उत्पाद (44,000+)

NC7S00M5X - TinyLogic HS 2-Input NAND Gate, SOT-23-5 | onsemi
NC7S00M5X

NC7S00M5X - TinyLogic HS 2-Input NAND Gate, SOT-23-5 | onsemi

The onsemi NC7S00M5X is a single 2-input high-performance CMOS NAND gate fabricated using advanced silicon-gate CMOS technology, housed in a 5-pin SOT-23-5 surface-mount package. It is part of the TinyLogic HS (High-Speed) family and operates over a wide VCC range of 2.0 V to 6.0 V with a typical propagation delay of approximately 3 ns at 5 V supply, delivering low-power CMOS performance with TTL-compatible switching thresholds. A NAND gate is a fundamental digital logic primitive that performs the logical NAND (NOT-AND) operation on its two inputs. The output is logic LOW only when both inputs are HIGH; otherwise, the output is logic HIGH. As a member of the logic gate family, NAND gates sit inside the Boolean logic hierarchy (AND/OR/NOT/NAND/NOR/XOR), and the NAND gate is functionally complete, meaning any other Boolean function can be implemented using only NAND gates. Within an integrated circuit's hierarchy, the NC7S00 belongs to the logic ICs category, specifically the sub-category of gates and inverters, which feed into larger functions such as flip-flops, arithmetic logic units, and microcontrollers. Key features of the NC7S00M5X include ultra-low quiescent current (ICC < 1 µA at VCC = 5.5 V), high noise immunity thanks to three internal gain stages between input and output, balanced output drive, and ESD protection diodes on all inputs/outputs referenced to the VCC and GND rails. The SOT-23-5 footprint makes it suitable for space-constrained designs such as hand-held, battery-powered, and portable consumer electronics. Architecturally, the NC7S00 uses an advanced silicon-gate CMOS process that combines low static power consumption with high switching speed. The output stage is balanced, capable of sourcing and sinking comparable currents, which improves AC performance in symmetrical loads and prevents ground-bounce issues in dense multi-gate boards. Inputs tolerate voltages up to VCC plus 0.5 V without damage. Typical applications include handheld and portable electronics, general-purpose logic level translation and interface buffering, signal conditioning in sensor front-ends, low-power standby controllers, mobile phones, PDAs, and industrial control logic where minimal board area is critical. Designers often use the NC7S00M5X as a building block for oscillator circuits, reset sequencers, and conditional-enable logic. When designing with this device, observe proper high-frequency PCB practices: place a 0.1 µF decoupling capacitor within 2 mm of the VCC pin, and route input traces away from the output to avoid feedback-induced oscillations. The input ESD network makes the pin robust to handling, but layout cleanliness still determines overall system noise immunity. This page consolidates distributor pricing for the NC7S00M5X, identifies pin-compatible drop-in alternatives in the same SOT-23-5 footprint, and provides design notes that complement the manufacturer datasheet without repeating it verbatim.

RFQ संपर्क
NC7S02M5X - TinyLogic 2-Input NOR Gate SOT-23-5 | onsemi
NC7S02M5X

NC7S02M5X - TinyLogic 2-Input NOR Gate SOT-23-5 | onsemi

The onsemi NC7S02M5X is a single 2-input high-performance CMOS NOR gate from the TinyLogic HS (High Speed) family, supplied in a 5-pin SOT-23-5 surface-mount package on tape and reel. Fabricated in advanced silicon-gate CMOS, it delivers high-speed, low-power logic operation over a broad VCC range. A logic gate is the most fundamental building block of digital electronics: it takes binary inputs and produces a binary output according to Boolean rules. A NOR gate outputs a LOW only when any input is HIGH, and is functionally complete, meaning any digital circuit can be built from NOR gates alone. Single-gate logic devices like the NC7S02 occupy the lowest level of the logic IC hierarchy, below multi-gate families such as 74HC quad gates, and belong to the broader class of small-scale integration (SSI) CMOS logic. Key features of the NC7S02 include TinyLogic HS single-gate packaging that saves board space versus quad-gate SOIC-14 alternatives, silicon-gate CMOS technology for speed with minimal static power consumption, and ESD protection diodes on both inputs and output with respect to VCC and GND rails. Three stages of gain between inputs and outputs assure high noise immunity and reduced propagation-delay sensitivity. Technically, the three-stage output buffering provides symmetrical drive and sharp transitions, while the broad VCC range allows direct interfacing with 5V, 3.3V, and lower-voltage logic domains within the specified operating limits. The inherent rail-clamping ESD structure simplifies board-level protection in mixed-signal environments. Typical applications include glue logic in microcontroller and FPGA systems, power-down domain isolation in battery-powered portable equipment, signal inversion or OR-ing in space-constrained designs, and retry or reset control in embedded industrial boards such as MC9S08 or MC9S12 based systems. When designing with this part, keep unused input tied to a valid logic level (VCC or GND) to prevent oscillation, and place 0.1uF decoupling close to the VCC pin. Confirm propagation delay and drive current against the onsemi datasheet for your VCC and temperature corner. This page synthesizes distributor pricing tiers, drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
NC7S02M5X-L22090 - TinyLogic HS 2-Input NOR Gate | onsemi
NC7S02M5X-L22090

NC7S02M5X-L22090 - TinyLogic HS 2-Input NOR Gate | onsemi

The onsemi NC7S02M5X-L22090 is a single-channel 2-input NOR gate fabricated in advanced CMOS silicon-gate technology and housed in a 5-pin SOT-23-5 (TSOP-5/M5) surface-mount package. It belongs to the TinyLogic HS (High-Speed) family, offering high-speed logic operation over a broad VCC supply range in one of the smallest standard discrete-logic footprints available. A NOR gate is a fundamental combinational logic element that outputs a LOW only when all inputs are HIGH; it is functionally complete, meaning any digital circuit can be built from NOR gates alone. In the digital IC hierarchy, the NC7S02 sits within the single-gate logic IC category (also called little logic or TinyLogic), between full 74-series multi-gate packages and application-specific ICs, and is used wherever board space, propagation delay, or parasitic loading make a full quad-gate package impractical. Key features include single 2-input NOR functionality in SOT-23-5, CMOS construction for very low static power consumption, ESD protection diodes on both inputs and the output relative to VCC and GND, and three stages of internal gain that assure high noise immunity while reducing output-stage switching sensitivity, per the onsemi NC7S02 datasheet. Technically, the silicon-gate CMOS process delivers speed comparable to bipolar-era logic at CMOS power levels, and the buffered three-stage topology isolates the inputs from the output transition, minimizing ground bounce in mixed-signal boards. The broad VCC operating range allows direct interfacing with 3.3V and 5V logic domains within rated conditions. Typical applications include glue logic in microcontroller and FPGA systems, oscillator and RC-timer circuits, pulse stretching and delay generation, enable/signal gating in portable and battery-powered consumer devices, and board-level chip-select combining where a full 74x02 package would waste space. Design consideration: as with all single-gate CMOS parts, unused input states must never float - tie unused inputs to VCC or GND through an appropriate connection to prevent oscillation and excess current. Keep decoupling (100 nF) close to pin 5. This page synthesizes verified distributor pricing from DigiKey, Mouser, Octopart and Vyrian, same-package drop-in alternatives, and practical design notes that are not consolidated in the manufacturer datasheet.

