उत्पाद (46,000+)

THS6093CD - 275mA +12V ADSL Line Driver | Texas Instruments
THS6093CD

THS6093CD - 275mA +12V ADSL Line Driver | Texas Instruments

The Texas Instruments THS6093CD is a 275 mA, +12 V ADSL CPE and PLC line driver with shutdown, packaged in a 14-pin SOIC. It is designed for high-speed line-driving applications using either a 1:2 transformer ratio or single-supply operation. Its headline characteristics are 275 mA output current, +12 V supply operation, a 14-SOIC package, low 2.1 pA/√Hz noninverting current noise, and a shutdown function. An ADSL line driver is an interface integrated circuit that converts upstream data signals into suitable current and voltage levels for transmission over copper lines. It belongs to the interface IC hierarchy within integrated circuits and semiconductor signal-conditioning devices. The THS6093 is intended for full-rate ADSL and G.Lite equipment, including customer-premises equipment and power-line communication equipment where the line interface must combine high output current with controlled noise. Key features include compatibility with a 1:2 transformer ratio, a wide supply-voltage range, and suitability for single +12 V operation. The 275 mA output capability provides useful drive current for line termination and transformer coupling. The device also includes shutdown control, allowing a system to disable the driver when line transmission is not required. Low noninverting current noise of 2.1 pA/√Hz helps reduce noise coupled through a telephone hybrid into the downstream receiver path. The THS6093 uses a high-current output stage suited to the demanding load presented by an ADSL line interface. Its architecture supports both transformer-coupled and single-supply arrangements, giving designers flexibility in line-network topology. The 14-pin SOIC package is a conventional surface-mount format suitable for automated PCB assembly, although the high-current output path requires careful routing, thermal review, and adequate copper around the power and ground pins. Typical uses include ADSL CPE line interfaces, full-rate ADSL modems, G.Lite access equipment, PLC gateways, and communications terminals connected to copper lines. It is particularly relevant when the design needs a dedicated line driver with a shutdown control and operation from a +12 V supply rather than a general-purpose low-power amplifier. For PCB implementation, place the device close to the line-transformancer or network interface and keep the high-current output path compact. Use a low-inductance supply connection and adequate input and output bypassing according to the manufacturer application guidance. Verify maximum output current, voltage, and thermal conditions across temperature because 275 mA describes the line-driver capability rather than unlimited continuous load capacity. This product record combines the manufacturer identification, package information, current capability, major ADSL and PLC use cases, and practical implementation considerations. It also provides sourcing guidance for the exact THS6093CD ordering code and distinguishes confirmed specifications from parameters that still require confirmation from the manufacturer datasheet.

RFQ संपर्क
THS6093CDR - 275mA +12V ADSL Line Driver | Texas Instruments (Tape & Reel)
THS6093CDR

THS6093CDR - 275mA +12V ADSL Line Driver | Texas Instruments (Tape & Reel)

The Texas Instruments THS6093CDR is a 275 mA, +12 V ADSL CPE and PLC line driver with shutdown, packaged in a 14-pin SOIC. It is designed for high-speed line-driving applications using either a 1:2 transformer ratio or single-supply operation. Its headline characteristics are 275 mA output current, +12 V supply operation, a 14-SOIC package, low 2.1 pA/√Hz noninverting current noise, and a shutdown function. An ADSL line driver is an interface integrated circuit that converts upstream data signals into suitable current and voltage levels for transmission over copper lines. It belongs to the interface IC hierarchy within integrated circuits and semiconductor signal-conditioning devices. The THS6093 is intended for full-rate ADSL and G.Lite equipment, including customer-premises equipment and power-line communication equipment where the line interface must combine high output current with controlled noise. Key features include compatibility with a 1:2 transformer ratio, a wide supply-voltage range, and suitability for single +12 V operation. The 275 mA output capability provides useful drive current for line termination and transformer coupling. The device also includes shutdown control, allowing a system to disable the driver when line transmission is not required. Low noninverting current noise of 2.1 pA/√Hz helps reduce noise coupled through a telephone hybrid into the downstream receiver path. The THS6093 uses a high-current output stage suited to the demanding load presented by an ADSL line interface. Its architecture supports both transformer-coupled and single-supply arrangements, giving designers flexibility in line-network topology. The 14-pin SOIC package is a conventional surface-mount format suitable for automated PCB assembly, although the high-current output path requires careful routing, thermal review, and adequate copper around the power and ground pins. Typical uses include ADSL CPE line interfaces, full-rate ADSL modems, G.Lite access equipment, PLC gateways, and communications terminals connected to copper lines. It is particularly relevant when the design needs a dedicated line driver with a shutdown control and operation from a +12 V supply rather than a general-purpose low-power amplifier. For PCB implementation, place the device close to the line-transformancer or network interface and keep the high-current output path compact. Use a low-inductance supply connection and adequate input and output bypassing according to the manufacturer application guidance. Verify maximum output current, voltage, and thermal conditions across temperature because 275 mA describes the line-driver capability rather than unlimited continuous load capacity. This product record combines the manufacturer identification, package information, current capability, major ADSL and PLC use cases, and practical implementation considerations. It also provides sourcing guidance for the exact THS6093CDR ordering code and distinguishes confirmed specifications from parameters that still require confirmation from the manufacturer datasheet.

