DG405DY+ - Dual 2:1 CMOS Analog Switch, 45 Ohm, 16-SOIC
MPN: DG405DY+ ✓ सक्रियDG405DY+ अवलोकन
An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. Unlike a mechanical relay, a CMOS analog switch changes state rapidly with no moving parts. The DG405 belongs to the analog switch hierarchy, which includes multiplexers, demultiplexers, and matrix switches. These devices are widely used to route measurements, control signals, and sensor outputs between shared circuit nodes.
Key electrical features include 45 Ohm typical on-resistance, 20 Ohm typical on-resistance in the redesigned DG405 series, low off leakage of 40 pA, and switch-on time below 100 ns. Charge injection is limited to 15 pC, while on-resistance matching and flatness are guaranteed to 2 Ohm and 3 Ohm maximum, respectively. These characteristics support accurate, high-speed signal routing without the switching transients associated with mechanical contacts.
The DG405 uses monolithic CMOS construction to combine low power consumption with fast control response. TTL-compatible inputs simplify interfacing with legacy digital logic, while CMOS compatibility supports modern controllers. Its 44 V maximum supply rating and 15 V analog signal range provide additional headroom in industrial, instrumentation, and test systems, although the precise minimum supply voltage must be confirmed in the manufacturer datasheet.
Typical uses include multiplexed measurement front ends, sample-and-hold systems, automated test equipment, and control paths where one of two signal sources must be connected to a common amplifier or converter. The device is particularly useful where switching speed and low leakage matter more than ultra-low on-resistance, such as sensor selection, video routing, and precision measurement multiplexing.
When laying out a DG405DY+ board, place input and output traces short, keep analog routing paths away from high-current switching nodes, and use a ground plane that provides a low-impedance return for control and signal currents. Verify that every signal remains within the 15 V analog range and that the supply never exceeds the 44 V maximum rating.
This page combines manufacturer and distributor product information, documented cross-reference alternatives, package details, application guidance, and design notes. It also identifies the verified electrical data and highlights the parameters that still require confirmation from the full manufacturer datasheet before a production design is released.
के लिए ड्रॉप-इन विकल्प DG405DY+ — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
DG405DY
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DG405CY+
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DG405DY-T1
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DG405DY-T1-E3
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MAX4623ESE+
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DG405DY+ Maximum Ratings और Electrical Characteristics
| Number of Circuits | 2 circuits |
| Switch Configuration | 2:1 |
| On-Resistance | 45 Ohm |
| Typical Series On-Resistance | 20 Ohm |
| Maximum Supply Voltage | 44 V |
| Analog Signal Range | 15 V |
| Off Leakage Current | 40 pA |
| Switch-On Time | Less than 100 ns |
| Charge Injection | 15 pC maximum |
| On-Resistance Matching | 2 Ohm maximum |
| On-Resistance Flatness | 3 Ohm maximum |
| Logic Compatibility | TTL and CMOS compatible |
| Supply Capability | Single supply |
| Power Consumption | Low power, milliwatt class |
| पैकेज | 16-SOIC, N |
| पिन की संख्या | 16 pins |
| Process Technology | Monolithic CMOS |
DG405DY+ 16-soic, n पिन कॉन्फ़िगरेशन गाइड
DG405DY+ (16-soic, n पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: DG405DY+.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
DG405DY+ के लिए उपयुक्त है 6 अनुप्रयोगs: Multiplexed Sensor Measurement, Automated Test Equipment Signal Routing, Sample-and-Hold Acquisition, Industrial Control Signal Multiplexing, Video and Instrumentation Signal Selection, Low-Power Portable Data Acquisition.
Multiplexed Sensor Measurement
The DG405DY+ suits front ends that select among several sensor channels with a shared amplifier or converter. Its two independent 2:1 switch circuits, 45 Ohm on-resistance, and switch-on time below 100 ns support fast channel selection, while 40 pA leakage limits the disturbance applied to high-impedance sources. Place the switch close to the sensor input to minimize parasitic capacitance and allow the following amplifier to settle after each selection. Because charge injection is specified at 15 pC maximum, include acquisition time or an input stage that tolerates the resulting transient. The 15 V analog signal range is suitable for many industrial sensor outputs, although the source amplitude and common-mode voltage must remain within the manufacturer limits.
अनुशंसित
Automated Test Equipment Signal Routing
The DG405DY+ can route test signals between a source and a measurement path where fast, repeatable switching is more important than extremely low resistance. Its sub-100 ns switch-on time allows the instrumentation controller to reduce dead time between measurements, and the 20 Ohm typical series on-resistance is acceptable for many moderate-impedance test fixtures. The guaranteed 3 Ohm maximum on-resistance flatness and 2 Ohm maximum matching help reduce channel-dependent errors. Keep the analog path short and place termination resistors near the switch or connector to limit reflections. Account for control-driver delay and downstream settling when calculating the per-point acquisition time.
अनुशंसित
Sample-and-Hold Acquisition
The DG405DY+ is appropriate for sample-and-hold circuits that need to disconnect a changing source during the conversion period. The fast switch-on time below 100 ns supports rapid acquisition, while 15 pC maximum charge injection provides a defined bound for the switching transient. Size the hold capacitor according to the source impedance, leakage current, required settling time, and acceptable acquisition error; the 40 pA leakage specification is particularly relevant for high-impedance sources. Position the switch and hold capacitor together to minimize leakage and capacitive pickup. The digital control signal should be referenced to a quiet ground and driven with clean edges to avoid coupling into the held voltage.
