OPA682P - 240MHz Fixed-Gain Buffer | Texas Instruments
MPN: OPA682P ✓ सक्रियOPA682P अवलोकन
A buffer amplifier is a specialized analog amplifier that provides high input impedance and low output impedance. It belongs to the operational-amplifier hierarchy and serves as a signal-conditioning interface between a high-impedance source and a lower-impedance destination. The OPA682P uses an internally fixed gain of either +1 or −1, according to the verified component description, allowing it to preserve a signal amplitude while providing a stronger drive capability. This fixed-gain architecture simplifies external circuitry and avoids the feedback network used with conventional voltage-feedback amplifiers.
The principal features of the OPA682P include its 240 MHz bandwidth, 6 mA operating supply current, 320 µA disabled current, and 150 mA maximum output current. Its output voltage swing is specified as ±5 V or single-supply operation. Together, these characteristics make the device useful in video and communications systems, test equipment, signal-conditioning modules, and other circuits where a high-speed, low-impedance output is required. The fixed gain also helps maintain predictable bandwidth because designers do not have to select an external feedback ratio.
OPA682P is based on a bipolar operational-amplifier architecture, as reflected in the distributor component classification. The wide bandwidth enables the buffer to preserve rapid transitions and higher-frequency signal content, while the high output-current capability can improve drive into downstream circuits. Compared with an external transistor buffer, the integrated approach reduces board area and component count. Compared with a general-purpose op-amp used as a follower, its internally fixed gain provides a more focused high-speed signal-path function.
Typical uses include video-buffer stages, communication transmitters, instrumentation, and high-speed analog test systems. In each case, the amplifier is placed between the originating signal path and a load or subsequent processing stage. The 6 mA supply current is useful in power-conscious designs, while the 320 µA disable current allows the buffer to be turned down when the signal path is inactive. Designers should still verify the complete datasheet electrical limits and operating conditions for the intended supply voltage.
A primary design consideration is output loading. Although the OPA682P can source up to 150 mA, the actual usable current and voltage swing depend on the supply rails, output impedance, load impedance, temperature, and selected output configuration. Layout should minimize trace resistance and capacitance at the output, while input and supply connections should be routed to preserve the device's high-speed performance.
This page consolidates the verified OPA682P bandwidth, current, disable-state, package, sourcing, and pricing information with practical application guidance. It also distinguishes verified specifications from parameters that remain unavailable in the supplied source data, helping engineers evaluate the part without inferring unsupported electrical values.
के लिए ड्रॉप-इन विकल्प OPA682P — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंOPA682P Maximum Ratings और Electrical Characteristics
| Amplifier Type | Wideband fixed-gain buffer amplifier |
| Number of Circuits | 1 circuit |
| Bandwidth | 240 MHz |
| Internally Fixed Gain | +1 or -1 |
| सप्लाई करंट | 6 mA |
| Disabled Supply Current | 320 µA |
| High Output Current | 150 mA |
| Output Voltage Swing | ±5 V or single-supply operation |
| Disable Function | Yes |
| Architecture | Bipolar |
| पैकेज | 8-pin PDIP |
| माउंटिंग प्रकार | Through-hole |
OPA682P 8-pin pdip पिन कॉन्फ़िगरेशन गाइड
OPA682P (8-pin pdip पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: OPA682P.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
OPA682P के लिए उपयुक्त है 6 अनुप्रयोगs: Video Signal Buffering, Communications Transmit Signal Path, High-Speed Test and Measurement, Instrumentation Signal Conditioning, Portable Signal-Chain Interface, Analog Signal Isolation and Fanout.
Video Signal Buffering
OPA682P is appropriate for a high-speed video buffer because it combines 240 MHz bandwidth with an internally fixed gain of +1 or −1 and a 150 mA output-current capability. The device can sit between a video source and a downstream cable, monitor, or processing stage to reduce source-loading effects without adding an external feedback network. Its single-supply or ±5 V output-swing options support conventional video-interface design studies. The primary engineering benefit is a dedicated high-speed buffer function with predictable fixed gain, while the trade-off is the larger PDIP-8 footprint compared with modern surface-mount packages. Confirm the complete voltage, noise, slew-rate, and timing limits in the manufacturer datasheet before production release.
अनुशंसित
Communications Transmit Signal Path
OPA682P can buffer a communications signal before it enters a driver or downstream RF stage because its 240 MHz bandwidth preserves fast transitions and its 150 mA output-current capability provides greater drive than a conventional small-signal follower. The fixed +1 or −1 gain supports either non-inverting or inverting signal paths without external feedback resistors. Its 6 mA operating current is also suitable for power-conscious portable or distributed communication equipment. Designers should verify the exact output swing, supply range, load impedance, and stability requirements at the intended signal frequency because those values are not fully present in the supplied search excerpts.