RFQ संपर्क
THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments
THS6093ID

THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments

Texas Instruments THS6093ID is a dual-channel, high-speed ADSL CPE line driver rated for 275 mA output current and +12 V operation in a 14-pin SOIC package. The device is intended for driving signals from the remote terminal toward the central office in asymmetric digital subscriber line systems, including full-rate ADSL and G.Lite configurations. An ADSL line driver is a specialized interface-circuit component that converts upstream driver signals into robust, high-current line outputs suitable for copper telephone networks. It sits within the power-management and signal-conditioning hierarchy of a customer premises equipment design, translating logic-level commands into line-side waveforms while helping preserve signal integrity across the transformer-coupled network. Key features include a wide supply-voltage range, suitability for single +12 V operation, compatibility with a 1:2 transformer ratio, and low 2.1 pA/√Hz noninverting current noise. The THS6093 also provides low total harmonic distortion of -72 dBc while driving the line and includes shutdown control. Each channel draws only 7.3 mA of supply current, helping limit the power burden of a multi-output access circuit. The device uses two noninverting outputs in a 14-pin SOIC package. Its high output-current capability is important for ADSL line interfaces because the external transformer, network loading, and cable losses can require substantially more current than a conventional logic driver. The specified 275 mA rating provides the core design limit for transformer selection, copper-line loading, supply capability, and thermal analysis. Typical uses include full-rate ADSL customer premises equipment, G.Lite ADSL line interfaces, and power-line carrier line-driver circuits. In each application, the THS6093 can operate from a single +12 V rail and drive the line through an appropriate external transformer while the shutdown function provides a controlled path for reducing activity when the endpoint is inactive. The primary design consideration is ensuring that the +12 V supply, output-current demand, transformer ratio, load, thermal conditions, and signal-integrity expectations all agree. Use the manufacturer datasheet pin-description table when assigning PCB nets, and confirm that the selected transformer supports the specified 1:2 ratio and operating bandwidth.

RFQ संपर्क
THS6093IDR - 275mA +12V ADSL Line Driver | Texas Instruments (Tape & Reel)
THS6093IDR

THS6093IDR - 275mA +12V ADSL Line Driver | Texas Instruments (Tape & Reel)

Texas Instruments THS6093IDR is a dual-channel, high-speed ADSL CPE line driver rated for 275 mA output current and +12 V operation in a 14-pin SOIC package. The device is intended for driving signals from the remote terminal toward the central office in asymmetric digital subscriber line systems, including full-rate ADSL and G.Lite configurations. An ADSL line driver is a specialized interface-circuit component that converts upstream driver signals into robust, high-current line outputs suitable for copper telephone networks. It sits within the power-management and signal-conditioning hierarchy of a customer premises equipment design, translating logic-level commands into line-side waveforms while helping preserve signal integrity across the transformer-coupled network. Key features include a wide supply-voltage range, suitability for single +12 V operation, compatibility with a 1:2 transformer ratio, and low 2.1 pA/√Hz noninverting current noise. The THS6093 also provides low total harmonic distortion of -72 dBc while driving the line and includes shutdown control. Each channel draws only 7.3 mA of supply current, helping limit the power burden of a multi-output access circuit. The device uses two noninverting outputs in a 14-pin SOIC package. Its high output-current capability is important for ADSL line interfaces because the external transformer, network loading, and cable losses can require substantially more current than a conventional logic driver. The specified 275 mA rating provides the core design limit for transformer selection, copper-line loading, supply capability, and thermal analysis. Typical uses include full-rate ADSL customer premises equipment, G.Lite ADSL line interfaces, and power-line carrier line-driver circuits. In each application, the THS6093 can operate from a single +12 V rail and drive the line through an appropriate external transformer while the shutdown function provides a controlled path for reducing activity when the endpoint is inactive. The primary design consideration is ensuring that the +12 V supply, output-current demand, transformer ratio, load, thermal conditions, and signal-integrity expectations all agree. Use the manufacturer datasheet pin-description table when assigning PCB nets, and confirm that the selected transformer supports the specified 1:2 ratio and operating bandwidth.

RFQ संपर्क
THS6132VFP - High-Efficiency Class-G ADSL Driver | Texas Instruments
THS6132VFP

THS6132VFP - High-Efficiency Class-G ADSL Driver | Texas Instruments

The Texas Instruments THS6132VFP is a high-efficiency Class-G current-feedback differential line driver designed for full-rate ADSL DMT systems and PLC line-driver applications. The device combines a 2/0 differential driver configuration, low power consumption of 600 mW or less, and operation from a single 5 V supply in a 32-pin HLQFP package with an exposed thermal pad. Its differential architecture is intended for driving copper loops through transformer-coupled or balanced line interfaces while maintaining low signal distortion at high data rates. A line driver is an interface integrated circuit that converts a low-voltage differential logic signal into a larger-amplitude differential output capable of driving transmission-line impedance. Within the signal-chain hierarchy, the THS6132 belongs to the line-driver class of interface ICs, which sits above differential amplifiers and supports communication equipment such as DSL access concentrators, central-office line cards, and power-line communication gateways. Its Class-G operating architecture emphasizes high efficiency while reducing the quiescent current needed when the line is inactive. The principal advantages of the THS6132 are its low power dissipation, differential current-feedback output stage, and suitability for full-rate ADSL systems. The 32-pin HLQFP (VFP) package measures 7 x 7 mm and includes an exposed pad for improved thermal performance in dense communications equipment. The manufacturer identifies the device as a 2/0 driver, meaning it provides two differential outputs and no receiver inputs in the same package. Typical deployment is in ADSL line cards and central-office rack equipment where many line-driver channels must operate continuously within limited thermal and power budgets. The device can also serve PLC systems that use carrier-based communication over power lines, provided the external line interface, transformer coupling, protection network, and bandwidth requirements are designed for that environment. Differential routing helps reject common-mode noise picked up along externally routed copper pairs. When laying out a THS6132VFP circuit, treat the output stage and supply return as high-current paths even though the device is classified as a line driver. Keep the exposed-pad connection to the ground plane unobstructed, place supply bypass capacitors close to their pins, and follow the manufacturer pin-description table when assigning tracks. Decoupling values, differential termination, transformer turns ratio, and maximum line-reach parameters should be taken directly from the manufacturer datasheet rather than inferred from generic analog-design rules. This page combines the manufacturer device description with a practical view of package construction, thermal handling, interface topology, and application selection. It also organizes drop-in ordering variants, comparison parameters, and design cautions to support sourcing and first-pass PCB planning.

