उत्पाद (44,000+)

NE5532ANG - Dual Low-Noise 8-PDIP Op Amp | onsemi
NE5532ANG

NE5532ANG - Dual Low-Noise 8-PDIP Op Amp | onsemi

onsemi NE5532ANG is a dual, internally compensated low-noise operational amplifier with two amplifier circuits in an 8-pin PDIP package. Its specified operating supply range is 3 V to 20 V, and its design combines low-noise operation with the output-drive capability expected from the NE5532 family. The device is intended for audio and general-purpose signal-conditioning applications requiring two amplifiers in one package. Each integrated amplifier provides differential inputs, an output, and the usual dual-amplifier power connections in the standard 8-pin arrangement. An operational amplifier is a voltage-feedback amplifier that uses external feedback to control gain and signal behavior. A dual operational amplifier combines two amplifier channels in one package, reducing board area compared with separate single-channel devices. In the broader semiconductor hierarchy, the NE5532ANG belongs to the operational-amplifier family, which sits within amplifier ICs and analog signal-conditioning semiconductors. Its internal compensation simplifies implementation by allowing the manufacturer to establish stable operation without requiring a large external compensation network. The primary engineering benefits are low input noise, dual-channel integration, and an 8-pin PDIP package suitable for conventional through-hole PCB assembly. Two amplifier circuits can implement functions such as preamplification, filtering, buffering, active crossover stages, or audio channel processing in a single package. The onsemi listing identifies the NE5532ANG as a standard general-purpose amplifier, while the manufacturer datasheet describes it as an internally compensated dual low-noise operational amplifier. The NE5532 family is recognized for audio-focused signal-chain use, but its applications extend beyond simple volume control. Low-noise operation is valuable when the amplifier must preserve small signals without adding excessive broadband noise. Internal compensation supports practical feedback-based amplifier configurations, and the dual format allows a designer to use both amplifier sections for related analog functions rather than placing two separate packages on the board. Typical uses include stereo audio preamplification, headphone-driver signal stages, active equalizer and crossover circuits, low-level sensor amplification, and general instrumentation buffers. The same package can also support two independent channels in test equipment or measurement interfaces. Selection should be based on the required supply voltage, signal amplitude, output loading, noise target, stability in the selected feedback network, and the surrounding circuit impedance. For PCB implementation, follow the pin-description table in the manufacturer datasheet when assigning input, output, and supply traces. Place the manufacturer-recommended bypass capacitors close to the supply pins, keep input routing short and away from high-current switching nodes, and provide adequate output-current and thermal margin. Because the NE5532ANG is a through-hole PDIP device, verify the PCB drill pattern and pin-1 orientation rather than assuming a surface-mount footprint. This page combines the exact manufacturer and distributor identity of NE5532ANG with package-specific pin guidance, application-oriented circuit considerations, drop-in replacement analysis, and an explicit separation of confirmed characteristics from parameters that still require engineering verification.

RFQ संपर्क
NE5532AP - Dual Low-Noise Op Amp, 10MHz, 8-PDIP | Texas Instruments
NE5532AP

NE5532AP - Dual Low-Noise Op Amp, 10MHz, 8-PDIP | Texas Instruments

The Texas Instruments NE5532AP is a dual high-performance, low-noise operational amplifier supplied in an 8-pin PDIP (through-hole) package. Each of the two internal op-amps delivers 10 MHz unity-gain bandwidth, a 5 nV/√Hz input noise voltage at 1 kHz, 100 dB typical CMRR, and a 100 V/mV typical DC voltage gain. The device is specified for ±5 V to ±15 V dual supply operation and drives 600 ohm loads directly, making it a workhorse in professional and consumer audio designs. An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. Within the broader taxonomy, an op-amp belongs to the linear IC family -> amplifier ICs -> analog signal conditioning -> semiconductor. Low-noise audio-grade op-amps such as the NE5532 are designed to add minimal hiss and distortion when placed in the signal path of pre-amplifiers, mixers, equalizers, and line drivers, distinguishing them from general-purpose op-amps (e.g., TL072) that trade noise performance for cost or bandwidth. Key differentiating features of the NE5532AP include: 5 nV/√Hz equivalent input noise voltage (typ. at 1 kHz), 32 V peak-to-peak output swing with ±18 V supplies into 600 ohm, input protection diodes, output short-circuit protection, and a high slew rate that enables clean transient response in fast audio signals. The 8-PDIP package simplifies prototyping on breadboards and through-hole production boards, and is widely accepted in long-lifecycle industrial products where socketing and field replacement are valued. Architecturally, the NE5532 uses a bipolar transistor input stage and a class AB output stage. The bipolar front-end delivers the low voltage noise and high DC gain that JFET-input op-amps cannot match, at the cost of higher input bias current (which is acceptable in audio-coupling networks with series capacitors). The 600 ohm drive capability means the NE5532AP can directly feed pro-audio line inputs without an additional buffer. Typical applications include studio-quality microphone pre-amplifiers, mixing consoles, equalizer and crossover filter boards, audio DAC output buffers, headphone amplifiers, and instrumentation front-ends. The wide supply range also allows use in industrial control signal conditioning where dual rails are already present. When designing with the NE5532AP, observe the input common-mode range: the inputs must stay within the supply rails, and large differential voltages should be limited by external series resistance to avoid damaging the input-protection structures. Decouple both supply pins with 100 nF ceramics placed within 10 mm of the device. This page consolidates distributor pricing, drop-in DIP-8 alternatives, and practical audio design notes - information not assembled in the manufacturer datasheet alone - to support BOM decisions for new designs and legacy maintenance.

RFQ संपर्क
NE5532APG4 - 10MHz Dual Audio Op Amp | Texas Instruments
NE5532APG4

NE5532APG4 - 10MHz Dual Audio Op Amp | Texas Instruments

The Texas Instruments NE5532APG4 is a dual general-purpose operational amplifier with a 10 MHz gain-bandwidth product, supplied in an 8-pin dual in-line package. The verified distributor data identifies two amplifier circuits, a general-purpose audio classification, and a through-hole 8-DIP package measuring 0.300 inches with 7.62 mm lead pitch. One distributor reports a $0.6560 unit price and 4,320 pieces in stock as of 2026-10-22. An operational amplifier is an analog building block used to amplify voltage differences, buffer signals, filter noise, and drive feedback-controlled circuits. A dual amplifier contains two amplifier channels in one package. The NE5532 family is especially recognizable in audio signal paths because it is commonly associated with low-noise audio preamplification, mixing, and output-stage applications. Within the broader hierarchy, it is an amplifier IC, an analog integrated circuit, and a general-purpose semiconductor. The available data confirms two amplifier circuits and a 10 MHz bandwidth-related figure, while the manufacturer-specific electrical limits were not included in the supplied source set. Accordingly, specifications for supply voltage, input offset voltage, input-bias current, noise density, output swing, slew rate, operating temperature, and channel-to-channel matching are marked as needing primary-source verification. This conservative approach prevents generic NE5532-family figures from being presented as verified facts for this exact suffix and package. Its 8-DIP package is appropriate for prototypes, educational instruments, repair work, and through-hole audio boards where socketed replacement is useful. The larger package also makes the part straightforward to probe and exchange, although it occupies more PCB area than a surface-mount dual op amp. Circuit layout still requires short feedback paths, clean grounding, and appropriate supply bypassing to preserve stability and low-noise performance. Typical uses include stereo audio preamplification, active tone control, headphone-buffer stages, mixer input conditioning, and general low-frequency signal processing. These applications align with the device's stated general-purpose amplifier classification and dual-channel configuration. Exact stability, bandwidth, noise, and output-drive claims should be checked against the official Texas Instruments datasheet before setting gain-bandwidth requirements. For new designs, verify the exact NE5532APG4 suffix, supply rails, input common-mode range, output swing, and thermal conditions in the manufacturer datasheet. When repairing an existing board, preserve the original pin orientation and socket the device only after confirming that the installed part is electrically and mechanically compatible. The 7.62 mm pitch through-hole package is mechanically different from common SOIC-8 variants even where some signal functions resemble them. This page consolidates verified distributor availability, package information, pricing, cross-reference research, and practical replacement guidance beyond a raw distributor listing. Unknown electrical values are deliberately identified rather than inferred from the broader NE5532 family.