RFQ संपर्क
NC7SV125P5X - TinyLogic ULP-A Non-Inverting 3-State Buffer, SC-70-5 | onsemi
NC7SV125P5X

NC7SV125P5X - TinyLogic ULP-A Non-Inverting 3-State Buffer, SC-70-5 | onsemi

The onsemi NC7SV125P5X is a single non-inverting 3-state buffer from the TinyLogic Ultra Low Power-A (ULP-A) family, housed in a 5-pin SC-70 surface-mount package. It is designed for VCC operation from 0.9 V to 3.6 V, and is fabricated in CMOS technology to deliver extreme high speed, high drive, and low static power consumption in tiny footprint packages. A 3-state buffer (also called a tri-state buffer, line driver, or bus driver) is a single-input/single-output non-inverting logic device whose output can be placed in one of three states: logic high, logic low, or high-impedance (Hi-Z). Buffers are the simplest members of the Logic ICs category, sitting hierarchically below gates, transceivers, and bus switches. Their primary function is signal isolation, level shifting, bus arbitration, and output drive-strength amplification on shared digital lines such as microcontroller I/O buses, memory data lines, and peripheral interconnects. Key specifications of the NC7SV125P5X include a wide VCC range of 0.9 V to 3.6 V, ±24 mA output drive at 3.3 V VCC, low quiescent current typically below 1 µA, and a propagation delay in the low-nanosecond range that supports high-speed digital interfaces. The 3-state output is controlled by an active-low output enable (OE\) pin; when OE\ is high the output enters Hi-Z, allowing multiple devices to share a common bus. The SC-70-5 package measures approximately 2.0 mm x 1.25 mm, making it one of the smallest logic footprints available. Architecturally the device uses a minimum-stage CMOS inverter chain, which is why propagation delay is extremely short and dynamic power scales linearly with load capacitance and switching frequency. The NC7SV125P5X is specified over the industrial -40 °C to +85 °C temperature range and is fully RoHS compliant, with Pb-free lead finish and a Moisture Sensitivity Level (MSL) of 1, simplifying handling and board assembly. Typical applications include mobile phones, tablets, wearable electronics, IoT sensor nodes, handheld instruments, and any battery-powered product that needs bus isolation or output drive amplification in a sub-3 mm² footprint. Designers favor this part when board real estate is at a premium and a low-power, rail-to-rail CMOS buffer is required. When designing with the NC7SV125P5X, place input and output decoupling capacitors (typically 0.1 µF) close to the VCC and GND pins to limit supply-rail bounce during high-speed switching. Always keep the OE\ pin at a defined logic level; floating enables can cause shoot-through current and unwanted output toggling. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers quickly decide whether the NC7SV125P5X is the right 3-state buffer for their next low-power, space-constrained design.

RFQ संपर्क
NC7SZ00M5X - UHS 2-Input NAND Gate, SOT-23-5 | onsemi
NC7SZ00M5X

NC7SZ00M5X - UHS 2-Input NAND Gate, SOT-23-5 | onsemi

The onsemi NC7SZ00M5X is a single two-input NAND gate from the TinyLogic Ultra-High Speed (UHS) series, fabricated with advanced CMOS technology to achieve 2.4 ns typical propagation delay while maintaining low static power dissipation across a 1.65 V to 5.5 V VCC operating range, housed in a 5-pin SOT-23 (SC-74A / SOT-753) package. A NAND gate is a fundamental digital logic primitive that performs the logical complement of the AND operation: the output is LOW only when both inputs are HIGH, otherwise the output is HIGH. NAND gates are functionally complete - any Boolean function can be implemented using only NAND gates - which is why they are the most replicated gates in CMOS digital IC families. Within the broader taxonomy, the NC7SZ00 belongs to the TinyLogic UHS family, which sits under standard logic gates, which sits under logic ICs, which sits under integrated circuits. Key features include 2.4 ns typical propagation delay (tPD) into a 50 pF load at 5 V VCC, ±24 mA high output drive at 3 V VCC, broad 1.65 V to 5.5 V operating range, and proprietary noise/EMI reduction circuitry. The device is over-voltage tolerant on inputs, facilitating 5 V to 3 V translation without external level shifters. The NC7SZ00 architecture uses a standard CMOS NAND topology with input hysteresis and balanced output drive, optimized for sub-3 ns switching at low power. Matched LCX-class performance at 3.3 V VCC means it can directly replace legacy LCX NANDs in mixed-voltage designs without PCB rework. Typical applications include portable and battery-powered devices, mobile phone handsets, computing peripherals, level shifting between 5 V and 3.3 V domains, and general-purpose glue logic on microprocessor and ASIC boards. The SOT-23-5 footprint makes it ideal for space-constrained handheld designs. When designing with this device, observe standard CMOS handling precautions: unused inputs must be tied to VCC or GND to prevent floating, and high-impedance I/O behavior occurs during power-down. Decouple VCC with a 0.1 µF ceramic capacitor placed close to the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in the onsemi datasheet, giving engineers a single reference for selection, sourcing, and PCB-level integration.

RFQ संपर्क
NC7SZ04P5X - Single UHS TinyLogic Inverter, 5.5V | onsemi
NC7SZ04P5X

NC7SZ04P5X - Single UHS TinyLogic Inverter, 5.5V | onsemi

The onsemi NC7SZ04P5X is a single-channel CMOS inverter from the TinyLogic Ultra-High Speed (UHS) series, housed in a 5-pin SC-70 package (P5X suffix). It operates over a 1.65 V to 5.5 V VCC range and delivers a typical propagation delay of 2.4 ns into a 50 pF load at 5 V VCC, while the ±24 mA output drive at 3 V VCC provides strong signal integrity. According to the onsemi datasheet for the NC7SZ04 family, the part is fabricated with advanced CMOS technology to achieve ultra-high speed with high output drive and low static power dissipation over the full 1.65 V to 5.5 V supply range. What is a TinyLogic UHS inverter? A TinyLogic UHS (Ultra-High Speed) inverter is a single-stage CMOS logic gate that performs the logical NOT function (Y = ~A) and belongs to the TinyLogic family of discrete logic ICs. In the broader component taxonomy, this device is a logic gate -> inverter -> digital logic IC -> semiconductor IC. These gates are ideal for level translation, signal inversion, clock buffering, and general-purpose logic glue in mixed-voltage systems where board space is critical and a single inverter is needed. Key features of the NC7SZ04P5X include ±24 mA high output drive at 3 V VCC, an over-voltage tolerant input that facilitates 5-V to 3-V translation, power-down high-impedance inputs/output, proprietary noise/EMI reduction circuitry, and propagation delay that matches LCX performance when operated at 3.3 V VCC. The device is also offered in an ultra-small MicroPak leadless package for space-constrained designs. Architecturally, the NC7SZ04P5X uses advanced CMOS with a standard CMOS input structure. The high output drive (±24 mA at 3 V VCC) means it can drive heavily loaded buses and long PCB traces while maintaining fast rise/fall times. The over-voltage tolerant input allows 5 V CMOS signals to be safely applied even when VCC is as low as 1.65 V, eliminating the need for external level shifters in many mixed-voltage designs. Typical applications include level translation between 5 V and 3.3 V logic domains, general-purpose logic inversion in handheld and portable devices, signal conditioning in battery-powered equipment, oscillator and clock-buffer building blocks, and fan-out for microcontroller GPIO in space-constrained designs. The SC-70-5 footprint makes it well suited when only a single inverter is required on a dense mixed-signal board. When designing with this device, route der through a 5-pin to keep the trace between the input pin and the source under 50 mm and place a 0.1 µF decoupling capacitor within 5 mm of the VCC pin to maintain power-rail noise immunity. The over-voltage tolerant input is a key design advantage in mixed-voltage systems where 5 V CMOS signals can be applied even when VCC is as low as 1.65 V, allowing true 5 V-to-3 V translation without external protection. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-brand onsemi family members and pin-compatible cross-brand equivalents for second-source flexibility.