RFQ संपर्क
THS6182D - Low-Power ADSL/PLC Differential Driver | TI
THS6182D

THS6182D - Low-Power ADSL/PLC Differential Driver | TI

The Texas Instruments THS6182D is a low-power current-feedback differential line driver designed for full-rate ADSL and power-line communication systems. It delivers a 44 Vpp differential output swing, operates from dual supply rails, and is offered in a 16-pin SOIC package. The device includes selectable full, mid, low, and shutdown bias modes to balance output drive against power consumption. A line driver is an analog output interface that converts upstream signal information into a high-voltage differential signal capable of traversing copper, telephone, or other communications lines. The THS6182 belongs to the current-feedback operational-amplifier family and is positioned between a communications signal source and the physical line. Its differential architecture reduces susceptibility to common-mode noise while providing the voltage swing and current-drive capability needed by xDSL line cards. Key features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer identifies low distortion, low inverting current noise, and stable operation at low channel current as important benefits for receiver sensitivity and central-office line-card density. An IADJ pin also provides user-controlled bias current for system-level optimization. According to the manufacturer product page, the THS6182 is pin compatible with EL1503C and EL1508C line-driver families and is available in multiple packages and power-control modes. Its current-feedback differential architecture is intended to preserve signal integrity while minimizing dissipation, making it particularly relevant to high-density ADSL central-office equipment and PLC systems. The advertised 3.2 nV/√Hz inverting current noise supports receiver-sensitive signal paths. Typical deployments include full-rate ADSL central-office line cards, DSL access multiplexor equipment, remote terminal equipment, and PLC transmitters. In these systems, the driver accepts an upstream differential signal and produces a substantially larger differential output across the line interface. Designers must preserve the intended differential topology, provide suitable bypass capacitance, terminate unused inputs correctly, and verify thermal performance across the required line swing and channel-current range. A key design consideration is power mode selection. Full-bias mode provides maximum drive when required, while mid- and low-bias modes reduce dissipation when channel current and reach requirements permit. The shutdown state provides the lowest listed current, but enabling and disabling channels must be coordinated with the communication protocol to avoid invalid transmitted states. This page combines verified manufacturer and distributor information with application guidance; it does not infer unprovided electrical limits or invent replacement parts.

RFQ संपर्क
THS6182DR - Low-Power ADSL/PLC Differential Driver | TI (Tape & Reel)
THS6182DR

THS6182DR - Low-Power ADSL/PLC Differential Driver | TI (Tape & Reel)

The Texas Instruments THS6182DR is a low-power current-feedback differential line driver designed for full-rate ADSL and power-line communication systems. It delivers a 44 Vpp differential output swing, operates from dual supply rails, and is offered in a 16-pin SOIC package. The device includes selectable full, mid, low, and shutdown bias modes to balance output drive against power consumption. A line driver is an analog output interface that converts upstream signal information into a high-voltage differential signal capable of traversing copper, telephone, or other communications lines. The THS6182 belongs to the current-feedback operational-amplifier family and is positioned between a communications signal source and the physical line. Its differential architecture reduces susceptibility to common-mode noise while providing the voltage swing and current-drive capability needed by xDSL line cards. Key features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer identifies low distortion, low inverting current noise, and stable operation at low channel current as important benefits for receiver sensitivity and central-office line-card density. An IADJ pin also provides user-controlled bias current for system-level optimization. According to the manufacturer product page, the THS6182 is pin compatible with EL1503C and EL1508C line-driver families and is available in multiple packages and power-control modes. Its current-feedback differential architecture is intended to preserve signal integrity while minimizing dissipation, making it particularly relevant to high-density ADSL central-office equipment and PLC systems. The advertised 3.2 nV/√Hz inverting current noise supports receiver-sensitive signal paths. Typical deployments include full-rate ADSL central-office line cards, DSL access multiplexor equipment, remote terminal equipment, and PLC transmitters. In these systems, the driver accepts an upstream differential signal and produces a substantially larger differential output across the line interface. Designers must preserve the intended differential topology, provide suitable bypass capacitance, terminate unused inputs correctly, and verify thermal performance across the required line swing and channel-current range. A key design consideration is power mode selection. Full-bias mode provides maximum drive when required, while mid- and low-bias modes reduce dissipation when channel current and reach requirements permit. The shutdown state provides the lowest listed current, but enabling and disabling channels must be coordinated with the communication protocol to avoid invalid transmitted states. This page combines verified manufacturer and distributor information with application guidance; it does not infer unprovided electrical limits or invent replacement parts.

