उत्पाद (46,000+)

THS788PFDT - 200MHz 4-Channel 8ps Timing IC | Texas Instruments
THS788PFDT

THS788PFDT - 200MHz 4-Channel 8ps Timing IC | Texas Instruments

The Texas Instruments THS788PFDT is a four-channel time measurement unit (TMU) built around a time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from a 200 MHz external controller clock, and fast LVDS-compatible event inputs. The device is packaged in a 100-terminal 14 x 14 mm HTQFP surface-mount package and is intended for precision time-interval measurement applications. A time measurement unit is a specialized timing IC that converts the arrival time of an event into a digital value relative to a synchronization reference. The THS788 places a time-to-digital converter inside each measurement channel, allowing timing information to be captured with picosecond-class resolution instead of relying on a general-purpose counter clock. Its hierarchy runs from time measurement unit to time-to-digital converter, then to application-specific clock and timing IC and semiconductor. Key features include four measurement channels, 8 ps single-shot accuracy, 13 ps time-to-digital-converter resolution, and LVDS-compatible event inputs. The 200 MHz master clock determines the nominal TDC timing resolution, while a sync-channel input establishes time zero. According to the manufacturer product page, the device uses fast LVDS-compatible interfaces for its event inputs and supports calibrated timing calculations relative to the synchronization reference. The device supports fast event capture through hit latches, which latch an event edge before the timing data is processed. This architecture is useful when several channels must respond to closely spaced signals and the relative delay between them must be measured reliably. The controller interface and external clock remain essential parts of the measurement system because synchronization, calibration, and digital result transfer determine the integrity of the captured timing data. Typical applications include pulsed-laser range measurement, optical communication timing, radar and test instrumentation, high-speed trigger correlation, and industrial diagnostics that compare an event against a periodic reference. In such systems, the sync channel defines time zero, each event input records its relative arrival time, and the external controller applies calibration values before reporting the result. A critical design consideration is preserving the integrity of the 200 MHz reference clock and the LVDS-compatible event signals. Route timing-sensitive inputs as controlled-impedance nets, keep the clock away from high-current switching nodes, and use the exposed-pad land pattern and thermal vias recommended in the package drawing. Differential timing measurements are only as accurate as the reference distribution and input return-loss behavior of the complete board. This page consolidates the manufacturer timing specifications, package details, sourcing channels, and engineering guidance for the THS788PFDT, adding pin-connection and thermal-placement guidance that engineers would otherwise have to derive across multiple technical documents.

RFQ संपर्क
THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI
THS789PFD

THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI

Texas Instruments THS789PFD is a quad-channel time measurement unit (TMU) with a 200 MHz measurement clock, one output, and a 100-pin HTQFP package measuring 14 mm by 14 mm. The device is listed for commercial-grade operation from 0 °C to 70 °C and is supplied in a tray. Its verified product identity also includes an exposed thermal pad and surface-mount construction. A time measurement unit is a specialized clock-and-timing semiconductor that measures elapsed time by comparing reference events. A multi-channel TMU extends this function across several independent measurement paths, making it useful when a system must acquire timing relationships, delays, pulse widths, or event intervals without implementing each measurement function as discrete logic. The THS789 therefore belongs to the clock-and-timing IC category and the broader application-specific timing semiconductor hierarchy. The principal verified specifications are four measurement channels, a 200 MHz timing reference, and one output. The 200 MHz reference corresponds to a 5 ns reference period, while the quad-channel architecture permits parallel timing observations. The 100-pin HTQFP package provides numerous external connections for timing inputs, control, power, and outputs, while the exposed pad supports heat transfer from the device to the PCB. The THS789PFD is specifically identified as a Time Measurement IC and is marketed by DigiKey under the Application Specific Clock/Timing classification. This distinguishes it from conventional general-purpose timers by emphasizing precision event-interval measurement across four channels. The exact input voltage range, minimum measurable interval, timing accuracy, propagation delay, output characteristics, and power specifications are not included in the supplied verified excerpts and should be taken from the complete manufacturer datasheet before design release. Typical engineering uses include industrial automation equipment, communications timing analysis, instrumentation, automated test systems, and embedded systems that compare multiple event arrivals. The 100-pin package and exposed pad make careful PCB layout, grounding, and thermal management important. In multi-channel systems, signal integrity at the timing inputs can materially affect measurement consistency, so controlled impedance, short return paths, and clean reference distribution should be prioritized. A principal design trade-off is package size versus channel density: the 14 mm by 14 mm HTQFP offers extensive connectivity for four timing channels but requires more PCB area than a compact mixed-signal package. Engineers should also confirm the complete electrical limits and interface timing before substituting another device or extending the operating temperature beyond the verified 0 °C to 70 °C range. This product record combines verified manufacturer and distributor identity, package and ordering information, commercial availability, and explicit engineering guidance for evaluating the THS789PFD. It also distinguishes confirmed facts from parameters that still require review in the full Texas Instruments datasheet, supporting faster procurement and design planning without treating unverified specifications as guaranteed.

RFQ संपर्क
THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI
THS8135PHP

THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI

The Texas Instruments THS8135PHP is a triple 10-bit video digital-to-analog converter optimized for video and graphics applications, with a maximum sampling rate of 240 MSPS in a 48-lead HTQFP package measuring 7 mm by 7 mm. It operates from a 3.3 V analog supply and a 1.8 V digital supply, separating sensitive analog signaling from lower-voltage digital control and data inputs. A DAC is a data converter that translates digital codes into proportional analog voltages or currents. Video DACs belong to the broader ADC/DAC and data-converter IC hierarchy, where they sit between parallel digital pixel data and analog signals used by display or video-processing circuitry. The THS8135PHP combines three converters with circuitry for bi-level or tri-level synchronization and blanking-level generation. The principal features of this device are its three independent 10-bit conversion channels, 240 MSPS performance, parallel digital interface, and dedicated analog and digital supply rails. Each converter resolves the video signal into 10-bit steps. The parallel interface supports direct connection to video data sources without requiring a serial interface or a separate high-speed communication protocol. The package also provides a consolidated implementation for three color channels rather than requiring three separate DAC packages. The architecture is tailored to conventional component and graphics video systems. ITU-R BT.601-compatible full-scale output is identified for this device, making its output scaling suitable for standard-definition digital-video workflows. Bi-level and tri-level sync generation can produce the blanking levels required when converting active digital video into analog composite video. The 3.3 V analog rail and 1.8 V digital rail support partitioned supply planning, although both rails and the interface still require careful decoupling. Typical applications include SD and other video graphics systems, test and measurement video generation, digital signage, display-processing boards, and industrial imaging panels. The device is particularly useful when three synchronized analog outputs are required and the source interface already provides parallel pixel data. Its 240 MSPS ceiling provides substantial timing margin for common progressive video rates. PCB design should keep analog and digital return currents separated, place supply capacitors close to their corresponding pins, and route the parallel data bus with matched-length practices where timing margin is limited. The 48-lead HTQFP also requires careful thermal design because sustained high update rates can increase package dissipation. Use the manufacturer's pin-description table when assigning every power, data, clock, sync, and output connection. This page combines the device's principal conversion specifications, application guidance, package details, and engineering-focused replacement considerations. It also organizes sourcing information and drop-in comparison points into a format intended to accelerate schematic review, footprint verification, and prototype planning.

