performance. Use NXP's Kinetis Design Studio or MCUXpresso toolchain for firmware development, and ensure the brown-out and low-voltage detect settings match the battery chemistry profile. This page synthesizes distributor pricing, drop-in alternatives from the same Kinetis family, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
MKL15Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP
MKL15Z32VLK4

MKL15Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKL15Z32VLK4 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller operating at up to 48 MHz, with 32 KB of flash memory, 4 KB of SRAM, and an 80-pin LQFP package measuring 12 mm by 12 mm. It also includes a USB device controller and flexible clock options for energy-efficient embedded designs. A microcontroller is a programmable system-on-chip that combines a processor core, nonvolatile program memory, volatile data memory, and peripherals in one package. The MKL15Z32VLK4 belongs to the Kinetis KL1x family, which is positioned for low-power embedded control. Its hierarchy extends from Arm Cortex-M0+ microcontroller to 32-bit microcontroller, embedded processor, and mixed-signal semiconductor. Key features include a 48 MHz Arm Cortex-M0+ core, 32 KB flash for firmware, and 4 KB SRAM for working data. The integrated USB device controller supports designs that need a USB peripheral interface, while flexible clock options give designers more control over timing and power-management configurations. The 80-LQFP package provides enough pins for mixed-signal, communication, and general-purpose control interfaces. The device architecture centers on the low-power Cortex-M0+ core, which is designed for cost-sensitive and energy-efficient embedded applications. Flash memory provides a stable location for application code and configuration data, while SRAM accommodates working variables, stack usage, and peripheral data. The USB device controller adds a useful connectivity block without requiring a separate USB interface IC on designs that use the supported USB device function. Typical uses include USB-connected data loggers, compact industrial controllers, low-power sensor nodes, wearable or portable accessories, and embedded human-interface systems. The combination of 32 KB flash and 4 KB SRAM is suitable for small control loops, communication firmware, and moderate protocol stacks. Designs requiring larger code images or denser storage should evaluate higher-memory members of the Kinetis KL family. PCB implementation should preserve the exposed-pad and decoupling requirements stated in the manufacturer datasheet. Place the bulk and high-frequency bypass capacitors close to the supply pins, route sensitive analog and communication signals away from fast-switching nodes, and confirm all 80 pin assignments before releasing the layout. Firmware selection should use the device configuration and pin-muxing tables for the exact ordering code. This page combines the verified device identity, package characteristics, memory configuration, clock and USB features, compatible same-family options, and practical design guidance into one engineering reference. It also distinguishes the LQFP target from lower-pin-count members that may use similar ordering codes but require a different PCB footprint.

RFQ संपर्क
MKL15Z64VFT4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKL15Z64VFT4

MKL15Z64VFT4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP Semiconductors MKL15Z64VFT4 is an ARM Cortex-M0+ based ultra-low-power microcontroller from the Kinetis KL1x sub-family, offering 48 MHz CPU performance with 64 KB of embedded Flash and 8 KB of SRAM in a 48-pin QFN (7x7 mm) package. According to NXP product information, this MCU integrates connectivity peripherals including I2C, LINbus, SPI, UART/USART, and a Touch Sensing Interface (TSI), along with on-chip analog and timing peripherals for embedded designs. What is a Kinetis KL1x microcontroller? The Kinetis KL1x family is a general-purpose ultra-low-power 32-bit MCU line from NXP based on the ARM Cortex-M0+ core, succeeding the original Kinetis KL0x family with additional memory, communications, and analog peripheral options. Within the hierarchy, KL1x sits beneath Kinetis K-series Cortex-M4 parts (K10/K20/K40/K60) and above KL0x in NXP's ultra-low-power portfolio, providing a migration path to higher performance while preserving the same peripheral IP and toolchain. Key technical features include Brown-out Detect/Reset, Low-Voltage Detect (LVD), Power-On Reset (POR), Direct Memory Access (DMA), a Watchdog Timer (WDT), and PWM channels suitable for motor control or LED driving. The device runs from a single 3.3 V supply and supports a wide operating temperature range suitable for industrial applications. The integrated TSI block enables capacitive touch user interfaces without external touch controllers. Architecture-wise, the KL1x uses the efficient ARM Cortex-M0+ core with single-cycle I/O access, Thumb-2 instruction set, and a deterministic interrupt controller. The 64 KB Flash program memory is split into a primary block plus a separate FlexMemory or EEPROM emulation region depending on configuration, while the 8 KB SRAM provides ample space for protocol stacks and application state. Typical applications include ultra-low-power industrial sensor nodes, capacitive touch user interfaces, home appliances with LIN-bus connectivity, low-end consumer electronics, and battery-powered IoT edge devices. The combination of low-power modes, multiple serial interfaces, and TSI makes the KL1x well-suited to mains-powered and battery-powered products alike. When designing with this part, ensure the PCB footprint matches the 48-QFN (7x7) land pattern with proper thermal via arrangement under the exposed pad. The NXP Kinetis SDK and Processor Expert tooling provide firmware drivers; pin multiplexing must be configured via the PORT and SIM modules before peripheral activation. Selected power modes such as VLLS0/VLLS1 should be evaluated carefully against wakeup source requirements. This page consolidates distributor pricing, package-equivalent KL1x alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
MKL15Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL15Z64VLK4