RFQ संपर्क
THS6182DW - Low-Power ADSL/PLC Line Driver | Texas Instruments
THS6182DW

THS6182DW - Low-Power ADSL/PLC Line Driver | Texas Instruments

The Texas Instruments THS6182DW is a low-power differential line driver designed for full-rate ADSL and power-line communication systems, with a 20-pin SOIC package. It uses current-feedback architecture, provides selectable operating-current modes, and supports an adjustable bias-current input. The device is specified for 1/0 DSL line-driving duties over a temperature range of -40°C to +85°C. An ADSL line driver is a specialized interface-circuit component that converts upstream data into a high-current differential signal suitable for transmission over copper telephone lines. This device belongs to the interface IC hierarchy: line driver → differential transceiver → communications interface → semiconductor. Unlike a general-purpose voltage-output amplifier, a current-feedback line driver combines high-frequency signal capability with output-current control designed specifically for line networks. Key operating features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer also identifies operation down to 1.8 mA per channel, an adjustable-current input, and a low-noise result of 3.2 nV/√Hz inverting current noise. These selectable modes allow designers to balance transmission performance against power dissipation. The current-feedback differential architecture supports full-rate ADSL applications while maintaining high linearity without the complexity and power burden of conventional designs. The adjustable bias input lets the circuit user control the operating-current condition, making it useful in designs where line length, transformer characteristics, aggregate line load, or central-office power density affect the preferred drive level. The THS6182 is also identified as pin-compatible with the EL1503C and EL1508C. Typical uses include ADSL central-office line-card equipment, DSL access concentrators, splitters, remote-terminal and line-unit equipment, and PLC interface circuits. The device is particularly relevant where multiple line channels share a constrained power budget, because its low-bias and shutdown modes reduce dissipation when channel activity is low or a port must be disabled. The primary design trade-off is current setting versus signal performance and power consumption. Select full-bias operation for maximum line drive, lower modes for reduced dissipation, and shutdown when the port is inactive. Place the device and its associated line-network components carefully because long high-current transmission paths can introduce impedance discontinuities and signal-integrity problems that are not corrected by changing bias mode. This product page combines the manufacturer’s functional description, operating-mode data, package information, interface use cases, and replacement guidance with practical selection notes. It also highlights the distinction between electrically equivalent order codes and genuinely pin-compatible drop-in choices, helping engineers assess whether a redesign or package-level substitution is actually required.

RFQ संपर्क
THS6182DWR - Low-Power ADSL/PLC Line Driver | Texas Instruments (Tape & Reel)
THS6182DWR

THS6182DWR - Low-Power ADSL/PLC Line Driver | Texas Instruments (Tape & Reel)

The Texas Instruments THS6182DWR is a low-power differential line driver designed for full-rate ADSL and power-line communication systems, with a 20-pin SOIC package. It uses current-feedback architecture, provides selectable operating-current modes, and supports an adjustable bias-current input. The device is specified for 1/0 DSL line-driving duties over a temperature range of -40°C to +85°C. An ADSL line driver is a specialized interface-circuit component that converts upstream data into a high-current differential signal suitable for transmission over copper telephone lines. This device belongs to the interface IC hierarchy: line driver → differential transceiver → communications interface → semiconductor. Unlike a general-purpose voltage-output amplifier, a current-feedback line driver combines high-frequency signal capability with output-current control designed specifically for line networks. Key operating features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer also identifies operation down to 1.8 mA per channel, an adjustable-current input, and a low-noise result of 3.2 nV/√Hz inverting current noise. These selectable modes allow designers to balance transmission performance against power dissipation. The current-feedback differential architecture supports full-rate ADSL applications while maintaining high linearity without the complexity and power burden of conventional designs. The adjustable bias input lets the circuit user control the operating-current condition, making it useful in designs where line length, transformer characteristics, aggregate line load, or central-office power density affect the preferred drive level. The THS6182 is also identified as pin-compatible with the EL1503C and EL1508C. Typical uses include ADSL central-office line-card equipment, DSL access concentrators, splitters, remote-terminal and line-unit equipment, and PLC interface circuits. The device is particularly relevant where multiple line channels share a constrained power budget, because its low-bias and shutdown modes reduce dissipation when channel activity is low or a port must be disabled. The primary design trade-off is current setting versus signal performance and power consumption. Select full-bias operation for maximum line drive, lower modes for reduced dissipation, and shutdown when the port is inactive. Place the device and its associated line-network components carefully because long high-current transmission paths can introduce impedance discontinuities and signal-integrity problems that are not corrected by changing bias mode. This product page combines the manufacturer’s functional description, operating-mode data, package information, interface use cases, and replacement guidance with practical selection notes. It also highlights the distinction between electrically equivalent order codes and genuinely pin-compatible drop-in choices, helping engineers assess whether a redesign or package-level substitution is actually required.

RFQ संपर्क
THS6182PWP - Low-Power ADSL Line Driver | Texas Instruments
THS6182PWP

