Produk (46.000+)

MAX3232ESE+T - 3.0-5.5V RS-232 Transceiver, 1Mbps, 16-SOIC | Maxim
MAX3232ESE+T

MAX3232ESE+T - 3.0-5.5V RS-232 Transceiver, 1Mbps, 16-SOIC | Maxim

The Maxim Integrated MAX3232ESE+T (now under Analog Devices / Maxim Integrated) is a 3.0 V to 5.5 V, true RS-232 transceiver with two drivers and two receivers, supporting data rates up to 1 Mbps in a 16-pin SOIC (NSOIC, 0.150 inch) package. It operates from a single 3.0 V to 5.5 V supply and integrates a high-efficiency charge pump with four external 0.1 µF capacitors to generate ±5.5 V RS-232 levels from the input rail. The device is offered on tape-and-reel (the +T is the reel indicator). An RS-232 transceiver is a line driver/receiver IC that translates logic-level (TTL/CMOS) signals from a microcontroller or UART to the +/-5 V to +/-15 V signaling required by the EIA/TIA-232 standard, and vice versa. RS-232 transceivers sit between the data terminal equipment (DTE) and data communication equipment (DCE) and form part of the physical layer of the UART/serial interface family, alongside RS-422 and RS-485 transceivers for longer-distance differential links. Key features of the MAX3232ESE+T include 1 Mbps guaranteed data rate (250 KB/s in the older 160 ns slew-rate version), low supply current of 1 mA typical, an enhanced ESD protection of +/-15 kV HBM on the RS-232 bus pins, and true RS-232 output swing with automatic power-down shutdown. It also provides a low-dropout transmitter output stage so true RS-232 levels are maintained even when VCC drops to 3.0 V. The architecture uses a regulated dual charge pump and four small 0.1 µF ceramic capacitors, eliminating the bulky +/-12 V rails and 1 µF / 10 µF pump capacitors required by classic MAX232 designs. This shrinks the BOM and PCB area and enables portable 3.3 V-only systems to drive full-spec RS-232 links without auxiliary supplies. The part is pin-compatible with the industry-standard MAX232 family. Typical applications include battery-powered serial ports on portable equipment, embedded UART-to-RS-232 bridges on 3.3 V microcontroller boards (e.g. PIC32 and STM32 designs), industrial control and point-of-sale terminals, GPS receiver interfaces, and legacy PC COM-port replacements. Designers of lithium-ion-powered products appreciate the 1 mA supply current. When designing with this part, place the four 0.1 µF charge-pump capacitors (C1-C4) as close as possible to the package and keep the RS-232 trace lengths short. Decouple VCC with 0.1 µF in parallel with 1 µF, and add a series ferrite or TVS if the link will see ESD events beyond the +/-15 kV HBM rating. Note that MAX3232ESE (slew-rate-limited, 160 ns version) is the 250 KBps part; the MAX3232E and 'E' suffix are typically the 1 Mbps variants - verify the exact suffix on the order code before committing to a 1 Mbps design. This page synthesizes distributor pricing, drop-in cross-brand alternatives (TI TRSF3232, Exar SP3232, TI TRS2023), application context not found in the datasheet alone, and an engineering-grade pinout to support sourcing, design-in, and drop-in substitution decisions.

Permintaan RFG Kontak
MAX3232ESE+TG035 - 2x2 RS-232 Transceiver, 3-5.5V | Maxim
MAX3232ESE+TG035

MAX3232ESE+TG035 - 2x2 RS-232 Transceiver, 3-5.5V | Maxim

The Analog Devices Inc./Maxim Integrated MAX3232ESE+TG035 is a low-power, true RS-232 transceiver with 2 drivers and 2 receivers, operating from a 3.0V to 5.5V supply at data rates up to 1Mbps, housed in a 16-pin SOIC (N) package using only four external 0.1uF capacitors. An RS-232 transceiver is an interface IC that converts TTL/CMOS logic levels (typically 0-5V or 0-3.3V) into the RS-232 voltage convention (nominally +/-5V to +/-15V) and back, allowing microcontrollers to communicate with legacy serial ports, modems, and industrial equipment. Within the signal-chain hierarchy it belongs to interface ICs -> drivers/receivers/transceivers -> line transceivers, sitting between the UART logic pin of a processor and the physical DB-9 serial connector. Key features include the wide 3.0V to 5.5V single-supply range that supports both 3.3V and 5V systems, guaranteed 250kbps operation with 3V/1uF load and up to 1Mbps minimum data rate under standard conditions, and the proprietary charge-pump architecture requiring only four 0.1uF external capacitors instead of the large 5uF capacitors of older generation devices. Technically, the device integrates dual charge pumps with cascaded voltage doublers and inverters to generate +5.5V and -5.5V rails internally from the logic supply. The E-suffix grade is specified for -40C to +85C operation. The drivers meet or exceed EIA/TIA-232 and V.28 requirements, and the receivers feature a 0.5V input threshold with 5V-tolerant operation and schmitt-trigger hysteresis for noise immunity. Typical applications include industrial fieldbus adapters, point-of-sale terminals, battery-powered instrumentation with DB-9 debug ports, and legacy PC serial maintenance interfaces. The TG035 suffix identifies the tape-and-reel packaging variant for automated pick-and-place assembly. Design consideration: use 0.1uF charge-pump capacitors rated at 16V or higher and place them close to the IC pins; larger capacitors (1uF) are only needed when running near the 1Mbps rate at 3.3V. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX3232EUE+ - 3.0-5.5V 1Mbps RS-232 Transceiver | Maxim
MAX3232EUE+

MAX3232EUE+ - 3.0-5.5V 1Mbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3232EUE+ is a 3.0 V to 5.5 V, low-power, true RS-232 transceiver with two transmitters, two receivers, and operation up to 1 Mbps in a 16-pin TSSOP package. Its dual charge-pump design generates the bipolar voltage levels required by RS-232 while allowing the device to operate from a single 3.0 V to 5.5 V supply. An RS-232 transceiver is an interface IC that converts between logic-level signals used by digital systems and bipolar voltage signals used by RS-232 links. It belongs to the interface IC category and connects host controllers, test equipment, industrial systems, and peripheral controllers through the EIA RS-232 standard. A dual transceiver supports two communication channels on one device while reducing board area and component count. The MAX3232EUE+ operates from 3.0 V to 5.5 V and supports data rates up to 1 Mbps. Its true RS-232 transmitter output stage uses low-dropout operation, while the internal dual charge pump requires only four external 0.1 uF capacitors. The 16-TSSOP package is suitable for compact surface-mount equipment, although its narrow lead pitch requires careful PCB assembly and soldering. The transceiver architecture separates the transmit and receive paths, allowing one side of the interface to remain active while the other handles incoming data. This makes the device suitable for systems with asynchronous serial links, local control ports, and communication with legacy RS-232 equipment. The single-supply implementation also simplifies power design in systems that do not provide a separate negative voltage rail. Typical applications include industrial controller serial ports, laboratory data acquisition, point-of-sale equipment, security systems, embedded instrument interfaces, and general-purpose RS-232 links. Systems requiring two serial channels can use the two transmitters and two receivers in one package. The 1 Mbps capability accommodates substantially faster links than the commonly used 115.2 kbaud RS-232 rate. When placing the device, position the four 0.1 uF charge-pump capacitors close to their associated pins and preserve the pinout shown in the manufacturer datasheet. Confirm cable-length limitations because higher baud rates reduce the practical distance supported by RS-232. The interface also needs appropriate protection and grounding when connected to exposed or industrial cabling. This page combines electrical specifications, package guidance, application fit, comparison data, and drop-in replacement information to support faster component selection and PCB implementation. It also identifies the key technical distinctions engineers should verify when considering another RS-232 transceiver.

