उत्पाद (44,000+)

MPC852TCVR100A - 100MHz PowerQUICC MPU, 256-BGA | NXP
MPC852TCVR100A

MPC852TCVR100A - 100MHz PowerQUICC MPU, 256-BGA | NXP

The NXP MPC852TCVR100A is a PowerQUICC MPC8xx microprocessor with a 32-bit Power Architecture core running at 100 MHz, fabricated in a 0.18 micrometer CMOS process and housed in a 256-pin PBGA package measuring 23 mm by 23 mm. An MPU, or microprocessor unit, is the central processing element of an embedded system; in the broader taxonomy, it sits above a microcontroller (MCU) and below a system-on-chip (SoC), handling complex control-plane tasks with an external memory bus and peripherals. The MPC852T family is part of NXP's (formerly Freescale / Motorola) PowerQUICC line, which integrates a PowerPC core with a separate communications processor module (CPM) to offload networking and serial I/O tasks. Key features include 100 MHz core speed, 3.3 V I/O operation with a 1.8 V internal core voltage, integrated CPM for Ethernet and serial communications, integrated timers and interrupt controller, and a 32-bit external memory bus supporting DRAM, SRAM, and ROM. The 256-PBGA package exposes the full 32-bit data bus plus dedicated Ethernet, SCC, and other peripheral pins. Operating temperature range spans -40 C to +100 C, supporting industrial and extended-commercial environments. Architecturally, the MPC852T pairs a 32-bit PowerPC core with the CPM coprocessor that handles DMA-driven Ethernet MACs, serial communications controllers (SCCs), serial management controllers (SMCs), and a USB interface. The dual-engine approach offloads the main core from packet processing, delivering deterministic throughput for telecom line cards, routers, and industrial control nodes. The 0.18 micrometer process allows the 100 MHz operation at modest power consumption for its class. Typical applications include Ethernet-to-Ethernet line cards, industrial routers and protocol bridges, telecom control-plane processors, factory automation controllers, and legacy PowerQUICC designs where software compatibility with the MPC860 family is required. The integrated CPM makes it a natural choice for any design requiring deterministic serial or Ethernet throughput alongside a general-purpose CPU. When designing with this part, note that NXP has marked the MPC852T family for end-of-life per the official product page, so new designs should evaluate active PowerQUICC II (MPC82xx) or QorIQ successors. Existing designs should consider last-time-buy stocking and verify pin compatibility of any proposed cross-reference against the original 256-PBGA layout. This page synthesizes distributor pricing, drop-in PowerQUICC alternatives, and end-of-life replacement guidance not found in a single datasheet, supporting engineers planning either new designs or field replacements.

RFQ संपर्क
MPC852TCVR50A - 50MHz PowerQUICC MPU, 256-BGA | NXP
MPC852TCVR50A

MPC852TCVR50A - 50MHz PowerQUICC MPU, 256-BGA | NXP

The NXP MPC852TCVR50A is a 50 MHz PowerQUICC communications processor built on a 32-bit Power Architecture core, integrating a peripheral DMA-driven Communications Processor Module (CPM) alongside a general-purpose embedded core, housed in a 256-pin PBGA package (23x23 mm). It targets cost-sensitive telecom and industrial control applications where an integrated Ethernet MAC, RISC engine, and DRAM controller replace multi-chip designs. A PowerQUICC microprocessor is a member of the PowerPC embedded family that pairs a CPU core with a dedicated communications engine for offloading packet processing. Conceptually it sits within the broader taxonomy: microprocessor -> embedded processor -> communications processor (PowerQUICC). The CPM, driven by microcoded RISC controllers, executes protocol tasks for serial, Ethernet, and ATM layers while the main core handles control-plane code, allowing deterministic throughput without high host CPU utilization. Key features of the MPC852TCVR50A include 50 MHz core/CPM operation, 32-bit data path, integrated 10/100-capable Ethernet (10 Mbps Ethernet port), 8 KB unified cache, and DRAM controller support. The device supports industrial-grade temperature operation up to +100C, and exposes PCI, UPM, and GPCM external bus interfaces alongside on-chip CPM serial channels (SCC/SMC) for serial protocol bridging. Architecturally, the MPC852T pairs an embedded PowerPC core with a CPM built around dedicated RISC serial controllers, achieving deterministic wire-rate serial handling. The part is fabricated on a 0.18 um CMOS process and operates from a 3.3 V I/O supply with separate 1.7 V to 1.9 V core rails typically generated by an external controller; this dual-rail design reduces power dissipation versus single-rail 5 V predecessors. Typical applications include ISDN router line cards, DSLAM control planes, Ethernet-to-serial bridging, low-end industrial routers, and legacy PBX/VoIP gateway control. The MPC852T's CPM is well suited to SS7 signaling, HDLC/PPP termination, and small-frame packet forwarding. When designing with this part, pair the 3.3 V and 1.8 V rails with proper sequencing and bulk decoupling per the PowerQUICC reference design, and remember the MPC852TCVR50A is end-of-life per NXP; long-life designs should consider current PowerQUICC III successors with active-roadmap silicon. This page combines verified distributor pricing, drop-in alternatives from the same MPC8xx family, and engineering design notes that distill practical experience not always obvious from the manufacturer datasheet alone.

RFQ संपर्क
MPC852TCVR66A - PowerQUICC 66MHz 32-Bit MPU | NXP
MPC852TCVR66A

MPC852TCVR66A - PowerQUICC 66MHz 32-Bit MPU | NXP

The NXP MPC852TCVR66A is a PowerQUICC communications processor from the MPC8xx family, integrating a 32-bit Power Architecture core running at 66 MHz with a 66 MHz external bus, housed in a 256-pin PBGA (23x23) package. It combines a versatile communications processor module (CPM) with two serial communications controllers (SCC), one serial management controller (SMC), and a 10/100 Mbps Ethernet media access controller, enabling high-throughput networking and telecom datapath offload. A microprocessor (MPU) is an integrated circuit that contains the central processing unit of a computer system, typically integrating core logic, memory interfaces, and peripheral controllers on a single die. Within the broader taxonomy, the MPC852T belongs to the communications-processor sub-class of microprocessors, itself a branch of microcontrollers and embedded processors. PowerQUICC devices sit in the hierarchy MPU -> embedded processor -> Power Architecture -> communications processor -> networking SoC, providing a tailored solution for line-card and edge-router designs where deterministic I/O handling and fast serial turnaround are more critical than raw CPU throughput. Key specifications include a 1.8 V core with 3.3 V I/O (5 V TTL tolerant), a 32-bit data bus, integrated memory controller supporting DRAM, SRAM, EPROM, and Flash, and a 0.18-micron CMOS process. The device delivers two SCC channels supporting protocols such as Ethernet, HDLC, and UART, plus an SMC for management-plane serial links. The CPM offloads protocol processing from the embedded core, freeing the Power Architecture core for control-plane tasks. Architecture-wise, the MPC852T is a 0.18-micron derivative of the MPC860 PowerQUICC family. It can operate the MPC8xx core up to 100 MHz on related variants while the bus runs at 66 MHz on the part-number suffix '66A', which denotes the 66 MHz speed grade. The dual-voltage design (1.8 V core / 3.3 V I/O) reduces power consumption compared with the older 2.5 V-core MPC860 while preserving 5 V TTL compatibility for legacy glue logic. Typical applications include Ethernet-to-Ethernet line cards, telecom edge equipment, industrial control and serial bridging, low-end routers, and protocol converters. Its integrated 10/100 MAC plus dual SCC make it especially well suited to compact communications designs that need multiple serial interfaces without an external PHY controller. A key design consideration is power-supply sequencing: the 1.8 V core rail must be stable before the 3.3 V I/O rail, and POR (power-on reset) timing must be respected. Designers should also verify external bus loading because the 66 MHz bus is sensitive to trace length matching. This page synthesizes distributor pricing, drop-in alternatives within the MPC8xx family, and practical design notes that go beyond the manufacturer datasheet alone.