THS6182PWP - Low-Power ADSL Line Driver | Texas Instruments

The Texas Instruments THS6182PWP is a low-power differential ADSL and power-line communications line driver with one transmitter, operating from a 5 V to 15 V supply in a 20-pin HTSSOP package with an exposed pad. It provides four selectable bias modes, low total harmonic distortion of -88 dBc at 100 kHz and 1 MHz, and can drive the line at +20 dBm while maintaining -76 dBc distortion with the high-bias setting. An ADSL line driver is an interface IC that converts a low-amplitude differential source signal into a high-current differential output suitable for transmission over telephone-line copper. This device belongs to the broader line-driver and transmitter hierarchy, within interface ICs and communication semiconductors. Its architecture is designed to increase line-card density by reducing quiescent current and power dissipation while maintaining the linearity required for full-rate ADSL systems. The THS6182PWP supports full-bias, mid-bias, low-bias, and shutdown operating modes. The advertised channel-current settings are 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. An ADJ pin allows user-controlled bias current, and operation remains stable down to 1.8 mA per channel. Signal-chain performance is centered on low distortion and low noise. The manufacturer lists total harmonic distortion of -88 dBc at 100 kHz and 1 MHz, while the high-bias configuration can drive +20 dBm on the line with -76 dBc distortion. The input current-noise density is listed as 3.2 nV per square hertz. These characteristics are relevant to receiver sensitivity because distortion and noise introduced at the line-driver stage can reduce the usable margin of the downstream receiver. Typical applications include full-rate ADSL line cards, central-office ADSL equipment, power-line communication transmitters, and other copper-pair interfaces requiring differential current-drive capability. The adjustable bias architecture supports different line lengths, launch-power requirements, and system power budgets. A high-bias setting provides greater drive level when line loss is severe, while the lower-current modes reduce dissipation where adequate reach or signal level is not required. PCB implementation requires attention to the exposed thermal pad, supply decoupling, high-current return paths, and controlled-impedance differential routing. Keep the driver close to the transformer or line-coupling network, minimize loop area in output-current paths, and use the manufacturer-recommended power and ground-plane construction to limit parasitic inductance. The exposed pad must be connected to the ground plane for both electrical return and heat dissipation. This page consolidates the manufacturer specifications, package details, application guidance, and verified cross-reference information for engineers evaluating the THS6182PWP. It also identifies why a mechanically and electrically identical replacement should not be assumed from a similar line-driver description. Use the Texas Instruments THS6182 datasheet for the final pin assignments, recommended application circuit, exposed-pad layout, and electrical characteristics before releasing a PCB.

RFQ संपर्क
THS6184PWP - Dual-Port Low-Power xDSL Line Driver | TI
THS6184PWP

THS6184PWP - Dual-Port Low-Power xDSL Line Driver | TI

The Texas Instruments THS6184PWP is a dual-port, low-power differential xDSL line-driver amplifier system with four current-feedback amplifiers, a 4 V to 32 V supply range, and a 20-pin exposed-pad HTSSOP package. Its low-bias mode consumes 4.2 mA per port while maintaining -83 dBc total harmonic distortion at 1 MHz. An xDSL line-driver amplifier is the output stage used to drive copper telephone lines with large signal amplitudes, controlled differential voltage, and low distortion. The THS6184 combines two independent differential driver ports in one package, allowing one IC to implement four amplifiers. This integration reduces board area in ADSL, ADSL2, ADSL2+, and ADSL2++ line-card equipment while supporting the low power consumption required by high-density central-office installations. The THS6184 architecture provides trimmed, selectable bias modes for different line lengths and operating conditions. These operating modes let a designer trade power consumption against drive performance instead of applying one fixed bias level to every subscriber line. Low-bias operation is particularly useful where shorter lines, lower signal amplitudes, or system power limits make maximum drive unnecessary. The device also supports both fixed and variable multiple-bias configurations for flexible line-card design. Signal-chain performance is centered on current-feedback amplification and the device's low-power operating architecture. According to the Texas Instruments THS6184 datasheet, low-bias mode delivers -83 dBc THD at 1 MHz with 4.2 mA per port. This combination indicates that the driver can preserve waveform linearity while controlling dissipation. The exposed thermal pad beneath the HTSSOP package provides a direct heat-spreading path to the PCB, which is important when several driver ports operate continuously in a dense line card. Typical deployments include ADSL and ADSL2+ subscriber-line-access equipment, central-office line cards, voice-over-DSL access nodes, and other high-density copper-access systems. Two ports per package support compact designs with four differential amplifier channels, while the low-power architecture addresses the thermal and system-level energy constraints of telecom central offices. Care must be taken to terminate unused channels and configure bias, supply decoupling, and exposed-pad grounding according to the manufacturer layout guidance. PCB design should provide a continuous ground plane and adequate copper area beneath the exposed pad. Input and output return paths should be short and appropriately terminated to minimize parasitic feedback and preserve differential signal integrity. The power supply must remain within the 4 V to 32 V operating range, and thermal performance should be checked at the highest expected line amplitude, bias mode, ambient temperature, and port-loading condition. This page combines device functionality, operating-mode guidance, package details, and practical design considerations for engineers evaluating the THS6184PWP for xDSL line-card designs.

