अंतिम बार खरीदने की सूचना: TJA1020T/N1 end-of-life के करीब है। अंतिम ऑर्डर तिथि: हमसे संपर्क करें. उपलब्ध वैकल्पिक पार्ट्स देखें →
NXP Semiconductors

TJA1020T/N1 - LIN Transceiver, 8-SO | NXP Semiconductors

MPN: TJA1020T/N1 ✗ जीवन की समाप्ति
8-pin SO package Package
न्यूनतम ऑर्डर मात्रा: 1 |

TJA1020T/N1 अवलोकन

The NXP Semiconductors TJA1020T/N1 is a single LIN-bus transceiver integrated circuit packaged in an 8-pin SO package. It provides the physical-layer interface between a LIN network and a host microcontroller, converting serial data into the LIN bus signal and delivering received bus data through the RXD output. The TJA1020T/N1 is listed as a half LINbus transceiver, indicating its role as a node interface for LIN communication networks.

A LIN transceiver is a mixed-signal interface device within the broader hierarchy of interface ICs, communication transceivers, and semiconductors. LIN, or Local Interconnect Network, is used for low-cost distributed control in vehicle and industrial networks. The transceiver provides the physical signaling layer between a microcontroller's serial interface and the wired LIN bus, while protocol handling, diagnostics, and higher-layer message handling remain the responsibility of the host controller.

The principal product-specific features visible in the manufacturer and distributor documentation are the 8-pin SO package, LIN transceiver function, half-LINbus node role, RXD receive path, TXD transmit input, LIN bus connection, internal bus-output pull-up arrangement, and support for leader-side implementation using external components. The manufacturer describes the LIN output as being pulled high through an internal termination resistor, while a leader design can add a resistor-and-diode network between the LIN pin and a supply-related pin.

Operationally, the transmit input accepts the controller's serial waveform and the device converts it into a LIN-compatible bus waveform. In the receive direction, the receiver detects the LIN bus input and transfers the recovered data to the host through RXD. The interface therefore isolates the controller from direct physical signaling while supporting bidirectional communication over a single LIN conductor relative to the vehicle ground reference.

Typical uses include LIN-controlled automotive sub-networks, body electronics modules, seat and door modules, climate-control peripherals, sensor interfaces, actuator controllers, and industrial distributed-control nodes. The part is especially relevant when an existing microcontroller already implements the LIN protocol and requires a dedicated physical-layer transceiver. Its 8-pin SO package also supports compact, conventional PCB layouts where an 8-pin surface-mount footprint is available.

Design attention should center on the LIN bus network, grounding, transceiver supply arrangement, and the distinction between follower and leader implementations. Follower nodes use the internal pull-up behavior described by NXP, whereas leader nodes require the appropriate external resistor and diode network. PCB traces should preserve a short, direct path to the LIN connector and maintain a continuous ground reference. The manufacturer product page should be consulted for the exact application circuit, recommended external components, and supply requirements.

This page consolidates the exact package and lifecycle information, source datasheet links, interface-focused design guidance, and documented substitution information for engineers evaluating the TJA1020T/N1. Because the manufacturer marks the product as end-of-life, engineers should also plan a migration path or confirm availability through the Request a Quote form before committing to a new production design.

के लिए ड्रॉप-इन विकल्प TJA1020T/N1 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

TJA1021T/3

✅ ड्रॉप-इन
📦 SOIC-8
Improved ESD specification and optimized slew rate and wave shaping versus TJA1020; published information identifies pin-to-pin compatibility.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TJA1020T/N1,118

✅ ड्रॉप-इन
📦 SOIC-8
Same TJA1020T electrical device and 8-pin SO footprint; final code differs by packing configuration, with no stated functional difference.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TJA1020T/N/S490,11

✅ ड्रॉप-इन
📦 SOIC-8
Same TJA1020T function and 8-pin SO footprint; ordering code differs by packing configuration, with no stated electrical change.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TJA1020T/N1 विशेषताएं

Product Type LIN bus transceiver
Bus Category LINbus serial interface
Transceiver Role Half LINbus transceiver
Manufacturer NXP Semiconductors
पैकेज 8-pin SO package
Package Type SOIC-8 surface-mount package
पिन की संख्या 8 pins
लाइफसाइकिल स्थिति End of Life
Receive Output RXD digital data output
Transmit Input TXD serial data input
Bus Connection LIN bus input and output
LIN Output Pull-Up Internal termination resistor pulls LIN bus output high
Leader Implementation External resistor in series with a diode between LIN and INH or BAT

TJA1020T/N1 पिन कॉन्फ़िगरेशन

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
पिन 1 RXD — Received data output to the host microcontroller
पिन 2 GND — Ground connection
पिन 3 BAT — Battery supply input
पिन 4 TXD — Transmit data input from the host controller
पिन 5 LIN — LIN bus input and output
पिन 6 GND — Ground connection
पिन 7 INH — Inhibit input
पिन 8 VCC — Logic supply input

सामान्य अनुप्रयोग

TJA1020T/N1 के लिए उपयुक्त है 6 अनुप्रयोगs: Automotive LIN Body-Control Nodes, Vehicle Door and Seat Modules, Climate-Control Peripheral Interfaces, Industrial Distributed-Control Networks, Automotive Sensor Node Interfaces, Legacy LIN Controller Maintenance.

