Produk (44.000+)

TJA1051AT/3/0Z - 5 Mbps CAN Transceiver | NXP
TJA1051AT/3/0Z

TJA1051AT/3/0Z - 5 Mbps CAN Transceiver | NXP

NXP Semiconductors TJA1051AT/3/0Z is a 5 Mbps high-speed CAN transceiver for automotive applications, supplied in an 8-pin SOIC package. It provides one differential transmitter and one differential receiver between a CAN protocol controller and the physical two-wire CAN bus. The device operates from a 5 V supply and supports normal and silent operating modes according to the NXP product description. A CAN transceiver is an interface IC within the broader automotive communication hierarchy. It converts logic-level TXD and RXD signals from a CAN controller into the balanced differential signaling used by a Controller Area Network bus. The differential bus interface improves common-mode rejection, while the transceiver's physical-layer circuitry connects controller-level data communication to CANH and CANL conductors. The TJA1051 therefore belongs to the CAN transceiver, interface IC, automotive communication, and semiconductor product categories. The TJA1051 family is intended for high-speed CAN networks in automotive environments. According to NXP, the third-generation TJA1051 delivers differential transmit and receive capability while providing enhanced electromagnetic compatibility and electrostatic-discharge protection. These characteristics are important in vehicle systems where cable harnesses, switching power converters, motors, and long interconnect paths can introduce noise and transients into the communication bus. The TJA1051AT/3/0Z supports data rates up to 5 Mbps and uses a 5 V automotive CAN interface. Its normal mode provides active bus communication, while silent mode allows the controller-side receive path to monitor bus activity without driving the bus. This feature supports diagnostic and monitoring workflows where a node may need to observe CAN traffic without introducing a dominant output state. Typical installations include body-control modules, powertrain controllers, electric-vehicle subsystems, gateway units, engine-management electronics, and automotive sensor nodes. In these systems, the CAN controller generates serial TXD data, the TJA1051 converts it into CANH and CANL differential signals, and the receiver converts incoming bus states into RXD for the controller. PCB implementation requires careful connection of supply and ground pins, short CANH and CANL routes, and a suitable termination strategy at each end of the bus. Power and ground pins should be decoupled close to the device, while the bus pins should connect through the application's protection and filtering network. The manufacturer datasheet should be used to confirm the exact pin assignments, electrical limits, recommended application circuit, and transceiver I/O characteristics for the SOIC-8 variant. This product page combines the NXP manufacturer description, distributor package and ordering information, and cross-reference results into an engineering-focused selection resource. It highlights the 5 Mbps, 5 V, single-driver, single-receiver, normal/silent-mode, automotive, AEC-Q100, and 8-pin SOIC attributes, while also identifying SOIC-8 drop-in candidates and the checks required before replacing a transceiver in a safety-relevant vehicle network.

Permintaan RFG Kontak
TJA1051T - High-Speed CAN Transceiver | NXP Semiconductors
TJA1051T

TJA1051T - High-Speed CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1051T is an active high-speed CAN transceiver that interfaces a CAN protocol controller with a physical two-wire CAN bus. The device provides differential transmit and receive capability for automotive high-speed CAN systems and is supplied in an 8-pin SOIC package. NXP identifies the TJA1051 as backward compatible with the TJA1050, while the TJA1051T/3 and TJA1051TK/3 variants support direct interfacing with microcontrollers operating from supply voltages as low as 3 V. The verified product information confirms active lifecycle status and links to the manufacturer data sheet. A CAN transceiver is the physical-layer interface between a digital CAN controller and the wired CAN network. It converts controller logic levels into differential bus signals and converts received bus levels into a logic signal understood by the controller. The two-wire CAN bus consists of CANH and CANL conductors, allowing multiple nodes to communicate over a shared differential network while reducing sensitivity to common-mode noise. The TJA1051 family is intended for high-speed in-vehicle communication systems where robust differential signaling and direct integration with automotive microcontrollers are important. The manufacturer describes the TJA1051T as a high-speed CAN transceiver, and its compatibility with the TJA1050 provides a documented migration path for designs that retain an existing SOIC-8 footprint and pin arrangement. The TJA1051T/3 variant is the 3 V-compatible option when the connected CAN controller uses a lower supply voltage. Electrical operating details such as maximum data rate, supply range, transmitter propagation delay, receiver thresholds, bus-fault tolerance, ESD ratings, thermal limits, and package dimensions were not included in the supplied search excerpts. Those values are therefore not restated here; engineers should verify them in the NXP TJA1051 manufacturer data sheet before release. The data sheet also distinguishes standard, /3, and /E product variants, which should not be treated as identical ordering codes. TJA1051T is typically positioned between a CAN-capable microcontroller and the CANH/CANL bus network. Practical implementations require correct termination, common-mode grounding, protection strategy, and transceiver-loop layout. The SOIC-8 package makes the device suitable for conventional surface-mount PCB assembly, although production designs must use the exact land pattern and pin definitions specified by NXP. This page consolidates the verified NXP product-page information, manufacturer data-sheet link, distributor references, and identified same-footprint alternatives. It also distinguishes documented TJA1051 variants and highlights the engineering trade-offs between the standard TJA1051T, the 3 V-compatible TJA1051T/3, and the Silent Mode TJA1051T/2Z. Pricing, availability, and detailed electrical ratings require confirmation from current authorized distribution channels as of 2026-10-28.

Permintaan RFG Kontak
TJA1051T/1J - 5 Mbit/s High-Speed CAN Transceiver | NXP
TJA1051T/1J

TJA1051T/1J - 5 Mbit/s High-Speed CAN Transceiver | NXP

The NXP TJA1051T/1J is a 5 Mbit/s high-speed CAN transceiver with 5 V operation, differential transmit and receive capability, and an 8-pin SOIC package. It interfaces a CAN protocol controller to a physical two-wire CAN bus and is associated with automotive applications. The device is also described as normal-mode, SILENT-mode-capable and AEC-Q100 qualified in the supplied component data. A CAN transceiver is the physical-layer interface between a microcontroller or dedicated CAN controller and the CAN bus. The controller generates and interprets logic-level CAN TX and RX signals, while the transceiver converts those signals into the differential CANH and CANL bus signals. A high-speed CAN physical layer supports differential signaling, noise rejection and reliable communication over twisted-pair wiring. The TJA1051T family is positioned for high-speed CAN networks at data rates up to 5 Mbit/s. The verified component listing identifies a nominal 5 V supply, normal/silent operation, 8-pin SO packaging and tape-and-reel ordering for TJA1051T/1J. NXP also states that TJA1051T is backward compatible with the TJA1050, which is important when upgrading an existing CAN interface. The TJA1051 provides separate transmit-dominant, silent and receive behavior for bus management. Silent mode can be useful when a node must monitor or receive without driving the bus, although network software must coordinate this state with other nodes to avoid hidden transmitter conflicts. The device should be paired with an appropriate CAN controller, bus termination, common-mode protection and a correctly decoupled 5 V supply. Typical installations include automotive body, powertrain-adjacent, gateway and diagnostic networks; industrial automation equipment; elevator and building-control systems; and embedded CAN gateways. The 5 Mbit/s capability suits short, well-terminated, high-quality CAN networks where maximum latency is more important than long cable distance. In every case, PCB layout, grounding and bus protection remain critical. For layout, place the transceiver close to the bus connector, provide a continuous ground reference, route CANH and CANL as a coupled pair, and place termination only at the physical ends of the bus. Avoid long stubs between the transceiver and connector. Power filtering and common-mode chokes may be needed when the cable leaves the controlled PCB environment. This page combines the verified NXP and distributor information with practical selection, layout and sourcing guidance. It also distinguishes verified facts from parameters that require confirmation from the complete manufacturer datasheet or current distributor inventory before design release.

