INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments
MPN: INA2134PA ✓ सक्रियINA2134PA अवलोकन
An audio differential line receiver is a specialized amplifier stage that rejects common-mode noise present on balanced signal pairs while preserving the wanted differential audio voltage. Its place in the signal-chain hierarchy is differential receiver → balanced audio input amplifier → analog signal-conditioning front end. This makes the INA2134PA particularly useful when a stereo source uses balanced left and right channels but the downstream circuitry requires ground-referenced, single-ended audio signals.
Key performance characteristics include a fixed 0 dB voltage gain, 90 dB minimum CMRR, 2.9 mA maximum quiescent current, and operation from -18 V to +18 V. According to the TI INA134 and INA2134 datasheet, the receiver combines low distortion with fast settling and wide output-voltage swing. The 14 V/µs slew rate supports accurate reproduction of high-level, high-frequency transients rather than clipping them under moderate loading.
The INA2134PA contains two independent receiver channels and internal precision gain-setting resistors. On-chip resistors reduce component count and help maintain consistent channel-to-channel gain without requiring external matched networks. Its differential architecture is useful for rejecting ground-potential differences and coupled interference present between a source and the receiving equipment, especially in professional audio, instrumentation, and industrial control systems.
Typical uses include stereo balanced-to-unbalanced conversion, audio measurement front ends, line-level signal conditioning, and instrumentation amplifiers. Because the gain is fixed at 1 V/V, downstream stages must provide any required attenuation or additional amplification. The device is also appropriate for prototypes, repairs, and legacy equipment where a standard 14-pin PDIP footprint and through-hole assembly are preferred over a surface-mount package.
When laying out the receiver, connect the balanced input conductors to their assigned differential inputs and route the outputs to the following analog stage with short traces and a stable ground reference. Decouple each supply rail close to the device, keep input and output nodes away from switching-current paths, and verify the output swing against the selected load. This page also organizes package, electrical, and replacement information for faster component selection.
के लिए ड्रॉप-इन विकल्प INA2134PA — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
INA2137PA
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →INA2134PA Maximum Ratings और Electrical Characteristics
| Number of Channels | 2 channels |
| Voltage Gain | 1 V/V (0 dB) |
| Architecture | Dual audio differential line receiver |
| Supply Voltage Range | -18 V to +18 V |
| क्वाइसेंट करंट | 2.9 mA maximum |
| Common-Mode Rejection Ratio | 90 dB minimum |
| Total Harmonic Distortion + Noise | 0.0005% at 1 kHz |
| Slew Rate | 14 V/µs |
| Gain Resistors | On-chip precision resistors |
| ऑपरेटिंग तापमान रेंज | -40 °C to +85 °C |
| Package Type | PDIP (N), 14 pins |
| माउंटिंग प्रकार | Through-hole |
INA2134PA pdip (n), 14 pins पिन कॉन्फ़िगरेशन गाइड
INA2134PA (pdip (n), 14 pins पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: INA2134PA.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
INA2134PA के लिए उपयुक्त है 6 अनुप्रयोगs: Stereo Balanced-to-Unbalanced Audio Conversion, Professional Audio Input Conditioning, Audio Test and Measurement Front End, Industrial Instrumentation Signal Conditioning, Broadcast and Studio Interface Electronics, Balanced Sensor and Low-Level Signal Inputs.
Stereo Balanced-to-Unbalanced Audio Conversion
The INA2134PA fits directly between a balanced stereo source and an unbalanced audio processing stage. Its two channels provide fixed 1 V/V differential gain while the 90 dB minimum CMRR suppresses common-mode voltage present on both input conductors. The 0.0005% distortion at 1 kHz and 14 V/µs slew rate preserve low-level musical detail and reduce the risk of output clipping during transients.