Permintaan RFG Kontak
MAX3232EUE+T - Dual RS-232 Transceiver | Analog Devices
MAX3232EUE+T

MAX3232EUE+T - Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EUE+T is a dual RS-232 transceiver with two drivers, two receivers, and a dual charge-pump circuit, operating from 3.0 V to 5.5 V at data rates up to 1 Mbps in a 16-pin TSSOP package. It is designed for bidirectional asynchronous serial communication between modern digital systems and legacy RS-232 equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compliant voltage levels and restores RS-232 inputs to compatible logic levels. The MAX3232 belongs to the interface IC hierarchy, combining line drivers, line receivers, charge pumps, and protection functions in one device. Its charge-pump architecture supports true RS-232 operation from a single 3.0 V to 5.5 V supply without a separate negative supply rail. The device requires only four external 0.1 µF charge-pump capacitors. Its integrated dual charge pump generates the positive and negative voltages needed by the drivers, while the receiver side converts incoming serial data into CMOS-compatible signals. The MAX3232E family provides low power consumption, including approximately 300 µA typical quiescent current reported for the MAX3232EUE+T, making it suitable for equipment where both interface performance and operating efficiency matter. With two transmit and two receive channels, the transceiver can support two RS-232 ports or provide hardware flow-control signals alongside one primary data channel. Operation from 3.0 V to 5.5 V allows use with 3.3 V and 5 V logic systems. Its 16-pin TSSOP package supports compact surface-mount assemblies, while the stated data-rate capability of up to 1 Mbps suits higher-speed serial links, instrumentation, and industrial control equipment. Typical applications include industrial serial consoles, point-of-sale terminals, test and measurement equipment, barcode scanners, and embedded systems communicating with legacy RS-232 peripherals. The device is especially useful when the logic supply is 3.3 V but the attached peripheral still requires true bipolar RS-232 signaling. For a reliable layout, place all four 0.1 µF charge-pump capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog and high-speed digital traces. Confirm signal polarity, flow-control direction, and connector pin assignments during schematic review because the transmit and receive pins are dedicated rather than automatically interchangeable. This page combines the manufacturer's electrical and package information with same-family drop-in alternatives, application guidance, interface-design notes, and a parameter comparison. It is intended to help engineers identify the correct MPN, validate PCB compatibility, and implement a reliable RS-232 interface.

Permintaan RFG Kontak
MAX3232EWE+T - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EWE+T

MAX3232EWE+T - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EWE+T is a 3.0 V to 5.5 V, low-power, true RS-232 transceiver with two drivers and two receivers, supporting data rates up to 1 Mbps in a 16-SOIC package. It provides plus or minus 15 kV ESD protection on the serial-port connection pins and operates from four 0.1 uF charge-pump capacitors. A true RS-232 transceiver converts logic-level signals from a UART, microcontroller, or host into balanced, bipolar serial-port levels, then converts incoming serial signals back into CMOS-compatible logic. Within the interface hierarchy, the MAX3232E is a full-duplex RS-232 transceiver, a line-driver and line-receiver circuit, and a serial interface IC commonly used for legacy serial ports, industrial equipment, and embedded control links. Key features include a 3.0 V minimum supply voltage, a 5.5 V maximum supply voltage, and an operating data rate of up to 1 Mbps. The MAX3232E adds plus or minus 15 kV ESD protection, while its low-power design supports shutdown and reduced-power operating modes for portable or space-constrained equipment. Four external 0.1 uF capacitors allow the on-chip charge pump to generate the positive and negative voltages required by true RS-232 drivers. Internally, the device combines two line drivers, two line receivers, and a dual charge-pump circuit. The charge-pump architecture supports operation from a single 3.0 V to 5.5 V supply instead of a plus or minus voltage source. This simplifies board design, although external capacitor placement and connector-side transient protection remain essential for reliable serial links in industrial environments. Typical applications include RS-232 connections to test and measurement equipment, database controllers, modems, point-of-sale terminals, industrial control panels, and legacy service-port interfaces. The 1 Mbps capability is useful for short, point-to-point links where legacy software expects standard RS-232 signaling, while the 16-SOIC package simplifies assembly on through-hole-compatible boards. When laying out this transceiver, place the four 0.1 uF charge-pump capacitors close to their designated pins and route connector-side signals away from sensitive logic. Keep the interface ground reference close to the connector ground and confirm that the host UART voltage levels match the MAX3232E logic supply. This page organizes the MAX3232EWE+T specifications, package details, drop-in alternatives, application guidance, and design notes into a single engineering reference for RS-232 interface design and sourcing decisions.

Permintaan RFG Kontak
MAX3232EWE-TG068 - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EWE-TG068

MAX3232EWE-TG068 - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EWE-TG068 is a true RS-232 transceiver with two drivers and two receivers, operation from 3.0 V to 5.5 V, and data rates up to 1 Mbps in a 16-pin SOIC package. The MAX3232E family is designed for low-power industrial and embedded serial interfaces using 0.1 µF charge-pump capacitors. A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into logic levels. It belongs to the RS-232 transceiver class, interface IC category, and broader data-conversion and communications-semiconductor hierarchy. Such devices bridge UART, microcontroller, industrial-controller, and data-acquisition equipment across the voltage, noise, and ground-offset differences inherent in RS-232 links. The principal features of the MAX3232E include a 3.0 V to 5.5 V supply range, operation up to 1 Mbps, and integrated charge-pump circuitry that permits the use of four 0.1 µF capacitors. The 2/2 channel arrangement supports two RS-232 transmit channels and two receive channels in one package. Its 16-pin SOIC format supports conventional surface-mount assembly while conserving board area in compact control and communications equipment. The MAX3232E architecture is appropriate for systems in which a logic-level UART must communicate with legacy RS-232 peripherals. On-board level translation permits the host side to operate at low digital logic voltages while the cable side uses RS-232 signaling. Charge-pump-assisted drivers produce the required bipolar voltage swings without requiring a separate negative supply. The receiver side restores compatible logic levels while helping the interface withstand the electrical characteristics of a cable-connected RS-232 port. Typical applications include industrial serial controllers, instrumentation, barcode and identification equipment, point-of-sale terminals, security equipment, and embedded control systems. The 1 Mbps capability is useful for short-distance, higher-speed links where the connected RS-232 equipment supports the same rate. The 3.0 V minimum supply also allows use in modern 3.3 V systems, while the 5.5 V maximum supports conventional 5 V equipment. PCB implementation requires careful treatment of the charge-pump capacitor network and the RS-232 connector. Place the four 0.1 µF capacitors close to their associated device pins, use a continuous ground plane, and follow the manufacturer datasheet layout to minimize switching noise and capacitor-loop inductance. Confirm the connector's signal and ground assignments before PCB release. This product summary combines the manufacturer's family specifications, the exact 16-SOIC package identification, lifecycle information, and application-focused guidance. It also distinguishes the readily identifiable same-package replacement from broader functional equivalents so engineers can evaluate board-level compatibility before committing a design to procurement.

