Sirkuit Terpadu

Subkategori

📁 ADC/DAC 3.100+ produk 📁 IC Penguat 1.800+ produk 📁 Codec Audio 18 produk 📁 IC Audio 2 produk 📁 Jam & Pewaktuan 650+ produk 📁 Comparator ICs 1 produk 📁 DSP 1.100+ produk 📁 IC Akuisisi Data 2 produk 📁 Potensiometer Digital 4 produk 📁 Driver & Pengendali Display 1 produk 📁 FPGA & CPLD 7.100+ produk 📁 IC Antarmuka 3.100+ produk 📁 Driver LED 1 produk 📁 IC Logika 450+ produk 📁 IC Memori 870+ produk 📁 Mikrokontroler 20.000+ produk 📁 Mikroprosesor 4 produk 📁 Driver Motor 1 produk 📁 Lainnya 1 produk 📁 Antarmuka Sensor dan Detektor 1 produk 📁 IC Khusus 15 produk 📁 IC Video 14 produk

Produk (38.000+)

TLV9061IDCKR - 10MHz RRIO CMOS Op Amp SC-70-5 | TI
TLV9061IDCKR

TLV9061IDCKR - 10MHz RRIO CMOS Op Amp SC-70-5 | TI

The Texas Instruments TLV9061IDCKR is a single-channel, 10-MHz unity-gain-bandwidth, rail-to-rail input/output (RRIO) CMOS operational amplifier in a 5-pin SOT-SC70 (DCK) package. It operates from a 1.8 V to 5.5 V single supply, delivers 538 µA quiescent current, and offers ±0.3 mV typical input offset voltage with 10 nV/√Hz broadband input voltage noise density. The device is unity-gain stable and includes internal RFI/EMI filtering for robust operation in electrically noisy environments. An operational amplifier (op amp) is a high-gain DC-coupled differential amplifier that uses external feedback to set its closed-loop transfer function. Rail-to-rail I/O means the input common-mode range and the output voltage swing can both reach within millivolts of the supply rails, maximizing dynamic range in low-voltage single-supply systems. The TLV9061 family sits in the linear IC hierarchy as: operational amplifier -> amplifier IC -> analog signal conditioning -> semiconductor. Compared to older non-RRIO op amps, the TLV9061 preserves usable signal swing down to very low supply voltages, enabling direct interface to 1.8 V MCUs and sensors. Key features include 10 MHz gain-bandwidth product, 6.5 V/µs slew rate, 0.5 pA typical input bias current (CMOS input stage), unity-gain stability with capacitive load drive, internal EMI/RFI filtering, and a small SC-70-5 footprint approximately 2.0 mm × 1.25 mm. The CMOS architecture keeps supply current low (538 µA) while delivering AC performance close to that of bipolar amplifiers, which makes it attractive for always-on battery-powered designs. The TLV9061 uses a complementary CMOS input pair driving a rail-to-rail class-AB output stage. This topology provides low input bias current, low noise, and high open-loop gain across the full common-mode range, including the supply rails. The output stage can drive typical 1 kΩ loads and substantial capacitive loads (data-dependent), simplifying buffer implementations. Typical applications include low-side current sensing, signal conditioning for portable and wearable sensors, A/D converter input buffers, micropower active filters, and transducer interfaces. Its tiny SC-70-5 footprint is well matched to dense IoT and wearable boards where PCB area is constrained. When designing with this device, place a 0.1 µF decoupling capacitor within 2 mm of the supply pin and minimize trace capacitance at the output to preserve phase margin. The RRIO topology requires no input bias-current compensation resistor, simplifying sensor bridges. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including a parametric comparison against competing low-voltage CMOS op amps from the same product family.

Permintaan RFG Kontak
TLV9064SIRTER - Quad 10MHz RRIO Op Amp w/ Shutdown | TI
TLV9064SIRTER

TLV9064SIRTER - Quad 10MHz RRIO Op Amp w/ Shutdown | TI

The Texas Instruments TLV9064SIRTER is a quad-channel, 10-MHz unity-gain stable CMOS operational amplifier with rail-to-rail input and output (RRIO) capability, housed in a 16-pin WQFN (RTE) package with 3 mm x 3 mm footprint. Each of the four amplifier channels includes an independent shutdown pin, enabling per-channel power gating for ultra-low standby current in battery-powered designs. The device operates from a 1.8 V to 5.5 V single supply. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output, used as a fundamental building block in analog signal conditioning. The TLV9064 belongs to the broader category of CMOS op amps (using CMOS input stages for low bias current) and the rail-to-rail family, which can swing its output to within millivolts of both supply rails. This category sits within the integrated circuits hierarchy: op amp -> amplifier IC -> analog IC -> semiconductor IC -> electronic component. Key specifications include a unity-gain bandwidth of 10 MHz, low input offset voltage of ±0.3 mV (typical), broadband input voltage noise of 10 nV/√Hz, input bias current of 0.5 pA, and quiescent current of 538 µA per channel. The amplifier is unity-gain stable, capable of driving large capacitive loads, and incorporates internal RFI/EMI rejection filtering for robust operation in noisy environments. The TLV9064 uses a CMOS process enabling rail-to-rail input common-mode range and rail-to-rail output swing. Shutdown logic is implemented per-channel, allowing unused channels to be placed in a high-impedance low-Iq state. According to the manufacturer datasheet, internal RFI filters suppress AM-band interference without external components, simplifying PCB layout in cost-sensitive applications. Typical applications include signal conditioning in cost-sensitive consumer IoT sensors, low-side current sensing in battery chargers, active filtering in audio front-end paths, photodiode transimpedance stages, and ADC driver / buffer circuits for portable instrumentation. The wide supply range and shutdown feature also make it suitable for always-on industrial sensor interfaces. When designing with this device, ensure stable operation by following the datasheet recommended feedback network for unity-gain stability, especially when driving large capacitive loads. Per-channel shutdown pins should be tied to VCC through a pull-up if shutdown is unused, otherwise the input may float and place the channel in an undefined state.

Permintaan RFG Kontak
TLV9152IDBVR - Dual 16V 4.5MHz Low-Power Op Amp | TI
TLV9152IDBVR

TLV9152IDBVR - Dual 16V 4.5MHz Low-Power Op Amp | TI

The TLV9152IDBVR is a dual, 16-V, 4.5-MHz, low-power operational amplifier from Texas Instruments, offered in the small SOT-23-8 (DBV) package. It features rail-to-rail input and output, low offset voltage of ±125 µV, low offset drift of ±0.3 µV/°C, and low noise of 10.5 nV/√Hz at 1 kHz. With a wide bandwidth of 4.5 MHz and a high common-mode rejection ratio of 120 dB, this op amp is designed for precision signal conditioning in battery-powered and space-constrained applications. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, used in analog signal processing circuits such as amplifiers, filters, and buffers. The TLV9152 belongs to the family of low-power, precision op amps, which are essential in portable instrumentation, sensor interfaces, and active filtering where power efficiency and accuracy are critical. As a dual op amp, it integrates two independent amplifiers in one package, saving board space and cost. Key features of the TLV9152 include a supply voltage range of 2.7 V to 16 V, a quiescent current of 0.65 mA per channel, and an output current capability of 75 mA. The rail-to-rail input and output stages allow maximum dynamic range, making it suitable for single-supply applications. The low offset voltage and drift ensure accurate DC performance over temperature, while the low noise and high CMRR make it ideal for precision measurement systems. Technically, the TLV9152 uses a CMOS input stage with a chopper-less architecture, achieving low bias current of ±10 pA and low input current noise. The device is fully specified over the extended industrial temperature range of -40°C to +125°C. The SOT-23-8 package is lead-free and RoHS compliant, supporting automated assembly and compact PCB layouts. Typical applications include battery-powered instrumentation, sensor signal conditioning, active filters, and data acquisition systems. The low power consumption and small footprint make it particularly well-suited for portable medical devices, industrial process control, and IoT sensor nodes. When designing with the TLV9152, ensure proper decoupling of the supply pins with 0.1 µF ceramic capacitors placed close to the device. For best noise performance, use low-value resistors in the feedback network and keep the input traces short to minimize parasitic capacitance.

