Produk (46.000+)

MAX3243EAI+TG1Z - 3.3V RS-232 Transceiver | Analog Devices
MAX3243EAI+TG1Z

MAX3243EAI+TG1Z - 3.3V RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EAI+TG1Z is a 3-transmitter, 5-receiver RS-232 communications interface IC operating from +3 V to +5.5 V, supplied in a 28-pin SSOP package. The family supports EIA/TIA-232 and V.28/V.24 communications, automatic shutdown and wakeup behavior, high-data-rate operation, and enhanced electrostatic-discharge protection. Its 1 A supply-current rating identifies it as the MAX3243E family member suited to multi-port RS-232 equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level voltages. It belongs to the transceiver class within interface ICs and ultimately to the broader semiconductor and wired-communications hierarchy. The MAX3243 combines three transmitters, five receivers, and an always-active receiver designed for external monitoring, reducing the number of separate interface devices required in multi-channel equipment. Principal features include three powered drivers, five receiver channels, operation from a 3 V supply, automatic shutdown and wakeup functions, and enhanced ESD protection. The automatic power-control functions help a system reduce consumption when the communication port is idle, while the always-active receiver permits continuous monitoring of an external RS-232 connection. These functions are especially useful in industrial controllers, test equipment, and embedded systems that combine communication and low-power operating modes. The MAX3243E family is built for bidirectional point-to-point serial links using the EIA/TIA-232 standard. Each transmitter provides the voltage swing required by an RS-232 receiver, and each receiver translates the bipolar line voltage into a compatible digital signal. The interface operates from the same 3 V to 5.5 V supply range used by many modern embedded processors, reducing the need for a separate high-voltage interface supply. Exact data-rate, slew-rate, propagation-delay, and channel-isolation limits should be taken from the manufacturer datasheet for the selected temperature and supply conditions. Typical applications include multi-port RS-232 instrumentation, industrial serial controllers, data-acquisition equipment, point-of-sale terminals, and service interfaces for embedded systems. The five receivers are useful when the product must monitor more than one incoming RS-232 signal, while three transmitters support several outbound connections. In portable or industrial equipment, automatic shutdown and wakeup can help control current use when no active peer device is present on the bus. PCB design should preserve the RS-232 interface’s intended impedance and noise behavior, with short connections between the transceiver, protection network, connector, and ground structure. Place the interface-supply decoupling capacitor close to the device and route high-current return paths away from sensitive logic. Before a board revision, verify every signal, enable, and supply connection against the manufacturer pin-description table for the 28-pin SSOP variant. This page combines the manufacturer’s family-level capabilities with exact package and ordering information for MAX3243EAI+TG1Z, then adds application guidance, design checks, and compatible family references. It is intended to help engineers confirm supply compatibility, channel count, package reuse, and the design implications of automatic RS-232 shutdown before releasing a PCB or production build.

Permintaan RFG Kontak
MAX3243ECAI+ - 3V/5V 250kbps RS-232 Transceiver
MAX3243ECAI+

MAX3243ECAI+ - 3V/5V 250kbps RS-232 Transceiver

The Maxim Integrated MAX3243ECAI+ is a 3V-powered EIA/TIA-232 and V.28/V.24 communications interface with three drivers, five receivers, automatic shutdown/wakeup, high data-rate operation, and enhanced electrostatic-discharge protection. It operates from 3.0V to 5.5V and supports data rates up to 250kbps. The device is packaged in a 28-pin SSOP, making it suitable for compact RS-232 equipment designs. An RS-232 transceiver is an interface IC that converts between digital logic-level signals and RS-232 voltage levels. The MAX3243 family belongs to the interface-IC hierarchy and is used where a UART or other digital controller must communicate with a PC, terminal, modem, or other RS-232 equipment. Its multiple drivers and receivers support both standard serial links and additional status or control signals. Key features include automatic shutdown when no valid receiver signal is detected, automatic wakeup when a valid signal returns, and enhanced ESD protection. The manufacturer describes protection to ±15kV using the air-gap discharge test and ±8kV using the contact-discharge test. The available data also identifies the device as a 3/5 transceiver with a 250kbps data-rate capability. The MAX3243E architecture is intended for low-power serial-interface systems. Automatic shutdown can reduce supply consumption when the RS-232 connection is idle, while wakeup allows the interface to reactivate without a continuously active supply state. The device is designed for 3V-powered equipment where RS-232 voltage generation and signal conditioning are required despite low logic supply voltage. Typical applications include PC serial-port interfaces, industrial control equipment, data acquisition systems, point-of-sale terminals, and embedded serial adapters. The combination of multiple drivers, five receivers, automatic power management, and ESD protection supports both data transfer and hardware status signaling in compact embedded systems. Designers should verify the exact pin assignments, external charge-pump capacitors, logic levels, and RS-232 line requirements against the manufacturer datasheet. PCB layout should keep the interface traces short, provide suitable return paths, and account for the elevated RS-232 voltage levels at the driver outputs.

Permintaan RFG Kontak
MAX3243ECAI+G1Z - 3/5 RS-232 Transceiver | Analog Devices
MAX3243ECAI+G1Z

MAX3243ECAI+G1Z - 3/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243ECAI+G1Z is a 3-driver, 5-receiver RS-232 transceiver operating from 3.0 V to 5.5 V, supporting data rates up to 250 kbps in a 28-pin SSOP package. It combines three EIA/TIA-232 transmitters, five receivers, automatic shutdown and wake-up behavior, and enhanced electrostatic-discharge protection for robust serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level UART signals into differential-voltage RS-232 levels and converts incoming RS-232 signals back into CMOS-compatible logic. In the signal-chain hierarchy, the MAX3243 belongs to the RS-232 interface transceiver family, within interface ICs and broader communication semiconductors. Its multi-channel organization allows one device to support several data and control lines while reducing package count and PCB area. The MAX3243 family supports operation from 3.0 V to 5.5 V, enabling use in both 3.3 V and 5 V systems. Its maximum signaling rate is 250 kbps, and the on-board charge-pump transmitter circuitry provides the voltage levels required by RS-232 links. Automatic shutdown reduces supply current to approximately 1 microampere when no valid receiver activity is detected, while wake-up operation restores normal operation when a valid signal returns. Enhanced ESD protection is a defining feature of this interface family. According to the manufacturer datasheet, transmitter outputs and receiver inputs are protected to plus or minus 15 kV using the IEC 1000-4-2 air-gap discharge test and to plus or minus 8 kV using the IEC 1000-4-2 contact-discharge test. These ratings are relevant for cables exposed to electrostatic discharge, although the complete system still requires suitable grounding and board-layout practices. Typical applications include industrial serial-port equipment, data-acquisition systems, instrumentation, point-of-sale terminals, and embedded control modules that need several RS-232 channels. The three transmitters support outbound data, modem-control, or handshake signals, while the five receivers support inbound data, status, and monitoring lines. The complementary always-active receiver provides external monitoring when the main receiver circuitry is shut down. When implementing the MAX3243ECAI+G1Z, follow the manufacturer pin-description and typical-application circuits for supply bypassing, charge-pump capacitors, and connector-side protection. Keep RS-232 traces away from sensitive analog signals, provide a low-impedance ground path, and verify that every connected cable signal remains within the device's absolute-maximum ratings. This product data combines manufacturer specifications, package and channel-count details, application guidance, and verified drop-in alternatives. It also highlights the differences that matter when deciding whether another MAX3243 order code can replace the target without changing the PCB footprint.