🚗

Automotive LIN Body-Control Nodes

The TJA1020T/N1 fits distributed body-control modules that need a dedicated LIN physical-layer interface in an 8-pin SO package. A host microcontroller handles message formatting, timing, diagnostics, and application logic, while the transceiver converts TXD commands into a LIN bus waveform and returns received data through RXD. This division keeps bus-drive and receive functions outside the controller. Because NXP identifies the device as End of Life, engineers should evaluate a current successor for new vehicle platforms while retaining this part only where an existing design is being maintained. LIN wiring, ground continuity, and the correct leader or follower network remain the principal implementation considerations.

🚗

Vehicle Door and Seat Modules

Door locks, window switches, seat controls, and related comfort modules commonly use LIN sub-networks to reduce wiring while coordinating a limited set of commands and sensor inputs. The TJA1020T/N1 provides the communication boundary between the module controller and that sub-network through TXD, RXD, and the LIN connection. Its 8-pin SO format is compatible with conventional compact PCB layouts. The host processor remains responsible for debouncing, diagnostic responses, and safety-related control decisions. For a follower node, the implementation can use the documented internal bus pull-up; a leader design requires the external resistor-and-diode arrangement described by NXP.

🏭

Climate-Control Peripheral Interfaces

Climate-control systems can use LIN-connected modules for fan control, temperature sensing, flap positioning, and panel interactions. The TJA1020T/N1 is appropriate when a microcontroller already generates the LIN protocol frame and requires a physical-layer transceiver in an 8-pin package. TXD carries the controller's serialized command signal into the transceiver, and RXD presents the recovered bus signal to the processor. The compact interface supports economical sub-network wiring, although PCB layout must preserve the bus reference to ground and minimize the distance between the transceiver and the bus connection. New designs should confirm lifecycle continuity before committing to the End-of-Life device.

🏭

Industrial Distributed-Control Networks

The TJA1020T/N1 can also serve as the physical-layer interface in small industrial LIN networks used for local actuator and sensor subsystems. The component is useful when a controller already supports LIN framing but requires a dedicated bus transceiver with separate TXD and RXD paths. This arrangement simplifies firmware ownership while providing a defined interface between digital control logic and the wired bus. The NXP application information supports both follower and leader configurations, with the leader requiring an external pull-up network. Engineers must verify supply limits, ESD requirements, temperature range, and EMC performance against the manufacturer's datasheet before using the part outside its intended environmental envelope.

🚗

Automotive Sensor Node Interfaces

A LIN sensor node can use the TJA1020T/N1 to connect a local sensing or conditioning circuit to a vehicle controller. The sensor or actuator module processes its local signal and communicates through a host microcontroller, while the transceiver manages the physical LIN waveform and receive path. This architecture avoids implementing bus-drive, receive, and waveform-shaping functions in the controller. The 8-pin SO package supports compact module layouts, and the documented RXD and TXD interface keeps software integration straightforward. For production, engineers should confirm the exact device status, EMC expectations, bus termination method, and protection requirements in the NXP documentation.

🔧

Legacy LIN Controller Maintenance

The TJA1020T/N1 is directly relevant to repair and continuation platforms built around the original TJA1020 communication architecture. Its documented TXD input, RXD output, and LIN physical connection allow a replacement PCB to preserve the established host-controller interface. This is especially useful when replacing aged assemblies in industrial equipment or vehicle electronics without redesigning the surrounding firmware. Engineers should compare each ordered suffix carefully, verify the 8-pin footprint, and reproduce the original leader or follower external network. Because the manufacturer marks the product as End of Life, sourcing confirmation and traceability are essential for long-term maintenance programs.