RFQ संपर्क
NC7SZ08L6X - Ultra-High-Speed 2-Input AND Gate | onsemi
NC7SZ08L6X

NC7SZ08L6X - Ultra-High-Speed 2-Input AND Gate | onsemi

The onsemi NC7SZ08L6X is a single two-input AND gate in the TinyLogic Ultra-High Speed family, operating from 1.65 V to 5.5 V in a 6-pin MicroPak package. It combines fast propagation performance with high output drive and low static power dissipation across a broad supply range. The L6X ordering code identifies the onsemi surface-mount package and tape-and-reel shipping configuration. A logic AND gate is a combinational digital component that produces a high output only when every input is high. This gate belongs to the hierarchy of CMOS logic gates, digital logic ICs, semiconductors, and broader digital electronics. A single two-input gate is useful when a design requires basic Boolean AND behavior in compact routing, signal conditioning, control logic, or low-power digital interfaces. The NC7SZ08 is fabricated with advanced CMOS technology. Its specified 1.65 V to 5.5 V supply operation supports both low-voltage digital systems and conventional 3.3 V or 5 V rails. The TinyLogic UHS positioning emphasizes ultra-high-speed operation while retaining low static power dissipation. These characteristics make the device appropriate where logic transitions must be handled quickly without using a larger multi-gate package. The verified distributor listings identify the NC7SZ08L6X as an AND gate IC with one channel, two inputs, and a 6-MicroPak package. Available source material confirms the TinyLogic UHS 2-input AND function and CMOS technology. Exact propagation-delay, output-current, input-threshold, and temperature values were not supplied in the retrieved source data and therefore are not asserted here. Typical uses include low-voltage control logic, digital signal routing, status-flag generation, and compact embedded systems where a dedicated two-input AND function is preferable to implementing the Boolean operation in a larger programmable or multipurpose logic device. Designers should also consider whether the required logic family, supply voltage, input levels, and timing satisfy the system requirements. For PCB layout, keep the unused input connected to a defined logic level rather than leaving it floating, and place the device close to the signals it serves. Confirm the exposed-pad or thermal-pad requirements in the manufacturer package drawing and verify the pin mapping against the applicable datasheet before releasing a layout. This product page combines verified distributor identity, package information, pricing references, technical context, and replacement guidance. It distinguishes confirmed facts from parameters that still require direct confirmation from the manufacturer datasheet, helping engineers make sourcing and design decisions without relying on unsupported assumptions.

RFQ संपर्क
NC7SZ125M5X - UHS Single Buffer, 3-State, SOT-23-5 | onsemi
NC7SZ125M5X

NC7SZ125M5X - UHS Single Buffer, 3-State, SOT-23-5 | onsemi

The onsemi NC7SZ125M5X is a single non-inverting buffer with 3-STATE capability, fabricated with advanced CMOS technology to deliver ultra-high speed (UHS) switching with high output drive while maintaining low static power dissipation. Housed in a 5-pin SOT-23 (M5) surface-mount package, the device operates across a wide 1.65 V to 5.5 V VCC range, supports ±24 mA output drive at 5 V, and features a typical propagation delay of approximately 2.6 ns at 5 V VCC, making it well suited for high-speed signal conditioning in mixed-voltage systems. The 3-STATE output is controlled by an active-low output enable (OE) pin, allowing bus-oriented applications and easy interface to microcontrollers, ASICs, and FPGAs. A non-inverting buffer (also called a line driver or signal repeater) is a single-input, single-output logic function that reproduces the logic level present at its input at the output, providing current gain and isolation between a weak source and a heavier load. Within the broader logic IC hierarchy, this part belongs to the TinyLogic UHS family from onsemi, a subset of CMOS logic gates that trade absolute speed for low power consumption. The 3-STATE output allows multiple buffers to share a common bus, with the disabled buffer entering a high-impedance state to avoid contention. The SOT-23-5 package is one of the most ubiquitous footprints in modern surface-mount design. Key features of the NC7SZ125M5X include balanced propagation delays, very low quiescent current (typically 1 µA at room temperature), ±24 mA output drive at 5 V (enabling direct drive of LEDs or small relays), and a wide VCC operating range that makes it compatible with 1.8 V, 2.5 V, 3.3 V, and 5 V logic families. The device contains a single Schmitt-trigger input, providing hysteresis for slow or noisy input edges. Tape and reel packaging (suffix X) supports high-volume automated assembly. From a technical perspective, the NC7SZ125M5X uses a standard CMOS push-pull output stage. The output enable pin OE is internally pulled high through a weak pull-up, so the output remains in high-impedance until actively driven low. Input structures tolerate voltages up to 5.5 V regardless of VCC, allowing level translation between 1.8 V and 5 V domains. ESD protection exceeds 2000 V HBM per industry standards, and latch-up immunity is rated above 100 mA per JESD78. Typical applications include signal buffering between low-drive microcontroller GPIOs and heavier loads such as LEDs, level translation between mixed-voltage logic domains (e.g., 1.8 V to 3.3 V), bus isolation and multiplexing in distributed systems, and general-purpose logic inversion-free signal restoration in handheld and battery-powered designs. In industrial PLCs, it isolates backplane logic from field-side noise. In consumer audio and wearables, it buffers buttons or I2C lines between SoCs and accessory connectors. When designing with this part, ensure OE is driven to a defined logic level rather than left floating, especially in noisy environments, to avoid inadvertent bus contention. Place a 0.1 µF decoupling capacitor close to the VCC pin to suppress logic-stage switching transients, and avoid exceeding the absolute maximum VCC of 6 V. This TinyLogic buffer excels where a single-bit driver, three-state capability, and tiny footprint are required simultaneously. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, comparison parameters, and practical design notes that go beyond what is printed in the manufacturer datasheet alone, giving engineers a faster path from selection to validated PCB layout.

RFQ संपर्क
NC7SZ125M5X-L22090 - TinyLogic UHS Buffer 3-State SOT-23-5 | onsemi
NC7SZ125M5X-L22090

NC7SZ125M5X-L22090 - TinyLogic UHS Buffer 3-State SOT-23-5 | onsemi

The onsemi NC7SZ125M5X-L22090 is a TinyLogic Ultra-High Speed (UHS) single non-inverting buffer with a three-state output, fabricated in advanced CMOS to deliver high output drive and ultra-high switching speed while keeping static power dissipation minimal. Packaged in a 5-pin SOT-23 (M5), the device operates over a 1.65 V to 5.5 V VCC range, supports ±24 mA output drive at 4.5 V, and is rated for industrial -40 C to +85 C operation per the onsemi NC7SZ125 datasheet family. The active-low /OE enable pin allows bus-style multiplexing and high-impedance output when de-asserted. A buffer in CMOS logic is a non-inverting driver that copies a digital input to its output while providing isolation and current amplification between source and load. Buffers belong to the broader family of logic ICs under digital signal conditioning, alongside inverters, transceivers, and line drivers; TinyLogic UHS parts sit at the high-speed end of this taxonomy, optimized for short propagation delay and high fan-out within a small SOT-23 outline. Key specifications include a propagation delay (tPD) of approximately 2.6 ns at 5 V, output drive of ±24 mA at 4.5 V VCC, quiescent current well under 10 uA across the supply range, and TTL-compatible inputs when VCC is at 4.5 V to 5.5 V. The /OE pin features an internal pull-up so the output defaults to high-impedance (effectively disabled) if the pin is left floating, simplifying power-up behavior in mixed-voltage buses. The NC7SZ125 architecture uses a single-stage CMOS inverter/buffer chain with a tri-state output totem pole. Because the silicon is specified over 1.65 V to 5.5 V, the same footprint can serve 1.8 V, 2.5 V, 3.3 V, and 5 V logic domains, making it ideal as a voltage-level translation element when driven from a lower-voltage controller I/O into a higher-voltage bus. Typical applications include point-to-point signal buffering in portable and consumer devices, I/O expansion for microcontrollers, address/data bus isolation in memory and display interfaces, and translation between logic domains in mixed-voltage systems. It is also commonly used as a high-impedance power-gating switch for sub-system rails. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to the VCC pin, and treat the SOT-23-5 thermal pad (when present) as a low-impedance ground return. Avoid driving large capacitive loads (>50 pF) without series damping, because the high drive strength can create ground-bounce issues on tightly-routed boards. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the onsemi datasheet alone, giving engineers a faster decision path for cross-brand or second-source selection.