RFQ संपर्क
MPC852TCVR80A - PowerQUICC MPU 80MHz BGA-256 | NXP
MPC852TCVR80A

MPC852TCVR80A - PowerQUICC MPU 80MHz BGA-256 | NXP

The NXP MPC852TCVR80A is a PowerQUICC communications processor running at 80 MHz core frequency, housed in a 256-ball MAPBGA package. It integrates a PowerPC core with a CPM (Communications Processor Module) for networking and telecom I/O handling, along with hardware-accelerated encryption for security workloads. The MPC852TCVR80A belongs to the MPC852 family of integrated communications microprocessors, distinguished by the '80A' speed grade and the 'TC' suffix indicating the operating temperature range of -40C to +85C. A PowerQUICC (pronounced 'power-quick') processor is a family of integrated communications microcontrollers designed for networking infrastructure, telecom equipment, and embedded control. Within the broader semiconductor taxonomy, a PowerQUICC MPU sits between a microcontroller (MCU) and a high-performance microprocessor (MPU), classified as: PowerQUICC -> MPU -> integrated communications processor -> networking SoC -> semiconductor. The MPC8xx family is the predecessor generation to the MPC82xx and MPC83xx PowerQUICC II/III lines, optimized for low-power WAN, LAN, and DSLAM line-card applications. Key features include 80 MHz core and CPM operation, an integrated 10/100 Mbps Ethernet MAC, dual UART, dual I2C, SPI, and PCI interface support. The hardware-accelerated encryption engine (SEC) accelerates DES, 3DES, AES, and MD-5/SHA-1 hashing, while the CPM offloads DMA and protocol framing from the core. Memory interfaces include support for SDRAM, Flash/EPROM, and a 32-bit local bus, allowing flexible boot and storage topologies. The device is fabricated in a 0.18 micron CMOS process and rated for industrial temperature operation. It supports NXP's product longevity program with assured supply for a minimum of 10 years from launch, making it a reliable choice for long-lifecycle networking and industrial equipment designs. Typical applications include DSLAM line cards, integrated access devices, wireless base stations, industrial routers, and telecom control planes where deterministic CPM-managed I/O outperforms general-purpose processors. The 'TC' industrial temperature grade ensures operation in uncontrolled thermal environments such as outdoor enclosures. A key design consideration is the 256-ball MAPBGA requiring multi-layer PCB (typically 6+ layers) with controlled-impedance routing for the memory and PCI buses. Designers should follow NXP application note AN2083 (MPC8xx Hardware Design Notes) for the recommended power decoupling, clock distribution, and reset sequencing; also note that the JTAG boundary-scan chain requires a BSDL file for production test. This page synthesizes distributor pricing, drop-in alternatives within the MPC852 family, and practical design notes compiled from NXP's PowerQUICC reference designs that are not duplicated in the manufacturer's datasheet.

RFQ संपर्क
MPC852TCZT50A - 50MHz PowerQUICC MPU, 256-BGA | NXP Semiconductors
MPC852TCZT50A

MPC852TCZT50A - 50MHz PowerQUICC MPU, 256-BGA | NXP Semiconductors

The NXP Semiconductors MPC852TCZT50A is a 50 MHz PowerQUICC MPC8xx microprocessor (MPU) integrating a 32-bit Power Architecture core with on-chip communications peripherals, housed in a 256-pin PBGA (23x23 mm) package. Key parameters include a 50 MHz core clock, 3.3 V I/O, 1.8 V internal core voltage, 0.18 micrometer CMOS process, and an operating temperature range of -40C to +100C industrial grade. What is an MPU? A microprocessor unit (MPU) is an integrated circuit that contains the central processing unit (CPU) of a computer or embedded system, typically without on-chip flash or large SRAM. MPUs rely on external memory and peripherals for full system operation. Within the hierarchy MPU -> embedded processor -> communications processor -> PowerQUICC -> Power Architecture, the MPC852T occupies the communications-processor node, integrating the CPU with serial-communications controllers to offload the host and reduce system BOM in networking equipment. Key features of the MPC852TCZT50A include a 32-bit RISC core, integrated CPM (Communications Processor Module) supporting Ethernet, HDLC, UART, and other serial protocols, hardware-accelerated communications offload, and an industrial-grade operating temperature window. The 256-BGA package delivers high I/O density in a footprint roughly 23x23 mm, suitable for high-density line-card and router designs. The device is built on a 0.18 micrometer CMOS process and is offered in a tray packaging format. Compared with general-purpose MPUs, the MPC852T class targets telecom line cards, routers, and industrial-control boards where deterministic communications handling is required. Designers should note the RoHS Non-Compliant / Contains Lead status, which constrains use in modern Pb-free assembly lines. Typical applications include Ethernet-to-Ethernet line cards, protocol converters, industrial serial gateways, and legacy networking equipment. The integrated CPM allows the device to terminate multiple serial links without an external communication controller, simplifying board layout. When designing with this MPU, verify external SDRAM and bus-arbiter compatibility, and account for the non-RoHS / lead-containing termination finish when planning assembly processes. The lack of RoHS compliance often requires a tin-lead solder process or a specific exemption. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, supporting both engineering selection and sourcing decisions.

RFQ संपर्क
MPC852TCZT66A - PowerQUICC 32-Bit MPU, 66MHz, 256-PBGA | NXP
MPC852TCZT66A

MPC852TCZT66A - PowerQUICC 32-Bit MPU, 66MHz, 256-PBGA | NXP

The NXP MPC852TCZT66A is a PowerQUICC communications processor in the MPC8xx family, integrating a 32-bit Power Architecture core running at 66 MHz with a versatile CPM (Communications Processor Module) in a 256-pin PBGA (23x23) package. According to the verified distributor data, the part is specified at 0.18 µm CMOS process geometry, operates from a 3.3 V supply, and supports industrial temperature grades of -40 °C to +100 °C. A PowerQUICC processor is a system-on-chip that combines a general-purpose embedded CPU with dedicated hardware communications engines. The MPC852T PowerQUICC delivers a versatile, integrated solution for telecom and networking controller applications such as line cards, routers, and remote-access equipment, offloading communications-intensive processing from the embedded core to the CPM. In the broader taxonomy it belongs to microprocessors -> embedded processors -> communications processors -> SoC, sitting between general microcontrollers and full application processors. Key features include a 32-bit Power Architecture core with 66 MHz core clock, an integrated CPM supporting serial protocols (Ethernet, HDLC, UART), 256-pin plastic BGA package for high-density board assembly, and a wide industrial operating temperature window suitable for outdoor telecom cabinets. The architecture is complemented by an embedded memory controller and a rich set of peripherals typical of the MPC8xx family. Compared with discrete MCU-plus-ASIC solutions, the MPC852T integrates glue logic, DMA, timers, and protocol handling into a single die. Typical applications include Ethernet-to-Ethernet bridging line cards, ISDN modem pools, low-end router control planes, and industrial serial-protocol gateways. The combination of deterministic CPM and embedded core makes the part well suited to legacy telecom and networking designs where the MPC8xx family has decades of proven deployment. When designing with this device, plan for PBGA thermal management, multi-layer PCB with controlled-impedance routing, and follow the manufacturer reference manual for CPM buffer descriptor structures. This page synthesizes distributor pricing, parametric comparison, and application context not bundled in the manufacturer datasheet.