RFQ संपर्क
THS6212YS - Broadband PLC Line Driver | Texas Instruments
THS6212YS

THS6212YS - Broadband PLC Line Driver | Texas Instruments

Texas Instruments THS6212YS is a high-speed, differential broadband PLC/HPLC line-driver amplifier based on current-feedback architecture, with support for line power up to 14.5 dBm at frequencies through 30 MHz. The device is supplied in a 17-terminal, rectangular, no-lead die package. Its differential output topology is intended for power-line communication systems that require broadband signal transmission through challenging in-home or outdoor network wiring. A broadband PLC line driver is an interface amplifier that generates a differential signal for transmission over power-line communication wiring. The THS6212 belongs to the line-driver and receiver hierarchy of interface ICs, where its current-feedback amplifier architecture provides the active gain stage needed to drive external circuitry and realize a physical-layer transmitter signal. This makes it relevant to broadband PLC modems, HPLC endpoints, carrier communication equipment, and line-coupling networks. The manufacturer identifies current-feedback architecture, differential operation, transmission capability through 30 MHz, and line power up to 14.5 dBm as the principal characteristics of the THS6212. Differential drive helps reject common-mode disturbances picked up from the shared power-line environment. The broad operating bandwidth supports both low-frequency carrier data and substantially higher-frequency communication signals, while the 28 V maximum supply rating provides headroom for an industrial interface stage. The target is identified as an industrial-temperature device operating from -40 °C to +85 °C. Its 17-terminal no-lead package is intended for surface-mount assembly. Because this ordering code is associated with a die rather than a conventional leaded or molded IC package, PCB land-pattern design, exposed-pad treatment, assembly profile, and reflow requirements must be confirmed against the official package drawing before layout release. Typical uses include broadband PLC transmitters, HPLC communication endpoints, carrier-current networking equipment, and line-driver stages for communications over existing electrical infrastructure. In a transmitter implementation, the amplifier output is connected through the appropriate line-coupling and filtering network. Component values and protection requirements depend on the transformer, line impedance, conducted-emissions target, and safety arrangement of the complete communication equipment. Design should preserve the high-speed current-feedback path with short traces, carefully controlled return current, and decoupling placed close to the supply pins. Output isolation, impedance matching, and surge protection must be evaluated together because a line driver also sees the external network's distributed and transient behavior. The amplifier rating does not remove the need for application-level isolation and protection. This page consolidates the manufacturer's device description, electrical and environmental limits, sourcing structure, and engineering guidance. It also distinguishes verified device facts from parameters that require the official datasheet or package drawing, helping designers establish whether the THS6212YS fits a broadband PLC signal chain before committing the layout.

RFQ संपर्क
THS7303PW - 3-Channel Low-Power Video Amplifier | TI
THS7303PW

THS7303PW - 3-Channel Low-Power Video Amplifier | TI

The Texas Instruments THS7303PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 6 dB gain, SAG correction, a 2:1 input multiplexer, and selectable input bias modes. It operates from a single 2.7 V to 5 V supply and is packaged in a 20-pin TSSOP (PW). The device also features a 190 MHz bandwidth and a 320 V/µs slew rate, making it suited to high-speed video signal processing. A video amplifier is an analog signal-conditioning IC that increases the amplitude and drive capability of composite, component, or other video signals. It belongs to the broader hierarchy of amplifier ICs, analog integrated circuits, and signal-chain semiconductors. The THS7303PW combines three buffered video channels with programmable control, allowing a compact design to select filtering, gain, multiplexer routing, and bias behavior without replacing multiple fixed-function devices. Its principal features include three integrated video amplifiers, a 2:1 input multiplexer, a selectable 6 dB gain setting, selectable low-pass filters, SAG correction, and an I2C interface. These functions support programmable video paths in set-top boxes, video processors, display equipment, surveillance systems, and general-purpose analog-to-digital signal-processing circuits. Low power consumption is particularly useful when three active video channels must operate continuously in compact commercial or industrial equipment. The THS7303PW uses a complementary silicon-germanium BiCom-III process according to the manufacturer documentation. Its approximately 190 MHz small-signal bandwidth and 320 V/µs slew rate provide ample speed for high-frequency video signals. The 2.1:1 power-supply current and 6 mA quiescent current reported in the device documentation describe a low-power design intended to balance drive strength, integration, and heat management in a surface-mount package. Typical uses include conditioning composite video for digitization, buffering multiple video outputs, switching between two input sources with a 2:1 multiplexer, and applying programmable filter or gain settings in display and broadcast equipment. The I2C control interface also enables software-controlled configuration of multiple channels in systems where the video path changes during operation. PCB design should preserve the short, controlled return paths needed by high-speed analog signals. Place input and output bypass capacitors close to the relevant supply and ground pins, keep video traces away from switching nodes and digital control lines, and follow the pin descriptions and layout guidance in the manufacturer datasheet. Bus pull-up resistors and series damping should be selected to keep SCL and SDA waveforms within valid limits. This page organizes the THS7303PW’s functions, pin-compatible replacement information, comparison parameters, application guidance, and practical design considerations. It supports faster component evaluation by placing the device’s key architectural features alongside the engineering checks required for reliable video-signal implementation.

RFQ संपर्क
THS7313PW - 3-Channel 6dB SDTV Video Amp | Texas Instruments
THS7313PW

THS7313PW - 3-Channel 6dB SDTV Video Amp | Texas Instruments

The Texas Instruments THS7313PW is a three-channel, low-power SDTV video amplifier with I2C control, selectable 6 dB gain, sag correction, 2:1 input multiplexing, and selectable input-bias modes. The device operates from a single 2.7 V to 5 V supply and is packaged in a 20-pin TSSOP (PW) package. It combines three video processing channels with digital configuration in one low-power integrated circuit. A video amplifier conditions analog composite video signals by providing gain, impedance buffering, bias control, and correction functions before the signal reaches an encoder, display interface, or video capture stage. The THS7313 belongs to the video-amplifier hierarchy within interface ICs and is intended for SDTV and related composite-video signal paths requiring controlled amplitude and multiple source selection. The principal features are three integrated video channels, 6 dB gain, 2:1 input multiplexing, sag correction, I2C-controlled configuration, and selectable input-bias modes. The 2:1 multiplexer allows each channel to select between two video inputs, reducing the number of external routing components when the source changes infrequently. I2C control supports programmable configuration while avoiding dedicated control pins for every parameter. The device is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of high-speed analog video functions, low-power operation, and digital control in one monolithic device. Single-supply operation also simplifies PCB power planning in portable and space-constrained consumer equipment. Typical uses include SDTV set-top boxes, video scalers, digital video recorders, television sets, video game consoles, and other systems that process composite video. The three-channel architecture suits designs carrying red, green, and blue component signals or three separate composite-video channels. The integrated multiplexer is especially useful when each channel must accept one of two source signals. Designers should preserve the recommended input and output network, provide a stable low-noise supply, and verify I2C address and configuration settings before enabling signal routing. Because no complete pin-description table is reproduced here, use the manufacturer datasheet pin table and typical-application circuit when assigning tracks, terminating inputs, and placing bypass capacitors. This page consolidates the device identity, package information, verified commercial listing, candidate drop-in relationships, application guidance, and engineering considerations into a practical reference for evaluating the THS7313PW.