RFQ संपर्क
NC7WZ14EP6X - UHS Dual Inverter Schmitt Trigger SC-70-6
NC7WZ14EP6X

NC7WZ14EP6X - UHS Dual Inverter Schmitt Trigger SC-70-6

The onsemi NC7WZ14EP6X is a dual Schmitt-trigger inverter from the TinyLogic Ultra-High Speed (UHS) Series, packaged in a 6-pin SC-88 (SC-70-6) surface-mount outline. It operates from 1.65 V to 5.5 V VCC, delivers ±24 mA of balanced output drive at 4.5 V, and achieves typical propagation delays of about 2.0 ns at 5 V. The on-suit Schmitt trigger hysteresis on each input cleans up slow or noisy edges, making the part well suited for signal conditioning in mixed-voltage digital designs. A Schmitt-trigger inverter is a single-input logic gate that outputs the logical complement of its input while adding positive feedback to define two distinct switching points (VT+ and VT-). The hysteresis voltage (typically ~1 V at 5 V) rejects noise on slowly rising or ringing edges that would otherwise chatter a standard CMOS inverter. In the broader TinyLogic family tree it sits beside standard inverters (NC7WZ04) and buffers (NC7WZ17) as the noise-immune variant. Key features of the NC7WZ14EP6X include 1.65 V to 5.5 V VCC operation, ±24 mA output drive at 4.5 V, balanced 4 mA sink/source at 3 V, a propagation delay near 2 ns at 5 V, Schmitt trigger inputs on both channels, and a quiescent current below 1 uA. The SC-88 package with a -40 C to +85 C operating range suits portable and industrial designs where board area is critical. Internally, NC7WZ14EP6X uses advanced sub-micron CMOS to combine very high speed with low static power dissipation across the full VCC range. Two independent inverters share only GND and VCC, simplifying layout. The balanced ±24 mA drive at 4.5 V lets outputs drive long PCB traces or several CMOS loads while keeping edges fast. Typical applications include logic-level translation, oscillator and relaxation-circuit building blocks, debouncing mechanical switches, waveform shaping for sensor outputs, and general-purpose inversion in portable consumer, computing and IoT hardware. It is widely used as a companion to microcontrollers where a clean digital signal is needed. When laying out the SC-88 footprint, place a 0.1 uF VCC decoupling capacitor within about 3 mm of pin 6, keep input traces short to preserve hysteresis noise rejection, and avoid running outputs near analog sections. The -EP6X suffix marks a 3000-piece tape-and-reel packing, -P6X denotes SC-88 (tape and reel), and -P6 marks the same SC-88 on tape. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical layout notes that are not bundled together in the manufacturer datasheet.

RFQ संपर्क
NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi
NCS199A1RSQT2G

NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi

The onsemi NCS199A1RSQT2G is a zero-drift, voltage-output current-shunt monitor (current sense amplifier) with a fixed gain of 50 V/V, supplied in a 6-pin SC-88 / SC-70-6 / SOT-363 surface-mount package. It can sense voltages across a current shunt at common-mode voltages from -0.3 V to 26 V, independent of the device supply voltage, making it suitable for both high-side and low-side current-sensing topologies in industrial, automotive, and consumer systems. The device operates from a single supply of 2.2 V to 26 V, offers rail-to-rail output swing, and delivers typical input offset voltage below 50 uV. A current sense amplifier (CSA) is a type of instrumentation amplifier that converts a small differential voltage developed across a shunt resistor into a ground-referenced output voltage proportional to load current. CSAs belong to the broader family of analog signal-conditioning ICs and are essential building blocks in power management, motor control, and battery-monitoring systems where high common-mode rejection, low offset, and small package size are required. Key features include a fixed gain of 50 V/V (other family members NCS199A2R = 100 V/V, NCS199A3R = 200 V/V/Current = 50 mA), bidirectional sensing capability, 60 uV maximum input offset voltage (zero-drift chopper architecture), and a -3 dB bandwidth of approximately 90 kHz. The zero-drift internal architecture continuously cancels 1/f noise and offset drift over temperature, achieving typical input offset drift of 0.5 uV/C. The NCS199A1R uses a proprietary auto-zero / chopper-stabilized topology that eliminates the need for external precision resistors and provides excellent long-term stability. Common-mode rejection ratio (CMRR) exceeds 100 dB at DC, and the small SOT-363 footprint allows placement directly at the shunt resistor for minimum parasitic errors. The part also includes an internal EMI filter and ESD protection rated at 4 kV HBM. Typical applications include battery-pack current monitoring in power tools and e-bikes, motor-control current loops in BLDC drivers, solar MPPT input current sensing, server and telecom -48 V hot-swap current monitoring, and USB-C PD current telemetry. In all cases the wide -0.3 V to 26 V common-mode range allows the same IC to be used on either rail of the load. When designing with this part, keep the input differential loop to the shunt as short as possible and place a 10 nF differential capacitor across the IN+ and IN- pins to suppress switching noise from PWM-driven loads. Ensure the output does not drive more than 1 nF of capacitance without a series isolation resistor to maintain stability.

RFQ संपर्क
NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi
NCV2202SN2T1G

NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi

The onsemi NCV2202SN2T1G is a sub-one-volt, low-power, single-channel CMOS comparator in a 5-pin SOT-23 (TSOP) package, qualified to the AEC-Q100 automotive standard. It operates over a supply voltage range of 0.85V to 6.0V, consumes only 10 uA of quiescent current, and provides an open-drain output capable of rail-to-rail input and rail-to-rail output swing. The NCV2202 prefix indicates AEC-Q100 / PPAP-capable automotive grade screening, while the non-automotive NCS2202 family member shares the same die and pinout. What is a low-voltage CMOS comparator? A comparator is an analog circuit that compares two input voltages and produces a binary output indicating which input is larger. Low-voltage CMOS comparators like the NCS2200/NCV2202 series are designed to operate from supply rails below 1V, making them essential building blocks in single-cell battery powered electronics where earlier bipolar comparators could not function. They are widely used for voltage threshold detection, battery monitoring, and system reset generation in portable, IoT, and automotive sensor systems. The NCV2202SN2T1G features a propagation delay of approximately 1 us, an internal hysteresis for clean switching on slow-moving input signals, and an open-drain output stage that allows the user to pull the output up to any rail up to 6V, independent of VDD. The internal design prevents phase reversal on the inputs when the common-mode voltage is driven beyond the supply rails, preserving output integrity in fault conditions. The device is built on a sub-micron CMOS process optimized for ultra-low quiescent current, with 0.3 uA consumption when the enable pin is held low (output tri-state). Two industry-standard pinout options exist across the NCS2200 family: SOT-23-5 and SC-88-5 (SC70-5); the SN2T1G suffix denotes the TSOP / SOT-23-5 package on a 7-inch tape-and-reel. Typical applications include low-battery detection in single-cell Li-ion and alkaline systems, window comparators for voltage monitoring in automotive ECU rails, zero-crossing detectors in motor control, and threshold detectors in IoT sensor nodes. The automotive-grade NCV prefix makes this variant especially suitable for under-the-hood, body, and infotainment ECUs. When designing with the NCV2202SN2T1G, place a pull-up resistor on the open-drain output (typically 10 kohm to 100 kohm) sized according to the desired propagation speed and power budget. Decouple VDD with a 100 nF ceramic capacitor located within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