अनुशंसित
Professional Audio Input Conditioning
Use the INA2134PA in a professional mixing console, line-level interface, or monitor controller that accepts balanced analog audio. Because the gain is fixed at 1 V/V, the receiver changes the signal format without adding level gain. Its ±18 V supply capability supports generous headroom, while the dual-channel architecture preserves matched behavior across left and right signal paths.
अनुशंसित
Audio Test and Measurement Front End
The INA2134PA can serve as the differential input stage of an audio analyzer, oscilloscope interface, or precision measurement system. The high CMRR helps isolate a small differential test signal from common-mode noise on the source leads, while the fixed unity gain keeps amplitude relationships traceable. Its low distortion at 1 kHz and fast slew rate suit measurements involving accurate waveform reproduction.
अनुशंसित
Industrial Instrumentation Signal Conditioning
The INA2134PA is appropriate for low-level differential instrumentation signals that arrive over cable runs exposed to ground-potential differences. Its 90 dB minimum CMRR improves rejection of shared interference, and the 2.9 mA maximum quiescent current supports power-constrained analog modules. The ±18 V supply range and low 1 kHz distortion accommodate industrial signal-acquisition and process-control front ends.
अनुशंसित
Broadcast and Studio Interface Electronics
The INA2134PA suits legacy broadcast consoles, studio monitor electronics, and custom interface boards that rely on a standard through-hole footprint. Two integrated receiver channels reduce the component count for stereo link conversion, while the integrated precision resistors simplify board assembly. Its 14-lead PDIP package is also convenient for repair and retrofit work on older equipment.
अनुशंसित
Balanced Sensor and Low-Level Signal Inputs
Although designed for audio, the INA2134PA also supports precision differential sensing where the required bandwidth and amplitude remain within its specifications. The fixed 1 V/V gain preserves the differential input amplitude, and the high CMRR improves rejection of shared noise. Verify the common-mode input range, output swing, and load impedance in the TI datasheet before adapting the receiver to non-audio signals.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा INA2134PA — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | INA2137PA |
|---|---|---|
| Package | PDIP (N), 14 pins | PDIP (N), 14 pins |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 2 channels | 2 channels |
| Gain | 1 V/V fixed (0 dB) | Selectable gain; differs from fixed 1 V/V |
| CMRR | 90 dB minimum | 74 dB minimum |
| THD + Noise at 1 kHz | 0.0005% | 0.0005% |
| Mounting Type | Through-hole | Through-hole |
मुख्य विशेषताएँ
- Fixed unity-gain stereo input format conversion (बनामINA2137PA)
- Higher common-mode rejection (बनामINA2137PA)
- Through-hole package for service and prototype assembly (बनामINA2134MDREP)
डिज़ाइन नोट्स
Decouple both supply rails at the device with the capacitor network specified by TI. Keep the positive and negative decoupling loops compact so that supply-current transients do not share a long path with the differential input returns. Because the circuit can operate with bipolar supplies up to ±18 V, confirm the actual rail voltages and grounding scheme before energizing the board.
Route each balanced input pair together and connect the internal precision resistor inputs directly to their assigned pins. Avoid routing input conductors adjacent to switching-node or high-current return paths. Short output traces and a continuous ground plane reduce parasitic pickup and help preserve the receiver's common-mode rejection and low-distortion performance.
Check output-voltage headroom into the actual next-stage load before fixing the system gain. The 0 dB input stage does not provide attenuation, so a high-level source can still overload the following amplifier. Where level adjustment is needed, place a calibrated attenuator or gain-control stage after the receiver and verify the resulting noise contribution.
Do not treat the INA2134UA or INA2134MDREP as PCB drop-in replacements for the 14-pin PDIP INA2134PA; those related options use surface-mount packages. Likewise, changing to the INA2137PA can alter system gain even though it retains a similar receiver architecture. Confirm the physical footprint, gain setting, common-mode limits, and output swing for every redesign.
अनुपालन जानकारी
The manufacturer identifies the INA2134PA as an industrial-temperature audio receiver in a 14-pin PDIP package. Explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified for this orderable part.
