उत्पाद (44,000+)

MSP430F4361IPZ - 16-Bit 8MHz MCU with 24KB Flash | TI
MSP430F4361IPZ

MSP430F4361IPZ - 16-Bit 8MHz MCU with 24KB Flash | TI

The Texas Instruments MSP430F4361IPZ is a mixed-signal 16-bit RISC microcontroller operating at up to 8 MHz, with 24 KB of Flash memory, 1 KB of SRAM, and a 100-pin LQFP package. The device integrates a comparator, SPI and UART interfaces, and a 160-segment LCD driver for embedded control systems requiring substantial mixed-signal integration. A mixed-signal microcontroller combines a digital processor with analog and communication peripherals on one device. The MSP430F4361 belongs to the MSP430 mixed-signal microcontroller family, a 16-bit RISC architecture designed around low-power embedded control. Its integrated LCD driver is especially useful for segmented instrument panels, while the comparator supports threshold-based sensing and the serial interfaces provide flexible peripheral connectivity. The MSP430F4361IPZ provides a 125 ns instruction cycle time and an 8 MHz maximum clock. Its five low-power operating modes support battery-powered operation, and the manufacturer documents wake-up from standby in less than 6 us. The device also includes a frequency-locked loop, known as FLL+, which supports stable clocking where precise timing is required. An active mode specification of 1 MHz is listed for operating-current characterization. The integrated peripherals reduce the component count of a typical control board. A 160-segment LCD controller can drive a display directly, the comparator can perform hardware threshold comparisons, and SPI and UART provide paths to sensors, converters, memories, and service interfaces. These functions make the MCU suitable for metering, industrial panels, portable instruments, and embedded systems where board space and standby power are important considerations. Typical uses include digital utility meters, programmable laboratory instruments, compact industrial controllers, battery-powered monitors, and sensing systems with local displays. An SPI-connected sensor or external memory can share the same bus with a UART link used for configuration or service communication. The LCD segment count should be checked against the physical display layout before PCB routing because segment and common outputs determine the available display functions. A key design consideration is preserving low-power behavior across software and board-level decisions. Disable unused peripherals, select the appropriate low-power mode, and avoid floating inputs because they can increase current consumption. PCB layout should preserve the required decoupling arrangement, provide a stable reference and clock implementation, and route sensitive comparator inputs away from fast-switching nodes. This product page consolidates the manufacturer specifications, exact-ordering information, interface characteristics, application guidance, package details, and verified family alternatives into an engineering-oriented reference. It also highlights practical considerations for firmware power management, LCD implementation, peripheral sharing, and drop-in replacement assessment.

RFQ संपर्क
MSP430F436IPN - 8MHz 16-Bit 24KB Flash MCU | Texas Instruments
MSP430F436IPN

MSP430F436IPN - 8MHz 16-Bit 24KB Flash MCU | Texas Instruments

The Texas Instruments MSP430F436IPN is a 16-bit ultra-low-power mixed-signal microcontroller with an 8 MHz MSP430 CPU, 24 KB of Flash memory, 1 KB of SRAM, a 12-bit ADC, comparator, SPI/UART, and support for a 160-segment LCD. The device is packaged in an 80-pin LQFP (PN) package measuring 12 mm by 12 mm. Its combination of low power consumption, mixed-signal peripherals, and LCD-oriented I/O makes it suitable for industrial instrumentation, portable measurement equipment, meters, sensor nodes, and embedded control systems. An ultra-low-power microcontroller is a semiconductor device designed to conserve energy while executing embedded control and measurement functions. The MSP430 architecture combines a 16-bit RISC CPU, 16-bit registers, constant generators, and multiple low-power operating modes to reduce energy use in systems that spend substantial time waiting for external events. The MSP430F436IPN sits within the MSP430 mixed-signal family hierarchy: MCU, embedded microcontroller, mixed-signal microcontroller, and semiconductor. The most important verified specifications are the 8 MHz operating frequency, 24 KB Flash configuration, 1 KB SRAM, 12-bit ADC, comparator, SPI/UART connectivity, and 160-segment LCD capability. The Flash includes 24 KB of program storage plus 256 bytes as identified by the distributor listing, while the device uses 1 KB of SRAM for working data. The integrated ADC and comparator support analog measurement and thresholding without requiring separate discrete components, while serial interfaces provide connectivity to sensors, transceivers, and external data converters. The MSP430F436IPN uses the MSP430 CPU16 core and is specifically associated with the MSP430x4xx mixed-signal controller family. Its 80-pin LQFP package provides substantially more I/O than smaller microcontroller packages and is appropriate for designs requiring multiple LCD segments, analog inputs, serial communication, and general-purpose digital control. The LCSC product listing identifies an operating temperature range of -40 °C to +85 °C for this device. Typical applications include industrial panel meters, handheld multimeters, environmental and sensor monitoring devices, energy measurement equipment, portable medical or laboratory instruments, and low-power embedded controllers. In a meter design, the ADC and comparator can support analog front-end supervision while the LCD controller drives the display and SPI or UART provides communication with a host or sensor network. Designers should confirm the exact pin multiplexing, power requirements, clock configuration, ADC operating conditions, and display segment assignments against the manufacturer datasheet before layout. Decoupling, analog grounding, LCD bias generation, and unused-pin handling are important for reliable operation. Because the device combines precision measurement functions with extensive LCD and digital I/O, PCB layout should separate sensitive analog routing from switching and high-current paths. This page consolidates verified distributor pricing, manufacturer feature summaries, package information, comparison parameters, and application guidance for engineers evaluating the MSP430F436IPN. It is intended to support component selection and board-level planning, while the manufacturer datasheet remains the controlling source for electrical limits, timing, pin multiplexing, and production implementation.

RFQ संपर्क
MSP430F436IPZ - 8MHz 16-Bit MCU with 24KB Flash | Texas Instruments
MSP430F436IPZ

MSP430F436IPZ - 8MHz 16-Bit MCU with 24KB Flash | Texas Instruments

The Texas Instruments MSP430F436IPZ is an 8 MHz, 16-bit mixed-signal microcontroller with 24 KB of Flash memory, 1 KB of SRAM, a 12-bit ADC, comparator, SPI/UART connectivity, and 160-segment LCD support in a 100-pin LQFP (PZ) package. It combines an MSP430 CPU with embedded analog and mixed-signal peripherals for low-power instrumentation and control designs. A microcontroller is a programmable integrated circuit that combines a CPU, memory, and peripherals on one semiconductor device. The MSP430F436 belongs to the MSP430 mixed-signal microcontroller family, where the MSP430x4xx architecture adds higher-performance mixed-signal capabilities while retaining the low-power design focus of the MSP430 product line. Its 16-bit RISC core uses 16-bit registers and constant generators for efficient control operations. Key features include an 8 MHz maximum clock, 24 KB of programmable Flash, 1 KB of SRAM, and 48 I/O pins. The mixed-signal resources include a 12-bit ADC and comparator, while communications and timing resources include SPI, UART/USART, PWM, watchdog timer, and brown-out detection/reset. A 160-segment LCD driver supports display-oriented industrial, meter, and measurement equipment. The MSP430 architecture is designed around low-power operation, making the device suitable for battery-operated and intermittently powered products. Peripherals and the CPU can be controlled to reduce activity when measurements are not required. The 100-pin LQFP package provides substantially more I/O and peripheral routing flexibility than smaller microcontroller packages, although its 14 mm by 14 mm body requires more PCB area than compact QFN options. Typical applications include industrial panel meters, data loggers, portable measurement instruments, environmental monitoring equipment, battery-powered sensors, and LCD-driven control panels. The ADC supports analog measurement, the comparator supports threshold-based detection, and SPI or UART/USART provides a path to external sensors, memory, displays, or host systems. The integrated LCD capability is especially useful for local numeric or segmented status displays. Designers should verify the exact pin assignments, analog input multiplexing, LCD segment mapping, and peripheral channel allocation against the manufacturer pinout before PCB routing. The LQFP perimeter is fine-pitch, so careful pad design, solder mask control, and assembly inspection are important. Firmware should also account for the MSP430 clock setup, ADC conversion sequence, brown-out behavior, and low-power state transitions. This product page combines verified manufacturer and distributor specifications, same-family replacement analysis, package details, and practical design guidance. It is intended to help engineers confirm whether the MSP430F436IPZ matches the required memory, analog, communications, display, package, and low-power requirements before procurement or layout release.