Permintaan RFG Kontak
TLV9152IDGKR - Dual 16V 4.5MHz Low-Power Op Amp | TI
TLV9152IDGKR

TLV9152IDGKR - Dual 16V 4.5MHz Low-Power Op Amp | TI

The TLV9152IDGKR is a dual, 16-V, 4.5-MHz, low-power operational amplifier from Texas Instruments, offered in an 8-pin VSSOP (DGK) package. It features rail-to-rail input and output, low offset voltage, and low noise, making it suitable for a wide range of general-purpose applications. The device operates over a supply range of 2.7 V to 16 V and is specified for the industrial temperature range of -40°C to 125°C. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and amplification. Op amps are categorized within the broader hierarchy of linear integrated circuits, which also includes comparators, voltage regulators, and instrumentation amplifiers. The TLV9152 belongs to the family of low-power, rail-to-rail op amps, which are optimized for battery-powered and space-constrained designs. Key features of the TLV9152 include a gain-bandwidth product of 4.5 MHz, a slew rate of 2.5 V/µs, and a low quiescent current of 550 µA per channel. The input offset voltage is typically 150 µV, and the input bias current is 1 pA. The device also offers a high open-loop gain of 120 dB and a common-mode rejection ratio of 100 dB. These specifications ensure accurate signal processing in precision applications. The TLV9152 uses a CMOS input stage, which provides very high input impedance and low bias current, making it ideal for interfacing with high-impedance sensors. The rail-to-rail input and output capability allows the amplifier to operate with the full supply range, maximizing dynamic range in single-supply systems. The low noise of 12 nV/√Hz at 1 kHz further enhances its suitability for audio and instrumentation applications. Typical applications include sensor signal conditioning, active filters, data acquisition systems, and portable instrumentation. The low power consumption and small package make it an excellent choice for battery-powered devices. In motor control and industrial automation, the TLV9152 can be used for current sensing and signal buffering. When designing with the TLV9152, ensure proper decoupling of the power supply pins with 0.1 µF ceramic capacitors placed close to the device. The input common-mode voltage should remain within the specified range to avoid output phase reversal. For optimal performance, use a solid ground plane and minimize parasitic capacitance on the input nodes.

Permintaan RFG Kontak
TLV9301IDBVR - 40V 1MHz RRO Op Amp SOT-23-5 | Texas Instruments
TLV9301IDBVR

TLV9301IDBVR - 40V 1MHz RRO Op Amp SOT-23-5 | Texas Instruments

The Texas Instruments TLV9301IDBVR is a single-channel, 40-V, 1-MHz, rail-to-rail output (RRO) operational amplifier optimized for cost-sensitive systems and offered in a 5-pin SOT-23 (DBV) package. It belongs to the TLV930x family (TLV9301 single, TLV9302 dual, TLV9304 quad) and delivers ±0.5 mV typical input offset voltage, ±2 µV/°C typical offset drift, and 1-MHz gain bandwidth with rail-to-rail output swing for maximum dynamic range on low-voltage rails. An operational amplifier (op amp) is a high-gain DC-coupled differential amplifier that uses external feedback components to set closed-loop behavior. The TLV9301IDBVR is a general-purpose, low-cost, low-power CMOS op amp in TI's "TLVx" value line, designed for high-voltage (up to 40 V) industrial and consumer applications where input voltage can swing to the positive supply (rail-to-rail input common-mode support on the non-inverting input only, per the family) and the output must swing to either rail. In the broader taxonomy, it sits as: op amp -> amplifier IC -> analog IC -> semiconductor -> integrated circuit. Key differentiating specs include a wide 2.7-V to 40-V single-supply operating range (or ±1.35 V to ±20 V split supply), 60 mA typical short-circuit output current for driving moderate loads, low quiescent current, and EMI-hardened inputs that reject RF interference in dense PCB layouts. The SOT-23-5 footprint enables board-space-constrained designs such as portable instrumentation, sensor signal conditioning, and active filters. Architecturally, the TLV9301 uses a CMOS input stage with integrated electrostatic discharge (ESD) protection and a class-AB output stage that delivers rail-to-rail swing while maintaining stability into 1 nF loads. Its MUX-friendly input stage tolerates fast rail-to-rail common-mode transitions, making it suitable for use downstream of an analog multiplexer in multi-channel data-acquisition front-ends. Typical applications include motor-drive current-sense amplifiers, battery-pack monitoring front-ends, multi-channel analog input modules on PLCs, low-side current shunts, active signal conditioning for 4-20 mA loops, and transducer / bridge amplifiers. Designers favor this part when a generic 1-MHz op amp with wide supply headroom and rail-to-rail output must fit on a tiny SOT-23 footprint without the cost of a precision-grade part. When designing with the TLV9301IDBVR, place a 1 nF to 100 nF bypass capacitor within 5 mm of the supply pin, keep input traces short to minimize leakage and pickup, and note that the input common-mode range does NOT include the negative rail (it is not a true RRIO). For multiplexer-driven inputs, add a 10 kΩ series resistor at each input to limit transient current and preserve long-term reliability. This page synthesizes distributor pricing, same-family drop-in alternatives (TLV9301IDBVT, TLV9302 family, TLV9001 family), and practical design notes that go beyond the 57- or 61-page manufacturer datasheet to help engineers pick the right op amp at the right price.

Permintaan RFG Kontak
TLV9352IDR - Dual 40V 3.5MHz RRO Op Amp | Texas Instruments
TLV9352IDR

TLV9352IDR - Dual 40V 3.5MHz RRO Op Amp | Texas Instruments

The Texas Instruments TLV9352IDR is a dual, 40-V, 3.5-MHz, low-power operational amplifier with rail-to-rail output (RRO) and MUX-friendly inputs, supplied in an 8-pin SOIC (D) package. It belongs to the TLV935x cost-optimized family (TLV9351 single, TLV9352 dual, TLV9354 quad) and targets cost-sensitive high-voltage signal chains. Key headline parameters: 40-V supply capability, 3.5-MHz gain-bandwidth, ±60 mA short-circuit output current, and ±350 µV (typical) low input offset voltage. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. Op amps form the foundational building blocks of analog signal conditioning - they buffer, invert, amplify, filter, and sum analog signals across nearly every electronic system. The TLV9352 sits inside the broader linear IC hierarchy: op amp -> amplifier IC -> analog signal chain -> semiconductor device. Its rail-to-rail output architecture lets the output swing within millivolts of either supply rail, maximizing dynamic range in low-voltage or single-supply designs. Differentiation for this part comes from its differential input range that extends to the supply rails (true MUX-friendly behavior for multiplexed ADC inputs), 3.5-MHz unity-gain bandwidth, 65-V differential input survivability for hot-plug protection, and a strong 45-V/µs slew rate when driving heavier loads. Low offset drift of ±1.5 µV/°C keeps DC accuracy stable over -40 °C to +125 °C operation. The wide 4.5 V to 40 V supply range (or ±2.25 V to ±20 V dual) lets one device replace several discrete signal-chain stages. Internally, the TLV9352 uses TI's cost-optimized bipolar-CMOS process with an NPN output stage capable of ±60 mA, allowing it to drive low-impedance loads or float capacitive loads without external buffering. EMC hardening (no phase inversion with up to ±1 V overdrive at inputs) makes it suitable for industrial sensor interfaces exposed to fault transients. Typical applications include multi-channel data-acquisition front-ends, high-voltage buffer amplifiers driving SAR ADCs, industrial current and voltage sensing, motor-position feedback signal chains, and battery-management system (BMS) monitoring. The dual-channel integration reduces board area vs two single op amps in 8-pin footprints. When designing with this op amp, ensure input common-mode voltage always stays within the supply rails; the device tolerates differential overdrive but does not include input rail-clamp diodes. Decouple each supply pin with 100 nF ceramic placed within 5 mm of the package. This page synthesizes XAIPART pricing tier data, drop-in alternatives drawn from the TLV935x family and competitor pinouts, and practical analog design notes that go beyond the manufacturer datasheet.

