Produk (22.000+)

ATXMEGA128A3-AU - 32MHz 128KB AVR MCU | Microchip
ATXMEGA128A3-AU

ATXMEGA128A3-AU - 32MHz 128KB AVR MCU | Microchip

The Microchip Technology ATXMEGA128A3-AU is a low-power, high-performance 8/16-bit AVR XMEGA A3 microcontroller operating at up to 32 MHz, with 128 KB of self-programming Flash memory, 8 KB of SRAM, and 2 KB of EEPROM in a 64-pin TQFP package measuring 14 x 14 mm. The device provides up to 32 MIPS throughput and combines a 4-channel DMA controller with an 8-channel event system for efficient peripheral transfers and deterministic event handling. An 8/16-bit microcontroller is a semiconductor controller designed to execute embedded instructions with low power consumption and broad peripheral integration. The AVR enhanced RISC architecture supports single-cycle instruction execution, while the XMEGA A3 family integrates memory, communications, timing, analog, and event-management resources into one device. Within the product hierarchy, the ATXMEGA128A3-AU belongs to the XMEGA family of 8/16-bit MCUs and the broader embedded microcontroller and semiconductor categories. Key features include 128 KB of in-system self-programmable Flash, an 8 KB boot-code section with independent lock bits, 8 KB of SRAM, and 2 KB of EEPROM. The four-channel DMA controller moves data without occupying the CPU for each transfer, while the eight-channel event system links timers, comparator outputs, and other peripherals. Operation from 1.6 V to 3.6 V supports low-voltage embedded systems, and the 32 MHz maximum clock provides a strong balance between compute throughput and flexible power management. The architecture is designed to improve peripheral efficiency rather than relying only on interrupt-driven CPU servicing. DMA can transfer data among SRAM, Flash, EEPROM, and compatible peripherals, while the event system can route peripheral events directly to other peripherals. These features are particularly useful in designs that combine communication, control, data acquisition, and real-time timing without requiring a much larger processor. The manufacturer describes the family as supporting industrial, building automation, motor control, climate control, networking, metering, handheld, medical, and appliance applications. Typical uses include industrial controllers, building and HVAC equipment, factory automation nodes, motor-control modules, power tools, metering equipment, optical instruments, and medical or handheld products. The ATXMEGA128A3-AU is most appropriate when firmware needs substantial local memory, flexible event routing, and deterministic DMA transfers in a compact surface-mount package. Its integrated resources can also reduce the number of external devices required around an embedded control board. PCB design should preserve clean power and ground distribution around the 64-pin TQFP footprint, place decoupling capacitors close to the supply pins, and follow the manufacturer's pin and layout guidance for high-speed signals. Firmware developers should also account for boot-section protection, fuse settings, peripheral event routing, and DMA channel arbitration before finalizing the system architecture. This page combines the manufacturer's device architecture and memory details with package-specific selection guidance, verified alternative references, application fit, and practical design considerations for engineers evaluating the ATXMEGA128A3-AU as an embedded-control platform.

Permintaan RFG Kontak
ATXMEGA128A4U-AUR - 8/16-bit AVR XMEGA MCU, 128KB Flash, 44-TQFP | Microchip
ATXMEGA128A4U-AUR

ATXMEGA128A4U-AUR - 8/16-bit AVR XMEGA MCU, 128KB Flash, 44-TQFP | Microchip

The Microchip ATXMEGA128A4U-AUR is an 8/16-bit AVR XMEGA A4U microcontroller featuring 128 KB of in-system self-programmable Flash, 8 KB SRAM, 2 KB EEPROM, and a 4 KB boot code section, all packaged in a 44-pin TQFP (10x10 mm) supplied on tape and reel. It operates at up to 32 MHz delivering up to 32 MIPS throughput, integrates a 4-channel DMA controller, an 8-channel event system, and a full-speed USB 2.0 device/host interface that distinguishes the A4U family from earlier A4 devices. The part number suffix "-AUR" indicates the industrial temperature grade and tape-and-reel packaging for high-volume assembly. An AVR XMEGA microcontroller is a high-performance 8/16-bit RISC MCU family from Microchip (originally Atmel) targeting low-power embedded designs that need more peripherals than classic ATmega parts but still rely on the AVR core rather than ARM Cortex-M. Within the broader taxonomy it sits as an MCU -> microcontroller -> embedded controller -> semiconductor. The "XMEGA" name signals an upgraded peripheral set including hardware crypto, DES, AES, and 12-bit ADC/DAC blocks, plus the unified event system for inter-peripheral signalling without CPU intervention. Key differentiating specifications include the 128 KB Flash (64K x 16 organization), 8 KB SRAM, 2 KB EEPROM, 12-bit ADC and DAC peripherals, full-speed USB 2.0 with device and host capability, and an operating voltage range of 1.6 V to 3.6 V. The device supports both 1.8 V and 2.5 V/3.3 V operation, allowing direct attachment to Li-ion, NiMH, or 3.3 V regulated rails without level shifters. An external bus interface provides address/data expansion for external memories or graphics controllers. Architecturally, the ATXMEGA128A4U-AUR uses the Atmel AVR enhanced RISC core with 32 working registers directly connected to the ALU, achieving single-cycle execution. The integrated DMA controller can move data between peripherals and memory without CPU involvement, freeing the core for application code. The 8-channel event system routes peripheral events (timer overflows, ADC conversions, I/O edges) to other peripherals, enabling deterministic hardware-software co-design. The USB 2.0 full-speed transceiver is on-die, requiring only an external pull-up resistor and bypass capacitors. Typical applications include USB HID devices, USB mass storage controllers, industrial sensor hubs with USB diagnostics, low-power data loggers, motor control front ends, and battery-powered handheld instruments. The combination of low active current, deep sleep modes down to sub-microamp, and integrated USB makes it particularly attractive for USB-powered sensor peripherals. Designers also use the A4U family in consumer audio accessories where 12-bit DAC and PWM drive suit headphone or intercom front ends. When designing with this part, budget for the 44-pin TQFP footprint and ensure the USB D+/D- traces are 90 ohm differential-matched. Boot loader and PDI programming share the same pins, so reserve access for in-system programming via the Atmel-ICE or AVR Dragon. The integrated 32 kHz internal RC oscillator can replace an external crystal in space-constrained designs but trades accuracy for BOM savings. This page synthesizes distributor pricing, USB-enabled drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
ATXMEGA128B1-AN - 32MHz 128KB Flash MCU | Microchip
ATXMEGA128B1-AN

ATXMEGA128B1-AN - 32MHz 128KB Flash MCU | Microchip

Microchip Technology ATXMEGA128B1-AN is an 8/16-bit AVR XMEGA microcontroller operating at up to 32 MHz, with 128 KB of self-programming Flash memory and 8 KB of SRAM in a 100-pin TQFP package. The device also includes 2 KB of EEPROM, a 32 MIPS execution rate, and USB Full-Speed device connectivity. According to the Microchip product page, these features suit applications that require embedded control, USB connectivity, segmented displays, and deterministic event handling without relying on an external memory or display controller. An AVR XMEGA microcontroller is an enhanced RISC microcontroller platform that combines a low-power 8/16-bit architecture with integrated Flash, SRAM, EEPROM, and event-driven peripherals. Within the broader semiconductor and embedded-control hierarchy, it sits between general-purpose microcontrollers and highly integrated embedded processors. The ATXMEGA128B1 family is designed to provide more peripheral integration and faster event response than basic 8-bit AVR devices while retaining familiar AVR development workflows. The principal features include 128 KB of Flash organized as 128K x 8, an 8 KB boot-code section, 8 KB of SRAM, 2 KB of EEPROM, and 53 general-purpose I/O lines. Its two-channel DMA controller and four-channel event system support predictable transfers between peripherals without excessive CPU intervention. The integrated USB Full-Speed device controller adds USB connectivity, while the 4 x 40 segment LCD controller can directly drive suitable segmented displays. A maximum operating frequency of 32 MHz supports up to 32 MIPS throughput. The B1 device architecture combines the AVR enhanced RISC core with a programmable multilevel interrupt controller, real-time counter, and hardware event system. Read-while-write Flash operation permits code execution while nonvolatile memory is being accessed, while on-chip SRAM supports time-critical data handling. The manufacturer documents MPLAB Snap debugging through High-Speed USB 2.0 and an 8-pin SIL connector using two I/O pins plus the reset line for in-circuit debugging and in-circuit serial programming. Typical uses include USB-connected human-interface devices, compact industrial controllers, segmented display equipment, data acquisition systems, and low-power embedded control products. The event system is particularly useful when signals from timers, comparators, or external interrupt sources must trigger another peripheral at a predictable time. USB device support can simplify a peripheral design by removing a separate USB interface controller when the required device-class firmware fits the available memory and processing resources. The main PCB-design constraint is the 100-pin TQFP footprint. Use the manufacturer pin-description table when assigning tracks, and place decoupling capacitors close to the appropriate supply pins. Confirm the exact clock, programming interface, USB transceiver requirements, unused-pin treatment, and operating voltage in the manufacturer datasheet before releasing the layout. The 14 x 14 mm package also requires careful consideration of solderability, lead geometry, and manufacturing inspection criteria.