RFQ संपर्क
MSP430F4371IPN - 8MHz 16-Bit MCU with 32KB Flash | TI
MSP430F4371IPN

MSP430F4371IPN - 8MHz 16-Bit MCU with 32KB Flash | TI

The Texas Instruments MSP430F4371IPN is an 8 MHz, 16-bit mixed-signal microcontroller with 32 KB of Flash memory, 1 KB of SRAM, a comparator, SPI/UART communications, and support for a 160-segment LCD in an 80-pin LQFP package. It combines the MSP430 RISC architecture with low-power operation and mixed-signal peripherals for embedded control, measurement, communications, and human-interface applications. An ultra-low-power mixed-signal microcontroller is a semiconductor device that integrates a CPU, memory, analog functions, and communication peripherals into one compact component. The MSP430 architecture uses 16-bit registers and constant generators to support efficient embedded software execution, while its low-power modes are intended to extend battery life in systems that spend substantial time asleep. The MSP430F4371IPN operates at up to 8 MHz and includes 32 KB of Flash for program storage plus 1 KB of SRAM for data. Its integrated comparator supports basic analog threshold and signal-conditioning tasks, while SPI and UART interfaces enable connection to sensors, displays, transceivers, and data-acquisition equipment. A 160-segment LCD capability can also reduce the need for separate display-driver circuitry in segmented-panel designs. The device belongs to the MSP430x43x mixed-signal family and uses the MSP430 CPU16 architecture. Its combination of 16-bit processing, Flash memory, SRAM, comparator resources, serial interfaces, and LCD support is useful where designers want one controller to handle both control logic and local human-interface functions. The 80-pin LQFP (PN) package provides substantially more I/O and peripheral connectivity than the smaller MSP430 devices intended for compact, low-pin-count designs. Typical applications include industrial panel controls, portable measurement instruments, low-power sensor nodes, data loggers, building-control modules, and compact serial-interface equipment. In a measurement product, the comparator can support fast threshold detection while the CPU handles control, calibration, and communications. SPI can connect to higher-bandwidth sensors or memory, while UART provides a simple interface for configuration and diagnostics. Designers should assign pins from the manufacturer pin-description table and verify the complete pin multiplexing, LCD-segment mapping, and peripheral-instance assignments for the selected firmware. The 80-LQFP layout also requires careful examination of exposed-pad, thermal, and board-routing requirements where those are specified for the package. Software configuration must account for the shared analog and digital peripheral resources rather than assuming every function is simultaneously available. This page combines the exact device identity, package, memory, interface, and temperature information with focused replacement guidance and engineering-oriented selection notes. It also distinguishes electrically similar MSP430 family members from confirmed drop-in choices, helping engineers assess PCB compatibility, firmware implications, and application suitability before committing to a replacement.

RFQ संपर्क
MSP430F4371IPZ - 16-Bit 8MHz MCU with 32KB Flash | Texas Instruments
MSP430F4371IPZ

MSP430F4371IPZ - 16-Bit 8MHz MCU with 32KB Flash | Texas Instruments

Texas Instruments MSP430F4371IPZ is a 16-bit mixed-signal microcontroller operating at up to 8 MHz, with 32 KB Flash memory, 1 KB SRAM, and a 100-pin LQFP package measuring 14 mm by 14 mm. The device also integrates a comparator, SPI and UART interfaces, and support for a 160-segment LCD, making it suitable for low-power embedded control and instrument-panel applications. A mixed-signal microcontroller is a semiconductor that combines a programmable digital controller with analog or mixed-signal peripheral functions. In the broader hierarchy, the MSP430F4371IPZ belongs to the MSP430 family of ultra-low-power microcontrollers, combining a 16-bit CPU with embedded Flash, RAM, communication interfaces, and an LCD controller. This integration reduces external component count while supporting designs that must balance processing performance, display drive, and energy efficiency. The primary features include an 8 MHz CPU clock, 32 KB Flash organized as 32K by 8 bytes plus 256 bytes, 1 KB SRAM, a comparator, SPI and UART connectivity, and a 160-segment LCD driver. The 100-pin LQFP package provides substantially more I/O than smaller MSP430 packages, which can simplify designs that require multiple external connections alongside a segmented display. Technically, the MSP430 architecture uses a 16-bit reduced-instruction-set CPU designed around fast register-based operation and multiple low-power operating modes. Its mixed-signal peripheral set allows a system to measure an analog condition with the integrated comparator while concurrently managing communications and display output. This combination is particularly useful when a design must preserve low-power behavior without adding separate analog, serial-interface, or LCD-driver components. Typical applications include industrial panel meters, portable instrumentation, energy-metering equipment, industrial controls, and low-power sensor nodes with local displays. The 160-segment LCD capability supports measurement readouts and status displays, while SPI and UART provide interfaces for external converters, memory, transceivers, or service communications. The 1 KB SRAM is more useful for real-time buffering than complex graphical user interfaces, but it is adequate for compact control algorithms and display data management. A primary design consideration is memory planning. Firmware, boot code, constants, and interrupt routines must fit within 32 KB Flash, while working variables and stack usage must remain within 1 KB SRAM. Board design should also preserve access to all exposed pins, provide a suitable decoupling network, and verify LCD segment, comparator, SPI, and UART assignments in the datasheet pin table before PCB routing. This product summary combines the manufacturer specifications with package, interface, sourcing, and application guidance. It also highlights the distinction between the target MSP430F4371IPZ configuration and related ordering options, helping engineers evaluate board compatibility, firmware constraints, and low-power mixed-signal design requirements before committing a layout.

RFQ संपर्क
MSP430F437IPN - 8MHz 16-Bit LCD MCU | Texas Instruments
MSP430F437IPN

MSP430F437IPN - 8MHz 16-Bit LCD MCU | Texas Instruments

Texas Instruments MSP430F437IPN is an 8 MHz, 16-bit mixed-signal microcontroller with 32 KB Flash, 1 KB SRAM, a 12-bit ADC, a comparator, SPI and UART interfaces, and support for a 160-segment LCD. The device is packaged in an 80-pin LQFP (PN) measuring 12 mm by 12 mm and is specified for operation from -40°C to 85°C. A mixed-signal microcontroller is a semiconductor that combines a digital processor core with analog measurement and interface functions. The MSP430 belongs to the MCU → 16-bit RISC microcontroller → embedded controller → mixed-signal semiconductor hierarchy. This integration lets a single MSP430F437IPN sample analog signals, control system logic, communicate through serial links, and drive segmented displays while reducing the number of discrete components required. The principal features include an MSP430 CPU16 processor operating at 8 MHz, 32 KB of Flash memory organized as 32K × 8 plus 256 bytes, 1 KB of SRAM, and a 12-bit ADC. The device also provides a comparator, SPI, UART, and a 160-segment LCD interface. Its operating range of 1.8 V to 3.6 V suits low-voltage embedded systems, while the industrial temperature range supports applications across industrial equipment, instrumentation, and control panels. The MSP430 architecture combines a 16-bit RISC core with mixed-signal peripherals and multiple low-power operating modes. Flash permits firmware and constants to be retained in the device, while SRAM supports working data and stack operations. The ADC and comparator allow analog front ends to share a processor with digital communication functions, reducing component count and simplifying firmware coordination. Typical applications include industrial measurement panels, portable instrumentation, energy-monitoring equipment, data loggers, LCD-based control systems, and embedded sensor nodes. SPI can support external sensors or memory, UART can provide a host or service interface, and the LCD controller can directly drive a segmented display. These functions are especially useful where a compact control panel must combine local visualization with serial communications. When designing around the MSP430F437IPN, preserve the 80-pin LQFP footprint, provide all required bypass capacitors close to the supply pins, and verify LCD segment mapping against the selected display. The 1.8 V to 3.6 V supply range also requires attention to sensor, ADC-reference, and communication-interface voltage limits. This product record combines the manufacturer’s ordering information, memory and peripheral details, low-voltage operating characteristics, package dimensions, and practical implementation guidance. It also identifies same-footprint MSP430 family alternatives and highlights the engineering checks required when changing between closely related mixed-signal microcontrollers.