Permintaan RFG Kontak
MAX3243ECAI+T - 3/5 RS-232 Transceiver, 15kV ESD | Analog Devices
MAX3243ECAI+T

MAX3243ECAI+T - 3/5 RS-232 Transceiver, 15kV ESD | Analog Devices

The Analog Devices MAX3243ECAI+T is a 3-driver, 5-receiver RS-232 transceiver operating from 3.0V to 5.5V, supporting data rates up to 250kbps and providing ±15kV ESD protection on serial-port pins. The device is packaged in a 28-pin SSOP and includes AutoShutdown and automatic wake-up functions to reduce supply current when no valid receiver activity is detected. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and RS-232 differential line drivers and receivers. The MAX3243 belongs to the hierarchy of interface ICs, serial-interface transceivers, RS-232 communications devices, and semiconductors. It allows a modern low-voltage controller to communicate with legacy RS-232 equipment without requiring external ±12V power rails. The MAX3243 integrates three RS-232 line drivers, five receivers, and a dual charge-pump circuit. Its 3.0V-to-5.5V single-supply operation supports both 3.3V and 5V systems. An internal charge pump generates the bipolar voltage required by RS-232 transmitters, while enhanced electrostatic-discharge protection improves resilience when cables are connected to external equipment. The E suffix identifies the enhanced ESD version, and the CAI suffix denotes the 28-pin SSOP configuration with a commercial temperature grade. Automatic shutdown is a significant benefit in portable and low-power equipment. According to the manufacturer product page, the MAX3243 can reach a 1µA supply current when AutoShutdown is active and no valid signal appears at the receiver inputs. The device can wake automatically when receiver activity resumes, or shutdown can be controlled in software, allowing the interface to remain transparent to normal serial-port operation. Typical uses include industrial serial adapters, point-of-sale equipment, data-acquisition systems, test instrumentation, and embedded controllers that must connect to RS-232 peripherals. Three drivers allow transmission on as many as three lines, while five receivers support monitoring of five incoming signals. The 250kbps capability exceeds the speed required by many legacy serial protocols and is useful for short-distance point-to-point links. PCB design should keep charge-pump and high-voltage driver traces away from sensitive receiver and logic-ground paths. Place the required bypass capacitors close to their supply and ground pins, route connector-side signals according to the manufacturer pinout, and provide chassis grounding or surge-protection components where cables leave the enclosure. Confirm the receiver's active polarity and AutoShutdown timing in firmware before replacing a conventional RS-232 implementation. This product record combines the manufacturer specifications, exact-package identification, lifecycle information, sourcing context, and drop-in alternatives with practical guidance for layout, power management, and signal-integrity review.

Permintaan RFG Kontak
MAX3243ECDB - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243ECDB

MAX3243ECDB - 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243ECDB is a 3-to-5.5-V multichannel RS-232 line driver and receiver providing three drivers, five receivers, and a dual charge-pump circuit in a 28-pin SSOP package. It supports data rates up to 250 kbps and includes ±15 kV ESD protection for HBM and IEC61000-4-2 air-gap discharge, plus ±8 kV IEC61000-4-2 contact-discharge protection on serial-port connection pins. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a cable-based serial port. It belongs to the hierarchy of interface ICs, serial transceivers, and communication-interface semiconductors. The MAX3243ECDB implements the electrical interface required by TIA/EIA-232-F while operating from a single 3-to-5.5-V supply, eliminating the need for a separate bipolar power rail in many applications. The device combines three RS-232 drivers, five receivers, and automatic direction control through on-chip charge pumps. Its 250-kbps capability supports asynchronous data links while its 3-to-5.5-V supply range accommodates both 3.3-V and 5-V system rails. ESD ratings of ±15 kV on HBM and air-gap discharge, and ±8 kV on contact discharge, improve protection where cables connect to user-accessible equipment. The MAX3243E device architecture supports the electrical interface between an asynchronous communication controller and a personal computer or terminal. The integrated charge-pump circuitry generates the RS-232 bipolar voltage levels required by the drivers from the low-voltage system supply. This integration reduces board area by removing external charge-pump capacitors while preserving the required interface voltage swing. Typical uses include industrial serial consoles, data-acquisition equipment, instrumentation, point-of-sale terminals, and embedded systems that need more receivers than drivers. The five receiver channels support monitoring of several status signals, while three driver channels handle transmit, request-to-send, and data-ready control lines. A 28-pin SSOP is useful when the interface density must remain higher than a 16-pin SOIC can accommodate. When laying out this transceiver, route each connector-side signal away from logic and clock traces, and place the charge-pump capacitor and interface bypass capacitors close to their specified pins. Confirm that the selected cable-side baud rate is supported by the 250-kbps device rating and that firmware honors the receiver and driver channel assignments shown in the manufacturer datasheet.

Permintaan RFG Kontak
MAX3243ECDBG4 - 500kbps RS-232 IC | Texas Instruments
MAX3243ECDBG4

MAX3243ECDBG4 - 500kbps RS-232 IC | Texas Instruments

Texas Instruments MAX3243ECDBG4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver operating at up to 500 kbps, with ±15 kV IEC ESD protection and a 28-pin SSOP package. The commercial-temperature ordering option supports system designs requiring a compact multichannel RS-232 interface operating from 0°C to 70°C. An RS-232 line transceiver combines driver and receiver functions for connecting logic-level equipment to a serial port. The driver converts low-voltage logic signals into RS-232-compatible levels, while the receiver converts incoming differential or single-ended serial signals back into logic levels. This transceiver category belongs to the interface IC hierarchy: RS-232 transceiver → interface IC → semiconductor. It is useful when a system needs more than one serial channel, particularly in data acquisition, control, industrial communications, and legacy peripheral equipment. Key features of the MAX3243ECDBG4 include a 3 V to 5.5 V supply range, multichannel RS-232 operation, data rates up to 500 kbps, and ±15 kV IEC ESD protection. The protection rating helps improve system resilience when the serial connector is exposed to electrostatic discharge, although board-level layout, grounding, and connector shielding remain important parts of an effective ESD strategy. The MAX3243E family is designed for compatible with EIA-232 communication requirements and is suitable for systems that need multiple RS-232 drivers and receivers in one package. Its integrated multichannel arrangement reduces the number of separate transceiver packages required on a communications board while conserving board area and simplifying the connection of several serial ports. Typical applications include industrial control systems, laboratory data loggers, POS terminals, embedded instrumentation, and host systems that connect to legacy RS-232 peripherals. The 500 kbps capability supports substantially faster serial links than a conventional low-speed RS-232 port, while the 3 V to 5.5 V supply range allows use with both 3.3 V and 5 V system rails. Designers should follow the manufacturer datasheet for charge-pump capacitor selection, supply decoupling, driver and receiver pin assignments, and exposed-circuit details. Because the MAX3243ECDBG4 uses a narrow-body SSOP package, PCB layout should provide adequate copper and solder-joint area for reliable assembly. This product page consolidates the device function, operating limits, protection rating, package information, sourcing path, and design considerations into one engineering reference. It also identifies genuinely relevant replacement questions and emphasizes direct-footprint verification instead of treating every RS-232 transceiver as a drop-in substitute.