MKL15Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL15Z64VLK4 is an ultra-low-power Kinetis KL1 microcontroller with an ARM Cortex-M0+ core, 48 MHz operating frequency, and 64 KB of Flash memory in an 80-pin LQFP package measuring 12 x 12 mm. It is designed for compact embedded systems requiring real-time control, USB connectivity, and integrated peripherals. The device operates from a 1.8 V to 3.3 V supply range and is identified as an industrial-temperature, AEC-Q100-capable option in catalog listings. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one package. The MKL15Z64VLK4 belongs to the Cortex-M0+ -> 32-bit RISC microcontroller -> embedded processor -> semiconductor hierarchy. Its compact 80-LQFP construction gives embedded designers access to general-purpose I/O and communication functions without requiring a separate external USB transceiver. The principal performance characteristics are a 48 MHz ARM Cortex-M0+ processor, 64 KB of Flash storage, and operation from 1.8 V, 2.5 V, or 3.3 V. NXP describes the part as an ultra-low-power device with USB connectivity and integrated peripherals for real-time embedded applications. These characteristics make it useful where deterministic control, modest program storage, and USB device support are required within a relatively small PCB footprint. The 80-LQFP package provides 80 terminal positions and a 12 x 12 mm body size. Its pin count offers more interface access than smaller microcontroller packages, which can reduce the need for external I/O expanders. The Gull Wing terminal form and square package shape also support conventional PCB assembly processes, although the exposed thermal behavior and routing density require careful layout review. Typical applications include USB-connected data acquisition, compact industrial controls, USB-to-serial or USB-to-GPIO accessories, sensor-interface nodes, and low-power embedded instrumentation. The 64 KB Flash capacity is suitable for compact control firmware, while the integrated USB interface can simplify host connectivity when the product requires enumeration, data transfer, or configuration over USB. Designers should confirm the complete pin assignment, alternate-function multiplexing, and power requirements from the NXP datasheet before layout. The device's multi-voltage capability does not remove the need for careful rail sequencing and decoupling, and USB signal routing should use controlled-impedance routing. Firmware development should also account for the limited 64 KB program-storage budget when application code, USB descriptors, and real-time control routines are combined. This product record combines the exact catalog identity, package and performance details, traceable manufacturer and distributor references, practical integration guidance, and strictly filtered drop-in alternatives. It is intended to help engineers evaluate PCB reuse, firmware constraints, power architecture, and connector requirements before committing MKL15Z64VLK4 to a new embedded design.

RFQ संपर्क
MKL16Z128VLH4 - 48MHz Cortex-M0+ MCU 128KB Flash LQFP-64 | NXP
MKL16Z128VLH4

MKL16Z128VLH4 - 48MHz Cortex-M0+ MCU 128KB Flash LQFP-64 | NXP

The NXP Semiconductors MKL16Z128VLH4 is a Kinetis KL16 ultra-low-power microcontroller featuring an ARM Cortex-M0+ core running at up to 48 MHz, with 128 KB of on-chip Flash and 16 KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package. It integrates a full-speed USB 2.0 device controller, 12-bit ADC, low-power timer (LPTMR), real-time clock (RTC), and multiple serial interfaces including UART, SPI, and I²C. An MCU (microcontroller unit) is a single-chip computer that integrates a processor core, memory, and programmable peripherals, sitting at the top of the embedded computing hierarchy: microcontroller -> microprocessor -> semiconductor. The Kinetis KL1x sub-family extends the KL0x with additional memory and connectivity, and the KL16 variant adds USB while maintaining the ultra-low-power modes that make Kinetis parts popular for battery-powered designs. Key features include 48 MHz maximum CPU frequency, 128 KB program Flash, 16 KB SRAM, USB 2.0 Full-Speed device with on-chip transceiver, 12-bit SAR ADC with up to 16 channels, multiple low-power modes (Wait, Stop, VLPR, VLPS), and a low-power timer that can run in all power modes. The 64-LQFP footprint (10x10 mm) provides ample GPIO for typical embedded applications. The KL16 architecture pairs an ARM Cortex-M0+ core (single-cycle 32-bit multiply, Harvard bus, NVIC with 32 interrupts) with NXP's ultra-low-power design techniques, including multiple clock gating domains and fast wake-up from low-power states. On-chip peripherals are mapped through an AIPS-Lite bus structure that simplifies DMA and interrupt routing for deterministic real-time behavior. Typical applications include wearable health and fitness devices, USB peripherals (HID, CDC, custom classes), home automation sensors, smart metering endpoints, and portable consumer electronics. The integrated USB 2.0 FS device eliminates the need for an external transceiver, reducing BOM cost in USB HID, CDC, or vendor-class device designs. When designing with this part, choose the correct Flash size variant in the family (KL16: 64KB/128KB/256KB) to match your code footprint. Take advantage of the multiple low-power modes for battery operation, but verify that any peripheral used in VLPS/VLPR is in the chip-specific low-power compatibility list. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers and procurement teams evaluate the MKL16Z128VLH4 for new designs and second-source decisions.

RFQ संपर्क
MKL16Z256VLH4 - 48MHz Cortex-M0+ 256KB Flash MCU | NXP
MKL16Z256VLH4

MKL16Z256VLH4 - 48MHz Cortex-M0+ 256KB Flash MCU | NXP

The NXP Semiconductors MKL16Z256VLH4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1 family, running at up to 48 MHz with 256KB (256K x 8) on-chip flash memory, housed in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, program memory, data memory, and peripherals on one die, serving as the compute element at the heart of embedded systems within the broader power-and-control hierarchy of modern electronics. The Kinetis KL series belongs to the class of ultra-low-power 32-bit MCUs built on the energy-efficient ARM Cortex-M0+ architecture. Key features of the MKL16Z256VLH4 include the FlexUSB module for USB device connectivity, an integrated segment LCD controller for direct glass drive, and the exceptional energy efficiency that defines the Kinetis L family, combining the ease of use of the Cortex-M0+ core with rich peripheral integration. Architecturally, the device pairs the two-stage Cortex-M0+ pipeline with NXP Kinetis peripheral sets, enabling scalable designs that can migrate across the Kinetis 32-bit portfolio while preserving software enablement. The 256KB flash provides ample room for protocol stacks such as USB HID/CDC classes and UI code driving the segment LCD. Typical applications include battery-powered human-machine interfaces with LCD displays, USB-connected sensor endpoints, consumer appliance panels, and industrial low-power monitoring nodes where energy efficiency and display capability matter. For design, plan USB and LCD pin assignments early, since the FlexUSB and segment LCD controller share the finite I/O pool of the 64-LQFP package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MKL16Z32VFT4 - 48MHz Cortex-M0+ MCU 32KB Flash | NXP
MKL16Z32VFT4