RFQ संपर्क
NE5532APS - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532APS

NE5532APS - Dual 10MHz Low-Noise Op Amp | Texas Instruments

Texas Instruments NE5532APS is a dual low-noise operational amplifier intended primarily for audio signal conditioning. The device provides two amplifiers, a 10 MHz gain-bandwidth product, and operation from ±5 V to ±15 V in an 8-pin SOP package. It is the surface-mount packaging option for the NE5532 family and is identified as an active product by the manufacturer’s product information. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to increase the difference between two input voltages. Operational amplifiers belong to the amplifier IC hierarchy and are commonly used in audio, control, measurement, and signal-processing circuits. The NE5532 family emphasizes low-noise performance, wide bandwidth, and practical dual-channel integration for applications requiring two similar amplifier functions in one package. The NE5532APS combines a 10 MHz gain-bandwidth product with a slew rate of 9 V/µs. Its specified supply range of ±5 V to ±15 V accommodates conventional bipolar analog rails, including ±12 V and ±15 V systems. The NE5532x grade is specified for operation from 0°C to 70°C, while the electrically related SA5532x family extends the operating range from -40°C to +85°C. The NE5532APS is packaged for surface-mount assembly in an 8-pin SOP configuration. Each internal amplifier has a differential input stage, a high-gain intermediate stage, and a push-pull output stage. The two amplifiers share supply pins but otherwise provide independent signal paths, allowing one device to implement stereo audio channels, balanced differential functions, active filtering, or a combination of buffering and gain. Stable operation around the unity-gain frequency and its 10 MHz bandwidth make it suitable for audio-frequency amplification and feedback networks. Typical uses include stereo audio preamplification, microphone preamplifiers, active crossover filters, line-level buffers, tone controls, and small-signal audio stages. It can also support low-frequency measurement or instrumentation circuits when the input signal remains within its common-mode and output-voltage limits. In each case, external resistor and capacitor networks determine the actual gain, bandwidth, and filtering response. The main design consideration is power-rail compatibility. The device expects bipolar supplies within ±5 V to ±15 V and does not operate from a single 5 V rail under its specified conditions. Designers should preserve input and output headroom, avoid excessive capacitive loading at the output, and select external feedback values that keep the closed-loop bandwidth and stability appropriate for the intended signal. This page combines the manufacturer’s device specifications with package details, sourcing guidance, application guidance, and an engineering-focused review of replacement considerations. It also distinguishes genuine pin-compatible options from devices that merely provide similar audio performance, helping designers avoid changes that require PCB or signal-path redesign.

RFQ संपर्क
NE5532APSR - Dual Low-Noise Op Amp | Texas Instruments
NE5532APSR

NE5532APSR - Dual Low-Noise Op Amp | Texas Instruments

Texas Instruments NE5532APSR is a dual, internally compensated, low-noise operational amplifier specified for ±5 V to ±15 V supplies in an 8-pin SOIC package. It provides two amplifiers per package, 5 nV/√Hz typical equivalent input noise at 1 kHz, a 10 MHz typical unity-gain bandwidth, 100 dB typical common-mode rejection, and a 9 V/µs typical slew rate. The NE5532APSR is intended for audio, instrumentation, and general-purpose signal-processing circuits where low noise, low distortion, and strong output-drive capability are important. An operational amplifier is an analog building block that amplifies the voltage difference between its inverting and non-inverting inputs. Its wider hierarchy includes voltage amplifiers, analog amplifiers, amplifiers, and semiconductor-based signal-conditioning ICs. The dual configuration provides two independent amplifiers in one package, reducing board area in audio preamplifiers, active filters, mixers, measurement equipment, and low-level sensor interfaces. Internally compensated devices are intended for stable unity-gain operation and commonly use negative feedback to set higher closed-loop gains. The NE5532 family combines low-noise operation with high output-drive capability and high unity-gain and maximum-output-swing bandwidths. According to the Texas Instruments NE5532x, SA5532x datasheet, the device also includes input-protection diodes and output short-circuit protection. Its 1 µA typical input bias current supports high-impedance signal sources, while 100 V/mV typical high dc voltage gain is useful for precision signal conditioning. The amplifier is designed for dual supplies, although its specified operating range includes lower total supply voltages than traditional ±15 V designs. The NE5532APSR is compensated for unity-gain operation and can be configured as a non-inverting or inverting amplifier with external feedback components. Noise performance is particularly important when the input signal is below the amplifier's own noise floor, while slew rate and bandwidth determine how accurately large or fast signals are reproduced. The 9 V/µs typical slew rate provides ample margin for many audio and instrumentation signals, but stability, output loading, and feedback-loop design remain critical at high frequencies and capacitive loads. Typical uses include stereo audio preamplifier stages, active low-pass and high-pass filters, audio mixers, low-level sensor amplifiers, oscilloscope input circuits, and laboratory instrumentation. The 8-pin SOIC package supports compact surface-mount layouts, while the dual amplifier organization reduces component count in stereo and dual-channel signal paths. In these applications, low equivalent input noise helps preserve low-level information, and output short-circuit protection improves robustness during overload or accidental output short conditions. Designers should verify input and output common-mode limits, output-current capability, load impedance, and supply headroom at the lowest expected input voltage. Place input, feedback, and output-loop connections to minimize parasitic capacitance and maintain clean grounding. Decoupling capacitors should be positioned close to the supply pins. When substituting a device, check DC offset, input bias current, output swing, bandwidth, slew rate, noise, and compensation stability rather than relying on package shape alone. This product page combines manufacturer specifications, package details, application guidance, alternative analysis, and practical circuit-design notes to support faster component evaluation. It is intended to help engineers compare the NE5532APSR against candidate dual low-noise amplifiers while preserving the integrity of an existing 8-pin SOIC layout.

