MAX3232CDE4 - 250 kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3232CDE4 ✗ जीवन की समाप्तिMAX3232CDE4 अवलोकन
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic-compatible outputs. It belongs to the interface IC hierarchy, where transceiver ICs bridge older differential or single-ended communication ports with modern digital systems. The MAX3232CDE4 uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 without a separate negative supply.
The principal features are two driver channels, two receiver channels, operation from a single 3 V to 5.5 V supply, and data rates up to 250 kbps. Its ±15 kV human-body-model ESD protection strengthens the interface against electrostatic discharge encountered during industrial, commercial, and communications equipment. The device operates in the RS-232 voltage domain, providing the signal conditioning needed between a host controller and an external data port.
The MAX3232CDE4 is a commercial-temperature 0 °C to 70 °C component in a 16-SOIC package. Texas Instruments identifies MAX3232E as an improved direct drop-in replacement for MAX3232, although the package and suffix must be checked before substituting a specific ordering code. Charge-pump capacitors and local bypass capacitance are part of the recommended application circuit and require careful placement near the associated pins.
Typical uses include industrial control links, configuration interfaces, test equipment, data acquisition systems, maintenance ports, and embedded-control boards that retain an RS-232 connection. At 250 kbps, it is appropriate for moderate-speed serial links rather than high-speed differential buses. The single positive supply also simplifies integration where a negative rail is unavailable.
When laying out the circuit, place charge-pump and supply-bypass capacitors close to their designated pins and keep the RS-232 driver outputs away from sensitive receiver inputs. Confirm logic levels, connector protection, cable length, and grounding because those system details determine whether the transceiver's electrical specifications translate into reliable field operation.
This page combines the device's electrical limits, package details, interface standards, lifecycle information, compatible replacements, and practical layout guidance to support component selection and board-level implementation.
के लिए ड्रॉप-इन विकल्प MAX3232CDE4 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
MAX3232ECWE
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MAX3232EIDR
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MAX3232CDE4 विशेषताएं
| Product Type | RS-232 line driver/receiver transceiver |
| Driver/Receiver Configuration | 2/2 |
| Duplex Mode | Full duplex |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV HBM |
| ऑपरेटिंग तापमान रेंज | 0 °C to 70 °C |
| पैकेज | 16-SOIC, 0.154 in (3.90 mm) width |
| माउंटिंग प्रकार | Surface mount |
| Technology | RS-232 / CMOS |
| RS-232 Compliance | TIA/EIA-232-F and ITU V.28 |
| RoHS स्थिति | Compliant |
| Lead-Free Status | Lead free |
| External Charge-Pump Capacitors | 4 × 0.1 µF |
| Supply Polarity | Single positive supply |
| Manufacturer Recommended New-Design Family | MAX3232E |
MAX3232CDE4 16-soic, 0.154 in (3.90 mm) width पिन कॉन्फ़िगरेशन गाइड
MAX3232CDE4 (16-soic, 0.154 in (3.90 mm) width पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MAX3232CDE4.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
MAX3232CDE4 के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Controller Configuration Port, Data Acquisition Equipment, Test and Measurement Console, Embedded Control Board Debug Link, Serial Adapter and Peripheral Interface, Maintenance and Service Interface.
Industrial Controller Configuration Port
The MAX3232CDE4 is suitable for connecting a controller to legacy RS-232 configuration equipment when the link operates at or below 250 kbps. Its two-driver, two-receiver arrangement supports full-duplex communication from a single 3 V to 5.5 V supply, avoiding a separate negative rail. The ±15 kV HBM ESD rating adds useful protection at an accessible equipment port, although external connector and cable protection may still be required. Place the four 0.1 µF charge-pump capacitors close to their pins and route the RS-232 outputs away from sensitive logic and analog nodes.
अनुशंसित
Data Acquisition Equipment
The MAX3232CDE4 can provide a legacy RS-232 command channel for data-acquisition equipment that requires a single positive supply and modest communication speed. Two transmit channels and two receive channels allow full-duplex command and status traffic at rates up to 250 kbps. The 3 V to 5.5 V operating range permits integration with both 3.3 V and 5 V control electronics. Because the operating range is 0 °C to 70 °C, verify the enclosure temperature and select a wider-grade MAX3232E option when the equipment operates outside that commercial range.
