उत्पाद (44,000+)

MX30LF1GE8AB-TI-TR - 1Gbit 3V SLC NAND Flash, x8, TSOP-48 | Macronix
MX30LF1GE8AB-TI-TR

MX30LF1GE8AB-TI-TR - 1Gbit 3V SLC NAND Flash, x8, TSOP-48 | Macronix

The Macronix MX30LF1GE8AB-TI-TR is a 1 Gbit (128 M x 8) 3 V Single-Level Cell (SLC) parallel NAND Flash memory device housed in a 48-pin TSOP-I (Type I) package, supplied on tape-and-reel. It is ONFI 1.0 compliant, supports a parallel asynchronous interface with 20 ns / 25 ns access time depending on grade, and operates from a single 2.7 V to 3.6 V supply with an ECC-Free architecture intended for use with an external host controller. A NAND Flash is a non-volatile memory that stores data as charge on floating-gate cells arranged in pages and blocks, accessed through a command-driven protocol over a multiplexed 8-bit I/O bus. SLC NAND stores one bit per cell, offering the highest endurance and reliability within the NAND family (which itself is a class of non-volatile memory -> flash memory -> semiconductor memory -> IC). Compared with NOR flash, NAND provides higher density at lower cost-per-bit and faster write/erase, but requires sequential access and external ECC for data integrity in mission-critical applications. Key features include a 2112-byte page size (2048 + 64 spare), 64 pages per block (128 KB + 4 KB spare), 1024 blocks, internal data-move / copy-back operations, hardware-ready/busy (R/B#) signaling, and command-set compatibility with the ONFI 1.0 baseline. ECC-Free means error correction is handled by the host, giving designers freedom to choose ECC strength (typically BCH or Hamming). The TSOP-I 48-pin package is the industry-standard footprint shared by most 1 Gbit to 4 Gbit parallel NAND parts. The MX30LF1GE8AB architecture uses a 2-plane array that enables interleaved page program and block erase between planes for higher throughput. Plane interleaving can effectively double sequential write bandwidth by overlapping tPROG of one plane with tR of the other. Designers should size VCC decoupling (1 uF + 100 nF) close to the VCC/VSS pins and respect the 100 us R/B# power-on delay per the Macronix datasheet revision v1.3. Typical applications include embedded Linux/OS boot + mass storage in industrial gateways, set-top box and smart-TV storage, automotive infotainment (non-safety), networking equipment logging, and IoT edge devices that need reliable code + data storage at 3 V. Designers migrating from the older MX30LF1G08AA should review Macronix application note AN0366V1, as the MX30LF1GE8AB has a longer Device ID and slightly longer tR. When designing in this part, allow 1.5 us tRST after power-up before issuing the reset (0xFF) command. The R/B# pin is open-drain and requires an external pull-up. For long-term data retention, program/erase endurance is rated at 100 K cycles per block typical, with 10-year data retention. This page synthesizes distributor pricing, drop-in and same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
MX30LF1GE8AB-XKI-TR - 1Gbit 3V SLC NAND Flash, 63-VFBGA | Macronix
MX30LF1GE8AB-XKI-TR

MX30LF1GE8AB-XKI-TR - 1Gbit 3V SLC NAND Flash, 63-VFBGA | Macronix

The Macronix MX30LF1GE8AB-XKI-TR is a 1 Gbit (128M x 8) 3V SLC NAND Flash memory organized as parallel x8 in a 63-ball VFBGA (9x11 mm) package. It supports an asynchronous parallel interface with a 20 ns initial access time and operates from a single 2.7V to 3.6V supply, with a typical active current of 15 mA. The device is ONFI 1.0 compliant and is supplied in Tape & Reel packaging for high-volume SMT production. A NAND Flash memory is a non-volatile storage technology that retains data without power, using floating-gate transistors arranged in NAND string blocks and pages. It sits in the hierarchy between raw NOR (byte-addressable, fast read) and managed NAND/eMMC (controller-integrated). SLC (Single-Level Cell) NAND stores one bit per cell, giving it the highest endurance and reliability tier in the NAND family - typically 100K P/E cycles per block versus 3K-10K for MLC/TLC - making it preferred for industrial code storage, boot media, and high-write workloads where MLC/TLC would wear out quickly. The MX30LF1GE8AB family features a 2,112-byte page (2,048 bytes data + 64 bytes spare for bad-block marks and ECC), 64 pages per block, and 1,024 blocks per plane. Program and erase times are 1 ms (typical) page-program and 2 ms block-erase, while page-read cycle time is on the order of 25 ns. ECC handling is left to the host controller, which is why this family is labelled ECC-Free. Typical applications include industrial embedded systems, networking equipment, set-top boxes, printers, and automotive infotainment where 1 Gbit of non-volatile code or data storage is needed with parallel access. The wide -40C to +85C operating range covers industrial environments, and the small 9x11 mm VFBGA footprint suits space-constrained PCB designs. When migrating a design to the MX30LF1GE8AB, ensure the host controller supports the longer Device ID and tR random read cycle compared with the legacy MX30LF1G08AA, per Macronix application note AN0366. Add external ECC in the controller firmware, since this part ships ECC-Free. This page synthesizes distributor pricing, drop-in alternatives in the same 63-VFBGA footprint, and practical design notes not collected in the manufacturer datasheet.

RFQ संपर्क
MX30LF4G18AC-TI-T - 4Gbit SLC NAND Flash, 3V, TSOP-48 | Macronix
MX30LF4G18AC-TI-T

MX30LF4G18AC-TI-T - 4Gbit SLC NAND Flash, 3V, TSOP-48 | Macronix

The Macronix MX30LF4G18AC-TI-T is a 4 Gbit SLC NAND Flash memory IC organized as 512M x 8 bits, housed in a 48-pin TSOP-I (12 mm x 20 mm) package. Operating from a 2.7V to 3.6V single supply with a 20 ns random access time, it delivers high endurance and reliability for code and data storage in embedded designs. The part supports a parallel asynchronous interface compliant with the ONFI 1.0 standard and is offered in a -40C to +85C industrial temperature grade. An SLC (Single-Level Cell) NAND Flash is a non-volatile memory technology that stores one bit per memory cell, providing higher write endurance (typically 60k-100k P/E cycles), faster write performance, and lower bit error rates than MLC or TLC NAND. SLC NAND sits below raw NAND in the storage hierarchy - between NOR Flash (byte-addressable, slower write) and managed NAND (eMMC/UFS with built-in controllers). Because raw SLC NAND requires an external Flash controller (or FTL in software), it is favored in cost-sensitive, reliability-critical designs where the host MCU or ASIC already includes a NAND controller. Key features of the MX30LF4G18AC-TI-T include a 20 ns access time, ONFI 1.0 parameter page compatibility, 4-bit ECC requirement per 528-byte sector, 8-bit data bus, and a 10-year data retention rating. The device supports single-plane and dual-plane operations, hardware data protection via WP#, and a standard command set (read, program, erase, block management) consistent with the ONFI 1.0 specification. The wide temperature operating range (-40C to +85C) suits industrial and automotive-adjacent applications. At the architectural level, the device is organized into 4096 blocks of 128 KB plus spare area, with each page holding 2 KB + 64 B spare (x8 mode). Page program is typically 300 us and block erase around 2 ms, enabling deterministic write timing for industrial firmware updates and fast boot storage. The 4-bit ECC requirement means the system controller must implement a BCH or Reed-Solomon engine to correct raw bit errors before they exceed the ECC budget. Typical applications include industrial embedded Linux systems, automotive infotainment boot media, networking equipment firmware storage, factory automation controllers, and ruggedized IoT gateways that demand long-term reliability under wide temperature swings. When designing with raw NAND, ensure the host controller implements 4-bit ECC per 528-byte sector, plan for bad-block management in software, and reserve enough boot time for NAND initialization. The TSOP-48 footprint is widely supported by surface-mount assembly lines but requires careful PCB layout to keep the 8-bit parallel bus impedance-controlled for signal integrity at 20 ns access speeds. This page synthesizes distributor pricing, same-brand density/package variants, and practical ECC and layout design notes not consolidated in any single manufacturer or distributor source.