Permintaan RFG Kontak
MAX3232ICAE - 3.0-5.5V 1Mbps RS-232 Transceiver | ADI
MAX3232ICAE

MAX3232ICAE - 3.0-5.5V 1Mbps RS-232 Transceiver | ADI

The Analog Devices MAX3232ICAE is a low-power, true RS-232 transceiver designed for single-supply operation from 3.0 V to 5.5 V, with a maximum data rate of 1 Mbps. The device is packaged in a 16-pin SSOP and is identified by Analog Devices as a production part. It provides the voltage-level conversion required between a modern CMOS or low-voltage TTL serial interface and a ±RS-232 line, allowing legacy ports, industrial equipment, and service interfaces to remain accessible through a compact transceiver. An RS-232 transceiver is an interface IC within the broader hierarchy of communication transceivers, serial-interface controllers, interface ICs, and integrated circuits. Unlike RS-485 and RS-422 links, true RS-232 uses single-ended signaling with bipolar voltage levels and full-duplex point-to-point communication. The MAX3232ICAE therefore fits the driver-and-receiver role between a UART and a DB9, RJ45-style serial connector, or custom RS-232 cabling. The MAX3232 family's headline characteristics are its 3.0 V to 5.5 V supply range, 1 Mbps maximum signaling rate, and low-power operation. The MAX3232E family documented on the same Analog Devices product page adds ±15 kV ESD protection and reduces supply current to as low as 10 nA, while the MAX3232ICAE designation represents the original MAX3232 variant rather than the E-enhanced version. Charge-pump circuitry provides the bipolar transmit voltage required by RS-232 without requiring a separate negative supply. Typical applications include industrial control consoles, programmable-logic-controller service ports, test and measurement equipment, point-of-sale terminals, and embedded systems that retain a legacy serial interface. The 16-pin SSOP keeps the design compact, while the 3.0 V minimum supply allows operation from 3.3 V systems without a 5 V-only supply requirement. Designers should still allow correct charge-pump capacitor selection and external protection for the cable-connected pins. When laying out the board, place the charge-pump capacitors and the VCC bypass capacitor close to their associated pins, and route driver outputs away from sensitive receiver inputs. Keep RS-232 traces short where possible and provide chassis-ground or surge-protection measures according to the cable environment. Interface protection is distinct from the internal ESD characteristics of the MAX3232E version, so the selected ordering code must match the protection requirement for the end product. This page brings together the manufacturer specifications, package details, verified drop-in alternatives, application guidance, and layout considerations in one engineering reference. It also distinguishes the original MAX3232ICAE from the ESD-enhanced MAX3232E and documents which replacement parts preserve the same 16-pin SSOP footprint.

Permintaan RFG Kontak
MAX3232ICSE - 3.0V 1Mbps RS-232 Transceiver | Maxim
MAX3232ICSE

MAX3232ICSE - 3.0V 1Mbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3232ICSE is a 3.0V-to-5.5V, low-power true RS-232 line driver and receiver capable of operation at data rates up to 1Mbps. The device provides one transmitter and one receiver in a 16-SOIC package, making it suitable for UART-to-RS-232 conversion, industrial serial links, data acquisition equipment, and embedded control systems. The MAX3232 family uses a dual charge-pump architecture to generate the positive and negative voltages required by RS-232 drivers from a single low-voltage supply. A true RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into compliant bipolar RS-232 levels and converts received RS-232 signals back into CMOS-compatible logic levels. Within the electronics hierarchy, it belongs to the RS-232 transceiver class, then the line-driver and receiver class, and ultimately the interface IC and power-management ecosystem. This hierarchy matters because the interface must bridge modern 3.3V or 5V digital systems with the voltage and signaling conventions of legacy serial equipment. According to the manufacturer's product information, the MAX3232 operates from 3.0V to 5.5V, supports data rates up to 1Mbps, and includes low-power operation. Its true RS-232 implementation reduces the need for external level-shifting components when connecting a microcontroller UART to a DB-9 or DB-25 connector. The low-voltage supply range also enables direct use in 3.3V embedded systems without a separate 5V transceiver. The dual charge pump generates the bipolar voltage rails required by the transmitter. Four external charge-pump capacitors support this operation, while the receiver translates the bipolar RS-232 input to a single-supply logic output. Designers must account for capacitor tolerances, charge-pump ripple, and the increased supply current that can occur when a connected RS-232 driver is active. The internal design simplifies the interface compared with discrete transistor drivers but does not eliminate good PCB-layout and decoupling practices. Typical uses include USB-to-RS-232 adapters, test and measurement instruments, industrial controllers, security equipment, and service-port links. The 1Mbps capability gives designers margin for higher-speed UART traffic while retaining compatibility with common communication standards used in legacy RS-232 equipment. The exact ordering-code details, including temperature grade and package suffix interpretation, should be confirmed against the manufacturer part-selection information before production release. For a reliable layout, place the charge-pump capacitors and supply bypass capacitor close to their associated pins, route the driver and receiver nets away from sensitive analog circuitry, and provide a controlled ground return for the cable interface. Keep the RS-232 connector-side nets isolated from low-level digital signals to reduce coupled noise and improve ESD survivability. This page combines the MAX3232 family specifications, verified package information, interface-level design guidance, and focused replacement comparisons. These engineering details help distinguish electrically similar transceivers by voltage range, data rate, temperature grade, package, and protection performance before a component is selected for a new or existing RS-232 design.

Permintaan RFG Kontak
MAX3232ID - 2/2 RS-232 Transceiver, 5.5V, SOIC-16 | TI
MAX3232ID

MAX3232ID - 2/2 RS-232 Transceiver, 5.5V, SOIC-16 | TI

The Texas Instruments MAX3232ID is a 2/2 RS-232 line driver and receiver operating from a 3 V to 5.5 V supply in a 16-pin SOIC package. It supports data rates up to 250 kbit/s, accepts 5 V logic, and provides ±15 kV ESD protection on the RS-232 terminals. The device uses a dual charge-pump architecture and four external 0.1 µF capacitors to generate the bipolar voltage required for RS-232 signaling. An RS-232 transceiver is an interface IC that converts between low-voltage CMOS logic levels and the positive and negative voltage levels used by RS-232 ports. Within the broader semiconductor hierarchy, it is a line transceiver, then an interface IC, and finally a power-management and connectivity component. It is intended for asynchronous point-to-point serial communication, particularly where legacy computers, industrial equipment, test systems, or peripherals use DB-style RS-232 connectors. The principal features of the MAX3232ID are its dual-driver, dual-receiver configuration, 3 V to 5.5 V operation, 250 kbit/s maximum data rate, and ±15 kV terminal-to-terminal ESD protection. According to the manufacturer datasheet, it meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. Its typical supply current is 300 µA, making it suitable for low-power serial interfaces where the host operates intermittently. The MAX3232ID uses a charge-pump voltage converter with external capacitors to develop the negative voltage required by an RS-232 driver. The logic-side pins remain compatible with 5 V CMOS systems, while the driver outputs deliver RS-232-compatible levels. The four required 0.1 µF capacitors should be placed close to their associated supply and ground pins to minimize switching noise and maintain stable charge-pump operation. Typical applications include industrial serial-port adapters, laboratory instrumentation, POS terminals, configuration ports, legacy peripheral upgrades, and embedded systems that retain an RS-232 physical interface. It is particularly appropriate where a 3.3 V or 5 V controller must communicate with an RS-232 device without adding a separate external negative-voltage supply. The primary design consideration is capacitance selection and PCB placement. Use the specified 0.1 µF capacitors, keep charge-pump loops compact, connect the device ground to the interface reference ground, and route the RS-232 traces away from sensitive analog or high-speed digital signals. External protection may still be needed for long or exposed cables even though the integrated terminals provide ±15 kV ESD protection. This product data combines verified manufacturer and distributor information with application guidance, package details, pricing context, and drop-in replacement analysis. It focuses on engineering decisions that are not apparent from a distributor title alone: data-rate capability, supply range, ESD coverage, charge-pump implementation, replacement compatibility, and layout constraints.