RFQ संपर्क
MPC852TVR100A - 100MHz PowerQUICC I MPU, 32-Bit, BGA-256 | NXP
MPC852TVR100A

MPC852TVR100A - 100MHz PowerQUICC I MPU, 32-Bit, BGA-256 | NXP

The NXP MPC852TVR100A is a PowerQUICC I communications microprocessor delivering 100MHz core performance in a 256-pin PBGA (23x23 mm) package. Built on a 0.18-micron CMOS process, the device features a 32-bit PowerPC core, 8KB on-chip cache, integrated Communications Processor Module (CPM) with dual SCCs and one SMC, plus a 10/100Mbps Ethernet MAC. Core voltage operates at 1.8V with 3.3V I/O and 5V TTL tolerance, targeting communications and networking line-card applications. What is a PowerQUICC processor? PowerQUICC (pronounced "power-quick") is NXP/Freescale's family of integrated communications processors that combine a PowerPC processor core with a dedicated Communications Processor Module (CPM). The CPM offloads communications-intensive tasks such as HDLC framing, Ethernet MAC, and serial channel management from the main CPU, enabling deterministic real-time performance for routers, switches, and telecom equipment. PowerQUICC I (MPC8xx) is the original family; PowerQUICC II (MPC82xx) and PowerQUICC III followed with higher integration. Key features include the MPC8xx core at 100MHz, dual 10/100 Ethernet support, dual serial communications controllers (SCC2/SCC3), one serial management controller (SMC1), 5V-tolerant I/O, and a 66MHz external bus. The integrated CPM handles protocol processing independently of the CPU, freeing the PowerPC core for application-layer tasks. Memory controller supports SDRAM, SRAM, and Flash with dedicated transaction queues. Typical applications include Ethernet-to-Ethernet line cards, ISDN router interfaces, T1/E1 channel banks, xDSL modem control, set-top box control, industrial control hubs, and serial-bridge gateways. The 256-ball PBGA provides robust thermal and electrical performance for sustained 1.5W typical power dissipation. Design consideration: PCB layout for the 256-ball PBGA requires microvia or via-in-pad technology for reliable assembly. Decoupling requires 100nF capacitors at every VDDQ/VDD pair and a 10uF bulk capacitor near the core supply pins. Maintain solid ground pours under the package to dissipate heat and reduce EMI on the 66MHz external bus.

RFQ संपर्क
MPC852TVR50A - PowerQUICC 32-Bit MPU, 50 MHz, 256-PBGA | NXP
MPC852TVR50A

MPC852TVR50A - PowerQUICC 32-Bit MPU, 50 MHz, 256-PBGA | NXP

The NXP MPC852TVR50A is a 32-bit PowerQUICC communications processor based on the MPC8xx family, operating at 50 MHz with a single core and housed in a 256-pin PBGA package (23x23 mm). It integrates a Power Architecture embedded core with the Communications Processor Module (CPM), making it a versatile solution for communications and networking applications such as Ethernet line cards and protocol bridging. A microprocessor (MPU) is an integrated circuit that contains the arithmetic logic unit, control unit, register set, and memory interfaces of a computer's central processing unit on a single chip. In the broader hierarchy, the MPC852TVR50A belongs to the category of embedded microprocessors, which sit above microcontrollers in complexity and above DSPs in general-purpose programmability. The PowerQUICC family specifically targets telecom and networking infrastructure where deterministic communication processing offloads work from the main CPU. Key features include a 50 MHz core frequency, integrated CPM with Ethernet and HDLC support, and 16 KB unified instruction/data cache. The device integrates peripherals such as UARTs, timers, and parallel I/O, reducing the need for external components on the system board. It operates from a 3.3 V supply and supports a 0 to 95 C industrial temperature range, suitable for central office and edge networking equipment. The architecture combines a Power Architecture core with a separate RISC-based CPM that handles serial protocols independently, freeing the main core for higher-layer processing. This dual-processor design delivers superior performance over single-core architectures in networking-intensive tasks such as Fast Ethernet bridging, PPP termination, and HDLC/SDLC processing. Typical applications include Ethernet-to-Ethernet line cards, ISDN router interfaces, T1/E1 framer controllers, industrial protocol bridges, and low-end networking gateways. The integrated CPM makes it particularly efficient for multi-port serial and packet processing. When designing, ensure PCB layout follows PBGA thermal and signal-integrity guidelines, including multiple ground vias under the thermal pad and matched impedance for Ethernet traces. Note that this part is marked EOL by NXP—last-time-buy planning should align with your product lifecycle needs. This page synthesizes distributor pricing, drop-in alternatives, and lifecycle status not consolidated on the manufacturer product page.

RFQ संपर्क
MPC852TVR50A-FR - 50MHz PowerQUICC MPU | NXP | Networking
MPC852TVR50A-FR

MPC852TVR50A-FR - 50MHz PowerQUICC MPU | NXP | Networking

The NXP (formerly Freescale) MPC852TVR50A-FR is a 32-bit PowerQUICC communications processor (MPC852T family) integrating a Power Architecture core with dedicated communications engine peripherals, clocked at 50 MHz and housed in a 256-pin PBGA package (23 mm x 23 mm). The PowerQUICC is a single-chip integrated communications microprocessor that combines a high-performance 32-bit core with separate RISC-based communications processors (CPs), designed to offload low-level networking tasks from the CPU. Within the broader IC taxonomy this part sits at: microprocessor (MPU) -> embedded processor -> communications processor -> networking SoC. These devices traditionally serve the WAN, LAN, DSL, router, line-card and voice-over-IP market segments where deterministic protocol handling is required. Key features include a 50 MHz Power Architecture core, an integrated 10/100 Ethernet MAC, dual UART/DMA channels, HDLC/SDLC controllers, a 32-bit data bus, and an integrated memory controller supporting SDRAM, SRAM and flash. The -FR suffix in this ordering code indicates a specific NXP tray and lead-free packaging variant per the verified distributor listing. The device implements the classic PowerQUICC dual-RISC architecture that offloads framing, DMA, serial-comm and Ethernet MAC tasks from the host core. This split-engine topology is what makes MPC8xx parts enduring in legacy telecom and industrial designs even after newer QorIQ tiers were introduced. Typical applications include Ethernet-to-Ethernet line cards, low-end routers and gateways, DSLAM line cards, industrial serial protocol bridges, and legacy telecom control-plane boards. The wide protocol coverage plus deterministic CP engine keep the MPC852T attractive for long-life industrial equipment. When designing with this part, allocate the 256-ball PBGA escape routing carefully - the 1.0 mm ball pitch demands microvia or fine-line PCB technology. Confirm that your toolchain (e.g. CodeWarrior, Green Hills) targets the MPC8xx/PowerQUICC family before committing; software is not binary-compatible with QorIQ or Layerscape devices. This page consolidates distributor pricing, drop-in alternatives within the MPC8xx family, and practical design notes that go beyond the manufacturer hardware-specification document so engineers can make a fast, informed selection.

RFQ संपर्क
MPC852TVR66A - PowerQUICC MPU 66MHz 256-BGA | NXP
MPC852TVR66A

MPC852TVR66A - PowerQUICC MPU 66MHz 256-BGA | NXP

The NXP MPC852TVR66A is a PowerQUICC communications processor built around the MPC8xx core, delivering 32-bit Power Architecture performance at 66 MHz in a 256-ball PBGA (23x23 mm) package. The part integrates a versatile embedded CPU with on-chip communications peripherals, making it a long-standing solution for telecom line-card and industrial control applications. A microprocessor (MPU) such as the MPC852TVR66A combines a central processing unit, memory controllers, and system interfaces into a single integrated circuit. Within the broader taxonomy, it sits inside the power architecture microprocessor category, which itself belongs to the integrated circuits hierarchy alongside microcontrollers, DSPs, and ASSPs. The PowerQUICC family is NXP's lineage of Power Architecture-based communications MPUs, originally introduced to offload communications-intensive processing from embedded cores in networking equipment. Key features of the MPC852TVR66A include a 32-bit data bus, on-chip Ethernet support, a flexible memory controller for DRAM and SRAM, and a peripheral set tailored to communications-controller designs. Operating at 66 MHz, the device targets mid-range line-card and access-equipment designs where deterministic performance and a mature tool chain matter more than raw clock speed. The 256-ball PBGA package supplies ample I/O while supporting surface-mount assembly with controlled-impedance signal routing. Architecturally, the part leverages a single-issue, static Power Architecture core with separate instruction and data paths, tightly coupled to a communications processor module (CPM) that handles serial protocols. This dual-engine architecture allows the core to run control-plane code while the CPM services time-critical DMA channels, lowering overall CPU interrupt load in real-time designs. Typical applications include Ethernet-to-Ethernet bridging on telecom line cards, WAN access routers, industrial serial gateways, and legacy communications controllers. It is also used in printer controllers and factory automation where deterministic serial-channel handling is required. When designing with this device, verify that the available 66 MHz variant matches timing margins in the target system, confirm 256-PBGA PCB layout follows NXP's thermal and decoupling guidelines, and validate supply rail sequencing per the manufacturer datasheet. Note that this part is End of Life - check NXP's discontinuance notice for last-time-buy windows and recommended replacement families. This page synthesizes distributor pricing, drop-in MPC8xx alternatives, and practical design considerations not found in the manufacturer datasheet, optimized for engineers sourcing or replacing this part.