Permintaan RFG Kontak
MAX3243ECDBR - 3/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3243ECDBR

MAX3243ECDBR - 3/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3243ECDBR is a 3-to-5.5-V multichannel RS-232 line driver and receiver providing three drivers, five receivers, and a dual charge-pump circuit in a 28-pin SSOP package. It supports data rates up to 250 kbps and includes ±15 kV ESD protection for HBM and IEC61000-4-2 air-gap discharge, plus ±8 kV IEC61000-4-2 contact-discharge protection on serial-port connection pins. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a cable-based serial port. It belongs to the hierarchy of interface ICs, serial transceivers, and communication-interface semiconductors. The MAX3243ECDBR implements the electrical interface required by TIA/EIA-232-F while operating from a single 3-to-5.5-V supply, eliminating the need for a separate bipolar power rail in many applications. The device combines three RS-232 drivers, five receivers, and automatic direction control through on-chip charge pumps. Its 250-kbps capability supports asynchronous data links while its 3-to-5.5-V supply range accommodates both 3.3-V and 5-V system rails. ESD ratings of ±15 kV on HBM and air-gap discharge, and ±8 kV on contact discharge, improve protection where cables connect to user-accessible equipment. The MAX3243E device architecture supports the electrical interface between an asynchronous communication controller and a personal computer or terminal. The integrated charge-pump circuitry generates the RS-232 bipolar voltage levels required by the drivers from the low-voltage system supply. This integration reduces board area by removing external charge-pump capacitors while preserving the required interface voltage swing. Typical uses include industrial serial consoles, data-acquisition equipment, instrumentation, point-of-sale terminals, and embedded systems that need more receivers than drivers. The five receiver channels support monitoring of several status signals, while three driver channels handle transmit, request-to-send, and data-ready control lines. A 28-pin SSOP is useful when the interface density must remain higher than a 16-pin SOIC can accommodate. When laying out this transceiver, route each connector-side signal away from logic and clock traces, and place the charge-pump capacitor and interface bypass capacitors close to their specified pins. Confirm that the selected cable-side baud rate is supported by the 250-kbps device rating and that firmware honors the receiver and driver channel assignments shown in the manufacturer datasheet.

Permintaan RFG Kontak
MAX3243ECDW - 3/5 RS-232 Transceiver, 500 kbps | Texas Instruments
MAX3243ECDW

MAX3243ECDW - 3/5 RS-232 Transceiver, 500 kbps | Texas Instruments

Texas Instruments MAX3243ECDW is a 3-driver, 5-receiver RS-232 transceiver operating from 3 V to 5.5 V at data rates up to 500 kbps, packaged in a 28-pin SOIC (DW). The device integrates three RS-232 line drivers and five receivers, including a complementary always-active receiver for external monitoring. Its protected I/O pins provide ±15 kV IEC ESD protection, making it suitable for industrial, communications, and data-processing equipment exposed to electrostatic discharge. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy alongside signal conditioners, level translators, and isolated communication interfaces. Unlike a modern differential or differential-based communications standard, RS-232 uses single-ended signaling and is intended principally for point-to-point, short-distance equipment interconnects. Key features include a 3 V to 5.5 V supply range, 500 kbps maximum signaling rate, three transmit channels, five receive channels, and ±15 kV IEC ESD protection. The MAX3243E device family also incorporates power-management features intended to reduce power consumption when communication is not required. Its 28-pin SOIC package provides a conventional surface-mount interface for industrial control systems, POS terminals, data acquisition equipment, and service interfaces. Technically, the MAX3243ECDW combines charge-pump level shifting, RS-232 drivers, and receive channels in one package. The driver channels present bipolar RS-232 output levels, while the receivers include threshold and hysteresis characteristics designed for dependable operation with the voltage swings used by RS-232 links. The manufacturer identifies the MAX3243 family as production and specifies operation from 0°C to 70°C for the MAX3243ECDW ordering option. Typical uses include industrial serial controllers, instrumentation links, printer or terminal interfaces, programmable logic controller communications, and embedded systems requiring more receive channels than transmit channels. For designs with equal numbers of transmit and receive paths, a two-driver, two-receiver transceiver may be more economical. The five receivers also support monitoring paths, status inputs, or one primary link plus additional receive-only connections. PCB design should preserve the short, direct routing associated with high-speed RS-232 transceivers, follow the manufacturer pin and bypass-capacitor recommendations, and provide appropriate return paths for each interface. Keep exposed connector and cable-side circuitry away from sensitive logic, and design enclosure and signal routing so externally accessible lines receive suitable ESD protection and common-mode margin.

Permintaan RFG Kontak
MAX3243ECDWR - 500kbps 3-5.5V RS-232 Transceiver | Texas Instruments
MAX3243ECDWR

MAX3243ECDWR - 500kbps 3-5.5V RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243ECDWR is a 3 V to 5.5 V multichannel RS-232 line driver and receiver supporting data rates up to 500 kbps, with ±15 kV IEC ESD protection on serial-port connection pins. The device contains three line drivers, five line receivers, and a dual charge-pump circuit, and is housed in a 28-pin SOIC (DW) package. Its specified operating temperature range is 0°C to 70°C. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC category and provides the physical signaling layer between an asynchronous communication controller and a serial-port connection. The MAX3243E is designed for equipment that needs multiple RS-232 channels without requiring a separate external voltage-conversion circuit. The MAX3243ECDWR operates from a 3 V to 5.5 V supply, allowing it to work with both 3.3 V and 5 V system rails. Its internal dual charge-pump circuit supports the positive and negative voltage levels required by RS-232. According to the manufacturer datasheet, the serial-port connection pins provide ±15 kV ESD protection under HBM and IEC 61000-4-2 air-gap discharge conditions, plus ±8 kV under IEC 61000-4-2 contact discharge conditions. The integrated charge-pump design reduces the external component count compared with an RS-232 implementation that relies on a separate external supply. Three driver channels can transmit logic signals, while five receiver channels can independently receive serial data. The device supports communication rates up to 500 kbps and meets the electrical requirements stated in the manufacturer documentation for TIA/EIA-232-F operation. Typical uses include industrial serial-port equipment, data-collection systems, point-of-sale terminals, laboratory instrumentation, and embedded control systems. A five-receiver arrangement is useful when a system monitors several RS-232 sources, while the three-driver arrangement supports multiple outbound serial links. The 28-pin SOIC package also simplifies assembly for designs requiring a conventional surface-mount footprint. Layout should keep charge-pump and interface routing away from sensitive analog or high-speed digital paths. Follow the manufacturer datasheet for recommended capacitor placement, serial-interface routing, and power-supply decoupling. Confirm the system ground arrangement and RS-232 connector protection requirements before finalizing a production board. This product page organizes the key electrical ratings, package details, RS-232 interface functions, ESD levels, and application guidance for the MAX3243ECDWR. It also identifies where additional design information, such as exact package dimensions and complete pin descriptions, should be taken directly from the manufacturer documentation.