RFQ संपर्क
NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi
NCV2250SN2T3G

NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi

The onsemi NCV2250SN2T3G is a single high-speed, low-voltage, rail-to-rail comparator with push-pull output, packaged in a 5-pin TSOP. It delivers a typical propagation delay of 50 ns with a 100 mV input overdrive, making it well suited for fast threshold detection in space-constrained designs. The part operates from a single 1.8 V to 5.5 V range, and the input common-mode range extends 200 mV beyond both supply rails, allowing direct sensing near ground or VCC. The push-pull output stage eliminates the external pull-up resistor required by open-drain alternatives and swings to within millivolts of both rails. A comparator is an analog active device that compares two input voltages and drives its output logic a discrete single (high or low) based on which input is more positive. Within the broader taxonomy, the NCV801A sits under analog comparator -> comparator -> amplifier/comparator IC -> semiconductor. Push-pull CMOS output topology differs from open-drain comparators (such as the classic LM393) by actively driving both high and low states, enabling faster edges and lower power in many applications. This category of comparator is essential in any mixed-signal system requiring fast logic-level translation from analog signals. Key features include 1.8 V to 5.5 V single-supply operation, 200 mV beyond-the-rails input common-mode range, 50 ns typical propagation delay (100 mV overdrive), push-pull CMOS output, low quiescent current, and automotive-grade NCV prefix indicating PPAP-capable qualification per onsemi's automotive quality program. The 5-TSOP package consumes only a few square millimeters of PCB area, ideal for compact sensor and signal-conditioning modules. The NCV2250 is built on a standard CMOS process with on-chip ESD protection diodes on the inputs and outputs. The rail-to-rail input stage uses a complementary differential pair topology that maintains linear behavior across the full common-mode range. Internally, hysteresis can be introduced via external positive feedback resistors to prevent output chattering on slow-moving inputs. The NCV2250SN2T3G is functionally identical to the NCS2250SN2T3G except for automotive-grade qualification and traceability. Typical applications include zero-crossing detectors for line-voltage sensing, battery voltage monitoring in 12 V automotive systems, window comparators with multi-threshold detection, motor control feedback loops, sensor signal conditioning for microcontroller ADC front-ends, and threshold alarms in industrial control. The wide input common-mode range is particularly valuable for current-sense applications where the sense resistor sits at a high common-mode voltage close to the supply rail. When designing with this part, ensure input signals stay within the ESD rating of the device and consider adding small input series resistance to limit fault current during over-voltage transients. Decoupling the supply pin with a 100 nF ceramic capacitor placed within 3 mm of the VCC pin is essential for stable high-frequency switching performance. This page synthesizes distributor inventory, the parametric equivalent on the manufacturer's cross-reference database, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi
NCV2904DR2G

NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi

The onsemi NCV2904DR2G is a single-supply dual operational amplifier in an 8-pin SOIC (Case 751) package, operating from 3.0 V to 26 V with a common-mode input range extending to ground/VEE, targeted at automotive-grade applications. An operational amplifier (op-amp) is a high-gain differential voltage amplifier that sits within the analog signal chain hierarchy: op-amp -> amplifier IC -> analog IC -> semiconductor. Dual op-amps integrate two independent amplifier cores in one package, halving board space and BOM line items versus two singles. Single-supply op-amps like the NCV2904 are specifically designed for input common-mode ranges that reach the negative rail, making them usable directly on ground-referenced sensor signals without negative supplies. Key features of the NCV2904 include low power drain, short-circuit protected outputs, a true differential input stage, internally compensated frequency response, and ESD clamps on the inputs. The NCV prefix designates onsemi automotive qualification and temperature screening, making this device suitable for under-hood and body-electronics environments. Per the onsemi datasheet, the LM358 series is equivalent to one-half of an LM324, positioning the NCV2904 as the automotive member of this industry-standard family. Technically, the NCV2904 uses the circuit designs perfected for the quad LM2904/LM324 family: an internally compensated architecture that provides unity-gain stability without external compensation components. Single-supply or split-supply operation gives designers flexibility across 3.0 V to 26 V rails, and the input bias currents are low, minimizing offset errors with high-impedance sensors. Typical applications include automotive sensor signal conditioning (throttle position, pressure), battery-voltage monitoring dividers, comparators for window detection in ECUs, and general industrial signal amplification on single 5 V to 24 V rails. A key design consideration: the output cannot swing to the positive rail, so gain-setting must keep target output levels below the VOH specification at the expected load current. This page synthesizes distributor availability, drop-in alternatives across the LM258/LM358/LM2904 family, and practical design notes beyond what the manufacturer datasheet states.

RFQ संपर्क
NDL46PFG-8KIT - 4Gb DDR3L SDRAM 256Mx16 | Insignis
NDL46PFG-8KIT

NDL46PFG-8KIT - 4Gb DDR3L SDRAM 256Mx16 | Insignis

The NDL46PFG-8KIT is a 4Gbit DDR3L SDRAM organized as 256M x 16, operating at 800 MHz (DDR3L-1600) with a CAS latency of 20 ns. It is designed to comply with all key DDR3L DRAM features, with control and address inputs synchronized to a pair of externally supplied differential clocks. Inputs are latched at the cross point of differential clocks (CK rising and CK# falling), and all I/Os are synchronized with a differential DQS pair in a source-synchronous fashion. This device is available in a 96-ball FBGA package (7.5x13.5 mm) and supports a maximum operating temperature of 95°C. DDR3L SDRAM is a type of dynamic random-access memory that operates at a lower voltage (1.35V) compared to standard DDR3 (1.5V), reducing power consumption by up to 20% while maintaining high bandwidth. It is part of the DDR3 memory family, which is widely used in computing, networking, and embedded systems. The NDL46PFG-8KIT is compatible with both 1.5V and 1.35V supplies, offering flexibility in system design. Key features include a 4Gbit density, 16-bit data bus, 800 MHz clock speed (1600 Mbps data rate), and a 20 ns CAS latency. The device supports standard DDR3L features such as on-die termination (ODT), programmable CAS latency, and burst lengths of 8 and 4. It also includes auto-refresh and self-refresh modes for low-power standby. The architecture uses an 8n-prefetch design, enabling high-speed data transfer with reduced I/O clock frequency. The differential clock inputs (CK and CK#) and data strobes (DQS and DQS#) ensure robust signal integrity for high-speed operation. The 96-ball FBGA package provides excellent thermal and electrical performance, making it suitable for space-constrained applications. Typical applications include servers, networking equipment, industrial computing, and embedded systems requiring high-density, low-power memory. The 1.35V operation is ideal for power-sensitive designs, such as battery-powered devices and energy-efficient data centers. When designing with this device, ensure proper decoupling capacitors near the power pins and follow the layout guidelines in the datasheet to minimize signal integrity issues. The device supports a wide operating temperature range, making it suitable for industrial environments.