RFQ संपर्क
NE5532APSRE4 - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532APSRE4

NE5532APSRE4 - Dual 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532APSRE4 is a dual general-purpose operational amplifier with a 10 MHz unity-gain bandwidth, 5 nV/√Hz typical equivalent input noise at 1 kHz, and a 100 dB typical common-mode rejection ratio. The device is supplied in an 8-pin SOIC package and operates from 0°C to 70°C. Each package contains two independent low-noise amplifiers suitable for audio, instrumentation, filtering, and general signal-conditioning applications. An operational amplifier is an analog integrated circuit that provides high open-loop gain and uses negative feedback to amplify, buffer, filter, or control voltage signals. Within the semiconductor hierarchy, the NE5532 belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC categories. It combines low voltage noise, high common-mode rejection, a 9 V/µs typical slew rate, and a 100 V/mV typical high DC voltage gain in a common surface-mount package. Key features include two amplifier circuits, 10 MHz typical gain-bandwidth product, 5 nV/√Hz typical input noise at 1 kHz, 100 dB typical CMRR, and a 15 V typical or maximum supply figure identified in the retrieved specifications. The 8-SOIC package measures approximately 5.30 mm in width according to the distributor listing. Tape-and-reel ordering is identified by the E4 suffix, making the part suitable for standard automated surface-mount assembly and replenishment processes. The device uses complementary input and output stages to deliver low-noise voltage amplification. Its unity-gain bandwidth makes it suitable for audio-frequency and moderate-bandwidth signal paths, while its high CMRR helps reject common-mode interference. The 9 V/µs slew rate supports reasonably rapid signal transitions. Designers should still verify output-voltage swing, input common-mode range, supply limits, and stability against their individual operating conditions before finalizing a circuit. Typical applications include stereo audio preamplifiers, active crossover and equalization networks, microphone-level conditioning, test-equipment input buffers, low-frequency active filters, and general-purpose analog signal processing. One amplifier section may drive or process one audio channel, allowing the dual package to support stereo or balanced two-channel circuitry while reducing board area. For stable operation, place the input, output, feedback, and compensation components close to the device and use a clean, low-impedance ground reference. Decoupling should follow the manufacturer datasheet recommendations. Avoid operating the amplifier at a gain where its internal compensation and board parasitics produce instability, and verify the common-mode input range whenever signals approach either supply rail. This product page consolidates the verified 10 MHz bandwidth, noise, CMRR, slew-rate, package, temperature, and observed distributor pricing data with application guidance, engineering design notes, and drop-in replacement information. It also distinguishes electrically useful alternatives from options that require pinout or application-specific verification.

RFQ संपर्क
NE5532D - Dual 10MHz Low-Noise Audio Op Amp | Texas Instruments (Tape & Reel)
NE5532D

NE5532D - Dual 10MHz Low-Noise Audio Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments NE5532D is a dual low-noise operational amplifier for audio applications, with two amplifier circuits, 5 nV/√Hz typical equivalent input noise at 1 kHz, and a 10 MHz typical unity-gain bandwidth in an 8-pin SOIC package. It is specified for total supply voltages from 10 V to 30 V, equivalent to ±5 V through ±15 V operation, making it suitable for conventional dual-polarity audio signal paths. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. Within the broader hierarchy, the NE5532 is a dual operational amplifier, a low-noise voltage-feedback amplifier, and a linear amplifier used in audio preamplifiers, mixing consoles, active filters, and line-level driver circuits. Its two independent channels make it suitable for stereo audio or paired mono signal processing. Key characteristics include 5 nV/√Hz typical input noise at 1 kHz, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, 10 V/μs typical slew rate, and a typical 100 dB common-mode rejection ratio. The device also provides rail-to-rail output swing under the specified load conditions and low-distortion operation. The manufacturer identifies the NE5532 family for audio applications rather than precision instrumentation or micropower systems. The NE5532x family uses a conventional bipolar operational-amplifier architecture optimized for low noise and audio bandwidth. Its performance depends on supply voltage, output loading, gain, frequency, and bypass-capacitor implementation. Because the specified operating range includes ±5 V to ±15 V, downstream circuit headroom and output-swing limits must be checked against the actual load rather than inferred from the nominal supply rating. Typical applications include stereo preamplifiers, headphone-buffer stages, active crossover filters, audio mixers, line amplifiers, and small-signal buffer circuits. The dual configuration reduces package count when two related audio channels are required. A design should still verify stability, output-current capability, thermal conditions, and the selected feedback network rather than assuming every audio circuit has the same optimum gain or loading. The primary design consideration is power-supply decoupling and clean grounding. Place suitable bypass capacitors close to the supply pins, keep input and feedback routing short, and avoid high-impedance nodes adjacent to the amplifier inputs. The SOIC-8 package is a surface-mount SOIC family package intended for PCB assembly rather than through-hole insertion. This page combines the verified manufacturer and distributor information for NE5532D with package, application, design, and procurement context. Alternative substitutions are shown only where the retrieved web material supports a credible cross-reference; unavailable pricing and electrical details remain explicitly marked rather than inferred.

RFQ संपर्क
NE5532D8 - Dual Low-Noise Op Amp | onsemi
NE5532D8

NE5532D8 - Dual Low-Noise Op Amp | onsemi

The onsemi NE5532D8 is a dual, internally compensated, low-noise operational amplifier packaged in an 8-pin SOIC. The verified product data identifies a 10 MHz gain-bandwidth product, a 3 V to 20 V supply range, and operation from ±3 V to ±20 V. Its two amplifiers share one package while providing independent input, output, and supply connections, making the device suitable for stereo audio, instrumentation, control, and telephone-channel applications. An operational amplifier is an analog integrated circuit that compares an input voltage with a feedback-derived reference and drives its output to reduce the difference between them. A dual operational amplifier combines two amplifiers in one package. Within the broader semiconductor hierarchy, this device belongs to the amplifier-IC family and supports precision analog signal conditioning when low noise, adequate bandwidth, and practical output-drive capability are important. The NE5532 family is specifically described as a high-performance, low-noise dual amplifier with improved noise performance, output drive, small-signal performance, and power-bandwidth behavior compared with standard devices such as the 1458. It is internally compensated for unity-gain operation, allowing use as a voltage follower without an external compensation network. The verified listing also associates the device with professional audio, instrumentation, control circuits, and telephone channel amplifiers. Use NE5532D8 where two related analog channels share one compact surface-mount package, particularly in low-noise audio signal paths. Its 10 MHz bandwidth provides more than enough bandwidth for many audio and general analog functions, while dual integration reduces component count compared with two separate single amplifiers. Designers should still verify gain, load, output swing, supply headroom, noise, and stability against the complete manufacturer datasheet before release. The D8 suffix identifies the verified 8-pin SOIC orderable offered by onsemi in the supplied distributor result. Place input and feedback components close to the relevant amplifier pins, maintain a continuous return path, and decouple the supply pins close to the package. Avoid leaving unused inputs floating; terminate them consistently with the chosen noise and bias-current strategy. This page consolidates verified distributor information, the manufacturer datasheet, strict package and pin constraints, and design guidance for NE5532D8. It distinguishes documented dual-amplifier functionality from unverified specifications by marking missing electrical details rather than estimating them.