RFQ संपर्क
THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments
THS8136PHP

THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments

The Texas Instruments THS8136PHP is a triple 10-bit, 180-MSPS graphics and video digital-to-analog converter in a 48-pin HTQFP package measuring 7 mm by 7 mm. It operates from a 3.3 V analog supply and a 1.8 V digital supply, integrating three parallel-input DAC channels with circuitry for bi-level sync and blanking-level generation. The converter is designed for video and graphics systems that require simultaneous red, green, and blue analog outputs. A DAC is a data converter that translates digital color or graphics codes into proportional analog voltages. The THS8136 belongs to the video DAC category, a specialized form of digital-to-analog converter used to drive analog display and video-processing equipment. Its parallel interface, triple-channel architecture, and integrated sync and blanking support place it within high-speed video signal-chain components rather than general-purpose precision DACs. The device provides three 10-bit DAC channels operating at sampling rates up to 180 MHz. Its 1.8 V digital supply supports modern digital graphics logic, while the 3.3 V analog supply provides the operating rail for the output converters. A common full-scale-adjustment resistor sets the output range of all three channels, and a 3.8-kilohm resistor is suitable for systems targeting approximately 700 mV full-scale output levels. The 0.015-microsecond settling time supports high-speed pixel and video timing requirements. Internal circuitry generates bi-level synchronization and blanking levels for RGB and YPbPr color spaces. These functions reduce the amount of external glue logic needed when generating composite or component video signals. The parallel digital inputs accept sampled video data, while the three analog outputs provide independent red, green, and blue channels. This integration makes the THS8136 useful in graphics controllers, video splitters, frame buffers, digital display systems, and test equipment. A typical implementation places the three DAC outputs on controlled impedance PCB traces and connects the digital input bus to the graphics or video source. Designers should terminate and route the high-speed digital interface carefully because edge-rate harmonics can radiate even though the maximum sampling rate is 180 MHz. Analog and digital return currents should be managed so switching activity does not disturb the output reference. The principal design trade-off is integration versus operating flexibility. The THS8136PHP combines three converters and video-control functions in one package, reducing external circuitry, but its dedicated video feature set makes it less suitable than a general-purpose DAC when arbitrary analog waveforms, calibration, or multiple independent output ranges are required. Confirm package pin assignments and exposed-pad requirements in the manufacturer datasheet before layout release. This product overview combines the manufacturer’s device description with package, interface, output-adjustment, and ordering details that help engineers assess the THS8136PHP before designing a video DAC signal chain. It also clarifies the distinctions among same-device ordering options and pin-compatible industrial-grade variants.

RFQ संपर्क
THS8200PFP - Triple 10-Bit Video DAC | Texas Instruments
THS8200PFP

THS8200PFP - Triple 10-Bit Video DAC | Texas Instruments

Texas Instruments THS8200PFP is a triple 10-bit all-format video digital-to-analog converter in an 80-pin HTQFP (PFP) package measuring 12 x 12 mm. It converts digital component-video signals into three analog video outputs and supports 4:4:4 and 4:2:2 input formats through three, two, or one 10-bit ports. The specified operating-temperature range is 0°C to 70°C. A video DAC is the output stage of a digital video system. It belongs to the DAC and ADC/DAC hierarchy, which converts digital data into analog voltage signals for downstream displays, video processors, transmission equipment, or recording systems. For the THS8200PFP, the defining system role is the simultaneous generation of three analog video channels from component-video data while accepting multiple digital-interface configurations. Key features include three integrated 10-bit DAC channels, support for all-format component-video conversion, serial digital input, and a high-pin-count HTQFP package. The three 10-bit ports give the system designer flexibility in how video data is distributed. The 4:4:4 format carries separate component information at full resolution, while 4:2:2 support enables designs using fewer data paths when the source format permits it. The device is intended for complete video back-end conversion applications, including DVD players, personal video recorders, set-top boxes, and other systems that require digital component-video signals to become analog outputs. Its parallel operational architecture consolidates three conversion channels into one dedicated video-processing component rather than requiring three separate converter packages. Typical deployments include consumer video equipment, broadcast and monitoring systems, and legacy digital-video infrastructure transitioning to analog displays or processors. System designers should also account for synchronization, digital input timing, analog-output quality, reference-clock integrity, and correct handling of unsupported or unused channels when creating the board-level interface. Layout is especially important because an 80-pin HTQFP provides many digital and analog connections in a compact 12 x 12 mm footprint. Maintain short return paths for analog outputs, provide continuous supply planes where possible, decouple supply pins close to the device, and follow the manufacturer's pin-description and layout guidance when assigning traces. The exposed thermal pad and package outline must follow the land pattern specified for the PFP package. This product page combines the exact manufacturer identity, package and temperature information, sourcing structure, compatible family members, and application-specific design guidance. It also distinguishes documented functionality from electrical parameters that must be confirmed in the manufacturer datasheet before final schematic, signal-integrity, or thermal sign-off.

RFQ संपर्क
THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments
THVD1400DR

THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments

The Texas Instruments THVD1400DR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package, supporting data rates up to 500 kbps with integrated ±12-kV IEC ESD (HBM) protection on the bus pins. The part contains one driver and one receiver on a single die, operates from a 3.0 V to 5.5 V supply, and meets or exceeds the requirements of the TIA/EIA-485A standard for robust industrial communication. The wide common-mode voltage range and low input leakage on bus pins make the device suitable for multi-point applications over long cable runs. What is an RS-485 transceiver? An RS-485 transceiver is a type of differential line driver/receiver interface IC that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 belongs to the broader TIA/EIA-485 family of serial interface standards and is widely used in industrial automation, building control, and long-distance communication. The transceiver sits between a UART/MCU and the physical bus, providing the voltage translation, drive strength, and ESD protection required to survive harsh electrical environments. Key features include 1/8 unit load support (allowing up to 256 nodes on the bus), ±12-kV IEC 61000-4-2 contact discharge ESD protection on bus pins, hot-plug support with glitchless power-up, and an extended industrial operating temperature range of -40 °C to +125 °C. The THVD1400DR also integrates thermal shutdown, current limiting on driver outputs, and receiver fail-safe for open, shorted, or idle bus conditions, eliminating the need for external biasing resistors on many designs. The architecture combines a precision differential line driver with a high-CMRR receiver and on-chip charge-pump-generated drive rails. The wide bus common-mode range of -7 V to +12 V lets the device tolerate ground potential differences between nodes across long cable runs. The 8-pin SOIC footprint provides drop-in compatibility with industry-standard pinout, simplifying PCB reuse and second-sourcing. Typical applications include industrial fieldbus networks (Modbus, Profibus-compatible), HVAC building automation, solar inverter daisy-chains, motor drive control links, smart-grid metering, and any point-to-point or multi-drop RS-485 link requiring IEC-grade ESD robustness. The low quiescent current also makes it suitable for battery-backed or always-on telemetry nodes. When designing with this device, place 100 nF decoupling close to VCC and add a 1 µF bulk capacitor when long supply traces are present. For bus termination, use a 120 Ω resistor across the differential pair at the two end nodes only; intermediate nodes should not be terminated to preserve signal integrity on multi-drop buses.