RFQ संपर्क
NE5532AD - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532AD

NE5532AD - Dual 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532AD is a dual, low-noise operational amplifier designed for audio applications, with a 10 MHz typical unity-gain bandwidth, 5 nV/√Hz typical input noise voltage at 1 kHz, and 100 dB typical high dc voltage gain. The device is supplied in an 8-pin SOIC package. It is unity-gain compensated and combines low noise, low distortion, high output-drive capability, and a typical 32 V peak-to-peak output voltage swing under ±18 V supply conditions. An operational amplifier is an active semiconductor device that uses high gain and negative feedback to amplify voltage differences between its inputs. The NE5532 belongs to the low-noise operational amplifier hierarchy, which sits within analog signal-chain ICs, integrated circuits, and semiconductor devices. Its dual-amplifier configuration provides two independent amplifiers in one package, reducing board area in audio preamplifiers, mixers, active filters, and signal-conditioning circuits. The principal audio-oriented characteristics are 5 nV/√Hz typical equivalent input noise voltage at 1 kHz and a 10 MHz typical unity-gain bandwidth. According to the Texas Instruments product description, the NE5532 is a dual 30 V, 10 MHz low-noise operational amplifier. The device also provides 100 dB typical high dc voltage gain, a 32 V typical peak-to-peak output swing with ±18 V supplies, and a typical slew rate of 600 V/µs. The NE5532x family is internally compensated for unity-gain operation, reducing the external compensation components normally required around a high-speed amplifier. Its dual architecture allows two amplifier channels to share one package while retaining the low-noise characteristics sought in audio paths. Input-protection diodes, output short-circuit protection, and a high output-drive capability are identified in the manufacturer datasheet, making the device suitable for conventional low-frequency audio and general analog applications. Typical uses include stereo audio preamplification, mixing consoles, headphone-driver stages, active equalization filters, low-level audio signal conditioning, and instrumentation requiring low input noise. The dual configuration is especially useful where two related channels are required, such as left and right program paths. Its 10 MHz bandwidth also provides more than enough bandwidth for conventional audio while retaining useful response for other precision low-noise signal-chain work. When designing around the NE5532AD, verify the required output swing, input common-mode range, supply voltage, and stability at the selected gain against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left with open inputs. Source and sink capability should also be checked when driving a transformer, headphone stage, or capacitive load. This product record combines verified manufacturer and distributor information with practical engineering guidance, package and pinout details, pricing references, and a qualification of available drop-in alternatives. The comparison and application sections emphasize where the NE5532AD fits and where the available source evidence does not support claiming a true same-package replacement.

RFQ संपर्क
NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi
NE5532AD8

NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi

The onsemi NE5532AD8 is a dual high-performance, internally-compensated low-noise operational amplifier supplied in an 8-pin SOIC (SO-8, "D8" suffix) surface-mount package. The device integrates two independent op-amp channels with input-protection diodes, output short-circuit protection, very low equivalent input noise voltage of about 5 nV/√Hz typical at 1 kHz, a high unity-gain bandwidth of 10 MHz, a 9 V/µs slew rate, and a 600 Ω drive capability, all from a single dual-supply rail of ±3 V to ±20 V (or single-supply 6 V to 40 V). An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. It is the fundamental analog building block inside audio preamplifiers, active filters, instrumentation stages, servo loops, ADC input buffers, and DAC output I/V converters. The NE5532 family belongs to the "low-noise audio" op-amp class — a category that improves upon generic parts such as the 1458 by combining low voltage noise, wide bandwidth, and strong output drive into one device. Key features include low harmonic distortion (typically 0.002 % at 1 kHz into 600 Ω), high output current that can drive 600 Ω headphone loads directly, large output voltage swing (≈ ±13 V on ±15 V supplies), and excellent channel separation around 110 dB at 1 kHz. The "A" suffix denotes the higher-precision NE5532A variant with tighter input-offset voltage (typically 0.5 mV versus 0.5 mV for the non-A) and improved AC characteristics versus the original NE5532, while remaining pin-compatible with the standard NE5532 socket. Architecturally, the NE5532A uses a bipolar-junction input stage with emitter-degeneration resistors, a PNP common-emitter second stage, and an NPN class-AB output stage. Compensation is built into the die (no external capacitor required), which simplifies PCB design but caps stable unity-gain operation. Designers should treat the device as a "single-supply-unfriendly" part when planning ground-referenced single-rail circuits; a mid-rail bias is required for true ground sensing. Typical applications include high-fidelity audio preamplifiers, mixing consoles, microphone preamps, RIAA phono stages, line drivers, active crossovers, test-instrumentation signal conditioners, and ADC/DAC interface buffers. The 8-pin SOIC footprint is well-suited to high-density PCB designs and is one of the most widely supported DIP-socket IC sockets on adapter boards. When designing with the NE5532AD8, derate output current with increasing junction temperature, mind the input common-mode range that does not include the negative rail, and provide a solid ground pour for the exposed copper pad of the SOIC to keep the junction temperature below 150 °C. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi
NE5532AD8G

NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi

onsemi NE5532AD8G is a dual, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and two amplifier circuits in an 8-pin SOIC package. It is intended for audio, instrumentation, and control applications where low noise and improved output drive are important. The device is specified for dual supplies of ±3 V to ±20 V and commercial-temperature operation. A dual operational amplifier combines two independent amplifiers in one package. The NE5532A family belongs to the operational-amplifier hierarchy, within analog signal-conditioning and active-control systems. Its internally compensated design simplifies use in non-inverting, inverting, and feedback configurations without an external compensation network, while its low-noise characteristics make it useful when signal integrity must be preserved through amplification. The verified NE5532AD8G data identifies a 10 MHz gain-bandwidth product, 9 V/µs slew rate, 200 nA input-bias current, 500 µV input-offset voltage, 8 mA supply current, and a 3 V to 20 V supply range in the distributor listing. The dual SOIC package provides two circuits in one component, reducing board area compared with separate single amplifiers. Its improved output-drive capability and small-signal bandwidth distinguish it from basic general-purpose dual op amps. Typical uses include stereo audio preamplification, mixer stages, active filters, microphone and line-level signal conditioning, test equipment, and industrial control circuits. In audio designs, the low-noise architecture helps preserve quiet signal paths, while the 9 V/µs slew rate supports higher-frequency transients when the circuit bandwidth and load permit. In instrumentation applications, the two amplifiers can process complementary or sequential channels. The primary design consideration is supply and load compatibility. Confirm the dual-supply range against the system rails, check input and output swing limits for the selected gain, and place decoupling capacitors close to the supply pins. Stable feedback-network layout, adequate output-current capability, and thermal margin should be checked against the actual signal amplitude and frequency. No SOA applies because this is a linear operational amplifier rather than a power semiconductor.