RFQ संपर्क
NE5532D8G - Dual Low-Noise Operational Amplifier | onsemi
NE5532D8G

NE5532D8G - Dual Low-Noise Operational Amplifier | onsemi

onsemi NE5532D8G is a dual, internally compensated low-noise operational amplifier with two amplifier circuits, a 10 MHz gain-bandwidth product, and a 9 V/us slew rate in an 8-SOIC package. The verified distributor data identifies it as a general-purpose commercial-temperature amplifier covering 3 V to 20 V and classifying it for instrumentation, audio, and buffer-amplifier applications. A low-noise operational amplifier is a voltage-feedback amplifier designed to amplify weak signals while minimizing broadband noise. In the broader semiconductor hierarchy, the NE5532 belongs to operational amplifiers, analog amplifiers, integrated circuits, and signal-chain conditioning components. Its two integrated channels can process left and right audio signals, support instrumentation stages, or implement active filtering and buffering when the circuit operates within the manufacturer’s electrical limits. The principal verified features are dual-circuit integration, internal compensation, 1 uV input-noise class behavior, approximately 10 MHz bandwidth, and a 9 V/us slew rate. The low-noise characteristic is particularly useful in audio preamplifiers, where input-referred noise influences the audible signal floor. Its 10 MHz bandwidth also makes it more responsive than general-purpose precision amplifiers commonly used for slower instrumentation functions. Mouser describes the device as a dual low-noise commercial-temperature amplifier for a 3 V to 20 V supply range. The NE5532 architecture provides one amplifier per channel, with no external compensation network required. Verified sources describe low distortion, strong output-drive capability, high small-signal and power bandwidth, input-protection diodes, and output short-circuit protection. These characteristics make it suitable for preamplifier gain stages, active filters, instrumentation, test equipment, and general low-frequency analog signal conditioning. Exact noise density, input-offset voltage, common-mode range, output-current capability, and temperature limits require confirmation from the manufacturer datasheet. When laying out an NE5532D8G board, preserve the SOIC-8 land pattern and observe the manufacturer’s input, output, supply, and bypass recommendations. Place supply-decoupling capacitors close to the supply pins and use short, low-loop feedback paths to reduce oscillation risk. Because audio and instrumentation circuits are sensitive to grounding and supply noise, a quiet reference return, symmetrical routing, and appropriate output-load compatibility are as important as nominal gain calculations. This product page combines verified distributor identification, source-linked availability information, exact known electrical values, and explicit data markers for unsupported specifications. It is intended to help engineers distinguish verified NE5532D8G attributes from unverified claims before making an audio, instrumentation, or analog-signal-chain design decision.

RFQ संपर्क
NE5532D8R2 - Dual Low-Noise Op Amp | onsemi | Audio
NE5532D8R2

NE5532D8R2 - Dual Low-Noise Op Amp | onsemi | Audio

The onsemi NE5532D8R2 is a dual, internally compensated low-noise operational amplifier with two independent amplifiers in an 8-pin SOIC package. The verified distributor listing identifies the device as a standard general-purpose amplifier with a 2-circuit configuration and an 8-SOIC package. It is intended for audio, instrumentation, filtering, and signal-conditioning circuits where two channels and low-noise performance are useful. The verified sources also describe it as a 3 V to 20 V dual low-noise operational amplifier. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback. A dual operational amplifier contains two amplifier channels in one package, allowing a circuit to process two related signals or to build stereo, differential, or multi-stage analog functions. The internally compensated architecture simplifies stable operation in typical closed-loop analog applications, while the low-noise characteristics make the device relevant to audio and measurement circuits. The NE5532 family is commonly associated with audio preamplification, microphone stages, active filters, and general instrumentation. The verified search results specifically describe the NE5532D8R2 as an internally compensated dual low-noise operational amplifier and identify its package as 8-SOIC. They do not provide a complete manufacturer electrical table, so detailed values such as input noise density, slew rate, bandwidth, common-mode range, output swing, input bias current, and temperature limits are marked as data needed rather than inferred. Typical circuit implementation places each amplifier channel in a feedback network, with external resistors setting closed-loop gain and filtering behavior. Decoupling capacitors should be placed close to the supply pins, and the unused channel should be configured according to the manufacturer’s recommended practice rather than left floating. The SOIC footprint supports conventional surface-mount assembly, although actual board layout, thermal behavior, and signal integrity still require validation. NE5532D8R2 pricing and detailed electrical performance must be confirmed against current authorized distributor inventory and the manufacturer datasheet. The verified distributor page reports current purchasing access, but the supplied data does not include numeric prices, stock quantities, or lead times. This page therefore distinguishes verified catalog facts from specifications requiring datasheet confirmation.

RFQ संपर्क
NE5532D8R2G - 10 MHz Dual Low-Noise Op Amp | onsemi
NE5532D8R2G

NE5532D8R2G - 10 MHz Dual Low-Noise Op Amp | onsemi

The onsemi NE5532D8R2G is a dual, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, a 3 V to 20 V supply range, and an 8-SOIC package. It contains two amplifier circuits in one package and is classified as a standard general-purpose amplifier for commercial-temperature instrumentation, audio, filtering, and signal-conditioning equipment. An operational amplifier is a voltage-gain building block used within the broader semiconductor and analog integrated-circuit hierarchy. The NE5532 family combines low-noise voltage amplification with internally compensated operation, reducing the external compensation components normally required to stabilize a feedback amplifier. In signal paths, its role is to increase the voltage presented by a small source while preserving the intended signal bandwidth. The verified 10 MHz bandwidth supports applications requiring response beyond the audio baseband, while the dual circuit count lets one 8-SOIC package implement two independent amplifier sections. Its 3 V to 20 V operating supply span is suitable for conventional analog systems operating from regulated low-voltage rails through higher industrial-style supply voltages. The distributor listing specifically describes the device as an internally compensated dual low-noise operational amplifier. The NE5532 architecture is intended for general-purpose instrumentation rather than a specialized automotive-qualified product. Compared with the listed 10 MHz class of low-noise amplifiers, designers should examine noise density, distortion, output-current capability, input-bias current, unity-gain stability, and supply-current consumption against their exact circuit requirements. The verified data does not quantify every one of those electrical characteristics, so they should be confirmed in the manufacturer datasheet before final qualification. Typical uses include low-level audio preamplification, active filters, instrumentation signal conditioning, transducers, and general analog control loops. In each case, the device can provide two amplifier channels while maintaining a compact surface-mount footprint. The 8-SOIC format supports conventional PCB assembly and hand-soldering while avoiding the larger footprint of an equivalent dual DIP package. The principal design consideration is stability. Because the amplifier is internally compensated, a feedback network must be selected for the intended closed-loop gain and load. Designers should also verify output swing, input common-mode range, supply headroom, noise performance, and thermal margin using the manufacturer datasheet rather than relying on general NE5532-family assumptions. This page combines verified distributor availability and pricing, same-package replacement information, a parameter comparison, and practical selection guidance. It is intended to help engineers identify whether the NE5532D8R2G matches a dual, 8-SOIC, 10 MHz low-noise amplifier requirement before purchasing or redesigning an existing board.

RFQ संपर्क
NE5532DG - Dual Low-Noise Op Amp, 10 MHz, 16-SOIC | onsemi
NE5532DG

NE5532DG - Dual Low-Noise Op Amp, 10 MHz, 16-SOIC | onsemi

onsemi NE5532DG is an internally compensated dual low-noise operational amplifier with two independent amplifier circuits in a 16-SOIC surface-mount package. The device is specified for 3 V to 20 V operation, commercial-temperature applications, and operation from DC to 10 MHz. Its low-noise design, improved output-drive capability, and broader small-signal and power bandwidth make it a practical choice for high-quality audio, instrumentation, and control circuits. An operational amplifier is an analog signal-processing IC that uses high-gain differential feedback to amplify the voltage difference between its inputs. In this device category, the NE5532 family occupies the low-noise operational-amplifier tier of the broader voltage-amplifier and semiconductor hierarchy. It is intended for applications requiring cleaner signal amplification than standard general-purpose amplifiers while retaining the simplicity of an integrated, internally compensated dual amplifier. The NE5532DG provides two amplifier channels in one package, reducing board area compared with two separate single-channel devices. Its internally compensated architecture is intended to simplify closed-loop operation without requiring an external compensation network. The verified product information identifies bipolar construction, a maximum input offset voltage of 5 mV, a 10 MHz bandwidth rating, and low-noise performance appropriate to professional audio and measurement equipment. NE5532DG operates from a broad 3 V to 20 V supply range, allowing it to operate from conventional 5 V, 12 V, and 18 V analog rails. The wide supply range is useful in mixed industrial, consumer, and laboratory equipment, although the exact input and output swing limits must be taken from the manufacturer datasheet before finalizing a high-amplitude design. Because it is a bipolar amplifier, supply-current and common-mode behavior must also be checked against the system power budget. Typical uses include stereo audio preamplification, active filters, mixer input stages, audio buffers, sensor signal conditioning, laboratory instrumentation, and general feedback control. In each case, the two channels can amplify related signals or perform separate functions, while the low-noise internal design helps preserve small signals through the analog chain. Output loading, stability, and allowable output swing remain application-dependent. When placing NE5532DG on a PCB, place input, feedback, and decoupling connections to minimize parasitic pickup and maintain short feedback-loop paths. Follow the manufacturer’s recommended bypass capacitance and layout guidance, and verify stable operation with the actual source impedance, load, and supply configuration. Decoupling capacitors should be positioned close to the power pins to suppress supply ripple at the amplifier. This product page combines the verified distributor identity, package information, operating-range details, cross-reference findings, and practical design considerations. It distinguishes verified NE5532DG attributes from missing manufacturer-specific values and highlights the need to confirm exact pin names, noise density, slew rate, input bias current, output current, and lifecycle status in the current manufacturer documentation.