Permintaan RFG Kontak
TM4C1232H6PMI7 - Tiva C ARM Cortex-M4F MCU 80MHz 256KB | Texas Instruments
TM4C1232H6PMI7

TM4C1232H6PMI7 - Tiva C ARM Cortex-M4F MCU 80MHz 256KB | Texas Instruments

The Texas Instruments TM4C1232H6PMI7 is a 32-bit ARM Cortex-M4F microcontroller in the Tiva C Series, featuring an 80 MHz CPU core with single-precision Floating Point Unit (FPU), 256 KB of single-cycle Flash memory, and 32 KB of SRAM, packaged in a 64-pin LQFP (PM) footprint. It integrates 1 CAN 2.0 A/B controller, USB 2.0 Full-Speed Device (USB-D), and a full set of digital peripherals including up to 6 GPIOs blocks, 8/16-bit EPI/µDMA, and enhanced PWM/CCP blocks for motor and power conversion control. The Tiva C Series microcontroller family is a high-performance 32-bit ARM Cortex-M4F based MCU platform engineered for industrial applications, including remote monitoring, electronic point-of-sale (POS) terminals, test and measurement equipment, network appliances and switches, factory automation, HVAC and building control, gaming equipment, transportation, and fire/security systems. It belongs to the broader ARM Cortex-M microcontroller family and competes in the high-performance Cortex-M4 tier with floating-point DSP instructions, distinguishing it from Cortex-M0/M0+ entry-level parts and Cortex-M7 high-end parts. Key features include hardware single-precision FPU, JTAG and SWD debug interfaces, hibernation module with RTC, two 12-bit ADC modules (1 MSPS), two I2C controllers, four SSI/SPI controllers, and a wide operating voltage range from 3.15 V to 3.63 V with industrial -40°C to +85°C extended temperature grade (the "I7" suffix indicates industrial temperature range and 7 RoHS-compliant lead-free finish). The device's 256 KB flash supports in-field firmware updates via the on-chip ROM-bootloader or the user-software bootloader in flash. Technically, the TM4C1232H6PMI7 uses a Cortex-M4F core with optional Memory Protection Unit (MPU) and a nested vectored interrupt controller (NVIC) supporting deterministic interrupt latency for real-time control loops. The integration of MAC+PHY-less USB Device and CAN enables robust industrial connectivity without external transceiver chips, while the µDMA engine supports scatter-gather transfers that offload data movement from the CPU. Typical applications include industrial control PLCs, building automation HVAC controllers, USB peripherals (HID, CDC, MSC classes), motor control for BLDC/stepper drivers, and networked sensor hubs in factory automation. The "I7" industrial temperature grade and extended reliability tests suit it for harsh industrial environments requiring long operational life. Design consideration: with 64 GPIO pins, careful pin-mux configuration is required via the GPIO Port Control (GPIO_PCTL) registers, and unused pins should be configured as digital inputs with weak pulldown to reduce power. The internal 1.2 V LDO requires bulk decoupling on VDD pins (a 1 µF + 100 nF pair), and the analog VDDA must be tied to VDD with a ferrite bead for ADC noise isolation. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, giving engineering and procurement teams a faster path from selection to BOM.

Permintaan RFG Kontak
TM4C1233H6PGE - 80MHz Cortex-M4F MCU 256KB | Texas Instruments
TM4C1233H6PGE

TM4C1233H6PGE - 80MHz Cortex-M4F MCU 256KB | Texas Instruments

The Texas Instruments TM4C1233H6PGE is a 32-bit Arm Cortex-M4F microcontroller running at 80 MHz with 256 KB flash, 32 KB SRAM, dual CAN 2.0 controllers, RTC, and USB device support, housed in a 144-pin LQFP (20x20 mm) package. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals on one die. Within the semiconductor hierarchy, the TM4C1233H6PGE belongs to the 32-bit embedded microcontroller class, part of the Tiva C Series TM4C123x family built on the Arm Cortex-M4F architecture, which adds a hardware single-precision FPU, DSP instructions, and a Memory Protection Unit (MPU) on top of the standard Cortex-M core. Key features include the 80 MHz core with integrated FPU and MPU, 256 KB of on-chip flash with in-system programming support, 32 KB of SRAM, and a rich peripheral set: up to two CAN 2.0 controllers, USB 2.0 device, multiple UART, SSI, and I2C modules, 12-bit ADCs, PWM generators, and a battery-backed hibernate module with real-time clock. This combination makes the device well suited to mixed-signal industrial control where deterministic real-time response and robust fieldbus connectivity are required. Technically, the device uses the Tiva C Series 123x platform with a nested vectored interrupt controller (NVIC), SysTick timer, and both a precision internal oscillator and main oscillator inputs. Flash-based memory supports firmware updates via CAN or UART bootloaders, easing field maintenance in deployed equipment. Typical applications cited by TI include remote monitoring, electronic point-of-sale machines, test and measurement equipment, network appliances and switches, factory automation, HVAC and building control, and fire and security systems. A key design consideration is SRAM budgeting: enabling USB stacks and RTOS middleware can consume several kilobytes of the 32 KB SRAM, so applications needing more headroom should evaluate the TM4C123GH6PGE variant or the TM4C129x class. This page synthesizes verified distributor data, drop-in same-family alternatives, pricing, and practical design notes not found in the manufacturer datasheet alone.

USD $7,15 Kontak
TM4C1237H6PZI - 80MHz ARM Cortex-M4F MCU 256KB Flash | TI
TM4C1237H6PZI

TM4C1237H6PZI - 80MHz ARM Cortex-M4F MCU 256KB Flash | TI

The Texas Instruments TM4C1237H6PZI is a 32-bit ARM Cortex-M4F microcontroller running at up to 80 MHz, integrating 256 KB of single-cycle Flash and 32 KB of single-cycle SRAM in a 100-pin LQFP (PZ) package. The part integrates a Floating-Point Unit (FPU) for single-precision IEEE 754 math, a memory protection unit, plus Tiva C Series connectivity peripherals including CAN 2.0, USB 2.0 (full-speed), and a real-time clock (RTC) with Hibernation module. An ARM Cortex-M4F microcontroller is a 32-bit MCU core built around the ARMv7-M architecture with hardware single-precision floating-point support, Thumb-2 instruction set, deterministic interrupt handling (NVIC), and tightly-coupled low-latency memory interfaces. In the broader taxonomy, the Cortex-M4F belongs to: Cortex-M4 -> Cortex-M family -> ARMv7-M processors -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. Tiva C Series MCUs sit in TI's general-purpose 32-bit MCU portfolio, alongside MSP432, Sitara, and Hercules safety MCUs. Key features of the TM4C1237H6PZI include 8 UART, 4 SSI/SPI, 4 I2C, 2 CAN, 1 USB, two 12-bit 1-MSPS ADC modules (totaling up to 24 channels), six 64-bit and six 32-bit general-purpose timers, eight PWM outputs, three quadrature encoder interfaces, and a low-pin-count LCD interface on related derivatives. The 80-MHz system clock and single-cycle memory accesses deliver 100 DMIPS of throughput, while the integrated FPU accelerates DSP and control-loop math. Typical applications span industrial remote monitoring, electronic point-of-sale machines, test and measurement equipment, network appliances and switches, factory automation, HVAC and building control, gaming equipment, transportation, and fire/security systems. The combination of CAN and USB makes it a strong fit for industrial gateways; the RTC plus Hibernation module supports battery-backed timekeeping for metering. When designing with this part, ensure the LDO and I/O supply rails are sequenced within the datasheet limits, observe the 100-pin LQFP 1.4 mm thickness for mechanical clearance, and validate that the application's pin multiplexing matches the selected peripheral set.