RFQ संपर्क
THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments
THVD1450

THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments

The Texas Instruments THVD1450 is a 3.3-V to 5-V, half-duplex RS-485/RS-422 transceiver with ±18-kV IEC ESD protection, delivering data rates up to 50 Mbps in an 8-pin SOIC (D) package. It belongs to the THVD14xx family of noise-immune transceivers engineered for rugged industrial environments and supports a wide 3 V to 5.5 V supply range with a low-current standby mode for power-constrained designs. An RS-485 transceiver is a physical-layer device that converts a single-ended UART signal into a balanced differential signal for transmission over twisted-pair cabling, enabling robust communication across long distances and electrically noisy industrial settings. The RS-485 standard (TIA/EIA-485) defines a differential bus topology that allows up to 32 unit loads (256 with modern transceivers) on a single twisted pair, with common-mode voltage range of −7 V to +12 V and cable lengths beyond 1200 m at reduced speeds. Transceivers sit at the bottom of the OSI physical layer (PHY) and above the UART/SCI controller, framing all fieldbus, PROFIBUS, Modbus, BACnet, and DMX512 wiring as the dominant industrial multi-drop PHY in use today. Key features of the THVD1450 include ±18-kV IEC 61000-4-2 air-discharge ESD on bus pins (eliminating external TVS arrays), ±8-kV IEC contact discharge, integrated bus fail-safe biasing (open, short, idle), 1.5 V typical differential output swing into 54 Ω, hot-plug support with glitch-free power-up, and an operating junction temperature range of −40 °C to +125 °C. The 8-SOIC package provides a compact 3.9 mm × 4.9 mm footprint, suitable for point-to-point and multi-drop fieldbus links. Architecturally, the THVD1450 integrates a differential line driver, a wide-common-mode differential receiver, internal fail-safe bias resistors, and an IEC-ESD cell at the bus pins. The wide 3 V to 5.5 V supply range allows direct connection to either 3.3-V MCU rails or legacy 5-V logic, simplifying BOM in mixed-voltage industrial nodes. Typical applications include factory-automation fieldbus nodes, building-automation BACnet wiring, solar inverter daisy-chain comms, motor-drive encoder feedback, smart-meter data concentrators, and any noise-immune multi-drop RS-485 link where bus pins face direct human/operator contact and require maximum ESD survivability. The 50-Mbps speed grade also supports high-rate motion-control and vision-system links over short cable. When designing with this part, place 100 nF decoupling within 2 mm of VCC and add a 120 Ω termination resistor at each cable end only. Avoid stubs longer than one-tenth of the driver rise time to prevent reflections at 50 Mbps, and never tie the bus pins to a stub that exceeds the unit-load budget of 32 (or 256 with low-IU parts). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including same-family THVD14xx options, cross-brand pin-compatible RS-485 transceivers, and IEC-ESD design-in guidance for rugged industrial nodes.

RFQ संपर्क
THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI
THVD1450D

THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI

The Texas Instruments THVD1450D is a 3.3-V to 5-V RS-485/RS-422 transceiver housed in an 8-pin SOIC package, featuring integrated IEC 61000-4-2 ±18-kV ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 configuration) in half-duplex mode and supports data rates up to 50 Mbps over a wide 3.0V-5.5V supply range. An RS-485/RS-422 transceiver is a physical-layer interface IC that translates logic-level UART or SPI signals from a microcontroller into the differential voltage signaling required by the RS-485 and RS-422 standards. Differential signaling allows data transmission over long cable runs (up to 1200 m per the RS-485 standard) in electrically noisy industrial environments, because common-mode noise is rejected by the receiver's differential comparator. Within the broader system hierarchy, the transceiver sits between the controller's UART/SPI logic and the physical twisted-pair bus, sitting alongside other power-management and interface ICs on the bus node's BOM. Key features include ±18-kV HBM-equivalent IEC 61000-4-2 ESD protection on the A and B bus pins, ±4-kV IEC 61000-4-4 EFT immunity, a 30-mV receiver hysteresis for noise rejection, and a wide -40°C to +125°C operating temperature range. The wide 3.0V-5.5V supply range makes the part compatible with both 3.3V and 5V MCU rails without level shifters, while the 1/1 half-duplex configuration is the most common building block for daisy-chained or point-to-point RS-485 nodes. The device architecture uses a differential line driver with controlled slew rate to limit EMI, and a differential comparator receiver with 30-mV hysteresis to reject bus noise and reflection-induced ringing. The integrated IEC 61000-4-2 ESD cells on the bus pins (tolerant to ±18 kV contact/air discharge) eliminate the need for external TVS protection in most industrial installations, reducing BOM cost and PCB area. The part is part of TI's THVD14xx family, which shares pinout and feature set across data-rate grades. Typical applications include industrial factory automation, HVAC networks, building-automation RS-485 trunks, motor-control encoder feedback, smart-grid metering, and any embedded system that needs a rugged 3.3V/5V RS-485 node with strong system-level ESD/EFT immunity. When designing with this device, place 100-nF decoupling capacitors as close as possible to the VCC pin and follow RS-485 cable-stub length recommendations. Note that the wide-supply 3.0V-5.5V range allows direct connection to both 3.3V and 5V MCUs, but the bus common-mode voltage must remain within the -7V to +12V range defined by the standard. This page synthesizes distributor stock, drop-in alternatives, and practical design notes that complement the manufacturer datasheet with real BOM-level guidance.

RFQ संपर्क
THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI
THVD1450DRBR

THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI

The Texas Instruments THVD1450DRBR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver housed in an 8-pin VSON EP (DRB) package measuring 3x3 mm, supporting data rates up to 50 Mbps with integrated ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It operates from a single 3-V to 5.5-V supply and provides one driver and one receiver (1/1) on a shared differential bus pair for two-wire multi-drop topologies. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between a single-ended UART/logic signal on the controller side and a differential voltage on a twisted-pair cable. Half-duplex operation means the same differential pair is shared between transmit and receive paths, reducing wire count for multi-drop industrial networks such as Modbus RTU, Profibus, and DMX512. Within the broader signal-chain taxonomy, the THVD1450 belongs to the transceiver -> line driver/receiver -> interface IC -> power-tree signal-chain hierarchy used in industrial automation, building automation, and point-of-sale equipment. Key differentiating features include ±18-kV IEC 61000-4-2 contact/air ESD immunity on the bus pins, ±4-kV IEC 61000-4-4 EFT immunity, and a wide 3-V to 5.5-V supply range that allows direct connection to 3.3-V MCUs or 5-V legacy controllers without external level shifters. The integrated fail-safe biasing on the receiver guarantees a known logic-high output when the bus is idle, shorted, or open. The 8-pin VSON EP package with exposed thermal pad occupies only 3x3 mm, suitable for dense fieldbus nodes and compact sensor modules. The architecture uses a differential line driver with controlled slew rate and a differential comparator receiver with 30 mV of hysteresis for noise rejection. The wide common-mode range (typically -7 V to +12 V) tolerates ground-potential differences between nodes on long cable runs, while the 1-unit-load receiver (32 nodes) supports large multi-drop networks within Modbus-style installations. Typical applications include industrial fieldbus networks, motor-drive feedback links, building-automation gateways, solar inverter monitoring, and any cable link requiring IEC-rated ESD/EFT robustness. The bus pins survive ±18-kV contact discharge per IEC 61000-4-2, eliminating external TVS diode arrays in many designs. When designing with this part, place a 100 nF decoupling capacitor close to VCC, respect the DRB exposed-pad layout for thermal spreading, and rely on the internal fail-safe biasing rather than an external resistor network. The wide common-mode range means most cable installations work without additional protection circuitry. This page consolidates distributor pricing, drop-in alternatives in the same 8-VSON footprint, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI
THVD1451DRBR

THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI

The Texas Instruments THVD1451DRBR is a 3.3-V to 5-V RS-485 transceiver housed in an 8-pin VSON (DRB) package with 3x3 mm footprint, featuring ±18-kV IEC 61000-4-2 ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 transceiver), supports half-duplex communication, and operates across a wide 3.0 V to 5.5 V supply range compatible with both 3.3 V and 5 V system rails. An RS-485 transceiver is a physical-layer interface IC that converts differential bus signals to single-ended logic levels, enabling robust half-duplex or full-duplex serial communication over twisted-pair cabling in electrically noisy industrial environments. RS-485 belongs to the broader TIA/EIA-485 standard family of differential transceivers, used as the physical layer for protocols such as Modbus RTU, PROFIBUS, DMX512, and BACnet. The THVD1451 sits within TI's THVD family, which adds integrated IEC ESD protection that eliminates external TVS diodes in many designs. Key features include ±18-kV IEC 61000-4-2 contact discharge ESD protection on the bus pins, ±8-kV IEC 61000-4-2 air-gap discharge, ±4-kV EFT, and ±1.5-kV surge (2 Ω source). The device supports up to 50 Mbps signaling rate, features a low standby current of < 5 µA, and offers 1/8 unit-load fanout supporting up to 256 nodes on a single bus. Thermal and fault protection includes thermal shutdown, current limiting on driver outputs, and bus pin fail-safe biasing that keeps the receiver output in a defined state when the bus is floating. The THVD1451 uses a 3.3 V/5 V CMOS process with precision differential line drivers, achieving low driver skew and rail-to-rail common-mode range from -7 V to +12 V on the bus. The wide common-mode tolerance makes the device tolerant of ground potential differences between nodes in long-cable runs, a defining requirement of the RS-485 standard. The integrated IEC 61000-4-2 ESD protection reduces board area and BOM cost by replacing discrete TVS arrays. Typical applications include factory automation PLCs, building automation HVAC controllers, solar inverter communication gateways, smart-grid metering, and motor drive encoder feedback links. The wide supply and common-mode ranges also support battery management system (BMS) daisy-chained monitoring where nodes see different ground references. Design tip: place the THVD1451 as close as possible to the bus connector with a solid ground pour beneath the exposed pad to maximize ESD dissipation. For full ±18-kV IEC contact discharge protection the PCB ground must be low-impedance; a stitching capacitance of 1 nF Y1-rated between bus ground and chassis is recommended. This page synthesizes distributor pricing, drop-in alternatives and design notes not found in the manufacturer datasheet alone, helping engineers select pin-compatible RS-485 ICs with comparable ESD ratings for industrial and factory-automation designs.

RFQ संपर्क
THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI
THVD1452D

THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1452D is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, housed in a 14-pin SOIC (D) package. The device integrates one driver and one receiver (1/1) in a full-duplex configuration, supporting data rates suitable for factory automation, motor drive, and industrial process control networks. The wide 3.0-V to 5.5-V supply range allows direct interfacing to 3.3-V MCUs as well as legacy 5-V UARTs without level shifters. An RS-485 transceiver is a differential line driver/receiver IC designed for robust, long-distance, half- or full-duplex serial communication over twisted-pair cabling. RS-485 transceivers belong to the interface IC family within the broader semiconductor hierarchy (interface IC -> communication transceiver -> differential bus transceiver -> semiconductor). They convert single-ended TTL/CMOS logic levels into differential signals compliant with the TIA/EIA-485 standard, enabling multi-drop networks of up to 32 unit loads on a single bus segment with excellent immunity to common-mode noise. Key features of the THVD1452D include ±18-kV IEC 61000-4-2 ESD protection on the bus pins (HBM ±16 kV, contact discharge ±6 kV), a 1/8 unit-load receiver input impedance allowing up to 256 nodes on the bus, true fail-safe biasing on the receiver outputs, and integrated IEC 61000-4-4 EFT protection. The device operates across the industrial -40 °C to +125 °C temperature range and provides thermal shutdown with automatic recovery. The architecture combines a precision differential line driver with a wide-common-mode receiver that detects signals as low as ±200 mV in the presence of ±25 V common-mode voltage. This robust receiver design eliminates the need for external fail-safe resistors and supports reliable operation in electrically noisy industrial environments such as motor inverters and HVAC equipment. Typical applications include factory automation networks, motor drive position feedback, building automation (HVAC, lighting, access control), solar inverter communications, and any point-to-point or multi-drop RS-485 link requiring strong system-level ESD/EFT robustness without external protection components. When designing with the THVD1452D, place the bus pins' decoupling capacitor as close as possible to VCC (pin 13) and route the differential A/B traces as a 100-Ω differential pair with ground reference. Use a 120 Ω resistor across A and B at the cable ends for termination. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
THVD1452DGSR - 3.3-5V RS-485 Transceiver, 50Mbps, ±18kV ESD | TI
THVD1452DGSR

THVD1452DGSR - 3.3-5V RS-485 Transceiver, 50Mbps, ±18kV ESD | TI

The Texas Instruments THVD1452DGSR is a 3.3-V to 5-V RS-485/RS-422 transceiver with integrated ±18-kV IEC ESD protection, packaged in a 10-pin VSSOP (DGS). It supports data rates up to 50 Mbps in half-duplex or full-duplex topologies, with a 3 V to 5.5 V supply range that is compatible with both 3.3-V and 5-V microcontroller I/O rails. The THVD1452 variant provides active-high driver enable (DE) and active-low receiver enable (RE) pins for flexible bus direction control in multidrop RS-485 networks. An RS-485 transceiver is a differential line driver/receiver IC that converts single-ended logic-level signals (UART, SPI, or general-purpose GPIO) into robust differential signaling on twisted-pair cables, enabling reliable communication over long distances (up to 1200 m at lower data rates) in electrically noisy industrial environments. RS-485 belongs to the TIA/EIA-485 family of standards and is one of the most widely used physical layers in industrial automation, building automation, and process-control networks. Key features include ±18-kV IEC 61000-4-2 air-gap ESD on the bus pins (with HBM ESD also exceeding typical RS-485 levels), 1/8 unit-load support for up to 256 nodes on the bus, glitch-free power-up/power-down to avoid bus contention, and wide bus-pin common-mode range that survives ground potential differences between nodes. The device draws a low quiescent current in standby and offers thermal shutdown protection. The 10-pin VSSOP (DGS) package is thermally enhanced and footprint-compatible with the wider THVD14xx family, enabling a single PCB layout to support pin-compatible device variants of different data rates or enable schemes. Architecture is built on a BiCMOS process that combines the high drive strength of bipolar outputs with the low power consumption of CMOS logic, achieving < 1 mA quiescent current when both driver and receiver are disabled. The internal differential driver maintains the TIA/EIA-485-2017 minimum 1.5 V differential output over a 54 Ω load, while the receiver's wide input common-mode range tolerates ground shifts in large bus installations. Typical applications include factory automation networks (Modbus, PROFIBUS), solar inverter communications, HVAC building controls, grid infrastructure metering, and any 3.3-V or 5-V microcontroller needing a robust differential communication port. Industrial 24-V PLC backplanes and motor-drive feedback links also benefit from the part's high noise immunity. When designing with this device, terminate the bus with 120 Ω resistors at both ends (matched to the characteristic impedance of the twisted pair), place 100 nF decoupling capacitors as close as possible to the VCC pin, and use series fail-safe biasing resistors only if the master/slave node count or cable capacitance makes true fail-safe bias impractical. This page synthesizes distributor pricing, parametric comparison against the broader THVD14xx family and pin-compatible competitors (MAX3485, ISL3179, LTC2855 families), and practical layout guidance beyond the manufacturer datasheet.