RFQ संपर्क
NE5532DR - Dual 10MHz Low-Noise Audio Op Amp | Texas Instruments
NE5532DR

NE5532DR - Dual 10MHz Low-Noise Audio Op Amp | Texas Instruments

The Texas Instruments NE5532DR is a dual low-noise operational amplifier for audio applications, with two amplifier circuits, 5 nV/√Hz typical equivalent input noise at 1 kHz, and a 10 MHz typical unity-gain bandwidth in an 8-pin SOIC package. It is specified for total supply voltages from 10 V to 30 V, equivalent to ±5 V through ±15 V operation, making it suitable for conventional dual-polarity audio signal paths. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. Within the broader hierarchy, the NE5532 is a dual operational amplifier, a low-noise voltage-feedback amplifier, and a linear amplifier used in audio preamplifiers, mixing consoles, active filters, and line-level driver circuits. Its two independent channels make it suitable for stereo audio or paired mono signal processing. Key characteristics include 5 nV/√Hz typical input noise at 1 kHz, 10 MHz typical unity-gain bandwidth, 100 dB typical DC voltage gain, 10 V/μs typical slew rate, and a typical 100 dB common-mode rejection ratio. The device also provides rail-to-rail output swing under the specified load conditions and low-distortion operation. The manufacturer identifies the NE5532 family for audio applications rather than precision instrumentation or micropower systems. The NE5532x family uses a conventional bipolar operational-amplifier architecture optimized for low noise and audio bandwidth. Its performance depends on supply voltage, output loading, gain, frequency, and bypass-capacitor implementation. Because the specified operating range includes ±5 V to ±15 V, downstream circuit headroom and output-swing limits must be checked against the actual load rather than inferred from the nominal supply rating. Typical applications include stereo preamplifiers, headphone-buffer stages, active crossover filters, audio mixers, line amplifiers, and small-signal buffer circuits. The dual configuration reduces package count when two related audio channels are required. A design should still verify stability, output-current capability, thermal conditions, and the selected feedback network rather than assuming every audio circuit has the same optimum gain or loading. The primary design consideration is power-supply decoupling and clean grounding. Place suitable bypass capacitors close to the supply pins, keep input and feedback routing short, and avoid high-impedance nodes adjacent to the amplifier inputs. The SOIC-8 package is a surface-mount SOIC family package intended for PCB assembly rather than through-hole insertion. This page combines the verified manufacturer and distributor information for NE5532DR with package, application, design, and procurement context. Alternative substitutions are shown only where the retrieved web material supports a credible cross-reference; unavailable pricing and electrical details remain explicitly marked rather than inferred.

RFQ संपर्क
NE5532DR2G - Dual 10 MHz Low-Noise Op Amp | onsemi
NE5532DR2G

NE5532DR2G - Dual 10 MHz Low-Noise Op Amp | onsemi

The onsemi NE5532DR2G is an internally compensated dual low-noise operational amplifier supplied in a 16-SOIC package. The verified product data identifies a 10 MHz gain-bandwidth product, low-noise performance, improved output drive capability, and substantially higher small-signal and power bandwidth than older standard amplifiers such as the 1458. Each package contains two amplifiers, allowing stereo audio, balanced signal, or dual-channel instrumentation designs to use one IC rather than two single-channel devices. An operational amplifier is a voltage-controlled voltage-source amplifier that uses negative feedback to make its closed-loop behavior stable and predictable. The NE5532 belongs to the low-noise operational-amplifier hierarchy within analog and linear ICs. Its dual-channel architecture is useful wherever two related signals must be amplified with matched circuitry, while internal compensation avoids an external compensation network in ordinary closed-loop applications. The verified material specifically describes better noise performance, improved output drive, and higher small-signal and power bandwidth than conventional operational amplifiers such as the 1458. These characteristics make the device relevant to audio preamplification, filtering, signal conditioning, buffering, current sensing, analog measurement, and precision control. Exact input-offset voltage, input-bias current, slew rate, supply-current, output-current, and noise-density values are not present in the supplied source records and therefore remain data-needed rather than inferred. The NE5532DR2G uses a 20 V maximum supply classification in the verified GlobalSpec record and is identified as a dual operational amplifier in a SOIC package. Its internally compensated architecture is suited to conventional negative-feedback loops, but the actual usable bandwidth still depends on closed-loop gain, load, output amplitude, supply voltage, and PCB layout. Designers should avoid driving capacitive loads directly unless stability has been verified at the intended frequency. Typical uses include stereo audio input stages, active filters, low-level sensor amplification, analog control loops, and precision signal-conditioning blocks. The dual format can reduce package count in stereo or differential circuits, but both channels share the same supply pins and common ground. Decoupling and grounding remain as important as nominal noise specifications because supply coupling and ground impedance can degrade otherwise quiet measurements. For PCB implementation, place the bypass capacitor close to the supply pins and preserve a short, low-impedance return path. Decoupling capacitance and voltage rating must be selected from the complete circuit requirements because the supplied records do not state a manufacturer-recommended value. Stable feedback components and suitable source and sink loads are equally important when using the amplifier outside the manufacturer datasheet's exact test conditions. This page consolidates the verified distributor and source-page information, separates confirmed data from missing specifications, and adds engineering-focused application and design guidance. Distributor pricing and stock can change independently of the device, so the listed LCSC price is identified as a point-in-time commercial reference rather than a guaranteed quotation.

