CP2102N-A01-GQFN28R vs CP2102N-A02-GQFN28R तुलना
विस्तृत दोनों ओर की तुलना CP2102N-A01-GQFN28R द्वारा Silicon Labs और CP2102N-A02-GQFN28R द्वारा Silicon Labs. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
Silicon Labs
CP2102N-A01-GQFN28R - USB to UART Bridge QFN-28 | Silicon Labs
CP2102N-A01-GQFN28R ✓ सक्रियSilicon Labs
CP2102N-A02-GQFN28R USB-to-UART Bridge, QFN28 | Silicon Labs (Tape & Reel)
CP2102N-A02-GQFN28R ✓ सक्रियविशेषता तुलना
| पैरामीटर | CP2102N-A01-GQFN28R | CP2102N-A02-GQFN28R |
|---|---|---|
| ब्रांड | Silicon Labs | Silicon Labs |
| श्रेणी | Interface ICs | Interface ICs |
| लाइफसाइकिल स्थिति | सक्रिय | सक्रिय |
| स्टॉक स्थिति | — | In Stock |
| यूनिट मूल्य (USD) | — | $2.35 |
| Product Type | USB to UART Bridge Controller | — |
| Series | USBXpress | — |
| USB Standard | USB 2.0 Full-Speed (12 Mbps) | — |
| UART Interface | USB 2.0 UART | — |
| Number of UART Channels | 1 | — |
| डेटा दर | 300 baud to 1 Mbaud | — |
| Supply Voltage (VBUS) | 4.0 V to 5.25 V | — |
| Supply Voltage (VDD) | 3.0 V to 3.6 V | 3 V to 3.6 V |
| Internal Regulator Output | 3.3 V (up to ~100 mA) | 3.3 V |
| ऑपरेटिंग तापमान | -40 C to +85 C | -40C to +85C |
| पैकेज | 28-QFN (5x5 mm) with exposed pad | QFN-28 (5x5 mm) |
| माउंटिंग प्रकार | Surface Mount | Surface Mount |
| GPIO | Yes (multiple, signal-configurable) | — |
| Reset Pin | RSTb (active-low hardware reset) | — |
| On-chip Oscillator | Yes (no external crystal required) | — |
| MSL स्तर | MSL3 (per JEDEC J-STD-020) | — |
| RoHS स्थिति | Compliant | Compliant |
| Host Driver | Silicon Labs CP210x VCP driver | — |
| फ़ंक्शन | — | USB 2.0 to UART Bridge Controller |
| Protocol | — | USB 2.0 Full-Speed |
| I/O Voltage (VIO) | — | 1.8 V to VDD |
| Maximum Baud Rate | — | 3 Mbaud |
| USB Speed | — | Full-Speed (12 Mbps) |
| Digital I/O Pins | — | 7 |
| Internal Regulator Current | — | Up to 100 mA (external load) |
| Internal Oscillator | — | 48 MHz (no external crystal required) |
| ROM for Descriptors | — | 960 bytes (one-time programmable) |
| UART Data Bits | — | 5, 6, 7, or 8 (programmable) |
| Hardware Flow Control | — | RTS/CTS supported |