THS6062ID - 100MHz Dual Differential Receiver | Texas Instruments
MPN: THS6062ID ✓ सक्रियTHS6062ID अवलोकन
A differential receiver is an interface-circuit block that extracts the difference between two input signals while rejecting common-mode voltage and noise. This function is important in communication systems where the wanted signal is small, transmission losses are significant, and unwanted voltage can be shared by both input lines. The THS6062 belongs to the high-speed voltage-feedback amplifier family and is used in interface IC, line-driver, receiver, and signal-conditioning applications.
Key characteristics include a 100 MHz -3 dB bandwidth, a typical 100 V/us slew rate, a typical 1.6 nV/sqrt(Hz) input-voltage noise density, and a typical 90 mA output drive. The receiver supports 5 V single-supply operation and dual supplies from -5 V to -15 V, giving designers flexibility for legacy telecom, ADSL, codec, and line-interface equipment. According to the Texas Instruments THS6062 product page, the circuit is stable at gains of 2 (-1) or greater.
The low-noise, high-speed architecture is useful where signal fidelity must be preserved across a broad bandwidth. The 100 MHz bandwidth supports high-data-rate communication paths, while the 100 V/us slew rate allows large-amplitude signals to be reproduced with limited slew-related distortion. The listed distortion figures include THD of -72 dBc at 1 MHz and -90 dBc at 1 MHz under the stated measurement conditions.
Typical applications include ADSL line-interface circuits, ADSL codec front ends, differential data receivers, communication equipment, and general high-speed signal-conditioning stages. The dual-channel configuration can process two related differential signals or be used in separate receiver channels when appropriate. Because this is a high-speed device, PCB layout, decoupling, return paths, input impedance, and output-load stability require careful attention.
When laying out a THS6062ID circuit, keep input and output traces short, provide local supply bypassing, maintain a continuous ground reference, and avoid long stubs or parasitic capacitance on high-impedance nodes. Confirm the intended gain, supply configuration, input common-mode range, output load, and termination against the manufacturer datasheet before releasing production artwork. This page combines verified manufacturer and distributor information with drop-in candidate review, application guidance, and design notes.
के लिए ड्रॉप-इन विकल्प THS6062ID — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
THS6062IDG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
THS6062CDG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8001
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LMH6629
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MAX4086
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
THS6062ID Maximum Ratings और Electrical Characteristics
| Product Type | Dual high-speed differential receiver |
| Number of Channels | 2 channels |
| Voltage-Feedback Bandwidth | 100 MHz (-3 dB) |
| Slew Rate | 100 V/us typical |
| Input Voltage Noise Density | 1.6 nV/sqrt(Hz) typical |
| Minimum Stable Gain | 2 (-1) or greater |
| Single-Supply Operation | 5 V |
| Dual-Supply Operation | -5 V to -15 V |
| Typical Output Drive | 90 mA |
| THD at 1 MHz | -72 dBc |
| ऑपरेटिंग तापमान रेंज | -40 C to +85 C |
| पैकेज | 8-SOIC (D), 0.154 inch (3.90 mm) width |
| पिन काउंट | 8 pins |
| माउंटिंग प्रकार | Surface mount |
| Application | ADSL data communication systems |
THS6062ID 8-soic (d), 0.154 inch (3.90 mm) width पिन कॉन्फ़िगरेशन गाइड
THS6062ID (8-soic (d), 0.154 inch (3.90 mm) width पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: THS6062ID.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
THS6062ID के लिए उपयुक्त है 6 अनुप्रयोगs: ADSL Line Receiver, ADSL Codec Front End, Differential Data Conditioning, Legacy Telecom Line Interface, High-Speed Instrumentation Front End, Mixed-Signal Communication Module.
ADSL Line Receiver
The THS6062ID fits an ADSL line receiver because Texas Instruments identifies it as a high-speed differential receiver for ADSL communication systems. Its 100 MHz -3 dB bandwidth provides substantial frequency range above the data-carrying signal, while the 100 V/us typical slew rate supports reproduction of larger-amplitude transitions with low timing distortion. The 1.6 nV/sqrt(Hz) typical input-voltage noise density is especially valuable when the receiver must preserve weak signals through analog stages. Place the receiver where the differential input lines remain short, controlled in impedance, and referenced to a continuous ground plane. Input termination and line-isolation components should be selected to preserve the full 100 MHz operating range, while supply bypassing should be located close to the device.
अनुशंसित
ADSL Codec Front End
The THS6062ID is suitable for the analog input stage ahead of an ADSL codec because the manufacturer states that its low noise and distortion performance exceed ADSL codec requirements. The dual receiver provides two channels for complementary or separate differential signals, while 100 MHz bandwidth and a 100 V/us slew rate provide ample margin for high-speed signaling stages. The verified 5 V single-supply option simplifies systems that cannot accommodate positive and negative rails, although the exact input common-mode range must be checked against the codec interface. Keep the codec connection short and use controlled impedance where transmission-line effects are significant. Power-supply bypass capacitors should be placed at the pins, with a quiet return path maintained through the analog and digital sections.