RFQ संपर्क
MSP430F437IPZ - 8MHz 16-Bit MCU | Texas Instruments
MSP430F437IPZ

MSP430F437IPZ - 8MHz 16-Bit MCU | Texas Instruments

The Texas Instruments MSP430F437IPZ is an 8 MHz, 16-bit mixed-signal microcontroller with 32KB Flash, 1KB SRAM, a 12-bit ADC, comparator, SPI/UART, and 160-segment LCD support in a 100-pin LQFP package. It combines an MSP430 CPU16 RISC core with embedded analog and serial peripherals, making it suitable for low-power industrial, measurement, control, and instrumented applications. Its specified operating temperature range is -40°C to +85°C. A mixed-signal microcontroller is an embedded controller that integrates digital processing with analog conversion or analog comparison functions. In the hierarchy of embedded semiconductors, the MSP430F437IPZ belongs to the microcontroller family, combining a general-purpose CPU, nonvolatile program memory, SRAM, and peripherals on one device. Its 12-bit ADC supports analog measurement, while the comparator and LCD interface broaden the range of sensor, control-panel, and industrial instrument designs that can be handled without additional discrete components. The principal feature set includes an 8 MHz maximum clock, 32KB Flash memory, and 1KB SRAM. The DigiKey listing identifies the Flash organization as 32K × 8 plus 256 bytes. Serial connectivity includes SPI and UART, and the device supports up to 160 LCD segments, reducing the need for an external display driver in segment-oriented human-interface designs. The 100-pin LQFP PZ package exposes substantially more I/O and peripheral resources than the smaller MSP430 packages. The MSP430 architecture uses a 16-bit RISC core with 16-bit registers and constant generators designed to improve code efficiency. Rather than requiring a separate ADC, display interface, and communication controller, this device consolidates those functions around a low-power embedded platform. The exact ADC conversion rate, timer resources, supply-voltage limits, and detailed peripheral electrical characteristics should be confirmed in the manufacturer datasheet before a new design is released. Typical applications include industrial sensor acquisition, portable measurement instruments, low-power data loggers, serial-connected control modules, and LCD-based operator panels. The integrated ADC is useful when the system must monitor analog inputs, while UART and SPI provide paths to external sensors, converters, displays, or storage devices. The 160-segment LCD capability is particularly relevant to compact metering and monitoring equipment. When designing around the MSP430F437IPZ, verify the complete pin assignment, supply requirements, ADC reference configuration, and programming interface against the official datasheet. Decoupling, analog grounding, and LCD or serial signal routing should follow the layout recommendations in the manufacturer documentation. Firmware and peripheral configurations should also be validated at the intended 8 MHz operating condition. This product page consolidates verified manufacturer and distributor information, package and ordering data, cross-reference alternatives, and practical selection guidance. It is intended to help engineers identify the correct MSP430 device, understand its verified capabilities, and evaluate replacement options without treating unreported electrical details as guaranteed specifications.

RFQ संपर्क
MSP430F438IPN - 8MHz 16-Bit MCU with 48KB Flash | TI
MSP430F438IPN

MSP430F438IPN - 8MHz 16-Bit MCU with 48KB Flash | TI

The Texas Instruments MSP430F438IPN is an 8 MHz, 16-bit mixed-signal microcontroller with 48 KB of Flash memory, 2 KB of SRAM, a 12-bit ADC, a comparator, SPI/UART interfaces, and support for a 128-segment LCD in an 80-pin LQFP package. The MSP430 CPU16 architecture combines a reduced instruction set computer core with extensive mixed-signal resources for low-power embedded control, industrial instrumentation, metering, and portable measurement systems. A mixed-signal microcontroller is a semiconductor that integrates a digital processing core with analog measurement and output resources on one device. The MSP430 family belongs to the hierarchy of microcontroller, embedded processor, and semiconductor products. Its 16-bit RISC architecture, timer resources, communication peripherals, and low-power operating modes allow a compact design to acquire analog signals, process them locally, communicate with external equipment, and control an output without requiring a separate analog front end or communications processor. The verified device specification identifies an 8 MHz maximum clock, 48 KB Flash, 2 KB SRAM, a 12-bit ADC, comparator, SPI, UART, and 128-segment LCD support. The MSP430F438IPN operates from -40°C to +85°C and is supplied in an 80-pin LQFP (PN) package measuring 12 mm by 12 mm. The large package exposes the mixed-signal, communication, timer, debug, and LCD-related resources needed by applications with numerous external connections. The CPU16 core is designed for efficient control and measurement workloads. Its 16-bit arithmetic and register organization support compact data handling, while the integrated ADC allows an analog sensor to be digitized without a separate converter. Comparator and timer resources can support threshold detection, event timing, motor control, and periodic sampling. SPI and UART connectivity permits connection to sensors, displays, data loggers, wireless modules, and service interfaces. Typical uses include industrial panel meters, portable environmental monitors, laboratory instruments, data acquisition front ends, and embedded measurement equipment with segmented displays. The 128-segment LCD capability is particularly useful for compact numeric or alphanumeric instrument panels where a dot-matrix display would be unnecessarily costly or power-hungry. A system can therefore place sensing, local processing, human-interface feedback, and serial communication in one controller. When designing around this MCU, verify every peripheral signal against the manufacturer datasheet and provide adequate decoupling, programming access, reset behavior, and analog-input conditioning. The 80-pin LQFP footprint is relatively large compared with modern QFN packages, so the choice should account for board area and assembly cost. Firmware should also include brownout, watchdog, and clock-startup safeguards when field reliability is important. This page consolidates verified manufacturer and distributor information, package details, procurement data, selection guidance, and engineering considerations that help distinguish the MSP430F438IPN from related MSP430 devices without implying unverified drop-in replacements.

RFQ संपर्क
MSP430F439IPN - 8MHz 16-Bit MCU with 60KB Flash | Texas Instruments
MSP430F439IPN

MSP430F439IPN - 8MHz 16-Bit MCU with 60KB Flash | Texas Instruments

Texas Instruments MSP430F439IPN is an 8 MHz mixed-signal microcontroller with a 16-bit RISC CPU, 60 KB of Flash program memory, 2 KB of SRAM, a 12-bit ADC, a comparator, SPI and UART interfaces, and support for a 128-segment LCD in an 80-pin LQFP package. The device combines embedded control, analog measurement, and low-power operation in a single integrated circuit designed for portable instruments and industrial measurement systems. A mixed-signal microcontroller is an embedded controller that combines a digital processor with analog and communication peripherals. The MSP430 architecture belongs to the microcontroller, embedded-controller, and semiconductor hierarchies and uses a 16-bit RISC processor with 16-bit registers. This allows the MSP430F439 to acquire analog measurements, process data, and communicate through serial interfaces while retaining multiple low-power operating modes for battery-powered equipment. Principal features include an 8 MHz maximum clock, 60 KB of Flash memory, 2 KB of SRAM, 48 I/O pins, a 12-bit ADC, an analog comparator, SPI and UART connectivity, and a 128-segment LCD controller. Five power-saving modes are available, supporting applications in which the controller must remain responsive while minimizing energy consumption. The broad peripheral set reduces the need for external analog, interface, and display-support devices in compact designs. The 16-bit CPU16 architecture is suitable for sensor acquisition, signal conditioning, control loops, and local data handling. The integrated 12-bit ADC provides the measurement channel needed for battery, industrial process, or portable diagnostic equipment, while the comparator supports threshold-based sensing. SPI and UART provide paths to external sensors, transceivers, storage devices, and service interfaces without requiring a dedicated communications controller. Typical applications include portable environmental monitors, industrial process-control panels, battery-powered test instruments, multi-channel sensor acquisition systems, data loggers, and embedded metering products. A dedicated 128-segment LCD controller is particularly useful for local numerical or status displays, allowing measured values and operating states to be shown without an additional display controller. Designers should review the device's power-mode timing, analog-input requirements, and I/O assignments in the manufacturer datasheet. Keep analog and digital return paths organized, place input filtering close to the device, and confirm external-component requirements for the selected precision reference and operating voltage. The 80-pin LQFP footprint also requires adequate board area and careful fanout for the analog, communications, display, and debug connections. This product overview combines the manufacturer device specifications, package details, functional architecture, application guidance, and drop-in comparison information in one engineering-focused reference. It is intended to help engineers identify whether the MSP430F439IPN provides the required memory, analog resources, display support, interfaces, and low-power behavior before completing a PCB or firmware design.