Permintaan RFG Kontak
TJA1051T/1U - High-Speed CAN Transceiver | NXP | Automotive
TJA1051T/1U

TJA1051T/1U - High-Speed CAN Transceiver | NXP | Automotive

The NXP Semiconductors TJA1051T/1U is a high-speed CAN transceiver in an 8-pin SO package. It provides the physical-layer interface between a microcontroller-based CAN protocol controller and a two-wire CAN bus, combining differential transmit and receive capability for automotive high-speed CAN networks. The available manufacturer information identifies the TJA1051 family as active and specifically describes the TJA1051T as backwards compatible with the TJA1050. A CAN transceiver, also called a CAN physical-layer interface, converts logic-level TXD and RXD signals into the differential CANH and CANL bus signals. It belongs to the hierarchy CAN transceiver > CAN physical-layer interface > network interface IC > interface IC > semiconductor. This physical-layer device complements a CAN controller such as those integrated into automotive microcontrollers; it does not replace the protocol controller or its message-handling firmware. The TJA1051T family includes differentiated order-code options for specific design constraints. The NXP datasheet states that TJA1051T/3 and TJA1051TK/3 support direct interfacing with microcontrollers operating from supply voltages down to 3 V. It also states that TJA1051T/E can be switched into a very low-current Off mode. These options provide distinct low-voltage-interface or low-power-selection paths, while TJA1051T/1U remains the specifically requested 8-SO device. The transceiver's two-wire CAN interface and differential signaling support communication over a shared bus designed for high-speed automotive data exchange. Exact data-rate limits, loop-delay timing, bus fault levels, supply range, transceiver state currents, and ESD ratings are not included in the supplied verified snippets, so they must be confirmed in the NXP datasheet before release of a safety- or production-critical design. Typical uses include distributed vehicle networking, body and chassis control modules, powertrain-related control units, gateway electronics, and industrial CAN equipment connected to the same physical bus concept. In each application, the microcontroller handles protocol framing while the TJA1051 family handles the electrical interface to CANH and CANL. PCB implementation requires an 8-SO footprint, correct termination and common-mode handling, and a CAN bus layout that minimizes radiated emissions and susceptibility. Designers should also verify the exact logic and enable behavior of TJA1051T/1U because the requested order code differs from the explicitly documented /3 and /E variants. This page consolidates the verified NXP product information, official datasheet link, distributor identification, package details, and sourced drop-in alternatives. It also highlights which electrical ratings remain unverified so engineers can compare procurement options without mistributing catalog snippets for complete device specifications.

Permintaan RFG Kontak
TJA1051T/2Z - 5 Mbit/s Silent-Mode CAN Transceiver | NXP
TJA1051T/2Z

TJA1051T/2Z - 5 Mbit/s Silent-Mode CAN Transceiver | NXP

NXP Semiconductors TJA1051T/2Z is a 5 Mbit/s high-speed CAN transceiver with Silent Mode, packaged in an 8-pin SOIC for interface bridging between a CAN protocol controller and a physical two-wire CAN bus. The verified distributor listing identifies the /2 ordering option as a Silent-Mode variant, while the manufacturer document covers the TJA1051T family and its compatibility with TJA1050. Its differential transmit and receive arrangement supports automotive and industrial Controller Area Network nodes. A CAN transceiver is the physical-layer interface within a Controller Area Network. It converts controller TXD and error-indicator signals into differential bus output, then converts differential bus levels into RXD data for the protocol controller. This device sits between digital microcontroller I/O and the CAN_H and CAN_L network conductors, combining bus-driver, receiver, and control functions in one IC. The TJA1051T/2Z headline characteristics are a maximum listed data rate of 5 Mbit/s and an 8-pin SOIC package. Silent Mode provides an operating state identified by the verified product listing, but the supplied excerpts do not quantify its input, output, or supply current. The manufacturer also states that the TJA1051T is backward compatible with the TJA1050, which is important when upgrading an existing CAN node without changing its controller-facing interface. The TJA1051 family targets high-speed CAN networks, including automotive systems, where robust differential signaling and transceiver integration simplify node construction. Differential bus operation rejects common-mode noise better than a single-ended interface when the network, termination, grounding, and connector implementation are correctly designed. This makes the part suitable for vehicle body electronics, industrial automation equipment, embedded controllers, and CAN-based sensors. The primary design consideration is preserving compatibility at both the software and physical layers. A replacement must match the SOIC-8 footprint, pin functions, supply expectations, bus timing, and controller logic. Bus termination, common-mode range, loop delay, recessive/dominant behavior, and maximum cable length must be checked against the complete network design rather than inferred solely from the 5 Mbit/s headline rate. For sourcing and engineering context, this page combines the exact verified distributor identity, manufacturer datasheet link, availability claims, family-level compatibility information, and practical design guidance. It separates verified facts from unspecified electrical details so procurement teams can review TJA1051T/2Z without relying on unverified substitutions.

Permintaan RFG Kontak
TJA1051T/3 - 5 Mbit/s CAN FD Transceiver, SOIC-8 | NXP
TJA1051T/3

TJA1051T/3 - 5 Mbit/s CAN FD Transceiver, SOIC-8 | NXP

The NXP Semiconductors TJA1051T/3 is a high-speed CAN FD transceiver in an 8-pin SOIC package, delivering data rates up to 5 Mbit/s in the CAN FD fast phase from a 5.5 V supply, with a separate VIO input that allows direct interfacing with 3 V to 5 V microcontrollers. The device is fully ISO 11898-2:2003 compliant and is designed for 12 V and 24 V automotive and industrial systems. A CAN transceiver is a physical-layer interface device that converts the logic-level TXD and RXD signals of a CAN protocol controller into the dominant and recessive differential voltage levels carried by the two-wire CAN bus, and converts bus levels back into a logic-level RXD signal. In the classification hierarchy, a CAN transceiver is a bus transceiver, then a line interface IC, then an interface IC, and finally a semiconductor. Key features of the TJA1051T/3 include guaranteed timing for data rates up to 5 Mbit/s in the CAN FD fast phase, low electromagnetic emission (EME) combined with high electromagnetic immunity (EMI), and a VIO input pin that lets a 3 V MCU drive the logic side directly without a level shifter. It also exhibits predictable, passive bus behavior when the device is unpowered, and features improved ESD and EMC performance compared with earlier CAN transceiver generations. Architecturally, the TJA1051 belongs to NXP's third generation of CAN transceivers, adding enhanced EMC and ESD behaviour over the earlier TJA1050 family while keeping the classic 8-pin SOIC footprint that dominated automotive body and comfort electronics. Because CAN FD raises the arbitration phase to the classic CAN rate and only the data phase to 5 Mbit/s, the device is commonly paired with CAN FD-capable controllers. Typical applications include automotive body control modules and comfort systems, industrial automation and factory fieldbus gateways, building automation and HVAC controllers, medical monitoring equipment with networked sensors, and CAN-based robotics or test instrumentation. The 8-pin SOIC footprint also keeps the part compatible with legacy PCB layouts that previously carried a TJA1050 or TJA1042. When designing around the TJA1051T/3, keep the CANH and CANL traces short, symmetric and away from high-current switching nodes, and place the 60 nF bus split capacitor close to the bus connector. Because the transceiver draws its supply from a 5.5 V rail and its logic side from VIO, budget both rails correctly and never leave the VIO pin floating. This page consolidates device specifications, verified distributor availability, drop-in pin-compatible alternatives, and practical PCB and EMC design notes that are not consolidated in a single place in the manufacturer documentation.