अनुशंसित
Differential Data Conditioning
The THS6062ID can condition differential signals in communication equipment because its voltage-feedback architecture provides 100 MHz bandwidth and stable operation at gains of 2 (-1) or greater. The verified 1.6 nV/sqrt(Hz) typical voltage-noise density supports low-noise amplification, while the 100 V/us slew rate supports signals with rapid amplitude changes. The device can also operate from -5 V to -15 V dual supplies, which is useful in legacy line-interface equipment with symmetrical rails. Differential routing must use matched geometry where timing skew would otherwise degrade the common-mode rejection benefit. Confirm termination, gain, output loading, and stability with the actual source and load because source impedance can materially affect high-speed closed-loop behavior.
अनुशंसित
Legacy Telecom Line Interface
The THS6062ID is appropriate for legacy telecom equipment that uses a 5 V single rail or a dual supply from -5 V to -15 V. Its 100 MHz voltage-feedback bandwidth allows the receiver to process high-speed line-interface signals, and the typical 90 mA output drive provides useful capability for moderate loading. Because the device was optimized for ADSL data communication rather than a general-purpose instrumentation amplifier, designers should verify gain, output swing, and stability in the intended topology. Maintain short feedback paths and place bypass capacitors close to the supply pins to reduce inductive supply noise. A solid ground reference is especially important because differential rejection cannot recover signal distortion already introduced by common impedance in the PCB.
अनुशंसित
High-Speed Instrumentation Front End
The THS6062ID can serve as a high-speed instrumentation front end when the source can be connected differentially and the circuit operates at gain 2 (-1) or greater. Its low 1.6 nV/sqrt(Hz) typical input noise and 100 MHz bandwidth make it useful for sensing small, rapidly changing differential quantities. Differential topology also helps reject common-mode voltage present on industrial or communication links. However, the supplied data does not define input bias current, input impedance, or common-mode limits, so those parameters must be checked before using it with high-impedance sensors. Keep sensor traces short, shield sensitive nodes from switching nodes, and terminate the source correctly. High-speed layout simulation and bench testing are recommended before treating the receiver as a precision measurement channel.
अनुशंसित
Mixed-Signal Communication Module
The THS6062ID supports mixed-signal communication modules that combine a sensitive receive path with digital control and data-processing functions. Its dual-channel architecture provides flexibility for two differential receiver paths, and the 100 MHz bandwidth allows placement before an ADC or codec without being the immediate bottleneck. The 5 V operating option can align with established communication-module rails, while the low-noise specification protects weak receive signals. Separation between the analog receiver and switching circuitry is essential: place the amplifier close to the source connector, route return currents continuously, and use dedicated return paths beneath high-current digital circuitry. Add local bulk and high-frequency bypass capacitance, and verify that the module's power-up sequence does not create input overstress on the receiver.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा THS6062ID — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | THS6062IDG4 | THS6062CDG4 | AD8001 | LMH6629 | MAX4086 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-SOIC (D) | 8-SOIC (D) | 8-SOIC (D) | 8-SOIC (D) | 8-SOIC (D) | 8-SOIC (D) |
| Product Type | Dual high-speed differential receiver | THS6062 family differential receiver | THS6062 family differential receiver | High-speed amplifier | High-speed amplifier | High-speed amplifier |
मुख्य विशेषताएँ
- Purpose-built ADSL receive positioning (बनामTHS6052ID)
- Verified high-speed and low-noise combination (बनामAD8001)
- Broad verified supply flexibility (बनामMAX4086)
डिज़ाइन नोट्स
Treat THS6062ID inputs and outputs as high-speed analog nets. Keep them short, avoid test pads and long branches, and use a continuous ground plane for return current. Differential pairs should use matched geometry when line length and skew materially affect signal integrity. Place the receiver close to the source connector or codec interface and keep switching-node copper away from sensitive input pins.
Provide local supply bypassing at the THS6062ID pins and preserve a low-impedance ground return. The verified device supports 5 V single-supply and -5 V to -15 V dual-supply configurations, so bypass values and layout should be selected for the exact operating rails. Before power-up, verify the input common-mode limits because a high-speed amplifier can be overstressed even when its supply rails remain within their nominal range.
Do not assume that an 8-SOIC alternative is automatically interchangeable. Check lead pitch, body dimensions, pin numbering, exposed-pad requirements, input and output functions, supply voltage, input common-mode range, stability gain, bandwidth, slew rate, and noise. In particular, confirm that the selected gain is 2 (-1) or greater as stated by Texas Instruments for the THS6062 and validate the actual source and load impedance.
Validate the complete channel with the intended source impedance, termination, cable or PCB loss, and output load. The verified 100 MHz bandwidth and 100 V/us slew rate establish device capability but do not guarantee acceptable system performance. Use scope measurements or simulation to inspect overshoot, ringing, settling, differential skew, and distortion, particularly when source impedance is high or the SOIC package's small pad geometry creates sensitivity to parasitic inductance.
अनुपालन जानकारी
The supplied verified data does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements. The IC is not described as an automotive-qualified AEC-Q100 device. Compliance declarations should be confirmed from the current manufacturer product documentation or distributor certificates.