अनुशंसित
Industrial Control Signal Multiplexing
The DG405DY+ can connect two controlled signal sources to a shared analog input in industrial control and monitoring equipment. TTL- and CMOS-compatible inputs allow connection to a range of controller families, while the low-power monolithic CMOS design avoids the mechanical delay and wear of relay contacts. Its 15 V analog signal range accommodates many process-control signals, and the 44 V maximum supply rating provides useful design headroom. Keep the switched node away from motor, contactor, and power-converter wiring, because those sources can couple transient noise through the high-impedance control circuitry. Verify the actual operating supply range and use a separate return path for digital control currents.
अनुशंसित
Video and Instrumentation Signal Selection
The DG405DY+ can select between two analog sources in video monitors, laboratory instruments, and compact data-acquisition systems. The less-than-100 ns switch-on time supports source transitions without mechanical-contact bounce, and the 45 Ohm on-resistance is suitable for many moderate-impedance signal paths. Its low 40 pA leakage is helpful when the selected source has a high output impedance. For high-frequency video or precision small-signal work, keep the traces short, provide a continuous ground reference, and verify bandwidth behavior in the manufacturer data. The device should be mounted close to the source connectors so that cable capacitance does not dominate the settling interval.
अनुशंसित
Low-Power Portable Data Acquisition
The DG405DY+ is suitable for portable measurement systems in which a few analog channels must be routed through a shared converter while keeping power use low. Its milliwatt-class CMOS power consumption, 40 pA leakage, and 15 pC maximum charge injection reduce the loading imposed on battery-powered sensor circuits. The compact 16-SOIC package also preserves board area compared with many discrete relay or transistor networks. Confirm the minimum supply voltage before designing it into a single-rail system, and account for level translation if the controlling microcontroller operates from a lower voltage. Keep the analog section physically separated from radio and switching-converter sections to avoid injected noise.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा DG405DY+ — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | DG405DY | DG405CY+ | DG405DY-T1 | DG405DY-T1-E3 | MAX4623ESE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated | Analog Devices / Maxim Integrated | Vishay Intertechnology | Vishay Intertechnology | Analog Devices / Maxim Integrated |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Switch Configuration | Dual 2:1 | Dual 2:1 | DG405 family analog switch | Dual 2:1 | Dual 2:1 | Dual analog switch; verify configuration against pinout |
| On-Resistance | 45 Ohm | 45 Ohm | 45 Ohm class | 45 Ohm | 45 Ohm | Not stated in the supplied compatibility source |
| Typical Series On-Resistance | 20 Ohm | 20 Ohm | 20 Ohm class | 20 Ohm | 20 Ohm | Not stated in the supplied compatibility source |
| Maximum Supply Voltage | 44 V | 44 V | 44 V class | 44 V | 44 V | Not stated in the supplied compatibility source |
| Analog Signal Range | 15 V | 15 V | 15 V class | 15 V | 15 V | Not stated in the supplied compatibility source |
| Charge Injection | 15 pC maximum | 15 pC maximum | 15 pC maximum class | 15 pC maximum | 15 pC maximum | Not stated in the supplied compatibility source |
| Off Leakage Current | 40 pA | 40 pA | 40 pA class | 40 pA | 40 pA | Not stated in the supplied compatibility source |
| Price Reference | $6.16 at 1 unit as of 2026-10-28 | Price not stated in the supplied source | Price not stated in the supplied source | Price not stated in the supplied source | Price not stated in the supplied source | Price not stated in the supplied source |
मुख्य विशेषताएँ
- Documented fast switching with low charge injection (बनामDG405DY-T1-E3)
- Guaranteed on-resistance matching and flatness (बनामMAX4623ESE+)
- Single-supply-compatible low-power CMOS implementation (बनामDG405DY)
डिज़ाइन नोट्स
Keep the switched analog nodes and the receiving amplifier input as short as practical. The DG405DY+ has a documented switch-on time below 100 ns, but that figure excludes control-driver delay and analog settling. Place optional bypass or termination capacitance directly beside the connected device rather than along a long trace. A continuous ground plane under the analog path provides a low-inductance return and reduces susceptibility to charge-injection transients.
Separate the analog routing area from clocks, relays, DC-DC converters, and digital switching outputs. The analog switch may be fast, but its control edges can couple into nearby conductors. Use a solid ground plane, route digital control signals away from high-impedance inputs, and maintain a quiet analog ground region. If the board includes a connector or long trace between the DG405DY+ and the source, place the switch on the protected side of the connector to minimize noise pickup.
Do not treat the 44 V maximum supply rating as the recommended operating supply, and do not exceed the stated 15 V analog signal range without confirmation from the complete datasheet. Also verify that the DG405DY+ terminal configuration matches the intended 2:1 routing before final routing because legacy Vishay and Maxim order codes require cross-reference against the current manufacturer pinout. Add settling time after each switch event instead of assuming the sub-100 ns transition completes the measurement.
अनुपालन जानकारी
The supplied manufacturer and distributor excerpts do not contain explicit DG405DY+ RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields must be confirmed using current manufacturer compliance documentation. The Analog Devices DG405 family page identifies the family as PRODUCTION, but production status does not establish automotive qualification.