Permintaan RFG Kontak
MAX3232IDB - Dual 250kbps RS-232 Transceiver | Texas Instruments
MAX3232IDB

MAX3232IDB - Dual 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IDB is a dual RS-232 line driver and receiver with a 3 V to 5.5 V supply, operation to 250 kbit/s, and ±15 kV ESD protection, supplied in a 16-pin SSOP package. The device combines two drivers, two receivers, and a dual charge-pump circuit on one IC. An RS-232 transceiver is the interface circuit between low-voltage digital logic and the higher-voltage, bipolar signaling used by RS-232 equipment. The MAX3232 translates digital transmitter inputs into RS-232-level driver outputs and converts incoming RS-232 receiver signals into logic-compatible levels. Within the interface IC hierarchy, it belongs to the RS-232 transceiver class of communication interface semiconductors. Key features include a 3 V to 5.5 V operating supply, two drivers, two receivers, 250 kbit/s operation, and 5 V logic compatibility. The on-chip charge pump generates the positive and negative voltages required by the RS-232 drivers. The manufacturer describes the device as meeting or exceeding TIA/EIA-232-F and ITU V.28 requirements. It also accepts 5 V logic inputs, allowing the device to bridge 3.3 V or 5 V systems to RS-232 ports. The dual charge-pump design supports low-power RS-232 communication without a separate negative supply. Charge-pump capacitors connected to C1+, C1−, C2+, and C2− develop the bipolar voltage rails needed to drive the outputs. Because the MAX3232IDB supports both 3 V and 5 V supply operation, it can be used in mixed-voltage embedded systems where the logic source operates from 3.3 V while the RS-232 port requires compliant bipolar signal levels. Typical applications include industrial serial consoles, data acquisition systems, instrumentation, barcode and identification equipment, point-of-sale terminals, and embedded systems using asynchronous RS-232 links. Its 250 kbit/s capability is suitable for moderate-speed control and diagnostic traffic rather than high-bandwidth video or storage transfers. Industrial designs benefit from the ±15 kV ESD protection specified for the serial-port connection pins. When laying out the circuit, place the four external 0.1 µF charge-pump capacitors close to their associated pins and maintain a short return path through the device ground. Confirm that the external capacitors meet the voltage and tolerance requirements in the manufacturer datasheet. RS-232 cable transients still require appropriate system-level grounding and protection; on-chip ESD protection does not replace correctly designed cable and enclosure engineering. This page combines the exact electrical ratings, package information, pricing structure, drop-in replacement relationships, and application guidance needed to evaluate the MAX3232IDB in a new RS-232 design. It also highlights where a MAX3232E-family device may be preferable and where strict production equivalence should be confirmed before substitution.

Permintaan RFG Kontak
MAX3232IDBG4 - Dual 250kbps RS-232 Transceiver | Texas Instruments
MAX3232IDBG4

MAX3232IDBG4 - Dual 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IDBG4 is a dual-channel RS-232 line driver and receiver operating from 3 V to 5.5 V at a maximum data rate of 250 kbps, supplied in a 16-pin SSOP package. The device combines two line drivers, two line receivers, and a dual charge-pump circuit, while its serial-port pins provide ±15 kV ESD protection. It is designed for bidirectional RS-232 interfaces in industrial, embedded, and data-communication equipment. An RS-232 transceiver is the interface circuit that converts logic-level signals into RS-232 voltage levels and restores incoming RS-232 signals to logic-compatible levels. The MAX3232 belongs to the interface IC and RS-232 transceiver hierarchy, where the charge-pump circuitry supports single-supply operation without a separate negative power rail. The two-driver, two-receiver arrangement provides two complete point-to-point serial channels in one package. Key features include a 3 V to 5.5 V operating range, 250 kbps data-rate capability, two drivers, two receivers, and ±15 kV ESD protection on the serial-port connections. According to the Texas Instruments MAX3232 datasheet, the device meets the requirements of TIA/EIA-232-F. Its industrial temperature option operates from −40°C to +85°C, making the part suitable for equipment operating across extended commercial and industrial temperature ranges. The internal dual charge-pump circuit generates the positive and negative voltage levels required by RS-232 while operating from one low-voltage supply. Charge-pump capacitors are required to implement this function, while the external interface also needs the application-specific charge-pump capacitor arrangement and input/output bypass capacitors described in the manufacturer datasheet. The charge pumps do not eliminate the need for correct bypass-capacitor selection; their switching activity must remain compatible with the signal quality required by the connected equipment. Typical uses include RS-232 adapters, industrial control panels, test equipment, barcode scanners, data loggers, embedded service interfaces, and legacy peripheral connections. A particularly suitable use is a two-channel industrial controller that requires two RS-232 ports while operating from a 3.3 V or 5 V system supply. For long cables or externally accessible connectors, the ±15 kV ESD rating adds protection, although board-level grounding and surge design must still address the complete enclosure and cable environment. Designers should preserve the manufacturer-specified charge-pump and bypass-capacitor values, place them close to their associated pins, and route RS-232 driver outputs and receiver inputs away from sensitive low-level circuitry. Do not substitute a functionally similar transceiver without checking its package pinout, supply range, driver and receiver count, data rate, and ESD implementation. These checks are essential because a shared package name alone does not guarantee electrical or timing compatibility. This product guide combines the manufacturer specification with application-oriented integration guidance, drop-in alternatives, and a parameter comparison that supports faster design reviews. It also emphasizes practical distinctions involving the improved MAX3232E family, package compatibility, operating temperature, channel count, and interface protection so engineers can select a replacement without overlooking board-level constraints.