Permintaan RFG Kontak
TM4C123GE6PZT7R - 80MHz ARM Cortex-M4F MCU, 128KB Flash | TI
TM4C123GE6PZT7R

TM4C123GE6PZT7R - 80MHz ARM Cortex-M4F MCU, 128KB Flash | TI

The Texas Instruments TM4C123GE6PZT7R is an ARM Cortex-M4F based Tiva C Series microcontroller running at 80 MHz with a single-cycle Floating Point Unit (FPU), integrating 128 KB of single-cycle Flash and 32 KB of single-cycle SRAM into a 100-pin LQFP package. Its Cortex-M4F core implements the Thumb-2 instruction set, deterministic nested vectored interrupt controller (NVIC), and hardware divide, single-cycle multiply, and saturated math support for DSP-style operations on a microcontroller footprint. The device is built on a 1.2 V internal core with 3.3 V I/O rails. A microcontroller (MCU) is a single-chip computer integrating a CPU core, volatile and non-volatile memory, and a rich set of programmable peripherals intended for embedded control. The Cortex-M4F class sits in the hierarchy: Cortex-M4F -> Cortex-M series -> ARMv7-M architecture -> 32-bit RISC MCU -> embedded processor -> semiconductor device; the FPU suffix denotes the single-precision IEEE 754 floating point unit. TM4C123GE6PZT7R combines CPU, memory, analog, motion-control, and connectivity peripherals into one IC, replacing what historically required a microprocessor plus external peripherals. Key features include 8 UARTs, 4 I2C, 4 SSI/SPI, 2 CAN 2.0B, USB 2.0 Full-Speed Host/Device/OTG, a 12-bit ADC with 1 MSPS and up to 22 analog inputs, two analog comparators, four general-purpose 16/32-bit timers, two watchdog timers, an Hibernation module with RTC, and a PWM block with fault inputs and dead-band generators. Operating voltage spans 3.15 V to 3.63 V with an LDO-derived 1.2 V core; the MCU is qualified for the industrial -40 °C to +85 °C range. Typical applications include industrial remote monitoring, electronic point-of-sale (POS) terminals, test and measurement front-ends, network appliances and switches, factory automation controllers, HVAC and building-control systems, gaming peripherals, motion-control hobby servos, and lighting controllers. Two integrated CAN controllers make it attractive for distributed industrial nodes and automotive body/motor subsystems. Designers should keep the analog and digital supply rails well decoupled with 100 nF ceramic bypass capacitors placed within a few millimeters of each VDD pin, plus a bulk 10 uF near the regulator output. The 100-LQFP (14x14) package thermal resistance theta_JA of around 47 C/W allows full industrial operation without a heatsink; ensure unused debug and JTAG pins are pulled to defined states when not used to avoid floating-input current draw.

Permintaan RFG Kontak
TM4C1290NCPDTI3R - Tiva C Series 120MHz ARM Cortex-M4F MCU, 1MB Flash | TI
TM4C1290NCPDTI3R

TM4C1290NCPDTI3R - Tiva C Series 120MHz ARM Cortex-M4F MCU, 1MB Flash | TI

The Texas Instruments TM4C1290NCPDTI3R is a high-performance 32-bit ARM Cortex-M4F microcontroller from TI's Tiva C Series, featuring a 120MHz core with FPU, 1MB Flash, and 256KB SRAM, housed in a 128-pin TQFP (14x14 mm) package. The device integrates extensive connectivity including Ethernet MAC+PHY, USB 2.0, CAN, UART, I2C, and SPI, making it well suited for connected industrial and IoT embedded designs. What is an ARM Cortex-M4F microcontroller? An ARM Cortex-M4F microcontroller is a 32-bit MCU based on the ARM Cortex-M4 processor core with single-precision floating-point unit (FPU), DSP extensions, and a Nested Vectored Interrupt Controller (NVIC). The M4F sits in the Cortex-M family hierarchy above Cortex-M0/M0+ (low-power 8/16-bit class performance) and Cortex-M3 (basic 32-bit), delivering deterministic real-time performance with DSP-class signal processing capability. Microcontrollers occupy the embedded computing tier below microprocessors (MPUs) in the system-on-chip taxonomy, integrating CPU, memory, peripherals, and often connectivity IP into one package. Key features of the TM4C1290NCPDTI3R include: integrated 10/100 Ethernet MAC and PHY, USB 2.0 full-speed host/device/OTG, two CAN 2.0B controllers, eight UARTs, ten I2C, four SSI/SPI, a 12-bit 2MSPS ADC with up to 24 analog inputs, and a hibernation module with RTC. The on-chip memory of 1MB Flash and 256KB single-cycle SRAM supports data-logging buffers, TCP/IP stacks (such as lwIP or TI's own NDK), and real-time control loops without external memory in many designs. The 16-bit CRC engine and AES/DES/SHA crypto accelerators (via the TivaWare library) are commonly leveraged for secured connectivity. Typical applications include industrial Ethernet gateways, PLC modules, networked sensors, building automation controllers, USB host peripherals (printers, scanners, POS terminals), automotive telematics, smart energy and smart grid endpoints, and SCADA remote terminal units (RTUs). The wide 3.3V I/O and integrated PHY reduce external BOM for cost-sensitive connected designs. When designing with this MCU, pay close attention to the TQFP-128 thermal performance at high CPU loading. Validate that the hibernation current budget meets battery-backed RTC requirements, and ensure PCB layout keeps the Ethernet differential pairs length-matched within datasheet tolerances. This page synthesizes distributor pricing, drop-in Tiva C alternatives, and practical design guidance not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
TM4C1294NCPDTI3 - 120MHz Cortex-M4F MCU 1MB Flash | TI
TM4C1294NCPDTI3

TM4C1294NCPDTI3 - 120MHz Cortex-M4F MCU 1MB Flash | TI

The Texas Instruments TM4C1294NCPDTI3 is a 32-bit ARM Cortex-M4F microcontroller from the Tiva C Series operating at up to 120 MHz, with 1 MB of flash memory and 256 KB of SRAM, housed in a 128-pin TQFP (14x14 mm) surface-mount package. It integrates an Ethernet MAC with PHY, USB 2.0 Host/Device/OTG, and a rich serial-peripheral set aimed at highly connected IoT designs. A microcontroller (MCU) is a compact integrated circuit that governs specific operations in embedded systems, combining a processor core, memory, and programmable peripherals on a single die. In the product hierarchy, the TM4C1294NCPDTI3 sits within ARM Cortex-M4F core -> Tiva C Series -> TM4C129x family, and it is code-compatible across the Tiva C lineup, letting designers scale designs without rewriting firmware. Key features include the integrated 10/100 Ethernet MAC+PHY for direct network attachment without an external PHY, dual 12-bit ADCs for analog acquisition, and multiple UART, I2C, SPI, and CAN channels. The Cortex-M4F core adds a hardware floating-point unit (FPU), DSP instructions, and a memory protection unit (MPU) for firmware reliability. The industrial temperature grade covers -40C to +85C. Architecturally, the device pairs the 120 MHz M4F pipeline with 256 KB of on-chip SRAM and 1 MB of flash, a JTAG/SWD debug interface, and TI's TivaWare peripheral driver library. The DSP/FPU acceleration enables real-time control loops and digital signal processing without an external co-processor, while the MPU helps isolate critical code regions in safety-conscious firmware architectures. Typical applications include industrial automation nodes, IoT gateways, building automation and smart-grid equipment, networked control systems, and motor control. The integrated Ethernet MAC+PHY removes external components in many designs, cutting BOM cost and board area. Design consideration: decouple all VDD and VDDA pins with low-ESR ceramic capacitors placed close to the package, follow datasheet guidance for the 1.2V core regulator, and exploit low-power sleep modes in energy-sensitive nodes. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
TM4E1231H6ZRBI - Tiva C ARM Cortex-M4 MCU 80MHz 256KB BGA | Texas Instruments
TM4E1231H6ZRBI