अनुशंसित
Test and Measurement Console
The MAX3232CDE4 fits test consoles and maintenance interfaces that communicate with RS-232 instruments at speeds up to 250 kbps. A single 3 V to 5.5 V supply simplifies low-voltage test hardware, while the two-driver, two-receiver arrangement supports full-duplex command and response traffic. The ±15 kV HBM ESD protection is valuable on bench-adjacent equipment, but it does not replace cable shielding, overvoltage protection, or properly designed grounding. Validate the logic polarity of each signal and place bypass and charge-pump capacitors directly beside the associated pins.
अनुशंसित
Embedded Control Board Debug Link
The MAX3232CDE4 can implement a dedicated RS-232 service link for an embedded-control board that retains a legacy configuration connector. The 250 kbps maximum rate is sufficient for firmware update commands, status reports, and diagnostic traffic, while the full-duplex 2/2 configuration reduces software turnaround complexity. Operating from 3 V to 5.5 V allows use with common embedded logic supplies. Confirm that the board's debug connector, cable length, and ground arrangement satisfy the system-level RS-232 requirements rather than relying only on the IC data rate.
अनुशंसित
Serial Adapter and Peripheral Interface
The MAX3232CDE4 is appropriate for a compact RS-232 adapter that bridges a modern controller with a legacy peripheral. The device's 2/2 channel arrangement provides two driver outputs and two receiver inputs, allowing bidirectional command and status connections up to 250 kbps. Its single-positive-supply operation simplifies portable and embedded adapter designs, while ±15 kV HBM ESD protection improves robustness at the connector boundary. The 16-SOIC footprint remains board-mountable, but the obsolete ordering-code status makes lifecycle planning or migration to MAX3232E important for new designs.
अनुशंसित
Maintenance and Service Interface
The MAX3232CDE4 can support a field-service port on commercial equipment that requires RS-232 connectivity for diagnostics, firmware commands, or configuration backup. Its 250 kbps data rate is appropriate for short control exchanges, and the full-duplex 2/2 architecture supports simultaneous command and response traffic. The 0 °C to 70 °C operating range covers many indoor commercial installations, but outdoor equipment may require a wider-temperature alternative. The ±15 kV HBM ESD rating supports electrostatic-discharge resilience, while connector grounding and cable protection remain system-level requirements.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा MAX3232CDE4 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MAX3232ECWE | MAX3232EIDR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Driver/Receiver Configuration | 2/2 | 2/2 | 2/2 |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Operating Temperature Range | 0 °C to 70 °C | 0 °C to 70 °C | -40 °C to 85 °C |
| RoHS Status | Compliant | Compliant | Compliant |
| Lifecycle Context | Obsolete | MAX3232E family | MAX3232E family |
मुख्य विशेषताएँ
- Compact full-duplex channel count (बनामMAX3232ECWE)
- Direct family migration path (बनामMAX3232EIDR)
- Commercial-temperature option (बनामMAX3232EIDR)
डिज़ाइन नोट्स
Place the four 0.1 µF charge-pump capacitors and the supply bypass capacitor adjacent to the pins identified in the Texas Instruments manufacturer datasheet. Keep the charge-pump loop compact and route it away from RS-232 driver outputs and sensitive receiver inputs. This arrangement minimizes switching-current trace area, reduces radiated emissions, and limits voltage disturbance at the transceiver pins.
Separate the RS-232 driver traces from clocks, ADC inputs, references, and other low-level analog signals. Driver outputs are high-voltage, high-edge-rate signals even when the data rate is only 250 kbps. Maintain a practical ground return beneath or adjacent to the interface route, use a solid ground plane, and avoid routing a driver output beneath a sensitive input on adjacent PCB layers.
Do not treat ±15 kV HBM ESD protection as complete connector protection. The application may still require surge, overvoltage, or ground-loop handling determined by the cable length and operating environment. Also verify supply sequencing, logic thresholds, driver and receiver enable states, and signal polarity. For new production, evaluate the MAX3232E family before committing to the obsolete MAX3232CDE4 ordering code.
अनुपालन जानकारी
RoHS-compliant and lead-free status are identified in the manufacturer listing. The interface is described as meeting or exceeding TIA/EIA-232-F and ITU V.28 requirements. No AEC-Q100 qualification is stated for this ordering code.