RFQ संपर्क
NE5532DRG4 - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532DRG4

NE5532DRG4 - Dual 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532DRG4 is a dual, general-purpose operational amplifier with a 30 V power-supply rating, 10 MHz gain-bandwidth product, and 5 nV/√Hz typical input-noise voltage at 1 kHz, packaged in an 8-SOIC. It combines low noise, high slew rate, and substantial output-drive capability for audio signal paths. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its two inputs. Within the broader semiconductor hierarchy, this audio operational amplifier belongs to amplifier ICs and supports precision gain, buffering, active filtering, and low-distortion signal conditioning. The NE5532 contains two independent amplifiers while sharing one IC package and supply rails. Verified headline characteristics include a 9 V/µs slew rate, 10 MHz typical unity-gain bandwidth, and 100 dB typical common-mode rejection. Its 5 nV/√Hz typical input-noise density at 1 kHz makes it especially useful when amplifier noise would otherwise limit audio or instrumentation performance. Input-protection diodes and output short-circuit protection support practical general-purpose use. The NE5532 operates from ±5 V to ±18 V according to the cited product information, with a maximum total supply voltage of 30 V. It is intended for audio applications but can also implement microphone preamplifiers, active crossovers, line-level stages, filters, buffers, and low-frequency measurement circuits. The dual configuration reduces package count when two gain stages are required. For stable operation with a minimal external network, place the manufacturer-recommended bypass capacitors close to the supply pins and route traces away from noisy power and digital signals. Input and output impedance, load capability, output swing, distortion, and common-mode headroom determine the usable bandwidth. Do not assume the 10 MHz small-signal bandwidth remains available at every gain, voltage, and load condition. NE5532DRG4 is supplied in tape-and-reel packaging for automated assembly. This page combines verified distributor information, the Texas Instruments product description, same-package substitution guidance, and practical design notes to support sourcing and engineering selection without implying that merely similar amplifiers are automatically drop-in replacements. A pin-to-pin alternative must match the dual 8-SOIC footprint and pin functions as well as the voltage, bandwidth, noise, slew-rate, and drive requirements. Circuit-level substitution should also verify supply rails, gain configuration, output loading, distortion, stability, and intended audio performance. The comparisons below distinguish verified facts from parameters that still require manufacturer-specific confirmation.

RFQ संपर्क
NE5532DX - Dual Low-Noise Op Amp, 8-SOIC | onsemi
NE5532DX

NE5532DX - Dual Low-Noise Op Amp, 8-SOIC | onsemi

The onsemi NE5532DX is a dual, general-purpose operational amplifier with two independent amplifier circuits, an 8-SOIC package, an 8 V/µs slew rate, and a 10 MHz gain-bandwidth product. It is supplied in tape-and-reel packaging and combines internally compensated operation with low-noise performance suited to audio and instrumentation. An operational amplifier is a high-gain, differential-input analog IC that uses external feedback to control gain, bandwidth, and signal conditioning. The NE5532 belongs to the broader hierarchy of operational amplifiers, analog signal-chain ICs, and semiconductors. Internally compensated dual amplifiers simplify closed-loop design because no external compensation network is required for ordinary voltage-feedback applications. The verified device data identifies a gain-bandwidth product of 10 MHz, slew rate of 8 V/µs, and full-power bandwidth of 140 kHz. These figures make the part useful for high-quality audio preamplification, active filtering, microphone conditioning, and general instrumentation. Its dual configuration also reduces board area by placing two amplifiers in one package. The NE5532 architecture provides improved noise performance, output-drive capability, and small-signal bandwidth compared with standard general-purpose amplifiers. Internal frequency compensation supports stable operation with conventional feedback networks, while the two amplifier channels can process independent signals or work together in differential and filtering circuits. Typical uses include professional audio input stages, low-level sensor amplification, telephone-channel amplification, active crossover networks, and control circuits. When using the part in audio equipment, input impedance and source impedance should be considered alongside the gain-bandwidth product. Higher closed-loop gains reduce usable bandwidth, so the amplifier should not be treated as a wideband op amp merely because its gain-bandwidth product is 10 MHz. For PCB implementation, decouple each power pin with a local high-frequency bypass capacitor and keep return-current paths short. Input and feedback traces should be physically separated to reduce parasitic coupling. The 8-SOIC package is leaded and readily hand-solderable, but careful thermal design is still required when driving low-impedance loads continuously. This product record combines verified NE5532DX specifications, distributor availability references, package details, cross-reference alternatives, and application-focused design guidance. It distinguishes electrical compatibility from mere functional similarity and identifies where replacement parameters require verification before production use.

RFQ संपर्क
NE5532N - Dual Low-Noise Op Amp, 10 MHz, 8-PDIP | onsemi
NE5532N

NE5532N - Dual Low-Noise Op Amp, 10 MHz, 8-PDIP | onsemi

The onsemi NE5532N is a dual, internally compensated, general-purpose operational amplifier with two amplifiers in an 8-PDIP package. Verified source data identifies a gain-bandwidth product of 10 MHz and slew rate of 9 V/µs. Its low-noise design, improved output-drive capability, and higher small-signal and power bandwidth make it suitable for high-quality audio amplification, active filtering, control loops, and telephone signal paths. An operational amplifier is a voltage-gain building block used within the broader analog-amplifier and semiconductor hierarchy. The NE5532 combines differential inputs, high open-loop gain, internal frequency compensation, and output-drive capability in one dual amplifier. Two independent amplifier sections in one package reduce board area and simplify dual-channel or stereo circuitry, while requiring careful treatment of supply rails and grounding. The verified listing describes the NE5532 as a dual high-performance low-noise operational amplifier. Internally compensated operation simplifies stable feedback-network design, particularly in audio preamplifiers and crossover filters. A 10 MHz gain-bandwidth product supports wider-bandwidth signal processing than common low-frequency general-purpose amplifiers, while the 9 V/µs slew rate gives finite large-signal response that must still be checked against the required load and signal amplitude. The NE5532 family is associated with low-noise audio and control applications. Each package contains two amplifier channels, allowing one IC to implement stereo input stages, microphone preamplifiers, active equalizers, crossover filters, line buffers, or small-signal control circuits. The verified distributor listing classifies NE5532N as a standard general-purpose amplifier with two circuits in an 8-PDIP package and tube packaging. For design implementation, use the manufacturer's specified supply voltage, common-mode limits, output-current capability, input-bias-current behavior, noise figures, and compensation guidance. Decoupling capacitors should be placed close to the supply pins, and analog-signal routing should avoid noisy switching nodes and high-impedance traces. Verify stability at the intended gain, load capacitance, output amplitude, and temperature rather than relying only on nominal bandwidth. This page combines the verified package, bandwidth, slew-rate, distributor, and cross-reference information with practical selection guidance. It distinguishes verified facts from parameters requiring confirmation from the applicable manufacturer datasheet, helping engineers identify NE5532N without assuming undocumented electrical limits.

RFQ संपर्क
NE5532NG - Dual Low-Noise 10 MHz Op Amp | onsemi
NE5532NG

NE5532NG - Dual Low-Noise 10 MHz Op Amp | onsemi

The onsemi NE5532NG is a dual, internally compensated, general-purpose operational amplifier with a 10 MHz gain-bandwidth product, a 3 V to 20 V supply range, and an 8-pin PDIP package. It is designed for audio and general signal-conditioning circuits that require low-noise amplification, high unity-gain bandwidth, and adequate output-drive capability. The dual configuration provides two amplifiers in one package, reducing board area and simplifying dual-channel layouts. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between voltages applied to its input terminals. The NE5532NG belongs to the operational-amplifier hierarchy: dual operational amplifier, voltage-feedback amplifier, amplifier IC, and ultimately analog semiconductor. Its internal compensation avoids an external compensation network in typical closed-loop configurations, which helps simplify designs while maintaining stable operation. The verified manufacturer information identifies the NE5532NG as an internally compensated dual low-noise operational amplifier. The family is described as offering better noise performance than standard amplifiers such as the 1458, while also combining excellent DC and AC characteristics with high output-drive capability, high unity-gain and maximum-output-swing bandwidth, low distortion, high slew rate, and input-protection diodes. These characteristics suit precision audio stages, active filters, buffers, and general instrumentation. The 10 MHz gain-bandwidth product provides useful bandwidth for audio-frequency and moderate-frequency signal paths. The 3 V to 20 V supply-voltage span accommodates conventional analog rails, although the selected dual-supply arrangement must remain within that range. Because the NE5532NG is supplied in an 8-pin PDIP package, it is particularly suitable for leaded through-hole assemblies, prototypes, repair work, and production boards designed around a DIP footprint. Typical applications include stereo audio preamplification, microphone-stage amplification, active equalization filters, line-level buffers, tone-control circuits, and instrumentation signal conditioning. In dual-channel audio designs, both amplifier sections can be used symmetrically for left and right signal paths. The device is also useful where low distortion and low noise are more important than the very low power consumption or small footprint of newer CMOS amplifiers. For a new design, confirm the exact load impedance, output swing, supply configuration, input common-mode range, input bias current, slew rate, and noise spectrum from the manufacturer datasheet before committing the circuit. Decoupling capacitors should be placed close to the supply pins, and the unused channel should be configured according to the datasheet rather than left floating. This page consolidates verified distributor and manufacturer information, same-footprint replacement candidates, comparison parameters, and practical design cautions. It distinguishes confirmed values from parameters that still require verification, helping engineers move from part selection to a defensible circuit design without relying on unverified generic amplifier claims.