RFQ संपर्क
MSP430F447IPZ - 8MHz 16-Bit MCU with 32KB Flash | Texas Instruments
MSP430F447IPZ

MSP430F447IPZ - 8MHz 16-Bit MCU with 32KB Flash | Texas Instruments

The Texas Instruments MSP430F447IPZ is an 8 MHz 16-bit mixed-signal microcontroller with 32KB Flash memory, 1KB SRAM, a 12-bit ADC, comparator, SPI/UART, and 160-segment LCD support in a 100-LQFP package. It combines an MSP430 RISC CPU with low-power operating modes for portable measurement and embedded control systems. A mixed-signal microcontroller integrates a digital processor with analog conversion and comparison functions on one device. The MSP430 architecture belongs to the microcontroller, embedded processor, and semiconductor hierarchy, while its ADC, comparator, serial interfaces, and LCD driver make it especially useful for battery-powered instruments, panel meters, and industrial sensing equipment. Key features include an 8 MHz maximum clock, 32KB Flash organized as 32K x 8 plus 256 bytes, 1KB SRAM, a 12-bit ADC, an internal comparator, SPI and UART connectivity, and support for up to 160 LCD segments. These resources allow firmware to combine acquisition, signal conditioning, display driving, and serial communication without requiring several discrete devices. The MSP430 CPU uses a 16-bit RISC architecture with 16-bit registers and constant generators. Its mixed-signal peripherals support sampled data acquisition and threshold comparison, while the LCD controller reduces the external display-driver burden for segmented instruments. The manufacturer describes the family as optimized for low-power portable measurement applications, with five low-power modes available for duty-cycled operation. Typical uses include digital multimeters, environmental monitors, portable industrial meters, panel instruments, and connected measurement equipment. The combination of 32KB Flash, 1KB SRAM, ADC, comparator, UART, SPI, and segmented LCD support is particularly useful when a compact embedded design must collect analog measurements, apply thresholds, update a local display, and exchange data with a host. Designers should allocate pins and firmware carefully for LCD segments, analog inputs, serial interfaces, and mixed-signal grounding. Follow the pin-description table in the manufacturer datasheet when assigning tracks, and keep analog and digital return currents separated where the application board layout permits. Verify the operating voltage, temperature grade, and peripheral configuration for the exact ordering code before production release. This product page combines the device specifications, pin-package information, functional alternatives, and engineering-oriented comparison notes to support faster component selection and board-level planning.

RFQ संपर्क
MSP430F4481IPZ - 8MHz 48KB Flash MCU | Texas Instruments
MSP430F4481IPZ

MSP430F4481IPZ - 8MHz 48KB Flash MCU | Texas Instruments

Texas Instruments MSP430F4481IPZ is an ultra-low-power 16-bit mixed-signal microcontroller with an 8 MHz MSP430 RISC CPU, 48 KB of flash memory, 2 KB of SRAM, and a 100-pin LQFP package measuring 14 x 14 mm. The device integrates a 12-bit ADC, comparator, SPI, UART, and a 160-segment LCD driver for low-power measurement and portable instrumentation. An ultra-low-power microcontroller is a semiconductor designed to execute firmware while minimizing energy consumption during active operation, standby, and off states. The MSP430 architecture combines a 16-bit RISC processor, 16-bit registers, and constant generators within a mixed-signal system-on-chip hierarchy. This makes it suitable for battery-powered instruments, industrial meters, and embedded systems that require analog measurement and segmented-display control without separate peripheral ICs. The principal features include an 8 MHz maximum clock, 48 KB flash, 2 KB SRAM, a 12-bit analog-to-digital converter, comparator, SPI and UART interfaces, and support for a 160-segment LCD. The integrated analog and display resources reduce board area and external component count. A 1.8 V to 3.6 V operating range also supports low-voltage portable systems. The MSP430 CPU uses a 16-bit RISC architecture with 16-bit registers and constant generators to improve code efficiency. The mixed-signal feature set connects the ADC and comparator to general-purpose processing, while the LCD driver supports meter and panel-display applications. The device also provides five low-power operating modes for reducing energy use between measurement events. Typical uses include handheld multimeters, smart energy meters, industrial process monitors, portable medical instruments, and embedded measurement systems with LCD displays. SPI and UART connectivity allows the controller to communicate with external sensors, transceivers, or data loggers, while the LCD driver simplifies direct segment-display control. For PCB implementation, use the manufacturer's 100-pin LQFP land pattern and follow the pin-description table in the datasheet when assigning power, ground, analog, and communication functions. Pay particular attention to analog supply routing, ADC input conditioning, LCD segment drive current, and decoupling placement to preserve measurement performance. This page combines the MSP430F4481IPZ specifications, application guidance, package information, and verified drop-in alternatives to support component selection, schematic design, PCB layout, and sourcing decisions without duplicating the raw manufacturer datasheet tables.

RFQ संपर्क
MSP430F448IPZ - 8MHz 48KB MCU | Texas Instruments
MSP430F448IPZ

MSP430F448IPZ - 8MHz 48KB MCU | Texas Instruments

The Texas Instruments MSP430F448IPZ is a 16-bit mixed-signal microcontroller with an 8 MHz MSP430 CPU, 48 KB of flash memory, 2 KB of SRAM, and a 12-bit ADC, packaged in a 100-pin LQFP (PZ). The device also integrates a comparator, SPI and UART interfaces, and support for a 160-segment LCD. Its operating-voltage range is 1.8 V to 3.6 V. A mixed-signal microcontroller combines a programmable digital controller with analog measurement functions on one integrated circuit. The MSP430F448 belongs to the MSP430 family of ultra-low-power RISC microcontrollers, where the CPU core, memory, timers, serial interfaces, and analog peripherals share a low-power architecture. The 16-bit RISC instruction set and 16-bit registers support efficient control workloads, while hardware peripherals allow measurements and communications to continue without excessive software overhead. Key features include an 8 MHz maximum clock frequency, 48 KB flash for firmware storage, 2 KB SRAM for working data, and a 12-bit ADC for analog sensing. The integrated comparator supports threshold-based signal detection, while SPI and UART provide wired peripheral connectivity. According to the manufacturer datasheet, active-mode current is 280 uA at 1 MHz and 2.2 V, standby current is 1.1 uA, and RAM-retention off-mode current is 0.1 uA. Wake-up from standby takes less than 6 us. The MSP430 architecture is based on a 16-bit RISC core with 16-bit registers and constant generators. Five power-saving modes let firmware balance response time against energy use, which is particularly valuable in battery-operated measurement equipment. The 12-bit ADC and comparator place analog input conditioning and digital control in the same device, while the LCD controller can drive up to 160 segments without requiring a separate display controller. The integrated communication peripherals reduce board area in compact instruments. Typical applications include low-power industrial measurement systems, portable environmental monitors, digital multimeters, data loggers, smart metering equipment, battery-powered instrumentation, and control panels with segment LCD displays. The device is particularly suitable when a compact 100-pin package can accommodate the extensive analog and LCD resources without requiring a separate LCD driver or precision converter. Design around the MSP430F448IPZ requires attention to decoupling, analog grounding, LCD drive routing, and low-power behavior. Place input and output capacitors close to their associated power pins, keep analog traces away from fast-switching LCD and serial signals, and use the manufacturer pin-description table when assigning all 100 pins. Firmware should configure unused peripherals and GPIO pins appropriately to avoid unintended current consumption. This page combines manufacturer specifications, procurement information, drop-in replacement research, and application-focused engineering guidance. It also identifies differences among nearby MSP430 devices so that designers can verify memory capacity, peripheral availability, pin compatibility, and operating requirements before approving a substitution.

