PIC24F16KM104-E/ML - 32MHz 16-bit MCU | Microchip Technology
MPN: PIC24F16KM104-E/ML ✗ जीवन की समाप्तिPIC24F16KM104-E/ML अवलोकन
A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, working data memory, timers, communication peripherals, and I/O ports on one device. PIC24F devices belong to the 16-bit MCU -> microcontroller -> embedded semiconductor hierarchy and use a Harvard-style architecture suited to compact control systems. The PIC XLP designation identifies this family’s focus on low-power operation and compact embedded designs.
The PIC24F16KM104 integrates a 12-bit ADC, a DAC, and operational amplifiers according to the manufacturer product page. Its 5.5K x 24 Flash organization accommodates a 16-bit instruction architecture, while its 1 KB SRAM and 512-byte EEPROM support working state and nonvolatile parameter storage. The operating range of 1.8 V to 5.5 V allows the same device family to serve both 3 V and 5 V systems.
Programmable peripherals include flexible Capture/Compare/PWM modules and a Configurable Logic Cell, as described for the PIC24F family. These resources allow the MCU to measure timing inputs, generate PWM waveforms, and implement small amounts of hardware-assisted logic without requiring additional discrete components. The 44-QFN package reduces board area but requires careful escape routing and attention to the exposed thermal pad.
Typical uses include low-power sensor nodes, industrial condition-monitoring equipment, compact motor or actuator controllers, analog signal acquisition systems, and embedded products that need both digital control and on-chip ADC, DAC, or amplifier functions. The 16 KB Flash limit makes memory planning important when the application includes graphical interfaces, extensive protocol stacks, or large data buffers.
Designers should reserve decoupling capacitance at each supply pin, route the exposed pad as a thermal and electrical landing area, and verify signal compatibility at the lowest and highest intended supply voltage. Firmware, peripheral assignments, and pin multiplexing must be checked against the manufacturer pin-description table and device documentation before PCB release.
This product page consolidates the manufacturer specifications, lifecycle information, pin-compatible alternatives, application guidance, and practical design considerations needed to evaluate the PIC24F16KM104-E/ML for an embedded control design.
के लिए ड्रॉप-इन विकल्प PIC24F16KM104-E/ML — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं PIC24F16KM104-E/ML (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, ADC, Comparators, DAC, Operating Temperature.
PIC24F16KM104-I/ML
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →PIC24F16KM204-E/ML
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →PIC24F16KM204-I/ML
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →PIC24F16KM103-I/ML
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
PIC24F16KM102-I/ML
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →PIC24F16KM104-E/ML Maximum Ratings और Electrical Characteristics
| Product Type | 16-bit PIC XLP 24F microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Program Memory | 16 KB |
| Program Memory Organization | 5.5K x 24 words |
| RAM | 1 KB x 8 bits |
| EEPROM | 512 bytes |
| Operating Voltage Range | 1.8 V to 5.5 V |
| ADC Resolution | 12 bits |
| Integrated Analog Resources | ADC, DAC, and operational amplifiers |
| Timer Resource | Flexible Capture/Compare/PWM modules |
| Programmable Logic | Configurable Logic Cell |
| पैकेज | 44-QFN, 8 x 8 mm |
| माउंटिंग प्रकार | Surface mount |
| RoHS स्थिति | unknown |
| REACH Status | unknown |
PIC24F16KM104-E/ML 44-qfn, 8 x 8 mm पिन कॉन्फ़िगरेशन गाइड
PIC24F16KM104-E/ML (44-qfn, 8 x 8 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: PIC24F16KM104-E/ML.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
PIC24F16KM104-E/ML के लिए उपयुक्त है 6 अनुप्रयोगs: Low-Power Environmental Sensor Nodes, Industrial Condition Monitoring, Compact Motor and Actuator Control, Analog Signal Acquisition and Control, Battery-Powered Embedded Instruments, Programmable Logic and Timing Products.
Low-Power Environmental Sensor Nodes
The PIC24F16KM104-E/ML fits compact environmental sensors that acquire analog measurements, apply filtering, and transmit or store results. Its 12-bit ADC supports analog-to-digital conversion, while the 1.8 V to 5.5 V operating range permits use with both 3 V and 5 V system rails. The 1 KB RAM and 512-byte EEPROM provide limited working and configuration storage, so firmware should use buffering carefully and exploit the PIC24F family’s low-power operating features. The 44-QFN 8 x 8 mm package also reduces board area, although its exposed pad requires a compliant thermal-via layout.
अनुशंसित
Industrial Condition Monitoring
The PIC24F16KM104-E/ML can supervise pumps, motors, valves, or remote machinery when the design needs measurement, timing, and local control in one compact device. Its flexible Capture/Compare/PWM modules can support input timing, output compare, or PWM functions, and its integrated 12-bit ADC can read sensor signals without a separate converter. Operation from 1.8 V to 5.5 V supports industrial interface levels after appropriate signal conditioning. Firmware must remain within the 16 KB Flash limit, while the QFN thermal pad and exposed-pad layout must be treated as part of the mechanical and thermal design.