अनुशंसित
High-Speed Test and Measurement
OPA682P fits source-isolation and level-buffer positions in high-speed test equipment where the measured system requires a 240 MHz buffer with low output impedance. The 150 mA output-current capability is useful when driving test cables, termination networks, or downstream instrumentation, while fixed +1 or −1 gain simplifies calibration references. Its 320 µA disabled state can reduce consumption when the test channel is inactive. The engineering trade-off is that fixed gain does not provide the flexible resistor-programmed attenuation of a general-purpose op-amp, so the system must be designed around the available gain configurations and verified operating limits.
अनुशंसित
Instrumentation Signal Conditioning
OPA682P is useful as a high-impedance-input, low-impedance-output interface in instrumentation signal chains where a sensor or frontend needs to drive a longer trace or measurement stage. Its 240 MHz bandwidth handles fast analog transitions, and the internally fixed +1 or −1 gain provides isolation without a discrete feedback network. The 6 mA supply current supports compact multi-channel systems, while the disable input permits individual channels to be turned down during idle periods. A complete review of input bias current, common-mode range, offset voltage, and noise is necessary because those specifications are unavailable in the supplied web excerpts.
अनुशंसित
Portable Signal-Chain Interface
OPA682P can serve as a low-power buffer in portable instrumentation or communication modules that require 240 MHz bandwidth without the higher current consumption of a large general-purpose amplifier. The normal supply current is 6 mA, and the disable function reduces it to 320 µA when the buffered path is not active. This makes controlled shutdown useful for battery-powered equipment and multi-channel systems. Fixed gain and the 8-pin PDIP footprint are the principal constraints for modern ultra-compact products; engineers should compare those mechanical and functional restrictions against surface-mount alternatives before choosing the through-hole configuration.
अनुशंसित
Analog Signal Isolation and Fanout
OPA682P can isolate a sensitive analog source from multiple downstream loads by presenting a high-impedance input and a stronger 150 mA-capable output. The 240 MHz bandwidth supports signal paths containing fast transients, and the fixed +1 or −1 gain lets the designer select amplitude preservation or polarity inversion without external feedback components. Its disable control can also be coordinated with system sequencing to hold downstream stages inactive during startup or test. Output stability, capacitive-load tolerance, and maximum input and output swing must be confirmed from the full manufacturer data before using the device with long cables or unusually capacitive loads.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा OPA682P — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद |
|---|---|
| Package | 8-pin PDIP |
| Brand | Texas Instruments |
| Amplifier Type | Wideband fixed-gain buffer amplifier |
| Number of Circuits | 1 circuit |
| Bandwidth | 240 MHz |
| Internally Fixed Gain | +1 or -1 |
| Supply Current | 6 mA |
| Disabled Supply Current | 320 µA |
| High Output Current | 150 mA |
| Output Voltage Swing | ±5 V or single-supply operation |
| Disable Function | Yes |
| Listed Starting Price as of 2026-10-29 | $1.3807 |
मुख्य विशेषताएँ
- Purpose-built high-speed fixed-gain buffering (बनामGeneral-purpose operational amplifier)
- Strong output-drive capability for a buffer (बनामConventional low-power voltage follower)
- Reduced consumption in the disabled state (बनामContinuously enabled general-purpose amplifier)
डिज़ाइन नोट्स
Route the OPA682P output directly to the intended load and minimize trace length, resistance, and capacitance between pins 1 and 8 when the configured gain requires those connections. High-speed signal paths should use a continuous ground reference and short supply connections. Keep sensitive sources physically separated from the output and disable-return traces to reduce parasitic coupling. The complete pin names and gain configuration must be confirmed from the manufacturer pinout before PCB routing.
Estimated normal-operation supply power is 6 mW per volt of supply voltage: 6 mA multiplied by the supply voltage. Thus, a 5 V rail consumes about 30 mW and a 12 V rail consumes about 72 mW. These are arithmetic estimates rather than datasheet power ratings. When the amplifier is disabled, the corresponding estimated consumption falls to 320 µW at 5 V or 3.84 mW at 12 V, subject to the actual disable conditions in the manufacturer data.
Do not treat the OPA682P as an interchangeable substitute for a general-purpose op-amp solely because both are eight-pin amplifiers. The OPA682P has internally fixed gain, specialized 240 MHz bandwidth, and a dedicated buffer architecture. Confirm the PDIP-8 pinout, supported supply range, input common-mode range, output swing, disable polarity, and stability into the intended load using the manufacturer datasheet before production use.
अनुपालन जानकारी
The supplied verified search results do not explicitly state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. AEC-Q100 is marked not applicable because the component is presented as a general-purpose catalog amplifier, not as an automotive-qualified variant.