RFQ संपर्क
MSP430F448IPZR - 8MHz 16-Bit MCU with 48KB Flash | TI
MSP430F448IPZR

MSP430F448IPZR - 8MHz 16-Bit MCU with 48KB Flash | TI

Texas Instruments MSP430F448IPZR is an 8 MHz, 16-bit mixed-signal microcontroller with 48 KB of flash memory, 2 KB of SRAM, a 12-bit ADC, comparator, SPI/UART peripherals, and support for a 160-segment LCD. The device is packaged in a 100-pin LQFP (PZ) package and is specified for an operating temperature range of -40°C to 85°C. It combines an MSP430 RISC core, mixed-signal peripherals, and low-power operation in one mixed-signal MCU. An MSP430 mixed-signal microcontroller combines a low-power RISC processor with analog and communication peripherals on a single integrated circuit. The MSP430 family belongs to the broader embedded-controller hierarchy, where flash-programmable microcontrollers provide programmable control, data acquisition, and serial communication for compact electronic products. Its architecture emphasizes efficient execution, multiple low-power operating states, and deterministic peripheral interaction for battery-powered and portable measurement systems. The principal features of the MSP430F448IPZR include an 8 MHz maximum clock, 48 KB flash, 2 KB SRAM, a 12-bit analog-to-digital converter, an analog comparator, SPI and UART connectivity, and a 160-segment LCD driver. Flash memory supports firmware and constants, while SRAM provides working memory for acquisition and control routines. The integrated mixed-signal peripherals reduce the number of external components needed for sensor measurement, local display, and communication. The MSP430 architecture uses a 16-bit RISC CPU with 16-bit registers. Its low-power design is particularly useful in portable measurement products where duty-cycled operation can extend battery life. Peripherals are integrated for direct sensor interfacing, while the LCD driver allows local status or measurement display without another display controller. The manufacturer describes the MSP430 family as being optimized for extended battery life in portable measurement applications. Typical uses include portable environmental monitors, industrial panel meters, handheld test instruments, connected sensor nodes, and low-power data-acquisition equipment. The 12-bit ADC supports analog measurement, the comparator handles threshold detection, SPI permits attachment to higher-bandwidth sensors or memory, UART supports simple host communication, and the LCD driver is useful in local-display instruments that need to operate without a continuous graphics processor. PCB design should preserve the MSP430's low-noise analog performance by routing ADC inputs away from switching nodes and keeping supply and ground paths stable. Decoupling capacitors should be placed close to the relevant power pins, and the analog ground and digital ground strategy should follow the device's recommended layout guidance. Firmware should also use the documented low-power modes and avoid unnecessary polling so that the MCU spends more time in its lowest-energy states. This product page combines the manufacturer's device characteristics, ordering information, technical features, application guidance, pin-package details, and carefully qualified replacement analysis. It is intended to help engineers evaluate clock speed, memory, analog conversion resolution, communication interfaces, LCD capability, power behavior, package compatibility, and sourcing requirements before finalizing an embedded design.

RFQ संपर्क
MSP430F449IPZ - 8MHz 16-Bit MCU with 60KB Flash | TI
MSP430F449IPZ

MSP430F449IPZ - 8MHz 16-Bit MCU with 60KB Flash | TI

The Texas Instruments MSP430F449IPZ is an ultra-low-power, mixed-signal 16-bit microcontroller operating at up to 8 MHz, with 60 KB of flash memory, 2 KB of SRAM, a 12-bit ADC, and a 100-pin LQFP package. It integrates SPI, UART, a comparator, and support for a 160-segment LCD, making it suitable for compact embedded control and measurement systems. A mixed-signal microcontroller combines digital processing with analog measurement and interface functions on one device. The MSP430 belongs to the microcontroller hierarchy, where its 16-bit RISC core executes control software while integrated ADC, comparator, serial interfaces, and LCD capability reduce the number of external components. This integration is especially useful in instruments, meters, industrial controls, and portable products where board area, response time, and low standby power are important. Key features include 60 KB of flash for firmware, 2 KB of SRAM for working data, an 8 MHz CPU clock, and a 12-bit ADC for analog measurements. Two UART channels and SPI connectivity support external sensors, transceivers, displays, and data acquisition components. The integrated comparator can perform threshold detection and monitor fast or low-current signals, while the 160-segment LCD capability targets meter and human-interface applications without requiring a separate display controller. The MSP430 architecture uses a 16-bit RISC core with 16-bit registers and constant generators to improve code efficiency. Its mixed-signal feature set places acquisition, control, communications, and display handling in a single package. The MSP430F449IPZ therefore supports a consolidated control architecture in which sensor inputs, operator displays, and communications peripherals can operate around a central low-power processor. Typical applications include handheld and bench-top measurement instruments, industrial panel meters, data loggers, low-power environmental monitors, and embedded systems requiring segmented LCD displays. Its 48 I/Os provide additional connectivity for sensors, switches, indicators, and external interface components. SPI and UART links allow the controller to communicate with transceivers, memory devices, converters, or service interfaces without requiring several dedicated peripheral chips. Design the PCB with attention to analog grounding, ADC input conditioning, and LCD glass routing. Keep analog and digital return paths disciplined, place bypass capacitance close to the supply pins, and follow the manufacturer pin description and layout guidance when assigning the 100 package pins. The -40 °C to +85 °C temperature range supports industrial-temperature designs, while final operating limits should be checked against all electrical and timing requirements. This product page combines the manufacturer specifications, a same-package replacement comparison, application guidance, and PCB-oriented design notes. It is intended to help engineers assess the MSP430F449IPZ for mixed-signal control designs, verify interface compatibility, and plan a low-power embedded architecture before requesting a quote.

RFQ संपर्क
MSP430F4616IPZ - 16-Bit 8MHz MCU with 92KB Flash | TI
MSP430F4616IPZ

MSP430F4616IPZ - 16-Bit 8MHz MCU with 92KB Flash | TI

Texas Instruments MSP430F4616IPZ is a 16-bit RISC mixed-signal microcontroller operating at up to 8 MHz, with 92 KB of flash memory, 4 KB of SRAM, and a 100-pin LQFP package measuring 14 x 14 mm. It integrates a 12-bit ADC, comparator, DMA controller, I2C, SPI, UART, and a 160-segment LCD driver. A microcontroller is a programmable semiconductor containing a CPU, memory, and peripherals on one integrated circuit. The MSP430 belongs to the ultra-low-power MCU category, combining a 16-bit RISC CPU, 16-bit registers, and five low-power modes. This hierarchy places it among embedded processors designed for portable measurement, industrial instrumentation, and control systems where energy efficiency and integrated analog functions influence system size. The MSP430F4616IPZ provides 92 KB of flash for firmware and 4 KB of SRAM for working data. Its 12-bit ADC supports precision signal acquisition, while the comparator supports threshold-based monitoring. DMA reduces interrupt overhead during data movement, and the I2C, SPI, and UART interfaces cover common sensor, display, and communication links. The integrated 160-segment LCD controller reduces external display-driver requirements in instrument-panel designs. Texas Instruments describes the MSP430 family architecture around a powerful 16-bit RISC CPU, 16-bit registers, constant generators, and five low-power modes optimized for extended battery life in portable measurement equipment. The target operates from a 3.3 V supply according to its product listing. Its 100-LQFP package provides 100 external pins, making the device particularly suitable for designs requiring broad analog, digital, and LCD connectivity. Typical uses include industrial process transmitters, portable environmental monitors, energy-measurement instruments, medical monitoring equipment, battery-powered data loggers, and human-machine interface controllers. The combination of embedded LCD control, serial interfaces, ADC capability, and low-power operating modes allows a compact design without requiring a separate ADC and display controller. PCB implementation should preserve short analog paths around the ADC inputs and provide clean supply decoupling. Confirm the complete 100-pin signal assignment, exposed package details, clocking configuration, and programming interface in the manufacturer datasheet before layout release. The software plan should also define which low-power mode is retained during idle periods and how interrupts wake the device. This product page consolidates the exact ordering information, core memory and interface specifications, qualified comparison points, application guidance, and practical design considerations engineers need when evaluating the MSP430F4616IPZ for an embedded mixed-signal design.