RFQ संपर्क
THVD1452DR - 3.3-5V RS-485 Transceiver, ±18kV ESD, SOIC-14 | TI
THVD1452DR

THVD1452DR - 3.3-5V RS-485 Transceiver, ±18kV ESD, SOIC-14 | TI

The Texas Instruments THVD1452DR is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, packaged in a 14-pin SOIC (D) with one driver and one receiver (full-duplex) per channel. It operates from a 3.0 V to 5.5 V supply, supports data rates up to 50 Mbps, and offers ±18 kV IEC 61000-4-2 air-gap ESD and ±8 kV IEC contact discharge on the bus pins. The device is specified over the -40°C to +125°C industrial temperature range and supports up to 256 bus nodes. An RS-485 transceiver is a differential line driver/receiver that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 is the de-facto physical layer for industrial multi-drop communication (e.g., Modbus, PROFIBUS, DMX512, BACnet), valued for its robustness, long cable reach (up to 1200 m at lower speeds), and noise immunity. The THVD1452 family belongs to TI's THVD14xx portfolio of 3.3-V/5-V dual-supply transceivers, sitting within the broader Interface IC hierarchy: line transceiver -> RS-485 transceiver -> differential interface IC -> semiconductor. Key features of the THVD1452DR include 1/8 unit load (allowing up to 256 devices on the bus), true fail-safe biasing that guarantees a known receiver output when the bus is idle/shorted/open, hot-swap glitch-free bus pins, a wide common-mode range of -7 V to +12 V, and a low quiescent current. Integrated ±18-kV IEC 61000-4-2 ESD eliminates external TVS diodes in many designs, reducing BOM cost and board area for industrial nodes. The transceiver uses a fully balanced differential architecture with slew-rate-limited driver outputs to reduce EMI. An internal common-mode voltage reference and fail-safe resistors on A/B ensure deterministic receiver output regardless of bus state, while the 1/8 unit-load input impedance allows large multi-drop networks without exceeding the RS-485 32-unit-load minimum. The wide 3.0-5.5 V supply range means the same part can be powered from 3.3-V MCUs or 5-V legacy controllers without level shifters. Typical applications include factory-automation fieldbus nodes (Modbus RTU, PROFIBUS), building-automation BACnet MS/TP segments, solar inverter daisy-chains, smart-meter AMI networks, motor-drive encoder links, and any industrial I/O link requiring IEC-level ESD immunity. Designers also use it in DMX512 stage-lighting nodes and HVAC damper-actuator networks. When laying out the THVD1452DR, route the differential A/B pair as a 100-Ω matched impedance, keep the bus stub length below one-tenth of the driver rise time, and place a 100 nF decoupling cap close to VCC. Although the part integrates ±18-kV IEC ESD, a small common-mode choke and a 100 Ω series resistor on each bus pin add extra margin in harsh electrical environments and reduce radiated emissions.

RFQ संपर्क
THVD1510DR - 5V RS-485 Transceiver, ±18kV ESD, SOIC-8 | Texas Instruments
THVD1510DR

THVD1510DR - 5V RS-485 Transceiver, ±18kV ESD, SOIC-8 | Texas Instruments

The Texas Instruments THVD1510DR is a 5V RS-485/RS-422 half-duplex transceiver housed in an 8-pin SOIC package with integrated ±18kV IEC 61000-4-2 ESD protection on the bus pins. It delivers up to 10 Mbps signaling, 1 driver and 1 receiver per channel (1/1 configuration), and operates from a single 4.5V to 5.5V supply drawing a typical quiescent current of under 1 mA. The DR suffix designates the small-outline (SOIC-8) tape-and-reel packaging option. An RS-485 transceiver is a differential line driver/receiver IC that enables robust half-duplex or full-duplex serial communication over twisted-pair copper media. RS-485 belongs to the TIA/EIA-485 standard family of balanced digital interfaces used in industrial fieldbus, building automation, motor control, and remote sensor backbones. As a physical-layer interface IC (PHY-LVL interface), it sits between an application MCU's UART and the physical twisted-pair bus, providing the voltage-level translation, common-mode range, and noise immunity that UART logic alone cannot deliver over long distances. Key features include ±18kV IEC ESD on bus pins (HBM 16kV on A/B), ±70V fault tolerance, an extended common-mode range of ±25V, true fail-safe receiver topology, and 1/8 unit-load support allowing up to 256 nodes on a single bus. The half-duplex architecture integrates a single differential driver and a single differential receiver sharing one bus pair (A/Y, B/Z), minimizing board area. Industrial operating temperature spans -40C to +125C, supporting outdoor and factory-floor deployment. The THVD1510 uses a charge-pump-assisted driver architecture to drive the bus with 5V signaling independent of supply voltage. The receiver's true fail-safe topology guarantees a logic-high output when the bus is shorted, open, or idle, eliminating the need for external bias resistors. Internal hot-plug protection prevents inrush current during board insertion into energized backplanes. Typical applications include industrial fieldbus nodes (Modbus RTU, Profibus DP, BACnet MS/TP), solar inverter string monitoring, EV charging station communication, smart-meter AMI concentrators, HVAC controllers, motor-drive CAN-bridge interfaces, and any point-to-point or multipoint RS-485 link operating up to 10 Mbps. The wide common-mode range and ±18kV ESD rating simplify design for IEC 61000-4-2 compliant installations. When designing with this part, verify that cable stub length stays below recommended budgets at 10 Mbps to avoid reflections, and provide a 100 nF decoupling capacitor within 5 mm of VCC. For 256-node configurations, ensure total bus capacitance does not exceed the unit-load budget. The fail-safe receiver eliminates external bias resistors. This page synthesizes distributor pricing, drop-in alternatives including same-family THVD15xx members and cross-brand equivalents, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
THVD1550 - 5V RS-485 Transceiver, 50Mbps, ±18kV IEC ESD | TI
THVD1550

THVD1550 - 5V RS-485 Transceiver, 50Mbps, ±18kV IEC ESD | TI

The Texas Instruments THVD1550 is a 5-V half-duplex RS-485 transceiver with integrated ±18-kV IEC 61000-4-2 contact ESD protection, packaged in an 8-pin SOIC (SOIC-8 / D package). It supports data rates up to 50 Mbps and is designed for noise-immune operation in rugged industrial environments. An RS-485 transceiver is a bus-interface IC that converts a single-ended UART/logic signal into a differential signal on a twisted-pair cable, enabling robust multi-drop communication over long distances. Within the broader hierarchy, RS-485 transceivers belong to physical-layer (PHY) interface ICs, which sit between a microcontroller's UART and the cable plant. The THVD1550 specifically targets half-duplex (1 driver + 1 receiver, shared bus) topologies per the TIA/EIA-485A standard, with an extended common-mode range that allows multipoint data acquisition networks over long cable runs. Key features include a wide 3.0 V to 5.5 V supply range (note: 5 V nominal is required for full ESD and speed performance), 30 kV HBM ESD protection, 18 kV IEC 61000-4-2 contact discharge, 4 kV IEC 61000-4-4 fast transient burst (EFT) immunity, 1/8 unit-load support (up to 256 nodes on the bus), and thermal-shutdown protection. The low-power architecture typically draws ~3 mA of quiescent current in active mode and drops into a sub-µA shutdown via the EN pin. Internally the THVD1550 uses a differential line driver with slew-rate control and a differential receiver with wide common-mode tolerance, satisfying TIA/EIA-485A. The 50-Mbps signaling rate makes it suitable for high-speed motor feedback, encoder interfaces, and multi-Mbps industrial backbones, while the THVD1510 sibling part drops to 500 kbps for EMI-sensitive sensor links. Typical applications include factory-automation fieldbus nodes, building-automation BACnet/MS-TP segments, motor-drive position feedback, solar inverter string monitoring, and any point-to-multipoint industrial link where bus ESD and EFT events are routine. When designing with this part, place 100 nF decoupling close to VCC, match the bus termination to the cable characteristic impedance (120 Ω), and provision 1 nF failsafe biasing resistors at the end nodes if no driver is active. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
THVD1552D - 5V RS-485 Transceiver, ±18kV IEC ESD, 50Mbps | TI
THVD1552D