Permintaan RFG Kontak
TJA1051T/3/1J - 5 Mbit/s CAN Transceiver | NXP
TJA1051T/3/1J

TJA1051T/3/1J - 5 Mbit/s CAN Transceiver | NXP

The NXP Semiconductors TJA1051T/3/1J is a high-speed CAN bus transceiver with a maximum CAN data rate of 5 Mbit/s, a 5.5 V supply rating, and direct support for microcontroller I/O levels from 3 V to 5 V. The device is supplied in an 8-pin SOIC package and provides the physical-layer interface between a CAN protocol controller and a two-wire CAN bus. A CAN transceiver is an interface IC within the CAN controller hierarchy and the broader industrial and automotive networking ecosystem. It converts the controller's transmit and receive logic signals into differential CAN bus levels and presents received bus data to the controller. The TJA1051 family is intended for high-speed CAN networks and provides passive behavior on the bus when its supply is off. Key features include a 5 Mbit/s maximum data rate, improved electromagnetic compatibility, enhanced electrostatic-discharge performance, and compatibility with 3 V to 5 V microcontroller supply levels. The VIO-related version supports direct connection to microcontrollers operating at those lower I/O voltages, which simplifies interfacing between a 5 V transceiver supply and a 3.3 V CAN controller. Technically, the transceiver bridges a logic-domain CAN controller and a differential physical bus. Its TXD input accepts controller command data, while RXD reports received bus state to the controller. CANH and CANL carry the complementary differential signal, and the S input supports standby behavior when the device supports that operating mode. The manufacturer datasheet specifically notes backwards compatibility with the TJA1050. Typical uses include automotive body and comfort electronics, industrial automation controllers, building automation equipment, robotics, diagnostic interfaces, and embedded CAN gateways. The device is particularly appropriate when a 3.3 V controller must communicate through a 5 V CAN transceiver without adding level-shifting circuitry between TXD, RXD, and S. Designers should provide the bus termination and common-mode installation required by the CAN network rather than relying on the transceiver for termination. Decoupling close to VCC and VIO, controlled bus stubs, correct grounding, and an appropriate CAN controller timing configuration are essential for reliable operation. This page consolidates the verified manufacturer and distributor information, practical application guidance, parameter comparisons, and verified drop-in alternatives. It also distinguishes documented TJA1051 family differences from broader functional equivalents so engineers can assess PCB compatibility without confusing protocol speed or standby behavior with physical pin compatibility.

Permintaan RFG Kontak
TJA1051T/3/1U - 3V High-Speed CAN Transceiver | NXP
TJA1051T/3/1U

TJA1051T/3/1U - 3V High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1051T/3/1U is a 3 V-compatible high-speed CAN transceiver that connects a CAN protocol controller to a physical two-wire CAN bus. It is packaged in an 8-pin SOIC and supports direct interfacing with microcontrollers operating from 3 V to 5 V. The device provides one CAN transceiver channel and supports data rates up to 5 Mbit/s. A CAN transceiver is an interface IC within the Controller Area Network communication hierarchy. It converts logic-level TXD and RXD signals used by a CAN controller into the dominant and recessive voltage levels carried by CANH and CANL. The TJA1051 family also provides bus-side protection, fault-tolerant operation, and passive behavior when the device is not powered, helping a controller remain operational during certain bus faults. The TJA1051 is described as a third-generation CAN transceiver with improved electromagnetic compatibility and electrostatic-discharge performance compared with earlier generations. Its VIO connection allows TXD, RXD, and STB signal levels to match the supply voltage of the connected microcontroller. This is particularly useful in mixed 3 V and 5 V systems where a bus transceiver must interface cleanly with modern low-voltage controllers. The TJA1051T/3 family supports a maximum CAN data rate of 5 Mbit/s and can operate with controller supply voltages down to 3 V. Its high-speed CAN architecture suits passenger vehicles, commercial vehicles, industrial automation systems, and embedded control networks. The SOIC-8 package supports conventional surface-mount assembly and offers a compact interface between a host controller and an external CAN bus. Typical applications include automotive body and comfort systems, industrial PLC and factory automation networks, robotics controllers, building automation equipment, and embedded CAN gateways. Because CAN uses a shared multidrop bus, correct termination, grounding, routing, and decoupling remain as important as the transceiver selection itself. When laying out a PCB, place the transceiver close to the CAN connector and keep the CANH and CANL route symmetrical. Route TXD and RXD as controlled-impedance digital signals, provide local supply decoupling, and avoid placing sensitive analog or high-speed clock traces alongside the bus conductors. Verify timing, bus fault behavior, termination, and logic compatibility before production release. This product record combines the NXP family description with application guidance for engineers evaluating the TJA1051T/3/1U. It highlights the 3 V controller interface, 5 Mbit/s bus capability, SOIC-8 packaging, practical PCB considerations, and the distinctions that must be checked when considering a replacement or a related CAN transceiver.

Permintaan RFG Kontak
TJA1051T/3/2Z - 5 Mbit/s CAN Transceiver | NXP | Automotive
TJA1051T/3/2Z

TJA1051T/3/2Z - 5 Mbit/s CAN Transceiver | NXP | Automotive

NXP Semiconductors TJA1051T/3/2Z is a third-generation high-speed Controller Area Network transceiver that supports data rates up to 5 Mbit/s. It interfaces a CAN protocol controller with a physical two-wire CAN bus and includes a VIO input for direct connection to 3 V or 5 V microcontroller I/O supplies. The device is supplied in an 8-pin SOIC package for surface-mount automotive and industrial electronics. A CAN transceiver is an interface IC within the broader physical-layer network-communication hierarchy. It converts logic-level TXD and RXD signals into the differential CANH and CANL bus signals, while receiving the bus state and presenting a compatible logic signal to the host controller. CAN is a deterministic, robust multi-master bus widely used in vehicle networks, industrial automation, robotics, and embedded control systems. The TJA1051T/3 variant combines a 5 Mbit/s maximum data rate with selectable VIO operation, allowing its TXD, RXD, and S interface signals to match a 3 V or 5 V microcontroller. NXP describes the TJA1051 family as backward compatible with the TJA1050 and as offering improved electromagnetic compatibility and electrostatic-discharge performance compared with earlier generations. The selected variants also support direct interfacing with microcontrollers operating from 3 V to 5 V. The TJA1051T/3/2Z provides passive behavior when unpowered, helping prevent interference with an active CAN bus. Its silent-mode S input supports low-power or bus-disconnection requirements, while the VIO pin independently adapts the digital interface voltage. These features make the device useful in body controllers, powertrain controllers, gateway modules, industrial CAN equipment, and sensor nodes where EMC robustness and low-voltage logic compatibility are important. Common automotive CAN systems place the transceiver between the vehicle’s CAN protocol controller and the CANH/CANL conductors. The bus normally uses a twisted-pair harness, 120 Ω termination at each end, and common-mode choke or split termination where required. Firmware can use the S input for silent mode, while the VIO connection must match the host controller’s supply voltage to prevent excessive input voltage or inadequate output drive. Designers should follow the manufacturer’s pin configuration and application diagrams when assigning TXD, RXD, VIO, VCC, CANL, CANH, S, and ground connections. Decoupling capacitors should be placed close to the supply pins, and the CAN bus layout should minimize stub lengths. The PCB footprint must follow the 8-pin SOIC dimensions and pin numbering shown in the package drawing. This product page combines the manufacturer’s device description with a practical view of interface voltage, bus speed, package compatibility, application fit, and engineering trade-offs. It also identifies verified drop-in alternatives for sourcing and design-review decisions without relying on generic distributor recommendations.