Permintaan RFG Kontak
ATXMEGA128B1-AU 32MHz 128KB Flash MCU | Microchip
ATXMEGA128B1-AU

ATXMEGA128B1-AU 32MHz 128KB Flash MCU | Microchip

The Microchip Technology ATXMEGA128B1-AU is a low-power 8/16-bit AVR XMEGA B1 microcontroller operating at up to 32 MHz, with 128 KB of self-programmable Flash memory and a 100-pin TQFP package measuring 14 x 14 mm. The device provides 8 KB SRAM, a 2 KB boot-code section, and 2 KB EEPROM for firmware, boot code, and persistent data. An 8/16-bit microcontroller is a programmable semiconductor that executes embedded control instructions using an internal CPU, nonvolatile memory, and peripheral interfaces. The AVR XMEGA family combines a Harvard-style memory architecture, high-speed execution, and event-oriented peripherals in a single device. Within the embedded hierarchy, it sits above simple 8-bit controllers because its 16-bit-oriented AVR architecture supports up to 32 MIPS while retaining byte-oriented programming compatibility. The ATXMEGA128B1-AU includes a two-channel DMA controller, a four-channel event system, and a USB Full-Speed device controller. Its memory organization includes 128 KB Flash, 8 KB SRAM, and 2 KB EEPROM, while the LCD interface supports up to 4 x 40 segments. These resources allow firmware movement between memory regions and coordinated handling of events without excessive processor intervention. Up to 53 I/O pins provide access to communication, timer, analog, and general-purpose digital functions. The 100-TQFP arrangement makes the device suitable for compact embedded boards that require extensive peripheral connectivity without using a very large fine-pitch package. Operating voltage options shown for this device include 1.8 V, 2.5 V, and 3.3 V, supporting integration with low-voltage sensors, communications transceivers, and USB interface circuitry. Typical uses include USB-connected data acquisition, industrial control modules, human-machine interfaces, low-power embedded instruments, and segmented LCD equipment. The DMA controller and event system are especially useful when data acquisition, display updates, and communication must coexist with deterministic control-loop execution. The 32 MHz maximum clock rate provides additional timing margin for protocol handling and signal processing. PCB design should preserve short return paths around decoupling capacitors and provide clean routing for USB and clock signals. Firmware development should account for the dedicated boot-code section, interrupt-driven event handling, and peripheral contention between DMA, USB, timers, and the LCD controller. Confirm the exact pin multiplexing, clock configuration, and peripheral availability against the manufacturer datasheet before finalizing a board. This page combines the manufacturer product overview with practical memory, peripheral, package, and sourcing guidance. It also identifies verified same-package alternatives and explains where firmware, timing, or temperature-grade differences must be reviewed before making a replacement decision.