Permintaan RFG Kontak
MAX3243ECPW - 500kbps RS-232 Transceiver | Texas Instruments
MAX3243ECPW

MAX3243ECPW - 500kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243ECPW is a 3 V to 5.5 V multichannel RS-232 line driver and receiver capable of operation at 500 kbps, with three drivers, five receivers, and a 28-pin TSSOP package. Its serial-port pins provide ±15 kV ESD protection for HBM, IEC 61000-4-2 air-gap discharge, and ±8 kV IEC 61000-4-2 contact-discharge conditions. The device also includes a dual charge-pump circuit that converts the supply into the bipolar voltage required by RS-232 line drivers. An RS-232 transceiver is an interface IC that converts logic-level signals from a host or controller into RS-232-compatible levels, while receiving and converting remote RS-232 signals back into CMOS-compatible logic. The MAX3243E belongs to the RS-232 interface family within the broader interface-IC and semiconductor hierarchy. Its three-driver, five-receiver arrangement supports asymmetrical data flows, such as a PC serial port receiving five incoming lines while transmitting on three lines. Key features include a 3 V to 5.5 V supply range, 500 kbps operation, three RS-232 drivers, five RS-232 receivers, and enhanced ESD protection on the serial connections. The 500 kbps capability makes the device suitable for legacy serial peripherals, industrial controllers, data-acquisition equipment, and embedded systems that still use RS-232 links. The five receivers also allow multiple status or handshake inputs without requiring additional transceiver channels. The integrated charge-pump architecture generates the positive and negative voltage swings required by the RS-232 interface while allowing operation from a single low-voltage supply. The MAX3243E meets the requirements of TIA/EIA-232-F. Control functions support low-power interface management, and the device is intended for systems that require a compact multichannel solution rather than several separate single-channel transceivers. Typical applications include industrial serial controllers, laboratory data loggers, programmable instrumentation, point-of-sale systems, security equipment, and embedded control boards. In these systems, the device can connect a microcontroller or UART to a DB9, RJ45-based, or board-level RS-232 connector. Selection should account for signal polarity, automatic shutdown requirements, cable length, and the electrical protection requirements of the connected port. Place the charge-pump capacitors and interface bypass capacitors close to their designated pins, and route driver outputs and receiver inputs away from sensitive digital clocks. Keep the RS-232 connector-side traces away from low-level analog inputs to minimize capacitive coupling. Confirm the exact connector mapping, enable polarity, and shutdown behavior against the manufacturer datasheet before finalizing a new PCB. This page combines manufacturer specifications, lifecycle information, package details, and application-oriented guidance for engineers assessing the MAX3243ECPW as a multichannel RS-232 interface. The MAX3243ECPW is marked no longer in production by Texas Instruments, so lifecycle planning and sourcing continuity are central considerations for new and legacy designs.

Permintaan RFG Kontak
MAX3243ECPWE4 - 3.3V/5V 3:5 RS-232 Transceiver | TI
MAX3243ECPWE4

MAX3243ECPWE4 - 3.3V/5V 3:5 RS-232 Transceiver | TI

The Texas Instruments MAX3243ECPWE4 is a 3.3V/5V multichannel RS-232 line driver and receiver with three drivers and five receivers in a 28-pin TSSOP package. It supports a 3V to 5.5V supply range, operates from a 3.6V supply in the cited configuration, and provides ±15kV HBM electrostatic-discharge protection on the RS-232 interface. The device is specified as a commercial-temperature-grade, gull-wing surface-mount component. An RS-232 interface transceiver is an interface IC that combines digital logic-level line drivers and receivers with the voltage levels required by the RS-232 standard. This conversion allows a low-voltage controller, computer, or test instrument to communicate over a longer-distance, single-ended serial link. The MAX3243ECPWE4 belongs to the RS-232 transceiver family within interface ICs and combines three transmit channels with five receive channels. Key features include its 3V to 5.5V operating supply, three transmit and five receive channels, and a 150ns receiver propagation delay. Its ±15kV HBM ESD protection improves tolerance of connector-borne electrostatic discharge, an important consideration when the interface connects to external equipment through a cable. The 28-terminal TSSOP also supports compact, high-density PCB layouts while retaining gull-wing leads for inspection and assembly. The MAX3243 uses charge-pump-assisted RS-232 interface circuitry to generate the bipolar voltage levels required by RS-232 communication. The three-driver/five-receiver arrangement is useful when a system needs more receive channels than transmit channels, such as multiport instrumentation, industrial controllers, or data-acquisition equipment. Its 150ns receive delay is suitable for standard asynchronous serial interfaces where the overall system must still meet the receiver timing requirements of the connected protocol. Typical applications include industrial serial-port adapters, RS-232 test equipment, point-of-sale terminals, barcode scanners, industrial control panels, and embedded instrumentation. The part can also support mixed transmit-and-receive ports in systems where one host must monitor several incoming devices. The 3.3V-compatible supply range allows operation from modern low-voltage digital rails without requiring a separate 5V transceiver. When laying out the circuit, place charge-pump capacitors and interface bypass capacitors close to their associated pins, and route each driver output directly to its connector-side protection network. Keep sensitive receiver traces away from clocking, switching-converter, and high-current return paths to minimize noise pickup. Confirm that the connector-side network satisfies the applicable RS-232 and ESD requirements for the final system. This product page combines the exact MAX3243ECPWE4 package, supply, protection, channel-count, and timing specifications with verified sourcing links, qualified replacement guidance, and practical PCB-design notes. The comparison and selection information is intended to help engineers assess footprint, temperature grade, and interface requirements before committing a 28-pin TSSOP design to production.

Permintaan RFG Kontak
MAX3243ECRHBR - 3/5 RS-232 Transceiver, 500kbps, 32-VQFN | TI
MAX3243ECRHBR

MAX3243ECRHBR - 3/5 RS-232 Transceiver, 500kbps, 32-VQFN | TI

The Texas Instruments MAX3243ECRHBR is a 3 V to 5.5 V multichannel RS-232 line driver/receiver IC providing three drivers, five receivers, and a dual charge-pump supply in a 32-pin VQFN (5 mm x 5 mm) surface-mount package. It supports data rates up to 500 kbps and is qualified for operation from 0 °C to 70 °C. An RS-232 transceiver is a bidirectional interface IC that converts logic-level TTL/CMOS signals into RS-232 level voltages on transmit and back into logic levels on receive. Within the power-management and interface hierarchy, the MAX3243E family sits at the physical-layer boundary between a host UART and a cable-attached peripheral, adding level translation, noise immunity, and electrostatic-discharge (ESD) hardening that a bare UART driver pair cannot provide. Key features of the MAX3243ECRHBR include ±15 kV ESD protection on all serial pins under the human body model (HBM), ±15 kV air-gap and ±8 kV contact discharge per IEC 61000-4-2, a dual on-chip charge pump that generates the bipolar RS-232 levels from a single supply, and a 3-to-5.5 V operating range that allows direct interfacing with 3.3 V and 5 V host logic without level shifters. A single-channel shutdown pin places the device in a low-power state when the port is idle. Architecturally, the device splits its channels asymmetrically: three drivers share the charge-pump rails for a typical transmit group, while five receivers provide more receive inputs than there are transmit outputs. This suits equipment where the host must listen to several peripherals but only drives one or two lines, such as multi-drop industrial terminals and POS equipment. The wide common-mode range of the receivers allows them to interpret RS-232 signals referenced to ground even when the two ends of a long cable sit at different ground potentials. Typical applications include industrial serial consoles, barcode scanners, weighing scales, laboratory instrument control ports, point-of-sale terminals, and battery-powered handheld peripherals that still require a hardened RS-232 port. The small 5 mm square VQFN footprint also makes the device attractive for space-constrained handheld and portable designs where a TSSOP would be too long for the board outline. When laying out this device, place the charge-pump flying capacitors and the RS-232 line-side protection network close to the device, and route the driver outputs directly to the connector with a common-ground return path. Use the pin-description table in the manufacturer datasheet to assign logic-side and line-side nets, and confirm the VQFN exposed-pad soldering and thermal requirements in the package drawing section.