Permintaan RFG Kontak
MAX3232IDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232IDBR

MAX3232IDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232IDBR is a dual-channel RS-232 line driver and receiver rated for 250 kbps operation, 3 V to 5.5 V supply voltage, and ±15 kV ESD protection. The device is packaged in a 16-pin SSOP (DB) package and operates from -40°C to +85°C. An RS-232 transceiver is an interface IC that converts digital logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. The MAX3232 belongs to the line-driver/receiver hierarchy within interface ICs, providing the physical communication layer between a host, microcontroller, or industrial controller and an RS-232 peripheral. The dual architecture provides two drivers and two receivers in one device, reducing the number of external interface components required for bidirectional serial links. Its 250 kbps maximum data rate supports conventional RS-232 equipment, while the 3 V to 5.5 V operating range accommodates both 3.3 V and 5 V systems. The ±15 kV ESD rating strengthens protection against electrostatic discharge at exposed serial ports. The MAX3232IDBR uses an on-chip charge-pump circuit to generate the positive and negative voltage levels required by RS-232. Charge-pump capacitors and the supply bypass capacitor must be connected according to the manufacturer datasheet. Because these switching elements can produce ripple on the power rail, power and return connections should be arranged to prevent coupling into sensitive analog or timing circuitry. Typical uses include industrial serial controllers, point-of-sale terminals, data-acquisition equipment, instrumentation, and service interfaces for microcontrollers. The device is particularly appropriate when two RS-232 channels must fit into a compact PCB area and the system operates from a 3.3 V or 5 V supply. When laying out the circuit, place charge-pump and bypass capacitors close to their designated pins and keep the RS-232 driver outputs away from sensitive receiver inputs. Provide adequate ground and power-return paths to reduce ground bounce when the drivers switch between positive and negative RS-232 levels. This product overview combines electrical characteristics, lifecycle information, drop-in replacement choices, comparison data, and practical layout guidance to support faster RS-232 interface design and sourcing.

Permintaan RFG Kontak
MAX3232IDE4 - 250kbps 2/2 RS-232 Transceiver | Texas Instruments
MAX3232IDE4

MAX3232IDE4 - 250kbps 2/2 RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IDE4 is a 2/2 RS-232 line-driver and receiver transceiver with a 3 V to 5.5 V supply range, operation up to 250 kbit/s, and a 16-pin SOIC package. The device also provides ±15 kV human-body-model ESD protection on the serial-port connection pins and operates in the -40°C to +85°C industrial temperature range. An RS-232 transceiver is an interface IC that bridges the logic-level voltage domain of a controller or computer with the higher-voltage, bipolar signaling domain used by RS-232 equipment. The MAX3232 category combines two drivers, two receivers, and dual charge-pump circuitry that generates the positive and negative voltages required by compliant RS-232 line drivers. The principal features are two transmit channels, two receive channels, full-duplex operation, and data rates up to 250 kbit/s. Its dual charge-pump design permits operation from a single 3 V to 5.5 V supply without an external negative supply. The integrated charge-pump capacitors support a compact implementation in the 16-SOIC surface-mount package. The MAX3232 architecture translates TTL and CMOS-compatible input signals to RS-232 levels and converts incoming RS-232 signals back to logic levels. Its 300 ns propagation delay supports dependable communication across conventional serial links. The protected line-driver and line-receiver pins are intended for exposed serial connectors where electrostatic discharge is a practical concern. Typical uses include industrial serial-port equipment, data-acquisition systems, embedded-control consoles, point-of-sale terminals, and legacy peripheral interfaces. The dual-channel arrangement is particularly useful when a product needs one transmit and one receive path for RS-232 communication while preserving a second driver or receiver for status, control, or another RS-232 port. PCB design should place the charge-pump capacitors close to their associated pins and provide a direct ground return to the device. Keep the RS-232 traces short and route them away from sensitive clock, reset, and analog signals. External protection may still be required when long cables or severe industrial transients are expected. This product record combines electrical specifications, package details, application guidance, drop-in alternatives, and practical layout considerations to support component selection and PCB implementation. The comparison tables also highlight temperature-grade, package, and feature differences that should be reviewed before approving a substitute.

Permintaan RFG Kontak
MAX3232IDG4 - 2/2 RS-232 Transceiver, 3-5.5V, 16-SOIC | TI
MAX3232IDG4

MAX3232IDG4 - 2/2 RS-232 Transceiver, 3-5.5V, 16-SOIC | TI

The Texas Instruments MAX3232IDG4 is a 2/2 full RS-232 transceiver with a 3 V to 5.5 V supply range, designed for bidirectional serial-interface conversion and packaged in a 16-pin SOIC. It integrates two line drivers, two line receivers, a dual charge-pump circuit, and ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or peripheral and a differential, bipolar RS-232 link. Within the signal-chain hierarchy, it belongs to the RS-232 transceiver class, interface IC category, and broader semiconductor ecosystem. The MAX3232IDG4 supports both transmit and receive functions while operating from a single 3 V to 5.5 V supply, making it suitable for systems whose digital logic and serial interface use different supply domains. The device provides two driver channels and two receiver channels, allowing two RS-232 ports to be implemented within one package. Its stated data rate reaches 1 Mbps, and its charge-pump-based level translation uses four external 0.1 µF capacitors. These features suit legacy serial connectivity, industrial control links, service equipment, and embedded systems that still expose an RS-232 port but retain a CMOS or TTL-level host interface. Internally, the MAX3232IDG4 combines the two line drivers, two line receivers, and dual charge-pump circuitry in one package. Charge-pump circuitry develops the positive and negative voltages required by the RS-232 signaling specification, while the integrated line interface handles thresholding and signal translation. The manufacturer describes the device as meeting the requirements of TIA/EIA-232-F and provides ±15 kV ESD protection on all serial-port pins, including ground. Typical uses include configuration and maintenance ports on industrial equipment, point-to-point links between embedded controllers and legacy peripherals, and service interfaces for test or measurement instruments. The 16-SOIC package supports conventional surface-mount assembly while preserving a small enough footprint for compact control boards. Designers should still account for the four charge-pump capacitors in placement and stability planning. A key implementation detail is that the external 0.1 µF capacitors must be connected according to the manufacturer application schematic. Keep these charge-pump components close to their designated pins, provide uninterrupted ground return paths for both logic and serial interfaces, and route exposed cable-side traces away from sensitive clock and analog nodes. Verify signal polarity and connector-side protection before field deployment. This page combines the manufacturer-described electrical characteristics, package information, verified sourcing links, and interface-specific engineering guidance to support component selection, PCB implementation, and drop-in replacement assessment.

Permintaan RFG Kontak
MAX3232IDRE4 - 3V RS-232 Transceiver | Texas Instruments
MAX3232IDRE4

MAX3232IDRE4 - 3V RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232IDRE4 is a 2/2 full-duplex RS-232 line-driver and receiver transceiver with a 3 V to 5.5 V supply range, data rates up to 250 kbit/s, and ±15 kV human-body-model ESD protection, packaged in a 16-pin SOIC. Its integrated charge-pump circuitry supports low-power RS-232 communication from 3 V or 5 V systems without requiring a separate negative supply. An RS-232 transceiver is an interface IC that converts logic-level TTL or CMOS signals into balanced, bipolar RS-232 line levels and converts received line signals back into logic levels. The MAX3232IDRE4 belongs to the RS-232 interface transceiver hierarchy within integrated circuits and provides the physical-layer conversion required between a digital controller and a serial data port. The device includes two line drivers and two line receivers, supporting two RS-232 channels in full-duplex operation. Its 3 V to 5.5 V operating range makes it suitable for systems using either 3.3 V or 5 V logic. The 250 kbit/s maximum data rate supports higher-speed point-to-point links, while ±15 kV HBM ESD protection improves robustness when cables connect the board to external equipment. The MAX3232IDRE4 uses the Maxim RS-232 approach in which on-chip charge pumps generate the positive and negative voltages required by RS-232 transmitters. Four external 0.1 µF capacitors support the charge-pump and transmit functions. This arrangement eliminates the need for a separate negative supply rail while retaining compatibility with established RS-232 interface practice. Typical uses include industrial serial consoles, point-to-point configuration links, embedded equipment interfaces, and peripheral connectivity. The device can also support full-duplex communication when one driver and one receiver are assigned to each direction. A 16-pin SOIC package supports compact surface-mount PCB construction and automated assembly. Designers should place the required 0.1 µF capacitors close to their associated pins and observe the polarity and voltage limits given in the manufacturer datasheet. External protection may still be needed for exposed cables or severe electrostatic environments. The maximum cable length and data rate should be selected together because both influence signal integrity and communication reliability. This product page brings together the principal electrical ratings, package information, drop-in replacement analysis, comparison data, and practical PCB guidance for engineers evaluating the MAX3232IDRE4 in a compact RS-232 interface design.