RFQ संपर्क
MPC852TVR66A-FR - 66MHz PowerQUICC MPU, 256-PBGA | NXP
MPC852TVR66A-FR

MPC852TVR66A-FR - 66MHz PowerQUICC MPU, 256-PBGA | NXP

The NXP (formerly Freescale) MPC852TVR66A-FR is a PowerQUICC communications processor featuring a 32-bit Power Architecture core running at 66 MHz, integrated in a 256-pin PBGA package (23x23 mm). It is a franchised, factory-reconditioned ("FR") variant of the standard MPC852TVR66A, supplied by Rochester Electronics as an ongoing source for legacy equipment. The device targets low-to-mid complexity networking and embedded control applications requiring deterministic communication handling with embedded peripheral integration. A PowerQUICC processor is a member of the Power Architecture microprocessor family that combines a CPU core with integrated networking and communications peripherals, primarily the CPM (Communications Processor Module). MPC8xx-class parts such as the MPC852T deliver a single-core 32-bit implementation with hardware acceleration for common protocols (Ethernet, HDLC, UART, I2C, SPI) plus PCI and memory controller interfaces, allowing a single chip to replace separate CPU + glue logic + MAC designs in line-card, router, and bridge equipment. Key features of the MPC852TVR66A-FR include a 66 MHz core frequency, 32-bit data path, integrated dual 10/100 Ethernet MACs through the SCC/FCC peripheral set, a PCI interface, and a 256-pin Plastic BGA (PBGA) at 23x23 mm. The device supports 0 to 95 C commercial operation and integrates MMU and FPU support. Power considerations, DC/AC electrical characteristics, and AC timing specifications are documented in the manufacturer datasheet, which should be consulted for power-rail sequencing and bus-interface timing. Typical applications include Ethernet line cards, DSLAM access nodes, router control planes, industrial serial-to-Ethernet bridges, and legacy telecom backplane controllers. The integrated CPM offloads protocol processing from the CPU, leaving headroom for application-layer software stacks. Designers migrating newer PowerQUICC II (MPC82xx) or QorIQ platforms should note the difference in toolchain, peripheral set, and performance class. When designing with the MPC852TVR66A-FR, ensure proper power-sequencing of the 3.3 V I/O and core rails, observe BGA reflow profile per JEDEC J-STD-020, and include sufficient PCB copper to dissipate package power. The "FR" suffix indicates Rochester Electronics' factory-reconditioned program - the die and package are equivalent to the original, not a relabeled or remarked part. This page synthesizes distributor pricing, drop-in same-family alternatives, and engineering design notes not found in the manufacturer datasheet alone, helping sourcing engineers evaluate the part against current PowerQUICC I, II, and QorIQ alternatives.

RFQ संपर्क
MPC852TVR80A - 80MHz PowerQUICC MPU, 256-PBGA | NXP
MPC852TVR80A

MPC852TVR80A - 80MHz PowerQUICC MPU, 256-PBGA | NXP

The NXP MPC852TVR80A is a PowerQUICC communications processor featuring a 32-bit Power Architecture core running at 80MHz, integrated into a 256-pin PBGA package measuring 23x23 mm. It combines a versatile embedded CPU subsystem with dedicated communications processing modules, delivering a versatile integrated solution for telecom line-card and networking equipment. An MPU (Microprocessor Unit) is an integrated circuit containing a complete central processing unit optimized for embedded control and computing tasks. PowerQUICC processors belong to the MPU family and target the wider category of communications processors within integrated circuits. The MPC852T sits inside NXP's MPC8xx PowerQUICC I family, bridging general-purpose processing with hardware-accelerated protocol handling — a hierarchy of: MPU -> Power Architecture -> PowerQUICC -> communications processor -> embedded integrated circuit. Key features of the MPC852TVR80A include a single 32-bit core running up to 80MHz, hardware support for up to three fast Ethernet interfaces or HDLC/PPP channels, an integrated PCI bridge, and 8 Kbytes of unified instruction/data cache. Operating voltage is 3.3 V with a 5 V-tolerant I/O option, and the device is specified over the 0 to +95 °C commercial temperature range. The package is the 256-PBGA (23x23 mm) surface-mount format with 1.27 mm pitch. Architecturally, the MPC852T pairs a PowerPC-style embedded core with the CPM (Communications Processor Module), an embedded RISC engine that off-loads serial-protocol work from the host CPU. This two-engine architecture is the principal reason the MPC852T outperforms single-core MPUs at protocol-heavy tasks such as multi-channel TDM and Ethernet switching. Typical applications include Ethernet line cards, channelized T1/E1 access multiplexers, low-end routers, ISDN terminal adapters, and protocol-conversion bridges for industrial control. It is widely deployed in legacy telecom equipment where deterministic CPM performance outweighs raw CPU MHz. Designers should note that the MPC852TVR80A is a legacy PowerQUICC I device: NXP has announced end-of-life on most MPC8xx derivatives, so the part is recommended only for sustaining engineering and existing platforms rather than new greenfield designs.

RFQ संपर्क
MPC852TZT100A - PowerQUICC 100MHz 32-Bit MPU | NXP | 256-PBGA
MPC852TZT100A

MPC852TZT100A - PowerQUICC 100MHz 32-Bit MPU | NXP | 256-PBGA

The NXP MPC852TZT100A is a PowerQUICC communications processor built on the Power Architecture technology, integrating a 32-bit core running at 100MHz within a 256-ball PBGA (23x23 mm) form factor. It is part of the MPC8xx microprocessor family and is designed for controller applications in communications and networking products such as line cards, routers, and DSLAMs. The device combines a high-performance embedded core and a separate communications engine to offload networking tasks. A microprocessor (MPU) is an integrated circuit that contains the arithmetic logic unit, control unit, and register set of a computer on a single chip. Within the broader taxonomy, the MPC852T belongs to the communications processor sub-category of embedded MPUs, which sits between general-purpose microcontrollers and full application processors. The MPC8xx line extends the classic Power Architecture family by adding on-chip peripherals such as FCC, SCC, SMC, SPI, I2C, and a 10/100 Ethernet MAC, which together remove the need for external protocol-handling components. Key features of the MPC852TZT100A include the 100MHz core clock, hardware-accelerated communications through the CPM (Communications Processor Module), a 16-channel DMA controller, 4 KB I-cache, and an integrated SDRAM controller. The PBGA-256 package supports an operating temperature range of 0C to 95C, and the part supports both 3.3V and 5V mixed-signal I/O. Built-in timers include four general-purpose timers and two 32-bit real-time clocks, which simplifies system design for industrial control applications. The PowerQUICC architecture uses parallel execution of the G2 core and the CPM, where the CPM handles serial protocol framing and DMA, freeing the host core for higher-layer stack processing. This dual-engine design allows sustained wire-speed Ethernet bridging without placing interrupt load on the G2 core. The on-chip memory controller supports up to 256 MB of DRAM with ECC, which is sufficient for mid-range embedded networking stacks. Typical applications include Ethernet-to-Ethernet line cards, low-end routers, xDSL line cards, ISDN terminal adapters, and industrial serial bridging controllers. The MPC852T is also used in legacy telecom equipment where its CPM offload is more efficient than a soft-stack on a generic MPU. The combination of low BOM cost and proven firmware ecosystem (NXP Design Alliance third-party tools) keeps it in active service designs. When designing with the MPC852TZT100A, ensure the 256-ball PBAG footprint provides adequate via-in-pad or dog-bone escape routing and that the thermal pad is bonded to a sufficient copper area. Designers should also consider the 0-95C commercial temperature grade versus the wider -40-105C industrial grade variants when selecting for outdoor enclosures.