Permintaan RFG Kontak
ATXMEGA128B1-CU - 32MHz 128KB Flash MCU | Microchip
ATXMEGA128B1-CU

ATXMEGA128B1-CU - 32MHz 128KB Flash MCU | Microchip

The Microchip Technology ATXMEGA128B1-CU is an 8/16-bit AVR XMEGA B1 microcontroller with a 32 MHz clock, 128 KB of self-programming Flash memory, and a 100-ball CBGA package. It also provides 8 KB of SRAM, 2 KB of EEPROM, and a 1.6 V to 3.6 V operating supply range. The device integrates USB Full Speed, a two-channel DMA controller, a four-channel event system, and a 53-line general-purpose I/O interface. An 8/16-bit microcontroller is a programmable semiconductor that combines a CPU core, nonvolatile program memory, working memory, peripheral interfaces, and general-purpose I/O in one package. The AVR XMEGA family extends the AVR architecture with hardware resources intended for control, communication, display, data acquisition, and real-time embedded applications. This places the ATXMEGA128B1-CU within the hierarchy of microcontroller, embedded processor, and semiconductor. The 128 KB Flash program memory gives application code and constant data dedicated nonvolatile storage, while the separate 8 KB boot-code section supports protected startup routines. Its 8 KB SRAM accommodates working data, buffers, and interrupt or DMA-driven transfers, and the 2 KB EEPROM retains configuration values when the main supply is removed. The 32 MHz maximum operating frequency supports faster control-loop and peripheral operation. Peripheral integration is a major technical advantage. The two-channel DMA controller can transfer data between peripherals and memory with reduced CPU intervention, while the four-channel event system routes events between timers, DMA channels, and other peripherals. A programmable multilevel interrupt controller manages prioritized event handling. According to the Microchip ATxmega128B1 product page, the device also includes a USB Full Speed device controller and an LCD controller supporting displays up to 4 x 40 segments. Typical uses include USB-connected industrial controls, compact human-machine interfaces, instrumentation, display systems, and real-time embedded products. The USB interface supports direct connectivity to a host, while the large I/O count accommodates sensors, actuators, communication transceivers, and display elements. The integrated DMA and event system are particularly useful when deterministic timing must be maintained alongside USB or display activity. PCB design should follow the manufacturer’s ball-map and layout guidance for the 100-ball package. Place decoupling capacitors at each supply ball as directed, route sensitive signals away from fast-switching nodes, and preserve the required ground-return paths. Confirm the exact ball assignments, exposed-pad arrangement, and reflow profile against the Microchip package documentation before releasing the PCB artwork. This product reference combines the manufacturer’s device capabilities with package-specific selection guidance, practical interface considerations, and direct comparison against the identified same-package ordering variant. It is intended to accelerate engineering evaluation while keeping the final footprint, firmware, and lifecycle decisions tied to Microchip’s official documentation.

Permintaan RFG Kontak
ATXMEGA128B3-AN 32MHz 128KB MCU | Microchip Technology
ATXMEGA128B3-AN