Permintaan RFG Kontak
MAX3232IDRG4 - 3.3V RS-232 Transceiver | Texas Instruments
MAX3232IDRG4

MAX3232IDRG4 - 3.3V RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IDRG4 is a 3 V to 5.5 V RS-232 line driver and receiver IC with two transmit channels, two receive channels, operation up to 1 Mbps, and ±15 kV ESD protection, housed in a 16-pin SOIC package. It converts logic-level signals between a host or controller and RS-232-compatible equipment while operating from either 3.3 V or 5 V logic systems. An RS-232 transceiver is an interface IC that combines differential voltage-based line drivers with receiver circuits capable of detecting RS-232 signal levels. The MAX3232 belongs to the broader interface-IC hierarchy, where transceivers connect digital logic to a physical communication standard. Its dual-driver, dual-receiver arrangement supports one RS-232 port while providing a useful balance between board area, power consumption, and peripheral count. The principal benefits include a 3 V to 5.5 V supply range, 1 Mbps maximum data rate, and ±15 kV ESD protection. Operation from 3.3 V allows the device to interface directly with modern low-voltage controller logic without a separate 5 V logic supply. Its two receivers may also be monitored independently when the full RS-232 port is not required. Internally, the MAX3232 uses charge-pump circuitry and external capacitors to generate the bipolar voltage needed by RS-232 line drivers. Four external charge-pump capacitors are required by the standard application arrangement. The integrated protection and voltage-generation functions reduce the number of discrete components needed for a compact RS-232 interface. Typical uses include industrial serial consoles, programmable instrumentation, data acquisition equipment, point-of-sale terminals, and embedded systems that retain an RS-232 port. The device is especially useful when the host operates from 3.3 V while the connected peripheral still uses conventional RS-232 signaling. Place the required charge-pump capacitors close to their associated pins and route each driver output directly toward its connector. Keep the logic-side traces short, provide a solid ground reference, and use the receiver and driver pins according to the Texas Instruments datasheet rather than inferring connections from the generic RS-232 standard. This product page combines the exact package and electrical characteristics, sourcing guidance, functional comparisons, and practical interface-design notes needed to evaluate MAX3232IDRG4 for a new RS-232 design.

Permintaan RFG Kontak
MAX3232IDW - Dual RS-232 Transceiver, 3-5.5V | Texas Instruments
MAX3232IDW

MAX3232IDW - Dual RS-232 Transceiver, 3-5.5V | Texas Instruments

The Texas Instruments MAX3232IDW is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply in a 16-pin SOIC package. It provides two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection on all serial inputs and outputs. An RS-232 transceiver is an interface IC that converts low-voltage CMOS logic signals into RS-232-compatible levels and receives differential bipolar signals back into CMOS logic. Within the interface IC hierarchy, the MAX3232IDW belongs to the RS-232 transceiver family, supports TIA/EIA-232-F and ITU V.28 requirements, and is commonly used to connect 3.3 V or 5 V controllers to legacy serial equipment. Key features include operation from 3 V to 5.5 V, data rates up to 250 kbit/s, low supply current of 300 µA typical, and compatibility with 5 V logic. The charge-pump design generates the positive and negative voltages required for true RS-232 signaling without an external 12 V supply. Four external 0.1 µF capacitors are required for the charge-pump and voltage-regulation functions. The device combines two transmit channels with two receive channels in one package. Each driver converts a CMOS logic input into an RS-232 output, while each receiver converts an RS-232 input into a CMOS output. The internal charge pumps support both 3 V and 5 V operation, allowing the same interface design to be used across common embedded and industrial supply levels. Typical applications include serial port adapters, industrial control equipment, data acquisition systems, point-of-sale terminals, test and measurement instruments, and embedded systems communicating with legacy RS-232 peripherals. The ±15 kV ESD protection improves robustness when cables are connected or disconnected in industrial environments. For PCB layout, place the four 0.1 µF charge-pump capacitors close to their associated pins and route each RS-232 trace away from sensitive analog or high-speed digital signals. Confirm logic thresholds, connector protection, cable length, and grounding before releasing a design, especially when connecting the interface to exposed external cables. This page organizes the electrical limits, package information, verified pricing, drop-in alternatives, and application guidance for engineers evaluating the MAX3232IDW in a new or existing RS-232 design.

Permintaan RFG Kontak
MAX3232IDWR - Dual RS-232 Transceiver, 3-5.5V | Texas Instruments (Tape & Reel)
MAX3232IDWR

MAX3232IDWR - Dual RS-232 Transceiver, 3-5.5V | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232IDWR is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply in a 16-pin SOIC package. It provides two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection on all serial inputs and outputs. An RS-232 transceiver is an interface IC that converts low-voltage CMOS logic signals into RS-232-compatible levels and receives differential bipolar signals back into CMOS logic. Within the interface IC hierarchy, the MAX3232IDWR belongs to the RS-232 transceiver family, supports TIA/EIA-232-F and ITU V.28 requirements, and is commonly used to connect 3.3 V or 5 V controllers to legacy serial equipment. Key features include operation from 3 V to 5.5 V, data rates up to 250 kbit/s, low supply current of 300 µA typical, and compatibility with 5 V logic. The charge-pump design generates the positive and negative voltages required for true RS-232 signaling without an external 12 V supply. Four external 0.1 µF capacitors are required for the charge-pump and voltage-regulation functions. The device combines two transmit channels with two receive channels in one package. Each driver converts a CMOS logic input into an RS-232 output, while each receiver converts an RS-232 input into a CMOS output. The internal charge pumps support both 3 V and 5 V operation, allowing the same interface design to be used across common embedded and industrial supply levels. Typical applications include serial port adapters, industrial control equipment, data acquisition systems, point-of-sale terminals, test and measurement instruments, and embedded systems communicating with legacy RS-232 peripherals. The ±15 kV ESD protection improves robustness when cables are connected or disconnected in industrial environments. For PCB layout, place the four 0.1 µF charge-pump capacitors close to their associated pins and route each RS-232 trace away from sensitive analog or high-speed digital signals. Confirm logic thresholds, connector protection, cable length, and grounding before releasing a design, especially when connecting the interface to exposed external cables. This page organizes the electrical limits, package information, verified pricing, drop-in alternatives, and application guidance for engineers evaluating the MAX3232IDWR in a new or existing RS-232 design.

Permintaan RFG Kontak
MAX3232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments
MAX3232IDWRG4

MAX3232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IDWRG4 is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply, with a maximum data rate of 250 kbps and ±15 kV ESD protection on each I/O pin. The device is packaged in a 16-pin SOIC (DW) package and is specified for an industrial temperature range of -40°C to +85°C. An RS-232 transceiver is an interface IC that converts low-voltage logic signals into RS-232 line levels and receives differential bipolar signals, converting them back into CMOS-compatible logic levels. This dual-driver, dual-receiver arrangement places the MAX3232IDWRG4 within the hierarchy of interface ICs, serial transceivers, line drivers and receivers, and data-conversion semiconductors. It is used where a powered system must exchange data with an RS-232 equipment port. The principal features include two transmit channels, two receive channels, operation from a single 3 V to 5.5 V supply, data rates up to 250 kbps, and ±15 kV ESD protection. The industrial-temperature rating supports equipment operating across extended ambient conditions. These characteristics make the device suitable for industrial controls, test equipment, POS terminals, and embedded systems that communicate with legacy RS-232 peripherals. The MAX3232 interface architecture uses on-chip level-shifting circuitry to produce the positive and negative voltage swings required by RS-232 while operating from a modern low-voltage supply. Because RS-232 is a point-to-point interface, each transmitter should drive one receiver and the connection should include signal-ground continuity. The 250 kbps capability supports legacy control and diagnostic protocols without requiring a separate line-driver IC. Typical applications include industrial serial controllers, laboratory test systems, point-of-sale equipment, barcode scanners, and service-console interfaces. In each case, the IC handles the physical RS-232 voltage conversion while the host UART handles framing, parity, and data-rate configuration. The device can therefore simplify board partitioning by combining the driver and receiver functions in one package. PCB implementation should preserve the required charge-pump capacitors, route each RS-232 line away from sensitive analog signals, and provide a low-impedance ground path between the two connected systems. Confirm the external capacitor values, pin assignments, and maximum driver-load requirements against the manufacturer datasheet before releasing a new layout. The device is a digital interface IC, so a safe operating area curve is not applicable. This product record combines the manufacturer’s electrical and package specifications, sourcing guidance, practical layout considerations, and same-footprint replacement information. It is intended to help engineers evaluate the MAX3232IDWRG4 for new designs, cross-reference legacy RS-232 interfaces, and plan industrial-temperature production boards.

Permintaan RFG Kontak
MAX3232IPW - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232IPW

MAX3232IPW - 250kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IPW is a dual-channel RS-232 line driver and receiver operating from 3V to 5.5V, supporting data rates up to 250kbit/s and providing ±15kV ESD protection. The device is packaged in a 16-pin TSSOP package. It combines two RS-232 drivers, two RS-232 receivers, and onboard charge-pump circuitry that produces the bipolar voltage levels required by the RS-232 interface. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and a serial communications link using single-ended, bipolar signaling. The MAX3232 belongs to the RS-232 interface transceiver hierarchy, where line drivers convert logic signals into RS-232 levels and receivers convert transmitted levels back into CMOS-compatible logic. Its onboard charge pumps allow operation from a single 3V to 5.5V supply rather than requiring a separate ±12V supply. The MAX3232 provides two transmit channels and two receive channels, making it appropriate for implementing a compact RS-232 port. Its maximum 250kbit/s data rate supports conventional serial-port communication while exceeding the throughput needed by many control, instrumentation, and industrial interfaces. The integrated protection is specified to ±15kV on the serial-port connection terminals, including ground, improving robustness when cables are exposed to electrostatic discharge. Internally, the charge-pump circuits generate the positive and negative voltages required by the drivers, while the receiver section provides RS-232 thresholding and noise-tolerant logic-level output. According to the manufacturer datasheet, the device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. It also accepts 5V logic, allowing the interface to operate alongside conventional 5V digital systems. Typical applications include industrial control links, test and measurement equipment, POS terminals, security systems, and embedded serial-port designs. The dual-channel arrangement can support one full-duplex RS-232 connection or two unidirectional links, depending on how the driver and receiver pins are assigned. The 16-pin TSSOP package also supports compact surface-mount PCB layouts. When laying out the circuit, place the required external charge-pump capacitors close to their designated pins and route the RS-232 connector-side traces away from sensitive logic. Confirm that the selected external capacitors meet the device's voltage and tolerance requirements. Also verify the electrical requirements of the connected equipment before substituting a similarly packaged transceiver. This page consolidates the verified manufacturer and distributor information with practical interface-layout guidance, pin-compatible alternatives, and a parameter comparison. It is intended to accelerate component selection while keeping all unverified electrical details explicitly identified rather than inferred.

Permintaan RFG Kontak
MAX3232IPWG4 - RS-232 Transceiver | Texas Instruments
MAX3232IPWG4

MAX3232IPWG4 - RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IPWG4 is a multichannel RS-232 line driver and receiver IC with 3 V to 5.5 V single-supply operation, integrated charge-pump voltage conversion, and ±15 kV ESD protection. The device provides two transmit channels and two receive channels in a 16-pin TSSOP package, making it suitable for industrial serial interfaces, data acquisition equipment, and embedded control systems. Its receiver includes enhanced ESD protection and fail-safe operation, while the transmitters support RS-232 signal levels from a low-voltage digital supply. An RS-232 transceiver combines a line driver, line receiver, and level-shifting charge-pump circuit in one package. The driver converts low-voltage logic signals into RS-232-compatible levels, while the receiver converts bipolar RS-232 signals back into CMOS-compatible logic. This integration reduces external circuitry, simplifies system design, and is especially useful when the host interface operates at 3.3 V or 5 V but the connected equipment requires RS-232 voltage levels. The MAX3232IPWG4 operates across a 3 V to 5.5 V supply range, allowing use with both 3.3 V and 5 V systems. Its multichannel architecture supports two RS-232 transmit and two receive functions in one 16-terminal TSSOP package. The integrated charge pump generates the positive and negative voltage levels required by RS-232 without a separate negative supply, and the integrated protection circuitry helps improve robustness when ports are exposed to electrostatic discharge. The part is specified for an industrial operating temperature range of -40 °C to +85 °C and uses a 0.65 mm terminal pitch. Its 16-pin TSSOP construction supports compact PCB layouts while preserving enough pin density for two full-duplex RS-232 channels. The MAX3232IPWG4 is also associated with a ±15 kV ESD-protection feature in the device family documentation, making it a practical choice for equipment interfaces exposed to cable transients. Typical applications include serial adapters, industrial controllers, test equipment, point-of-sale terminals, embedded instrumentation, and communication links between a low-voltage processor and an RS-232 peripheral. Designers should provide the external charge-pump capacitors and, where required, the recommended driver and receiver bypass capacitors at the pins specified by the manufacturer datasheet. Keep the RS-232 traces short, route them away from sensitive clock and analog signals, and connect the protection ground arrangement as recommended for the application. The MAX3232 family also includes an improved MAX3232E replacement recommended by Texas Instruments for new designs. Engineers evaluating alternatives should compare supply range, channel count, ESD rating, logic levels, package, and capacitor requirements before approving a substitution. This page combines device specifications, replacement guidance, package information, and practical interface-design considerations for faster engineering selection.