Permintaan RFG Kontak
MAX3243ECUI+ 3V 5.5V 250kbps RS-232 Transceiver | ADI
MAX3243ECUI+

MAX3243ECUI+ 3V 5.5V 250kbps RS-232 Transceiver | ADI

Analog Devices MAX3243ECUI+ is a 3-to-5.5 V RS-232 transceiver with three transmitter channels, five receiver channels, 250 kbps data rate, ±15 kV ESD protection, and automatic shutdown in a 28-pin TSSOP package. The part is designed for equipment that requires multiple RS-232 ports while operating from either 3 V or 5.5 V supplies. An RS-232 transceiver is a line-driver and line-receiver interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. In the interface hierarchy, the MAX3243ECUI+ belongs to the communication-interface IC family, combining RS-232 drivers and receivers with low-voltage digital support and protected external connections. Key electrical features include operation from 3.0 V to 5.5 V, a maximum data rate of 250 kbps, and ±15 kV ESD protection on the serial interfaces. Automatic shutdown reduces supply consumption when the associated RS-232 links are inactive, while the complementary always-active receiver supports continuous monitoring. The 28-pin TSSOP package provides a compact surface-mount footprint for industrial control, communications, instrumentation, and embedded equipment. The three drivers accommodate outbound serial connections, while five receivers provide additional inbound monitoring channels. This asymmetric 3/5 arrangement is useful in systems where several remote devices report status to one controller while the controller drives a smaller number of commands. The 250 kbps maximum data rate supports moderate-speed point-to-point serial links and legacy peripheral communication. Typical uses include industrial controllers, data-acquisition equipment, POS terminals, test systems, and service interfaces. In an industrial controller, the device can connect a local processor to multiple RS-232 sensors or service ports while its ESD-protected lines improve resilience to electrostatic discharge encountered during installation and maintenance. PCB design should place the device close to its RS-232 connector and route driver and receiver traces away from clocks, switching regulators, and high-speed digital signals. Confirm that connector-side protection and grounding provide the intended surge and ESD path, and follow the manufacturer datasheet for recommended charge-pump capacitors and layout. This page combines the manufacturer specifications, package details, engineering applications, drop-in alternatives, comparison parameters, and practical design guidance to help engineers evaluate the MAX3243ECUI+ for new and existing RS-232 designs.

Permintaan RFG Kontak
MAX3243ECUI+T - 3/5 RS-232 Transceiver | Analog Devices
MAX3243ECUI+T

MAX3243ECUI+T - 3/5 RS-232 Transceiver | Analog Devices

Analog Devices MAX3243ECUI+T is a 3-driver, 5-receiver RS-232 transceiver with a 250 kbps data rate, 3.0 V to 5.5 V supply range, ±15 kV ESD protection, and a 28-pin TSSOP package. It combines three transmit channels, five receive channels, low-power AutoShutdown, and supply current as low as 1 µA for portable and industrial serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. In the product hierarchy, the MAX3243 belongs to the RS-232 transceiver class, then to line-driver and receiver ICs, then to interface ICs and semiconductors. This multi-channel device reduces the number of discrete interface packages required when several serial ports share one controller. The MAX3243 operates from 3.0 V to 5.5 V, allowing operation from either 3.3 V or 5 V system rails. Its three drivers and five receivers support asymmetric port counts common in console, diagnostic, instrumentation, and embedded-control equipment. AutoShutdown disables the internal supply and drivers when the receiver inputs do not detect a valid signal level, reducing standby consumption to approximately 1 µA when supported by the selected power configuration. The interface provides ±15 kV ESD protection according to the device description, improving tolerance to electrostatic discharge at externally accessible serial connectors. The 250 kbps maximum signaling rate is suitable for legacy RS-232 equipment, industrial consoles, configuration ports, and control links that do not require the throughput of modern differential interfaces. Charge-pump circuitry generates the bipolar voltage required by RS-232 without a separate negative supply. Typical uses include three-port RS-232 console expansion, multi-channel data acquisition, service interfaces in industrial equipment, instrument control ports, and mixed-voltage embedded systems. The 28-pin TSSOP package supports compact surface-mount layouts while providing enough I/O for five receive inputs, three transmit outputs, power, ground, and control functions. PCB design should keep charge-pump capacitors close to their associated pins and route driver outputs and receiver inputs away from sensitive analog circuitry. External protection may still be required for long cables or connectors exposed to severe industrial transients. The receiver inputs should also be checked against the selected operating mode and shutdown behavior before finalizing the system power architecture. This page combines manufacturer specifications, package and interface details, drop-in family options, application guidance, and practical PCB considerations to support faster component selection and replacement planning.

Permintaan RFG Kontak
MAX3243ECWI+ - 3V to 5.5V RS-232 Transceiver | Maxim
MAX3243ECWI+

MAX3243ECWI+ - 3V to 5.5V RS-232 Transceiver | Maxim

The Maxim Integrated MAX3243ECWI+ is a 3V to 5.5V RS-232 transceiver with three transmitters, five receivers, full-duplex operation, and 15 kV ESD protection, housed in a 28-pin SOIC package. It is designed for systems that require multiple RS-232 data channels and low-power operation from a single 3.0V or 5.0V supply. An RS-232 transceiver is an interface IC that combines line drivers, also called transmitters, and line receivers. The MAX3243 family provides three driver outputs and five receiver inputs in one package, allowing several serial ports or multiple logic signals to share a compact RS-232 interface. The MAX3243ECWI+ is intended for industrial, instrumentation, communications, and embedded-control equipment. Key features include a 3.0V to 5.5V operating supply range, 1 uA supply current in shutdown mode, 120 kb/s data-rate capability in the comparison data, and integrated ESD protection rated to 15 kV. AutoShutdown functionality helps reduce system power consumption when the RS-232 interface is not required. The 28-pin SOIC package is a standard surface-mount industrial package. The device uses RS-232 line signaling to translate digital logic levels into differential bipolar voltage levels and back again. The three transmitters support point-to-point serial links, while the five receivers can monitor incoming data or accept additional RS-232 signals. The integrated protection circuitry is particularly useful in industrial environments where cable-connected ports can be exposed to electrostatic discharge. Typical applications include multi-port RS-232 equipment, test and measurement instruments, data acquisition systems, industrial controllers, and embedded serial interfaces. The MAX3243ECWI+ is appropriate when one board needs more than a single RS-232 transmitter and receiver while keeping the power supply below 5.5V. For implementation, verify the supply voltage, confirm that the transceiver is enabled or disabled according to the system power sequence, and provide the required external charge-pump capacitors recommended by the manufacturer datasheet. Place protection and signal-routing components close to the connector and the transceiver to minimize ESD current paths.

