OPA2137P - Dual 1MHz J-FET Op Amp | Texas Instruments
MPN: OPA2137P ✓ सक्रियOPA2137P अवलोकन
A J-FET-input operational amplifier is an analog amplifier whose field-effect transistor input stage provides very high input impedance and low input bias current. This amplifier category belongs to the broader operational amplifier, analog signal-conditioning, and semiconductor hierarchies. OPA2137P is designed for applications where low-cost dual amplification, wide supply-voltage flexibility, and a conventional through-hole package are useful.
The OPA2137 family provides two amplifiers per package, allowing differential, filtering, buffer, and feedback-pair configurations without using two separate ICs. Its 1 MHz gain-bandwidth product supports moderate-bandwidth signal processing, while the 3.5 V/µs slew rate allows the output to change relatively quickly. The 36 V maximum total supply rating accommodates single-supply and split-supply systems when the circuit designer observes the device-specific operating limits.
The P suffix identifies the 8-pin PDIP package option shown in the product listings. This through-hole format is useful for prototypes, educational equipment, laboratory instruments, and industrial control assemblies where a socketed or leaded package simplifies inspection and replacement. The two-amplifier arrangement also reduces board-area requirements compared with two separate single-amplifier packages, although fixed-pattern through-hole layouts require additional clearance around the package body.
Typical uses include low-cost audio and communication signal conditioning, sensor-interface buffering, active filtering, analog measurement front ends, and general instrumentation. The 1 MHz bandwidth makes it most appropriate for signals that do not require the slew rate and gain bandwidth of modern high-speed precision amplifiers. Dual supplies around ±15 V are commonly associated with this series, while operation from a minimum total supply of 4.5 V supports lower-voltage designs.
Designers should verify the selected OPA2137 grade and package against the complete pin configuration before assembly. Input and output signal limits, common-mode range, output swing, supply current, and stability requirements must be checked for the actual feedback network. Decoupling capacitors should be placed close to the supply pins, while sensitive analog traces should be kept away from switching nodes and high-current return paths.
This page organizes the verified OPA2137P product information with practical configuration guidance, application fit, and same-package replacement context. It also distinguishes the dual OPA2137P from single-amplifier and quad-amplifier devices, helping engineers avoid selecting a part with the wrong channel count or pinout.
के लिए ड्रॉप-इन विकल्प OPA2137P — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
OPA2137PG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
OPA2137PA
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TL062ACP
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
OPA2137P Maximum Ratings और Electrical Characteristics
| Amplifier Type | Dual J-FET-input operational amplifier |
| Number of Amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 3.5 V/µs |
| Minimum Total Supply Voltage | 4.5 V |
| Maximum Total Supply Voltage | 36 V |
| Typical Total Supply Voltage | ±15 V |
| Minimum Total Supply Voltage, Split Supply | ±2.25 V |
| Maximum Total Supply Voltage, Split Supply | ±18 V |
| Input Stage | J-FET |
| पैकेज | 8-pin PDIP |
| माउंटिंग प्रकार | Through-hole |
| Product Series | MicroAmplifier |
OPA2137P 8-pin pdip पिन कॉन्फ़िगरेशन गाइड
OPA2137P (8-pin pdip पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: OPA2137P.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
OPA2137P के लिए उपयुक्त है 6 अनुप्रयोगs: Low-Cost Sensor Signal Conditioning, Audio Preamplifier and Mixer Circuit, Active Filter and Equalization, Laboratory Instrumentation Front End, Communications Interface Buffering, Power Supply Monitor and Control.
Low-Cost Sensor Signal Conditioning
OPA2137P is well suited to buffering sensor outputs when low input loading, dual-channel economy, and moderate signal bandwidth are priorities. Its J-FET input stage is appropriate for high-impedance sources, while the 1 MHz gain-bandwidth product supports amplification stages operating below the amplifier’s full bandwidth. Place one amplifier in the signal path and the other in a feedback or reference buffer when this reduces component count. The 4.5 V to 36 V total supply range also permits adaptation to laboratory, industrial-control, or split-supply instrumentation. Confirm the sensor’s output range against the input common-mode limits before selecting the feedback resistors.