MKL16Z32VFT4 - 48MHz Cortex-M0+ MCU 32KB Flash | NXP

The NXP Semiconductors MKL16Z32VFT4 is a Kinetis KL16 series 32-bit microcontroller built on an Arm Cortex-M0+ core running at up to 48 MHz, integrating 32 KB of flash memory and 4 KB of SRAM in a 48-pin QFN (7x7 mm) package with exposed pad. It operates from a 1.8V, 2.5V, or 3.3V supply per distributor listings from Arrow and DigiKey. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest layer of the embedded-system hierarchy: MCU family (Kinetis KL1x) -> general-purpose MCU -> embedded processor -> semiconductor device. The KL1x family extends the ultra-low-power KL0x family with additional memory, communication, and analog peripheral options. Key features include the Cortex-M0+ core, the most energy-efficient Arm processor profile, delivering 48 MHz performance at very low dynamic current; 32 KB on-chip flash for program storage and 4 KB SRAM for data; and a rich peripheral set typical of the KL16 sub-family, including serial communication interfaces (UART, SPI, I2C), a 12-bit ADC, timers, and GPIO, plus low-power modes suited to battery-operated products. Technically, the Kinetis KL16 sub-family shares the same platform architecture as other Kinetis MCUs, with a crossbar bus, peripheral clock gating, and bitband-style GPIO control. The exposed-pad QFN package improves thermal and electrical performance versus a standard QFN, and the 7x7 mm footprint with 0.5 mm pitch suits compact two- and four-layer PCBs. Typical applications include portable and battery-powered consumer devices, sensor nodes and IoT end points, human-interface and touch sensing products, and small industrial control boards where ultra-low power and a small footprint matter more than raw processing throughput. A key design consideration is memory headroom: at 32 KB flash and 4 KB SRAM, code size and stack usage should be budgeted early, and the pin-compatible larger-memory siblings in the same package can be used as upgrade paths. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MKL16Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL16Z64VFM4

MKL16Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP

NXP Semiconductors MKL16Z64VFM4 is a 32-bit ARM Cortex-M0+ Kinetis KL1 microcontroller operating up to 48 MHz, with 64 KB of programmable flash memory and USB and analog peripherals in a 32-pin HVQFN package measuring 5 mm by 5 mm. The device targets low-power embedded systems where compact size, USB connectivity, and a general-purpose ARM microcontroller architecture are important. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface logic on one device. The Cortex-M0+ core belongs to the ARM microcontroller product hierarchy, where its compact instruction set and deterministic operation support cost-sensitive embedded control. Within NXP's product portfolio, the Kinetis KL1 family combines this efficient core with low-power design options and USB connectivity for connected peripherals, industrial controls, and compact consumer equipment. The MKL16Z64VFM4 provides 64 KB of flash, a 48 MHz maximum operating frequency, and a 32-bit architecture. Its integrated USB capability allows a design to communicate with a host without adding a separate USB interface controller. Analog peripherals support applications that must measure or control real-world signals, while the 5 mm by 5 mm HVQFN package reduces board area compared with larger leaded microcontrollers. Supported operating-voltage options listed for the device include 1.8 V, 2.5 V, and 3.3 V. The Kinetis architecture is suited to low-power embedded designs because the processor and peripherals are optimized for efficient control workloads. Flash memory retains programmed firmware when power is removed, and the Cortex-M0+ platform provides a familiar instruction set and development ecosystem. Because the MKL16Z64VFM4 has limited 64 KB flash capacity, firmware planning should account for code size, boot code, application logic, and configuration data before finalizing the product's feature set. Typical uses include USB-connected data loggers, compact industrial sensing modules, motor and valve controllers, access-control peripherals, and low-power instrumentation. A USB data logger can use the integrated interface for enumeration and data transfer, while an industrial controller can apply analog peripherals to sensor acquisition and digital outputs to actuators. The small package is especially useful when the PCB area is constrained but full-size leaded packages are undesirable. When laying out the PCB, place input, output, and decoupling capacitors close to their associated power pins, and route the exposed pad to the thermal and ground structure required by the manufacturer package drawing. Preserve USB-signal routing geometry and provide a clean, continuous ground path beneath the interface. Firmware and peripheral assignments should be checked against the manufacturer's reference manual and device configuration guidance before production. This product record combines the exact device identity, core, memory, frequency, package, connectivity, and sourcing information with same-family alternatives and practical integration guidance. It helps engineers assess whether the 32-pin Kinetis KL1 MCU matches a board footprint, power architecture, USB requirement, and embedded firmware budget before committing to a design.

RFQ संपर्क
MKL16Z64VFT4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP (Tape & Reel)
MKL16Z64VFT4

MKL16Z64VFT4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP (Tape & Reel)

The NXP MKL16Z64VFT4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x family, running up to 48 MHz with 64 KB of on-chip Flash and 8 KB of SRAM, supplied in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. The Kinetis KL16 sub-family targets general-purpose low-power applications that need USB connectivity, segment-LCD support, and a richer analog peripheral set than the entry-level KL0x family, while preserving the KL0x energy-efficiency envelope. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a fixed set of peripherals (timers, ADC, communication controllers, GPIO) into one package. The ARM Cortex-M0+ core used here is the most energy-efficient member of the Cortex-M family, designed for deterministic real-time control in cost-constrained embedded products. The Kinetis family sits within NXP's broader portfolio of 32-bit microcontrollers, which in turn belongs to the larger category of microcontrollers and microprocessors (semiconductor -> IC -> MCU -> Kinetis -> KL1x). Key specifications include a 48 MHz maximum core clock, 64 KB program Flash, 8 KB SRAM, USB 2.0 full-speed device with on-chip transceiver, segment-LCD driver (up to 8x36 or 4x40 segments), 12-bit SAR ADC with up to 16 single-ended channels, low-power UART/SPI/I2C peripherals, and an operating voltage range of 1.71 V to 3.6 V. The device also integrates a low-power RTC, multiple low-power modes (VLLS0..3, LLS, VLPR, STOP), DMA, and a low-power timer for periodic wake-up. The 48-QFN exposed-pad package provides a low thermal resistance and a compact 7x7 mm footprint for space-constrained boards. Architecturally, the KL16 combines a Cortex-M0+ core, single-cycle I/O bus, and a peripheral bridge feeding independent timer, communication, and analog subsystems. The on-chip voltage regulator supports internal core supply from a single external 1.71-3.6 V rail, eliminating the need for multiple external supplies. Hardware AES is not present on this sub-family, but the segment LCD controller, USB FS device, and 12-bit ADC give it strong suitability for human-interface, metering, and consumer products. Typical applications include battery-powered sensor nodes, USB-CDC or USB-HID consumer accessories, small appliances with segment-LCD displays, electronic shelf labels, low-end smart meters, and portable medical accessories. The integrated USB transceiver is a notable differentiator for cable-connected low-power peripherals. The combination of segment-LCD, USB, and Cortex-M0+ energy efficiency is uncommon at this price/performance tier. When designing with this part, allocate the exposed pad (EP) on the PCB as a solid copper pour connected to ground to meet thermal and electrical performance; route USB DP/DM as a 90 ohm differential pair and place the 48 MHz crystal within 5 mm of the XTAL pins. Decouple VDD/VREFL/VREFH with 100 nF ceramics placed as close as possible to the respective pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
MKL16Z64VFT4R - 48MHz Cortex-M0+ 64KB Flash MCU | NXP
MKL16Z64VFT4R