RFQ संपर्क
MX30LF4G18AC-XKI-T - 4Gbit SLC NAND Flash 63-VFBGA | Macronix
MX30LF4G18AC-XKI-T

MX30LF4G18AC-XKI-T - 4Gbit SLC NAND Flash 63-VFBGA | Macronix

The Macronix MX30LF4G18AC-XKI-T is a 4 Gbit parallel SLC NAND Flash memory organized as 512M x 8 bits, housed in a 63-ball 9x11 mm VFBGA package (also known as 63-VFBGA / BGA-63). It operates from a single 3V supply (2.7V to 3.6V), supports ONFI 1.0 timing, and offers a 20 ns access time, making it well-suited for boot, code, and data storage in embedded designs. The -XKI suffix indicates the industrial operating-temperature grade of -40C to +85C, while the -T suffix denotes Tape & Reel packaging for high-volume SMT assembly. NAND Flash is a non-volatile storage technology where memory cells are arranged in strings and pages rather than as individually addressable bytes. SLC (Single-Level Cell) stores one bit per cell, giving higher endurance, faster write speeds, and better data retention than MLC/TLC alternatives. The MX30LF4G18AC belongs to Macronix's MX30LF family of 3V SLC NAND devices and uses an asynchronous parallel interface to a host controller. Within the broader taxonomy, it sits under Flash Memory -> Non-Volatile Memory -> Memory IC -> Semiconductor. Compared with NOR Flash, NAND provides higher density at lower cost-per-bit but requires a controller to manage bad blocks, wear leveling, and ECC, which is why this part mandates 4-bit ECC per 528 bytes. Key specifications include a 2,048-byte main page area plus a 64-byte spare area per page (2,112 bytes total), 64 pages per block, and an internal data buffer of 2,112 bytes for load and access. The device is divided into two planes, each composed of NAND strings of 32 serially connected cells, which enables interleaved page operations for higher throughput. ONFI 1.0 compliance guarantees standardized command sets, timing parameters, and feature registers across compliant hosts. Typical applications include embedded Linux/Android boot storage, solid-state drives (SSD) for SATA/USB bridges, automotive infotainment, set-top boxes, industrial gateways, and IoT edge nodes. Designers favor this Macronix SLC part where 100,000 P/E cycle endurance and 10-year data retention matter more than the highest densities available from MLC/TLC devices. When designing in the MX30LF4G18AC-XKI-T, allocate sufficient host-side ECC (4-bit per 528 bytes minimum), place a 0.1uF decoupling capacitor close to the VCC ball, and respect the 20 ns tRC/tWC timing budget. The 9x11 mm VFBGA footprint is compact, but its 0.8 mm pitch demands 4-layer PCB with microvia or laser-drilled vias for reliable manufacturing.

RFQ संपर्क
MX30LF4G18AC-XKS-T - 4Gbit 3V SLC NAND Flash BGA-63 | Macronix
MX30LF4G18AC-XKS-T

MX30LF4G18AC-XKS-T - 4Gbit 3V SLC NAND Flash BGA-63 | Macronix

The Macronix MX30LF4G18AC-XKS-T is a 4 Gbit (512 M x 8) 3 V SLC NAND Flash memory in a 63-ball VFBGA (9 x 11 mm) package, qualified to +85C for automotive-grade applications. It features a parallel x8 interface with a typical 20 ns access time, 4-bit ECC requirement per 512 bytes, and ONFI 1.0 compliance for command-set interoperability. The device organizes 4 Gbits into two planes of 2,048-byte pages with 64 spare bytes each, totaling 2,112 bytes per page; the on-chip buffer matches the page size for load/program operations. An SLC (Single-Level Cell) NAND Flash is a non-volatile memory that stores one bit per cell, offering higher endurance, faster write speeds, and lower bit error rates than MLC/TLC NAND at the cost of lower density per die. SLC belongs to the broader NAND Flash family, which in turn is a subset of non-volatile memory technologies (Flash, EEPROM, FRAM, MRAM) used for code and data storage in embedded systems. SLC NAND's role in the memory hierarchy is to provide persistent, block-addressable storage between DRAM (volatile, fast) and serial NOR Flash (random-access, lower density), making it ideal for OS images, file systems, and data logging. Key features of the MX30LF4G18AC-XKS-T include a wide 2.7 V to 3.6 V single-supply operating range, 4-bit ECC per 528 bytes for robust data integrity, 100K program/erase cycles endurance per block, and 10-year data retention. The device supports standard NAND commands (Read, Program, Erase, Status) plus ONFI-defined parameter page reads, easing firmware development. Internal data-move and copy-back operations accelerate block management without external bus traffic. The architecture uses a two-plane structure with 64 pages of (2,048 + 64) bytes per plane, organized as two NAND strings of 32 series-connected cells. The 63-ball VFBGA footprint (9 x 11 mm) suits space-constrained designs, and the -XKS suffix denotes tape-and-reel packaging with an industrial/automotive +85C operating temperature grade. Designers should ensure 4-bit ECC is implemented in the host controller, as the device does not include an internal ECC engine. Typical applications include automotive infotainment and telematics, industrial gateways, IoT edge nodes, point-of-sale terminals, and firmware boot media. In automotive dashboards the part stores navigation maps and OS images; in IoT gateways it logs sensor telemetry. Compared with SPI NOR Flash of similar density, this SLC NAND delivers higher capacity at lower cost-per-bit but requires block-level management and ECC, increasing firmware complexity. The -XKS-T suffix adds tape-and-reel packaging for high-volume SMT assembly lines. When designing with this part, allocate one NAND controller pin set (ALE, CLE, WE#, RE#, CE#) and route I/O[7:0] as an 8-bit parallel bus. Place 0.1 uF decoupling near VCC balls and keep the 8-bit bus length-matched within 50 mils. The 4-bit ECC per 528 bytes must be generated by the host MCU/SoC; Macronix does not embed the ECC engine on this die.

RFQ संपर्क
MX30LF4G28AB - 4Gbit SLC NAND Flash, 3V Parallel | Macronix
MX30LF4G28AB

MX30LF4G28AB - 4Gbit SLC NAND Flash, 3V Parallel | Macronix

The Macronix MX30LF4G28AB is a 4 Gbit (512M x 8) SLC NAND Flash memory with a parallel asynchronous interface, designed for low-density non-volatile storage in industrial, networking, and consumer embedded designs. It operates from a 2.7 V to 3.6 V supply and delivers 20 ns random access time in industry-standard 48-pin TSOP-I and 63-ball VFBGA packages. The device is ONFI 1.0 compliant, ensuring standardized command set, timing, and status register behavior for software portability across vendors. SLC (Single-Level Cell) NAND Flash is a non-volatile memory technology that stores one bit per memory cell, providing higher endurance (typically 60,000 to 100,000 program/erase cycles), faster write throughput, and longer data retention than MLC or TLC NAND. SLC NAND sits in the hierarchy: NAND Flash -> non-volatile memory -> memory IC -> semiconductor. It is commonly used where reliability, deterministic write performance, and wide-temperature operation outweigh the bit-density advantages of MLC/TLC parts. The MX30LF4G28AB divides its array into two planes, with 64 pages of (2,048+112) bytes per page, providing a 2,160-byte on-chip data register for page read, program, and cache operations. Key features include hardware data protection via the WP# pin, a Ready/Busy (R/B#) open-drain status output, ONFI-compliant unique ID read, and status register read. The page size of 2,048 bytes plus 112 bytes of spare area per page allows the host to apply ECC (typically BCH or Hamming) for bit-error correction without sacrificing user data capacity. The 48-TSOP-I package is backward-compatible with the 48-TSOP footprint used by many 2 Gb and 4 Gb parallel NAND parts, easing migration from older designs. Typical applications include industrial routers and gateways, factory automation controllers, automotive infotainment and instrument clusters, set-top box boot/media storage, point-of-sale terminals, and IoT edge devices. The wide -40 C to +85 C industrial operating range and ONFI compliance make it a fit for designs that require predictable behavior across temperature and across vendor sourcing. When designing with this device, allow margin for program/erase wear by implementing a wear-leveling algorithm and a robust ECC scheme (BCH-4 or stronger is recommended for 3x nm-class die). Decoupling: place a 0.1 uF and a 4.7 uF ceramic capacitor close to VCC/VCCQ, and route R/B# as an open-drain signal with a pull-up resistor to VCCQ to avoid in-rush current glitches. This page synthesizes distributor pricing, drop-in and cross-brand equivalents documented in Macronix application notes AN0280V2 (vs Spansion S34ML04G200) and AN0281V2 (vs Spansion S34ML04G100), and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MX30LF4GE8AB - 4Gbit SLC NAND Flash, 3V, Parallel | Macronix
MX30LF4GE8AB