Permintaan RFG Kontak
MAX3232IPWR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232IPWR

MAX3232IPWR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX3232IPWR is a dual-channel RS-232 line driver and receiver operating from 3V to 5.5V, supporting data rates up to 250kbit/s and providing ±15kV ESD protection. The device is packaged in a 16-pin TSSOP package. It combines two RS-232 drivers, two RS-232 receivers, and onboard charge-pump circuitry that produces the bipolar voltage levels required by the RS-232 interface. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and a serial communications link using single-ended, bipolar signaling. The MAX3232 belongs to the RS-232 interface transceiver hierarchy, where line drivers convert logic signals into RS-232 levels and receivers convert transmitted levels back into CMOS-compatible logic. Its onboard charge pumps allow operation from a single 3V to 5.5V supply rather than requiring a separate ±12V supply. The MAX3232 provides two transmit channels and two receive channels, making it appropriate for implementing a compact RS-232 port. Its maximum 250kbit/s data rate supports conventional serial-port communication while exceeding the throughput needed by many control, instrumentation, and industrial interfaces. The integrated protection is specified to ±15kV on the serial-port connection terminals, including ground, improving robustness when cables are exposed to electrostatic discharge. Internally, the charge-pump circuits generate the positive and negative voltages required by the drivers, while the receiver section provides RS-232 thresholding and noise-tolerant logic-level output. According to the manufacturer datasheet, the device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. It also accepts 5V logic, allowing the interface to operate alongside conventional 5V digital systems. Typical applications include industrial control links, test and measurement equipment, POS terminals, security systems, and embedded serial-port designs. The dual-channel arrangement can support one full-duplex RS-232 connection or two unidirectional links, depending on how the driver and receiver pins are assigned. The 16-pin TSSOP package also supports compact surface-mount PCB layouts. When laying out the circuit, place the required external charge-pump capacitors close to their designated pins and route the RS-232 connector-side traces away from sensitive logic. Confirm that the selected external capacitors meet the device's voltage and tolerance requirements. Also verify the electrical requirements of the connected equipment before substituting a similarly packaged transceiver. This page consolidates the verified manufacturer and distributor information with practical interface-layout guidance, pin-compatible alternatives, and a parameter comparison. It is intended to accelerate component selection while keeping all unverified electrical details explicitly identified rather than inferred.

Permintaan RFG Kontak
MAX3232IPWRE4 - Dual RS-232 Transceiver | Texas Instruments
MAX3232IPWRE4

MAX3232IPWRE4 - Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IPWRE4 is a dual-channel RS-232 line-driver and line-receiver transceiver operating from a 3 V to 5.5 V supply, supporting data rates up to 250 kbit/s in a 16-pin TSSOP package. The device integrates two drivers, two receivers, a dual charge-pump circuit, and pin-to-pin ±15 kV ESD protection on the serial-port connection pins. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and the voltage levels used by RS-232 serial equipment. The MAX3232 combines bipolar line-driver outputs, receiver inputs, and charge-pump-assisted level shifting in one package. This integration allows a modern microcontroller or processor with TTL or CMOS-compatible logic to communicate with legacy RS-232 peripherals over a multi-drop or point-to-point serial link. Principal features include two transmit channels, two receive channels, operation from a 3 V to 5.5 V VCC supply, and a maximum data rate of 250 kbit/s. The MAX3232 accepts 5 V logic, requires external 0.1 µF charge-pump capacitors, and has a typical low supply current of 300 µA. The industrial-temperature ordering option supports operation from −40 °C to 85 °C while maintaining a surface-mount footprint suitable for compact embedded equipment. The integrated dual charge pump generates the positive and negative voltage levels needed by RS-232 transmitters. Although the interface-side supply is only 3 V to 5.5 V, the driver outputs use the charge-pump voltage rails to provide RS-232-compatible signaling. The receiver section converts the bipolar RS-232 input levels into logic-compatible signals, allowing the same device to support complete host-to-peripheral serial links when both driver and receiver channels are used. Typical applications include industrial serial-port controllers, point-of-sale terminals, test and measurement equipment, data-acquisition systems, and embedded control boards that require an RS-232 connection. The 250 kbit/s capability is suitable for legacy serial protocols, while the integrated ±15 kV ESD protection helps improve robustness when cables connect the board to external equipment. The charge-pump capacitors must be placed close to their associated pins, and the logic and serial interfaces should be routed to reduce noise coupling. Check the device’s supply, logic-level, temperature, and ESD requirements before production release, especially when replacing an RS-232 component with different channel counts or a different package. This product page consolidates the MAX3232IPWRE4 interface specifications, package information, practical RS-232 design guidance, and verified replacement considerations. It is intended to help engineers evaluate the part quickly while preserving the distinction between electrical compatibility, package compatibility, and application-specific design requirements.

Permintaan RFG Kontak
MAX3232IPWRG4 - 3-5.5V RS-232 Transceiver | Texas Instruments
MAX3232IPWRG4

MAX3232IPWRG4 - 3-5.5V RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232IPWRG4 is a 3 V to 5.5 V dual RS-232 line driver and receiver with a 16-pin TSSOP package, two transmit channels, two receive channels, and ±15-kV ESD protection on the serial-port terminals. It is designed to connect an asynchronous communication controller to an RS-232 connector while operating from a single low-voltage supply. An RS-232 transceiver is a semiconductor interface that converts logic-level signals into RS-232 line levels and converts received line-level signals back into CMOS logic. The MAX3232 belongs to the interface IC and RS-232 transceiver hierarchy, using an on-chip dual charge-pump circuit to generate the positive and negative voltages required by true RS-232 operation. This makes it suitable for industrial control, instrumentation, point-of-sale equipment, and legacy serial-port systems. Key features include a 3 V to 5.5 V supply range, full-duplex operation with two drivers and two receivers, and data rates up to 250 kbps according to the manufacturer product information. The device also provides ±15-kV ESD protection on the serial-port connection terminals and uses external 0.1 µF charge-pump capacitors. Its low-voltage operation reduces the power burden compared with traditional ±5 V or ±12 V RS-232 implementations. The internal charge-pump circuitry generates the bipolar voltages required to meet TIA/EIA-232-F electrical requirements. Because the charge pump switches internally, PCB layout must keep the charge-pump capacitors close to their designated pins and preserve adequate routing away from sensitive analog or communication circuits. The receiver includes hysteresis, which helps reject noise and prevents excessive output chatter as an input signal crosses the logic threshold. Typical applications include legacy RS-232 ports on industrial controllers, test and measurement equipment, programmable logic controllers, security systems, and computer peripherals. The part is particularly useful where a modern 3.3 V or 5 V controller must communicate with an RS-232 device through a DB9 or equivalent connector. The principal design trade-off is that the MAX3232IPWRG4 is a mature RS-232 interface rather than a modern USB-to-serial bridge. It requires external charge-pump capacitors, a suitable connector, and careful treatment of the exposed cable-side pins. Its industrial temperature grade supports equipment intended for a wider operating environment than commercial-temperature parts. This product record combines manufacturer specifications, exact package information, lifecycle status, source links, and verified substitute information to support component selection. Engineers can use the comparison table and replacement notes to determine whether an alternative preserves the TSSOP-16 footprint, supply range, channel count, and RS-232 operating characteristics.

Permintaan RFG Kontak