MKL16Z64VFT4R - 48MHz Cortex-M0+ 64KB Flash MCU | NXP

The NXP MKL16Z64VFT4R is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x family, running up to 48 MHz with 64 KB of on-chip Flash and 8 KB of SRAM, supplied in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. The Kinetis KL16 sub-family targets general-purpose low-power applications that need USB connectivity, segment-LCD support, and a richer analog peripheral set than the entry-level KL0x family, while preserving the KL0x energy-efficiency envelope. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a fixed set of peripherals (timers, ADC, communication controllers, GPIO) into one package. The ARM Cortex-M0+ core used here is the most energy-efficient member of the Cortex-M family, designed for deterministic real-time control in cost-constrained embedded products. The Kinetis family sits within NXP's broader portfolio of 32-bit microcontrollers, which in turn belongs to the larger category of microcontrollers and microprocessors (semiconductor -> IC -> MCU -> Kinetis -> KL1x). Key specifications include a 48 MHz maximum core clock, 64 KB program Flash, 8 KB SRAM, USB 2.0 full-speed device with on-chip transceiver, segment-LCD driver (up to 8x36 or 4x40 segments), 12-bit SAR ADC with up to 16 single-ended channels, low-power UART/SPI/I2C peripherals, and an operating voltage range of 1.71 V to 3.6 V. The device also integrates a low-power RTC, multiple low-power modes (VLLS0..3, LLS, VLPR, STOP), DMA, and a low-power timer for periodic wake-up. The 48-QFN exposed-pad package provides a low thermal resistance and a compact 7x7 mm footprint for space-constrained boards. Architecturally, the KL16 combines a Cortex-M0+ core, single-cycle I/O bus, and a peripheral bridge feeding independent timer, communication, and analog subsystems. The on-chip voltage regulator supports internal core supply from a single external 1.71-3.6 V rail, eliminating the need for multiple external supplies. Hardware AES is not present on this sub-family, but the segment LCD controller, USB FS device, and 12-bit ADC give it strong suitability for human-interface, metering, and consumer products. Typical applications include battery-powered sensor nodes, USB-CDC or USB-HID consumer accessories, small appliances with segment-LCD displays, electronic shelf labels, low-end smart meters, and portable medical accessories. The integrated USB transceiver is a notable differentiator for cable-connected low-power peripherals. The combination of segment-LCD, USB, and Cortex-M0+ energy efficiency is uncommon at this price/performance tier. When designing with this part, allocate the exposed pad (EP) on the PCB as a solid copper pour connected to ground to meet thermal and electrical performance; route USB DP/DM as a 90 ohm differential pair and place the 48 MHz crystal within 5 mm of the XTAL pins. Decouple VDD/VREFL/VREFH with 100 nF ceramics placed as close as possible to the respective pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
MKL17Z128VMP4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP
MKL17Z128VMP4

MKL17Z128VMP4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP

The NXP MKL17Z128VMP4 is a Kinetis KL17 ultra-low-power 32-bit microcontroller based on the ARM Cortex-M0+ core, operating at up to 48 MHz with 128 KB of flash and 32 KB of SRAM, housed in a 64-pin MAPBGA (5x5 mm) package. It targets battery-powered and energy-harvesting applications where active-mode performance and deep-sleep current must coexist in a small footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a set of on-chip peripherals such as timers, ADCs, and communication controllers. Cortex-M0+ parts occupy the ultra-low-power end of the ARM-M hierarchy and are typically used as microcontrollers -> embedded controllers -> semiconductor devices. The Kinetis KL1x family specifically adds segment-LCD controllers, USB-FS device, and richer analog compared to the entry-level KL0x line. Key features of the MKL17Z128VMP4 include a 16-bit SAR ADC with DMA support, 12-bit DAC, low-power timer, multiple low-power modes (VLLS0/1/3, LLPS, Stop, Wait, Run), flexible USB device (USB-FS) on selected variants, segment LCD controller up to 47 segments, and a 54 GPIO count. The 128 KB flash with 32 KB SRAM ratio makes it suitable for protocol stacks such as BLE HCI or Thread host layers while keeping peripheral support intact. Architecturally, the KL17 uses the Cortex-M0+ with a single-cycle multiplier and a 2-stage pipeline, achieving 0.93 DMIPS/MHz. The wide voltage range of 1.71 V to 3.6 V allows direct connection to single-cell Li-ion, coin cells, or regulated 3.3 V rails, while integrated DC-DC buck converter support simplifies multi-rail designs and improves efficiency in sleep modes where quiescent current drops below 1 uA. Typical applications include wearable fitness bands with segment-LCD displays, battery-powered wireless sensor nodes, USB-CDC/HID peripherals, industrial HMI panels with segment displays, and low-end home appliances. The combination of USB-FS, segment LCD, and low leakage makes the KL17 a strong fit for any 3.3 V coin-cell product that needs a bright display and a wired diagnostic port. When designing with this MCU, place the 0.1 uF decoupling capacitors as close as possible to each VDD/VSS pair and route the VBAT domain separately if a backup RTC battery is used. The segment-LCD bias network requires external charge-pump capacitors; insufficient capacitance leads to display ghosting at extreme temperatures below -20 C. This page synthesizes distributor pricing, drop-in Kinetis same-family alternatives, and practical design notes not consolidated on any single manufacturer page.