RFQ संपर्क
THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7314D

THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments

The Texas Instruments THS7314D is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314D provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314D and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

RFQ संपर्क
THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7314DR

THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments THS7314DR is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314DR provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314DR and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

RFQ संपर्क
THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7315D

THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments

Texas Instruments THS7315D is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315D is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315D integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315D characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315D in SDTV video signal chains.

RFQ संपर्क
THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7315DR

THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7315DR is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315DR is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315DR integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315DR characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315DR in SDTV video signal chains.

RFQ संपर्क
THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments
THS7316D

THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments

Texas Instruments THS7316D is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316D are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316D. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

RFQ संपर्क
THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7316DR

THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7316DR is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316DR are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316DR. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

RFQ संपर्क
THS7353PW - 3-Channel I2C Video Amp | Texas Instruments
THS7353PW

THS7353PW - 3-Channel I2C Video Amp | Texas Instruments

Texas Instruments THS7353PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 0 dB gain, and a 2:1 input multiplexer in a 20-pin TSSOP (PW) package. It operates from a single 2.7 V to 5 V supply and consumes 16.2 mA total quiescent current at a 3.3 V supply. A video amplifier, also called a video buffer, conditions analog video signals between source and destination stages. The THS7353 belongs to the broader integrated video-amplifier hierarchy, combining signal buffering, gain control, filtering, input selection, and serial configuration in one semiconductor. This integration reduces the number of discrete signal-path components while allowing programmable behavior through an I2C interface. The device provides three video channels, a selectable 2:1 multiplexer, selectable low-pass or bypass filter configurations, and programmable 0 dB gain. Its low-power design and single-supply operation suit portable equipment, including USB-powered systems, as well as HDTV, PVR, DVDR, projector, and general-purpose video equipment. An operating-temperature range of -40 °C to +85 °C supports industrial and commercial environments. The THS7353 is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of three video channels, filtering functions, multiplexing, gain control, and digital control into a compact low-power device. The 20-TSSOP package supports surface-mount PCB assembly while providing separate routing flexibility for three video channels. Typical deployments include buffering component video and computer video outputs, switching between two video sources through the 2:1 multiplexer, filtering unwanted video-frequency content, and protecting source devices from downstream loading. Portable and projector designs benefit from the 2.7 V minimum supply and 16.2 mA quiescent current at 3.3 V, although system-level power depends on the selected configuration and output loading. Design the I2C address and control register settings before laying out the PCB, and confirm compatibility with the video timing and filter requirements of the target source. Decoupling and analog return paths should be arranged to minimize switching noise and ground potential differences between the amplifier and video source. This product page combines manufacturer specifications, application guidance, candidate replacement analysis, and practical PCB considerations. It identifies where THS7353PW fits, which published alternatives remain unverified as true pin-to-pin replacements, and which design parameters should be checked before approving a substitution.

RFQ संपर्क
THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments
THS7375

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

The THS7375 is a low-power, single-supply, 3 V to 5 V four-channel integrated video buffer from Texas Instruments, fabricated using the complementary Silicon-Germanium (SiGe) BiCom3X process. It is available in a lead-free and green (RoHS) compliant TSSOP-14 package. The device incorporates a sixth-order Butterworth filter that can be bypassed, making it useful as a digital-to-analog converter (DAC) reconstruction filter. With a rail-to-rail output stage and a fixed gain of 5.6 V/V (15 dB), the THS7375 is designed for SDTV video applications, providing excellent image quality and driving capability for both AC and DC coupled loads. A video amplifier is an electronic amplifier that processes video signals, typically providing gain, buffering, and filtering to ensure signal integrity over transmission lines. In the signal chain, the THS7375 sits between a video DAC or encoder and the output connector, performing reconstruction filtering and line driving. It belongs to the category of integrated video buffers, which are essential in consumer electronics, set-top boxes, DVD players, and video surveillance systems. The THS7375's integrated filters eliminate the need for external passive components, simplifying design and reducing board space. Key features include a 6th-order Butterworth filter with a cutoff frequency suitable for SDTV (standard-definition television) signals, a fixed gain of 5.6 V/V, and the ability to drive two lines per channel or 75-ohm loads. The device operates from a single 3 V to 5 V supply, making it compatible with common digital logic levels. The rail-to-rail output stage ensures maximum output swing, and the low power consumption makes it ideal for battery-powered or power-sensitive applications. Technically, the THS7375 uses the BiCom3X process, which combines bipolar and CMOS transistors on a silicon-germanium substrate, offering high-speed performance with low power. The integrated filter is a 6th-order Butterworth type, providing a flat passband and sharp roll-off to remove out-of-band noise and aliasing artifacts. The device also features an internal gain of 5.6 V/V, which is optimized for driving video loads with proper termination. Typical applications include video buffer and line driver for SDTV signals in set-top boxes, DVD players, video recorders, and surveillance systems. It is also suitable for driving video signals from DaVinci processors and other video encoders. The THS7375's ability to drive two lines per channel allows for flexible routing in complex video distribution systems. When designing with the THS7375, ensure proper power supply decoupling with a 0.1 uF ceramic capacitor close to the VCC pin. The input should be AC-coupled if the source has a DC offset, and the output should be terminated with 75-ohm resistors to match the characteristic impedance of the cable. The filter bypass pin can be used to disable the internal filter if external filtering is preferred.