अनुशंसित उत्पादों का सारांश

What is the TJA1020T/N1?
The TJA1020T/N1 is an NXP Semiconductors LIN transceiver used to connect a microcontroller to a LINbus network through an 8-pin SO package. According to the NXP TJA1020 product information, the receiver detects data at the LIN input and transfers it to the microcontroller through RXD, while the TXD input accepts the controller's transmit data. The part is listed as a half LINbus transceiver and is marked End of Life by the manufacturer.
TJA1020T datasheet
The official TJA1020T datasheet is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1020.pdf. It is the authoritative document for the device's pin functions, electrical characteristics, application information, and recommended external circuitry. NXP also maintains a product-information page at https://www.nxp.com/part/TJA1020T, where the part is identified as End of Life and links to lifecycle and purchasing information.
NXP TJA1020T
NXP's TJA1020T is a LIN physical-layer transceiver for distributed automotive or industrial control networks, and the TJA1020T/N1 ordering variant is supplied in an 8-pin SO package. The NXP product page states that the LIN output is pulled high by an internal termination resistor and that the RXD output transfers recovered bus data to the microcontroller. Use the manufacturer datasheet for electrical limits and the product page for lifecycle status.
What is the operating voltage range of the TJA1020T/N1?
The TJA1020T/N1 operating and supply voltage limits must be taken from the NXP TJA1020 datasheet because the accessible product summary does not state numerical values. The device includes BAT, INH, VCC, and GND-related connections in its application architecture, but their exact minimum and maximum ratings should not be inferred from the package description. Confirm the recommended battery and logic ranges against the manufacturer's electrical-characteristics table before designing the supply network.
Where can I find the TJA1020T/N1 pinout?
The TJA1020T/N1 pin assignment is documented in the official NXP TJA1020 datasheet at https://www.nxp.com/docs/en/data-sheet/TJA1020.pdf. The device uses an 8-pin SO package, and its interface includes RXD, TXD, LIN, battery-related supply, logic supply, ground, and inhibit-related functions. Use the pin-description table and application diagram when assigning PCB nets rather than relying only on package orientation.
How does the TJA1020T/N1 communicate with a microcontroller?
The TJA1020T/N1 uses TXD for the controller's serial transmit input and RXD for the recovered receive-data output. According to the NXP product information, the receiver detects the data stream at the LIN bus input and transfers it to the microcontroller through RXD. In the transmit direction, the transceiver converts the controller's TXD waveform into the physical LIN bus signal.
What is the difference between a LIN follower and a leader?
A LIN follower relies on the transceiver's internal bus-output pull-up, whereas a LIN leader requires an external resistor-and-diode network to pull the bus high. The NXP product information specifically states that the LIN output is pulled high through an internal termination resistor and recommends an external resistor in series with a diode between the LIN pin and INH or BAT for a leader application.
Is the TJA1020T/N1 suitable for automotive body electronics?
The TJA1020T/N1 is functionally suited to LIN-based body electronics because it implements the physical-layer interface for a half LINbus node in an 8-pin SO package. However, automotive qualification status and the numerical operating limits must be checked in the manufacturer datasheet before release. The NXP product page identifies the device as End of Life, so new automotive programs should evaluate a supported successor as well as the TJA1020.
TJA1020T/N1 vs TJA1021T/3 - which is better?
The TJA1021T/3 is the stronger choice for a new design when its supported lifecycle status and detailed electrical ratings meet the project requirements. Published comparison information describes the TJA1021 as pin-to-pin compatible with the TJA1020 and notes improved ESD specifications plus optimized slew-rate and wave-shaping behavior for lower electromagnetic emission. The exact MPN, package, and production status should be confirmed with NXP before substitution.
When should I choose the TJA1020T/N1 instead of TJA1021T/3?
Choose the TJA1020T/N1 only when maintaining an existing qualified design is more important than obtaining a newer lifecycle option or improved transient and emission characteristics. The TJA1021 family is reported as pin-to-pin compatible with the TJA1020 and offers improved ESD and optimized wave-shaping behavior. For new production, compare those functional improvements against availability and all application-level electrical requirements.
What can replace the TJA1020T/N1?
The TJA1021T/3 is the closest documented replacement because published comparison information identifies it as pin-to-pin compatible with the TJA1020. It also offers improved ESD specifications and optimized slew-rate and wave-shaping behavior intended to minimize electromagnetic emission. Because the TJA1020T/N1 is End of Life, request the current NXP lifecycle position and quotation through the Request a Quote form on this page.
Is TJA1020T/N1 the same as TJA1020T/N1,118?
TJA1020T/N1 and TJA1020T/N1,118 denote ordering variants of the same TJA1020T device family, but the final suffix commonly identifies the specific reel or packing configuration. They should not be treated as different functional transceivers solely because their ordering codes differ. Confirm the suffix, package form, quantity, and production requirements on the manufacturer's product page before consolidating them for procurement.
Where to buy the TJA1020T/N1 online?
Use the Request a Quote form on this page to request the NXP TJA1020T/N1, confirm the exact suffix and package, and obtain current availability, lead time, and commercial terms. The manufacturer identifies the TJA1020T as End of Life, so a quote should include confirmation of remaining supply and any authorized sourcing route. Avoid starting a new production allocation until the source and lifecycle plan are documented.
What is the price of the TJA1020T/N1?
Current commercial pricing for the TJA1020T/N1 should be obtained through the Request a Quote form on this page because the part is End of Life and its commercial availability may change. The request should identify TJA1020T/N1, the required packing suffix, and annual and prototype quantities. This allows the quote to reflect the correct configuration and a confirmed supply channel.
What is the lead time for the TJA1020T/N1?
The current lead time for the TJA1020T/N1 must be confirmed through the Request a Quote form on this page. NXP marks the TJA1020T as End of Life, so lead time depends on remaining factory supply, the selected ordering suffix, and the requested quantities. For production planning, ask the supplier to confirm quantity, traceable origin, and the latest shipment schedule in writing.