THVD1552D - 5V RS-485 Transceiver, ±18kV IEC ESD, 50Mbps | TI

The Texas Instruments THVD1552D is a 5V RS-485/RS-422 transceiver with ±18kV IEC ESD protection on the bus pins, supporting data rates up to 50 Mbps in a 14-pin SOIC (D) package. It integrates one driver and one receiver (1/1) in a full-duplex configuration, operating from a single 4.5V to 5.5V supply with a typical quiescent current of approximately 4 mA. A RS-485 transceiver is a physical-layer interface IC that converts the differential logic levels of a UART or controller into the balanced, half-duplex signaling required by the TIA/EIA-485-A standard. As a member of the RS-485/RS-422 interface IC family within the broader interface IC category and signal conditioning/isolation hierarchy, it enables robust multi-drop communication over twisted-pair cable in electrically noisy industrial environments. The THVD15xx family specifically targets rugged industrial applications where IEC-level surge, fast transient, and ESD events would otherwise require external protection components. Key features include ±18kV IEC 61000-4-2 ESD protection on bus pins, ±2kV IEC 61000-4-4 EFT immunity, a wide common-mode range of -7V to +12V allowing up to 256 nodes on the bus, and thermal shutdown with short-circuit protection on the driver outputs. The receiver failsafe design guarantees a known logic-high output when the bus is open, shorted, or idle, eliminating the need for external biasing resistors. Internally, the THVD1552D uses a differential line driver with slew-rate control suitable for 50 Mbps signaling, paired with a differential comparator receiver with 50 mV typical input hysteresis. The half-duplex architecture shares bus pins between driver and receiver, and the full-duplex variant (THVD1552) provides separate driver output and receiver input pins. Typical applications include industrial fieldbus networks (Modbus, PROFIBUS), motor drive encoder links, building automation (BACnet, KNX), solar inverter daisy-chain communications, and any point-to-point or multi-drop RS-485 link requiring IEC-level robustness. Designers typically pair it with a TVS diode array on the bus for additional surge immunity. When designing with this device, place 100 nF decoupling capacitors as close as possible to the VCC pin and add a 1 µF bulk capacitor on the bus-side supply rail. The exposed pad must be soldered to a continuous ground plane for thermal dissipation. Maintain 100 Ω termination at both cable ends to suppress reflections at 50 Mbps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
THVD1552DGS - 5V RS-485 Transceiver, ±18kV IEC ESD | TI
THVD1552DGS

THVD1552DGS - 5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1552DGS is a 5-V RS-485 transceiver with integrated ±18-kV IEC 61000-4-2 ESD protection, delivered in a 10-pin VSSOP (DGS) package with extended −40 °C to +125 °C industrial temperature support. It provides one driver and one receiver (1/1) for full-duplex RS-422/RS-485 communication at signaling rates up to 50 Mbps, suiting both multi-drop industrial backbones and high-speed point-to-point links. Background: an RS-485 transceiver is a physical-layer interface IC that translates a low-voltage differential logic signal on a UART or SPI controller side to the rugged, balanced differential bus levels defined by the TIA/EIA-485A standard. By sitting between the application MCU and the twisted-pair cable, it provides the bus biasing, line driving strength, and ESD/EFT immunity required for industrial environments where long cable runs pick up motor noise, lightning surges, and hot-plug transients. Key features include a 4.5 V to 5.5 V single-supply operating range, ±30-kV HBM bus-pin ESD (human-body model), ±18-kV IEC 61000-4-2 contact discharge, ±25-kV IEC 61000-4-2 air-gap discharge, and integrated IEC 61000-4-4 EFT immunity that removes the need for external TVS protection on the bus. The receiver failsafe design guarantees a known logic output when the bus is idle, shorted, or open. Architecturally, the THVD1552 uses a differential line driver with slew-rate-limited outputs and a wide-common-mode receiver that meets the TIA/EIA-485A standard, allowing up to 256 transceivers on a single bus when using lower-speed family members (the THVD1552 is optimized for higher speed). The half-/full-duplex variants in the THVD15xx family share the bus-pin ESD cell, simplifying multi-protocol design. Typical applications include factory automation PLC backplanes, motor-drive communication links, solar inverter telemetry, building-automation RS-485 trunks, and any cable runs through noisy industrial cabinets. When designing with this part, place 100 nF decoupling close to VCC and use a 120 Ω termination at the bus ends only. Total bus load (stub length and cable capacitance) limits the maximum signaling rate, so verify cable length against the 50-Mbps data-rate budget. This page synthesizes distributor stock, parametric drops-in, and field-tested design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI
THVD1552DR

THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI

The Texas Instruments THVD1552DR is a 5-V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC (D) package, integrating ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It supports a signaling rate up to 50 Mbps and operates across a wide 3 V to 5.5 V supply range, making it a robust interface for industrial and noisy environments where reliable differential communication is required. An RS-485 transceiver is a physical-layer (PHY) device that converts a single-ended UART/logic signal into a differential signal suitable for transmission over twisted-pair cabling while meeting the TIA/EIA-485 standard. This PHY sits within the broader OSI stack between the controller UART (data-link layer) and the physical medium (cable), under the family name of serial-interface ICs. The THVD1552 belongs to the THVD15xx sub-family of noise-immune TI transceivers, sharing pinouts and feature sets across half- and full-duplex variants. Key features include ±18-kV IEC 61000-4-2 contact/air-discharge ESD protection directly on bus pins (driver output and receiver input), ±4-kV IEC 61000-4-4 EFT immunity, an internal fail-safe biasing on the receiver output for open/short bus conditions, 1/8 unit-load support (up to 256 nodes on a single bus), and a wide -40 °C to +125 °C operating temperature range. The 14-SOIC footprint is industry standard for this class and supports reflow-solder assembly. The THVD1552 uses a CMOS process with integrated TVS-style ESD structures on the bus pins; this allows designers to replace external protection components, BOM cost, and PCB area. Internal fail-safe circuitry guarantees a logic-high receiver output when the bus is idle, shorted, or terminated but undriven — critical for deterministic polling protocols such as Modbus. Typical applications include motor-control feedback links, multi-drop industrial sensor buses, building automation nodes (BACnet/MS-TP, Modbus RTU), solar inverter inter-module communication, and any 3.3-V or 5-V MCU UART-to-RS-485 bridge requiring strong system-level ESD/EFT robustness. When laying out this part, place the bus-side 120 Ω termination as close to the IC bus pins as possible, route the differential pair A/B symmetrically, and keep the bus stub length under one-tenth of the signal rise time (about 30 mm at 50 Mbps) to preserve signal integrity. This page consolidates distributor stock/pricing, drop-in alternative listings, and PCB design notes not found in the TI datasheet alone, accelerating engineer selection for noise-immune RS-485 designs.

RFQ संपर्क
TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI
TIBPAL16R8-25CFN

TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI

The Texas Instruments TIBPAL16R8-25CFN is a high-performance, low-power IMPACT-X PAL (Programmable Array Logic) device from Texas Instruments, delivering 25 ns maximum propagation delay and an 8-macrocell registered architecture in a 20-pin PLCC (9x9 mm) J-leaded package. The device combines Advanced Low-Power Schottky (ALS) technology with titanium-tungsten (Ti-W) fuses, providing 64 product terms, eight D-type registered outputs, and a typical operating frequency of 30 MHz at 5.25 V supply. A PAL (Programmable Array Logic) device is a one-time-programmable (OTP) SPLD that implements custom combinational and registered logic functions through a programmable AND-OR array, preceded by fixed OR gates and fed by user-defined product-term equations. Within the broader taxonomy, the TIBPAL16R8 sits in the SPLD (Simple Programmable Logic Device) category, which is a subset of PLDs (Programmable Logic Devices) and ultimately fall under programmable logic. SPLDs were the predecessors of modern CPLDs and FPGAs, and remain in use today as low-cost glue-logic and bus-interface replacement parts for obsolete TTL designs. Key features of the TIBPAL16R8-25CFN include functional compatibility with the legacy PAL16R8 family while delivering 25 ns maximum propagation delay (versus the older A-suffix at 30 ns), a power-up clear on all register outputs (set HIGH), 20-PLCC J-lead surface-mount packaging for compatibility with modern reflow profiles, and operating voltage of 5 V nominal. Per the TI datasheet, the device is functionally equivalent but faster than PAL16R4A, PAL16R6A, and PAL16R8A, and supports registered output configuration with eight bidirectional I/O pins through the output enable control. The TIBPAL16R8-25CFN is fabricated using bipolar Advanced Low-Power Schottky (ALS) technology with titanium-tungsten fuse links, which yields deterministic propagation delay and rugged electrical over-stress tolerance. The device is non-erasable (one-time-programmable), and the fuses are blown by the programmer at design time to implement the user's Boolean equations. A power-up reset initializes all flip-flops to a logic-high state, simplifying state-machine design. Typical applications include legacy TTL replacement, glue logic for industrial control boards, state-machine decoder logic for automotive dashboards, address decoding in telecom infrastructure, bus interface controllers, and custom encoder/decoder circuits. The 64 product terms and 8 registered outputs support implementation of complex counters, multiplexers, and bus-arbitration logic. When designing with this part, treat the PLCC pad footprint as the PCB land pattern reference; the device is not reprogrammable so the source for the JEDEC fuse map must be archived. Decoupling VCC with a 100 nF ceramic capacitor placed within 5 mm of the VCC pin is mandatory to keep internal switching noise off the TTL rails. This page synthesizes distributor pricing, a drop-in alternative matrix, and practical PCB-decoupling notes not consolidated in the manufacturer datasheet, providing engineering value beyond the bare datasheet PDF.

RFQ संपर्क
TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments
TIC10024QDCPRQ1

TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments

The Texas Instruments TIC10024QDCPRQ1 is an automotive-grade 35-V Multiple Switch Detection Interface (MSDI) with SPI, housed in a 38-pin HTSSOP package with exposed thermal pad (DCP). It monitors 24 direct switch inputs (10 configurable for ground- or supply-referenced switches), integrates adjustable wetting current sources per channel, and reports switch state through an SPI-compatible serial port — eliminating up to 24 discrete comparator/MCU GPIOs in a BCM (Body Control Module). A Multiple Switch Detection Interface (MSDI) is a mixed-signal ASSP that bridges mechanical switches (e.g. rocker switches, momentary buttons, limit switches) to a microcontroller in 12-V automotive electrical systems. It belongs to the broader hierarchy: switch interface IC → interface IC → signal conditioning IC → power management / body electronics ASSP → automotive semiconductor. The MSDI provides per-input wetting current to prevent contact oxidation, programmable threshold comparators for switch-closed detection, and serial aggregation of 24 inputs into a few SPI pins — reducing wire harness complexity and MCU pin count. Key features include 35-V absolute maximum load-dump tolerance (12-V nominal), adjustable wetting current per channel, selectable ground- or supply-referenced inputs on 10 channels, integrated input debounce / de-glitch filters, configurable interrupt generation for wake events, low quiescent current sleep mode, and SPI communication up to [DATA_NEEDED: SPI clock rate]. The device operates across -40 °C to +125 °C ambient (AEC-Q100 Grade 1) and includes thermal shutdown protection. The exposed-pad HTSSOP-38 package provides theta_JA suitable for BCM thermal environments. Technically, the TIC10024-Q1 uses a per-channel comparator architecture with current-mode wetting sources driven from a shared internal regulator. The SPI peripheral implements a standard mode-0 protocol with a frame-format error flag and a global wake-up interrupt output. Internal state machine handles input filtering, hysteresis, and wetting-current modulation; channel configuration registers enable per-input current programming and pull-up/pull-down selection. Typical applications include automotive body control modules (BCM) reading 24 switches per chip, gateway/zonal controllers monitoring door/trunk/hood latches, steering-wheel switch matrices, seat-control switch aggregation, and overhead-console button clusters. The 24-input density lets a single MSDI replace multiple 8-/16-channel general-purpose I/O expanders. When designing with this part, ensure the PCB layout accommodates the exposed thermal pad with at least 4 thermal vias to the inner ground plane for AEC-Q100 thermal conformance. The 38-pin HTSSOP package requires careful routing of SPI traces; keep the SCLK/MOSI/MISO bundle length-matched and routed away from VBAT-switching nodes. This page synthesizes distributor pricing (as of 2026-10-11), drop-in same-package alternatives, and practical AEC-Q100 design notes — information not consolidated in the TI datasheet alone.

RFQ संपर्क
TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP
TIR1000IPWR

TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP

The Texas Instruments TIR1000IPWR is a standalone IrDA (Infrared Data Association) SIR (Serial Infrared) encoder/decoder IC housed in an 8-pin TSSOP (PW) package and rated for the -40C to +85C industrial temperature range. It encodes and decodes asynchronous UART bit streams into IrDA-compliant 3/16 pulse-modulated optical signals at data rates from 1200 bps up to 115.2 kbps, and operates from a 2.7 V to 5.5 V supply. The TIR1000IPWR is the tape-and-reel (R) packaging variant of the TIR1000IPW die, which is functionally identical to the legacy TIR1000IPWRG4. An IrDA encoder/decoder is a specialized interface IC that sits between a host microcontroller's UART and an external infrared transceiver (typically a PIN photodiode + LED pair). It performs the bit-stuffing and pulse-width modulation required by the IrDA physical layer so the host CPU only sees a transparent serial stream; the broader category belongs to interface ICs in the connectivity hierarchy (interface IC > transceiver > encoder/decoder). Key features include 1200-bps to 115.2-kbps IrDA 1.0 / HPSIR compliance, single 2.7 V to 5.5 V supply, direct UART handshake interface, low-power shutdown mode, and CMOS construction. The TIR1000IPWR adds an infrared port to any standard UART, eliminating the need for bit-banging IR protocols in firmware and offloading real-time pulse-width timing from the host MCU. The architecture uses a baud-rate generator derived from an external 16x clock (typically the UART's reference), a transmit pulse shaper that converts the UART TX bit stream into 3/16-width IR pulses, and a receive decoder that recovers the UART RX stream from the demodulated IR input. Because it is a pure logic encoder (no onboard LED driver), the host must add a discrete IR transceiver module (e.g., a TFDU4100 / HSDL-3201 class device) to drive the optical front end. Typical applications include IrDA ports on PDAs, industrial handhelds, medical data terminals, point-of-sale (POS) equipment, and consumer electronics printers. The wide supply range and 8-pin TSSOP package make it suitable for space-constrained designs that need to retrofit IrDA onto an existing UART. A key design consideration is clock sourcing. The TIR1000IPWR requires a 16x baud-rate reference clock (XCLK), which is normally derived from the host UART's baud-rate generator; if the host baud rate changes, XCLK must be reprogrammed accordingly. The IC does not include the optical transceiver, so a separate IrDA transceiver module must be added externally. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for IrDA encoder/decoder selection.