Permintaan RFG Kontak
MAX3243ECWI+T - 3/5 RS-232 Transceiver, 250 kbps | Analog Devices
MAX3243ECWI+T

MAX3243ECWI+T - 3/5 RS-232 Transceiver, 250 kbps | Analog Devices

The Analog Devices MAX3243ECWI+T is a 3/5 RS-232 transceiver with three drivers, three receivers, and 250 kbps signaling in a 28-SOIC package. It operates from 3.0 V to 5.5 V, provides ±15 kV ESD protection, and supports automatic shutdown to reduce supply current to 1 µA when no valid receiver signal is detected. AutoShutdown circuitry wakes the device when valid RS-232 activity resumes. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. The MAX3243 belongs to the RS-232 interface transceiver class, combining drivers, receivers, charge-pump support, and low-power management in one device. This integration allows a host controller or test system to communicate with RS-232 equipment over a cable-defined serial interface. Key features include a 3.0 V to 5.5 V supply range, operation up to 250 kbps, full-duplex communication through three transmit and three receive channels, and ±15 kV ESD protection. The 1 µA shutdown supply current helps preserve system energy when the port is idle. The wide 28-SOIC footprint is a practical option for designs requiring more channels than the smaller two- or three-driver transceivers commonly used in compact equipment. The MAX3243 architecture uses integrated level-shifting drivers and receivers to produce and accept RS-232-compatible signal levels from a low-voltage digital supply. Charge-pump circuitry provides the elevated transmitter voltage required by the RS-232 standard. AutoShutdown reduces power consumption when the connected port carries no valid activity, while receiver-side logic allows the host to recognize a returning signal and reactivate the device. Typical uses include industrial serial consoles, automated test equipment, data acquisition systems, instrumentation, point-of-sale terminals, and legacy peripheral connectivity. The 250 kbps capability also suits short-distance board-level links, data acquisition links, and configuration interfaces where the nominal RS-232 limit is lower but faster burst traffic is expected. A critical design consideration is that RS-232 is a point-to-point interface, so each driver should face a single receiver rather than an unterminated multidrop bus. Place transient-protection and connection components where cables enter the enclosure, and confirm that signal levels, ground reference, and cable length satisfy the system communication requirements.

Permintaan RFG Kontak
MAX3243EEAI+ - 3.0V RS-232 Transceiver | Analog Devices
MAX3243EEAI+

MAX3243EEAI+ - 3.0V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EEAI+ is a 3/5-channel RS-232 transceiver designed for full-duplex serial communication, with three drivers, five receivers, a 3.0V to 5.5V supply range, and a 250kbps data rate. The device is housed in a 28-pin SSOP package and includes enhanced 15kV ESD protection on its RS-232 pins. It also provides automatic shutdown and wake-up functions for reducing supply current in portable or intermittently connected systems. An RS-232 transceiver is an interface IC that converts between logic-level digital signals and differential bipolar RS-232 line levels. The MAX3243EEAI+ belongs to the RS-232 transceiver hierarchy, where it combines line drivers, line receivers, charge-pump circuitry, and logic-level control into one communication interface. Its receiver structure supports both an active-low shutdown control and an active-high enhanced-power-management input. Key features include three transmit channels, five receive channels, 250kbps operation, operation from 3.0V to 5.5V, and 15kV ESD protection. The multiple receiver count allows one transmit line to be monitored by several destinations, while the three driver outputs support connections to three RS-232 data buses. Automatic shutdown can reduce power consumption when the connected equipment is inactive. The MAX3243E uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 from a single low-voltage supply. Its enhanced driver design can provide true RS-232 performance at low supply voltages without requiring a 5V-only source. The manufacturer describes the MAX3243E family as 3V-powered EIA/TIA-232 and V.28/V.24 communications interfaces with automatic shutdown, wake-up, high data rates, and enhanced ESD protection. Typical applications include industrial serial controllers, point-of-sale equipment, instrumentation, data-acquisition systems, and communication links between a host and peripheral devices. The three drivers and five receivers are particularly useful when one controller must interface with multiple downstream devices or when received data must be distributed to several logic inputs. For a new design, verify the exact pin functions, shutdown polarity, charge-pump capacitor values, and external communication-line requirements against the Analog Devices MAX3243E datasheet before layout. Keep the RS-232 connector-side traces away from sensitive analog and high-speed digital paths, and place the required charge-pump capacitors close to their specified pins. This product page combines the MAX3243EEAI+ ordering information, RS-232 interface characteristics, package details, compatible alternatives, and practical implementation guidance to support component selection and PCB design decisions.

Permintaan RFG Kontak
MAX3243EEAI+C9V - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EEAI+C9V

MAX3243EEAI+C9V - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EEAI+C9V is a 3/5 RS-232 transceiver with three drivers, five receivers, 3.0V to 5.5V operation, 250kbps data rate, and ±15kV ESD protection in a 28-SSOP package. It also provides 1µA automatic-shutdown operation for low-power serial-port designs. An RS-232 transceiver is an interface IC that combines line drivers and receivers for communicating between digital logic and a serial port using EIA/TIA-232 voltage levels. The MAX3243E family belongs to the transceiver hierarchy, with RS-232 interface ICs forming part of the broader communications-interface semiconductor category. Its three-driver, five-receiver arrangement supports complete serial-port signal paths while reducing the number of discrete interface components required. Key features include a 3.0V to 5.5V supply range, operation up to 250kbps, ±15kV ESD protection, and a low 1µA shutdown current. Automatic shutdown and wakeup help reduce system power when the serial interface is idle. The 28-pin SSOP package is suitable for compact industrial, embedded, instrumentation, and data-communications equipment where board area and standardized surface-mount assembly are important. The MAX3243E architecture uses charge-pump circuitry to generate the bipolar voltage levels required by RS-232 from a single low-voltage supply. Its three drivers and five receivers provide flexible channel allocation for PC-style serial ports. Two receiver outputs remain active during shutdown according to the family description, allowing selected incoming signals to be monitored without keeping the entire interface fully powered. Typical applications include industrial serial adapters, embedded control systems, point-of-sale equipment, test instruments, data-acquisition systems, and legacy peripheral connections. The 3.0V minimum supply allows operation alongside 3.3V system logic, while the 5.5V maximum supports 5V designs. System designers should still verify signal levels, capacitance, line loading, and timing against the particular channel configuration. For PCB implementation, place charge-pump capacitors and interface bypass capacitors close to their associated pins, keep the RS-232 connector-side traces away from sensitive analog and clock paths, and provide adequate return-current paths. Confirm the device's charge-pump capacitor values and stability requirements in the manufacturer datasheet before releasing the layout. This page organizes the key electrical characteristics, drop-in alternatives, application guidance, comparison data, and practical layout considerations needed to evaluate the MAX3243EEAI+C9V for a new RS-232 interface design.