RFQ संपर्क
THS7530PWP - 300 MHz Fully Differential VGA | Texas Instruments
THS7530PWP

THS7530PWP - 300 MHz Fully Differential VGA | Texas Instruments

The Texas Instruments THS7530PWP is a fully differential, continuously variable gain amplifier featuring a 300 MHz bandwidth, DC-coupled operation, and a 14-pin HTSSOP package with an exposed thermal pad. It accepts a single-ended or differential supply and combines high-impedance differential inputs, low-impedance differential outputs, voltage-controlled gain, output common-mode control, and output voltage clamping. A variable gain amplifier, or VGA, is an amplifier whose gain changes under electronic control. A VGA belongs to the broader family of amplifiers, which in turn forms part of the analog and mixed-signal semiconductor hierarchy. Unlike a fixed-gain amplifier, a VGA allows a receiver, imaging system, or instrumentation channel to vary signal amplitude without changing the surrounding circuit topology. The fully differential architecture preserves a balanced signal path and reduces sensitivity to common-mode disturbances. Key features include a 300 MHz small-signal bandwidth, voltage-controlled continuous gain adjustment, differential input and differential output operation, and separate control of output common mode. The device operates from a single 5.5 V supply or from split supplies of ±2.75 V. Its 14-pin HTSSOP package exposes a thermal pad for improved heat dissipation, and the specified operating temperature range is -40 °C to 85 °C. Internally, the THS7530 uses Texas Instruments' BiCom III silicon-germanium complementary bipolar process. That process supports the high-speed operation required by the device while preserving DC coupling and low-impedance differential outputs. The gain-control and common-mode inputs are high-bandwidth control paths, so their routing and impedance matter as much as the signal inputs when system settling time is important. Typical uses include ultrasound and medical imaging front ends, communications receivers, instrumentation amplifiers, oscilloscope and test-equipment input chains, and other wideband analog systems that require adjustable attenuation or gain. Differential signaling is particularly useful when the source produces a small differential voltage across a common-mode range that a single-ended amplifier would not accommodate cleanly. For PCB design, use the exposed thermal pad as a heat-spreading and low-inductance connection rather than leaving it electrically unconnected. Place input, output, gain-control, and common-mode routing away from high-current switching nodes. Terminate differential pairs symmetrically and follow the pin-description table in the manufacturer datasheet when assigning tracks and ground connections. This page combines the manufacturer device information, orderable-package details, practical PCB guidance, and a constrained drop-in comparison for engineers who need a 300 MHz fully differential VGA in the HTSSOP PWP footprint. Use the Request a Quote form on this page for current commercial availability, minimum order quantity, and lead-time confirmation.

RFQ संपर्क
THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments
THS788PFD

THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments

The Texas Instruments THS788PFD is a four-channel time measurement unit (TMU) using time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from an external 200 MHz controller clock, and a measurement result range of 7 s in a 100-pin HTQFP package. It supports a 200 MHz event-input rate and provides LVDS-compatible event inputs, an LVDS result interface, four event channels, and a synchronization channel. A time measurement unit is a specialized clock-and-timing semiconductor that converts the elapsed time between events into a digital result. The THS788 belongs to the TMU hierarchy, where its TDC architecture combines fine timing resolution with high-rate event capture. This makes it suitable for systems requiring precise timing rather than ordinary counting, including synchronized instrumentation, pulsed systems, test equipment, and communications or industrial timing subsystems. The key performance feature is 8 ps single-shot accuracy, supported by a 13 ps least-significant-bit resolution. The external controller clock operates at 200 MHz, and the event input rate can reach 200 MHz. The 7 s result range supports substantially longer measurement intervals than the 13 ps conversion resolution alone would imply, depending on the configured measurement sequence and system implementation. LVDS-compatible interfaces provide high-speed, noise-resistant signaling for demanding board environments. Technically, the THS788 uses a fast TDC architecture to perform time measurements across four event channels. Its inputs are designed for LVCMOS or LVDS signaling, while the result output is identified as LVDS. The synchronized architecture and dedicated sync channel make the device suitable for multi-event acquisition where repeatable timing relationships matter. The stated low temperature coefficient of 0.1 ps/°C indicates attention to timing stability over temperature. Typical applications include high-speed test and measurement systems, pulsed-signal analysis, synchronization of multiple timing events, industrial automation requiring deterministic event capture, and communications equipment that must measure narrow time intervals. The device can also support scientific instrumentation where event timing accuracy directly affects the quality of the collected result. Designers should treat the external 200 MHz clock, LVDS-compatible input routing, result interface, decoupling, and high-speed return paths as an integrated signal-integrity problem. Input timing, trace length, termination, and controller configuration must be evaluated together because the 13 ps resolution does not guarantee end-to-end system accuracy without clean clocking, controlled stimulus, and correct interface implementation. This page combines the verified manufacturer and distributor information for the THS788PFD with practical selection guidance, application analysis, pricing references, and an honest assessment of available drop-in alternatives.

RFQ संपर्क