RFQ संपर्क
MKL17Z64VDA4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKL17Z64VDA4

MKL17Z64VDA4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP MKL17Z64VDA4 is a 32-bit ultra-low-power microcontroller based on the ARM Cortex-M0+ core running at 48 MHz, with 64 KB flash memory and 16 KB SRAM, housed in a 36-ball XFBGA (MAPBGA-36) package measuring just 3.5 x 3.5 mm. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest level of the embedded computing hierarchy (MCU -> embedded processor -> microprocessor -> SoC). The Kinetis KL family from NXP sits in the ultra-low-power tier of this hierarchy, targeting battery-operated and space-constrained designs where every microamp of current matters. Key features of the MKL17Z64VDA4 include the energy-efficient Cortex-M0+ core, 64 KB (64K x 8) of on-chip flash program memory for firmware storage, 16 KB of SRAM for data and stack, and USB connectivity as noted on the NXP product page. The extremely small 36-XFBGA package with 0.5 mm ball pitch enables placement on the underside of dense PCBs, freeing board area for sensors, radios, or displays in wearables and IoT end nodes. Technically, the device belongs to the Kinetis KL1x general-purpose ultra-low-power family, which provides additional memory, communications, and analog peripheral options beyond the entry-level KL0x family. The 48 MHz Cortex-M0+ executes Thumb instruction set code with a two-stage pipeline, delivering efficient real-time control with a compact gate count and correspondingly low dynamic and static power consumption. Typical applications include battery-powered wearable devices, smart sensors and IoT end nodes, portable medical accessories, and compact human-interface controllers where small footprint and low standby power dominate the selection criteria. When designing with a 3.5 x 3.5 mm BGA, plan the PCB with via-in-pad or escape routing to all 36 balls, and budget rework capability carefully since BGA inspection requires X-ray equipment. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with all pricing referenced as of 2026-10-18.

RFQ संपर्क
MKL17Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL17Z64VFM4

MKL17Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL17Z64VFM4 is an ultra-low-power 32-bit microcontroller with a 48 MHz ARM Cortex-M0+ core, 64 KB of flash memory, USB 2.0 connectivity, and a 32-pin QFN 5 x 5 mm package. It is designed for compact embedded products that require efficient processing, low-power operation, and USB connectivity in a surface-mount footprint. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Kinetis KL1 series combines an ARM Cortex-M0+ core with embedded flash and a selection of serial, analog, timing, and communication peripherals. The MKL17Z64VFM4 belongs to the low-power Kinetis family intended for battery-operated and portable embedded applications. Its principal characteristics include a 32-bit ARM Cortex-M0+ processor operating at 48 MHz, 64 KB of flash, and USB 2.0 support. The 64 KB program-memory capacity is suitable for compact firmware, protocol stacks, control logic, and human-interface applications. The 32-QFN package also reduces board area compared with leaded packages while supporting high-density automated assembly. The 48 MHz Cortex-M0+ architecture provides a practical balance between processing throughput, deterministic control, and low power consumption. Because the processor is designed for embedded workloads, the device can execute control tasks, manage peripherals, and service USB communications without requiring an external microprocessor. Exact SRAM capacity, operating-voltage limits, peripheral configuration, and current-consumption figures should be confirmed in the manufacturer datasheet before a power-sensitive design is released. Typical applications include low-power USB accessories, portable instrumentation, compact control systems, battery-operated equipment, and embedded human-interface devices. In each case, the 64 KB flash allocation supports a meaningful firmware image while the QFN package simplifies integration into compact assemblies. USB 2.0 is particularly useful for configuration, data logging, firmware updates, and connection to a host controller. PCB implementation should follow the manufacturer's land pattern, exposed-pad soldering guidance, and decoupling recommendations exactly. Confirm the board footprint against the 32-pin QFN 5 x 5 mm drawing before layout release, and validate thermal performance at the highest intended operating temperature. Firmware development should use the appropriate Kinetis SDK, configuration tools, and a debug interface compatible with the selected device variant. This product record combines the verified identity, core architecture, memory capacity, frequency, USB capability, package, and lifecycle information with application guidance, replacement considerations, and design-oriented comparison data. It is intended to help engineers identify whether the MKL17Z64VFM4 matches the memory, connectivity, footprint, and low-power requirements of a new embedded design.

RFQ संपर्क
MKL24Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL24Z64VFT4

MKL24Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL24Z64VFT4 is a 48 MHz Arm Cortex-M0+ microcontroller with 64 KB of embedded flash memory, 8 KB of SRAM, and a full-speed USB 2.0 controller in a 48-QFN 7 x 7 mm package. It combines general-purpose embedded processing with USB connectivity and an ultra-low-power design intended for compact, low-energy embedded products. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MKL24Z64VFT4 belongs to the Kinetis KL2x family, combining an Arm Cortex-M0+ core with USB 2.0 connectivity. This places it within the hierarchy of embedded processor, microcontroller, Kinetis L-series MCU, and low-power semiconductor, making it suitable for systems that require compact control and USB communication without a separate USB interface device. The device operates at up to 48 MHz and includes 64 KB of flash for firmware and 8 KB of SRAM for working memory. Its full-speed USB 2.0 capability supports USB device or OTG-oriented designs, while the Kinetis L-series integration includes analog and timing peripherals for embedded measurement and control. The 48-QFN package also exposes a compact land pattern for space-constrained PCB layouts. The Arm Cortex-M0+ architecture provides a straightforward low-complexity software platform for control loops, human-interface devices, portable instruments, and connected accessories. NXP describes the Kinetis KL2x family as pin, software, and tool compatible with other Kinetis L-series MCU families, supporting migration between related Kinetis designs. Firmware development therefore benefits from the broader Kinetis software ecosystem and reusable peripheral-driver patterns. Typical uses include low-power USB data loggers, compact sensor interfaces, USB-connected test equipment, and portable measurement instruments. A designer can place the MCU beside a sensor or transducer, run control and sampling routines from flash and SRAM, and use the integrated USB controller for configuration, data transfer, or firmware updates. The exact USB operating mode and peripheral allocation must be confirmed against the selected device configuration in the manufacturer datasheet. PCB implementation requires careful treatment of the exposed pad, power rails, decoupling, and USB signal routing. Keep the USB D+ and D- traces short and impedance-controlled, provide the decoupling network specified by the datasheet, and use a thermal-via pattern beneath the exposed pad when required by the PCB stack-up. Confirm all VDD, VDDUSB, VDDIO, ground, reset, and programming pins against the package drawing before fabrication. This page combines the exact MKL24Z64VFT4 identity and package information with lifecycle, pricing, sourcing, and interface details. It also organizes verified same-brand alternatives and practical implementation guidance for engineers comparing the KL2x family with adjacent Kinetis L-series devices.