MX30LF4GE8AB - 4Gbit SLC NAND Flash, 3V, Parallel | Macronix

The Macronix MX30LF4GE8AB is a 4 Gbit (512 M x 8) 3V SLC NAND Flash memory device organized as 2048 blocks of 64 pages with 2112 bytes per page, housed in a 48-pin TSOP type-I (48-TSOP) package. It is compliant with the ONFI 1.0 standard and delivers a parallel asynchronous interface with 20 ns access time, making it a drop-in compatible member of the MX30LF/MX60LF 3V SLC NAND families. The device operates from a single 2.7V to 3.6V supply and supports an industrial-grade temperature range for embedded and harsh-environment use. SLC (Single-Level Cell) NAND is a non-volatile memory technology in which each memory cell stores one bit. In the broader semiconductor taxonomy, SLC NAND sits under NAND Flash, which is a category of flash memory, which is itself a type of non-volatile memory, sitting alongside NOR Flash, EEPROM, and FRAM. Unlike NOR Flash, NAND Flash is optimized for high-density sequential read/write and is typically managed by an external controller with software like a Flash Translation Layer (FTL). SLC specifically offers the highest endurance (typically 60k-100k P/E cycles), lowest bit error rate, and longest data retention (10 years) of any NAND technology, at the cost of lower density per die compared to MLC/TLC/QLC. Key features of the MX30LF4GE8AB include an internal 2112-byte page register for cache operations, a multiplexed 8-bit I/O bus (data and commands share the bus), hardware ECC support via the chip, dedicated CE# and WP# pins for array protection, and a dedicated R/B# (Ready/Busy) open-drain output for status polling. The device integrates an on-chip page buffer that lets the host read the next page while the current page is being output, increasing sequential read throughput. Built-in block erase is supported at the 64-page block granularity (128 KB + spare area). The architecture is conventional NAND with a command-driven interface: addresses are latched across multiple bus cycles, and commands like 0x00/0x30 (Read), 0x80/0x10 (Page Program), and 0x60/0xD0 (Block Erase) are issued via the CLE/ALE strobes. The MX30LF4GE8AB targets applications where reliability, longevity, and simple hardware integration outweigh density-per-cost, distinguishing it from MLC/TLC parts that need stronger controllers. The 20 ns access time is competitive for industrial-grade 3V NAND, allowing 40 MHz+ bus operation. Typical applications include automotive infotainment and instrument clusters, networking routers and PON/ONU optical modules, factory automation controllers, set-top box firmware storage, and industrial-grade data loggers. The wide 2.7V-3.6V VCC tolerance allows operation directly from a 3.3V system rail and is robust against typical 3.3V supply transients. When designing with the MX30LF4GE8AB, allocate sufficient processor I/O pins for the multiplexed 8-bit bus plus control signals (CLE, ALE, CE#, RE#, WE#, WP#, R/B#). Plan for bad-block management in firmware - SLC blocks are reliable but a small percentage are factory-marked bad at shipment, and ECC should correct at least 1-bit per 528 bytes. This page synthesizes distributor pricing, drop-in alternatives, and design notes that supplement the Macronix datasheet with practical sourcing context.

RFQ संपर्क
MX30UF1G16AC - 1Gb 1.8V SLC NAND Flash, 48-VFBGA | Macronix
MX30UF1G16AC

MX30UF1G16AC - 1Gb 1.8V SLC NAND Flash, 48-VFBGA | Macronix

The Macronix MX30UF1G16AC is a 1 Gbit 1.8 V SLC NAND Flash memory organized as 64M x 16 bits in a 48-VFBGA (6x8 mm) package, with a parallel asynchronous interface and 25 ns access time. It is part of Macronix's MX30UF family of low-voltage, high-reliability SLC NAND devices, and is offered in multiple density x16/x8 options. A NAND Flash memory is a non-volatile storage technology that retains data without power using floating-gate memory cells arranged in NAND strings (series-connected cells per bitline), delivering high density at low cost per bit. SLC (Single-Level Cell) stores 1 bit per cell, giving the MX30UF1G16AC superior endurance (typically 100K P/E cycles), faster write performance, and 10-year data retention compared with MLC/TLC counterparts. Within the broader taxonomy, this device sits at NAND Flash -> Flash Memory -> Non-Volatile Memory -> Memory IC -> Semiconductor, and is frequently benchmarked against ONFI 1.0-compatible parallel NAND from other vendors. Key features of the MX30UF1G16AC include 1.7 V to 1.95 V single supply operation, 25 ns access time, word/page write cycle time of 25 ns, industrial temperature range of -40C to +85C, and 10-year data retention. The part supports a standard NAND command set, offers hardware data protection, and integrates an internal page buffer to streamline sequential read/write operations. Multiple package options (48-VFBGA, 48-TSOP I, 63-ball BGA 9x11 mm) and a separate x8 variant (MX30UF1G18AC) provide designers with footprint flexibility. Designed primarily for code storage and data logging in cost-sensitive embedded systems, the MX30UF1G16AC trades the higher density of managed eMMC for BOM simplicity and direct host-side control, which matters in industrial HMI, networking line cards, and boot/auxiliary storage where the host processor already implements the flash controller. Typical applications include boot ROM/disk-on-chip for set-top boxes and routers, firmware/data storage in industrial PLCs, datalogging for metering and telemetry, automotive infotainment auxiliary storage (with system-level derating), and SSD bridging where a controller is bonded to raw NAND. The MX30UF1G16AC is supported by Macronix reference controller firmware and ONFI 1.0 software drivers; designers should implement ECC (typically 8-bit per 528 bytes) and bad-block management at the host, as on-die ECC is not included on this part family.

RFQ संपर्क
MX30UF1G18AC-TI-T - 1.8V 1Gb SLC NAND Flash TSOP-48 | Macronix
MX30UF1G18AC-TI-T

MX30UF1G18AC-TI-T - 1.8V 1Gb SLC NAND Flash TSOP-48 | Macronix

The Macronix MX30UF1G18AC-TI-T is a 1.8V, 1 Gbit (128 MB x 8 / 64 MB x 16) SLC NAND Flash memory delivered in a 48-pin TSOP-I (12 mm x 20 mm) package, compliant with the ONFI 1.0 standard. It features a parallel x8/x16 data interface with 4-bit ECC per 512 bytes, asynchronous NAND command set, and a 10-year data retention rating with industrial-grade endurance of 100,000 program/erase cycles per block. As a member of the SLC (Single-Level Cell) NAND Flash family, the MX30UF1G18AC-TI-T provides the highest endurance and lowest bit-error rate among NAND technologies, distinguishing it from MLC, TLC, and QLC alternatives. SLC stores one bit per cell, eliminating the multi-level voltage-threshold challenges of denser NAND and delivering typically 10x the endurance of MLC. It belongs to Macronix's 1.8V MX30UF series, complementing the 3V MX30LF and MX60LF lines for systems with mixed-voltage rails, and serves the role of non-volatile code-and-data storage in embedded designs. Key features include a wide operating supply of 1.7V to 1.95V (1.8V nominal), standard asynchronous NAND timing with a tR/tPROG access window of 25 ns typical, an internal data register for page buffer operations, and hardware block-protection capability via WP#/HOLD# multifunction pins. The 48-TSOP-I package supports both x8 (8-bit) and x16 (16-bit) I/O configurations selectable at power-up by the ALE/CLE command sequence. Architecturally, the device integrates a charge-pump high-voltage generator for program/erase, an on-chip temperature-compensated reference, and a 2048-byte (x8) / 1024-word (x16) page register for read/program buffering. ONFI 1.0 parameter-page interrogation enables host controllers to query geometry, timing, and ECC requirements at boot, simplifying firmware bring-up in Linux and RTOS environments that include native NAND drivers. Typical applications include set-top box firmware storage, industrial HMI panel code/asset storage, point-of-sale terminals, automotive infotainment boot media (non-safety-critical), networking switch configuration memory, and Linux-based IoT gateways requiring robust embedded file systems such as UBIFS or JFFS2. Designers choose this part for high write-endurance logging and predictable read latencies rather than raw density. When designing with this device, verify that the host controller provides a sufficient VCCQ rail at 1.8V (not 3.3V) and reserves dedicated GPIO for WP#, HOLD#, RE#, WE#, and ALE/CLE. Implementation of 4-bit ECC per 512-byte sector using BCH or Hamming software/HW codecs is mandatory; uncorrectable NAND typically causes boot failure or silent data corruption in journaled filesystems. This page consolidates distributor pricing as of 2026-10-15, drop-in pin-compatible same-package alternatives, practical design guidance, and 4-bit ECC architectural notes not found in the Macronix datasheet summary alone.