Permintaan RFG Kontak
TJA1051T/CM - 5Mbit/s High-Speed CAN Transceiver | NXP
TJA1051T/CM

TJA1051T/CM - 5Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1051T/CM is a high-speed CAN transceiver with a 5 Mbit/s data rate, designed to connect a CAN protocol controller to a two-wire CAN bus. It is supplied in an 8-pin SOIC surface-mount package for compact automotive and industrial control electronics. The device provides differential transmit and receive functions while placing the CAN physical-layer interface close to the host processor or microcontroller. A CAN transceiver is an interface IC within the Controller Area Network hierarchy. It converts logic-level TXD and RXD signals into the dominant and recessive voltage levels used by a wired CAN network, while also receiving bus information for the controller. The TJA1051T/CM therefore connects a digital CAN controller to the physical wiring of a multi-node vehicle, industrial machine, or embedded communications system without requiring the controller to handle the bus electrical layer directly. The TJA1051 family is identified by NXP as a third-generation high-speed CAN transceiver with enhanced electromagnetic compatibility performance. Its 5 Mbit/s capability supports data transfer rates commonly required by automotive body, chassis, comfort, and controller-area-network systems. Differential bus signaling helps reject common-mode noise, while the dedicated TXD and RXD paths provide a clear separation between commands sent to the bus and data returned to the CAN controller. The eight-pin SOIC package supports compact surface-mount assembly and exposes the CANH and CANL bus terminals, VCC, ground connections, TXD, and RXD. This arrangement allows the transceiver to be placed close to the bus connector and controller, reducing the distance over which sensitive signals and supply connections must travel. Exact operating voltage, ESD ratings, standby behavior, and temperature limits should be confirmed in the manufacturer datasheet before final circuit release. Typical uses include automotive CAN gateways, body-control modules, electric-window and seating controllers, industrial automation equipment, sensors, and embedded diagnostic systems. In each application, the CAN controller handles frame construction, arbitration, acknowledgments, and higher-level protocols, while the TJA1051T/CM handles the physical-layer voltage conversion and bus-interface function. This division allows the host processor to work with ordinary digital logic while multiple nodes communicate over a shared two-wire network. PCB design should prioritize short CANH and CANL routes, a compact common return path, and placement of the transceiver close to the bus connector. The bus-side network also needs termination, filtering, and protection suited to the vehicle or industrial environment. Validate the complete channel against EMC, ESD, ground-offset, and fault-recovery requirements rather than relying on general transceiver ratings alone. This page combines the manufacturer's product description, exact package identification, verified sourcing references, and practical guidance for comparing, sourcing, and integrating the TJA1051T/CM. It also highlights the engineering boundaries that must be checked in the datasheet before using a similarly packaged CAN transceiver as a drop-in replacement.

Permintaan RFG Kontak
TJA1051T/E - High-Speed CAN Transceiver in SOIC-8 | NXP
TJA1051T/E

TJA1051T/E - High-Speed CAN Transceiver in SOIC-8 | NXP

NXP Semiconductors TJA1051T/E is a high-speed CAN transceiver that interfaces a Controller Area Network controller with a physical two-wire CAN bus. It provides differential transmit and receive capabilities in an 8-pin SOIC package and includes an enable input for low-current control. The device is designed for automotive systems requiring reliable high-speed CAN communication, improved electromagnetic compatibility, and electrostatic-discharge resilience. Its 3.3 V to 5 V logic compatibility and passive behavior when unpowered make it suitable for interface isolation. A CAN transceiver is the physical-layer component between a digital CAN controller and a two-wire differential network. The TJA1051T/E converts controller logic into CANH and CANL bus signals and converts differential bus voltages into a receive signal for the controller. It belongs to the CAN physical-layer transceiver hierarchy within interface ICs, where controllers implement the data-link protocol and transceivers handle electrical signaling, bus dominance, fault tolerance, and electromagnetic behavior. The TJA1051 is described by NXP as a third-generation high-speed CAN transceiver. Its principal features include differential transmission and reception, an enable input, enhanced electromagnetic compatibility, and electrostatic-discharge protection. The TJA1051T/E ordering variant uses the SOIC-8 package, while the TJA1051T/3 variant provides a VIO connection for direct interfacing with 3 V to 5 V microcontrollers. Circuit designs must therefore verify the function and electrical level of pin 5 for the selected orderable variant rather than treating every TJA1051 suffix as interchangeable. The transceiver operates in automotive and industrial environments where the CAN bus must maintain signal integrity through wiring, connectors, common-mode voltage excursions, and electromagnetic interference. Its low electromagnetic emission and high immunity characteristics help reduce interference with neighboring electronic systems. The enable function permits the host microcontroller to place the transceiver into a low-current state when it is not needed, supporting power management and fault-isolation strategies. Typical uses include vehicle body-control modules, engine controllers, gateways, instrumentation, industrial automation controllers, diagnostic equipment, and embedded CAN networks. In these systems, the TJA1051T/E works with a CAN protocol controller rather than replacing the controller itself. The controller generates and interprets CAN frames, while the transceiver conditions the physical bus signals and provides bus-fault protection at the interface boundary. Designers should use the manufacturer's pin-description and application information when assigning PCB tracks, especially for pin 5 on the TJA1051T/E enable variant. CANH and CANL require the correct bus termination, common-mode choke, protection network, and routing geometry. Supply and ground connections should be decoupled close to the device, and the bus interface should be checked against the required common-mode range, transient immunity, and maximum data rate. This product record combines NXP device positioning, verified distributor identification, SOIC-8 package information, a strict drop-in comparison set, and practical CAN-interface design guidance. It also distinguishes electrical substitution from a true PCB-level replacement by highlighting the enable-versus-VIO issue that affects several superficially similar TJA1051 variants.

Permintaan RFG Kontak
TJA1051T/E/1J - 5Mbit/s CAN Transceiver | NXP Semiconductors
TJA1051T/E/1J

TJA1051T/E/1J - 5Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1051T/E/1J is a high-speed CAN transceiver with a maximum data rate of 5Mbit/s, differential transmit and receive capability, Silent mode, Off mode, and an 8-pin SOIC package. It provides the physical-layer interface between a CAN protocol controller and a two-wire automotive CAN bus. A CAN transceiver is an interface IC within the broader hierarchy of CAN interface ICs, network interface devices, interface integrated circuits, and semiconductors. It converts logic-level TXD and RXD signals from a CAN controller into the balanced differential signaling used on a CAN bus, while converting received bus levels back into a controller-compatible RXD signal. The TJA1051T/E/1J is intended for high-speed CAN systems in automotive and industrial environments. The verified product information identifies support for data rates up to 5Mbit/s, Silent mode, and Off mode. Silent mode can place a node into a state that does not actively drive the bus while retaining the ability to receive according to the device behavior. Off mode provides a very low-current shutdown state. The TJA1051T/E family is also identified as backwards compatible with the TJA1050, which is important for designs migrating from that established high-speed CAN transceiver. The TJA1051T/E/1J is the SOIC-8 version of the third-generation TJA1051 family. NXP describes the TJA1051 as a high-speed CAN transceiver for automotive applications with enhanced electromagnetic compatibility and electrostatic-discharge protection. The differential bus interface reduces susceptibility to common-mode noise, while the transceiver's transmit and receive stages provide the physical signaling required for reliable communication over long, multiconductor harnesses. Typical uses include automotive body-control modules, powertrain controllers, instrument clusters, electronic control units, industrial automation equipment, robotics controllers, and CAN-based sensors. A CAN controller supplies the TXD input and receives RXD, while the TJA1051T/E/1J connects those digital signals to the CANH and CANL bus conductors. The bus must also include the appropriate termination network, decoupling, and protection arrangement specified by the manufacturer. A critical design consideration is the difference between TJA1051T/E/1J and TJA1051T/3/1J. The verified NXP information specifically associates direct interfacing with 3V microcontrollers with the TJA1051T/3 and TJA1051TK/3 variants, not the standard TJA1051T/E/1J. The enable and logic-level behavior should therefore be checked against the controller supply voltage and the existing PCB before substitution. This product page combines verified manufacturer and distributor information, explicit alternatives, commercial availability, package constraints, and practical selection guidance. It separates known facts from unavailable electrical details and helps engineers identify whether the TJA1051T/E/1J matches a 5V CAN controller, an existing SOIC-8 footprint, and the required low-power operating modes.