ATXMEGA128B3-AN 32MHz 128KB MCU | Microchip Technology

Microchip Technology ATXMEGA128B3-AN is a low-power 8/16-bit AVR XMEGA microcontroller operating at up to 32 MHz with up to 32 MIPS throughput, 128 KB of self-programmable flash, 4 KB of SRAM, and 2048 bytes of EEPROM in a 64-pin TQFP package. The industrial-temperature ATXMEGA128B3-AN supports a 1.6 V to 3.6 V supply range and operation from -40°C to +105°C. An 8/16-bit AVR microcontroller is a compact embedded-processing device that combines a RISC instruction set, nonvolatile program memory, data memory, timers, communication peripherals, and interrupt handling on one integrated circuit. Within the product hierarchy, the ATXMEGA belongs to the AVR family of 8-bit microcontrollers, the XMEGA series of high-performance 8/16-bit devices, and the broader embedded semiconductor and embedded-control product category. The ATXMEGA128B3 provides 128 KB of in-system self-programmable flash with read-while-write capability, a separate 4 KB boot-code section, 4 KB of SRAM, and 2048 bytes of internal EEPROM. Its integrated peripherals include a two-channel DMA controller, a four-channel event system, a USB full-speed device interface, and an LCD controller supporting as many as 4 by 25 segments. These resources reduce external component requirements in connected control and human-interface designs. The device operates at up to 32 MHz and delivers up to 32 MIPS throughput. Its architecture combines deterministic interrupt handling, direct peripheral access, and hardware event routing with general-purpose processing. The DMA controller can transfer data without continuous CPU intervention, while the event system can connect timer, comparator, and other peripheral events, improving responsiveness in control systems where several timing-sensitive inputs must be coordinated. Typical applications include USB-connected data acquisition, industrial control panels, compact human-interface devices, programmable logic controllers, sensing instruments, and communications equipment. The USB full-speed device interface is particularly useful for a compact peripheral that must exchange configuration or measurement data with a host computer while keeping the MCU operating from a single low-voltage supply. PCB design should follow the manufacturer's package drawing and pin-description tables exactly. Place decoupling capacitors close to the supply pins, preserve the required signal and return paths around USB and high-speed peripherals, and program the operating frequency, clock source, brownout behavior, and peripheral pins through the device's configuration and fuse mechanisms. This page combines manufacturer feature data, package and application guidance, comparison criteria, and drop-in replacement analysis to support faster engineering selection. It is intended to answer the practical questions that arise after identifying the correct controller family: memory capacity, interface availability, temperature range, package compatibility, and PCB reuse.

Permintaan RFG Kontak
ATXMEGA128B3-MCU - 32MHz AVR MCU, 128KB Flash, USB | Microchip
ATXMEGA128B3-MCU

ATXMEGA128B3-MCU - 32MHz AVR MCU, 128KB Flash, USB | Microchip

The Microchip Technology ATXMEGA128B3-MCU is a low-power, high-performance 8/16-bit AVR XMEGA B3 microcontroller with 128KB self-programming Flash, 4KB SRAM, 2KB EEPROM, a 2-channel DMA controller, 4-channel event system, Full-Speed USB Device, 4x25-segment LCD controller, and up to 32 MIPS throughput at 32 MHz, housed in a 64-pin VQFN (7x7 mm) package with exposed pad. A microcontroller unit (MCU) is a single-chip computer integrating a processor core, program and data memory, and peripherals into one package. Within the hierarchy of embedded processors, the AVR XMEGA family sits between small 8-bit AVRs and 32-bit ARM cores, offering 8/16-bit RISC execution with the peripheral richness needed for human-interface and connectivity applications. Key features include 128KB (128K x 8) of self-programming Flash with a 4KB boot code section, enabling field firmware updates over USB or other interfaces; a 4-channel event system that routes peripheral signals without CPU intervention; and a 2-channel DMA controller that offloads data movement for lower CPU load and power consumption. Technically, the AVR RISC core executes most instructions in a single clock cycle, delivering up to 32 MIPS at 32 MHz. The integrated USB Full-Speed Device controller eliminates an external USB interface chip, while the 4x25 segment LCD driver with selectable drive schemes suits battery-powered metering and display products. Typical applications include USB-connected instruments, industrial control panels with LCD displays, battery-powered metering devices, and consumer appliances requiring both USB and segment LCD interfaces. When designing with this device, budget the VQFN-64 exposed-pad footprint for thermal and ground via connections, and verify Flash endurance and supply-voltage ranges against the manufacturer datasheet before finalizing power sequencing. This page synthesizes distributor pricing from LCSC and Heisener, drop-in same-family alternatives, and practical design guidance not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
ATXMEGA128B3-MH - 32MHz 128KB Flash AVR MCU | Microchip
ATXMEGA128B3-MH