के लिए इंजीनियरिंग संदर्भ डेटा TJA1020T/N1 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the TJA1020T/N1 when maintaining an existing TJA1020-based design is necessary, particularly if the original 8-pin SO footprint, TXD/RXD interface, and follower or leader wiring are already established. The part is identified as End of Life, so new designs should first assess lifecycle continuity. The TJA1021T/3 is the preferred same-manufacturer migration candidate because it is reported as pin-to-pin compatible and offers improved ESD characteristics plus optimized slew-rate and wave-shaping behavior for lower electromagnetic emission. The TJA1020T/N1,118 and TJA1020T/N/S490,11 variants retain the original electrical function but differ in ordering or packing configuration, so compare suffix and packaging requirements carefully. For any migration, verify supply voltage, logic thresholds, timing, temperature, ESD, EMC behavior, and leader or follower external components against the official datasheets before releasing production artwork.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद TJA1021T/3 TJA1020T/N1,118 TJA1020T/N/S490,11
Package 8-pin SO package 8-pin SO package 8-pin SO package 8-pin SO package
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Device Type LIN transceiver LIN transceiver LIN transceiver LIN transceiver
Bus Role Half LINbus transceiver LIN transceiver Half LINbus transceiver Half LINbus transceiver
Transmit Interface TXD input TXD input TXD input TXD input
Receive Interface RXD output RXD output RXD output RXD output
Waveform Behavior LIN physical-layer transmission and reception Optimized slew rate and wave shaping LIN physical-layer transmission and reception LIN physical-layer transmission and reception

मुख्य विशेषताएँ

  • Documented pin-to-pin migration within the NXP LIN transceiver family (बनामTJA1021T/3)
  • Improved transient robustness in the newer family member (बनामTJA1021T/3)
  • Optimized physical-layer waveform behavior (बनामTJA1021T/3)

डिज़ाइन नोट्स

Assign the PCB footprint from the exact TJA1020T/N1 orderable drawing and verify pin 1 orientation against the 8-pin SO package. Keep the LIN connection short and place any required leader-mode resistor-and-diode network close to the transceiver. Maintain a low-impedance ground reference beneath the device and toward the LIN connector so that bus currents have a compact return path.

Do not automatically configure the LIN pull-up network as if every node were a leader. NXP states that the LIN output is pulled high by an internal termination resistor and that a leader uses an external resistor in series with a diode between LIN and INH or BAT. Reproduce the original network architecture and verify it against the manufacturer's application diagram for each node type.

The BAT, VCC, INH, and ground connections must be designed around the electrical limits in the official NXP datasheet. Route supply and ground pins directly to their associated decoupling and return paths, and avoid sharing narrow return segments with unrelated switching currents. Check the controller's TXD and RXD levels against the device's logic thresholds before production release.

The LIN bus is a single-wire network whose signal quality depends on stable termination, ground continuity, and control of edge rates. Compare the TJA1020 with the TJA1021T/3 when electromagnetic-emission margin is critical because published comparison information describes optimized slew-rate and wave-shaping behavior in the TJA1021. Final EMC performance still depends on the complete vehicle or industrial harness and connector implementation.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The accessible NXP product summary identifies the TJA1020T as End of Life but does not state the numerical environmental, substance, or automotive-qualification attributes.

डेटा सत्यापन तिथि: 2026-11-14 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

tja1020t datasheet nxp tja1020t TJA1020T/N1 datasheet pdf TJA1020T/N1 pinout TJA1020T/N1 equivalent TJA1020T/N1 replacement TJA1020T/N1 vs TJA1021T/3 TJA1020T/N1 price TJA1020T/N1 stock TJA1020T/N1 application circuit

संबंधित कंपोनेंट्स और शब्द

NXP Semiconductors TJA1020T/N1 TJA1020T TJA1021T/3 LIN transceiver LIN bus Local Interconnect Network interface IC communication transceiver semiconductor TXD RXD INH BAT VCC LIN bus termination resistor leader node follower node 8-pin SO package SOIC-8 package surface-mount package microcontroller automotive body electronics industrial distributed control electromagnetic emission
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें