IC Antarmuka
Subkategori
Produk (2.300+)
ISL8324IB - Dual 60 Ohm SPST Analog Switch | Renesas
The Renesas ISL8324IB is a dual, single-pole single-throw analog switch with two independently controlled 1:1 circuits, 60 ohm on-resistance, and an 8-SOIC package. According to the distributor data, it operates from a single low-voltage supply and is specified for -40 C to +85 C. These verified facts place it in the low-voltage switching hierarchy: SPST analog switch -> analog switch/multiplexer -> interface IC -> semiconductor. An analog switch connects or discloses a signal path with controlled resistance rather than amplifying or converting it. The ISL8324IB is useful when a sensor, test point, audio path, or measurement input must be routed or isolated while preserving signal integrity. Its two SPST channels provide independent routing control, while the 1:1 topology avoids changing the nominal signal direction when a channel is closed. The verified distributor listing identifies the device as a 2-circuit IC switch with 1:1 configuration, 60 ohm on-resistance, and 8-SOIC packaging. These are the principal selection criteria for PCB compatibility and signal-path loss assessment. The manufacturer datasheet must be consulted for complete input-voltage limits, control-logic levels, leakage, charge injection, bandwidth, and absolute maximum ratings before a design is released. The single-supply architecture simplifies systems that already operate from a low-voltage rail, while the -40 C to +85 C range covers industrial and commercial temperature environments. Engineers should treat control inputs, analog signal amplitudes, supply sequencing, and power dissipation as design constraints rather than assume that a low-voltage-rated switch can accept arbitrary signals. The 8-SOIC footprint is compatible only when the alternative has the same pin arrangement and electrical function. Typical uses include battery-powered sensor interfaces, analog test and measurement equipment, audio routing, data-acquisition front ends, and low-voltage communication interfaces. In a sensor interface, each SPST path can isolate a transducer during measurement or connect it to an amplifier. In test equipment, the switch can provide controlled connectivity between an external fixture and an analog input. In audio routing, the 60 ohm resistance is a relevant insertion-loss and drive-current consideration. A key design practice is to check the complete signal path, including source impedance, switch resistance, leakage, control timing, and downstream input capacitance. The datasheet's logic thresholds and dynamic characteristics should be compared with the controlling device. If replacement is considered, verify package pinout, supply range, on-resistance, control polarity, bandwidth, leakage, and temperature rating rather than relying only on the SOIC outline. This product data combines verified distributor identity, package, switching configuration, resistance, temperature range, cross-reference results, and practical engineering guidance. It is intended to support initial component selection and comparison, while incomplete electrical limits remain explicitly marked for verification rather than guessed.
ISL8325IB - Dual SPST 60Ohm Analog Switch | Renesas
The Renesas Electronics ISL8325IB is a low-voltage, single-supply, dual SPST analog switch with two independently controlled 1:1 circuits, an on-resistance of 60 ohms, and an 8-pin SOIC package. The verified distributor data identifies the device as a surface-mount SOIC part, while the manufacturer datasheet result describes it as a low-voltage, single-supply dual SPST analog switch. Its primary role is connecting or disconnecting low-voltage analog signals rather than regulating power or driving high current. An analog switch is a semiconductor interface device that routes signals between circuit nodes under digital control. The SPST designation means each channel has a single-pole, single-throw arrangement, and 1:1 describes the signal-path configuration. As a dual analog switch, the ISL8325IB provides two switching sections that can be used for signal isolation, sample-and-hold paths, test-point routing, or other analog signal-routing systems. It belongs to the broader semiconductor hierarchy of analog switches, interface ICs, and signal-chain components. The verified data specifically confirms two circuits, SPST configuration, 60-ohm on resistance, and an 8-pin SOIC package. The data also identifies an industrial temperature grade from distributor listings. Other electrical characteristics, including supply-voltage limits, control thresholds, leakage current, channel capacitance, switching time, and absolute maximum ratings, are not included in the supplied sources and are marked for data confirmation rather than estimated. This conservative approach prevents unverified parameters from being presented as guaranteed design values. Typical use cases include low-voltage analog signal routing, measurement systems, communication interfaces, and test or control circuits where a digital control signal must select between analog paths. The SOIC-8 footprint is useful for conventional surface-mount PCB assembly. Because an analog switch can influence signal integrity, the input and output routing should be short and appropriately terminated, and control signals should be driven with compatible voltage levels. The 60-ohm resistance should be considered in the context of source impedance, load capacitance, bandwidth, and acceptable insertion loss. The ISL8325IB is appropriate when the design requires two SPST analog routes and can operate within the verified device limits. Its compact SOIC package and two-channel arrangement can simplify layouts compared with discrete switch implementations. The primary trade-off is that the verified data does not provide enough detail to guarantee off-state isolation, dynamic performance, or power-consumption targets without consulting the complete manufacturer datasheet. This page combines verified distributor identity, package information, datasheet availability, pricing-source links, and practical selection guidance. It also distinguishes confirmed facts from parameters that require engineering verification. Buyers should compare the complete datasheet, validate logic levels and signal amplitudes, and confirm lifecycle and qualification requirements before releasing a production design.
ISL83485IBZ-T - 3.3V 10Mbps RS-485/422 Transceiver, 8-SOIC | Renesas
The Renesas ISL83485IBZ-T is a 3.3V-powered, half-duplex, 10Mbps RS-485/RS-422 transceiver housed in an 8-pin SOIC package with a 1TX/1RX channel count and an integrated shutdown pin for low-power standby. It is built on a BiCMOS process that supports both the RS-485 differential multipoint standard and the RS-422 point-to-point standard, while delivering 10Mbps high-speed signaling for time-critical industrial links. Per the Renesas product page, this part is currently flagged as Last Time Buy, meaning new designs should plan for an alternative. A RS-485/RS-422 transceiver is a physical-layer (PHY) interface IC that converts the single-ended logic-level signals of a UART or microcontroller into the differential voltage swings required for balanced twisted-pair transmission. These transceivers are categorized under interface ICs and, more broadly, under wired-connectivity semiconductors, sitting beneath network controllers and above simple line drivers in the silicon hierarchy. They enable robust, noise-immune communication over long cable runs in electrically harsh environments. The key features of this part include a wide 3.0V to 3.6V supply range optimized for 3.3V logic systems, 1/8 unit-load receiver input impedance that allows up to 256 transceivers on a single bus, hot-plug circuitry that limits transient bus current during insertion, and a dedicated shutdown pin that drops quiescent current to microamp levels for power-sensitive applications. The 8-SOIC package supports a standard surface-mount footprint and is pin-compatible with industry-standard 3.3V RS-485 parts such as the MAX485 and SN75176B. The BiCMOS process combines bipolar drive strength on the bus side with CMOS low-power logic, achieving a balance of speed and quiescent consumption that pure-CMOS parts cannot match. With 10Mbps capability, the ISL83485IBZ-T fits high-speed sensor data links, while the part also survives ±15kV HBM ESD strikes per the datasheet, eliminating the need for external TVS protection in most field installations. Typical applications include industrial fieldbus networks, building automation gateways, security camera RS-485 control links, point-of-sale peripheral connections, and motor-drive feedback loops. In each of these scenarios, the ISL83485IBZ-T serves as the PHY layer between a UART-enabled host and the differential twisted-pair bus. When designing with this part, provision for a 120 ohm differential termination at each bus end and ensure the shutdown pin is tied high through a pull-up if unused, to avoid floating logic. A small 100nF decoupling capacitor placed within 5mm of the VCC pin is essential for hot-plug transient suppression. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer product page.
ISL8391IB - 4-Channel 35Ω SPST Analog Switch | Renesas
The Renesas Electronics ISL8391IB is a low-voltage, single- and dual-supply, quad SPST CMOS analog switch with four independent 1:1 circuits, 35 Ω on-resistance, and a 16-SOIC package. It accepts a single +2 V to +12 V supply or a dual ±2 V to ±6 V supply, making it suitable for low-voltage signal routing. The verified product data identifies low power consumption below 1 µW, leakage current up to 2.5 nA, and fast switching as key application characteristics. An analog switch is an electronically controlled interface that connects or disconnects an analog signal path. The SPST designation means each channel has one pole and one throw, while quad indicates four switching elements in one package. This device sits between sensors, amplifiers, data converters, test equipment, and other signal-chain circuits where a control signal must route a voltage without continuously conducting it. Its CMOS implementation supports low static power and high input impedance. Key features include four independent channels, 35 Ω on-resistance, low leakage, and operation from either single or dual supplies. The single-supply range is +2 V to +12 V, while the dual-supply range is ±2 V to ±6 V. These values allow use in battery-powered equipment and low-voltage instrumentation. The device is identified as a 16-SOIC, surface-mount interface IC. The four-channel architecture reduces the number of discrete switch components required in multiplexed or reconfigurable analog paths. Its low power consumption is useful when battery life is important, while low leakage helps preserve signal amplitude in high-impedance nodes. Fast switching makes the device relevant to measurement, control, and signal-routing systems, although exact switching-time limits and logic thresholds require confirmation from the manufacturer datasheet. Typical applications include battery-powered instrumentation, automated test equipment, data acquisition, sensor interfaces, audio and communications signal routing, and industrial control systems. The ISL8391IB is especially relevant when a designer needs four SPST paths in one 16-SOIC package and can operate the device from a low-voltage single or dual supply. Designers should verify the control-pin polarity, allowable analog signal range, absolute maximum ratings, and switching-time parameters against the manufacturer datasheet before layout. Keep routing short, provide a solid ground reference, and account for the 35 Ω on-resistance when designing source and load impedances. This page combines verified manufacturer-product information, distributor identification, package data, and practical selection guidance. It distinguishes documented values from parameters requiring verification and avoids presenting unreferenced electrical or timing specifications as established facts.
ISL8392IB - 4-Channel 35Ω SPST Analog Switch | Renesas
The Renesas Electronics ISL8392IB is a four-channel, 1:1 SPST CMOS analog switch with a typical on-resistance of 35 Ω, housed in a 16-SOIC package. It supports low-voltage single-supply operation from +2 V to +12 V or dual-supply operation from ±2 V to ±6 V. Four independent switches provide flexible signal routing for precision analog, measurement, test, and battery-powered equipment. An analog switch is a semiconductor-controlled pass element that connects or isolates circuit nodes under digital control. The ISL8392 family belongs to the interface IC hierarchy: analog switch → switch/multiplexer IC → interface integrated circuit. Its SPST configuration provides one conducting path per switch rather than a multi-channel multiplexer, making it useful when each signal requires independent routing. Verified device features include a maximum charge injection of 5 pC, on-resistance matching of 300 mΩ, and crosstalk of -89 dB at 1 MHz. The family data also identifies low power consumption of 1 µW, leakage current up to 2.5 nA, turn-on time of 60 ns, turn-off time of 30 ns, and maximum on-resistance flatness of 4 Ω. These characteristics suit signal paths where fast transitions, low leakage, and controlled charge injection are important. The switch architecture is designed for low-voltage precision routing rather than high-voltage power switching. Signal amplitude, supply range, input capacitance, control-logic levels, and switched leakage must all remain within device limits. Because ISL8392IB is listed as obsolete by GlobalSpec, new production designs should account for lifecycle risk and contact Renesas regarding supported sourcing before committing an active BOM. Typical uses include battery-powered sensor acquisition, multimeter and test-equipment input routing, sample-and-hold systems, data-acquisition modules, and low-power analog signal multiplexing. The 60 ns turn-on and 30 ns turn-off values can limit settling intervals, while 2.5 nA maximum leakage helps preserve weak-source measurements between switching events. Use the 16-SOIC footprint exactly as shown in the manufacturer pinout, and observe all control pins during unused channels. Do not infer the complete pin map or absolute maximum ratings from distributor snippets alone. Validate signal integrity, supply sequencing, and injected charge in the final analog channel because package parasitics and PCB capacitance can materially affect precision measurements. This page consolidates verified lifecycle, electrical, package, cross-reference, and sourcing information with engineering guidance that extends beyond a distributor listing. It also clearly separates confirmed data from parameters that still require datasheet or internal-inventory confirmation.
ISL84467IRTZ - Quad SPDT Analog Switch, 0.39Ω rON, 1.65-4.5V | Renesas
The Renesas (formerly Intersil) ISL84467IRTZ is an ultra-low ON-resistance, low-voltage, bidirectional Quad SPDT (Dual DPDT) analog switch housed in a 16-pin TQFN (3x3 mm) package. The device operates from a single +1.65V to +4.5V supply, delivers a typical ON resistance of 0.39Ω, and supports switching speeds of tON = 33ns and tOFF = 16ns. The 1.8V logic-compatible digital inputs allow direct interfacing with modern low-voltage microcontrollers without level shifters, making the part attractive for portable and battery-powered designs where both signal integrity and low quiescent drain matter. An analog switch (also called an analog multiplexer or bilateral switch) is a solid-state device that uses MOSFET transistors to route analog or digital signals between input and output pins under digital control. Quad SPDT (Single Pole Double Throw) means the device contains four independent 2:1 switches, each capable of selecting between two signal paths. Compared to electromechanical relays, analog switches offer far faster switching, no contact bounce, lower power, and indefinite mechanical life, but they have limited voltage handling and finite OFF isolation. Key features of the ISL84467IRTZ include 0.39Ω typical rON (which minimizes signal attenuation and distortion for low-level audio or precision analog signals), 1.8V logic-compatible inputs across the full supply range, break-before-make switching action to prevent momentary shorts between adjacent channels, and ESD protection on the logic and signal pins. The bidirectional signal path means each switch can carry signals in either direction with identical AC performance, simplifying PCB routing when source and destination roles are not predetermined. The four SPDT switches are organized as two DPDT (Double Pole Double Throw) pairs that switch in tandem, useful for differential signal routing in audio, USB, or data-acquisition front ends. The TQFN-16 package with an exposed pad provides low thermal resistance and a small 3x3 mm footprint, suitable for high-density handheld equipment. Targeted applications per the manufacturer datasheet include battery-powered portable instruments, audio/video signal routing, mobile handsets, and handheld test equipment. When designing with the ISL84467IRTZ, observe the absolute maximum signal voltage (typically equal to V+ plus ESD diode drops) and place decoupling capacitors close to the V+ pin. For low-distortion audio applications, the low rON and low charge injection of this switch help preserve signal fidelity; designers should still account for switch capacitance in bandwidth-limited paths. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet alone.
ISL8483IB - 250kbps Half-Duplex RS-485/RS-422 IC | Renesas
Renesas Electronics ISL8483IB is a 5 V, 250 kbps half-duplex RS-485/RS-422 transceiver with separate receiver and transmitter enables, low-power shutdown, and optional slew-rate-limited operation in an 8-pin SOIC package. The part is designed for industrial-grade, point-to-point and multidrop serial-interface systems requiring bidirectional data transfer over a balanced cable. An RS-485/RS-422 transceiver is an interface IC that converts between logic-level digital signals and differential bus voltages. RS-422 provides a driver-dominant, point-to-point signaling method, while RS-485 permits multiple drivers on a shared bus when only one node transmits at a time. The ISL8483IB combines one transmitter and one receiver in one package, supporting half-duplex communication over a common pair of differential conductors. Key features include a 250 kbps data rate, a 5 V supply, separate Rx and Tx enables, and a low-power shutdown function. The verified distributor description also identifies a slew-rate-limited configuration option. Slew-rate control reduces the edge speed of transmitted signals, limiting high-frequency harmonics and electromagnetic interference at the expense of maximum signaling rate compared with an unrestricted high-speed driver. The ISL8483IB uses separate active-high receiver-enable and driver-enable controls, allowing the host to place the unused side of the transceiver into a disabled state. Its bidirectional half-duplex arrangement is useful where two endpoints exchange requests and responses over a shared pair of wires. The device also supports transmitter shutdown for systems that need to reduce supply consumption when the bus is inactive. Typical applications include industrial serial interfaces, remote monitoring equipment, data acquisition modules, building-control systems, factory automation links, and RS-485-to-TTL conversion products. The 8-pin SOIC package supports conventional surface-mount assembly. The industrial temperature grade identified by the verified distributor listing makes the device suitable for equipment operating across an extended commercial temperature range, subject to the manufacturer's specified limits. Designers should verify the complete datasheet pinout, absolute maximum ratings, recommended external network, driver-load capability, and shutdown behavior before releasing a PCB. Cabling, termination, grounding, and transceiver-enable sequencing are as important as the nominal 250 kbps rating because unbalanced or incorrectly terminated buses can cause reflections, common-mode voltage errors, and unreliable communication. This page combines verified distributor information, structured drop-in-family alternatives, application guidance, and design notes in a format designed to accelerate component selection, replacement planning, and hardware implementation.
ISL8483IP - 5V RS-485/RS-422 Transceiver | Renesas
Renesas ISL8483IP is a single half-duplex RS-485/RS-422 transceiver operating from a 5 V supply, with selectable low-power high-speed or slew-rate-limited operation. The device combines one transmitter and one receiver in an 8-pin PDIP package and includes separate receiver and transmitter enables plus a low-power shutdown function. Verified distributor data identifies the ISL8483IP as a 250 kbps half-duplex RS-485/RS-422 transceiver with Rx/Tx enables and low-power SHDN. The package is specified as 8-DIP, or 8-PDIP, with a 0.300 inch, 7.62 mm body width. An RS-485/RS-422 transceiver is a balanced-interface interface IC used to connect a logic-level controller to a differential communication bus. RS-422 generally describes a point-to-point, balanced digital interface, while RS-485 supports multipoint bus arrangements and commonly uses transceivers that can disable their drivers when idle. The ISL8483IP belongs to the interface IC hierarchy and is intended for industrial-control, instrumentation, and embedded serial links requiring a 5 V supply and differential noise immunity. The verified data identifies a maximum signaling rate of 250 kbps and offers two operating approaches described as high speed or slew-rate limited. These modes are relevant when a design must balance communication rate against the transition rate of the differential driver. Additional control features named in the source material are the receiver enable, transmitter enable, and low-power shutdown input, allowing the host to manage bus direction and conserve power when communication is inactive. The ISL8483IP uses BiCMOS technology in the Intersil RS-485 and RS-422 product family. Although the provided search results describe the family as meeting both RS-485 and RS-422 standards, detailed limits for differential output voltage, receiver threshold, common-mode range, supply-current behavior, and isolation are not included in the supplied excerpts. Those parameters therefore require confirmation in the manufacturer datasheet before final circuit release. Typical applications include industrial sensor and actuator links, factory automation equipment, building-control systems, laboratory instrumentation, and embedded controllers communicating with remote RS-485 peripherals. The 250 kbps rate is appropriate for moderate-speed control and monitoring networks rather than high-bandwidth data transfer. In a multidrop bus, only one transmitter should normally be active at a time, while the receiver can monitor bus state when its driver is disabled. A key design consideration is the distinction between the PDIP and surface-mount ISL8483 package variants. Cross-reference results explicitly identify ISL8483EIBZ-T and ISL8483EIBZ-T7A as SOIC-8 surface-mount parts, so they are not drop-in replacements for an 8-PDIP board footprint. Before routing a replacement PCB, verify supply voltage, data rate, enable polarity, shutdown behavior, pinout, and transceiver-versus-receiver configuration against the manufacturer datasheet. This page consolidates the verified distributor descriptions, package distinctions, sourcing links, and practical replacement constraints into an engineering-focused view. It also identifies where the supplied evidence is incomplete, avoiding unsupported claims about pin assignments, electrical limits, lifecycle state, pricing, and thermal performance. Those fields should be completed from the authoritative manufacturer datasheet and current authorized distribution records.
ISL8484IU - Dual SPDT Low-Voltage Analog Switch | Renesas
Renesas Electronics ISL8484IU is a dual single-pole/double-throw analog switch with a single-supply operating range of +1.65 V to +4.5 V and an ultra-low on-resistance. The device contains two independent SPDT switch circuits in a 10-MSOP package and is designed for low-voltage, low-power signal-routing applications. Its stated on-resistance is 500 mOhm, while the available technical data also identifies 290 mOhm at a 4.3 V supply and 550 mOhm at a 1.8 V supply. An analog switch is an integrated interface circuit that routes electrical signals between terminals under digital control. A dual SPDT switch provides two selectable signal paths per switch section, making it useful for selecting one of two sources, routing a measurement signal, or supporting bidirectional communication. The ISL8484 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. The principal feature of the ISL8484IU is its low on-resistance across a low-voltage supply range. Available data lists on-resistance matching between channels as 0.06 Ohm and on-resistance flatness across the signal range as 0.03 Ohm. Power consumption is specified below 0.45 uW, while fast switching action is available when the supply is 4.3 V. These characteristics suit compact equipment operating from a single low-voltage rail. The device uses separate select and common terminals for each SPDT section. The 10-MSOP surface-mount package is offered in a 0.118-inch by 3.00 mm width format. The supplied data identifies the industrial temperature grade and 10 terminals. A publicly verified pin-number-to-pin-name diagram was not present in the supplied results, so the exact pinout is intentionally left unassigned rather than inferred from generic package conventions. Typical uses include low-voltage audio routing, sensor and measurement-signal selection, portable test equipment, communication-signal multiplexing, and compact industrial interfaces. For bidirectional signal paths, the control and common terminals must be operated within the voltage limits specified by the manufacturer datasheet. Care is required when switching powered signals because the exact overvoltage and break-before-make behavior should be confirmed from the current datasheet. A primary design consideration is the relationship between supply voltage and switch resistance. Lower supply operation provides less headroom for the internal switch and corresponds to higher resistance, while operation near 4.5 V provides the lower-resistance behavior listed in the available data. PCB layout should keep routing short and provide a stable return path, especially when the switch handles high-bandwidth or low-amplitude signals. This product page consolidates the verified manufacturer description, distributor inventory information, package details, switch characteristics, cross-reference findings, and practical engineering guidance. It also separates verified facts from unavailable values so designers can identify the target part quickly while recognizing which parameters still require confirmation in the current manufacturer datasheet.
ISL8485CB - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
The Renesas Electronics ISL8485CB is a 5V, low-power, high-speed RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package. It combines one driver and one receiver in a single integrated circuit for balanced industrial communication links, with a verified data rate of up to 5Mbps. The device operates from a single 5V supply and supports both high-speed and slew-rate-limited communication modes. Its 8-SOIC package is suitable for conventional surface-mount PCB assembly, while its half-duplex architecture allows one transceiver to share a bidirectional bus with controlled driver enable and receiver enable functions. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and receives differential signals back into CMOS-compatible logic levels. The ISL8485CB belongs to the transceiver hierarchy of interface ICs, where RS-422 provides a balanced point-to-point or multidrop communication format and RS-485 supports longer, noise-tolerant multipoint buses. The part is intended for systems that require compact, reliable differential signaling rather than a single-ended communications interface. The primary electrical attributes include a 5V supply, a 5Mbps data rate, one integrated driver, and one integrated receiver. The manufacturer family documentation identifies the ISL8485 as a CMOS 5V-powered RS-485/RS-422 transceiver family with low power consumption and both high-speed and slew-rate-limited configurations. The verified distributor description identifies the CB ordering code as an 8-SOIC, while the manufacturer document covers the related ISL8485, ISL8490, and ISL8491 family. Typical uses include industrial control systems, factory automation, instrumentation, building automation, and embedded equipment connected through a balanced bus. In a half-duplex network, the transceiver converts transmitted data into differential bus voltage and receives remote data when the driver is disabled. The 5Mbps capability supports high-rate factory communication, while slew-rate limiting can reduce reflected signaling on longer or less controlled cables. Designers should verify the complete pinout, enable polarity, driver and receiver disable behavior, termination requirements, and electrical limits against the Renesas datasheet before layout. RS-485 buses normally need termination at both physical ends, biasing to provide a defined idle state, and protection appropriate to the installation environment. The 8-SOIC package requires thermal and layout attention at elevated data rates or long-cable installations.
ISL8485CP - 5V RS-485/RS-422 Transceiver | Renesas
Renesas ISL8485CP is a 5 V, low-power, half-duplex RS-485 and RS-422 interface transceiver with one driver and one receiver, supplied in an 8-pin through-hole PDIP package. It is designed for balanced industrial communication links where a single transceiver must support both differential transmit and receive operation. The verified distributor data identifies the device as a 1/1 RS-422 and RS-485 transceiver in an 8-PDIP package. A transceiver combines a differential line driver and differential receiver into one interface component. In the transmit direction, the driver converts a logic-level signal into a balanced differential voltage across a twisted-pair bus; in the receive direction, the receiver converts the differential bus voltage back into a logic-level signal. RS-422 commonly supports point-to-point, balanced signaling, while RS-485 permits multiple drivers and receivers on a shared bus when the system implements the required addressing, biasing, and contention controls. The ISL8485CP family is identified as a low-power 5 V RS-485/RS-422 solution with options described by the manufacturer as high-speed or slew-rate-limited. This distinction is important when designing a bus: slew-rate control can reduce high-frequency ringing and electromagnetic interference, while a high-speed configuration can improve propagation delay. The exact speed, slew-rate, output-current, and receiver-threshold limits are not present in the supplied verified excerpts and must be confirmed in the manufacturer datasheet before final circuit design. The device is implemented in an 8-PDIP package for through-hole assembly rather than a compact surface-mount land pattern. This makes it suitable for industrial controllers, data-acquisition equipment, instrumentation, and legacy interface boards where DIP soldering, prototyping, or through-hole serviceability is preferred. The balanced interface also helps reject common-mode noise when the transmitter and receiver reference a common signal ground and the cable routing is controlled. Typical applications include factory-floor serial links, industrial control modules, remote sensor interfaces, laboratory equipment, and building automation equipment. Designers should confirm the device's exact drive strength, receiver thresholds, data rate, enable or shutdown behavior, and bus termination requirements from the full datasheet. They should also verify whether a fail-safe receiver, ESD rating, slew-rate selection, or automotive qualification is required for the target environment. This page combines verified distributor availability, package information, pricing data, source links, and replacement analysis with practical RS-485 design guidance. It deliberately distinguishes confirmed facts from parameters that still require datasheet verification, helping engineers evaluate the ISL8485CP without mistaking incomplete web snippets for complete technical specifications.
ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas
Renesas Electronics ISL8485IB is a single half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and a 5 V supply in an 8-pin SOIC package. The ISL8485IB uses BiCMOS technology and is specified for 4.5 V to 5.5 V power supplies, including the 10% supply tolerance identified on the Renesas product page. Its industrial temperature range extends from -40°C to +85°C. An RS-485/RS-422 transceiver is a differential communications interface IC that converts logic-level transmit and receive signals into balanced, noise-immune bus signals. The ISL8485 family supports both RS-485 half-duplex operation and RS-422 balanced operation. The ISL8485 configuration multiplexes its driver output and receiver input onto the same pair of bus terminals, allowing a compact eight-pin implementation. The principal features include a 5 Mbps maximum data rate, low-power BiCMOS construction, operation from a nominal 5 V rail, and a single-unit-load RS-485 bus interface. Half-duplex operation requires the design to control the driver-enable and receiver-enable functions so that the transmitter is disabled when the bus is not being driven. These characteristics make the device appropriate for industrial data links, instrumentation, factory equipment, and point-to-point or multidrop balanced communication. The ISL8485IB is one of three related devices: the ISL8485 provides half-duplex multiplexing, while the ISL8490 and ISL8491 provide separate receive and transmit paths for full-duplex applications. The Renesas ISL8485, ISL8490, and ISL8491 datasheet identifies these architectural differences explicitly. Because bus topology and enable logic affect protocol behavior, an existing PCB should be checked for pin functions before selecting a related family member. Typical installations include RS-485 industrial sensor networks, RS-422 controller-to-peripheral links, building-control equipment, and data-acquisition systems. The 5 Mbps capability supports faster communication than legacy low-speed RS-485 links, while the differential interface helps reject common-mode noise when the transceiver is used with correctly terminated cabling. Designers should verify the eight-pin pinout, supply decoupling, driver-enable sequencing, bus termination, and protection requirements against the manufacturer datasheet. Differential routing should use a controlled-impedance layout where practical, and the unused bus terminals must be handled according to the applicable RS-485 or RS-422 configuration. This page consolidates the verified Renesas and distributor information for the ISL8485IB, documents pin-compatible alternatives with their differences, and provides practical interface-design guidance that is not available from a distributor listing alone.
ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
The Renesas ISL8485IP is a 5V, low-power, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5Mbps and supplied in an 8-pin DIP package. It provides one balanced transceiver interface for bidirectional multipoint data communication, places one unit load on an RS-485 bus, and operates from a supply range of 4.5V to 5.5V. The device is intended for industrial communication links requiring either high-speed operation or controlled slew rates. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential signals for balanced wired communication and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced links, while RS-485 permits multipoint buses and driver-enable control. The ISL8485IP belongs to the transceiver hierarchy within interface ICs and combines transmitter, receiver, bus-enable control, and protection functions in one package. Key features include a 5Mbps maximum data rate, 4.5V to 5.5V supply tolerance, one-unit-load bus loading, and support for both RS-485 and RS-422 signaling. The 8-pin DIP package is suitable for conventional through-hole assembly, prototyping, repair, and industrial control equipment. Its half-duplex arrangement allows the same differential pair to transmit and receive, although external direction-control logic is normally required. The BiCMOS architecture combines bipolar and CMOS characteristics to provide low-power operation with high data-rate capability. According to the Renesas ISL8485 family information, the ISL8485, ISL8490, and ISL8491 devices are 5V-powered single transceivers that meet RS-485 and RS-422 standards. The family supports supply voltages with 10% tolerance and presents one unit load to the RS-485 bus, helping control loading when multiple nodes share a communication line. Typical applications include industrial factory automation, programmable-logic-controller communication, building-control networks, instrumentation links, and embedded serial-interface equipment. In these systems, the transceiver serves as the physical-layer interface between a controller UART or logic port and a balanced RS-485 or RS-422 cable. Its 5Mbps capability supports high-speed equipment links, while slew-rate-controlled variants in the broader family can be useful where lower EMI is the priority. PCB design should preserve the differential signal path and provide controlled termination and biasing appropriate to the selected RS-485 or RS-422 topology. Keep the transceiver close to the connector, route the differential pair as a coupled pair, and place termination components where they can be configured for the intended network. The maximum 5.5V supply is especially important in industrial systems because transients and supply tolerances must remain within the device rating. This product page combines verified distributor identification, package and interface details, family-level electrical characteristics, alternative sourcing information, and application-specific engineering guidance. It also distinguishes explicitly verified facts from parameters that require confirmation from the manufacturer datasheet before schematic release or production qualification.
ISL8487IB - 250 kbps RS-485/422 Transceiver | Renesas
The Renesas Electronics ISL8487IB is a 5 V, single-channel half-duplex RS-485/RS-422 interface transceiver with a 250 kbps data rate, 1/4 unit load, and an 8-pin SOIC package. It combines one driver and one receiver in a fractional-unit-load design intended for balanced industrial communication links where the number of connected nodes is important. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into digital logic. Positioned within the hierarchy of transceiver, communication interface, interface IC, and semiconductor categories, the ISL8487IB supports RS-485 and RS-422 networks while presenting a lower bus loading than a one-unit-load device. The ISL8487IB operates from a 5 V supply and presents a 1/4 unit load, allowing up to 128 transceivers on a compliant RS-485 bus. Its maximum data rate is 250 kbps, and the listed receiver hysteresis is 70 mV. The 8-SOIC surface-mount package measures approximately 0.154 inches, or 3.90 mm, in width and supports conventional board-assembly and inspection processes. Because the device is a half-duplex transceiver, the receiver and driver share the bus path and direction is controlled by the DE and RE inputs. This architecture suits point-to-point links as well as multidrop buses in which multiple nodes may communicate under a token-passing or polled protocol. The fractional unit load reduces input impedance loading compared with a standard one-unit-load transceiver, improving scalability without requiring an alternative physical bus topology. Typical applications include industrial process monitoring, factory automation, remote meter reading, building controls, instrumentation, and general-purpose RS-485 or RS-422 links. The 250 kbps rate is suitable for supervisory communications and moderate-speed data transfer, while the 1/4 unit load is especially useful when several nodes must share the same twisted-pair bus. Because the transceiver is not galvanically isolated, applications with large ground-potential differences may require an external isolation strategy. Designers should verify termination, biasing, differential routing, and protection against the electrical environment of the cable. The differential pair should be routed as a controlled-impedance pair where practical, and the transceiver should be placed close to the connector to minimize unprotected trace exposure. Supply decoupling and grounding must follow the manufacturer datasheet recommendations. This page combines verified distributor specifications, lifecycle information, source-linked pricing, package details, application guidance, and defensible same-footprint alternatives. It also distinguishes confirmed data from parameters not present in the supplied source material, helping engineers evaluate the obsolete ISL8487IB without assuming unverified electrical characteristics.
ISL8487IP - 5V Half-Duplex RS-485/RS-422 Transceiver | Renesas
Renesas ISL8487IP is a 5 V, half-duplex RS-485/RS-422 interface transceiver with one transmitter and one receiver in an 8-pin PDIP package. It supports a 1/8-unit-load receiver characteristic, low-power operation, driver-enable and receiver-enable control, and a low-power shutdown function. These characteristics make it suitable for bidirectional serial-data links that require both RS-485 and RS-422-compatible signaling without a separate supply rail for the interface. An RS-485/RS-422 transceiver is a differential interface IC that converts logic-level data into balanced differential signals and converts incoming differential signals back into receiver-compatible logic. Within the broader hierarchy, it is a transceiver interface IC, a wired-communication interface, and part of the broader semiconductor and industrial-control ecosystem. Its half-duplex architecture allows a pair of devices to share the same differential pair, although only one transmitter should drive the bus at a time. The ISL8487IP provides a 1/8-unit-load receiver, allowing multiple nodes to share a bus more effectively than a one-unit-load receiver. Its 5 V supply, low-power shutdown, separate transmitter and receiver enables, and selectable high-speed or slew-rate-limited operation give the designer several ways to balance throughput, EMI control, and power consumption. The transmitter-enable and receiver-enable inputs also support orderly bus-direction control in half-duplex equipment. According to the manufacturer datasheet, the device uses fractional-unit-load BiCMOS transceiver technology intended for balanced RS-485 and RS-422 networks. The slew-rate-limit option reduces the rate of change on driver output edges, which can help control high-frequency ringing and electromagnetic emissions. Conversely, the high-speed mode is intended for links where maximum communication rate is more important than edge-rate control. Exact propagation-delay, data-rate, differential-output, and current-limit values were not present in the supplied web data. Typical uses include industrial equipment links, building-control interfaces, instrumentation buses, data-acquisition systems, and host-controller communication ports. In a half-duplex system, the transceiver can connect a controller to a multidrop field bus while logic-controlled enables determine whether the node transmits or receives. The low-power shutdown function is useful when a connected module must reduce current consumption while preserving a stable local bus connection. Designers should verify the exact recommended termination, biasing, common-mode range, and decoupling requirements in the manufacturer datasheet before release. Differential pairs should be routed with continuous references and matched spacing, while a slew-rate-limited mode may be preferable in cables or cabinets exposed to significant EMI. The 8-pin PDIP package also requires adequate spacing around the leads for soldering and inspection.