ATXMEGA128B3-MH - 32MHz 128KB Flash AVR MCU | Microchip

The Microchip Technology ATXMEGA128B3-MH is a low-power, high-performance 8/16-bit AVR XMEGA B3 microcontroller with a 32 MHz operating frequency, 128 KB of self-programming flash memory, 4 KB SRAM, 2048 bytes of EEPROM, and USB full-speed device support. It is packaged for surface-mount assembly in a 64-QFN 9 x 9 mm package with an exposed thermal pad. The operating voltage range is 1.6 V to 3.6 V. An 8/16-bit AVR microcontroller is an embedded processing device that combines a RISC-style CPU core, nonvolatile program memory, data memory, and peripherals on one integrated circuit. The ATXMEGA128B3 family belongs to the hierarchy of 8/16-bit AVR microcontrollers, embedded controllers, and semiconductor components. Its combination of USB connectivity, event-system peripherals, direct-memory-access support, and mixed signal resources makes it suitable for compact control systems that require more processing and memory than a basic 8-bit MCU. Key device resources include 128 KB of self-programming flash, a separate 4 KB boot-code section, 4 KB of SRAM, and 2048 bytes of EEPROM. The integrated USB full-speed device interface enables USB communication without an external controller. A two-channel DMA controller and four-channel event system support data movement and deterministic peripheral triggering, while the analog and timer resources enable practical acquisition, control, and communication functions. The ATXMEGA128B3-MH is built around Microchip's AVR architecture and runs at up to 32 MHz, providing substantially greater application-code capacity and processing performance than entry-level 8-bit AVR devices. Its 1.6 V to 3.6 V supply range supports low-voltage portable and embedded systems. The 64-QFN 9 x 9 mm package offers a compact land pattern but requires careful PCB layout for its exposed thermal pad and high-speed signal integrity. Typical uses include USB-connected data acquisition, industrial control modules, compact instrumentation, touch-capacitive interfaces, communication equipment, and embedded consumer products. The device is particularly appropriate when a board needs local USB connectivity, moderate program-memory capacity, and deterministic event handling within a relatively small footprint. PCB implementation requires a stable 1.6 V to 3.6 V supply, correct decoupling, a programmed boot and application section, and adequate exposed-pad thermal relief. Designers should follow the Microchip pin-description and package-drawing tables when assigning the 64-QFN lands and should validate USB signal routing and power-supply startup behavior on the final board. This page organizes the device's core specifications, application guidance, verified drop-in alternatives, package considerations, and replacement criteria into one engineering-focused resource for MCU selection and PCB design.

Permintaan RFG Kontak
ATXMEGA128B3-MN - 32MHz 128KB AVR MCU | Microchip
ATXMEGA128B3-MN

ATXMEGA128B3-MN - 32MHz 128KB AVR MCU | Microchip

Microchip Technology ATXMEGA128B3-MN is a low-power 8/16-bit AVR XMEGA B3 microcontroller with a 32 MHz clock, 128 KB self-programming flash, 4 KB SRAM, 2 KB EEPROM, full-speed USB device support, and a 64-VQFN package. The device provides 36 general-purpose I/O lines, a two-channel DMA controller, a four-channel event system, and an LCD controller supporting displays up to 4 × 25 segments. Its operating voltage is 1.6 V to 3.6 V. An AVR XMEGA microcontroller combines an 8-bit microcontroller architecture with a 16-bit instruction set and a wider collection of dedicated peripherals. Within the product hierarchy, it is an 8/16-bit microcontroller, an embedded processing semiconductor, and a member of the power-management-sensitive embedded control category. The XMEGA architecture is intended for designs that require deterministic event handling, direct peripheral routing, and flexible interrupt-driven control without relying on an external interface controller. Key device resources include 128 KB of in-system programmable flash with read-while-write capability, a dedicated 4 KB boot-code section, 4 KB of SRAM, and 2048 bytes of EEPROM. The two-channel DMA controller and four-channel event system can move data and trigger peripheral actions without continuous central-processing-unit intervention. A programmable multilevel interrupt controller, real-time counter, and 36 GPIO lines support responsive embedded-control and human-interface designs. The integrated USB full-speed device interface supports direct USB connectivity, while the LCD driver can operate displays with as many as 4 × 25 segments. These interfaces make the MCU suitable for compact control panels, USB-connected instrumentation, programmable logic controllers, and industrial data-acquisition equipment. The manufacturer datasheet also documents in-system programmable flash, boot support, DMA, event-system resources, real-time timing, and multi-level interrupt handling. Typical uses include USB peripheral control, LCD-based operator interfaces, industrial automation controllers, embedded gateways, and low-power sensor-hub designs. The 32 MHz operating frequency provides useful processing headroom, while the separate boot section permits a dedicated firmware area for startup, recovery, or field-update logic. The EEPROM can retain configuration values without occupying RAM or flash space. Board design should preserve the exposed-pad thermal and electrical connection specified for the 64-VQFN package and route sensitive inputs away from fast-switching nodes. Decoupling, USB impedance-controlled routing, and careful grounding are especially important in compact USB systems. Confirm pin multiplexing, voltage limits, and peripheral conflicts against the manufacturer datasheet before finalizing the PCB. This product page combines the device’s principal memory and connectivity specifications with package, sourcing, replacement, and design considerations. It also organizes the most relevant same-footprint option by its actual ordering-code difference, helping engineers distinguish electrical compatibility from packaging, temperature, or delivery variations before committing a design to production.