RFQ संपर्क
MSP430F477IPN - 8MHz 16-Bit Sensing MCU | Texas Instruments
MSP430F477IPN

MSP430F477IPN - 8MHz 16-Bit Sensing MCU | Texas Instruments

Texas Instruments MSP430F477IPN is an 8-MHz ultra-low-power sensing microcontroller with one 16-bit sigma-delta ADC, one 12-bit DAC, 128-segment LCD support, 32KB Flash, and 2KB RAM in an 80-pin LQFP package. The device operates from 2.5V or 3.3V and is specified over -40°C to +85°C. A microcontroller is a programmable semiconductor that integrates a CPU, memory, and peripherals into a single device. The MSP430F477 belongs to the MSP430 family, whose 16-bit RISC architecture, 16-bit registers, and five low-power modes are optimized for portable measurement systems. It combines a general-purpose MCU with precision conversion and segmented-display resources, reducing the number of discrete components needed in sensing instruments. Principal features include an 8-MHz maximum clock, 32KB of program Flash with an additional 256 bytes, and 2KB of RAM. The sensing subsystem provides a 16-bit sigma-delta ADC and a 12-bit DAC, while the integrated LCD controller supports displays with up to 128 segments. Up to 48 I/O pins provide external connections for sensors, controls, communications, and display elements. The MSP430 architecture uses a 16-bit RISC CPU with 16-bit registers and five low-power modes for portable measurement applications. Its mixed-signal resources allow an analog input to be digitized without adding a separate high-resolution ADC package. The 12-bit DAC provides an analog output, making the MCU applicable to control loops, excitation, calibration, and signal-generation systems where the required resolution does not demand a dedicated converter. Typical uses include industrial panel meters, portable environmental monitors, laboratory instruments, connected sensing nodes, data-acquisition modules, and low-power display products. The 128-segment LCD capability is especially useful for human-readable measurement displays, while the sigma-delta ADC supports precision sensor acquisition and the DAC supports analog control outputs. Designers should preserve the analog and digital grounding strategy required by the sensing peripherals, provide the specified bypass and reference-network components, and validate LCD and external-signal routing in the target enclosure. Component choices should also be checked against the exact ordering information, temperature range, package, and converter requirements in the manufacturer documentation. This page consolidates verified manufacturer, distributor, and distributor-search information for the MSP430F477IPN, including practical application guidance, parameter comparisons, sourcing links, and explicit uncertainty markers where price, full pinout, and verified drop-in replacements were not available.

RFQ संपर्क
MSP430F477IZCA - 8MHz Sensing MCU, 32KB Flash | Texas Instruments
MSP430F477IZCA

MSP430F477IZCA - 8MHz Sensing MCU, 32KB Flash | Texas Instruments

Texas Instruments MSP430F477IZCA is an 8-MHz MSP430 sensing microcontroller with a 16-bit RISC CPU, 32KB of flash memory, 2KB of RAM, one 16-bit sigma-delta ADC, a 12-bit DAC, and a 128-segment LCD controller. The device is supplied in a 113-pin NFBGA (ZCA) package measuring 7 mm by 7 mm. Its mixed-signal and display resources support portable measurement systems that require analog conversion, low-power operation, and compact embedded control. An MSP430 sensing microcontroller is an embedded mixed-signal controller that combines a low-power RISC processing core with peripherals designed for sensing, measurement, display, and communication functions. The MSP430 family uses a 16-bit architecture with 16-bit registers and five low-power modes designed to extend operating time in battery-powered portable measurement equipment. MSP430F477IZCA combines those power-management capabilities with dedicated ADC, DAC, and LCD resources rather than relying entirely on external discrete components. The principal features include an 8-MHz operating frequency, 32KB flash organized as 32K by 8 bytes with an additional 256-byte information region, and 2KB of RAM. The analog subsystem includes one 16-bit sigma-delta ADC and a 12-bit DAC. A 128-segment LCD controller supports segmented-display products such as handheld meters, industrial panels, and portable instruments while reducing the need for external display-control hardware. The 113-pin NFBGA package supports a dense mixed-signal design but requires careful PCB layout, BGA assembly capability, and controlled escape routing. Texas Instruments describes the NFBGA package as offering electrical performance equivalent to the conventional package and a board-layout and footprint equivalent to the referenced package. Package migration therefore still requires review of pin assignment, thermal behavior, solder-mask design, and assembly process requirements. Typical applications include precision measurement instruments, low-power data loggers, handheld meters, sensor-interface systems, industrial monitoring panels, and connected laboratory equipment. The combination of local analog conversion, LCD control, flash-resident firmware, and RAM-based acquisition can simplify systems that would otherwise require separate data-conversion and display devices. PCB implementation should preserve the exact pin assignments and recommended BGA land pattern from the manufacturer datasheet. Confirm pad geometry, solder-mask opening, assembly profile, and thermal conditions before release because the 113-pin NFBGA footprint is not interchangeable with a generic QFP or a BGA having a different ball count. Firmware development should use the MSP430 toolchain and configure the ADC, DAC, LCD, clocks, and low-power modes according to the device reference information. This product record combines the manufacturer device description, package and memory details, conversion resources, and application-oriented design guidance to support component selection, PCB planning, firmware preparation, and sourcing decisions.

RFQ संपर्क
MSP430F477IZQW - 8MHz 32KB Flash MCU | Texas Instruments
MSP430F477IZQW

MSP430F477IZQW - 8MHz 32KB Flash MCU | Texas Instruments

Texas Instruments MSP430F477IZQW is a 16-bit mixed-signal microcontroller built around the MSP430 CPU16 core, operating up to 8 MHz with 32 KB of Flash memory and 2 KB of RAM in a 113-BGA Microstar Junior package measuring 7 x 7 mm. A mixed-signal microcontroller combines a general-purpose processor with analog and timing peripherals for measurement and control systems. The MSP430 architecture belongs to the MCU hierarchy and uses a 16-bit RISC core, 16-bit registers, and five low-power operating modes. This combination positions the device for portable, battery-powered instrumentation where local sensing, display control, and data acquisition must coexist within a compact footprint. The device integrates a 16-bit Sigma-Delta ADC, a 12-bit DAC, and a controller for a 128-segment LCD. It also includes brown-out detection and reset, PWM capability, and a watchdog timer. These peripherals support signal conditioning, output generation, timing, and system supervision without requiring each function to be implemented externally. A separate 256-byte Flash information region accompanies the 32 KB program memory. The MSP430F477 uses a 16-bit RISC processor with 16-bit registers. Its 8 MHz maximum clock rate provides deterministic control capability for portable measurement equipment, while the five low-power modes are intended to extend battery life. The Sigma-Delta ADC is particularly relevant to sensors that produce low-frequency or precision-oriented signals, and the LCD controller supports display-heavy handheld instruments without external display-control logic. Typical uses include handheld meters, environmental monitors, industrial sensing terminals, medical measurement instruments, portable gas analyzers, and smart-panel controllers. In each case, the MCU can acquire sensor data, perform control calculations, drive an LCD, and supervise the power system. Operation from 2.5 V or 3.3 V also supports compact battery-powered products and portable industrial equipment. The principal design consideration is package complexity. The 113-BGA footprint requires careful PCB layout, via-in-pad or escape-routing strategies, assembly process control, and reliable inspection. Engineers should follow the TI datasheet land pattern, ball assignment, and recommended reflow profile rather than infer layout dimensions from the 7 x 7 mm package outline. This product page combines the manufacturer's core device characteristics with practical application guidance, power-management context, and an engineering-focused comparison of compatible same-family microcontrollers for prototype and production planning.