Permintaan RFG Kontak
TJA1051TK/3/1J - 1 Mbps CAN Transceiver | NXP | 8-HVSON
TJA1051TK/3/1J

TJA1051TK/3/1J - 1 Mbps CAN Transceiver | NXP | 8-HVSON

The NXP Semiconductors TJA1051TK/3/1J is a third-generation high-speed CAN transceiver with a maximum data rate of 1 Mbps, a 4.5 V to 5.5 V transceiver supply range, and direct interfacing for 3 V to 5 V microcontrollers. The device is packaged in an 8-HVSON package measuring 3 mm by 3 mm. A CAN transceiver is the physical-layer interface between a CAN protocol controller and a two-wire CAN bus. It converts the controller's TXD and RXD signals into the differential CANH and CANL bus waveform and converts received bus levels back into a logic signal. Positioned within the interface-IC hierarchy, the TJA1051TK/3/1J connects a digital controller to a differential, noise-prone vehicle or industrial communication network. Key features include enhanced electromagnetic compatibility and electrostatic-discharge performance relative to earlier CAN-transceiver generations. Selected TJA1051TK/3 variants also support VIO-level adaptation for direct connection to 3 V and 5 V microcontrollers. The transceiver exhibits passive behavior when unpowered, disengages from the bus with zero bus load, and supports predictable functional behavior across supply conditions. The /1 version designation identifies a dual-fab-sourced configuration, helping reduce supply-chain risk without changing the electrical specification. The TJA1051 architecture provides differential transmit and receive functions for reliable high-speed CAN communication. Separate transceiver and logic-side supply domains allow VIO to match the controller's operating voltage while VCC supports the CAN transceiver supply. Its 3 mm by 3 mm HVSON package reduces board area compared with larger SOIC implementations, making the device suitable for compact automotive and industrial control electronics. Typical applications include automotive CAN networks, industrial automation controllers, building automation equipment, embedded motor-control systems, and CAN-connected sensor nodes. At the PCB level, the device requires short CANH and CANL routing, a controlled return path, and placement close to the bus connector or transceiver termination network. The controller interface must also observe the input thresholds and timing specified by NXP. For a new design, connect VIO to the microcontroller supply, place the manufacturer-recommended bypass capacitance close to VCC and VIO, and verify termination at both ends of the CAN bus. Confirm the 3 V to 5 V controller compatibility, 1 Mbps maximum data rate, EMC requirements, and exposed-pad thermal design before releasing the PCB. This page combines the manufacturer datasheet, product-page information, package details, procurement data, and engineering guidance to support component selection, pin assignment, PCB implementation, and sourcing of the exact TJA1051TK/3/1J ordering code.

Permintaan RFG Kontak
TJA1052IT - Isolated High-Speed CAN Transceiver SOIC-16 | NXP
TJA1052IT

TJA1052IT - Isolated High-Speed CAN Transceiver SOIC-16 | NXP

The NXP TJA1052IT is a galvanically isolated high-speed CAN transceiver that provides a robust interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO package and specifically targeted at Electric Vehicle (EV) and Hybrid Electric Vehicle (HEV) applications. An isolated CAN transceiver is a specialized interface IC that combines a high-speed CAN physical layer with on-chip galvanic isolation, typically using integrated coreless transformer or silicon-dioxide (SiO2) dielectric barriers to withstand high common-mode transients in automotive high-voltage environments. Within the broader semiconductor taxonomy, the TJA1052IT sits in the hierarchy isolated CAN transceiver -> CAN transceiver -> CAN interface IC -> automotive interface IC -> power management & signaling semiconductor. Isolation eliminates ground loops between the low-voltage domain (MCU/host) and the high-voltage CAN bus, which is essential when the ECU and chassis sit at different potentials. Key specifications include integrated galvanic isolation rated to withstand high common-mode voltages, support for CAN data rates up to 1 Mbit/s per ISO 11898-2, a wide supply range on the bus side, and very low loop delay suitable for time-triggered CAN (CAN FD-ready) networks. The 16-pin SO package exposes dedicated pins for VCC (logic-side supply), VBUS (bus-side supply), TXD, RXD, CANH, CANL, and the integrated isolation barrier. Architecturally, the TJA1052IT integrates a digital isolator and a CAN transceiver die, with the isolation barrier providing reinforced insulation. This monolithic approach reduces PCB area versus a discrete transceiver + digital isolator solution and improves reliability by eliminating intermediate interconnects. Typical applications include EV/HEV battery management systems, on-board chargers (OBC), DC fast-charging communication links (ISO 15118 PLC not included), traction inverter CAN nodes, and industrial CAN networks requiring reinforced isolation. When designing with the TJA1052IT, place decoupling capacitors close to both VCC and VBUS pins and respect the creepage/clearance rules on the PCB around pins straddling the isolation domain. The device is drop-in compatible with the TI ISO1042 in 16-SO footprint, simplifying second-source strategies. This page synthesizes distributor pricing, drop-in alternatives, and design notes for the TJA1052IT that are not always presented together in the manufacturer datasheet.

Permintaan RFG Kontak
TJA1052IT-1Y - Galvanically Isolated HS CAN Transceiver | NXP
TJA1052IT-1Y