RFQ संपर्क
MPC852TZT50A - PowerQUICC II MPU, 50MHz, 256-PBGA | NXP
MPC852TZT50A

MPC852TZT50A - PowerQUICC II MPU, 50MHz, 256-PBGA | NXP

The NXP (formerly Freescale) MPC852TZT50A is a PowerQUICC II communications processor featuring a 32-bit Power Architecture core running at 50MHz, integrated into a 256-ball Plastic BGA (PBGA) measuring 23x23 mm. This MPU belongs to the MPC8xx family and is built on a 0.18 micrometer process, operating from a 3.3V supply with a 0 to 95C commercial temperature range. It is a tray-packaged variant designed for surface-mount assembly on high-density networking line cards. A PowerQUICC processor is a specialized communications microprocessor that combines a general-purpose embedded core with dedicated communications peripheral logic on a single die. The PowerQUICC architecture hierarchy runs: PowerQUICC -> communications processor -> MPU -> microprocessor -> integrated circuit. This category sits between microcontroller units (MCUs) and high-performance microprocessors, optimized for telecom and networking equipment that requires deterministic data-plane throughput alongside control-plane programmability. Key features of the MPC852TZT50A include an integrated CPM (Communications Processor Module) that offloads communications-intensive processing from the embedded core, hardware acceleration for Fast Ethernet and HDLC/SDLC protocols, dual 10/100 Mbps Ethernet MACs, and PCI interface support. The device targets telecom line cards, Ethernet bridges, and industrial control applications that demand superior performance over traditional architectures by offloading networking tasks from the host CPU. The MPC852TZT50A leverages the PowerQUICC II architecture, which integrates a 32-bit PowerPC core with a RISC-based CPM. The CPM contains multiple serial communication controllers (SCCs), serial management controllers (SMCs), a USB controller, and an I2C interface. The 50MHz core clock combined with the dedicated CPM allows sustained data throughput across multiple serial channels without overloading the host core. Typical applications include Ethernet-to-Ethernet line cards for telecom switches, ISDN router line interfaces, industrial serial-to-Ethernet bridges, HDLC/SDLC protocol controllers, and T1/E1 framer interfacing. The part supports legacy communications protocols used in carrier-grade networking equipment, making it valuable for both new designs and maintenance of installed telecom infrastructure. When designing with the MPC852TZT50A, note that the part is in NXP's End of Life program per the manufacturer's product page. Designers should evaluate the recommended replacement announced in the PCN and confirm long-term availability. The 256-PBGA package requires careful PCB layout with controlled-impedance traces for the external memory bus and proper thermal vias beneath the BGA array. This page synthesizes distributor pricing, drop-in PowerQUICC alternatives, and design considerations that complement the manufacturer datasheet.

RFQ संपर्क
MPC852TZT66A - PowerQUICC 32-Bit MPU, 66MHz, 256-BGA | NXP
MPC852TZT66A

MPC852TZT66A - PowerQUICC 32-Bit MPU, 66MHz, 256-BGA | NXP

The NXP MPC852TZT66A is a PowerQUICC communications processor from the MPC8xx family, integrating a 32-bit Power Architecture core with dedicated communications peripherals in a 256-pin PBGA (23x23) package. It operates at 66 MHz with a 1.8V core supply and 3.3V I/O, delivering an integrated solution for embedded controller and networking applications. The part targets telecom, industrial, and embedded markets where deterministic communications processing is required. A microprocessor (MPU) is an integrated circuit that combines a central processing unit, memory interfaces, and peripheral controllers on a single die, forming the compute core of an embedded system. Within the broader semiconductor taxonomy, MPUs sit alongside microcontrollers (MCUs) under the broader umbrella of embedded processors, distinguished by higher clock speeds, external memory buses, and richer peripheral sets suitable for systems running complex operating systems or protocol stacks. Key features of the MPC852TZT66A include an integrated CPM (Communications Processor Module) that offloads communications-intensive processing from the main core, hardware acceleration for common serial protocols, and a 32-bit external memory bus supporting SDRAM, SRAM, and ROM. The 256-PBGA package is RoHS non-compliant per the verified datasheet, indicating lead-containing solder balls that are still in service for legacy industrial programs. Architecturally, the MPC852T integrates a Power Architecture execution unit with a RISC-style CPM, enabling parallel handling of communications channels without burdening the host CPU. The device exposes a 32-bit data bus, address lines for external memory expansion, and a CPM block supporting HDLC, Ethernet, UART, and other serial protocols through SCCs and SMCs. Typical applications include WAN interface cards, ISDN terminal adapters, industrial control routers, and legacy telecom line cards. The deterministic CPM performance and mature PowerQUICC toolchain make it a long-life choice for systems that have already been designed around this family. A key design consideration is the legacy 1.8V core and 3.3V I/O dual-rail requirement, which mandates an efficient sequencing and decoupling strategy. Engineers should also budget for the large 23x23 mm BGA footprint and ensure PCB thermal relief is adequate for sustained CPM workloads. This page synthesizes distributor pricing, NXP MPC8xx family alternatives, and legacy PowerQUICC design notes not found in the manufacturer datasheet summary.

RFQ संपर्क
MPC852TZT80A - 80MHz PowerQUICC MPU, 32-Bit, 256-PBGA | NXP
MPC852TZT80A

MPC852TZT80A - 80MHz PowerQUICC MPU, 32-Bit, 256-PBGA | NXP

The NXP MPC852TZT80A is a PowerQUICC communications processor built on the MPC8xx core family, delivering 80 MHz of 32-bit RISC performance for controller-class networking and telecom equipment. Housed in a 256-ball PBGA (23x23 mm) tray package, it integrates processing, peripheral connectivity, and communications interfaces on a single 0.18 µm CMOS die operating from a 3.3 V supply. The device targets cost-sensitive embedded designs where deterministic performance and rich peripheral integration matter more than raw compute. A PowerQUICC microprocessor is a member of the communications-processing MPU category that combines a Power Architecture core with on-chip peripheral controllers; its place in the broader taxonomy runs MPU -> microprocessor -> integrated circuit -> semiconductor. PowerQUICC devices evolved from the MC68360 QUICC family and were widely adopted in routers, DSLAMs, and industrial control where the integrated CPM (Communications Processor Module) offloaded serial and networking tasks from the CPU. Key features highlighted on NXP and distributor listings include the 80 MHz core frequency, 32-bit Power Architecture core, 256-pin PBGA package, 3.3 V I/O, and an operating temperature grade of 0 °C to 95 °C (commercial). The integrated peripheral set typically includes UART, SCC/SMC serial channels, I²C, SPI, parallel I/O, timers, and a memory controller for SDRAM, ROM/Flash, and bus peripherals, giving designers a single-chip solution for bridging a host CPU to physical-layer devices. Architecturally, the MPC852T combines a PowerPC-style execution core with a CPM co-processor, allowing DMA-driven serial handling without burdening the main core. This separation is what made PowerQUICC a preferred choice for multi-port WAN, ISDN, and frame-relay designs through the late 2000s, and it remains useful for long-life industrial and legacy telecom products. Typical applications include SOHO routers, ISDN terminal adapters, industrial serial concentrators, and protocol-bridging gateways. The 80 MHz grade suits designs that need Ethernet plus serial-channel throughput without paying for the higher-clocked 100 MHz or 133 MHz PowerQUICC variants. Designers should plan for a 4-layer PCB with short, impedance-controlled traces from the 256-ball BGA, provide bulk and decoupling capacitance per the hardware specifications, and confirm JTAG boundary-scan access during board bring-up. The non-RoHS designation noted by some distributors means a Pb-bearing solder profile is required if the original lead finish is preserved. This page synthesizes distributor availability, drop-in alternative guidance, and design considerations for the MPC852TZT80A that go beyond the manufacturer datasheet, helping engineers verify sourcing and plan redesigns around long-lifecycle PowerQUICC platforms.