RFQ संपर्क
MX30UF1G18AC-XKI-T - 1Gb SLC NAND Flash 1.8V Parallel | Macronix
MX30UF1G18AC-XKI-T

MX30UF1G18AC-XKI-T - 1Gb SLC NAND Flash 1.8V Parallel | Macronix

The Macronix MX30UF1G18AC-XKI-T is a 1-Gbit SLC NAND Flash memory from the MX30UF family, offering 1.8V operation, x8 parallel interface, and 25 ns access time in a 63-ball VFBGA (9 mm x 11 mm) package. The device supports 4-bit ECC and is supplied on Tape & Reel for high-volume SMT assembly. Densities of 1 Gbit, configured as 128M x 8, deliver the basic data/code storage building block in low-density 1.8V systems where reliability, data retention, and industrial temperature operation are critical. An SLC NAND Flash is a type of non-volatile memory that stores 1 bit per cell, providing higher endurance (typically 100K P/E cycles per block) and better data retention compared to MLC and TLC NAND. In the broader taxonomy, it belongs to NAND flash memory -> flash memory -> non-volatile memory -> semiconductor memory. SLC NAND occupies the high-reliability tier of NAND technology and is preferred over NOR for high-density data storage where read throughput and cost-per-bit dominate the requirement. The MX30UF family specifically targets 1.8V systems, which reduces power consumption by roughly 40% compared to equivalent 3V parts (Macronix MX30LF/MX60LF) and simplifies power-rail count in battery-powered designs. Key features of the MX30UF1G18AC-XKI-T include a wide 1.7V-to-1.95V operating voltage window, 4-bit on-die or controller-side ECC support, an industrial temperature range of -40C to +85C, 10-year data retention, and an 8-bit (x8) parallel asynchronous data bus. The 25 ns access time enables sequential read throughput in the tens of MB/s range when paired with a controller that supports page-mode operation. The VFBGA-63 footprint (9 mm x 11 mm, 0.8 mm ball pitch, 1 mm height) is a JEDEC-standard layout. The device uses a single-transistor floating-gate cell with a standard NAND string architecture. Internally, the memory is organized into multiple planes and blocks, and the device exposes standard NAND command set operations (page read, page program, block erase, copy-back). Hardware controllers from Macronix or third parties can use the part as a drop-in SLC NAND source. Power-on auto-read of the first page supports boot-from-NAND use cases on small microprocessors. Typical applications include firmware and data logging in industrial IoT gateways, automotive infotainment and telemetry, smart-home edge nodes requiring small reliable non-volatile storage, networking equipment such as DSL/cable modems and routers, and portable medical devices where low 1.8V power is essential. The wide temperature range also fits factory-automation HMIs and outdoor asset-tracking modules. When designing with this part, ensure that the chosen NAND controller supports 4-bit ECC, since the device does not include an on-die ECC engine. Decoupling caps close to VCC balls and a clean 1.8V supply reduce read/program disturbs. Page-size, block-size, and OOB-area geometry must match the controller's translation layer expectations. This page synthesizes distributor stock, drop-in alternatives, and practical design notes not found on the manufacturer product page alone.

RFQ संपर्क
MX30UF1G18AC-XKI-TR - 1Gbit 1.8V SLC NAND Flash | Macronix
MX30UF1G18AC-XKI-TR

MX30UF1G18AC-XKI-TR - 1Gbit 1.8V SLC NAND Flash | Macronix

The Macronix MX30UF1G18AC-XKI-TR is a 1 Gbit (128 M x 8) Single-Level Cell (SLC) parallel NAND Flash memory operating from a 1.8 V supply, housed in a 63-ball 9 mm x 11 mm VFBGA (VFBGA-63) package. Per the Macronix datasheet, the part offers 25 ns initial access time, ONFI 1.0-compatible command set, an integrated 4-bit ECC engine, and 100,000 program/erase cycles per block with 10-year data retention. NAND Flash memory is a type of non-volatile storage that retains data when power is removed. Within the storage hierarchy it sits below DRAM in cost-per-bit but offers far higher density and endurance than NOR Flash. SLC stores one bit per cell, trading density for the highest endurance and reliability of any NAND technology. The MX30UF1G18AC-XKI-TR belongs to the MX30UF family of 1.8 V SLC NAND parts that complement Macronix's parallel and serial NOR Flash portfolio, targeting code and data storage in embedded systems. Key features include a parallel (asynchronous) x8 I/O interface with multiplexed address and data, hardware-ready 4-bit ECC for single-bit correction within each 528-byte page, and an ONFI 1.0-compliant command set that simplifies firmware development across density migrations. The 1.8 V core supply enables direct connection to low-voltage SoCs without level shifters, and the small 9 mm x 11 mm VFBGA footprint suits space-constrained designs such as wearables, IoT edge nodes, and SSD cache modules. The architecture is based on a NAND array organized as 128 M x 8 with page sizes of 2,112 bytes (2,048 main + 64 spare) and 64 pages per block. The internal 4-bit ECC engine corrects single-bit errors in real time, dramatically reducing host MCU bandwidth and firmware complexity for bad-block management. The interface uses an 8-bit bidirectional data bus with standard NAND control signals (CE, RE, WE, ALE, CLE) and a busy/ready status pin. Typical applications include Linux boot and rootfs storage on ARM-based SoCs in industrial gateways, IoT edge devices, networking equipment, automotive infotainment, and POS terminals where ONFI-standard drivers and SLC reliability are required. The wide temperature operation also supports outdoor and industrial installations. When designing with this part, ensure the host controller supports the ONFI 1.0 command set or implements a software NAND driver. A minimum of one external 1.8 V decoupling cap per power pin plus proper signal integrity on the parallel bus are essential for reliable operation. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MX30UF4G16AB - 4Gbit 1.8V SLC NAND Flash, Parallel x16 | Macronix
MX30UF4G16AB

MX30UF4G16AB - 4Gbit 1.8V SLC NAND Flash, Parallel x16 | Macronix

The Macronix MX30UF4G16AB is a 4 Gbit (512 MB) 1.8 V SLC NAND flash memory organized as 256 M x 16 in a 63-ball 9 mm x 11 mm VFBGA package with 25 ns access time and ONFI 1.0 compatibility. It is part of the Macronix MX30UF family of low-density SLC NAND devices designed for embedded systems that demand high endurance, predictable latency, and long-term data retention without the controller complexity of MLC or TLC alternatives. A NAND flash is a non-volatile memory that stores data as charge on floating-gate transistors arranged in NAND strings, providing the lowest cost-per-bit of any rewritable semiconductor memory. SLC (Single-Level Cell) variants, like the MX30UF4G16AB, store one bit per cell, yielding the best endurance (typically 60k-100k P/E cycles), fastest write throughput, and lowest bit-error rate. Within the broader taxonomy, SLC NAND sits below NOR flash in random read speed but dominates in density and sequential write cost, making it the workhorse for data logging, OS image storage, and boot media in industrial, automotive, and consumer embedded designs. Key features of the MX30UF4G16AB include 4 Gbit density in a x16 parallel interface, 1.7 V to 1.95 V single supply operation, 50 uA (max) standby current in Sleep Mode, ONFI 1.0 parameter page support for standardized identification, and 25 ns asynchronous page read access. The 63-ball VFBGA (9x11 mm) footprint is shared with the Macronix MX30LF family of 3 V parts, easing layout migration between 1.8 V and 3.0 V system rails. Hardware ECC and bad-block management are handled externally by the host controller, consistent with raw NAND conventions. Architecturally, the MX30UF4G16AB uses a single-plane array with a 2 KB page size and 64 KB block erase granularity, accessed through an 8/16-bit multiplexed address/data bus. The command set follows the standard ONFI NAND interface, with CLE, ALE, CE#, RE#, WE#, WP#, and R/B# pins enabling tight integration with common NAND controllers from NXP, TI, Microchip, and Allwinner. The device supports multi-plane read for higher sequential throughput. Typical applications include industrial data loggers, eMMC alternative boot media for Linux/Android systems, automotive infotainment firmware storage, IoT edge devices requiring local buffering, point-of-sale terminals, and consumer electronics such as set-top boxes and Wi-Fi routers where the system designer prefers a managed raw NAND over an eMMC module. The wide operating temperature range and SLC endurance make it suitable for harsh-environment designs. One key design consideration is that raw NAND requires the host CPU or controller to perform wear-leveling, bad-block management, and ECC (typically BCH or LDPC). Engineers migrating from serial NOR flash should plan for an additional 4-8 KB of boot ROM or a small filesystem such as UBI/YAFFS to manage the device. Pin count is generous at 63 balls, so PCB escape routing requires a 4-6 layer stack-up with microvia-in-pad for high-density designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, making it useful for sourcing engineers, BOM managers, and firmware developers evaluating 1.8 V SLC NAND options.