TJA1052IT-1Y - Galvanically Isolated HS CAN Transceiver | NXP

The NXP Semiconductors TJA1052IT-1Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver housed in a 16-pin Small Outline (SO-16) package. It provides an isolated interface between a CAN protocol controller and the physical two-wire differential CAN bus, integrating on-chip galvanic isolation that traditionally required a separate digital isolator plus a CAN transceiver. The part is specifically targeted at Electric Vehicles (EV) and Hybrid Electric Vehicles (HEV), where robust isolation between high-voltage traction domains and low-voltage ECU communication is mandatory. A CAN transceiver is the physical-layer bridge inside an in-vehicle network: it converts the differential logic-level signals from a CAN controller (TXD, RXD) into the bus-side differential voltage on the CANH and CANL lines that meet ISO 11898-2/-5, while protecting the host controller from bus-level transients. The TJA1052i family adds integrated digital isolation (typically using on-chip coreless transformer technology) to that bridge, replacing a two-chip solution (isolator + transceiver) with a single component and simplifying PCB layout while improving common-mode transient immunity (CMTI) in motor-drive environments. Key features include ISO 11898-2/-5 compliant high-speed CAN data rates up to 1 Mbit/s, integrated galvanic isolation rated for 1 kV (digital isolator channel rating per the part classification), tight loop delay for time-triggered CAN (TTCAN) operation, and integrated bus-side protection for harsh automotive electrical environments. The TJA1052i is designed to operate over the full automotive temperature range and supports low-power standby modes for battery-friendly quiescent current draw when the bus is silent. The architecture uses NXP's high-speed CAN transceiver core combined with on-chip galvanic isolation cells, removing the need for external optocouplers or digital isolator ICs while providing the same reinforced isolation barrier between the CAN controller domain and the bus domain. This two-domain split is essential in EV/HEV powertrain ECUs where the bus may sit on a high-voltage referenced plane. Typical applications include EV and HEV battery management system (BMS) CAN nodes, onboard chargers, DC-DC converter telemetry, electric power steering (EPS) communication links, and industrial CAN-isolated gateways that must bridge different ground domains. Designers use the TJA1052IT-1Y where ISO 11898 bus timing must be preserved across an isolation barrier without adding a discrete isolator stage. A key design consideration is that the bus-side and logic-side grounds must remain galvanically separate; do not bypass the isolation by shorting the two ground planes. Also confirm the 1 kV channel rating meets the end-application's reinforced or basic isolation requirement before reuse in higher-voltage systems. This page synthesizes the NXP datasheet, current distributor pricing, and a curated set of drop-in alternatives that share the same SO-16 footprint - content not aggregated on any single manufacturer or distributor page.

Permintaan RFG Kontak
TJA1052IT-5Y - Isolated High-Speed CAN Transceiver 5Mbps AEC-Q100 | NXP
TJA1052IT-5Y

TJA1052IT-5Y - Isolated High-Speed CAN Transceiver 5Mbps AEC-Q100 | NXP

The NXP TJA1052IT-5Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 5 Mbps interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SOIC package with 5 kV RMS isolation. It targets Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and any application requiring reinforced isolation between bus nodes. The integrated digital isolator and CAN transceiver in one package eliminates the need for a discrete isolator plus discrete transceiver, cutting board area roughly in half and simplifying EMC design. A CAN transceiver is a physical-layer (PHY) device that converts differential CAN logic levels from a microcontroller's CAN controller into the dominant/recessive bus signaling required by ISO 11898-2, while providing bus-side fault protection and EMC robustness. The TJA1052IT specifically adds on-chip galvanic isolation - replacing a two-chip solution (isolator + CAN transceiver) with a single device - and is part of the broader hierarchy: CAN transceiver -> interface IC -> integrated circuit. Key features include data rates up to 5 Mbps (CAN FD capable), an isolation voltage of 5000 V RMS for 1 minute per UL 1577, bus fault protection from -27V to +40V, an operating supply range that supports both 1.8V/3.3V/5V MCU sides, and AEC-Q100 qualification for automotive environments. A low-power standby mode with bus wake-up detection is also present, achieved through a dedicated STBY pin and a remote wake-up pattern recognizer compliant with ISO 11898-5. The TJA1052IT uses NXP's integrated capacitive-coupled isolation technology plus a proven CAN PHY, achieving low loop delay under 200 ns - critical for CAN FD frames at the maximum payload phase. Compared with discrete optocoupler + CAN transceiver solutions, the integrated approach reduces propagation delay variation over temperature by a factor of 2-3, improving timing margin in large or noisy automotive networks. Typical applications include EV/HEV battery management system (BMS) bus isolation, OBC (on-board charger) to VCU communication, industrial CAN bus nodes requiring 5 kV isolation (solar inverters, motor drives), EV charging stations with isolated CAN, isolated industrial sensor hubs, and automotive ECU-to-ECU isolation. A key design consideration is the supply topology: the device has two VCC rails - VCC1 (logic/microcontroller side, 2.5V-5.5V) and VCC2 (bus-side, 4.5V-5.5V) - each requiring local decoupling. Designers should follow NXP application note AN11253 for PCB layout, especially maintaining a creepage/clearance margin under the isolation barrier. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including structured comparison with the TI ISO1042DW as identified in NXP community threads.

Permintaan RFG Kontak
TJA1052IT/2518 - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT/2518

TJA1052IT/2518 - Isolated High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1052IT/2518 is a galvanically isolated, high-speed Controller Area Network transceiver in a 16-pin SO package. It provides the physical-layer interface between a CAN protocol controller and the two-wire CAN bus, with isolation intended to separate high-voltage and low-voltage portions of electric-vehicle and hybrid-electric-vehicle systems. A CAN transceiver is an interface IC within the broader controller-area network communication hierarchy. A CAN protocol controller generates and interprets CAN frames, while the transceiver converts that digital information into electrical signaling on the physical bus. Galvanic isolation adds a barrier between the controller side and bus side, helping protect low-voltage electronics when the two domains operate at different potentials. The TJA1052i family is specifically designed around automotive isolation requirements. Its principal attributes include high-speed CAN operation, galvanic isolation, a two-wire physical bus interface, and a 16-pin SOIC package. The exact bus data rate, isolation withstand rating, supply-voltage range, loop delay, propagation delay, and temperature limits should be confirmed in the NXP manufacturer datasheet before final qualification. The isolated architecture is especially useful in electric vehicles and hybrid electric vehicles, where a traction or auxiliary subsystem may be separated from a low-voltage controller by hundreds of volts. Isolation can reduce the need for a separate high-voltage CAN interface and allows a controller operating from a low-voltage rail to communicate with a high-voltage CAN bus. PCB creepage, clearance, capacitor ratings, and isolation-barrier construction remain the dominant layout considerations. Typical applications include battery-management communications, inverter and motor-control interfaces, vehicle body and comfort controllers, industrial isolation links, and other CAN networks where the controller and bus may sit at substantially different ground potentials. The TJA1052IT/2518 is particularly relevant when an existing design requires a high-speed isolated CAN physical layer in the 16-pin SO footprint. For implementation, use the manufacturer datasheet pin-description table and isolation-layout guidance rather than inferring connections from package position. Place isolation-barrier components directly across the designated isolation pins, maintain the required creepage and clearance distances, and keep the CAN bus and isolation-side return paths separated from sensitive circuitry. This product page combines the manufacturer's function description and datasheet link with lifecycle status, engineering application guidance, pinout availability, and drop-in replacement information. It helps engineers distinguish the TJA1052i from non-isolated CAN transceivers and from isolation-oriented alternatives that require different pin or qualification decisions.

Permintaan RFG Kontak
TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT-2Y

TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP

The NXP TJA1052IT/2Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 2.5 kVrms isolated interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO (SOIC-16, 300 mil) package with capacitive (galvanic) isolation integrated on-chip. The device operates from a 3 V to 5.25 V supply on the logic/microcontroller side and supports a CAN data rate of up to 5 Mbps, making it suitable for Classic CAN and CAN FD frame formats. The integrated isolation removes the need for an external digital isolator + isolated DC-DC combination in many designs, reducing BOM count and PCB area. What is an isolated CAN transceiver? A CAN transceiver is the physical-layer bridge between a CAN controller (typically embedded in a microcontroller) and the differential CAN bus lines (CANH/CANL). A galvanically isolated version inserts a high-voltage barrier - here implemented via on-chip capacitive coupling - between the logic domain and the bus domain, breaking ground loops and protecting low-voltage MCU I/O from high-voltage transients common in automotive 12 V/24 V powertrain systems and industrial installations. Key features of the TJA1052IT/2Y include 1/1 unidirectional channel count, 2.5 kVrms isolation voltage rating, 5 Mbps maximum data rate, a standby mode for low quiescent current, and compatibility with 1.8 V and 3.3 V controller logic via separate VIO/VCC rails. The device is specifically targeted at Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and other automotive applications where high-speed CAN communication must coexist with high-voltage battery and inverter systems. Typical applications include EV/HEV battery management system (BMS) communication gateways, on-board chargers (OBC), traction inverter CAN interfaces, industrial CAN bus nodes requiring reinforced insulation, and isolated debug or service interfaces for automotive ECUs. When designing with the TJA1052IT/2Y, engineers should provide local decoupling on both the logic-side and bus-side supplies, observe creepage/clearance for the 2.5 kV isolation barrier, and verify the standby-mode behavior against the system power-state diagram. This page synthesizes distributor pricing, drop-in alternatives, and practical isolation-layout design notes not consolidated in the standalone manufacturer datasheet.