Permintaan RFG Kontak
ATXMEGA128C3-AU - 32MHz 128KB AVR Microcontroller | Microchip
ATXMEGA128C3-AU

ATXMEGA128C3-AU - 32MHz 128KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA128C3-AU is an 8/16-bit AVR XMEGA C3 microcontroller with a 32 MHz clock, 128 KB of flash memory, and a 64-pin TQFP package measuring 14 x 14 mm. It combines an 8 KB SRAM, 2 KB EEPROM, 50 general-purpose I/O lines, and a four-channel event system in a low-power embedded-control device designed for industrial, communications, and consumer applications. An AVR XMEGA microcontroller is an 8-bit RISC microcontroller family that combines a modified Harvard architecture, event-driven peripherals, and multi-level interrupt handling. The XMEGA hierarchy extends from the AVR instruction set into the XMEGA family of 8-bit microcontrollers and, more broadly, embedded processors used for real-time control, communications, data acquisition, and human-machine-interface tasks. Key features include 128 KB of in-system programmable flash with read-while-write capability, an 8 KB boot-code section, 8 KB of SRAM, and 2 KB of EEPROM. The four-channel event system connects peripherals through a hardware event channel, reducing CPU intervention for time-critical tasks. A programmable multi-level interrupt controller, 50 GPIO lines, and a 16-bit real-time counter support responsive control loops and periodic services. The device operates from a 1.6 V to 3.6 V supply and is identified as an industrial-temperature TQFP variant. Its 32 MHz performance supports more demanding embedded workloads than smaller AVR devices while retaining the familiar 8-bit AVR programming model. The 64-pin package exposes substantially more I/O than smaller 32-pin and 48-pin MCU packages, making it suitable for boards requiring multiple buses, timers, communication interfaces, or mixed-signal control. Typical uses include industrial control panels, building automation, motor and climate-control systems, metering equipment, data loggers, communications modules, and compact user-interface controllers. The 50 available GPIO lines are particularly useful when an application needs several digital inputs and outputs alongside timer-based control. The ATXMEGA128C3-AU also works with Microchip's MPLAB tool ecosystem and PICkit-compatible programming workflows. For PCB design, provide the manufacturer-recommended decoupling network and route sensitive analog or communication interfaces away from high-current switching nodes. Confirm the complete 64-pin pin-description table, fuse configuration, clock plan, and programming interface against the Microchip datasheet before fabrication. The 14 x 14 mm TQFP footprint also requires a footprint-qualified assembly process with adequate thermal-relief design around the exposed pad area if one is specified. This product record combines the core device specifications, sourcing guidance, programming references, and design considerations engineers need when evaluating the ATXMEGA128C3-AU for a new embedded-control design.