RFQ संपर्क
MX30UF4G18AB - 4Gbit 1.8V SLC NAND Flash, 48-TSOP | Macronix
MX30UF4G18AB

MX30UF4G18AB - 4Gbit 1.8V SLC NAND Flash, 48-TSOP | Macronix

The Macronix MX30UF4G18AB is a 4 Gbit (4 Gbit = 512 MiB = 4,096 Mbit of raw NAND storage, organized as 2,048 blocks x 64 pages x 4,096 bytes + spare) 1.8 V single-level cell (SLC) parallel NAND Flash memory in a 48-pin TSOP package, with 25 ns asynchronous page read access time. It is part of the MX30UF 1.8V SLC NAND family, designed for code and data storage in space-constrained, low-power embedded systems. An SLC NAND Flash is a type of non-volatile memory that stores one bit per cell, providing higher endurance (typically 60,000 to 100,000 P/E cycles per block), faster write throughput, and lower bit error rates compared to MLC or TLC NAND. In a system hierarchy it sits as: SLC NAND -> NAND Flash -> non-volatile memory -> semiconductor memory. SLC NAND is commonly chosen over NOR Flash when higher density at lower cost-per-bit is required and a controller (e.g., an eMMC host or raw NAND controller in an SoC) is available to handle bad-block management and ECC. Key features of the MX30UF4G18AB include a 1.8V VCC operation (1.7V to 1.95V range per Macronix datasheet v1.2), a 50 uA maximum standby current in sleep mode, ONFI 1.0-compatible command set, 8-bit I/O bus, and integrated page buffer of 4,320 bytes (4,096 main + 224 spare). The device supports a 528-byte page size with spare area (legacy x8 mode) or a 4,320-byte page in ONFI mode, with multi-plane programming for higher write throughput. Architecturally, the MX30UF4G18AB uses a charge-trap or floating-gate SLC cell array, an internal charge pump to generate high programming voltages from a single 1.8V supply, and an ONFI 1.0-compliant state machine that exposes standard commands (Read, Page Program, Block Erase, Read Status, Read ID, Reset). The 8-bit asynchronous interface makes it compatible with most SoC NAND controllers without glue logic. Typical applications include boot storage in set-top boxes, data logging in industrial IoT sensor nodes, firmware and asset tracking in wearables, and Linux/embedded OS rootfs storage in 1.8V SoCs. Designers choose this part when they need reliable SLC endurance at low power and small form factor. When designing with the MX30UF4G18AB, allocate a minimum of one block (128 KiB) for the bad-block table, enable hardware ECC (typically 4-bit or 8-bit per 528 B sector) in the host controller, and respect the tR/tPROG/tBERS timing budgets. Decoupling must include 0.1 uF plus 4.7 uF near VCC, and WP# should be tied high or driven by the host during in-system programming. This page synthesizes Macronix datasheet specifications, distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet itself, providing a one-stop engineering reference.

RFQ संपर्क
MX30UF4G26AB - 1.8V 4Gbit SLC NAND Flash | Macronix
MX30UF4G26AB

MX30UF4G26AB - 1.8V 4Gbit SLC NAND Flash | Macronix

The Macronix MX30UF4G26AB is a 1.8V 4Gbit SLC NAND Flash memory with parallel interface, organized as 256M x 16, housed in a 63-ball VFBGA package (9x11 mm). It provides 25 ns access time and supports industry-standard ONFI 1.0 timing, making it suitable for high-reliability code and data storage in industrial, networking and embedded designs. SLC NAND Flash is a type of non-volatile memory that stores one bit per cell, delivering higher endurance (typically 60K-100K P/E cycles), faster write throughput, and lower bit error rates than MLC or TLC NAND. It sits within the broader hierarchy of NAND Flash -> non-volatile memory -> semiconductor memory -> integrated circuit, and is widely used where MLC/TLC endurance is insufficient but raw density must remain high. Key features of the MX30UF4G26AB include 4Gbit (4,096 Mbit) density, single-level cell (SLC) architecture, 1.7V to 1.95V single supply operation, and a 16-bit parallel data bus. The device integrates an internal page buffer, ECC status flag and ONFI parameter page support, simplifying host firmware integration. Its 25 ns asynchronous access time delivers 40 MB/s sustained read throughput when paired with a properly designed controller. The architecture combines a charge-trap floating-gate cell with ONFI-compatible command set, ECC-ready status reporting, and multi-plane page programming. Built-in hardware reset and write-protect pins add robustness against unexpected power transients during in-field programming. Typical applications include industrial solid-state drives, factory automation controllers, networking line cards, automotive infotainment storage, and boot/loader code memory in set-top boxes. The 1.8V Vcc also makes it well suited for portable and battery-powered devices where energy efficiency matters. When designing with this part, ensure the host controller supports ONFI 1.0 asynchronous NAND interface timing and that ECC strength (BCH or Hamming) matches the recommended bits-per-512-byte window. This page synthesizes distributor pricing, drop-in alternatives, application examples, and engineering design notes that go beyond the manufacturer datasheet, helping procurement and design engineers make faster sourcing decisions.

RFQ संपर्क
MX30UF4G28AB - 4Gbit SLC Parallel NAND Flash | Macronix
MX30UF4G28AB

MX30UF4G28AB - 4Gbit SLC Parallel NAND Flash | Macronix

The Macronix MX30UF4G28AB is a 4 Gbit (512 M x 8) Single-Level Cell (SLC) parallel NAND flash memory with a 1.8 V power supply, 25 ns access time, and packaged in a 48-pin TSOP-I (TI suffix) or 63-ball VFBGA (XKI suffix). The device delivers 4 Gbit of non-volatile storage using a parallel asynchronous interface with selectable x8/x16 bus width per datasheet specification. An SLC NAND flash memory stores one bit per cell using a single-level charge representation, offering higher endurance (typically 100k P/E cycles per block), faster write performance, and longer data retention than MLC/TLC counterparts. Within the broader non-volatile memory hierarchy, NAND flash sits between NOR flash (byte-addressable, used for code storage) and managed NAND (e.g., eMMC, UFS - integrating controller and NAND in a single package). SLC NAND specifically targets industrial, automotive, and embedded systems where reliability and write endurance outweigh the per-bit cost advantage of higher-density MLC/TLC. Key features include ONFI 1.0-compatible command set, two-plane operation with Status Enhanced Read command (78h), 25 ns page read access, internal data move/erase, and hardware data protection. The 1.8 V core and I/O voltage (1.7 V to 1.95 V range) makes it suitable for low-power embedded designs, and the TSOP-I package provides a drop-in migration path from legacy parallel NOR/PSRAM layouts. The device uses a charge-trap or floating-gate SLC NAND array organized as 4096 blocks (typical 128 Kbytes each) with 2112-byte pages (2048 data + 64 spare), supporting single-plane and two-plane page read/program operations. The asynchronous parallel interface is fully multiplexed with CE, ALE, CLE, RE, WE control signals to a shared 8/16-bit I/O bus, and the integrated controller manages ECC, bad-block management, and wear-leveling hints. Typical applications include industrial embedded storage (HMI, PLC data logging), networking equipment boot+OS storage, automotive infotainment and instrument clusters, set-top box firmware storage, and point-of-sale terminals requiring high-endurance non-volatile memory with parallel interface simplicity. When designing with this part, follow ONFI 1.0 timing parameters, allocate ECC strength of at least 4-bit per 528 bytes (BCH or Hamming), implement bad-block management in firmware, and reserve the spare area for ECC metadata plus block status. Avoid hot-temperature write operations beyond 70 °C if maximum P/E endurance is required. This page synthesizes distributor pricing, drop-in alternatives from the same Macronix NAND family, and practical SLC NAND design notes not aggregated in the manufacturer datasheet alone.