TM4E1231H6ZRBI - Tiva C ARM Cortex-M4 MCU 80MHz 256KB BGA | Texas Instruments

The Texas Instruments TM4E1231H6ZRBI is a 32-bit ARM Cortex-M4F microcontroller from the Tiva C (TM4C) Series featuring an 80 MHz core with Floating Point Unit, 256 KB single-cycle Flash, and 32 KB SRAM, packaged in a 157-ball BGA (ZRB package). The part integrates a high-performance analog comparator, two 12-bit ADC modules, multiple UART/SPI/I2C interfaces, and a full-speed USB 2.0 OTG controller with dedicated DMA, suited for industrial control and connectivity-rich embedded designs. An ARM Cortex-M4F MCU is a 32-bit microcontroller that adds a single-precision IEEE 754 Floating Point Unit and DSP extensions to the standard Cortex-M4 architecture. Within the broader taxonomy, this places it as a microcontroller -> embedded processor -> semiconductor device, the same family that includes Cortex-M0/M0+ low-end parts and Cortex-M7 high-performance parts. The 'F' suffix specifically denotes the FPU which is essential for sensor-fusion math, motor-control PI loops, and digital signal processing without integer-only precision loss. Key features include 256 KB Flash with pre-fetch buffer to minimize instruction stalls, 32 KB SRAM with byte-access arbitration, two 12-bit ADC modules each supporting up to 1 MSPS with 12 analog input channels, two CAN 2.0 A/B controllers, a USB OTG full-speed controller with ULPI option, an Ethernet MAC with 1588 timestamp support, and an integrated hibernation module for ultra-low-power battery-backed operation drawing as little as 1.6 uA on VBAT. Architecturally the TM4E1231H6ZRBI uses the Tiva C Series design philosophy combining ARM Cortex-M4F processing with a peripheral-rich pin mux that allows nearly every GPIO to map to alternate functions such as timers, QEI, PWM, and serial interfaces. The device is manufactured on a mature 65 nm process that delivers predictable MHz/mW ratios and supports industrial-grade temperature ranges. Typical applications include industrial motion control, USB-connected human-interface devices, building automation gateways, and factory sensor hubs. The combination of CAN 2.0B, Ethernet, and USB makes the part a strong fit for industrial IoT edge nodes that must bridge legacy field buses with TCP/IP networks. When designing with this device, pay close attention to the BGA157 substrate and use at least 4-layer PCB stack-up with microvia or via-in-pad technology to escape the dense ball grid. Allocate decoupling capacitance directly under the BGA to suppress switching transients during high-speed serial bursts. This page synthesizes current distributor pricing, BGA157 drop-in equivalents, and practical PCB layout guidance not found in the manufacturer datasheet.

Permintaan RFG Kontak
TM4E123GH6ZRBI7 - 80MHz ARM Cortex-M4F MCU, 256KB Flash | TI
TM4E123GH6ZRBI7

TM4E123GH6ZRBI7 - 80MHz ARM Cortex-M4F MCU, 256KB Flash | TI

The Texas Instruments TM4E123GH6ZRBI7 is a 32-bit ARM Cortex-M4F microcontroller from the Tiva C Series with an 80 MHz CPU, 256 KB single-cycle Flash, and 32 KB single-cycle SRAM, packaged in a 157-ball BGA (ZRBI). It includes a floating-point unit, a deterministic interrupt controller, and a rich peripheral set for industrial and consumer embedded applications. Key features include 8 UARTs, 4 I2C modules, 4 SSI/SPI controllers, 2 CAN 2.0 A/B controllers, a 12-bit 2-MSPS ADC with 24 analog inputs, two analog comparators, and a 16-bit PWM timer block with up to 32 PWM outputs. The device operates from 3.3 V (LDO regulation on-chip), supports industrial -40C to +85C temperature ranges, and integrates a JTAG/SWD debug interface. The 157-ball BGA package provides compact routing for high-pin-count designs. The TM4E123GH6ZRBI7 sits within the broader category hierarchy: ARM Cortex-M4F microcontroller -> ARM Cortex-M -> 32-bit microcontroller (MCU) -> microcontroller -> embedded processor -> semiconductor. This taxonomy helps engineers locate the part within the TI ecosystem and competing Cortex-M portfolios from NXP, STMicroelectronics, and Microchip. The architecture combines ARM Cortex-M4F core with TI's peripheral driver library and StellarisWare-compatible APIs. The deterministic interrupt controller provides 7 priority levels with tail chaining, reducing interrupt latency for real-time control. Hardware CRC and a random-number generator support communications protocols requiring data integrity verification. Typical applications include industrial motor control, factory automation, building HVAC, programmable logic controllers (PLCs), sensor aggregation hubs, and human-machine interface (HMI) panels. The 80 MHz core with FPU delivers sufficient throughput for closed-loop PID control while the BGA package suits space-constrained PCB designs with high I/O density. When designing with this part, ensure the BGA's thermal vias are properly stitched to internal ground planes for heat dissipation. Allocate sufficient PCB layers for signal escape routing on the 157-ball array, and use the on-chip LDO regulator mode by tying the VDD25 rail to the internal 2.5 V output. This page synthesizes distributor pricing, drop-in Tiva C Series alternatives, and practical design notes beyond the manufacturer datasheet, giving engineers a single source for selection and sourcing decisions.

Permintaan RFG Kontak
TMC2005-JT - 5-Port ARCNET Hub Controller | Microchip
TMC2005-JT

TMC2005-JT - 5-Port ARCNET Hub Controller | Microchip

The Microchip Technology TMC2005-JT is an ARCNET 5-port hub controller with a parallel processor interface, packaged in a 64-lead TQFP measuring 10 mm by 10 mm. The device provides the central node management required to connect multiple ARCNET branches through a hub or repeater, while supporting twisted-pair and other interfaces through compatible external transceivers. According to the manufacturer datasheet, the controller filters timing jitter of ±100 ns at 2.5 Mbit/s through an internal digital phase-locked loop and buffers the received network data. An ARCNET hub controller is an interface IC in the ARCNET networking hierarchy. It sits between a host processor and external network transceivers, manages access to shared ARCNET media, and expands a network whose node count and cable length are constrained by transceiver electrical capacity. The TMC2005 is intended for embedded systems that need structured cabling, industrial networking, building automation, transportation equipment, or legacy factory data networks rather than general-purpose Ethernet connectivity. Verified device features include a 5-port hub arrangement, a parallel interface, support for HYC9088, RS-485, HYC5000/4000/2000, and TTL optical-module interfaces, and the ability to operate three different transceiver types simultaneously. It can also connect multiple TMC2005 devices to expand hub count. Network nodes connected to one hub must still use the same data rate because the controller does not perform data-rate conversion. The internal digital PLL and receive buffer are particularly useful on noisy or long industrial networks where sampling jitter could corrupt frames. This filtering improves the reliability of packet reception without requiring all connected nodes to share one physical medium. The parallel processor interface allows the surrounding microcontroller or host logic to configure the hub, monitor status, and service the network. A typical implementation places the TMC2005 between a host processor and five external transceiver channels, with termination and connector arrangements selected for the installed cable and topology. Power and signal integrity depend on proper transceiver separation, controlled-impedance routing, and grounding. The manufacturer datasheet states that a TTL optical-module interface can be connected alongside other supported transceivers, but all devices in a single network must operate at the same data rate. This page combines verified manufacturer and distributor information with practical context for ARCNET hub design. It distinguishes controller features from external transceiver duties, highlights the 2.5 Mbit/s jitter-filtering example, and identifies the documentation gaps that should be resolved before a PCB or production qualification. The TMC2005-JT is therefore best treated as a specialized networking interface component rather than a general Ethernet controller.