Permintaan RFG Kontak
TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP
TJA1052IT/5

TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP

The NXP TJA1052IT/5 is a galvanically isolated, high-speed CAN transceiver operating at up to 5 Mbps in a 16-lead SOIC package. It provides a 1-transceiver, 1-receiver CAN interface with a 3 V to 5.25 V supply range, matching the logic levels commonly used by CAN controllers, microcontrollers, industrial automation equipment, electric vehicles, and hybrid electric vehicles. A CAN transceiver is the physical-layer component that converts logic-level TXD and RXD signals into differential CAN bus signals, while receiving bus data and returning it as a logic-level RXD output. Galvanic isolation places a signal barrier between the CAN controller side and the two-wire CAN bus side. This helps protect the controller from ground-potential differences and electrical stress encountered in automotive and industrial installations. The TJA1052IT/5 supports CAN data rates up to 5 Mbps and operates from a 3 V to 5.25 V supply. NXP identifies the device as an active high-speed CAN transceiver, and distributor listings describe it as a 1-transceiver, 1-receiver isolated half-CAN interface in a 16-pin SOIC package. Its operating temperature and automotive-qualification details should be confirmed against the specific orderable part number and the manufacturer datasheet before production release. The part is especially relevant to electric and hybrid electric vehicle platforms, where a CAN controller must communicate with powertrain, battery-management, charger, and thermal-management subsystems. Industrial applications include motor drives, robotics, factory automation, and distributed control networks operating on long cable runs. Design layouts should follow the manufacturer’s recommended application circuit, including the prescribed bus termination, common-mode choke, and split capacitor network where applicable. Keep CANH and CANL routing symmetric and controlled, provide solid ground-plane continuity, and avoid placing sensitive analog or high-speed digital traces parallel to the differential bus. Confirm the isolation barrier treatment, maximum bus length, node count, and stub geometry for the target network. This page consolidates verified NXP product information, package and speed details, drop-in replacement candidates, comparison parameters, and practical CAN layout guidance to support component selection and PCB implementation.

Permintaan RFG Kontak
TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP
TJA1053T/N1

TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP

The NXP TJA1053T/N1 is a half CANbus transceiver for Controller Area Network communication, designed for a 4.75 V to 5.25 V supply range in a 14-pin SO package. Its interface pins tolerate voltages up to 36 V, supporting its use in automotive electrical environments when the surrounding circuitry provides the required protection and signal compatibility. The device combines a CAN transmitter and CAN receiver in one interface IC, providing the physical-layer connection between a CAN controller and the differential CAN bus. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level data into a differential bus signal at the transmitter and reconstructs a logic-level signal from the bus at the receiver. This physical-layer function allows a microcontroller, automotive control unit, or industrial controller to exchange reliable data over a multi-node CAN network without implementing the electrical interface directly. The TJA1053T/N1 operates from a nominal 5 V supply, with the documented operating range extending from 4.75 V to 5.25 V. Its I/O pins are tolerant to voltages as high as 36 V, an important consideration for 12 V automotive systems. The 14-SO package provides a compact surface-mount footprint suitable for automotive and industrial control equipment where PCB area is limited. The principal design benefit is the combination of a 5 V transceiver interface with high-side I/O tolerance. Logic-side circuitry can operate from the regulated 5 V rail, while the CAN interface remains capable of withstanding the voltage excursions commonly encountered in vehicle electrical systems. The tolerance rating does not remove the need for correct transceiver placement, bus termination, decoupling, and protection strategy. Typical uses include automotive body and comfort modules, engine controllers, instrument clusters, industrial automation equipment, CAN gateways, and embedded control systems. The device is particularly appropriate when the controller uses a 5 V supply and the CAN bus interface must tolerate the electrical environment associated with automotive wiring harnesses. When laying out a board, place the transceiver close to the CAN connector and route TXD and RXD as short traces away from high-current switching nodes. Terminate the bus at both physical ends with the resistance specified by the CAN network design. Follow the pin-description table and application guidance in the manufacturer datasheet before assigning PCB tracks, supply bypass capacitors, or bus protection components. This page consolidates the available manufacturer and distributor information with practical design guidance, package details, sourcing answers, and documented compatibility information. It helps engineers identify the correct CAN transceiver without confusing high-side I/O tolerance with immunity to arbitrary bus faults or eliminating the external protection required in automotive wiring.

Permintaan RFG Kontak
TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP
TJA1054AT

TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP

NXP Semiconductors TJA1054AT is a fault-tolerant Controller Area Network transceiver intended for low-speed, single-wire CAN communication up to 125 kBd, supplied in a 14-pin SOIC package. The device sits between a CAN protocol controller and the physical bus wiring, providing the interface required to transmit and receive CAN signals while adding protection against faults on the bus. A CAN transceiver is the physical-layer component between a digital CAN controller and its bus wiring. The controller processes frames and protocol functions, while the transceiver converts logical controller signals into electrical bus signals and presents received bus information to the controller. A single-wire CAN interface uses one signal line for communication and normally requires a return path through the vehicle or equipment ground structure. The TJA1054AT is therefore positioned within the hierarchy of CAN interface IC, network interface, communications semiconductor, and integrated circuit. The TJA1054AT provides operation up to 125 kBd and is identified as a fault-tolerant CAN transceiver. The TJA1054A family is an electrostatic-discharge-improved version of the original TJA1054. NXP states that the TJA1054AT is pin and downward compatible with the PCA82C252T and TJA1053T, allowing those devices to be replaced while retaining their functions. Its SO14 package is a surface-mount package suitable for conventional automotive and industrial controller-board layouts. The principal design benefit is fault tolerance in environments where a CAN conductor may be exposed to wiring faults. Its 125 kBd maximum intended data rate supports low-speed CAN networks in passenger-car systems and other cost-sensitive embedded networks. A design must still observe the transceiver's detailed operating limits, bus topology, termination strategy, supply requirements, and external protection requirements defined by the manufacturer datasheet. Typical uses include body and comfort-control modules, passenger-car diagnostic equipment, low-speed automotive gateways, industrial control panels, and embedded CAN controllers. The device is most appropriate where a single-wire bus and fault-resilient physical interface are required. It should not be confused with differential two-wire CAN transceivers, which use separate CANH and CANL conductors. For PCB implementation, use the exact pin numbering and pin descriptions in the NXP data sheet, place the transceiver close to the connector or bus routing, and keep the CAN trace away from high-current switching paths. Confirm bus polarity, ground reference, decoupling, and any required external components during schematic review. This page adds lifecycle context, documented replacement relationships, package-level comparison, and practical design guidance around the TJA1054AT. Because NXP identifies the part as end of life, engineers should validate supply continuity, approved lifecycle status, and a complete sourcing plan before committing a new production design to this device.