RFQ संपर्क
NE5532P - Dual 10 MHz Low-Noise Op Amp | Texas Instruments
NE5532P

NE5532P - Dual 10 MHz Low-Noise Op Amp | Texas Instruments

Texas Instruments NE5532P is a dual low-noise operational amplifier intended for audio applications, with two amplifier circuits in an 8-pin PDIP package. Verified device information identifies 10 MHz typical unity-gain bandwidth, 9 V/µs typical slew rate, operation from ±5 V to ±15 V, and a 30 V maximum supply rating. The device combines low-noise input characteristics with adequate bandwidth and output drive for preamplifiers, active filters, mixers, and audio buffers. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification and negative feedback to process signals from audio, instrumentation, communications, and control systems. The NE5532 belongs to the dual low-noise operational-amplifier family and contains two independent amplifiers, allowing stereo audio or dual-channel filtering in one package. Its PDIP format is useful for prototypes, repair work, and through-hole audio boards where accessibility and replaceability matter. Verified sources describe NE5532P as a dual, 30-V, 10-MHz low-noise operational amplifier for audio applications. Additional reported characteristics include 5 nV/√Hz typical equivalent input noise at 1 kHz, 100 dB typical common-mode rejection ratio, and 100 V/mV typical high dc voltage gain. These characteristics support low-level signal amplification where audible noise and channel imbalance could affect performance. Exact limits and test conditions should be confirmed in the manufacturer datasheet. The 10 MHz unity-gain bandwidth gives the device useful signal-path range beyond audio baseband, while the 9 V/µs slew rate helps preserve large-signal waveform shape. Nevertheless, actual distortion, output swing, noise, and stability depend on supply voltage, load, feedback topology, output coupling, PCB layout, and the surrounding passive components. The 30 V device rating should not be confused with a recommended operating supply. Typical NE5532P applications include stereo audio preamplification, active crossover and equalizer filters, low-impedance audio buffers, active balancing networks, and low-level signal conditioning. It may also be used in oscillators and test circuits where a dual amplifier provides two coordinated channels. Bypass each supply pin close to the IC and keep feedback components and sensitive input routes compact. This page consolidates verified manufacturer and distributor information, cross-reference results, and design guidance for engineers evaluating the NE5532P. Alternative listings are limited to candidates supported by the supplied web data and must be checked for exact pinout, package, supply range, noise, bandwidth, and load compatibility before substitution.

RFQ संपर्क
NE5532PE4 - Dual 30V 10MHz Low-Noise Op Amp | Texas Instruments
NE5532PE4

NE5532PE4 - Dual 30V 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532PE4 is a dual, general-purpose low-noise operational amplifier specified for a 30 V maximum total supply and 10 MHz unity-gain bandwidth, with two amplifiers in an 8-pin PDIP package. Typical input noise is listed at 5 nV/√Hz at 1 kHz, while the device is designed specifically for audio applications where low noise, adequate output drive, and low distortion are important. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify voltage differences. The NE5532 belongs to the voltage-feedback operational-amplifier family and sits within the broader amplifier IC and analog signal-chain hierarchy. Two independent amplifiers in one package reduce board area in stereo, mixer, preamplifier, crossover, and active-filter circuits, provided the power-supply and decoupling requirements are met. The verified specifications identify a 10 MHz typical unity-gain bandwidth, 9 V/µs typical slew rate, 100 dB typical common-mode rejection ratio, 100 V/mV typical high DC voltage gain, 800 nA typical input bias current, and 500 µV typical offset voltage. Its low-noise architecture supports audio preamplification and other precision analog stages, while its 30 V total-power specification suits higher-voltage signal paths when the actual operating conditions remain within the manufacturer’s absolute maximum ratings. The NE5532 is voltage-feedback compensated, making feedback-network design and stability analysis conventional for audio applications. Input-protection diodes and output short-circuit protection are identified in the product description. Designers must still verify supply polarity, input common-mode range, output swing, operating temperature, package tolerances, and stability against the complete manufacturer datasheet before releasing production hardware. Typical uses include stereo line preamplifiers, active crossover networks, microphone preamplifiers, headphone-driver signal stages, audio mixers, and instrumentation blocks requiring low-noise amplification. In each case, the 10 MHz bandwidth and 9 V/µs slew rate provide headroom for audio-band signals, while the dual package simplifies balanced or multi-channel layouts. For PCB design, keep the power-supply bypass capacitor close to the supply pins, use short feedback paths, and provide adequate ground return current. Decoupling and compensation values should follow the manufacturer’s recommended circuit rather than assumptions based only on the headline bandwidth. Verify the selected NE5532PE4 supply voltage and load conditions against the datasheet limits. This product page consolidates the verified Texas Instruments family specifications, distributor availability, source links, and practical guidance for engineers evaluating the NE5532PE4. It also distinguishes confirmed values from parameters that require confirmation from the full manufacturer datasheet or authorized distributor documentation.

RFQ संपर्क
NE5532PSR - Dual 10 MHz Low-Noise Audio Op Amp | Texas Instruments
NE5532PSR

NE5532PSR - Dual 10 MHz Low-Noise Audio Op Amp | Texas Instruments

The Texas Instruments NE5532PSR is a dual low-noise operational amplifier for audio applications, with a 10 MHz typical unity-gain bandwidth, 5 nV/Hz typical equivalent input noise voltage at 1 kHz, and an 8-pin SOIC package. Designed for high-performance audio signal chains, it combines low distortion with high output-drive capability, a typical 9 V/µs slew rate, and a typical 100 dB common-mode rejection ratio. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to create stable, precise gain. The NE5532 belongs to the dual-operational-amplifier, voltage-feedback, low-noise operational-amplifier hierarchy and is widely used in professional audio, preamplifier, mixer, filter, and signal-conditioning circuits. Its two independent amplifiers share the same package while providing separate input, output, and supply connections. The NE5532 family's key characteristics include a typical 10 MHz unity-gain bandwidth, 5 nV/√Hz input noise at 1 kHz, and a typical 100 dB common-mode rejection ratio. It also provides a typical high DC voltage gain of 100 V/mV and an output swing specified at 32 V peak-to-peak under ±18 V supplies and 600 Ω loading. The listed 9 V/µs slew rate supports faithful reproduction of higher-frequency audio and waveform signals. Internally compensated for unity gain, the amplifier simplifies conventional audio-board design because no external frequency-compensation network is required. Input-protection diodes and output short-circuit protection improve robustness, while low distortion and high slew rate make the device suitable for demanding small-signal stages. The verified operating-temperature range shown for NE5532PSR is 0°C to 70°C, corresponding to its standard general-purpose product classification. Typical uses include stereo preamplification, active crossover and equalizer circuits, mixing consoles, headphone-buffer stages, audio test equipment, and general low-noise signal conditioning. In each case, the NE5532 can be paired with external resistors and capacitors to establish gain, bandwidth, and filtering. The dual configuration reduces board area when two audio channels must be processed with matching device characteristics. Designers should account for supply headroom, output-current limits, stability, and the operating region of the chosen feedback network. Decoupling capacitors should be placed close to the supply pins, while input and feedback resistors should avoid long high-impedance traces that increase noise pickup. The 8-SO surface-mount package also requires adequate solderability and assembly controls for automated production. This product record consolidates verified manufacturer and distributor information, current pricing references, same-family alternatives, and application-specific engineering guidance. It adds practical comparison and design context beyond the basic distributor listing while clearly separating verified specifications from values that still require confirmation from an individual alternative's datasheet.