Permintaan RFG Kontak
TMC2072-MT - CircLink Controller, 100-TQFP | Microchip
TMC2072-MT

TMC2072-MT - CircLink Controller, 100-TQFP | Microchip

The Microchip Technology TMC2072-MT is a dual-mode CircLink network controller with an 8-bit or 16-bit parallel CPU interface, supplied in a 100-TQFP package measuring 14 mm by 20 mm. It supports Peripheral mode with programmable 8-bit I/O and Standalone mode with 16-bit I/O, allowing the controller to support multiple embedded processor architectures. The verified product listing identifies the parallel-interface controller and dual-mode architecture; detailed electrical limits beyond the supplied source data remain unavailable. A CircLink controller provides a hardware-oriented path for connecting control-oriented networks to a host processor. In this context, the controller sits between a CPU bus and external network nodes, handling protocol-specific activity while exposing a conventional parallel interface. The TMC2072 supports multiplexed or non-multiplexed address and data arrangements, which can simplify adaptation to x86, 68XX, SHx, and other processor families identified in the manufacturer datasheet. The TMC2072-MT's main distinguishing features are its selectable 8-bit or 16-bit data-bus width and dual operating modes. Peripheral mode exposes programmable 8-bit I/O for systems where the host processor requires explicit interface control. Standalone mode configures the I/O as 16-bit, reducing host-side involvement when a more autonomous controller configuration is appropriate. These modes let designers balance bus flexibility against control requirements without changing the physical controller package. Technically, the device belongs to the network-controller and parallel-interface-controller hierarchy within the broader semiconductor and embedded-control ecosystem. Its 100-TQFP footprint provides 100 external leads, while the CircLink architecture supports real-time, control-oriented networking. The verified datasheet excerpt also describes flexible CPU interfacing rather than requiring a fixed bus width, helping the controller accommodate different embedded system designs. Typical applications include industrial control systems, embedded automation equipment, networked motion or machine-control modules, real-time supervisory controllers, and custom CircLink nodes. The controller is most appropriate when the host CPU needs direct parallel-bus access to a reliable control network and the system can be designed around the documented electrical, timing, and pin requirements. A key design consideration is host-bus compatibility. The engineer must confirm address and data multiplexing, bus width, I/O direction, timing, reset behavior, and interrupt requirements against the complete manufacturer datasheet before layout. Because only verified source excerpts were supplied, this page does not infer unprovided clock limits, voltage values, current ratings, package tolerances, or environmental grades. This page consolidates verified distributor listings, manufacturer information, the official datasheet link, pricing evidence, package details, and CircLink operating-mode data. It also separates confirmed facts from missing electrical specifications so engineers can make a traceable preliminary design decision and then complete full electrical validation using the manufacturer documentation.

Permintaan RFG Kontak
TMC2072KHC - 3-Channel 8-Bit Genlocking Video Digitizer
TMC2072KHC

TMC2072KHC - 3-Channel 8-Bit Genlocking Video Digitizer

The onsemi TMC2072KHC is a genlocking video digitizer with a 3-channel analog video input multiplexer, 8-bit video quantization, horizontal and vertical synchronization, and an on-chip PLL. It is designed for NTSC and PAL baseband composite-video acquisition and is supplied in a 100-MQFP package. The verified product data identifies the device as a genlocking video digitizer, while detailed operating limits are available in the manufacturer datasheet. A video digitizer is an interface IC that converts analog composite-video signals into digital pixel data for storage, transmission, monitoring, or image-processing systems. The TMC2072KHC combines analog input selection, clamping, gain adjustment, synchronization handling, timing generation, quantization, and digital output in one device. This integration reduces the number of external functional blocks required in professional video equipment. The 3-channel video input multiplexer supports selection among multiple composite-video sources. Analog and digital video clamp functions establish a stable reference level before sampling, while automatic gain adjustment compensates for amplitude variation. Sync detection and separation extract horizontal and vertical timing information for genlocking the digitizer to the incoming video source. According to the manufacturer datasheet description, the on-chip PLL generates a line-locked pixel clock for the internal 8-bit analog-to-digital converter and a double-speed register clock for transferring data to subsequent video-processing logic. This timing architecture is central to converting analog baseband composite NTSC or PAL video into its digital equivalent. Typical uses include broadcast video monitoring, video switching systems, frame synchronizers, production test equipment, industrial inspection, and legacy video capture. The same-package requirement and available board-level evidence must be considered before selecting a replacement. Designers should preserve the analog input, clock, PLL, and digital-output layout recommended in the datasheet and verify timing margins at the intended NTSC or PAL line rate. The verified data does not provide complete pin definitions, absolute maximum ratings, or all timing values in the supplied snippets. This page combines verified distributor information, datasheet search results, package identity, and design-oriented engineering guidance while clearly identifying parameters that require direct confirmation from the manufacturer datasheet.

Permintaan RFG Kontak
TMC2074-NU - Parallel CircLink Controller | Microchip Technology
TMC2074-NU

TMC2074-NU - Parallel CircLink Controller | Microchip Technology

The Microchip Technology TMC2074-NU is a dual-mode CircLink network controller with a parallel host interface, supplied in a 128-VTQFP package measuring 14 x 14 mm. The verified distributor listing identifies it as an active controller IC in the Integrated Circuits > Interface ICs category and provides the package, interface, RoHS status, stock, minimum order quantity, and seven-week lead-time information. Its central role is to connect external network-interface hardware to an embedded host through CircLink rather than requiring a conventional software protocol stack. A CircLink controller is an interface IC within the broader network-controller and data-processing hierarchy. CircLink provides a hardware-oriented communications path between a host system and supported networking devices, helping systems move control and data traffic without the cumbersome middle-layer protocol stacks and complex packet-prioritization schemes identified in the manufacturer description. The TMC2074 therefore belongs to the family of embedded communication and networking semiconductors rather than microcontrollers, analog converters, or general-purpose logic devices. The verified product record identifies the TMC2074 as a flagship CircLink product with a flexible and feature-rich design intended for high-reliability, high-performance, real-time, control-oriented networks. The -NU ordering code is shown with a parallel interface and a 128-VTQFP (14 x 14) package. Because the supplied data does not include the complete electrical timing table, the applicable processor bus details, clock values, transceiver type, or all package-pin functions, those specifications remain explicitly marked as data needed rather than inferred. Typical engineering uses for this controller include industrial control systems, embedded automation equipment, factory data links, motion-control platforms, communications modules, and other real-time networks where deterministic control-oriented communication is valuable. In these systems, the controller can serve as the dedicated interface between a host processor and network hardware, offloading communication-specific traffic handling from the main embedded CPU and helping organize the network architecture. The key design consideration is to use the manufacturer datasheet as the authority for the exact pinout, electrical limits, host-interface timing, power requirements, and supported CircLink configuration. The verified distributor information confirms the 128-VTQFP package and parallel interface, but it does not provide enough detail to specify PCB pin mapping or signal termination safely. This page combines the verified distributor and manufacturer information with explicit data gaps rather than presenting unverified engineering assumptions as specifications.