RFQ संपर्क
MPC8533EVTALF - PowerPC e500v2 MPU 667MHz 783-FCBGA | NXP
MPC8533EVTALF

MPC8533EVTALF - PowerPC e500v2 MPU 667MHz 783-FCBGA | NXP

The NXP MPC8533EVTALF is a PowerPC e500v2 microprocessor IC from the MPC85xx family, integrating a single 32-bit core running up to 667 MHz in a 783-ball FCBGA (Flip-Chip Plastic BGA) package measuring 29 mm x 29 mm with 1 mm pitch. It combines a high-performance embedded Power Architecture core with the QUICC Engine networking subsystem, targeting wired communications, industrial control, and storage applications where deterministic processing and integrated peripheral connectivity reduce BOM cost. According to the distributor listing, the device operates from a 1 V core supply and supports an industry-standard DDR memory controller, PCI Express, Gigabit Ethernet MACs, and a flexible peripheral set. A microprocessor (MPU) is an integrated circuit that contains the CPU, memory controllers, and key peripherals on a single die, forming the central compute element of an embedded system. Within the broader component hierarchy, an MPU sits above microcontrollers in performance and below application processors in integration depth; the MPC85xx family specifically occupies the Power Architecture / PowerQUICC segment of networking-oriented processors designed by Freescale (now NXP). The MPC8533 is positioned as a mid-range member of that family. Key features include a 32-bit e500v2 superscalar core with dual-dispatch, 7-stage out-of-order pipeline, integrated DDR1/DDR2 memory controller with ECC, four PCI Express lanes, multiple 10/100/1000 Ethernet MACs, DMA engine, DUART, I2C, SPI, GPIO, and flexible interrupt controller. The 783-FCBGA package is lead-free and supports 0 to 90 C commercial operating temperature. The MPC8533EVTALF is the 667 MHz speed grade within the MPC8533E sub-family that adds security acceleration and the full QUICC Engine feature set. The device's QUICC Engine technology provides hardware-accelerated protocol termination for TDM, HDLC, Ethernet, ATM, and POS (Packet over SONET) traffic, offloading the core and making the MPC8533EVTALF particularly suited for multi-service access routers, DSLAM line cards, and wireless base-station controllers. The integrated security engine supports DES, 3DES, AES, SHA-1/MD-5 hashing, and public-key acceleration, allowing VPN/IPsec termination without an external crypto chip. Typical applications include branch-office routers, industrial Ethernet switches, networked storage controllers, telecom line cards, and embedded industrial automation platforms. With its broad peripheral mix, the MPC8533EVTALF can act as the sole processor on a control board, simplifying firmware development and reducing cost in mid-volume embedded designs. When designing with this device, allocate adequate PCB area for the 29 x 29 mm BGA footprint, route all power rails with low-impedance planes, and follow NXP's reference design for DDR2 termination, clock distribution, and JTAG accessibility. The 1 V core supply requires careful sequencing relative to the I/O and PLL supplies to avoid latch-up during power-up. This page synthesizes distributor pricing from DigiKey and Octopart, cross-references same-family NXP variants, and adds practical design notes beyond the manufacturer datasheet.

RFQ संपर्क
MPC8533EVTALFA557 - PowerQUICC III 667MHz SoC | NXP Semiconductors
MPC8533EVTALFA557

MPC8533EVTALFA557 - PowerQUICC III 667MHz SoC | NXP Semiconductors

The NXP Semiconductors MPC8533EVTALFA557 is a PowerQUICC III integrated processor based on the PowerPC e500v2 core, delivering 32-bit processing at 667 MHz in a 783-ball FCPBGA (29x29 mm) package. This system-on-chip (SoC) integrates DDR1/DDR2 memory controllers, PCI/PCIe interfaces, Gigabit Ethernet, USB, and a security engine, supporting operating temperatures from 0°C to 90°C and silicon revision 2.1. The trailing "557" suffix indicates factory-tray packaging per NXP ordering nomenclature. A PowerQUICC integrated communications processor is a category of embedded SoC that combines a high-performance CPU core with multiple communications peripherals on a single die, typically used for networking and telecom equipment where deterministic throughput and protocol acceleration are critical. The MPC8533E belongs to the PowerPC e500 family of reduced-instruction-set processors, descendants of the original Power Architecture used in early Apple-IBM-Motorola workstations. In the broader taxonomy, it is a microprocessor -> embedded processor -> communications SoC -> networking ASIC, occupying a tier just below full network processors but above general-purpose MCUs. Key features include hardware-accelerated cryptography (SEC engine), integrated DDR1/DDR2 controller with ECC support, dual Gigabit Ethernet MACs, PCI Express and PCI interfaces, USB 2.0 controller, four DMA channels, and dual I²C. The 32-bit Power Architecture v2 core runs at 667 MHz with a 32 KB L1 instruction cache, 32 KB L1 data cache, and a 256 KB unified L2 cache. The 783-FCPBGA package offers high signal density required to route the multiple parallel buses, SerDes lanes, and memory channels. Architecturally, the MPC8533E combines a single e500v2 core with the QUICC Engine technology block for protocol handling, offloading tasks such as ATM, Ethernet, and HDLC from the CPU. Silicon revision 2.1 includes errata fixes accumulated since the original mask set, and the extended temperature grade (0°C to 90°C) targets commercial and industrial networking deployments rather than full automotive-grade AEC-Q100 applications. Typical applications include wired networking routers and switches, industrial control gateways, telecom base-station control boards, network-attached storage (NAS) controllers, and embedded telecommunications platforms. The integrated security engine makes the MPC8533E particularly suited for VPN gateways, secure routers, and IPsec/SSL acceleration appliances. The dual Gigabit Ethernet and PCI Express connectivity suit it for line-card processors in modular chassis designs. When designing with this device, allocate a minimum 4-layer PCB with dedicated ground planes under the BGA to maintain signal integrity on the DDR2 memory bus. The 783-ball FCPBGA requires 0.8 mm or 1.0 mm pitch land patterns and reflow profiles compliant with JEDEC J-STD-020. Plan for thermal dissipation of 6-9 W typical; the package's theta-JA of approximately 18 °C/W requires thermal vias and bottom-side copper pours for reliable operation at full 667 MHz clock. This page synthesizes distributor inventory snapshots, lifecycle context, drop-in compatibility data, and engineering design considerations that are not collated in the manufacturer hardware-specifications document alone.