RFQ संपर्क
NE5534AD - 30V 10MHz Low-Noise Amplifier | onsemi
NE5534AD

NE5534AD - 30V 10MHz Low-Noise Amplifier | onsemi

The onsemi NE5534AD is a single low-noise operational amplifier designed for audio and precision analog signal chains, with a 30 V supply rating, 10 MHz gain-bandwidth product, and 6 nV/√Hz equivalent input noise voltage. The device is offered in an 8-pin SOIC package and is suitable for microphone preamplification, active filtering, audio mixing, instrumentation, and signal-conditioning applications. The NE5534A family provides low distortion, input-protection diodes, output short-circuit protection, and offset-voltage nulling through the BALANCE and COMP/BAL pins. These characteristics make the NE5534AD a conventional bipolar audio amplifier choice where low noise and established external compensation behavior are important. The operating range is intended to support traditional analog supply voltages found in professional audio, consumer audio, laboratory, and industrial equipment. The 10 MHz bandwidth provides useful bandwidth for low-frequency audio and general-purpose feedback-network design, while the 6 nV/√Hz noise specification supports quiet amplification of low-level source signals. The 8-pin SOIC package also simplifies assembly into conventional through-hole-style PCB layouts. Designers should review the manufacturer datasheet for input offset voltage, input bias current, output swing, slew rate, compensation requirements, supply-current behavior, and package details before finalizing a production design. This page combines verified manufacturer and distributor information with practical guidance for evaluating the NE5534AD as a drop-in operational-amplifier option.

RFQ संपर्क
NE5534ADG - Low-Noise 10MHz Op Amp | onsemi | Audio
NE5534ADG

NE5534ADG - Low-Noise 10MHz Op Amp | onsemi | Audio

The onsemi NE5534ADG is a single, low-noise operational amplifier with a 3 V to 20 V supply range, 10 MHz gain-bandwidth product, and 13 V/us slew rate, housed in an 8-pin SOIC package. The NE5534ADG is designed for audio, control, and instrumentation circuits that require low-noise amplification, moderate bandwidth, and strong output-drive capability. Its single-amplifier configuration is particularly useful when a board needs one precision analog channel rather than a dual or quad device. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to create stable signal-processing functions. The NE5534 family combines a bipolar input stage with internal frequency compensation, placing it in the general-purpose operational-amplifier hierarchy. This makes the device useful for audio preamplification, active filtering, buffer amplification, and low-frequency instrumentation while remaining distinct from CMOS rail-to-rail amplifiers designed for very-low-voltage or micropower systems. The principal strengths are low input noise, a 10 MHz gain-bandwidth product, and 13 V/us slew rate. The bandwidth supports accurate amplification of audio-band and other moderate-frequency signals, while the slew rate helps preserve large-signal fidelity in filters, mixers, and control paths. The NE5534 family also offers improved output-drive capability compared with common TL08x-class amplifiers, making it a practical choice when the output must drive a moderately demanding load. According to the onsemi datasheet, the amplifier is internally compensated for stable operation at gain values of one or higher and is specified as a single general-purpose amplifier. The device operates from 3 V to 20 V, allowing its use in conventional single-supply and dual-supply analog systems. The 8-SOIC package measures approximately 0.154 inch, or 3.90 mm, in body width and supports conventional surface-mount assembly. Typical applications include audio mixer input stages, low-noise voltage buffers, active low-pass and band-pass filters, servo-control loops, and instrumentation signal conditioning. In an audio preamplifier, the amplifier can provide channel gain while its low-noise characteristic helps preserve the signal floor. In an active filter, the 10 MHz gain-bandwidth product and 13 V/us slew rate provide useful headroom beyond the audible range, while compensation and feedback stability determine the usable filter bandwidth. Designers should use the manufacturer datasheet pin-description table when assigning tracks and should preserve the specified compensation and supply arrangements. Input and output layout should minimize parasitic capacitance, maintain short feedback paths, and decouple the supply pins close to the device. Stable operation also depends on correct feedback polarity and suitable output-load conditions; compensation pins must not be treated as general-purpose signal inputs. This product page combines the exact NE5534ADG identity, package information, electrical characteristics, verified sourcing links, and engineering guidance with a practical comparison of documented equivalents. It is intended to help engineers identify the correct low-noise single amplifier, confirm footprint compatibility, and plan the surrounding filter, decoupling, and signal-conditioning circuitry.

RFQ संपर्क
NE5534ADR - 30V 10MHz Low-Noise Op Amp | Texas Instruments
NE5534ADR

NE5534ADR - 30V 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5534ADR is a single low-noise operational amplifier with a 30 V maximum supply voltage, 10 MHz gain-bandwidth product, and 38 mA output-current capability, packaged in an 8-pin SOIC. Designed for audio and general-purpose analog signal paths, the NE5534ADR combines low-noise operation with the output drive required by audio buffers, mixing stages, and precision analog circuits. An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to control gain and bandwidth. The NE5534 belongs to the low-noise operational-amplifier category and therefore serves as a building block within the broader voltage-amplifier and signal-conditioning hierarchy. Its application role is to increase signal amplitude without adding substantial noise or distortion. The principal device ratings are a 10 MHz unity-gain bandwidth and a maximum 30 V supply voltage. The manufacturer describes the NE5534 as a single amplifier intended specifically for audio applications. Its 38 mA output-current capability provides useful drive for moderate-load analog stages. The NE5534ADR ordering code also identifies the standard amplifier, single-circuit configuration, and 8-pin SOIC construction described for this part. In an audio signal chain, the NE5534ADR can serve as a low-noise preamplifier, voltage follower, or buffer between a source and a downstream audio circuit. Its 10 MHz bandwidth provides ample signal-path capability for audio applications, while its low-noise design helps preserve the signal floor of high-fidelity equipment. The 38 mA output-drive specification makes it more suitable for these tasks than a strictly low-power micropower amplifier. The NE5534ADR is also appropriate for general instrumentation, active filtering, and signal-conditioning designs where low noise, adequate bandwidth, and output drive are the main priorities. Because the device is a single amplifier, systems requiring several independent channels must use multiple devices and must account for each package separately during PCB planning. When laying out an NE5534ADR circuit, place the input and output components close to their corresponding pins and maintain a common ground reference to minimize unwanted pickup. Decoupling capacitors should be positioned near the power pins. Designers must also observe the maximum 30 V supply rating and confirm the actual power-supply voltage, output swing, load, and thermal conditions against the manufacturer datasheet before production release.

RFQ संपर्क