RFQ संपर्क
MSP430F4784IPZ - 16MHz 48KB Flash Metering MCU | Texas Instruments
MSP430F4784IPZ

MSP430F4784IPZ - 16MHz 48KB Flash Metering MCU | Texas Instruments

The Texas Instruments MSP430F4784IPZ is a 16 MHz single-phase metering microcontroller with four sigma-delta ADCs, 160-segment LCD support, 48 KB of Flash memory, 2 KB of RAM, and 100 leads in a 14 mm LQFP package. It combines a 16-bit RISC CPU, 16-bit registers, mixed-signal measurement circuitry, and low-power operation in one device designed for energy-metering and portable measurement systems. An MCU is a programmable semiconductor containing a processor core, memory, and peripherals on one integrated circuit. The MSP430 family belongs to the embedded-controller and power-management hierarchy, using a 16-bit RISC architecture optimized for low-power measurement. Its five low-power modes help reduce energy consumption when a meter is mostly idle, while the mixed-signal peripherals acquire analog quantities and drive segmented displays without requiring a separate interface processor. The MSP430F4784IPZ provides four sigma-delta ADCs for metering-oriented signal acquisition and supports a 160-segment LCD. Its 48 KB Flash capacity supports firmware, calibration data, and metering algorithms, while 2 KB of RAM provides working memory for acquisition and display processing. The 16 MHz CPU clock supports timely execution of measurement routines and communication tasks, and the industrial-temperature ordering option is identified by the IPZ suffix. The device belongs to the MSP430x47x4 mixed-signal controller family. Its architecture combines a 16-bit RISC CPU with dedicated analog measurement and LCD resources, reducing the component count required in a meter design. The four sigma-delta channels are suited to slowly varying or high-resolution measurements where averaging and digital filtering are important. Because firmware determines calibration, gain, filtering, and conversion scheduling, the same silicon can support different meter configurations without changing the PCB. Typical uses include single-phase electricity meters, utility data-acquisition equipment, portable industrial measurement instruments, energy-monitoring gateways, and low-power display products. In these systems, the MCU can sample analog channels, apply calibration and filtering, maintain metering state, update an LCD, and supervise a communications interface. A dedicated metering MCU is preferable when predictable low-power behavior and local display control are more important than the broader ecosystem of a general-purpose MCU. Design the PCB around the 100-lead LQFP footprint and place the LCD, analog inputs, crystal circuitry, and decoupling according to the manufacturer datasheet. Keep sigma-delta analog traces away from fast-switching nodes, provide stable references, and verify startup, calibration, and low-power wake behavior across the complete temperature range. Allow sufficient board area around exposed thermal and power paths where the package design requires them. This product page combines the exact orderable MPN, manufacturer device characteristics, package and memory information, sourcing guidance, and practical selection considerations. It also distinguishes verified drop-in candidates from functionally similar controllers, helping engineers assess replacement risk before committing a 100-lead mixed-signal design to production.

RFQ संपर्क
MSP430F478IPN - 16-Bit 8MHz Sensing MCU | Texas Instruments
MSP430F478IPN

MSP430F478IPN - 16-Bit 8MHz Sensing MCU | Texas Instruments

The Texas Instruments MSP430F478IPN is a 16-bit, 8 MHz mixed-signal sensing microcontroller with 48 KB of Flash memory, 2 KB of RAM, one 16-bit Sigma-Delta ADC, one 12-bit DAC, and a 128-segment LCD controller in an 80-LQFP 12 x 12 mm package. It combines the MSP430 CPU16 architecture with integrated analog conversion and LCD drive functions for compact, low-power sensing systems. An MCU is an integrated circuit containing a processor core, memory, peripherals, and interfaces on one die. The MSP430F478 belongs to the mixed-signal microcontroller category within the broader embedded-controller and semiconductor hierarchy. Its sensing-oriented feature set allows a design to acquire analog measurements, process them in software, and present information through an LCD without requiring several separate discrete components. Key features include an 8 MHz maximum clock, 48 KB of Flash program memory, 2 KB of RAM, one 16-bit Sigma-Delta ADC, one 12-bit DAC, support for a 128-segment LCD, and 48 I/O pins. The industrial temperature grade and 80-LQFP package make the device suitable for compact embedded products that require both digital control and analog measurement functions. The MSP430 CPU16 architecture uses a 16-bit register-oriented design intended for low-power embedded control. Flash memory provides 48 KB for firmware, while 2 KB of RAM supports working data. The Sigma-Delta ADC is suited to measurement channels where integrated conversion is useful, and the 12-bit DAC provides an analog output for control or reference applications. The LCD controller can reduce the component count in segment-display designs. Typical applications include industrial panel meters, portable environmental monitors, laboratory instruments, digital thermometers, data loggers, and compact control panels. These uses benefit from combining an ADC, DAC, LCD drive, and microcontroller in a single package while limiting board area and external component count. Designers should verify the complete pin assignment, operating limits, ADC and DAC electrical characteristics, and recommended decoupling directly from the manufacturer datasheet before layout. The supplied verified data identifies the 80-LQFP package but does not provide a public pin-by-pin mapping, so this record does not infer one. This page consolidates verified manufacturer and distributor information, current sourcing data, structured specification gaps, and practical application guidance. It also distinguishes documented facts from unavailable pin-level, pricing-tier, and drop-in replacement data so engineers can make sourcing and design decisions without unsupported assumptions.

RFQ संपर्क
MSP430F4793IPZ - 16MHz Metering MCU | Texas Instruments
MSP430F4793IPZ

MSP430F4793IPZ - 16MHz Metering MCU | Texas Instruments

Texas Instruments MSP430F4793IPZ is a 16 MHz single-phase metering microcontroller with three sigma-delta ADCs, a 160-segment LCD driver, 60 KB Flash memory, and 2.5 KB RAM in a 100-pin LQFP (PZ) package. Designed for portable measurement systems, it combines an ultra-low-power 16-bit MSP430 CPU with integrated analog and display resources. An ultra-low-power microcontroller is a semiconductor designed to complete control and measurement tasks while minimizing energy consumption. The MSP430F4793IPZ belongs to the MSP430 family of 16-bit RISC devices and targets battery-powered sensing, electricity metering, and portable instrumentation. Its five low-power operating modes and integrated metering peripherals reduce the need for separate analog, display, and control components. Three sigma-delta ADCs support precision measurement, while the 160-segment LCD controller can drive a segmented display directly. The device includes 60 KB of Flash for firmware and constants, plus 2.5 KB of RAM for working data. A 16 MHz CPU clock provides processing headroom for sampling, calibration, communication, and display management, while operation from 2.5 V to 3.3 V supports common embedded supply rails. The MSP430 architecture uses a 16-bit RISC CPU with 16-bit registers and a constant-memory design suited to low-power portable measurement. Integrating the sigma-delta converters and LCD controller reduces board area and software overhead, but designers must still account for analog input conditioning, reference accuracy, LCD bias requirements, and the power consumed by the display. These considerations are particularly important in designs where sensor accuracy must remain stable over long operating periods. Typical uses include single-phase electricity meters, portable energy monitors, industrial sensing instruments, battery-powered data loggers, and compact equipment with segmented LCD displays. For metering designs, the three ADCs support multiple analog channels, and the 60 KB Flash capacity allows meter constants, calibration tables, and firmware to share one controller. For handheld measurement products, the low-power architecture helps reduce standby consumption and extend battery life. PCB implementation should preserve clean analog routing, provide suitable input filtering, and follow the manufacturer’s pin and layout guidance. The 100-pin LQFP package requires adequate copper and thermal planning, while the LCD and ADC interfaces should be positioned away from high-current switching paths. Firmware should also verify startup behavior, calibration limits, low-power transitions, and display timing before field deployment. This product page combines manufacturer specifications, package information, commercially focused sourcing guidance, and practical selection considerations for engineers designing around the MSP430F4793IPZ. It is intended to support initial design decisions, comparison with related MSP430 devices, and preparation of a qualified bill of materials.