ISL8488IB - 250kbps Full-Duplex RS-485/422 | Renesas
Renesas Electronics ISL8488IB is a 5V, full-duplex RS-485 and RS-422 transceiver capable of operation at 250kbps in an 8-pin SOIC package. The integrated interface IC combines one transmitter and one receiver for bidirectional point-to-point or multipoint serial links, while its slew-rate-limited driver helps reduce electromagnetic interference and ringing on inadequately terminated lines. An RS-485 transceiver is a differential communications interface IC used to connect a controller, programmable logic controller, sensor, or industrial endpoint to a balanced serial bus. RS-485 is a physical-layer standard suited to noisy industrial environments and longer cable runs, while RS-422 provides compatible differential signaling for point-to-point links. The ISL8488IB occupies the interface-IC hierarchy alongside RS-232 transceivers, isolated transceivers, and CAN controllers, but it operates with differential RS-485/RS-422 signaling rather than single-ended RS-232. The verified device data identifies a 5V supply, a 250kbps maximum signaling rate, full-duplex operation, slew-rate-limited drive, low-power operation, and the absence of separate receiver-enable and transmitter-enable controls. These features make the device appropriate for industrial and commercial systems where a compact, always-enabled full-duplex interface is preferred. The 8-SOIC format also supports conventional surface-mount PCB assembly and broad availability through distributors. The full-duplex arrangement separates the differential driver and receiver paths, allowing simultaneous transmission and reception. The slew-rate-limited driver is particularly useful where long cables, branch stubs, imperfect terminations, or reflected signals could otherwise produce unwanted EMI or excessive edge ringing. The supplied search evidence does not provide a verified common-mode range, receiver sensitivity, fail-safe behavior, bus loading, or propagation-delay distribution, so those values should be confirmed from the complete manufacturer datasheet before release. Typical uses include industrial controller links, factory automation equipment, building-control systems, instrumentation, telecom equipment, and embedded serial links where RS-485 or RS-422 is already selected. Because the part has no separate RX/TX enable inputs, the attached controller must handle bus-direction control elsewhere or the transceiver must remain in its continuously enabled interface configuration. The 250kbps data rate also places the device below the throughput normally associated with modern high-speed CAN or differential Ethernet interfaces. For a new PCB, preserve the manufacturer-recommended bypass capacitance, connect the differential pair as a controlled impedance or tightly matched pair, and provide termination only where the cable topology requires it. Avoid placing long unprotected stubs on the bus. Designers should also verify ground potential differences between connected systems because RS-485 relies on the common-mode voltage remaining within the device's supported operating range. This product record combines verified distributor listings, the manufacturer-family datasheet, available cross-reference evidence, packaging details, interface-use guidance, and a conservative same-footprint replacement assessment. It also distinguishes confirmed specifications from unavailable parameters so procurement and engineering teams can identify which values still require confirmation from the full datasheet.
ISL8488IP - 250kbps Full-Duplex RS-485/RS-422 | Renesas
The Renesas Electronics ISL8488IP is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver operating at up to 250 kbps, supplied in an 8-pin plastic DIP package. The device is designed for bidirectional industrial data links and combines a transmitter, receiver, and bus-driver/receiver functions without separate receive or transmit enable pins. Its slew-rate-limited operation helps reduce unwanted high-frequency signal content on longer RS-485 networks. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential bus voltages and converts received differential bus signals back into CMOS-compatible logic. In the broader electronics hierarchy, it is an interface IC within the transceiver family, designed for reliable point-to-point or multipoint communication over cables and industrial backplanes. The ISL8488IP supports both RS-485 and RS-422 system requirements while operating from a single 5 V supply. Key verified characteristics include a 250 kbps maximum signaling rate, full-duplex operation, 5 V supply operation, integrated RS-485/RS-422 transceiver functionality, and slew-rate-limited signaling. The absence of dedicated transmit and receive enable inputs is useful in applications where the interface direction is fixed or managed elsewhere. Its low-power design is intended for embedded industrial, communications, instrumentation, and control systems where reduced energy use and controlled edge rates are important. The device combines differential bus outputs with a receive path designed for data-link applications. Because the ISL8488IP is slew-rate limited, engineers should evaluate its 250 kbps rating against protocol timing, cable length, termination requirements, and the waveform behavior of the connected system. The 8-PDIP package favors through-hole construction, thermal management through the printed-circuit board, and applications that favor a conventional DIP footprint over a surface-mount package. Typical uses include industrial controller links, remote instrumentation, point-to-point communications equipment, factory data acquisition, and embedded systems exchanging commands between a controller and a remote peripheral. Full-duplex operation can simplify systems that continuously require independent transmit and receive paths. The lack of separate enable pins also reduces external control logic, although it may not suit designs that require direction switching or controlled bus tri-state behavior. For a new layout, place the transceiver near the connector and bus entry, route the differential pair as a tightly coupled pair, apply the appropriate termination and protection network, and maintain a continuous ground reference where required by the communication standard. Check the manufacturer datasheet for exact receiver thresholds, driver limits, supply-current values, temperature limits, and absolute maximum ratings before releasing production hardware. This page combines the verified 250 kbps, 5 V, full-duplex, RS-485/RS-422, slew-limited, 8-PDIP, and no-enable characteristics with practical integration guidance. It also distinguishes verified facts from unavailable datasheet details so procurement and engineering teams can identify what must be checked in the full manufacturer documentation.
ISL8489IB - 250kbps RS-485/422 Transceiver | Renesas
The Renesas Electronics ISL8489IB is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver capable of operation at 250 kbps, packaged in a 14-pin SOIC. It combines one driver and one receiver in a single integrated circuit and provides both high-speed and slew-rate-limited operation. The device does not include separate receiver-enable or transmitter-enable controls, making it suitable for continuously enabled balanced communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and converts received differential signals back into logic levels. These balanced interfaces belong to the broader wired-communication hierarchy and are commonly used where noise immunity, signal integrity, and reliable communication over longer cables are more important than single-ended signaling. The verified product information identifies a 5 V supply, low power consumption, full-duplex operation, support for both RS-485 and RS-422, and data rates up to 250 kbps. Its 14-pin SOIC package supports conventional surface-mount PCB assembly. Because the device lacks separate RX and TX enable pins, it is particularly appropriate for designs that keep both directions of the balanced interface continuously active. The ISL8489 family is described by the manufacturer as a BiCMOS 5 V single-transceiver solution designed for RS-485 and RS-422 balanced communication. Its low-power architecture supports equipment in which multiple interface channels may be present. High-speed or slew-rate-limited operation gives designers a choice according to cable length, topology, and signal-integrity requirements, although exact edge-rate and propagation-delay limits must be confirmed in the manufacturer datasheet. Typical uses include industrial automation links, building-automation equipment, instrumentation, motor-control systems, and industrial data networks. The device can also support point-to-point balanced links where continuous full-duplex operation is preferred. Companion interface devices such as the SN65HVD06D, SP485ECN-L, and SN75174DWR may be relevant when designing connected RS-485 networks or comparing transceiver families. A key design consideration is the absence of independent transmit and receive enables. PCB designers should therefore account for continuous driver activity and verify the driver state, bus termination, protection strategy, and cable topology against the system operating requirements. Decoupling, grounding, and differential-routing practices remain essential for reliable operation on externally accessible industrial buses. This page consolidates verified distributor listings, exact interface and packaging information, sourcing data, comparison fields, and practical design guidance. Where detailed electrical limits or a verified pin mapping were not present in the supplied source data, the missing information is explicitly identified rather than estimated.