Permintaan RFG Kontak
MAX3243EEAI+G071 - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EEAI+G071

MAX3243EEAI+G071 - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EEAI+G071 is a 3.0V to 5.5V RS-232 interface transceiver with a 250kbps data rate, ±15kV ESD protection, and a 28-pin SSOP package. The MAX3243EEAI family combines four drivers and four receivers with automatic shutdown and wake-up capability for reliable, low-power serial communication. An RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back to logic levels. In the hierarchy of electronic components, it belongs to the interface IC class, specifically the RS-232 transceiver and communications-interface subcategory used to bridge modern digital logic with legacy serial-port equipment. The MAX3243EEAI+G071 operates from a 3.0V to 5.5V supply, supporting both modern 3.3V and 5V systems. Its maximum signaling rate is 250kbps, making it suitable for industrial control links, data acquisition equipment, POS terminals, and service interfaces that require dependable RS-232 communication. Enhanced electrostatic-discharge protection on the RS-232 pins improves resilience to cable-borne transients encountered outside the equipment enclosure. The device family includes automatic shutdown and wake-up functions. These features allow a system to reduce supply consumption when no RS-232 activity is present and restore operation when a valid signal returns. The design combines four transmit channels and four receive channels in one package, reducing board area compared with several smaller interface components while preserving individual channel control. Typical applications include industrial serial controllers, test and measurement instruments, barcode scanners, security equipment, and communication links between a host computer and peripheral equipment. The 250kbps capability supports higher-throughput legacy serial traffic than slower RS-232 transceivers while retaining the voltage-level conversion required by the EIA/TIA-232 interface. PCB design should place the charge-pump capacitors and RS-232 interface components close to their associated IC pins. Keep long RS-232 traces away from clocks, sensitive analog inputs, and switching-supply nodes. Confirm the external capacitor values, supply range, and charge-pump requirements in the manufacturer datasheet before releasing the PCB. This page consolidates the exact package, operating-voltage, data-rate, and ESD characteristics, then adds application guidance, practical layout notes, and qualified same-family drop-in options for engineers evaluating the MAX3243EEAI+G071 for an RS-232 interface design.

Permintaan RFG Kontak
MAX3243EEAI+G1Z - 250kbps RS-232 Transceiver | Maxim
MAX3243EEAI+G1Z

MAX3243EEAI+G1Z - 250kbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3243EEAI+G1Z is a 3-transmitter, 5-receiver RS-232 interface transceiver operating from 3.0 V to 5.5 V, with a maximum data rate of 250 kbps in a 28-pin SSOP package. It provides automatic shutdown and wake-up, low 1 µA supply current, and enhanced electrostatic-discharge protection. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic levels. It belongs to the serial-interface hierarchy: transceiver > RS-232 interface > communications interface > interface IC. This bidirectional signal-conditioning function allows equipment operating at different logic levels to communicate through the EIA/TIA-232 physical interface. The MAX3243EEAI+G1Z combines three driver outputs with five receiver inputs, supporting applications that need multiple receive channels and a smaller number of transmit channels. Its 3.0 V to 5.5 V supply range accommodates modern 3.3 V and 5 V digital systems. The 250 kbps maximum data rate is suitable for moderate-speed serial links, including embedded control, instrumentation, and industrial communications equipment. Automatic shutdown is a defining feature of the MAX3243E family. When no valid receiver signal is detected, the on-board power supply and drivers can shut down to reduce supply current to as little as 1 µA. Automatic wake-up reactivates the interface when valid data returns, reducing system power consumption without requiring host intervention. Enhanced ESD protection strengthens the interface against electrostatic discharge encountered during cable installation or industrial environments. According to the MAX3243EEAI data-sheet description, transmitter outputs and receiver inputs support ±15 kV air-gap discharge and ±8 kV contact-discharge protection. These ratings are relevant to external cable-facing pins and should be considered alongside normal board-layout and grounding practices. Typical uses include RS-232 links in industrial controllers, test equipment, data-acquisition systems, point-of-sale hardware, and embedded serial-port systems. The 28-pin SSOP package is compact, but its lead pitch and thermal behavior require careful PCB planning. Use the manufacturer pin-description table when assigning tracks and confirming the exposed-package or thermal details for the selected ordering code. This page combines the family-level electrical characteristics, exact package identification, sourcing guidance, application fit, and practical design considerations. It also identifies genuine same-family alternatives while making the differences between ordering variants explicit for engineering review.

Permintaan RFG Kontak
MAX3243EEAI+T - 3/5 RS-232 Transceiver, 3-5.5V | Analog Devices
MAX3243EEAI+T

MAX3243EEAI+T - 3/5 RS-232 Transceiver, 3-5.5V | Analog Devices

The Analog Devices MAX3243EEAI+T is a 3-driver, 5-receiver full-duplex RS-232 transceiver operating from 3 V to 5.5 V in a 28-pin SSOP package. It supports data rates up to 250 kbps, includes ±15 kV ESD protection, and draws approximately 1 µA when the AutoShutdown feature has disabled the on-board supply and drivers. An RS-232 transceiver is an interface integrated circuit that converts between single-ended RS-232 line signals and complementary TTL/CMOS logic levels. It belongs to the RS-232 interface transceiver class, within interface ICs and broader semiconductor communication devices. The MAX3243EEAI+T combines three RS-232 drivers and five receivers, including two always-active noninverting receiver outputs for monitoring external signals without waking the main supply section. Principal features include a single 3 V to 5.5 V supply operation, 250 kbps data-rate capability, enhanced electrostatic discharge protection on all transmitter outputs and receiver inputs, and automatic shutdown with automatic wakeup. These characteristics support portable equipment, industrial controllers, data-acquisition systems, and legacy peripheral interfaces that require a direct RS-232 connection. The MAX3243 family uses Maxim Integrated's AutoShutdown architecture to reduce supply consumption when no valid receiver activity is detected. Supply current falls to approximately 1 µA in the shutdown condition, while activity on a receiver input can reactivate the internal supply and drivers. This behavior is useful in battery-powered and intermittently connected systems where an idle RS-232 port should not continue consuming significant power. Typical uses include configuring an embedded controller for legacy printers, industrial instruments, point-of-sale equipment, and service-console connections. The three-driver arrangement supports multiple outbound RS-232 channels, while the five-receiver arrangement provides additional input and monitoring paths. Its 28-pin SSOP package also suits compact boards where connector protection and ESD resilience are important. Design with the MAX3243EEAI+T by following the manufacturer datasheet for charge-pump capacitor selection, receiver-input handling, and supply bypassing. Confirm that every connected driver output meets the intended RS-232 voltage swing and that unused inputs remain in a defined state. Protect externally accessible connectors with the device's ESD capability and route return paths away from sensitive analog or high-speed digital circuitry. This page combines manufacturer specifications, distributor availability references, family-level drop-in alternatives, and application-focused design guidance to support faster component evaluation. It also identifies the temperature-grade and package differences that must be reviewed before assigning an alternative part to an existing PCB.