RFQ संपर्क
NE5532AD8R2 - Dual 10MHz Low-Noise Op Amp | onsemi
NE5532AD8R2

NE5532AD8R2 - Dual 10MHz Low-Noise Op Amp | onsemi

The onsemi NE5532AD8R2 is an internally compensated, dual low-noise operational amplifier with a 10 MHz gain-bandwidth product, packaged in an 8-pin SOIC. It combines two amplifier channels in one package for audio, instrumentation, and general-purpose signal-processing circuits where low-noise performance and moderate bandwidth are important. The device operates from ±3 V to ±20 V and is specified at 38 mA per channel, with 200 nA of input bias current, 70 dB common-mode rejection ratio, and 1 µA maximum input offset current. An operational amplifier is an analog signal-processing IC that compares its inverting and non-inverting inputs and drives its output to amplify the difference between them. The NE5532 belongs to the internally compensated operational-amplifier family within the broader amplifier, analog IC, and semiconductor hierarchies. Internal compensation makes the amplifier stable without an external compensation network, simplifying conventional audio and instrumentation designs. Its dual-channel configuration reduces component count and board area when two gain stages are required. The NE5532AD8R2 is specifically described as a low-noise dual amplifier. Its 10 MHz gain-bandwidth product supports audio-frequency amplification and general closed-loop signal conditioning, while the 70 dB common-mode rejection helps reject common-mode disturbance on differential inputs. The low 200 nA input bias current can simplify biasing of higher-impedance source networks, although the supplied data does not establish input impedance, input capacitance, slew rate, or output-current capability. Typical uses include stereo audio preamplification, active equalization, low-level microphone-stage amplification, instrumentation buffering, and dual-channel analog filtering. In a preamplifier, the device can be configured as a non-inverting stage with feedback resistors, while the two internal channels can process left and right signal paths independently. In instrumentation circuits, the dual format can support gain and active filtering functions without requiring two separate amplifier packages. Designers should preserve the SOIC-8 footprint and verify the exact channel pin assignments against the manufacturer datasheet before layout release. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels require appropriate input termination rather than being left floating. Input and output swings, gain-bandwidth behavior, stability, and output-current limits must be checked against the circuit operating conditions. This page consolidates the verified onsemi and distributor information, provides package-level selection guidance, and distinguishes electrically similar candidates from confirmed drop-in replacements. Pricing, lifecycle classification, exact pin names, and several detailed electrical parameters remain explicitly marked where the supplied source data does not provide authoritative values.

RFQ संपर्क
NE5532AD8R2G - Dual Low-Noise Amplifier | onsemi
NE5532AD8R2G

NE5532AD8R2G - Dual Low-Noise Amplifier | onsemi

The onsemi NE5532AD8R2G is a dual, internally compensated, low-noise operational amplifier rated for 3 V to 20 V supply operation and supplied in an 8-pin SOIC package. It provides two amplifier channels in one package, making the device suitable for professional audio, instrumentation, signal conditioning, active filtering, test and measurement, and general-purpose analog designs. The verified distributor descriptions identify the NE5532AD8R2G as a standard general-purpose amplifier with two circuits and an 8-SOIC package. An operational amplifier is an analog building block that amplifies the voltage difference between its non-inverting and inverting inputs. Internally compensated operational amplifiers include frequency-compensation circuitry that establishes a stable operating characteristic without requiring an external compensation capacitor. Within the broader semiconductor hierarchy, an operational amplifier belongs to the linear-amplifier and signal-conditioning IC family, where low noise, output-current capability, slew rate, and input bias behavior determine its suitability for sensitive analog signals. The NE5532 family is specifically associated with low-noise audio and instrumentation operation. A dual-channel configuration reduces the number of packages required when two amplifier sections are needed, while the 8-pin SOIC format supports conventional surface-mount assembly. The Mouser listing specifies a 3 V to 20 V operating range, and the Arrow listing describes the device as a dual low-noise amplifier with an automotive AEC-Q100 option. These characteristics make the amplifier relevant to signal paths where low-noise performance and adequate output drive are more important than very small package area. The NE5532/SE5532 device family is described by onsemi as an internally compensated dual low-noise operational amplifier. Compared with general-purpose operational amplifiers, the NE5532 family was developed for improved noise performance and applications such as high-quality audio equipment and instrumentation. Two independent amplifiers can implement noninverting, inverting, summing, active-filter, buffer, and feedback-control stages, although each channel requires appropriate supply decoupling and feedback-network design. Typical applications include audio preamplifiers and mixer stages, microphone preamplification, active crossover and equalization networks, low-level sensor signal conditioning, laboratory instrumentation, oscilloscope input drivers, and audio interface circuits. In each case, the dual SOIC package can simplify board layout by placing two related amplifier functions close together. The low-noise characterization is particularly valuable when the source impedance is high or when the output must preserve small signals without adding unnecessary circuit noise. When designing around the NE5532AD8R2G, engineers should verify the exact input common-mode range, output swing, slew rate, input bias current, and channel-to-channel behavior against the manufacturer datasheet for the selected operating conditions. Input and output bypassing capacitors should be placed close to the relevant pins, and feedback components should be selected for the intended gain and bandwidth. Power-supply noise can also enter an audio or instrumentation path, so clean supply distribution remains as important as the amplifier itself. This product page combines the verified distributor and manufacturer-related source information with package, sourcing, comparison, and design guidance. It distinguishes published facts from unavailable parameters, preserves the original NE5532AD8R2G ordering code, and identifies only same-package drop-in candidates for engineering review. Final component selection should always include a full datasheet, pinout, and application-specific comparison before PCB substitution.

RFQ संपर्क
NE5532ADR - 30V, 10MHz Dual Low-Noise Op Amp | Texas Instruments
NE5532ADR

NE5532ADR - 30V, 10MHz Dual Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532ADR is a dual low-noise operational amplifier for audio applications, specified for ±5 V to ±15 V supplies, with a 10 MHz gain-bandwidth product and 9 V/µs slew rate, housed in an 8-pin SOIC package. The device combines two amplifiers in one package and is intended for low-noise audio preamplification, mixing, filtering, and similar signal-conditioning circuits. An operational amplifier is a voltage-feedback amplifier whose open-loop gain is used to create closed-loop gain with external feedback components. The low-noise operational amplifier category is part of the broader analog signal-processing hierarchy: operational amplifier, analog IC, and semiconductor. NE5532-family devices became established choices in audio circuitry because they combine low input noise, adequate bandwidth, high slew rate, and wide supply-voltage capability in a conventional through-hole-compatible or surface-mount package. Key verified attributes include a 30 V maximum supply rating, dual-amplifier configuration, 10 MHz bandwidth, 9 V/µs slew rate, and operation over ±5 V to ±15 V. According to the Texas Instruments manufacturer datasheet, the NE5532x grade is specified from 0°C to 70°C, while the electrically similar SA5532x grade extends the operating range to -40°C to +85°C. These distinctions matter when selecting between commercial-temperature and industrial-temperature versions. The NE5532ADR uses the standard dual-operational-amplifier arrangement, allowing each amplifier to be configured independently for non-inverting, inverting, summing, filtering, or active-amplifier functions. Its 8-pin SOIC package supports compact, surface-mount PCB construction while preserving a conventional dual-op-amp footprint. Designers should still verify output-current, output-voltage swing, input-bias-current, noise-density, and open-loop-gain requirements against the complete manufacturer electrical-characteristics tables. Typical applications include stereo audio preamplifiers, active crossover filters, microphone preamplifiers, line-level mixers, and small-signal audio output stages. Its 10 MHz bandwidth is well above the audible band, while its low-noise designation makes it appropriate for amplifying weak audio signals without adding unnecessary broadband noise. The 9 V/µs slew rate also helps preserve low distortion when processing larger transient waveforms. The primary design consideration is power-supply configuration. The manufacturer datasheet specifies operation from ±5 V to ±15 V, and dual-supply operation generally simplifies bipolar audio-signal handling around ground. Designers must observe the output-swing limits, avoid excessive capacitive loading, and maintain suitable decoupling close to the supply pins. Stable feedback networks and appropriately chosen compensation or load conditions are important for reliable closed-loop operation. This page combines verified manufacturer and distributor information with pinout guidance, practical application fit, drop-in comparison data, and engineering-focused selection notes. The comparison also distinguishes true pin-compatible options from devices that may sound different or require different supply and stability considerations.