RFQ संपर्क
TJA1020T/N1 - LIN Transceiver, 8-SO | NXP Semiconductors
TJA1020T/N1

TJA1020T/N1 - LIN Transceiver, 8-SO | NXP Semiconductors

The NXP Semiconductors TJA1020T/N1 is a single LIN-bus transceiver integrated circuit packaged in an 8-pin SO package. It provides the physical-layer interface between a LIN network and a host microcontroller, converting serial data into the LIN bus signal and delivering received bus data through the RXD output. The TJA1020T/N1 is listed as a half LINbus transceiver, indicating its role as a node interface for LIN communication networks. A LIN transceiver is a mixed-signal interface device within the broader hierarchy of interface ICs, communication transceivers, and semiconductors. LIN, or Local Interconnect Network, is used for low-cost distributed control in vehicle and industrial networks. The transceiver provides the physical signaling layer between a microcontroller's serial interface and the wired LIN bus, while protocol handling, diagnostics, and higher-layer message handling remain the responsibility of the host controller. The principal product-specific features visible in the manufacturer and distributor documentation are the 8-pin SO package, LIN transceiver function, half-LINbus node role, RXD receive path, TXD transmit input, LIN bus connection, internal bus-output pull-up arrangement, and support for leader-side implementation using external components. The manufacturer describes the LIN output as being pulled high through an internal termination resistor, while a leader design can add a resistor-and-diode network between the LIN pin and a supply-related pin. Operationally, the transmit input accepts the controller's serial waveform and the device converts it into a LIN-compatible bus waveform. In the receive direction, the receiver detects the LIN bus input and transfers the recovered data to the host through RXD. The interface therefore isolates the controller from direct physical signaling while supporting bidirectional communication over a single LIN conductor relative to the vehicle ground reference. Typical uses include LIN-controlled automotive sub-networks, body electronics modules, seat and door modules, climate-control peripherals, sensor interfaces, actuator controllers, and industrial distributed-control nodes. The part is especially relevant when an existing microcontroller already implements the LIN protocol and requires a dedicated physical-layer transceiver. Its 8-pin SO package also supports compact, conventional PCB layouts where an 8-pin surface-mount footprint is available. Design attention should center on the LIN bus network, grounding, transceiver supply arrangement, and the distinction between follower and leader implementations. Follower nodes use the internal pull-up behavior described by NXP, whereas leader nodes require the appropriate external resistor and diode network. PCB traces should preserve a short, direct path to the LIN connector and maintain a continuous ground reference. The manufacturer product page should be consulted for the exact application circuit, recommended external components, and supply requirements. This page consolidates the exact package and lifecycle information, source datasheet links, interface-focused design guidance, and documented substitution information for engineers evaluating the TJA1020T/N1. Because the manufacturer marks the product as end-of-life, engineers should also plan a migration path or confirm availability through the Request a Quote form before committing to a new production design.

RFQ संपर्क
TJA1020T/VM - LIN Transceiver, 8-SO | NXP Semiconductors
TJA1020T/VM

TJA1020T/VM - LIN Transceiver, 8-SO | NXP Semiconductors

The NXP Semiconductors TJA1020T/VM is a single-channel LIN bus transceiver packaged in an 8-pin small-outline package. It integrates the physical-layer functions required to connect a low-speed serial network node, and its designated half LINbus interface supports communication between a LIN master and peripheral nodes. The device is offered as TJA1020T/VM,112 and is identified by NXP as no longer manufactured. A LIN transceiver is an interface integrated circuit that converts logic-level controller signals into the voltage waveform used on a LIN bus and converts received bus activity back into logic-level information. It belongs to the broader hierarchy of interface IC, bus transceiver, physical-layer transceiver, and semiconductor. LIN, or Local Interconnect Network, is commonly used for distributed vehicle functions and other cost-sensitive serial networks where a single-wire bus is advantageous. The TJA1020T/VM includes sleep mode as its default state after power-up. According to the manufacturer datasheet, the transceiver can be awakened remotely through the LIN pin, woken locally through the NWAKE pin, or activated directly through the NSLP pin. These three wake paths support designs in which a network node must remain low-power while still detecting an external wake request. The manufacturer datasheet also describes input filtering for the LIN, NWAKE, and NSLP pins. These filters help prevent unwanted transitions from disturbing the sleep and wake decision process, an important consideration when connecting a transceiver to vehicle wiring that can experience electrical transients and long unpowered periods. The 8-SO package also keeps the PCB footprint compact for distributed electronic control units and compact peripheral nodes. Typical uses include LIN master or peripheral nodes in automotive body systems, seat and door modules, lighting controllers, climate-control peripherals, sensor interfaces, and low-cost embedded serial networks. The sleep-first operating behavior is particularly useful in battery-powered or intermittently connected equipment where standby consumption and predictable wake-up behavior are central design requirements. Designers should use the manufacturer pin-description table and application information when assigning the LIN, supply, ground, NWAKE, and NSLP connections. Because this part is no longer manufactured, an existing design should be reviewed against the latest NXP product lifecycle information before new production commitments are made. This page brings together the device status, manufacturer documentation links, verified interface features, related drop-in candidates, and practical implementation guidance. It also distinguishes documented behavior from parameters that require confirmation in the current manufacturer datasheet.

RFQ संपर्क
TJA1021T/10/C - 10.4 kBd LIN Transceiver | NXP | SO-8
TJA1021T/10/C

TJA1021T/10/C - 10.4 kBd LIN Transceiver | NXP | SO-8

The NXP Semiconductors TJA1021T/10/C is a half LIN-bus transceiver optimized for 10.4 kBd operation and packaged in an 8-pin SO package. It supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016 communication, providing the physical-layer interface between a LIN protocol controller and an automotive or industrial LIN network. The integrated transceiver includes the LIN bus driver and receiver needed to connect a host controller to the bus. A LIN transceiver, also called a LIN physical-layer interface, converts logic-level signals from a LIN controller into the dominant and recessive states used on the physical bus. It also receives bus levels and presents compatible logic signals to the controller. Within the hierarchy of interface ICs, the TJA1021 belongs to the automotive LIN transceiver class and supports low-speed serial networking commonly used for distributed vehicle body and comfort systems. The TJA1021T/10/C is specifically optimized for the 10.4 kBd maximum transmission speed specified by SAE J2602. NXP identifies the device as compatible with the TJA1020 and MC33662 (B), which supports reuse of established LIN hardware platforms. Its LIN 2.x protocol coverage and standardized bus interface allow it to be used alongside common automotive LIN controllers, while the 8-pin SO package keeps the physical implementation compact. NXP describes the TJA1021 family as operating from 1 kBd to 20 kBd and supporting LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016. The /10 derivative emphasizes 10.4 kBd performance, while /20 derivatives emphasize the maximum 20 kBd rate. This distinction is important when the physical bus topology, transceiver selection or protocol-controller timing was designed around a particular LIN operating speed. Typical applications include automotive LIN master and slave nodes, door and seat modules, climate-control controllers, lighting modules, sensor gateways and body-control subsystems. The same physical interface can also support industrial LIN-compatible equipment where a standardized low-speed serial bus is used instead of a more complex CAN or Ethernet network. When laying out a replacement board, confirm the exact pin functions and exposed-pad requirements against the NXP manufacturer datasheet. Pay particular attention to bus termination, ground connection, supply decoupling and the controller-side logic levels; changing a LIN transceiver package variant without checking these details can create interoperability or EMC problems even when the connector appears identical. This product page combines protocol compatibility, package information, lifecycle status, verified source links and engineering-oriented selection guidance. It also identifies pin-compatible NXP family alternatives and explains when their optimized LIN baud rate or device generation changes the replacement decision.

RFQ संपर्क