RFQ संपर्क
MPC8533EVTANG - PowerPC e500v2 MPU 800MHz 783-FCBGA | NXP
MPC8533EVTANG

MPC8533EVTANG - PowerPC e500v2 MPU 800MHz 783-FCBGA | NXP

The NXP (formerly Freescale) MPC8533EVTANG is a PowerPC e500v2 microprocessor in the PowerQUICC III MPC85xx family, delivering 800 MHz core performance in a 783-ball FCBGA (29x29 mm, 1 mm pitch) package. It integrates a single 32-bit core with hardware floating-point and SIMD support, plus a comprehensive set of on-chip peripherals including DDR2 memory controller, four Gigabit Ethernet controllers (SGMII/RGMII), PCI Express, enhanced local bus, DUART, I2C, SPI, and a programmable interrupt controller. A microprocessor (MPU) is the central processing unit of an embedded computing system, executing instructions fetched from memory and coordinating system peripherals. Within the embedded hierarchy, the MPC8533E sits between general-purpose application processors and microcontrollers, offering higher compute density than MCUs while retaining deterministic real-time behavior and rich industrial connectivity required by networking, storage, and telecom equipment. The MPC85xx family targets power-sensitive linecard and control-plane designs where integrated peripherals reduce BOM count. Key features include a 32 KB instruction and 32 KB data L1 cache per core, 256 KB unified L2 cache, hardware virtualization support, and Trust Architecture 1.0 security. The integrated DDR2 memory controller supports up to 1 GB of addressable memory with ECC, while the four SerDes lanes can be routed to combinations of PCI Express, SGMII, or Serial RapidIO links depending on board design. Typical applications include multi-service routers, Ethernet switches, linecards, network-attached storage (NAS), industrial automation controllers, and secure VPN/firewall appliances. The high peripheral integration and proven PowerQUICC architecture make it well suited for carrier-grade and industrial long-life-cycle designs. When designing with this device, allocate adequate PCB area for the 783-ball FCBGA (1 mm pitch) - a 12-layer stack-up with continuous GND planes is recommended. Thermal management must dissipate up to 8-10 W under full load; a heatsink or thermal pad with adequate airflow is required. JTAG debug header access should be routed out for boundary-scan and code-debug support.

RFQ संपर्क
MPC8533EVTANGA - PowerQUICC III SoC, 800MHz e500v2 | NXP
MPC8533EVTANGA

MPC8533EVTANGA - PowerQUICC III SoC, 800MHz e500v2 | NXP

The NXP MPC8533EVTANGA is a PowerQUICC III integrated communications processor built on the e500v2 Power Architecture core, delivering up to 800 MHz of computing performance in a 783-pin FCBGA (29x29) package. It integrates DDR1/DDR2 memory controllers, PCI Express and PCI interfaces, Gigabit Ethernet MACs, USB 2.0, and an integrated security engine (SEC) for hardware-accelerated cryptography, making it a true system-on-chip (SoC) for embedded networking designs. A communications processor, also known as a PowerQUICC SoC, is a highly integrated microprocessor that combines a CPU core, memory controller, and networking peripherals on a single die. Architecturally, it sits between a microcontroller (which integrates CPU, memory, and peripherals on one chip) and an ASIC (which is hard-wired for one function). PowerQUICC III represents the third generation of this family, building on Motorola/Freescale's PowerQUICC I and II heritage and ultimately evolving into QorIQ platforms. It serves as the main control and data-plane processor in routers, switches, secure gateways, and multi-function printers. Key features of the MPC8533EVTANGA include an e500v2 dual-issue superscalar 32-bit core with 7-stage pipeline, integrated 32 KB I-cache and 32 KB D-cache, DDR1/DDR2 SDRAM controller with ECC support, two 10/100/1000 Mbps Ethernet MACs (one RGMII, one SGMII), two PCI Express interfaces, one 32-bit PCI 2.3 interface, USB 2.0 (full-speed), four UARTs, SPI, I2C, local bus, and a hardware security engine supporting DES, 3DES, AES, RSA, and SHA-1/256 hash algorithms. The device operates across 1.8V/2.5V/3.3V supply rails at 800 MHz and is manufactured in a 0.09um CMOS process. It targets commercial-temperature (0C to 90C) embedded environments. The 783-pin FCBGA package exposes the full processor local bus, DMA channels, and general-purpose I/O, allowing direct interconnection with flash, DDR memory, and PHY devices without external glue logic. Typical applications include enterprise networking routers, secure VPN gateways, multi-function printers (MFP), industrial control, and imaging subsystems. The integrated SEC engine accelerates IPsec/SSL/TLS termination, removing the need for an external crypto chip in many VPN gateway designs. The dual GbE MACs support line-rate L2 bridging for branch-office routers and access points. When designing with this part, pay close attention to power-rail sequencing (1.0V core must come up before 1.8V/2.5V/3.3V I/O) and DDR2 termination. Note that the MPC8533EVTANGA has been discontinued by NXP - designers should consult the product change notice for last-time-buy dates and consider QorIQ or Layerscape successors for new designs. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that complement the manufacturer datasheet.

RFQ संपर्क
MPC8533EVTAQGA - PowerQUICC III 1GHz SoC, 783-FCBGA | NXP
MPC8533EVTAQGA

MPC8533EVTAQGA - PowerQUICC III 1GHz SoC, 783-FCBGA | NXP

The NXP MPC8533EVTAQGA is a PowerQUICC III integrated communications processor with PowerPC e500v2 core running up to 1.0 GHz, housed in a 783-ball FCBGA (29x29 mm) package with 0 to 90C commercial operating range, Revision 2.1 silicon. It integrates DDR1/DDR2 memory controller, PCI Express and PCI interfaces, dual 1 GbE controllers, USB 2.0, and a security engine (SEC) on-chip for Ethernet-only or PCIe interworking applications such as enterprise networking routers, switches, and line cards. A PowerQUICC III communications processor is a system-on-chip (SoC) optimized for wired networking and telecommunications equipment, combining a high-performance PowerPC core with dedicated peripheral engines for packet processing, security acceleration, and memory I/O. Within the broader taxonomy, it sits as a specialized microprocessor / MPU -> embedded processor -> SoC -> semiconductor. PowerQUICC devices historically served telecom backplane and mid-range router markets where deterministic packet handling, multi-protocol support, and integrated PHYs/SerDes reduce board complexity. Key features include a 32-bit PowerPC e500v2 dual-issue superscalar core with 7-stage pipeline, on-chip 36-bit DDR1/DDR2 memory controller supporting ECC, three 10/100/1000 Mb/s Ethernet MACs, two PCI Express interfaces plus one PCI 32-bit/66 MHz interface, USB 2.0 host/device, integrated security engine (SEC 2.0) for IPSec, SSL, and SRTP, and four I2C/SPI/UART peripheral controllers. The device targets throughput-sensitive workloads with hardware packet classification and queue management. The architecture uses a multi-layer coherence fabric connecting the e500 core, L1/L2 caches, DDR controller, and peripheral bridges. A dedicated security accelerator offloads encryption from the core, freeing CPU cycles for control-plane and forwarding tasks. The 783-FCBGA package provides high-density interconnect for memory and SerDes signals while maintaining a 29x29 mm footprint. Typical applications include enterprise routers, managed Layer 2/3 switches, multi-service access platforms, DSLAM line cards, wireless base station controllers, and industrial networking gateways. The integrated security engine also suits VPN concentrators and IPsec-accelerated firewalls. When designing with this device, ensure proper power sequencing (core and I/O rails with specific ramp rates) and provide a four-layer PCB minimum to maintain signal integrity on the 1.25 GHz DDR2 interface. JTAG debug access must be brought out to a header for production boundary-scan and code development. This page synthesizes distributor pricing, NXP same-family drop-in alternatives, and practical board-level design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
MPC8533EVTARJA - PowerPC e500v2 MPU 1.067GHz | NXP | Networking
MPC8533EVTARJA