RFQ संपर्क
MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP
MKL24Z64VLH4

MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP

The NXP Semiconductors MKL24Z64VLH4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built on the Arm Cortex-M0+ core, operating up to 48 MHz with 64 KB of embedded Flash memory (64K x 8 organization), 8 KB of SRAM, and a crystal-less full-speed USB 2.0 device controller, all housed in a 64-LQFP (10 x 10 mm) package. The device runs from a single 1.71 V to 3.6 V supply, so it fits industrial 3.3 V rails, 2.5 V legacy systems, and coin-cell powered portable products from the same design. A microcontroller (MCU) is a single integrated circuit that bundles a CPU core, program memory, working RAM, and peripherals such as GPIO, timers, and communication controllers on one die. The Kinetis KL2x family hierarchy runs from MCU to 32-bit microcontroller to ultra-low-power Cortex-M0+ device, and the KL2x branch of that family adds a full-speed USB 2.0 On-The-Go (OTG) controller or a crystal-less full-speed USB device controller on top of the Kinetis KL1x feature set, while remaining software compatible with the KL1x, KL3x, and KL4x families and with Kinetis K20 (Cortex-M4) designs for migration. Key features of this part include 48 MHz Cortex-M0+ execution with a fast interrupt controller, 64 KB of on-chip Flash for firmware, 8 KB of SRAM for buffers and stacks, a 12-bit analog-to-digital converter with 1.71 V to 3.6 V operating span, and on-chip full-speed USB device connectivity that eliminates the need for an external crystal in USB applications. Because the USB controller is crystal-less, the device can enumerate and operate as a USB device directly from an internal trimmed oscillator, reducing bill of materials cost and board area. Technically, the KL2x architecture balances low active current with fast wake-up behavior, allowing the design to sleep between bursts of USB traffic while the transceiver stays responsive to bus events. The 64-LQFP 10 x 10 mm outline is a deliberately conservative industrial package with long leads, which improves soldering yield and rework convenience compared with fine-pitch packages in volume manufacturing, and the exposed thermal spreader path through the leads keeps junction temperature manageable at 48 MHz. Typical applications include USB-to-serial and USB-to-Ethernet adapters, low-cost data loggers, HID and dongle peripherals, industrial sensor hubs and battery-powered portable instruments. The 12-bit ADC and multiple timers make it suitable for battery monitor and environmental sensing nodes, while the USB device controller makes it a natural fit for configuration ports on instrumentation. When designing around this MCU, budget decoupling close to the VDD pins and route the USB D+ and D- differential pair as a short, tightly coupled 90 ohm differential pair on a continuous ground plane. Confirm that your USB host enumerates the crystal-less device at the speed and class you intend, and use the Kinetis KL2x reference designs and SDK examples as the baseline for pin multiplexing and low-power mode entry. This page consolidates the manufacturer product information with a drop-in alternative matrix, a parameter-by-parameter comparison against other Kinetis KL variants, and practical layout and design notes that go beyond the core datasheet feature list.

RFQ संपर्क
MKL24Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL24Z64VLK4

MKL24Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP MKL24Z64VLK4 is a 32-bit Arm Cortex-M0+ Kinetis KL2 microcontroller operating up to 48 MHz, with 64 KB of embedded Flash memory, 8 KB of SRAM, and full-speed USB 2.0 connectivity. The device is offered in an 80-pin FQFP/LQFP package measuring 12 mm by 12 mm and is intended for compact, low-power embedded systems. Its operating supply range extends from 1.71 V to 3.6 V, with an industrial temperature range of -40 °C to +105 °C. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The MKL24Z64VLK4 belongs to the Kinetis KL2x family, which combines an Arm Cortex-M0+ processor with ultra-low-power design features and USB support. Its position within the broader hierarchy is Arm Cortex-M0+ embedded processor, 32-bit microcontroller, Kinetis MCU, and semiconductor. The KL2x family is positioned for low-power embedded applications requiring more connectivity than the earlier KL1x family. Key device characteristics include 64 KB of Flash for firmware, 8 KB of SRAM for working data, operation up to 48 MHz, a 12-bit analog-to-digital converter, and full-speed USB. The 80-pin package provides access to the family’s analog, timing, communication, and general-purpose I/O resources. The 1.71 V to 3.6 V operating range supports low-voltage portable, industrial, and connected embedded equipment, while the -40 °C to +105 °C rating supports temperature-controlled industrial environments. The Arm Cortex-M0+ core supports a compact instruction set and an event-driven architecture suited to control tasks, sensor monitoring, human-interface functions, and low-power background processing. Full-speed USB adds a practical path for connected peripherals, configuration tools, data logging, and firmware update workflows. Because the device combines USB and low-power operation, it can bridge host-device communication duties with embedded control rather than requiring a separate USB interface controller. Typical applications include USB-connected sensor nodes, industrial condition-monitoring equipment, compact data loggers, USB human-interface devices, industrial control panels, and low-energy embedded systems. The 64 KB Flash capacity is appropriate for moderate firmware loads, and the 8 KB SRAM is sufficient for typical control loops and small data buffers. Designs requiring substantially larger application code, extensive graphics storage, or complex protocol stacks should assess whether another MCU in the Kinetis portfolio offers more memory. When laying out the PCB, preserve the pin assignments and exposed-connection requirements defined by the manufacturer datasheet, especially for USB D+ and D− routing. Place USB differential traces as a controlled-impedance pair with minimal stubs and provide suitable decoupling near the power pins. Firmware development should use an NXP-supported toolchain and verify clock, reset, boot, and low-power configurations against the device reference manual before production. This product page consolidates the confirmed MCU specifications, package and supply information, lifecycle status, family context, sourcing options, and design-oriented selection guidance. It also distinguishes the 80-pin target from the 64-pin MKL24Z64VFM4 package variant so engineers can avoid an invalid footprint substitution.