ISL8489IP - 5V 250kbps Full-Duplex RS-485/422 | Renesas
Renesas Electronics ISL8489IP is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver capable of operation at 250 kbps and packaged in a 14-pin PDIP. The device combines one driver and one receiver in a single package, supports balanced differential communications, and provides a slew-rate-limited alternative for systems that require reduced signal-edge velocity. Its operating characteristics are suited to industrial, instrumentation, communications, and embedded data-acquisition equipment that must connect a host or controller to a balanced bus. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and converts received differential signals back into logic levels. RS-485 supports multipoint bus communication over long cable runs, while RS-422 commonly supports point-to-point and one-driver topologies. A full-duplex transceiver provides separate paths for transmitting and receiving, unlike half-duplex designs that share a bus and require direction-control logic. The ISL8489IP therefore fits designs that need simultaneous bidirectional communication without sharing a physical signal pair. Key verified features include a 5 V supply requirement, a maximum signaling rate of 250 kbps, full-duplex operation, support for both RS-485 and RS-422, low-power operation, and a slew-rate-limited operating option. The 14-pin PDIP package also provides through-hole compatibility for equipment requiring sockets, prototyping, or manually assembled industrial control boards. The indexed descriptions do not specify separate receiver-enable or transmitter-enable controls, indicating that this version is intended for continuous full-duplex operation. The transceiver architecture provides differential signaling, which is valuable in environments containing industrial machinery, switching supplies, and long interconnects. Differential voltage is measured between the two conductors of a pair rather than relative to ground, improving noise immunity on the receive side. The 250 kbps rate is appropriate for low-to-moderate-speed control and monitoring links where higher signaling rates are unnecessary. The slew-rate-limited behavior can help reduce edge-related ringing and electromagnetic interference when implemented with a correctly terminated network. Typical applications include industrial sensor and actuator networks, factory equipment links, building-control interfaces, laboratory instrumentation, point-to-point data links, and RS-422-compatible control systems. In these systems, the transceiver can connect a UART or microcontroller serial port to a balanced bus. Designers should still verify cable length, topology, grounding, termination, and logic-level compatibility against the complete system requirements before production release. A key design consideration is that the 14-pin PDIP package is not as compact as a surface-mount transceiver. It nevertheless simplifies through-hole construction and socket-based maintenance. The principal engineering trade-off is between 250 kbps operation, low power, full-duplex behavior, and the practical size and assembly requirements of a 14-pin through-hole package. This page consolidates the verified distributor and manufacturer-datasheet indexing information for the ISL8489IP with product-specific engineering guidance, specification gaps, and a transparent replacement assessment. It does not infer unseen electrical limits or substitute candidates whose pin compatibility has not been demonstrated.
ISL8490IB - 5V Low-Power RS-485/RS-422 Transceiver | Renesas
Renesas ISL8490IB is a 5V, low-power RS-485/RS-422 interface transceiver packaged in an 8-pin SOIC. It is designed for balanced serial data links that require the physical signaling characteristics of both RS-485 and RS-422 interfaces. The verified source material identifies the ISL8490 as a single transceiver supporting high-speed operation or slew-rate-limited operation, allowing it to suit point-to-point RS-422 links as well as multipoint RS-485 networks when used with appropriate bus termination and biasing. Its interface role places it within the transceiver and line-driver hierarchy of communication interface ICs. An RS-485 transceiver converts logic-level digital information into differential signals suitable for balanced industrial communication cables. Differential signaling provides resistance to common-mode noise and allows communication over longer cable runs than a single-ended interface. An RS-422 transceiver similarly uses differential signaling, normally in a point-to-point topology. The ISL8490IB therefore serves as an interface between a digital controller or host and physical copper wiring while placing the high-voltage, high-current bus activity on the transceiver side of the circuit. The principal verified feature is its 5V supply operation. This places it among low-voltage CMOS interface devices intended for systems with compatible digital logic rails. The part is described as low power and as supporting either high-speed or slew-rate-limited communication. High-speed operation prioritizes data throughput, while slew-rate limiting reduces transition-edge energy and can help control electromagnetic interference and ringing on slower networks. Exact data-rate, supply-current, differential-output, input-threshold, and temperature-range values must be confirmed in the manufacturer datasheet before a design is released. Typical uses include industrial RS-485 links, point-to-point RS-422 interconnects, instrumentation, factory automation, building controls, and embedded communication networks. In each case, the transceiver is placed between the controller UART or logic interface and the A/B differential pair. Appropriate cable routing, common-mode grounding, surge protection, termination, and fail-safe biasing remain important parts of the complete interface. Designers should preserve the exact pin mapping and verify the required driver-enable, receiver-enable, termination, and exposed-pad details against the ISL8490 manufacturer datasheet. This page consolidates verified product identity, package information, source links, application guidance, and engineering considerations that are not presented together on a basic distributor listing.
ISL8490IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
The Renesas Electronics ISL8490IP is a 5 V, low-power, full-duplex RS-485 and RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and an 8-pin PDIP package. The device supports both high-speed RS-485 communication and RS-422 point-to-point links, while its separate receiver and driver enable paths provide flexibility for half-duplex control through the DE and RE inputs. Its operating-temperature range is -40°C to +85°C, making it suitable for industrial and commercial equipment requiring a through-hole interface solution. A transceiver is an interface IC that converts digital logic signals into balanced differential signals for reliable communication over noisy or long cable runs. In the hierarchy, the ISL8490IP is a line transceiver, a type of interface IC and communications semiconductor. RS-485 supports multiple drivers and receivers on a shared bus, whereas RS-422 commonly uses a dedicated driver and receiver for point-to-point or multidrop networks. This transceiver supports both protocols and therefore provides a useful interface between CMOS/TTL logic and balanced cabling. The verified headline specifications are a 5 V supply, 5 Mbps maximum data rate, 70 mV receiver hysteresis, 1 driver, 1 receiver, full-duplex operation, and support for RS-422 and RS-485. These parameters place the part in the low-power, high-speed or slew-rate-limited transceiver category described by the manufacturer documentation. The 8-pin PDIP format also permits conventional through-hole PCB assembly rather than requiring a fine-pitch surface-mount land pattern. Technically, the balanced driver and receiver provide noise immunity over longer interconnects than ordinary single-ended logic. Receiver hysteresis helps distinguish signaling states in the presence of noise, while the 5 Mbps capability supports communication rates beyond the slow speeds commonly used by legacy RS-485 systems. Because the exact input capacitance, output timing, supply-current limits, and slew-rate settings are not included in the supplied verified excerpts, design engineers should confirm them in the manufacturer datasheet before finalizing timing, termination, and decoupling. Typical uses include industrial controllers, building automation equipment, data acquisition systems, instrumentation, industrial networking equipment, and embedded control links. For an RS-485 bus, the circuit requires suitable line termination and biasing. For RS-422, driver and receiver connections should follow the source and destination topology specified by the system architecture rather than being treated as a multi-drop RS-485 bus. The principal design consideration is signal integrity at 5 Mbps. Layout should minimize the distance between the transceiver, protection devices, connector, and differential pair, while keeping the two conductors of each balanced pair closely coupled. Decoupling close to the supply pin, controlled ground return paths, and appropriate surge protection help maintain reliable operation in industrial environments. This page consolidates the verified distributor and manufacturer-document information with lifecycle status, procurement guidance, application fit, package details, and honest replacement limitations. It distinguishes confirmed facts from specifications that still require verification from the full Renesas datasheet.