RFQ संपर्क
NE5532ADRE4 - Dual 10MHz Low-Noise Op Amp for Audio | TI
NE5532ADRE4

NE5532ADRE4 - Dual 10MHz Low-Noise Op Amp for Audio | TI

The Texas Instruments NE5532ADRE4 is a dual, general-purpose low-noise operational amplifier with a 10 MHz unity-gain bandwidth, 9 V/µs slew rate, and typical equivalent input noise voltage of 5 nV/√Hz at 1 kHz, supplied in an 8-SOIC package. It is intended for audio applications operating from ±5 V to ±15 V, with the NE5532x grade specified over 0°C to 70°C. Both amplifier channels share the same compact surface-mount package, allowing one component to support stereo signal paths. A low-noise operational amplifier is an analog integrated circuit that amplifies voltage differences while contributing minimal intrinsic noise. The NE5532 belongs to the operational-amplifier hierarchy used for audio preamplification, mixing, buffering, filtering, and instrumentation. Its 5 nV/√Hz typical input-noise characteristic is especially relevant when the amplified signal is sourced from a high-impedance sensor or a low-level microphone. The device provides 10 MHz typical unity-gain bandwidth, 9 V/µs typical slew rate, 100 dB typical common-mode rejection, and 100 V/mV typical DC voltage gain. These characteristics support audio-band operation with ample bandwidth for feedback networks and active filters. The dual configuration reduces component count in stereo circuitry, while the 8-SOIC package is compatible with automated surface-mount assembly. The NE5532 uses a conventional voltage-feedback operational-amplifier architecture with two independent amplifiers. Each channel provides inverting and non-inverting inputs, an output, and a power-supply connection. Noise and common-mode rejection are important because they influence the signal-to-noise ratio and the degree to which unwanted supply or common-mode signals appear at the output. Operating from a dual supply also supports bipolar audio signals without biasing the source at mid-rail. Typical applications include stereo audio preamplifiers, microphone amplifiers, line-level mixers, tone-control circuits, active crossover networks, and low-level audio buffers. In each case, the low-noise input stage helps preserve small signals, while the 10 MHz bandwidth and 9 V/µs slew rate provide margin for gain and phase shaping. Designers must still verify stability with the selected feedback network and load. The principal design consideration is power-supply bypassing. Place the required input and output decoupling capacitors close to the device pins, keep output routing short, and avoid placing long traces beside noisy switching nodes. Decoupling values and stability guidance should be taken directly from the manufacturer datasheet and typical application circuit rather than inferred from the distributor summaries. This page combines verified manufacturer information, distributor pricing, pin-compatible substitute references, and practical application guidance. The alternatives are explicitly limited to same-package drop-in candidates, while unavailable electrical details remain marked for validation against each candidate manufacturer’s current datasheet.

RFQ संपर्क
NE5532ADRG4 - Dual 10 MHz Low-Noise Op Amp | Texas Instruments
NE5532ADRG4

NE5532ADRG4 - Dual 10 MHz Low-Noise Op Amp | Texas Instruments

Texas Instruments NE5532ADRG4 is a dual, general-purpose operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and 5 nV/√Hz typical equivalent input-noise voltage at 1 kHz, housed in an 8-pin SOIC package. The device provides two independent amplifiers and a 100 dB typical common-mode rejection ratio for audio, instrumentation, filtering, and low-level signal-conditioning applications. An operational amplifier is an active analog signal-conditioning device that uses high-gain differential feedback to amplify the difference between its two inputs. The dual NE5532 family belongs to the operational-amplifier hierarchy within analog and amplifier ICs. Its two channels can amplify noninverting and inverting signals independently, making it suitable for preamplifiers, active filters, mixers, buffers, and control loops where low noise, moderate bandwidth, and relatively high output-current capability are useful together. The NE5532ADRG4 combines a 10 MHz typical unity-gain bandwidth with 9 V/µs typical slew rate. Its typical high DC voltage gain is 100 V/mV, while the equivalent input-noise voltage is 5 nV/√Hz at 1 kHz. These characteristics support low-distortion audio signal paths and general feedback-control circuits without requiring a high-speed bipolar or current-feedback amplifier. Internally, the device uses a bipolar-compatible low-noise amplifier architecture intended for general-purpose precision audio work. Noise performance is especially important when the circuit handles microphone-level, musical-instrument, or balanced-line signals because amplifier noise can establish the input-referred noise floor. The common-mode rejection specification supports rejection of shared interference on differential inputs, while the two-amplifier configuration reduces package count in balanced and stereo circuits. Typical uses include stereo audio preamplification, active equalizer and crossover stages, microphone and line-level signal conditioning, instrumentation buffers, and low-frequency filter networks. In a preamplifier, both channels can process left and right signals while preserving low-noise performance. In an active filter, the 10 MHz bandwidth provides more open-loop capability than the audio-band signal being shaped, although stability must be verified for the selected noise gain and load. Designers should keep feedback-loop compensation appropriate for the selected gain, check output swing into the intended load, and provide stable decoupling at the supply pins. Because the available verified data does not state the complete supply-voltage range, input common-mode limits, output-current limits, or thermal resistance, those values must be confirmed in the manufacturer datasheet before final design release. This product page consolidates verified distributor specifications, pricing context, same-package replacement candidates, and application-oriented engineering guidance. It separates documented facts from unavailable parameters, helping engineers evaluate the NE5532ADRG4 quickly without mistaking an incomplete web summary for a complete electrical characterization.

RFQ संपर्क
NE5532AN - Dual Low-Noise 10 MHz Op Amp | onsemi
NE5532AN

NE5532AN - Dual Low-Noise 10 MHz Op Amp | onsemi

The onsemi NE5532AN is a dual, high-performance, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, supplied in an 8-pin DIP package measuring 0.300 inch (7.62 mm). Compared with standard general-purpose operational amplifiers, the NE5532 family provides improved noise performance, stronger output drive capability, and better small-signal and power-bandwidth performance. A low-noise operational amplifier is an analog signal-conditioning device that amplifies the voltage difference between its two inputs while seeking low added noise and low distortion. In the product hierarchy, the NE5532AN belongs to the operational-amplifier family, which is part of amplifier ICs and, more broadly, analog semiconductors. Its two amplifiers share one package while providing independent input, output, and supply connections. The principal verified characteristics include a dual amplifier configuration, internally compensated operation, a 10 MHz gain-bandwidth product, and an 8-DIP package. The associated NE5532x family is specified for operation over a ±5 V to ±15 V supply range. The commercial NE5532x temperature range is stated as 0°C to 70°C, while the SA5532x family is specified from -40°C to +85°C. Exact input-offset, input-bias-current, output-voltage, and output-current limits were not included in the supplied data and therefore remain unspecified on this page. Internally compensated operation allows each amplifier to operate as a stable closed-loop stage without an external compensation network. This simplifies analog circuit design while preserving the low-noise characteristics valued in audio equipment. The stronger output-drive capability described in the manufacturer data helps the amplifier maintain low distortion when driving the next stage or a termination load. The 10 MHz gain-bandwidth figure provides useful bandwidth for low-frequency signal conditioning and audio preamplification rather than high-speed instrumentation applications. Typical uses include stereo audio preamplifiers, active tone-control stages, mixer input stages, headphone-driver interfaces, active crossover filters, and low-level signal conditioning. Its dual configuration is particularly useful when a board needs two similar amplifier channels, such as left and right audio paths. For lower-voltage or extended-temperature requirements, the related SA5532x grade should be evaluated separately rather than assuming NE5532AN covers those conditions. The primary design consideration is supply-headroom management: the stated family specification applies from ±5 V to ±15 V, so the circuit must remain within that operating range at every temperature and load condition. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier in a dual package should be configured according to the manufacturer guidance rather than left floating. This page consolidates the verified package, supply-range, temperature-class, bandwidth, and cross-reference information for the NE5532AN, then adds application guidance, strict same-package drop-in comparisons, and practical selection criteria for engineers evaluating this dual low-noise operational amplifier.

RFQ संपर्क