अनुशंसित
Compact Motor and Actuator Control
The PIC24F16KM104-E/ML is suitable for small motor, valve, or actuator controllers that combine position sensing with PWM generation. Flexible Capture/Compare/PWM peripherals can measure input edges and generate timed outputs, while the integrated ADC can read potentiometers, current sensors, or position transducers. Its 32 MHz maximum operating frequency gives the firmware more timing headroom than slower control loops, and the 1.8 V to 5.5 V range supports low-voltage systems. Designers should account for driver transistors, protection networks, and thermal rise because the MCU controls rather than directly supplies motor power.
अनुशंसित
Analog Signal Acquisition and Control
The PIC24F16KM104-E/ML can form the center of a compact analog control system because it combines a 12-bit ADC, DAC, and operational amplifiers with a 16-bit MCU core. The ADC can digitize sensor inputs, the DAC can generate an analog reference or test signal, and the amplifiers can support conditioning where their common-mode and output limits are acceptable. The MCU’s 5.5K x 24-word Flash organization, 1 KB RAM, and 512-byte EEPROM accommodate moderate algorithms rather than resource-intensive signal processing. Analog pin selection, acquisition timing, and output settling must be validated against the device electrical characteristics.
अनुशंसित
Battery-Powered Embedded Instruments
The PIC24F16KM104-E/ML can serve as the control core in a small battery-powered instrument that must mix measurement, logic, and power management. The PIC24F KM family is positioned around nanoWatt XLP low-power operation, and the MCU accepts 1.8 V to 5.5 V operation, allowing direct use with common low-energy rails. The 12-bit ADC reduces the need for a separate converter in suitable measurement chains. Battery life depends on firmware-selected sleep modes, peripheral activity, and analog biasing rather than CPU frequency alone. The small 8 x 8 mm QFN package also helps reduce board area in wearable or portable instruments.
अनुशंसित
Programmable Logic and Timing Products
The PIC24F16KM104-E/ML can implement small timing-sensitive products using its Configurable Logic Cell alongside flexible Capture/Compare/PWM peripherals. These hardware resources can handle input capture, output compare, PWM generation, and logic functions that would otherwise consume substantial microcontroller software capacity. The 32 MHz maximum CPU frequency supports supervisory algorithms and communications while dedicated peripherals manage time-critical events. Because the device has only 1 KB RAM and 16 KB Flash, partitioning real-time logic into peripherals is especially valuable. Board-level signal conditioning and timing-margin analysis remain necessary when the MCU controls external sensors, relays, or precision actuators.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा PIC24F16KM104-E/ML — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | PIC24F16KM104-I/ML | PIC24F16KM204-E/ML | PIC24F16KM204-I/ML | PIC24F16KM103-I/ML |
|---|---|---|---|---|---|
| Package | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Temperature-Grade Suffix | E | I | E | I | I |
मुख्य विशेषताएँ
- Identical base-device resources with a direct temperature-grade option (बनामPIC24F16KM104-I/ML)
- Higher-memory family option for expanded firmware (बनामPIC24F16KM204-E/ML)
- Integrated analog block reduces external component count (बनामPIC24F16KM103-I/ML)
डिज़ाइन नोट्स
Use the manufacturer’s 44-QFN 8 x 8 mm land pattern rather than selecting a footprint from pin count alone. The exposed thermal pad is a critical electrical and thermal feature; assign it to the appropriate ground net, provide the recommended thermal-via pattern, and maintain assembly keepouts. Place supply decoupling capacitors close to their associated pins to minimize loop area and high-frequency supply impedance.
Design the supply network for the full 1.8 V to 5.5 V operating range and verify every analog and digital peripheral at the intended rail. Because the device combines an ADC, DAC, and operational amplifiers with digital logic, analog and power-return routing should be arranged to limit coupling between conversion circuitry and switching nodes. Confirm peripheral current, external load, and pin limits against the manufacturer electrical-characteristics table before finalizing the power tree.
Do not treat a shared package suffix as proof of complete interchangeability. Verify Flash size, RAM, EEPROM, peripheral availability, pin multiplexing, interrupt mapping, programming configuration, and temperature grade for every replacement. In particular, moving from PIC24F16KM104-E/ML to a higher-memory KM device may preserve the footprint while changing linker requirements and peripheral behavior.
Estimated: the exposed-pad thermal path depends on the PCB copper area, via count, ambient temperature, and switching activity; therefore, no defensible junction-temperature rise can be calculated without those values. For new hardware, evaluate thermal performance using the manufacturer package data and the actual board stack-up. If the product will use the obsolete grade, include supply continuity and obsolescence risk in the production plan.
अनुपालन जानकारी
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact MPN during verification. The obsolete status was identified from the product listing; confirm lifecycle and sourcing status with Microchip before committing to production.