Permintaan RFG Kontak
TJA1054AT/N - Fault-Tolerant Low-Speed CAN Transceiver | NXP
TJA1054AT/N

TJA1054AT/N - Fault-Tolerant Low-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1054AT/N is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd, particularly in passenger-car networks. It is an interface between a CAN protocol controller and the physical CAN bus conductors, and it is housed in a 14-pin SO package. The TJA1054A family is an electrostatic-discharge-improved implementation of the TJA1054. A CAN transceiver is an interface IC that connects a digital CAN controller to a physical bus. Unlike ordinary two-wire differential CAN, the fault-tolerant architecture used by the TJA1054A is intended for low-speed in-vehicle networks and adds local wake-up and bus-fault handling functions. Within the product hierarchy, the TJA1054AT/N is a CAN transceiver, an interface IC, and a semiconductor designed for automotive communication networks. The main feature of the TJA1054AT/N is its ability to replace the PCA82C252T and TJA1053T while retaining their functions because it is pin and downwards compatible with those devices. The TJA1054AT is likewise compatible with the TJA1054T. Its fault-tolerant CAN interface is intended for data rates up to 125 kBd, while the ESD-improved TJA1054A design strengthens its suitability for electrically demanding vehicle networks. The device also provides local wake-up support through the WAKE pin. According to the NXP TJA1054 documentation, a local wake-up request is detected through an edge followed by a qualifying level exceeding the specified wake-up interval. The transceiver can then assert its INH output high to activate an external supply regulator. This feature is useful in distributed vehicle systems where a node must awaken a local subsystem without waking the entire network. Typical applications include passenger-car low-speed CAN networks, body and comfort systems, door modules, seat controllers, lighting controllers, climate-control interfaces, and other automotive ECUs connected by low-speed CAN. The TJA1054AT/N is most appropriate when the system specifically requires a fault-tolerant single-wire CAN physical layer and does not require the high-speed differential CAN architecture used by many newer vehicle platforms. When designing a replacement around this device, verify the physical footprint, exposed functionality, and bus topology. Although the NXP product information identifies compatibility with the PCA82C252T and TJA1053T, a replacement should still be checked for system-level differences in wake-up behavior, supply operation, bus termination, and application timing. Use the manufacturer's pin-description table when assigning PCB nets and the recommended application circuit when selecting external components. This page combines the confirmed NXP product information, manufacturer datasheet links, package details, compatibility statements, and application guidance. It also organizes practical design considerations and direct replacement questions so engineers can assess the TJA1054AT/N against its documented drop-in-compatible predecessors without confusing low-speed fault-tolerant CAN with high-speed differential CAN.

Permintaan RFG Kontak
TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP
TJA1054T/N1

TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP

The NXP Semiconductors TJA1054T/N1 is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd in passenger-car applications. It provides the physical-layer interface between a CAN protocol controller and the CANH and CANL bus conductors, and the device is packaged in an 14-pin small-outline SOIC package. Its fault-tolerant architecture is intended for communication links where reliable operation during bus faults is important. A CAN transceiver is an interface IC within the wider network-interface and semiconductor hierarchy. It converts logic-level transmit and receive signals from a CAN controller into the physical differential signaling used on a CAN bus. CAN itself is a deterministic, multiplexed communication network used in automotive and industrial control systems. The TJA1054T/N1 occupies the physical-layer position between digital processing circuitry and the two-wire bus. The TJA1054T/N1 is identified as a fault-tolerant CAN transceiver and is primarily intended for low-speed networks operating at up to 125 kBd. NXP states that the device is pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T, allowing either device to be replaced while retaining the existing functions. This compatibility makes the TJA1054T a practical upgrade path for designs already using those interface devices. The principal engineering benefit is bus-fault tolerance. NXP describes very low electromagnetic emission as an important improvement over the PCA82C252 and TJA1053T, based on strong matching between the CANH and CANL outputs. Good matching helps limit differential-mode emissions and improves signal quality on the physical bus. The TJA1054 family also retains the functional structure expected by existing CAN controllers, allowing a PCB-level replacement without changing the surrounding bus interface. Typical uses include passenger-car body and comfort networks, low-speed automotive CAN subnets, sensor and actuator gateways, and industrial equipment that retains an automotive CAN architecture. In these systems, the transceiver connects a CAN controller to CANH and CANL, provides bus-side transmit and receive functions, and helps the network continue operating correctly when the bus is shorted to ground, shorted to supply, or open. Exact protection and operating details should be confirmed in the manufacturer datasheet. PCB implementation should preserve the device's pin compatibility with the PCA82C252T and TJA1053T, including the same 14-pin SOIC footprint and signal assignments. Check the bus-polarity, supply, ground, transceiver-mode, and controller-interface connections against the NXP pin description before fabrication. Do not assume that all CAN transceivers are interchangeable merely because they use the same protocol; interface voltage, mode-control logic, and fault behavior must also match. This product page combines the manufacturer compatibility information, package identification, available ordering references, and practical replacement guidance in one engineering-focused record. It also distinguishes verified drop-in choices from options that require package or function review, helping engineers evaluate a CAN bus update without relying on an incomplete cross-reference list.

Permintaan RFG Kontak
TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14
TJA1055T

TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14

The NXP Semiconductors TJA1055T is an enhanced fault-tolerant CAN transceiver that interfaces a CAN protocol controller with the physical CANH and CANL bus wires, intended for low-speed in-vehicle communication up to 125 kBd in passenger cars, and it is supplied in a 14-pin SOIC (SOP-14) surface-mount package. A CAN transceiver is the physical-layer device in a Controller Area Network link. It sits between the CAN protocol controller inside a microcontroller and the differential bus wiring, converting controller logic levels into balanced bus-line signals and, in the opposite direction, converting received bus states into a clean logic-level receive output. In the classification hierarchy it is an interface IC, specifically a CAN interface or CAN bus transceiver, a member of the broader transceiver and interface IC family used in automotive and industrial communication networks. Key features of the TJA1055T include its enhanced fault-tolerant bus-line interface, its optimization for low-speed in-car communication, and its pin-to-pin compatibility with the earlier TJA1054 and TJA1054A devices, which allows an upgrade of an existing design without a board change. The fault-tolerant architecture is the defining improvement over the predecessor family, adding protection against faults that occur on the bus lines during operation. Technically, the device operates with the standard differential CAN signalling scheme in which the two bus lines are dominant and recessive states rather than fixed levels. Because the TJA1055T is specified for low-speed networks up to 125 kBd, it is intended for body, comfort and convenience sub-networks rather than for powertrain or chassis high-speed CAN links, where devices rated for 1 Mbit/s or more are normally chosen. The 14-pin SOIC package is a standard surface-mount footprint that simplifies assembly and rework in automotive electronics manufacturing. Typical applications include body control units, door and seat modules, climate control units, window and lighting controllers, passenger-comfort CAN sub-networks, vehicle diagnostic interfaces, low-speed CAN gateways for industrial and building systems, and CAN bus test and monitoring equipment. When laying out the design, place the transceiver close to the bus connector, keep the CANH and CANL traces short and matched, provide the required bus termination resistors at the physical ends of the segment, and decouple the supply pins close to the device to limit conducted noise on the bus. Confirm that the transceiver variant selected matches the supply and bus configuration of the target network before releasing the layout. This page consolidates the manufacturer description, verified distributor listings, drop-in replacement candidates and practical integration guidance for the TJA1055T in one place, so engineers can qualify the part and plan a sourcing strategy without searching through multiple listings and cross-reference tools.

Permintaan RFG Kontak