RFQ संपर्क
MSP430F479IPN - 8MHz 16-Bit Sensing MCU | Texas Instruments
MSP430F479IPN

MSP430F479IPN - 8MHz 16-Bit Sensing MCU | Texas Instruments

The Texas Instruments MSP430F479IPN is an 8 MHz, 16-bit RISC sensing microcontroller with 60 KB of flash memory, 2 KB of RAM, one 16-bit Sigma-Delta ADC, a 12-bit DAC, and a 128-segment LCD controller in an 80-pin LQFP package. It combines mixed-signal measurement, programmable LCD drive, and low-power embedded control on a single device. A microcontroller is a programmable semiconductor that executes application software, reads sensors, controls peripherals, and interfaces with a wider electronic system. The MSP430 belongs to the ultra-low-power MCU hierarchy, combining a 16-bit RISC core with mixed-signal peripherals. The MSP430F479 targets instrument, meter, sensor-node, and human-interface applications where measured signals must be converted, displayed, and processed locally. Principal features include 60 KB of program flash configured as 60K × 8 bytes plus 256 bytes, 2 KB of RAM, and 48 I/O pins. Its analog subsystem includes one 16-bit Sigma-Delta ADC and a 12-bit DAC. The integrated 128-segment LCD controller reduces external display-driver requirements, while the 8 MHz CPU supports responsive control and measurement processing. The device operates from -40°C to +85°C and is supplied in an LQFP package with 80 pins. The MSP430 architecture is designed around low-power operation, making the MCU suitable for battery-operated instruments and embedded sensing systems. Analog conversion, LCD multiplexing, general-purpose I/O, and serial communications are integrated around the same CPU. This consolidation can reduce board area and simplify firmware when compared with a system assembled from separate microcontroller, ADC, DAC, and LCD-controller devices. Typical uses include industrial panel meters, portable environmental monitors, laboratory instruments, programmable logic controllers, medical monitoring equipment, and energy-metering products. The LCD controller suits products with segment displays, while the Sigma-Delta ADC supports high-resolution measurement of slowly varying or differential sensor signals. Design around the exact pin assignments, analog input limits, LCD segment mapping, and peripheral multiplexing documented in the Texas Instruments datasheet. Keep analog and LCD routing separated from sensitive timing paths, and verify the external-component values required by the selected reference circuit. This product page combines manufacturer specifications, package details, sourcing guidance, design considerations, and verified drop-in candidates. It also identifies where firmware, board-layout, and qualification checks remain necessary before an MSP430F479IPN is released into production equipment.

RFQ संपर्क
MSP430F5132IDA - 25MHz Mixed-Signal MCU | Texas Instruments
MSP430F5132IDA

MSP430F5132IDA - 25MHz Mixed-Signal MCU | Texas Instruments

Texas Instruments MSP430F5132IDA is a 25 MHz mixed-signal microcontroller with 8 KB flash memory, 1 KB SRAM, a 10-bit ADC, comparator, DMA, and a 16-bit high-resolution timer, housed in a 38-pin TSSOP (DA) package. The industrial-temperature device supports operation from -40°C to +85°C. An MSP430 mixed-signal microcontroller combines a low-power RISC processor, embedded analog conversion, timers, and event-driven peripherals in one device. The MSP430 architecture belongs to the microcontroller hierarchy and is designed for compact embedded systems that must perform control, measurement, and communication functions while minimizing energy use. This integration reduces component count in battery-powered instruments, industrial controls, and sensing equipment. Three principal capabilities define the MSP430F5132IDA. Its 25 MHz CPU provides processing headroom for control algorithms, while 8 KB flash preserves firmware and 1 KB SRAM supports working data. The 10-bit ADC permits direct analog measurement, and the on-chip comparator can support threshold detection and low-power signal monitoring without relying entirely on external converters. The device also integrates DMA and a 16-bit high-resolution timer. DMA can move data between memory and peripherals while the CPU performs other tasks, reducing processing overhead in acquisition and control systems. The high-resolution timer supports precise timing, pulse measurement, and periodic event generation, which are important in metering, motor-control, and industrial automation equipment. Typical uses include sensor nodes, portable measurement instruments, industrial process controls, low-power monitoring equipment, and embedded data-acquisition systems. The combination of local analog conversion, DMA, and 16-bit timing is particularly useful when measurements must be acquired consistently without burdening the main control loop. The 38-pin TSSOP package also supports compact PCB layouts where a large thermal pad would be unnecessary. When designing around this MCU, verify the required analog voltage range and pin multiplexing before assigning ADC or comparator inputs. Place decoupling capacitors close to the supply pins, preserve the intended analog and digital grounding strategy, and confirm programming and debug access on every assembled board. The manufacturer datasheet should govern operating voltages, clock setup, pin multiplexing, and programming-test requirements. This page combines the MSP430F5132IDA ordering information, verified electrical and packaging characteristics, practical design guidance, and qualified same-footprint alternatives. It also distinguishes pin-compatible replacements from functional alternatives that require different packages or peripherals, helping engineers simplify sourcing without overlooking firmware, memory, or analog-interface constraints.

RFQ संपर्क
MSP430F5152IDAR - 25MHz MCU, 16KB Flash, 38-TSSOP | Texas Instruments
MSP430F5152IDAR

MSP430F5152IDAR - 25MHz MCU, 16KB Flash, 38-TSSOP | Texas Instruments

The Texas Instruments MSP430F5152IDAR is a 16-bit mixed-signal microcontroller with 16KB Flash, 2KB SRAM, a 25 MHz CPU, 10-bit ADC, comparator, DMA, and a 16-bit High-Resolution timer, housed in a 38-pin TSSOP (DA) package rated for the industrial -40C to +85C range. The CPU executes the MSP430 RISC instruction set at up to 25 MIPS, and five low-power modes (LPM0-LPM4) keep active-mode current to roughly 180 uA/MHz and standby current in the single-digit microamp range, which is the core value proposition of the MSP430 family. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory, data memory, and configurable peripherals on a single silicon die. The MSP430 architecture belongs to the 16-bit RISC microcontroller hierarchy, sits under the broader class of embedded microcontrollers, and is widely used in ultra-low-power applications where battery life and standby current dominate the design trade-off. Within TI's portfolio, the F5xx series targets mixed-signal measurement and motor-control applications, distinguishing it from the F1xx/F2xx general-purpose and F6xx LCD-driver families. Key features of the MSP430F5152 include the integrated 10-bit SAR ADC with sample-and-hold, an analog comparator, a 16-bit High-Resolution Timer (HRT) suitable for precision timing and capture, a 4-channel DMA controller, and up to 31 general-purpose I/O pins. The supply range is 2.4V to 3.6V, an internal oscillator supports low-cost clocking, and the part supports JTAG and Spy-Bi-Wire (2-wire JTAG) in-system programming and debug. Technically, the device combines a 16-bit RISC core, on-chip Flash, on-chip SRAM, and a flexible clock system with multiple internal DCO and VLO sources plus external crystal support. The DMA engine offloads peripheral-to-memory transfers, allowing the CPU to remain in a low-power mode during data acquisition - a key enabler for battery-powered sensor nodes. Typical applications include portable instrumentation, energy-harvesting sensor nodes, smart metering, motor control, low-end medical devices, and battery-powered industrial sensor hubs where the 16-bit HRT improves timing resolution. The TSSOP-38 footprint is friendly to hand-solder prototypes and compact production PCBs alike. When designing with the MSP430F5152, leave adequate ground copper near the exposed pad area to support the device's low-noise analog blocks, and ensure the AVCC/AVSS pair is filtered with a ferrite bead if the ADC and digital I/O coexist on the same rail. This page synthesizes current distributor pricing, verified drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for sourcing and qualifying the MSP430F5152IDAR.

RFQ संपर्क