ISL8491IB - 5V RS-485/RS-422 Transceiver | Renesas
Renesas Electronics ISL8491IB is a 5V, low-power, full-duplex RS-485/RS-422 transceiver integrated circuit in a 14-pin SOIC package. It combines one driver and one receiver in a single balanced-communications device, providing the core physical-layer functions required for point-to-point RS-422 links and multipoint RS-485 buses. The verified manufacturer and distributor records identify the device as a 14-SOIC, full-duplex RS-485/RS-422 transceiver with high-speed or slew-rate-limited operation. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and reconstructs logic-level data from those differential signals. The differential signaling belongs to the transceiver class within interface ICs, data communications, and the broader semiconductor hierarchy. Balanced operation improves noise immunity by deriving the received state from the voltage difference between two conductors rather than relying on a signal measured relative to ground alone. The principal identified features of the ISL8491IB are its 5V CMOS-style supply operation, low-power architecture, full-duplex configuration, and support for both RS-485 and RS-422 communication standards. Because it contains one transmitter and one receiver, the part can support simultaneous transmit and receive paths when the host or controller provides separate request and data-bus signals. The verified distributor description also identifies variants capable of high-speed or slew-rate-limited operation, allowing engineers to compare communication behavior and system timing requirements. The ISL8491IB is suitable for industrial data links, industrial automation equipment, instrumentation, building-control networks, and embedded systems that exchange data over balanced copper cabling. Its 14-pin SOIC package supports conventional surface-mount PCB assembly, while the full-duplex arrangement avoids sharing one physical pair between opposing directions. Designers must still provide suitable logic interfacing, termination, biasing, grounding, and protection appropriate to the cable length, data rate, and industrial environment. A critical design consideration is that the transceiver's communication mode and electrical settings must match the network topology. RS-422 generally supports a point-to-point driver relationship, while RS-485 permits multiple drivers on a bus but requires careful idle-state biasing and termination. The exact driver strength, receiver thresholds, data rate, common-mode range, ESD rating, and pin-level truth table are not supplied in the verified data and should be confirmed in the manufacturer datasheet before layout or production use. This page consolidates the verified distributor and manufacturer references for the ISL8491IB, distinguishes the device from general-purpose interface ICs, and provides sourcing, selection, replacement, and application guidance. It also records uncertain specifications explicitly rather than substituting estimates, helping engineers make an informed first-stage decision before validating the complete electrical limits and pin configuration.
ISL8491IP - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
The Renesas Electronics ISL8491IP is a 5 V, low-power RS-485/RS-422 line transceiver with one driver and one receiver, full-duplex operation, a maximum data rate of 5 Mbps, and a 14-pin PDIP package. The device combines differential RS-485 and RS-422 communication support in a single integrated circuit, making it suitable for industrial data links, instrumentation, and point-to-point balanced communication systems. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential balanced signals for reliable data transmission over cables. These differential signaling methods are members of the broader interface-controller category, connect digital systems to physical communication links, and provide improved noise immunity compared with single-ended logic interconnects. The ISL8491IP supports both protocols, allowing equipment designers to select the appropriate termination and biasing arrangement for the cable and system topology. The verified part data identifies a 4.5 V to 5.5 V supply range, 5 Mbps maximum data rate, 70 mV receiver hysteresis, one transmitter, one receiver, full duplex, and an operating temperature range of -40°C to 85°C. These characteristics suit industrial equipment operating near a regulated 5 V rail and requiring communication speeds up to 5 Mbps. The through-hole PDIP-14 package is also appropriate for leaded PCB designs where a small surface-mount land pattern is not required. The ISL8491IP is listed as obsolete in the verified source data. Consequently, engineers should not assume that new production procurement is available and should confirm lifecycle status, traceability, and last-time-buy opportunities directly with the manufacturer or an authorized distributor. Renesas Electronics Corporation is the listed supplier, while the original documentation is associated with Intersil Corporation. Typical uses include industrial control links, factory automation equipment, remote sensor interfaces, RS-422 point-to-point links, and test-and-measurement systems. In these applications, the device separates the logic domain from the noisy cable environment through differential transmission and reception. Cable length, data rate, termination, common-mode range, and grounding remain system-level constraints that must be evaluated separately from the integrated circuit specifications. A practical design step is to preserve the transmitter enable and receiver enable control paths, place termination only where required by the cable topology, and provide a stable 5 V supply close to the device. Since the verified sources do not provide a complete pin table, absolute maximum ratings, output current, or detailed electrical characteristics, those values should be confirmed in the manufacturer datasheet before final release. This page combines verified distributor and datasheet information with lifecycle, sourcing, application, and design guidance. It also distinguishes verified facts from parameters that still require manufacturer-document confirmation, helping engineers evaluate the ISL8491IP without confusing an obsolete status with an interchangeable modern replacement.
ISL8499IR - 0.24 Ohm Low-Voltage Quad SPDT Switch | Renesas
The Renesas Electronics ISL8499IR is a low-voltage, bidirectional, quad SPDT analog switch housed in a 16-pin QFN package. It operates from a single +1.65 V to +4.5 V supply, with an on-resistance of 0.24 ohm at +4.3 V, 0.26 ohm at +3.0 V, and 0.45 ohm at +1.8 V. Switching times are 15 ns for tON and 13 ns for tOFF, making the device suitable for battery-powered equipment requiring low resistance and rapid signal selection. An analog switch is an integrated semiconductor that routes analog signals between external nodes under digital control. The ISL8499 contains two independent dual-pole, double-throw switching functions, commonly described as a quad SPDT or dual DPDT device. Within the interface IC and analog-switch hierarchy, its low-voltage operation, bidirectional signal path, and low power consumption are particularly useful for portable audio, test, communication, and battery-operated measurement systems. The principal electrical features include a +1.65 V to +4.5 V single-supply range, low on-resistance across multiple supply voltages, and on-resistance matching between channels of 0.04 ohm. The verified datasheet information also reports on-resistance flatness across the signal range of 0.05 ohm. These characteristics help reduce insertion loss and channel-to-channel resistance variation when routing sensitive analog signals. The device is designed for 1.8 V-compatible logic when operated from a +3 V supply. With a +4.2 V supply and 2.85 V logic-high inputs, the maximum supply current is 10 microamperes. Power dissipation is reported below 0.2 microwatts under the stated low-power conditions, supporting the use of the ISL8499IR in battery-powered equipment where leakage and standby consumption can affect the usable runtime. Typical applications include routing audio signals in portable equipment, selecting sensor inputs in test and measurement systems, multiplexing communication channels, and switching low-voltage analog signals in battery-operated instruments. The 15 ns tON and 13 ns tOFF characteristics support fast system reconfiguration, while the low on-resistance limits signal attenuation across the selected channel. Designers should verify control-logic levels against the selected supply voltage and ensure that switched signals remain within the device's supported analog-signal range. The exposed thermal pad and exposed-pad construction also require a suitable PCB land pattern and adequate copper for heat spreading, particularly when continuously routing signals at higher frequencies or temperatures. This page consolidates the verified Renesas product information, source-linked pricing and lifecycle references, explicitly identified drop-in relationships, and practical selection guidance. It also separates documented performance from parameters that still require confirmation from the complete manufacturer datasheet or a specific distributor record.