अनुशंसित
Audio Preamplifier and Mixer Circuit
OPA2137P can implement a compact two-channel audio preamplifier or mixer stage because it combines two amplifiers, a 1 MHz gain-bandwidth product, and a 3.5 V/µs slew rate in one 8-pin PDIP package. The two channels can provide independent gain stages or one channel can serve a summing or feedback function. This device is most appropriate for general-purpose audio paths rather than wideband professional audio. Check the input bias current against high-impedance source requirements and verify output swing at the selected supply voltage. Stable feedback-network values and physical separation from switching supplies will help control distortion and channel-to-channel interference.
अनुशंसित
Active Filter and Equalization
OPA2137P is suitable for active filtering and equalization circuits that need two amplification channels but do not require high-speed operation. Its 1 MHz gain-bandwidth product provides useful closed-loop bandwidth for low-frequency filter sections, and the 3.5 V/µs slew rate supports moderate-amplitude signals. The dual package can implement cascaded sections, a Sallen-Key stage, or a two-channel equalizer. Component tolerances and the amplifier’s open-loop response will influence filter accuracy, so simulation should verify phase margin across the intended frequency range. Keep the feedback loop compact and provide local supply decoupling to reduce oscillation and noise pickup.
अनुशंसित
Laboratory Instrumentation Front End
OPA2137P can serve as an instrumentation front end in laboratory and educational equipment where ±15 V is convenient and a leaded package simplifies assembly or replacement. One amplifier can buffer the input while the other drives an offset or gain stage, reducing the number of ICs compared with a discrete approach. Its J-FET input stage and 1 MHz bandwidth are appropriate for many low-frequency measurement signals. The design must remain within the 36 V maximum total supply and the input common-mode range. Socket the device only if temperature and contamination conditions are suitable, and observe the manufacturer’s handling and soldering guidance.
अनुशंसित
Communications Interface Buffering
OPA2137P can buffer moderate-bandwidth communications signals when the system needs a dual amplifier, low-cost implementation, and operation from a single or split supply. The 1 MHz gain-bandwidth product is suitable for low-speed control, monitoring, or baseband conditioning rather than high-rate data links. The J-FET input stage minimizes loading on higher-impedance interface circuits, while the 3.5 V/µs slew rate allows reasonably fast output transitions. Use short traces, a stable ground reference, and local bypass capacitors. Before release, confirm the interface’s bandwidth, output impedance, logic levels, and common-mode range against the amplifier’s characteristics.
अनुशंसित
Power Supply Monitor and Control
OPA2137P can monitor a power rail and provide a control signal when the monitored voltage remains within the amplifier’s input common-mode range. The 4.5 V to 36 V total supply capability supports operation from several industrial rails, while the two channels can compare a divided rail voltage with a reference and amplify the error for a controller. The 1 MHz bandwidth is sufficient for many slow feedback loops, and the 3.5 V/µs slew rate provides prompt response. The design must include safe divider values, input protection, and adequate output swing. Validate loop stability and isolation from switching nodes before using the amplifier in a feedback-control path.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा OPA2137P — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | OPA2137PG4 | OPA2137PA | TL062ACP |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 2 amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers |
मुख्य विशेषताएँ
- Two amplifiers are integrated in one 8-pin PDIP package (बनामOPA137P)
- The same-family alternatives preserve the principal signal-path ratings (बनामOPA2137PG4)
- The device combines J-FET input with a 36 V total supply rating (बनामTL062ACP)
डिज़ाइन नोट्स
Treat the 8-pin PDIP footprint as a through-hole layout with adequate body clearance for soldering and inspection. Place the two bypass capacitors close to the positive and negative supply pins, with short ground returns. Because OPA2137P contains two independent amplifiers, route the channels to avoid sharing long sensitive traces; crossing or coupling between the two amplifier inputs can create crosstalk even when the device itself is operating correctly.
Do not treat the 36 V rating as permission to place any signal at 36 V. Input common-mode voltage and output swing are separate limits, and exceeding either can cause nonlinear operation or damage. Check the complete electrical characteristics for the exact OPA2137 suffix, especially when using ±15 V supplies. Also avoid substituting OPA137P or OPA4343EA by appearance alone because they have different channel counts and pinouts.
The OPA2137P has a 1 MHz gain-bandwidth product, so gain and closed-loop bandwidth must be considered together when setting signal gain. Keep feedback resistors close to the relevant amplifier pins, maintain a short ground path, and avoid routing inputs beside digital clocks or switching-regulator nodes. For active filters, simulate tolerances and phase margin because a 1 MHz amplifier leaves finite bandwidth margin for the selected filter topology.
अनुपालन जानकारी
The OPA2137 is a general-purpose operational amplifier rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the exact manufacturer product record.