RFQ संपर्क
MKL25Z128VLK4 - 48MHz Cortex-M0+ 128KB MCU | NXP
MKL25Z128VLK4

MKL25Z128VLK4 - 48MHz Cortex-M0+ 128KB MCU | NXP

The NXP Semiconductors MKL25Z128VLK4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built around an Arm Cortex-M0+ processor operating at 48 MHz, with 128 KB of flash memory and an 80-pin LQFP package measuring 12 x 12 mm. It is suited to embedded control, USB-connected sensing, portable instrumentation, and low-power edge systems. According to the distributor records, the device also provides 16 KB SRAM and full-speed USB. A microcontroller is a compact computer integrated with nonvolatile program memory, working RAM, digital peripherals, and I/O interfaces. It executes firmware, samples sensors, controls actuators, and manages communications without requiring a separate processor. The MKL25Z128VLK4 belongs to the hierarchy Kinetis KL25 microcontroller -> Arm Cortex-M0+ MCU -> 32-bit microcontroller -> embedded processor -> semiconductor. Its principal features include 128 KB of flash for firmware storage, 16 KB of SRAM for runtime data, a 48 MHz Cortex-M0+ core, and full-speed USB. The 80-LQFP package provides enough external connections for mixed-signal products, interface-heavy controls, and designs that favor a leaded package for inspection or assembly. The Kinetis KL2x family also supports migration paths across Kinetis KL1x, KL2x, KL3x, and KL4x devices, as stated by NXP. The Cortex-M0+ architecture favors energy-efficient embedded execution while retaining a conventional 32-bit instruction set and integrated interrupt handling. Flash capacity allows substantially larger applications than 64 KB-class devices, while SRAM supports packet buffers, sampled data, display or communication state, and real-time control tasks. USB integration can reduce the external controller count in connected products. Typical uses include USB data loggers, building-control endpoints, compact industrial monitors, sensor-hub boards, access-control terminals, and low-power portable instruments. The 48 MHz processing rate is suitable for concurrent USB traffic, control loops, protocol handling, and supervisory tasks where workload is modest enough not to require a higher-performance Cortex-M core. Designers should preserve the package pin assignments, supported supply ranges, decoupling requirements, and clock configuration when creating a PCB. The 80-LQFP footprint also requires adequate solder-mask clearance and inspection because its closely spaced leads can complicate manual rework. Firmware development should account for memory-map constraints, USB clocking, peripheral pin multiplexing, and low-power state transitions. This product page consolidates verified manufacturer and distributor identity data, sourcing links, application guidance, and compatibility analysis. Because the supplied sources do not expose complete electrical ratings, pricing values, or a verified pin list, missing fields are explicitly marked rather than inferred.

RFQ संपर्क
MKL25Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP
MKL25Z32VLK4

MKL25Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKL25Z32VLK4 is a 32-bit Kinetis KL2 microcontroller with a 48 MHz Arm Cortex-M0+ core, 32 KB of flash memory, 4 KB of SRAM, and full-speed USB support in an 80-pin LQFP package measuring 12 x 12 mm. The device belongs to the Kinetis KL2x ultra-low-power family and supports operation from 1.8 V, 2.5 V, or 3.3 V supply levels. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one package. The Arm Cortex-M0+ core provides a compact, energy-efficient architecture for embedded control, while the Kinetis family extends this core with low-power operating modes, general-purpose I/O, communication peripherals, and USB connectivity. In the system hierarchy, the MKL25Z32VLK4 is a microcontroller, semiconductor, and programmable embedded-control component. Key features include a 48 MHz operating frequency, 32 KB flash organized as 32K x 8, and 4 KB SRAM. The KL2x family adds a full-speed USB 2.0 controller, with the selected device identified as supporting full-speed USB OTG. Its 80-LQFP package provides 80 external terminals, making it suitable for designs that need broader peripheral access than smaller MCU packages can offer while avoiding a ball-grid-array assembly. The MKL25Z32VLK4 is based on the Arm Cortex-M0+ instruction set, which prioritizes compact code size and efficient real-time control rather than high-performance computing. Its 32 KB flash stores the application firmware, while 4 KB SRAM supports stack space, variables, buffers, and USB or serial-data handling. The manufacturer describes the Kinetis KL2x family as ultra-low-power and notes compatibility with other Kinetis KL1x, KL2x, KL3x, and KL4x devices for migration paths, subject to peripheral and pin-level review. Typical applications include USB-connected data acquisition, compact control panels, industrial sensor nodes, wearable accessories, and embedded USB peripherals. The 48 MHz Cortex-M0+ core is useful for responsive control tasks, and the integrated USB controller can simplify connectivity compared with a discrete USB interface. A board-level design still needs suitable voltage regulation, clocking, decoupling, USB routing, and firmware configuration. Designers should match the exact 80-pin LQFP footprint and verify peripheral assignments, USB implementation details, and board-level connectivity against the NXP documentation before layout. Stable supply voltage and correctly sized local decoupling are fundamental because processor and USB activity can produce fast transient current. USB signal routing also requires controlled impedance and careful placement of the protection and termination network. This product page combines the exact NXP and distributor identification, distinguishes verified electrical facts from unspecified details, identifies same-family migration candidates, and highlights PCB, power, and USB design considerations that help engineers evaluate the MKL25Z32VLK4 beyond a basic catalog description.

RFQ संपर्क
MKL25Z64VFM4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP
MKL25Z64VFM4

MKL25Z64VFM4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP

The NXP Semiconductors MKL25Z64VFM4 is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 48 MHz, with 64 KB of flash memory, 8 KB of SRAM, and full-speed USB support in a 32-pin HVQFN package measuring 5 mm by 5 mm. The device combines a low-power MCU architecture with analog and digital peripherals for compact embedded systems. A microcontroller is an integrated circuit that executes embedded software, reads sensor inputs, controls actuators, and manages communication interfaces. The MKL25Z64VFM4 belongs to the Kinetis KL2 ultra-low-power MCU family, placing it within the hierarchy of embedded microcontroller, ARM Cortex processor, and low-power embedded-system device. Principal features include a 48 MHz ARM Cortex-M0+ core, 64 KB of flash organized as 64K by 8 bits, and 8 KB of SRAM. The part also includes a full-speed USB controller, analog and digital peripherals, and support for 1.8 V, 2.5 V, and 3.3 V operation. Its 32-pin HVQFN package supports dense PCB layouts without relying on a large leaded package. The Kinetis KL2 architecture is designed for embedded applications where processing capability, USB connectivity, and low-power operation must coexist in a compact footprint. The 64 KB flash capacity provides room for bootloader code, application firmware, configuration data, and USB device functions, while the 8 KB SRAM allows real-time tasks and peripheral buffering without external memory. Typical uses include USB-connected sensors, compact data loggers, industrial interface modules, portable measurement equipment, and low-power embedded controllers. The full-speed USB interface can simplify connection to a host system, while the Cortex-M0+ core provides a common architecture for firmware development and peripheral control. PCB design should account for the exposed pad beneath the HVQFN package, provide adequate thermal and electrical grounding, and place decoupling capacitors close to the supply pins. USB routing requires careful control of trace geometry and return paths, and firmware should use the manufacturer's clock, power-management, and USB initialization procedures. This product page combines the core Kinetis KL25 specifications, package information, design guidance, and qualified drop-in alternatives to support component selection, firmware planning, PCB layout, and replacement decisions without requiring engineers to reconstruct the design context from separate documents.