Permintaan RFG Kontak
TMC2081KBC - 24/16-Bit Digital Video Mixer | Fairchild
TMC2081KBC

TMC2081KBC - 24/16-Bit Digital Video Mixer | Fairchild

The Fairchild Semiconductor TMC2081KBC is a monolithic digital video mixer that proportionally combines digital video sources in GBR, YCBCR444, or YCBCR422 formats and supports 24/16-bit output. It accepts 24/16-bit GBR, YCBCR444, or YCBCR422 inputs together with 8-bit color-index sources, then provides a 24/16-bit mixed output. The device is packaged as a 160-pin PQFP. A digital video mixer is an interface IC that combines or blends multiple digital pixel streams using programmable coefficients rather than analog signal mixing. In the signal hierarchy, the TMC2081 belongs to video interface and video processing within the broader interface IC and semiconductor categories. It is useful when a system must combine graphics, camera, overlay, or chroma-key data before passing the result to downstream video circuitry. The TMC2081 supports proportional mixing through 7-bit coefficients A7-0. The supplied technical material also describes 8-bit color-index inputs, 255-step proportional mixing, 256-step mixing with the A8-0 coefficient path for a value of 100h unity gain, and an 8-bit look-up table on the chroma channel. These features allow designers to adjust source contributions and apply channel-specific processing rather than relying on a fixed video combiner. Operation is digital, which avoids the noise, gain drift, and channel-matching problems commonly associated with analog video mixers. The implementation supports color spaces with 444 and 422 chroma formats and a 24/16-bit output, making the device relevant to professional video, broadcast, monitoring, graphics, and industrial imaging systems that require deterministic pixel-level blending. The main design consideration is digital interface timing and format compatibility. All sources must be mapped to supported resolutions, color spaces, and coefficient formats before the mixer is enabled. Because the available verified data does not state supply voltage, clock frequency, operating temperature, or the full pin map, those values must be confirmed in the manufacturer datasheet and current production documentation before schematic capture. This page combines the verified distributor and manufacturer-datasheet references with application guidance and sourcing context. It also highlights where pin-level, timing, and lifecycle information still requires confirmation, helping engineers distinguish documented capabilities from assumptions.

Permintaan RFG Kontak
TMC2084-HT - 3.3V 48-TQFP CircLink Controller | Microchip
TMC2084-HT

TMC2084-HT - 3.3V 48-TQFP CircLink Controller | Microchip

The Microchip Technology TMC2084-HT is a 3.3 V standalone-mode CircLink network controller and intelligent remote I/O controller packaged in a 48-pin TQFP. It uses an enhanced token-passing protocol, supports CAN-linked distributed I/O, and is designed to work with a host controller such as TMC2074 or TMC2072. The verified source data identifies a 5 Mbps CAN connection, 3.3 V operation, a 48-TQFP 7 mm × 7 mm package, and a parallel interface. A CircLink controller is a semiconductor interface device that extends controller-area network communication to remote I/O nodes. In a token-passing network, one node holds the token and communicates in a defined order, reducing simultaneous transmission contention. The TMC2084 therefore sits between a host node and distributed I/O devices, helping organize network traffic while exposing local control and status information to the host. The TMC2084-HT operates from a 3.3 V low-power CMOS supply and provides 5 V tolerant I/O, allowing it to interface with external circuitry whose logic levels exceed the core supply. The enhanced token-passing protocol supports up to 15 nodes per network according to the verified data. A token-retry mechanism and consecutive node-ID assignment help the controller recover after communication interruptions and organize network participants. The controller supports 64-byte or 128-byte packets, providing a choice between communication efficiency and payload granularity. Its parallel interface makes it suitable for systems where the controller is connected to a host processor or dedicated interface logic. The 48-TQFP package is a surface-mount, fine-pitch package suitable for industrial and embedded control equipment. Typical applications include industrial automation equipment, factory monitoring systems, distributed data-acquisition modules, remote I/O racks, building-control equipment, and embedded test systems. In these systems, the TMC2084 can organize token-based communication between a host controller and remote I/O nodes, reducing the need for a dedicated processor at every node. Designers should verify the exact pin assignments, clocking, reset, interface timing, and electrical limits against the Microchip TMC2084 manufacturer datasheet before layout. Because the available search results provide only a subset of the complete electrical and timing data, values not explicitly present in the verified sources are marked for data completion rather than inferred.

Permintaan RFG Kontak
TMC2084-HT-E2 CircLink Controller | Microchip | Remote I/O
TMC2084-HT-E2

TMC2084-HT-E2 CircLink Controller | Microchip | Remote I/O

The Microchip TMC2084-HT-E2 is a standalone-mode CircLink controller functioning as an intelligent remote I/O controller in a 48-pin LQFP package. The verified source identifies a 40 MHz device with CMOS interfaces, operation from 3 V to 3.6 V, and compatibility with an enhanced token-passing network controlled by a TMC2074 or TMC2072 host node. Its primary role is distributed I/O expansion rather than general-purpose computation or standalone sensor conditioning. A CircLink controller is a dedicated network interface and remote I/O control device. In this architecture, the TMC2084 attaches external I/O nodes to a token-passing serial network, allowing a host controller to supervise distributed digital inputs and outputs. This hierarchy places the device among interface controllers, serial I/O controllers, semiconductors, and CircLink network components. The verified comparison data identifies the TMC2084-HT as an active Microchip device in a 48-pin rectangular low-profile QFP package. The listed electrical data includes a 40 MHz clock, 3 V minimum and 3.6 V maximum supply limits, CMOS technology, a 0.5 mm pitch, and 7 mm package width. These characteristics make it suitable for established CircLink equipment requiring the documented package and supply configuration. The controller uses enhanced token passing rather than a generic host peripheral protocol. In standalone mode, network nodes are controlled by a TMC2074 or TMC2072 host through the CircLink network. Because traffic depends on network behavior, firmware, timing, and system topology, designers should follow the manufacturer datasheet for electrical limits, protocol operation, and application implementation. Typical uses include industrial remote I/O, machine-control distributed interfaces, test equipment, building-control systems, and embedded control networks. The part is most appropriate when an existing CircLink host architecture can communicate with it and the PCB footprint matches the documented 48-pin package. A key procurement consideration is lifecycle and sourcing. Search results describe the family as active and show multiple distributor listings, but package-qualified alternatives were not established by the supplied cross-reference evidence. Engineers should therefore treat TMC2084-HT-E2 as a system-specific procurement choice rather than assume an interchangeable controller. This page consolidates verified manufacturer information, distributor availability evidence, technical comparison data, and procurement guidance. It distinguishes published facts from unavailable electrical details and avoids presenting unreferenced replacements as drop-in devices.