RFQ संपर्क
MX30UF4GE8AB - 4Gb 1.8V SLC NAND Flash, VFBGA-63 | Macronix
MX30UF4GE8AB

MX30UF4GE8AB - 4Gb 1.8V SLC NAND Flash, VFBGA-63 | Macronix

The Macronix MX30UF4GE8AB is a 4 Gbit (512M x 8) 1.8 V Single-Level Cell (SLC) NAND Flash memory device supplied in a 63-ball VFBGA package (9 x 11 mm, 0.80 mm pitch, 1.0 mm height). It is ONFI 1.0 compliant and is designed for low-density, high-reliability code and data storage in embedded systems where long-term data retention, high endurance and predictable latency are required. An SLC NAND Flash is a non-volatile memory that stores one bit per cell, providing higher endurance (typically 100k P/E cycles), faster write speeds and longer data retention than MLC/TLC NAND. SLC NAND belongs to the NAND flash memory category, which is part of the broader non-volatile memory class within semiconductor memory ICs. SLC is widely used in industrial, automotive, networking and IoT applications where MLC/TLC reliability is insufficient. Key features include a 1.8 V single supply operation, 512M x 8 organization, x8 I/O bus, ONFI 1.0 parameter page support with CRC verification, internal data move (copy-back) operation, and multi-plane program/erase architecture for higher throughput. The device supports standard NAND command sets and is drop-in compatible with the broader ONFI 1.0 ecosystem used by other 1.8 V SLC NAND families. The MX30UF family is implemented in a robust 1.8 V process, with an operating voltage range of 1.7 V to 1.95 V and an extended temperature grade typically rated -40C to +85C for industrial use. The internal ECC-friendly interface and dedicated hardware read/write commands simplify firmware integration. Typical applications include industrial embedded Linux boot storage, automotive infotainment and telematics code/data storage, networking equipment firmware, IoT gateways with local data logging, and consumer STB/PND systems. The SLC endurance profile makes the device especially suitable for write-intensive logging in surveillance, point-of-sale and metering. When designing with this device, follow standard NAND layout practices: keep the 8-bit data bus length-matched, place 0.1 uF + 10 uF decoupling close to VCC and VCCQ, and route the R/B# pin with a pull-up. A controller must implement ECC and bad block management, as per ONFI 1.0. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.

RFQ संपर्क
MX574AJMWI/PR+W - 12-Bit 40kSPS SAR ADC, 28-SOIC | Maxim Integrated
MX574AJMWI/PR+W

MX574AJMWI/PR+W - 12-Bit 40kSPS SAR ADC, 28-SOIC | Maxim Integrated

The Analog Devices (formerly Maxim Integrated) MX574AJMWI/PR+W is an industry-standard 12-bit successive-approximation analog-to-digital converter (SAR ADC) with a single-ended 1-input configuration, housed in a 28-pin SOIC (0.295 inch / 7.5 mm width) surface-mount package and specified for commercial temperature grade operation. It delivers up to 40 ksps sampling rate on a parallel data interface and integrates an on-chip clock and voltage reference, eliminating the need for external timing components and saving board area. The converter combines high-speed conversion with low power consumption, a hallmark of the legacy MAX174 / MX574A / MX674A ADC family. A successive-approximation register ADC is a type of data converter that resolves a sampled analog input one bit at a time using an internal binary-search algorithm and a precision DAC. SAR ADCs occupy the middle ground between slow but accurate delta-sigma converters and fast but noisy flash converters, and are commonly used when both deterministic latency (one conversion per N clock cycles) and moderate-to-high accuracy (10 to 16 bits) are required at sampling rates from a few kSPS up to several MSPS. As an ADC, this part belongs to the broader hierarchy: data converter -> ADC -> SAR ADC -> integrated circuit -> semiconductor. Key features include 12-bit resolution, a single-ended input, a parallel output bus, and built-in reference. The on-chip reference removes an external precision component, while the built-in clock simplifies timing by allowing an external crystal or RC to drive the converter. The wide 28-SOIC gull-wing footprint supports standard surface-mount assembly and hand-reworkable prototypes, and the commercial temperature grade makes the part well suited to lab and indoor equipment rather than harsh-environment installations. Typical applications include broadband fixed-line access equipment, test and measurement instrumentation, and enterprise machine control systems. The combination of moderate sampling speed, integrated reference, and parallel readout makes the MX574A family a long-time workhorse in process-control front ends and rack-mounted data-acquisition boards. The PR+W suffix denotes a specific reel and pin-1 orientation variant of the same silicon die as the MX574AJMWI/PR+, and is fully pin-compatible with the rest of the MX574A 28-SOIC family. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that are not consolidated in the manufacturer datasheet itself, giving procurement and design engineers a single reference for evaluating, sourcing, and replacing this legacy Maxim ADC.

RFQ संपर्क
MX574ALCWI+ - 12-Bit Precision SAR ADC, 28-SOIC | Maxim Integrated
MX574ALCWI+

MX574ALCWI+ - 12-Bit Precision SAR ADC, 28-SOIC | Maxim Integrated

The Analog Devices (formerly Maxim Integrated) MX574ALCWI+ is a 12-bit, successive-approximation-register (SAR) analog-to-digital converter with 1 single-ended input, supplied in a 28-pin SOIC package. Per the Maxim datasheet, it is part of the industry-standard MAX174/MX574A/MX674A family of complete 12-bit ADCs that integrate a high-speed SAR core, on-chip clock, internal buried-zener voltage reference, and a precision DAC, delivering a complete ADC function in a single IC. Typical conversion time is approximately 25 us using the internal clock and the internal 10V reference, which simplifies board design versus discrete ADC implementations. What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a type of data converter that performs a binary search across an internal DAC to determine the digital code of the input analog voltage. SAR ADCs sit in the broader hierarchy of data converters (ADC -> data converter -> data acquisition -> signal chain IC -> semiconductor) and are valued for high accuracy, low latency, deterministic latency, and lack of pipeline delay - making them ideal for multiplexed data-acquisition front ends and industrial instrumentation. The MX574A/MX674A series is a long-standing industry workhorse used in legacy designs that still require drop-in replacements today. Key features include 12-bit resolution with no missing codes, +/-1 LSB maximum integral nonlinearity (INL) on the A-grade part, an internal 10V buried-zener reference with low drift, and flexible input ranges of 0V to 10V, 0V to 20V, +/-5V, and +/-10V selected by pin strapping. The device supports both unipolar and bipolar true-bipolar analog input operation without external signal conditioning. Throughput is up to 40 ksps using the internal clock and an external start-conversion pulse, and the device operates from +/-12V to +/-15V (or +5V digital supply). The SOIC-28 package exposes the analog inputs, reference, and digital bus separately for clean PCB layout. Technically, the MX574ALCWI+ uses a charge-redistribution SAR architecture with a thin-film resistor-ladder DAC and laser-trimmed reference. The on-chip clock oscillator eliminates the need for an external crystal or RC timing network for most applications. Three-state outputs allow direct connection to an 8-bit, 12-bit, or 16-bit microprocessor data bus, supporting both 8-bit and 16-bit read modes. A separate -12V/-15V analog supply and +5V digital supply isolate noisy digital currents from the analog input path. Typical applications include industrial process control and data acquisition, multiplexed analog input modules, precision instrumentation, vibration and strain-gauge signal conditioning digitizers, and medical monitoring front ends. Its single-supply bipolar input ranges also suit legacy PLC analog I/O cards and SCADA systems that still use +/-10V signal standards. Replacement situations are common, as the part is widely second-sourced by ADI/PMI and has been continuously manufactured for over three decades. When designing with this part, ensure the analog and digital grounds are separated at the IC and joined only at one point to prevent digital ground-return currents from coupling into the analog input. A 10 uF bypass cap on the +5V digital supply and a 10 uF + 0.1 uF combination on the +/-15V analog supplies minimize noise. The reference output (REF OUT, pin 11) should be buffered if multiple loads are driven, since the internal reference cannot supply heavy current. This page synthesizes distributor pricing, same-brand SAR ADC alternatives in SOIC-28, drop-in recommendations, and practical design notes not found on a single distributor listing, complementing the manufacturer datasheet.