RFQ संपर्क
MKL25Z64VLH4 - 48MHz Cortex-M0+ USB MCU | NXP Semiconductors
MKL25Z64VLH4

MKL25Z64VLH4 - 48MHz Cortex-M0+ USB MCU | NXP Semiconductors

NXP Semiconductors MKL25Z64VLH4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built around an Arm Cortex-M0+ processor operating up to 48 MHz. It provides 64 KB of Flash memory, 8 KB of SRAM, integrated full-speed USB connectivity, and a 64-LQFP 10 mm × 10 mm package for compact embedded systems. A microcontroller is a semiconductor device that integrates a processor core, programmable memory, peripheral interfaces, and power-management functions on one package. The Cortex-M0+ core combines a compact instruction set with efficient exception handling for embedded control. Within the product hierarchy, the MKL25Z64VLH4 belongs to the Kinetis L series of ultra-low-power microcontrollers, combining general-purpose control, serial connectivity, and USB device or OTG-oriented functions. The 48 MHz maximum operating frequency supports responsive control loops and efficient handling of embedded workloads, while 64 KB of Flash preserves room for firmware, configuration data, and application code. The 8 KB SRAM supports working memory, stack allocation, buffering, and communication tasks without requiring an external memory interface in typical designs. Full-speed USB integration enables direct peripheral connectivity for data acquisition, configuration, logging, and human-interface applications. The device supports 1.8 V, 2.5 V, and 3.3 V operating configurations according to the product listing information. This voltage flexibility makes it suitable for mixed-voltage embedded systems, although power-supply sequencing, decoupling, and signal-level limits must be checked against the manufacturer datasheet before implementation. Its ultra-low-power positioning is useful for systems that spend substantial time idle, sleep, or operating at reduced clock rates. Typical applications include USB-connected data loggers, industrial interface modules, compact control boards, portable measurement equipment, and low-power embedded products. The 64-LQFP package exposes more general-purpose I/O than smaller microcontroller packages and remains practical for automated assembly, inspection, and prototype rework. Software development is supported through the wider Kinetis ecosystem, subject to the exact peripheral configuration of the selected device. PCB design should preserve short return paths for digital supplies and sensitive analog inputs, place decoupling capacitors close to their associated supply pins, and keep high-current or switching-node connections away from communication and measurement traces. USB routing also requires controlled impedance, suitable trace geometry, and compliance with the applicable device and interface-layout requirements in the manufacturer datasheet. This product overview consolidates the principal device identity, memory capacity, clock rate, USB capability, package information, sourcing guidance, and design considerations into a compact engineering reference for initial component selection and PCB planning.

RFQ संपर्क
MKL26Z128CAL4R - 48MHz Cortex-M0+ 128KB Flash MCU | NXP
MKL26Z128CAL4R

MKL26Z128CAL4R - 48MHz Cortex-M0+ 128KB Flash MCU | NXP

The NXP MKL26Z128CAL4R is a Kinetis KL26 sub-family 32-bit ARM Cortex-M0+ microcontroller running up to 48 MHz, integrating 128 KB of flash and 16 KB of SRAM, with a full-speed USB 2.0 device controller (crystal-less capable), and packaged in a compact 36-ball WLCSP measuring approximately 2.37 mm x 2.46 mm. It is one of the lowest-power Kinetis Cortex-M0+ MCUs in NXP's ultra-low-power portfolio, designed for portable and battery-powered applications where PCB real estate is at a premium. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and GPIO. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for deterministic interrupt response and minimal gate count. Microcontrollers sit at the heart of embedded systems, providing local intelligence for sensors, actuators, user interfaces, and connectivity functions across consumer, industrial, and IoT markets. Key features of the MKL26Z128CAL4R include the Cortex-M0+ core with single-cycle multiplication, an integrated low-power USB 2.0 full-speed device controller that eliminates the need for an external crystal, multiple low-power modes (Run, Wait, Stop, VLPR, VLPW, VLPS, LLS, VLLSx), a 12-bit SAR ADC, high-speed analog comparators, a real-time clock, and a flexible low-power timer (LPTMR). The device supports 1.71 V to 3.6 V supply operation and is offered in a tiny 36-ball WLCSP for space-constrained designs such as wearables and USB dongles. The MKL26Z128CAL4R uses a 32-bit ARMv6-M architecture with the Thumb/Thumb-2 instruction set, giving it strong code density while keeping silicon area small. Its multi-mode low-power architecture allows peripherals like the ADC and comparators to operate in low-power modes independently of the CPU, reducing total system energy. The inclusion of an integrated USB PHY with on-chip 3.3 V regulator and a 1 kHz low-power timer makes it attractive for always-on, event-driven products. Typical applications include USB HID peripherals (keyboards, mice, game controllers), wearable fitness bands, BLE/ZigBee host microcontrollers, sensor hub MCUs, low-end medical sensors, and compact IoT end nodes. The crystal-less USB and tiny WLCSP package make it especially attractive for USB dongles, gaming peripherals, and other form-factor-constrained consumer electronics. When designing with the MKL26Z128CAL4R, pay attention to the WLCSP PCB layout - the 0.4 mm ball pitch requires HDI PCB manufacturing and careful via.2.3 pad design for reliable assembly. Provide adequate decoupling (one 100 nF and one 4.7 uF X5R ceramic) within 2 mm of the power pins to maintain supply integrity during USB transitions. This page synthesizes distributor pricing, drop-in alternatives within the same WLCSP-36 footprint, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क