Permintaan RFG Kontak
TMC22053KHC - Multistandard Video Decoder | onsemi
TMC22053KHC

TMC22053KHC - Multistandard Video Decoder | onsemi

The onsemi TMC22053KHC is a multistandard digital video decoder in a 100-pin BQFP package. It accepts line-locked or subcarrier-locked composite, YC, or D1 digital video and produces digital component signals in multiple output formats. The device is designed for professional broadcast-video equipment that requires decoding and digital component processing within one integrated circuit. Its stated analog supply range is 4.75 V to 5.25 V, while the verified digital supply information is incomplete. A digital video decoder is an interface IC that converts legacy analog video signals into digitized component-video data. Within the product hierarchy, the TMC22053KHC is a video decoder, interface IC, signal-processing semiconductor, and integrated circuit. Decoder ICs sit between incoming video sources and downstream buffers, scalers, processors, transmitters, or digital recording equipment. They are commonly used in studio monitors, broadcast equipment, video switching systems, and professional capture products rather than ordinary consumer televisions. The TMC22x5y decoder family is presented as a broadcast-quality video-processing solution combining multistandard input acceptance with digital component generation. Supported input modes include composite, YC, and D1, and the outputs are available in several digital-component formats. This combination can reduce the number of separate conversion stages required in a professional video path. The exact supported output list, timing limits, resolution modes, and channel mapping require confirmation against the manufacturer datasheet. The KHC suffix identifies the supplied 100-BQFP package in the verified distributor records, and those records describe the component as active and intended for bulk packaging. The package provides 100 external leads for power, analog video, digital video, control, memory-interface, and synchronization functions. Exact pin assignments are not exposed in the supplied verified data, so a complete pinout cannot be reproduced without the manufacturer pinout diagram. TMC22053KHC fits studio television equipment, broadcast monitoring, professional video conversion, digital video routing, and embedded legacy-video acquisition systems. The principal design benefit is integration: accepting several input standards and producing digital component signals can simplify signal-chain partitioning when the downstream processor expects component video. System designers must still validate timing, sync polarity, colorimetry, blanking behavior, and interface voltage compatibility. The key engineering consideration is supply and interface planning. The analog core is specified for 4.75 V to 5.25 V, so layout must provide clean, stable rails and adequate decoupling. Digital-logic connections require confirmation of supply limits and voltage thresholds. PCB signal integrity also depends on keeping analog inputs away from switching-node and high-current return paths, while the large 100-lead BQFP requires careful fanout, ground-plane continuity, and via placement. This page consolidates the verified onsemi-family product description, distributor pricing, package information, comparison guidance, and practical integration notes. It distinguishes verified facts from parameters that still require confirmation from the datasheet, helping engineers source the part while avoiding unsupported assumptions about pinout, timing, compliance, or replacement behavior.

Permintaan RFG Kontak
TMC22090R0C - RGB to NTSC/PAL Video Encoder | Fairchild
TMC22090R0C

TMC22090R0C - RGB to NTSC/PAL Video Encoder | Fairchild

The Fairchild Semiconductor TMC22090R0C is an RGB-to-NTSC/PAL color-signal video encoder integrated circuit packaged in an 84-pin PLCC. The verified distributor record identifies the device as a video encoder IC that converts RGB signals into composite NTSC or PAL video, making it suitable for legacy analog-video equipment, industrial imaging systems, video test equipment, and signal-generation applications. Its 29.31 mm by 29.31 mm PLCC package is supplied in the R0C ordering configuration, and the listed distributor price is $13.8014 as of 2026-10-28. A video encoder is an interface IC that translates RGB color information into a composite analog video waveform accepted by displays, recorders, monitors, and broadcast-related equipment. The TMC22090R0C belongs to the broader integrated-circuit hierarchy of interface ICs, video signal-processing ICs, color encoders, and signal-conversion semiconductors. NTSC and PAL are legacy analog television color systems, so this component is primarily relevant to equipment that still supports composite-video interfaces rather than modern digital HDMI, DisplayPort, or camera-sensor interfaces. The verified product classification establishes RGB input, NTSC/PAL output, and the 84-PLCC package. Specific operating voltages, current consumption, clock requirements, synchronization behavior, input levels, output impedance, resolution limits, temperature range, and electrical performance ratings were not present in the supplied records. Those parameters must therefore be confirmed from the manufacturer datasheet before schematic capture, signal-integrity simulation, production release, or replacement qualification. The 84-pin PLCC package exposes substantially more external connections than a compact mixed-signal IC, suggesting a feature-rich legacy encoder implementation with multiple data, synchronization, control, power, and ground connections. Because the exact pin map and exposed-pad arrangement are unavailable in the verified data, engineers should not infer individual pin functions from the package count. The electrical connection must follow the official TMC22090 datasheet and its recommended application circuit rather than a generic PLCC footprint. Typical application areas include RGB-to-composite-video adapters, industrial monitor and control-panel interfaces, broadcast-equipment test fixtures, educational video laboratories, and repair or modernization systems that must preserve NTSC or PAL output. The device is also relevant where an existing system accepts analog composite video but produces RGB internally. Its usefulness depends on matching the source RGB timing, sync polarity, reference level, and target television standard to the encoder's documented operating conditions. A critical design consideration is that a correct package and function description does not guarantee an acceptable composite-video output. Input levels, blanking, synchronization, chrominance alignment, and output termination must be verified against the manufacturer specifications. PCB layout should follow the datasheet's routing and grounding guidance, and unused inputs should be handled according to the documented application circuit rather than by assumption. This page consolidates the verified distributor listing, current price reference, package information, product classification, sourcing links, and drop-in-replacement status for the TMC22090R0C. It also distinguishes documented facts from parameters that still require datasheet confirmation, helping engineers avoid unsupported assumptions when sourcing or designing around this legacy RGB-to-NTSC/PAL video encoder.

Permintaan RFG Kontak
TMC22091KHC - RGB to NTSC/PAL Video Encoder | Fairchild
TMC22091KHC

TMC22091KHC - RGB to NTSC/PAL Video Encoder | Fairchild

The Fairchild Semiconductor TMC22091KHC is an all-digital RGB-to-NTSC/PAL video encoder IC packaged in a 100-lead metric quad flat package measuring 20 mm by 14 mm. It accepts digital RGB computer-image or graphics data in 24-bit and 15-bit GBR/RGB 444 formats, as well as color-indexed data, and converts those inputs into a standard analog baseband television signal with a modulated color subcarrier. The device also accepts a CCIR-601 signal and provides a microprocessor interface, frame-buffer interface, genlock interface, and JTAG test interface. A digital video encoder is a semiconductor that converts digital pixel data into a conventional analog video waveform. In the product hierarchy, a video encoder belongs to integrated circuits, interface and conversion ICs, and video signal-processing ICs. Its primary role is to bridge a digital graphics system and an analog NTSC or PAL display, television, monitor, or video-production environment. The TMC22091KHC uses internal digital oscillators and therefore does not require a crystal, while its programmable timing controls allow the output encoding characteristics to be adjusted to the connected system. Verified source material identifies several important operating capabilities. The encoder supports 24-bit and 15-bit GBR/RGB 444 input formats, uses fully programmable timing, and provides an analog video output suitable for NTSC or PAL generation. Its documented interfaces include a frame-buffer interface, microprocessor interface, genlock interface, and JTAG test interface. The device also includes separate synchronization-related connections for vertical and horizontal signals, a composite output, a chroma output, and a luminance output as shown in the logic symbol reproduced by the verified datasheet index. Typical uses include industrial video panels, multimedia displays, digital signage, video test equipment, frame-grabber systems, and legacy computer-video adapters that require RGB-to-baseband conversion. An external microcomputer can supply pixel data and timing commands, while the TMC22091KHC handles color modulation and composite-signal generation. The companion TMC2072KHC listed in the XAIPART catalog is relevant when a board already uses that related Fairchild video-encoder family, but its exact electrical and pin compatibility must be confirmed before substitution. The primary design consideration is interface verification. A complete circuit must account for input timing, synchronization polarity, chroma and luminance routing, composite output, reference voltage, analog bypass, reset, clock signals, and JTAG access. Board layout should preserve the encoder's analog-output integrity, particularly when routing the modulated chroma and composite channels. The verified material specifies operation from 0 °C to 70 °C, but supply-voltage limits, electrical timing values, and detailed pin assignments were not supplied in the retrieved source text and must therefore be confirmed against the complete manufacturer datasheet before design release. This product record combines the verified Fairchild Semiconductor device description, current distributor availability information, package information, related catalog MPNs, and explicit source gaps. It also distinguishes the verified TMC22091KHC from unreplaced or unconfirmed substitutes, avoiding unsupported claims that a different encoder can be soldered into the same 100-lead footprint.

Permintaan RFG Kontak