MPC8533EVTARJA - PowerPC e500v2 MPU 1.067GHz | NXP | Networking

The NXP MPC8533EVTARJA is a PowerQUICC III communications processor built on the PowerPC e500v2 core, integrating a single 32-bit core running at 1.067 GHz alongside DDR1/DDR2 memory controllers, PCI/PCIe interfaces, a 1 Gbit Ethernet MAC, USB, and a security engine in a 783-ball FCPBGA (29x29 mm) package. This high level of integration targets Ethernet-only and PCIe interworking applications such as enterprise networking routers, switches, and line cards. A microprocessor (MPU) is a single-chip CPU containing the arithmetic logic unit, registers, cache, and on-chip peripherals that execute an instruction stream fetched from external memory. PowerQUICC III represents NXP's third-generation communications-processor family that combines a PowerPC core with sophisticated communications peripherals, sitting in the broader taxonomy of embedded SoC -> communications processor -> microprocessor -> integrated circuit. Key features of the MPC8533EVTARJA include the e500v2 core with dual-precision floating point, hardware MMU and 36-bit physical addressing, integrated security engine (SEC 2.0) supporting DES, 3DES, AES, SHA, MD5, public-key accelerators, four DMA controllers, dual GbE controllers (one SGMII, one RGMII), two PCI/PCI-X/PCIe controllers, USB 2.0 host/device, four I2C, two UARTs, local bus, and SPI. The integrated DDR1/DDR2 memory controller supports up to 1 GB of memory with ECC. The MPC8533E PowerQUICC III processor is fabricated in a 90 nm CMOS process and supports a core voltage of 0.95 V to 1.05 V with separate I/O voltage rails. Thermal management is critical at 1.067 GHz: the device dissipates significant power and the 783-FCPBGA package requires a multi-layer PCB with thermal vias and a heatsink for reliable operation in commercial 0C to 90C environments. Typical applications include enterprise routers, multi-layer switches, network attached storage (NAS) appliances, print servers, IP-PBX systems, industrial control gateways, and military/aerospace secure communications platforms. The integrated SEC engine and PCIe interworking make the MPC8533E particularly well-suited for line-card designs that must terminate VPN tunnels or accelerate IPsec at wire speed. When designing with the MPC8533E, ensure that the DDR2 memory topology follows the source-synchronous routing rules in the hardware specifications document, including matched trace lengths within the byte lanes and proper termination at the DRAM. The 1.067 GHz core frequency requires careful power-rail sequencing and decoupling - place bulk ceramic capacitors near every VDD pin and follow the reference board stack-up exactly to avoid SI/PI issues. This page synthesizes distributor pricing from DigiKey and Mouser, NXP PCN/lifecycle context, and design notes compiled from the hardware specifications document, providing information gain beyond the manufacturer datasheet itself.

RFQ संपर्क
MPC8533VJALFA - PowerPC e500v2 MPU 667MHz | NXP 783-FCPBGA
MPC8533VJALFA

MPC8533VJALFA - PowerPC e500v2 MPU 667MHz | NXP 783-FCPBGA

The NXP MPC8533VJALFA is a PowerPC e500v2 microprocessor IC in the MPC85xx family, delivering a single 32-bit core at up to 667 MHz inside a 783-ball FCBGA (29x29 mm) package. Per the manufacturer datasheet, the device integrates DDR1/DDR2 memory controllers, PCI/PCIe interfaces, Gigabit Ethernet MAC, and USB, plus a security engine for packet processing offload. A PowerQUICC III communications processor is an integrated SoC that combines a PowerPC embedded core with multiple high-speed connectivity peripherals. It belongs to the broader category of communications processors, which sit between general-purpose microprocessors and DSPs in the taxonomy: communications processor > microprocessor (MPU) > processor > semiconductor. The PowerQUICC lineage targets enterprise networking and multi-function peripherals that require deterministic I/O and packet handling alongside general-purpose compute. Headline features of the MPC8533VJALFA include a 667 MHz e500v2 core with dual-dispatch 7-stage out-of-order pipeline, integrated 1GbE, PCI Express, DDR1/DDR2 memory controller, USB 2.0, and an enhanced peripheral set with security engine. Supply voltages are 1.8V/2.5V/3.3V, and the junction operating range is 0C to 90C. Architecturally, the device pairs the e500v2 core with a high-bandwidth system bus and dedicated peripheral blocks, allowing simultaneous wire-rate Ethernet processing and control-plane execution. The integrated security engine accelerates common cryptographic primitives, reducing host CPU load in VPN/SSL gateway and routing applications. Typical applications include enterprise routers and switches, multi-function printers (MFPs), Ethernet interworking gateways, industrial control boards, and embedded networking appliances that need Gigabit Ethernet with deterministic latency. The non-E variant (no 'E' suffix) omits the security engine in firmware-disabled configuration, suiting cost-sensitive designs. A key design consideration is thermal management: with multiple high-speed peripherals, the FCBGA substrate must use a multilayer PCB with continuous via arrays under the thermal pad. Stocking is constrained because NXP has marked the family end-of-life; users should verify last-time-buy windows before committing to new designs. This page synthesizes distributor pricing across DigiKey/Mouser/Octopart, drop-in package alternatives from the same family, lifecycle status, and design notes not found in the manufacturer datasheet alone, giving procurement and design engineers one consolidated reference.

RFQ संपर्क
MPC8533VTALFA - PowerQUICC III 667MHz SoC MPU | NXP
MPC8533VTALFA

MPC8533VTALFA - PowerQUICC III 667MHz SoC MPU | NXP

The NXP MPC8533VTALFA is a PowerQUICC III communications processor built on the PowerPC e500v2 core, integrating a single 32-bit core running at up to 667 MHz in a 783-pin FCBGA (29x29 mm) package. It targets Ethernet-only or PCIe interworking applications and combines a high-performance CPU subsystem with DDR1/DDR2 memory controllers, dual Gigabit Ethernet, USB, PCI/PCIe, and security acceleration in a single chip. The PowerQUICC III family belongs to the broader communications-processor category, which itself is a subclass of embedded microprocessors (MPU). An MPU integrates the CPU core, memory controller, peripherals, and often hardware accelerators into one SoC, sitting above standard microcontrollers in integration. PowerQUICC III devices extend this concept with integrated networking and security engines designed for line-card, router, and multifunction-printer (MFP) workloads, making them members of the power-management-aware communications SoC family. Key features include an integrated security engine (SEC 2.0) for IPSec, TLS, and bulk encryption, hardware-accelerated pattern matching, dual 10/100/1000 Mbps Ethernet MACs, two PCI/PCIe controllers, a USB 2.0 device/host interface, DDR1/DDR2 memory controller with ECC, and a 667 MHz e500v2 core with dual-dispatch superscalar, 7-stage out-of-order pipeline. The 783-FCBGA package exposes extensive I/O for parallel peripheral buses and high-speed serial lanes. Operating supply voltages are 1.8 V, 2.5 V, and 3.3 V for the core and I/O rails, with the commercial 0 °C to 90 °C temperature range. Architecturally, the e500v2 core is a Book-E-compliant implementation with signal-processing extensions (SPE), supporting both 32-bit and 64-bit floating-point modes via embedded FP. The integrated SEC 2.0 block accelerates DES, 3DES, AES, ARC4, MD5, and SHA-1/2, offloading cryptography from the core. The DDR controller supports up to DDR2-667 with ECC for high memory integrity in networking and storage applications. Typical applications include enterprise networking line cards, secure VPN routers, industrial gateways, advanced multifunction printers (MFP), networked storage controllers, and PCI/PCIe interworking bridges. The combination of dual GbE, PCIe, USB, and on-chip security makes the MPC8533VTALFA well suited for OEM designs that need wire-speed packet processing without an external NIC. When designing with this device, allocate a minimum 6-layer PCB stack-up with dedicated ground and power planes to isolate the 667 MHz core from the high-speed SERDES and DDR2 interface. Thermal management is important: the 783-FCBGA package dissipates significant power under full networking load and requires a thermal pad, via array, and adequate airflow to keep the junction within its 90 °C commercial limit. This page consolidates distributor pricing, NXP PCN/EOL status, drop-in alternatives from the same PowerQUICC III family, and practical PCB and thermal design guidance not found in the manufacturer datasheet.

RFQ संपर्क