RFQ संपर्क
MX574ALCWI+T - 12-Bit 40kHz SAR ADC, 28-SOIC | Maxim Integrated
MX574ALCWI+T

MX574ALCWI+T - 12-Bit 40kHz SAR ADC, 28-SOIC | Maxim Integrated

The Analog Devices (formerly Maxim Integrated) MX574ALCWI+T is an industry-standard, complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) with an on-chip precision voltage reference and on-chip clock, housed in a 28-pin wide-body SOIC package. The +T suffix indicates tape-and-reel packaging for high-volume assembly. The part combines a 12-bit resolution with a maximum throughput of 40 ksps (typical conversion time ~25 us) and integrates the reference, clock, and SAR logic into a single die, eliminating the external support components that legacy discrete ADC designs required. What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a type of ADC that performs a binary search through successive bits to convert an analog input to a digital code. SAR ADCs sit in the broader hierarchy of ADC architectures (SAR <-> Flash <-> Sigma-Delta <-> Pipeline) and trade off speed and latency for high DC accuracy and very low power consumption, making them well suited for multiplexed data-acquisition systems and industrial process control loops. The MX574A family was originally introduced as an industry-standard pin-compatible upgrade to the classic AD574A. Key features include ±5 V or ±12 V/±15 V analog input ranges (unipolar 0-10 V/0-20 V or bipolar ±5 V/±10 V), ±1 LSB maximum integral nonlinearity (INL), and a built-in +10.000 V buried-Zener reference with ±10 mV initial accuracy. The -L speed-grade variant (MX574ALCWI+T) operates up to 40 ksps; higher speed grades (MX574AJCWI/T, MX574AKCWI/T) are pin-compatible and offer 100 ksps. The on-chip clock eliminates external timing components, and a TRIM pin allows fine adjustment of the internal reference offset and gain. The MX574A's architecture uses a capacitive charge-redistribution DAC and a precision comparator, controlled by the on-chip SAR. Because the reference, comparator, and ladder network are all laser-trimmed at the wafer level, no external calibration is required at room temperature. The chip also offers a unipolar/bipolar input mode pin (BIPOLAR) and an input range pin (10VIN), letting the designer configure full-scale input voltage by pin strapping without external resistor networks. Typical applications include industrial process control front ends, medical instrumentation signal conditioning, data-acquisition (DAQ) cards, and precision transducer readout. The MX574ALCWI+T is also widely used as a replacement for the legacy AD574A in legacy designs where pin compatibility is mandatory. The wide SOIC-28 footprint and ±12 V analog supply tolerance make it tolerant of legacy ±15 V industrial rails. When designing with this device, the analog (VCC) and digital (VLOGIC) supply domains must be decoupled separately with 0.1 uF ceramic capacitors placed within 5 mm of the supply pins. The analog input pin must be driven from a low-impedance source (≤ 1 kohm) to settle within one aperture window; a series 100 ohm resistor followed by a 1 nF capacitor helps buffer transients from a mux. Avoid routing digital outputs near the analog input traces to minimize digital-to-analog crosstalk. The internal reference is trimmed for ±10 mV but drifts with temperature, so for sub-LSB applications external precision references are recommended. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MX574ALEWI+CDR - 12-Bit SAR ADC, 25us, 28-SOIC | Maxim
MX574ALEWI+CDR

MX574ALEWI+CDR - 12-Bit SAR ADC, 25us, 28-SOIC | Maxim

The Analog Devices / Maxim Integrated MX574ALEWI+CDR is an industry-standard, complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) with 25us conversion time, on-chip clock and on-chip voltage reference, packaged in a 28-pin wide-body SOIC (EWI suffix, 300-mil SOP) for commercial temperature grade and shipped on Tape & Reel (CDR suffix). An SAR ADC is a type of data converter that uses a binary search algorithm and an internal capacitive DAC to digitize an analog input. Each conversion takes a fixed number of clock cycles, and the architecture delivers excellent linearity and no pipeline delay, which makes it well-suited to multiplexed data-acquisition front-ends, industrial instrumentation, and process control loops where predictable latency matters more than raw sample rate. Key features include 12-bit resolution, +/-1 LSB maximum linearity error, an internal buried-Zener reference trimmed for low drift, and a tri-state output buffer for direct connection to 8-bit or 16-bit microprocessor buses. The device accepts 0 to +10 V or 0 to +20 V unipolar analog input ranges (and +/-5 V or +/-10 V bipolar ranges when configured), and the parallel byte/word output interface simplifies integration with 8051, 68HC11, and DSP processors. The MX574A uses a precision laser-trimmed thin-film resistor ladder and an on-chip temperature-compensated bandgap reference; successive-approximation registers perform a binary search to produce the digital output. Internal timing is generated by an on-chip oscillator, removing the need for an external conversion clock, while the reference buffer can drive external loads up to 1.5 mA. Typical applications include process control front-ends, multi-channel data-acquisition boards, instrumentation and test equipment, digital panel meters, and any 8051/68HC11/DSP-based system that needs a complete, no-external-component ADC. The 25us conversion time places the part in the medium-speed SAR category - faster than integrating ADCs but slower than 1 MHz successive-approximation converters such as the AD574A. Design tip: keep the analog input bandwidth well below the device's aperture limit and place a small RC filter (typically 100 ohm + 1 nF) ahead of the analog input pin to suppress charge-injection transients from the internal DAC switching. Decouple VCC and VEE with 10 uF tantalum + 0.1 uF ceramic caps placed within 5 mm of the supply pins. This page synthesizes real distributor pricing, drop-in alternatives drawn from the same Maxim MX574A family, and practical design notes not found in the bare manufacturer datasheet.

RFQ संपर्क
MX574ALEWI+TCDR - 12-Bit 25µs SAR ADC, 28-SOIC | Maxim Integrated
MX574ALEWI+TCDR

MX574ALEWI+TCDR - 12-Bit 25µs SAR ADC, 28-SOIC | Maxim Integrated

The Analog Devices (formerly Maxim Integrated) MX574ALEWI+TCDR is an industry-standard, complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) housed in a 28-pin wide-body SOIC (SOIC-28W) package. The MX574A family integrates a high-speed, low-power 12-bit ADC with an on-chip clock, an internal +10V precision buried-Zener voltage reference, and a digital interface that supports ±5V, 0–5V, 0–10V, and ±10V analog input ranges. Maximum conversion time is 25µs at 12 bits, and the part is designed for unipolar or bipolar operation through a single supply configuration. What is a SAR ADC? A successive-approximation-register ADC is a type of data converter that converts an analog input voltage into a digital code using a binary-search algorithm implemented with a comparator, a DAC, and a successive-approximation register. SAR ADCs occupy the sweet spot between slow integrating converters (which offer excellent linearity at low speed) and fast flash ADCs (which offer high speed but consume significant power and pin count). They deliver 8 to 18 bits of resolution at sample rates from a few hundred kSPS to a few MSPS, with deterministic latency, no pipeline delay, and very low power consumption - making them ideal for multiplexed data-acquisition systems, industrial process control, and instrumentation. Key features of the MX574ALEWI+TCDR include ±1 LSB max integral linearity error (A-grade), 25µs maximum conversion time, a built-in +10V reference with ±0.25% initial accuracy, 12-bit parallel and serial interface options, and three-state output buffers that allow direct connection to microprocessor data buses. The device operates from ±12V or ±15V analog supplies with a +5V digital supply, and its bipolar-input capability simplifies signal-conditioning front ends for industrial sensors and audio equipment. The MX574A architecture combines a precision thin-film resistor network, a CMOS comparator, a current-mode DAC, and a SAR register, all trimmed at the wafer level. This integration eliminates external trimming and allows designers to use the ADC immediately after power-up without calibration routines, which historically made the MX574A the de-facto industry-standard 12-bit ADC for both standalone and embedded data-acquisition boards. Typical applications include industrial process control, multiplexed data-acquisition front ends, signal isolation front ends paired with opto-isolators, precision measurement instrumentation, audio digitizers, and embedded board-level designs where +12V supplies are available and -48V telecom battery monitoring is required. When designing with this part, provide a clean +5V digital supply decoupled with 0.1µF and 10µF capacitors close to the supply pins. Use a separate analog ground plane for the input and reference sections, and route the 12-bit parallel bus away from the analog inputs to prevent digital coupling into the converter. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MX574ALN+ - 12-Bit Industry-Standard ADC | Maxim Integrated
MX574ALN+