Permintaan RFG Kontak
MAX3243EETI+ - 250kbps RS-232 IC | Texas Instruments
MAX3243EETI+

MAX3243EETI+ - 250kbps RS-232 IC | Texas Instruments

The Texas Instruments MAX3243EETI+ is a 3 V to 5.5 V multichannel RS-232 line driver and receiver rated for 250 kbps data rates, with ±15 kV ESD protection on its communication pins. The device is offered in a 28-terminal, no-lead square QCCN package and operates in the industrial temperature grade. A low 1 µA supply specification supports power-conscious serial-interface designs. An RS-232 transceiver is an interface IC that combines a line driver, line receiver, and charge-pump voltage conversion in one package. It translates logic-level signals from a host or embedded controller into RS-232 levels and converts received RS-232 signals back to logic levels. Within the broader hierarchy of interface ICs, a multichannel RS-232 transceiver reduces component count, board area, and external voltage-doubling circuitry in multi-port serial systems. The MAX3243EETI+ supports supply voltages from 3 V to 5.5 V, enabling operation in both 3.3 V and 5 V systems. Its 250 kbps maximum data rate suits industrial equipment, data-acquisition equipment, point-of-sale terminals, and instrument-control links. Integrated ±15 kV ESD protection helps protect the external serial interface from electrostatic discharge encountered during installation or connection to cables. The MAX3243 family provides multiple drivers and receivers for RS-232 communication. When using the charge-pump section, the required capacitor arrangement and bypass components should follow the manufacturer datasheet's recommended application circuit. The integrated converter is intended to generate the positive and negative voltages required by RS-232, while the driver and receiver sections perform level conversion and signal conditioning. Typical uses include industrial serial controllers, test equipment, security systems, medical-instrument interfaces, and point-of-sale hardware. The 250 kbps capability is suitable for links that are faster than legacy 9600-bit-per-second ports but do not require the throughput of a modern high-speed differential serial standard. Cable length and signal-integrity requirements should still be checked against the RS-232 electrical limits for the intended operating environment. Place the MAX3243EETI+ close to the connector-side transceiver circuitry, keep the charge-pump capacitor loops compact, and provide a low-impedance ground return for each interface. Confirm logic levels, timing, shutdown behavior, and unused-channel connections in the manufacturer datasheet before releasing the PCB layout. Industrial temperature-grade qualification should also be checked against the complete assembly's environmental requirements. This page consolidates the manufacturer's operating limits, package characteristics, comparison criteria, replacement guidance, and application-oriented design guidance into one engineering reference. It focuses on practical selection and integration decisions rather than repeating only the basic distributor catalog description.

Permintaan RFG Kontak
MAX3243EETI+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EETI+T

MAX3243EETI+T - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EETI+T is a 3-channel RS-232 line driver and receiver operating from a 3V to 5.5V supply at data rates up to 250kbps. The device provides ±15kV electrostatic-discharge protection and uses AutoShutdown to reduce supply current to 1µA when no valid receiver signal is present. It is packaged in a 28-terminal, no-lead square QFN package designated QCCN. A multi-channel RS-232 transceiver combines push-pull line drivers and receivers for bidirectional data transfer between a host and an external serial device. In the broader hierarchy, MAX3243EETI+T is an interface transceiver, an interface IC, and a semiconductor for establishing the physical signal layer required by RS-232 equipment. The AutoShutdown function is particularly useful in battery-powered instruments, portable test equipment, and systems where an inactive serial port must not continue consuming power. The 3V to 5.5V operating range permits operation from both 3.3V and 5V system rails. Its 250kbps maximum signaling rate supports data rates above the traditional 20kbps RS-232 limit while remaining suitable for instrument control, point-of-sale equipment, industrial controllers, and embedded peripheral links. ±15kV ESD protection improves tolerance of connector-borne transients, although it does not eliminate the need for correct board layout and external protection strategy. The MAX3243 family combines low-power supply design with multiple driver and receiver channels. AutoShutdown detects whether valid signal levels appear on receiver inputs and disables the internal supply and drivers when the port is idle. This behavior allows a direct interface to operate from modern low-voltage digital rails without requiring a separate power-control transistor. The exact charge-pump, driver-slew, and receiver-threshold details should be confirmed against the manufacturer datasheet before finalizing a new design. Typical uses include multichannel instrument-control links, data acquisition, barcode and point-of-sale terminals, industrial serial adapters, and embedded systems that exchange RS-232 data with legacy peripherals. The 28-terminal QFN footprint also requires careful PCB planning because its compact leadless geometry leaves less visible inspection area and demands accurate land patterns, solder-paste control, and thermal-via placement. For a robust implementation, keep the MAX3243EETI+T close to the RS-232 connector, route driver and receiver traces away from sensitive analog circuitry, and place charge-pump and interface capacitors at the pins specified by the reference design. Confirm signal polarity, receiver thresholds, shutdown behavior, and grounding with the system-level RS-232 requirements rather than assuming that every ±15V RS-232-compatible product is electrically interchangeable. This page combines manufacturer specifications, package information, practical RS-232 design guidance, and carefully qualified same-family replacement options. It is intended to help engineers determine whether the MAX3243EETI+T fits the required voltage, data rate, channel count, package, and protection level before committing the part to a PCB or production BOM.

Permintaan RFG Kontak
MAX3243EETJ+ - 250kbps RS-232 Transceiver | Analog Devices
MAX3243EETJ+

MAX3243EETJ+ - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EETJ+ is a 3.0V to 5.5V RS-232 transceiver with three drivers and five receivers, automatic shutdown and wakeup, enhanced electrostatic-discharge protection, and a maximum data rate of 250kbps in a 32-pin TQFN package. The interface operates across -40°C to +85°C and provides ±15kV ESD protection. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 differential voltage levels and converts received RS-232 signals back into logic levels. The MAX3243E belongs to the broader hierarchy of interface ICs, serial transceivers, line drivers and receivers, and semiconductor communication components. Its multiple drivers and receivers allow several unidirectional or bidirectional serial links to share one compact device. Key features include three transmit outputs, five receive inputs, a 3.0V to 5.5V supply range, 1µA shutdown behavior, and automatic wakeup. The 250kbps maximum signaling rate supports data acquisition, industrial control, point-of-sale equipment, and embedded serial systems. A ±15kV ESD-rated interface helps protect equipment when connected cables are exposed to electrostatic discharge during installation or maintenance. The MAX3243E is designed for 3V-powered systems and uses automatic shutdown to reduce supply current when no valid signal is present. Automatic wakeup can return the transceiver to an operating state when incoming data resumes, reducing repeated manual enable control. Its three-driver and five-receiver arrangement provides more receive channels than the MAX3221E and MAX3223E family members, making it useful where several status or control signals must be monitored. Typical uses include industrial serial controllers, instrumentation, test and measurement equipment, security systems, and computer peripherals. In a point-of-sale terminal, the three transmitters can drive status indicators or service interfaces while the five receivers monitor keypad, sensor, and handshake signals. In an industrial controller, the device can bridge low-voltage logic and long RS-232 connections while its ESD protection reduces vulnerability to cable-borne transients. Design the circuit with the voltage ratings and external-charge-pump requirements specified in the manufacturer datasheet. Place bypass capacitors close to the supply and charge-pump nodes, route protected RS-232 lines away from sensitive clocks and data traces, and confirm that the connector and cable interface provide the intended ESD and common-mode protection. Verify signal polarity and handshake behavior in software because automatic shutdown and wakeup can affect receiver state at startup. This product page combines the manufacturer’s device specifications with practical RS-232 design guidance, compatible same-family alternatives, and a parameter-by-parameter comparison. It is intended to accelerate component selection while keeping the final engineering decision grounded in the official MAX3243E datasheet.

Permintaan RFG Kontak