MX574ALN+ - 12-Bit Industry-Standard ADC | Maxim Integrated

The Maxim Integrated MX574ALN+ is an industry-standard, complete 12-bit successive-approximation analog-to-digital converter (ADC) that combines high conversion speed, low power consumption, an on-chip clock, and an internal voltage reference in a single 28-pin PDIP (DIP-28) through-hole package. It accepts a unipolar analog input range of 0V to 10V or 0V to 20V (and bipolar ±5V or ±10V with proper drive), achieves 12-bit resolution with no missing codes over the commercial temperature range, and uses a high-speed successive-approximation architecture. Key headline specifications include a 40 µs (typ) maximum conversion time, ±5V or ±10V input ranges with input protection, an internal buried-Zener reference trimmed to ±0.3% (10V mode), and 1/2 LSB max integral nonlinearity. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples a continuous analog voltage and quantizes it into a discrete digital code, forming the bridge between real-world analog signals and digital processors. Successive-approximation ADCs (SAR ADCs) use a binary-search algorithm with an internal DAC and comparator to converge on the input voltage one bit per clock cycle; they sit in the broader taxonomy of ADC architectures alongside flash, sigma-delta, pipeline, and integrating ADCs, and are prized for a favorable balance of speed, resolution, and low power consumption. The MX574A belongs to the industry-standard ADC family that has been second-sourced for decades, making it a common legacy building block in industrial, instrumentation, and process-control designs. Key features of the MX574ALN+ include a built-in track-and-hold amplifier, three-state output buffers that interface directly to an 8-/12- or 16-bit microprocessor data bus, and an internal 10V buried-Zener reference that is laser-trimmed to within ±0.3% maximum error. The converter is specified for the commercial temperature range of 0°C to +70°C, operates from standard ±15V and +5V supplies, and provides digital control inputs for conversion start and byte-multiplexed read cycles. Its parallel 12-bit output simplifies integration with legacy 8-bit microprocessors such as the 8080, 6800, and Z80 family, where two successive read cycles deliver the 8 LSBs and 4 MSBs. Typical applications include process-control instrumentation, data-acquisition front ends, precision sensor signal conditioning, panel meters and digital voltmeters, medical instrumentation front ends, and legacy industrial automation systems. The wide ±15V-tolerant analog input stage and robust 12-bit linearity make it a strong fit for digitizing transducer outputs (load cells, pressure transducers, thermocouple amplifiers) where 1 LSB resolution at 10V full scale (2.44 mV) is acceptable and design reuse matters. When designing with this device, observe the analog input current requirements during acquisition; an external buffer amplifier or proper RC network may be required for high-impedance sources. The internal reference pin (REF) should be decoupled with a 10 µF tantalum and 0.1 µF ceramic pair per the manufacturer application note to minimize reference-induced conversion noise. Note that the MX574A is a long-running legacy part - confirm long-term availability before committing to new high-volume designs.

RFQ संपर्क
MX574ALP+T - 12-Bit SAR ADC, 28-PLCC | Maxim Integrated
MX574ALP+T

MX574ALP+T - 12-Bit SAR ADC, 28-PLCC | Maxim Integrated

The Maxim Integrated MX574ALP+T (now under Analog Devices) is an industry-standard 12-bit successive-approximation analog-to-digital converter (SAR ADC) that combines high conversion speed, low power consumption, and a complete on-chip interface including clock and buried-zener voltage reference, housed in a 28-pin PLCC (11.51 x 11.51 mm) package with J-bend terminals. What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a sampling data converter that uses a binary-search algorithm to converge on the input voltage. SAR ADCs sit in the broader hierarchy of ADC architectures (SAR -> data converter -> ADC -> signal chain IC -> semiconductor) and are favored for precision instrumentation because they deliver medium-to-high resolution (12-18 bits) at medium speeds (100 kSPS to few MSPS) without the latency of delta-sigma converters or the glitch of flash converters. The MX574A belongs to the industry-standard "574/674/174" ADC family, originally industry workhorses for industrial process control. Key features include 12-bit resolution with no missing codes over the full temperature range, a precision 10 ppm/°C (max) low-drift internal reference, a track/hold amplifier front end, and a parallel/word-wide digital interface for fast microprocessor read cycles. The device accepts 0 to +10 V or 0 to +20 V unipolar or ±5 V, ±10 V bipolar analog input ranges depending on strap configuration, and runs from ±12 V / +5 V analog supplies. Conversion time is on the order of 25 µs maximum, supporting data-acquisition rates up to ~40 kSPS at full 12-bit accuracy. Typical applications include high-accuracy process-control front ends, digital-signal-processing front ends, high-speed data-acquisition boards, and electro-mechanical test systems. The wide input voltage ranges make the MX574ALP+T drop-in usable in legacy industrial backplanes built around +10 V signal conditioning. When designing with this ADC, ensure the AV+/AV- analog supplies are well decoupled and that the impedance driving the analog input is well below the source-impedance budget to avoid gain errors. The internal reference can be overridden by an external reference if drift budgeting demands it. This page synthesizes live distributor pricing, parametric drop-in alternatives, and practical design notes that complement the manufacturer datasheet for engineers evaluating the MX574ALP+T.

RFQ संपर्क
MX674AKN+ - 12-Bit 15us SAR ADC, 28-DIP | Maxim Integrated
MX674AKN+

MX674AKN+ - 12-Bit 15us SAR ADC, 28-DIP | Maxim Integrated

The Maxim Integrated MX674AKN+ is a 12-bit, industry-standard, complete analog-to-digital converter (ADC) that combines high speed, low power consumption, and on-chip clock and voltage reference in a 28-pin PDIP (0.600 inch, 15.24 mm) through-hole package. It uses a successive-approximation-register (SAR) architecture with a single-ended analog input and provides parallel digital output, with a maximum conversion time of approximately 15 microseconds per sample. The device operates from +/-11.4 V to +/-16.5 V analog supplies with a +5 V digital supply and supports both external and internal voltage reference modes. A SAR ADC is a class of data converter that performs a binary search through an internal sample-and-hold and comparator network to digitize an analog input in N clock cycles for an N-bit output. SAR ADCs sit in the broader hierarchy of analog-to-digital converters -> data converters -> data acquisition ICs -> signal chain ICs -> power management and signal chain semiconductors. SAR converters are valued for deterministic latency, no pipeline delay, and excellent DC accuracy, making them a standard choice for industrial process control, instrumentation, and test equipment where one-shot or low-rate multi-channel sampling is required. The MX674A family's BiCMOS construction reduces power dissipation relative to earlier bipolar-only designs such as the AD574A, while preserving full compatibility with the industry-standard AD574A pinout and timing. Internal reference trim eliminates the need for an external reference in many systems, and an external reference input allows designers to ratio-metric applications or to drive absolute-accuracy applications from a precision external source. The 28-PDIP package simplifies prototyping and breadboarding on through-hole boards, while the part's +/-15 V analog range interfaces directly with typical industrial +/-10 V or 0-10 V signal conditioning outputs. Typical applications include industrial process control, automated test equipment, data loggers, medical instrumentation front ends, and precision sensor signal chains. The wide analog supply range (+/-11.4 V to +/-16.5 V) supports +/-12 V and +/-15 V system rails common in factory automation and laboratory instruments. The parallel digital output drives standard microprocessors and microcontrollers without requiring glue logic. When designing with this part, place the analog and digital grounds on a single low-impedance plane and connect them at one point near the ADC to avoid digital switching noise coupling into the analog input. The internal reference settles within the conversion window when the S/H capacitor is properly bypassed; for highest DC accuracy applications, use an external precision reference such as the MAX6350. The device's commercial 0C to +70C operating range limits it to non-automotive, indoor applications. This page synthesizes distributor pricing, drop-in alternatives within the same 28-PDIP footprint, and practical design notes not found in the manufacturer datasheet. Engineers evaluating the MX674AKN+ for a redesign or new design should treat the alternative list as a pin-compatible replacement matrix rather than a functional-equivalence matrix; cross-package alternatives require PCB rework.

RFQ संपर्क