Permintaan RFG Kontak
ATXMEGA128D3-AN - 32MHz 128KB AVR MCU | Microchip | TQFP-64
ATXMEGA128D3-AN

ATXMEGA128D3-AN - 32MHz 128KB AVR MCU | Microchip | TQFP-64

The Microchip Technology ATXMEGA128D3-AN is a low-power, high-performance 8/16-bit AVR XMEGA D3 microcontroller with a 32 MHz operating frequency, 128 KB of ISP Flash memory, 2 KB of EEPROM, and 8 KB of SRAM. The device is supplied in a 64-pin TQFP package measuring 14 x 14 mm and supports operating voltages from 1.6 V to 3.6 V. Its enhanced RISC architecture combines deterministic peripheral handling with 50 general-purpose I/O lines. An AVR XMEGA microcontroller is an 8/16-bit MCU that combines a RISC processing core, embedded Flash and EEPROM, SRAM, timers, event control, communications peripherals, and interrupt handling on one integrated device. The XMEGA D3 family is positioned for low-power, peripheral-rich embedded systems where deterministic event routing, multiple timers, and flexible serial interfaces are more important than a high-performance 32-bit processor core. The ATXMEGA128D3-AN provides 128 KB of read-while-write ISP Flash, including an 8 KB boot-code section, alongside 2 KB of EEPROM and 8 KB of SRAM. Its four-channel event system links peripherals directly to other system functions, reducing processor intervention for timing-sensitive tasks. A programmable multi-level interrupt controller supports structured handling of asynchronous events across the system. Five flexible 16-bit timer/counter modules support compare modes and PWM generation, while a separate 16-bit real-time counter provides another dedicated timing resource. The 50 GPIO lines make the device suitable for control, monitoring, communications, and mixed-signal control systems that require more external connections than a small 20- or 32-pin MCU can offer. Typical uses include industrial control modules, data acquisition units, communications equipment, embedded gateways, sensor controllers, and compact automation products. The 64-pin TQFP package provides substantial I/O and peripheral access while remaining compatible with conventional surface-mount assembly and multilayer PCB layouts. Designers should use the manufacturer pin-description table when assigning every TQFP-64 signal, and should preserve the device's specified decoupling and programming-test requirements. Review the clock, memory, boot, and peripheral configuration sections before finalizing PCB routing and firmware safeguards. This page combines the manufacturer product specifications with focused engineering guidance, package details, lifecycle information, and an explicit assessment of drop-in alternatives. It is intended to help engineers evaluate memory capacity, timing resources, GPIO availability, package compatibility, and sourcing requirements before committing the ATXMEGA128D3-AN to a new design.

Permintaan RFG Kontak
ATXMEGA128D3-MH - 32MHz 128KB AVR MCU | Microchip Technology
ATXMEGA128D3-MH

ATXMEGA128D3-MH - 32MHz 128KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA128D3-MH is an 8-/16-bit AVR XMEGA D3 microcontroller operating at up to 32 MHz, with 128 KB of ISP Flash and 8 KB of SRAM in a 64-QFN 9 x 9 mm package. It combines a 1.6 V to 3.6 V operating range, 2 KB of EEPROM, 50 general-purpose I/O lines, and a four-channel event system in one compact surface-mount package. An 8-/16-bit MCU is a microcontroller whose AVR enhanced RISC core provides a compact instruction set for embedded control. The ATXMEGA128D3 belongs to the XMEGA D3 family within the broader AVR microcontroller and semiconductor hierarchy. It is intended for applications that need more memory and peripherals than a basic 8-bit AVR while retaining a simple, low-power embedded architecture. Its principal resources include 128 KB of ISP Flash organized as 64K x 16, including an 8 KB boot-code section with read-while-write capability. The device also provides 2 KB of EEPROM and 8 KB of SRAM. Four-channel event-system hardware, 50 GPIO lines, a 16-bit real-time counter, and five flexible 16-bit timer/counters support deterministic peripheral timing and reduce reliance on software polling. The 64-QFN package integrates a high-performance, low-power CMOS AVR microcontroller with extensive communication and timing peripherals. A programmable multi-level interrupt controller organizes events across the architecture, while the event system can connect timer, comparator, and other peripheral signals internally. This hardware event routing is useful when several timing-sensitive functions must operate without excessive interrupt-service overhead. Typical uses include industrial control modules, data-acquisition equipment, communications controllers, low-power embedded instruments, and compact automation products. The 50 GPIO lines suit multi-channel sensing or discrete I/O, while the five timer/counters can generate timing references and PWM outputs. The 128 KB Flash capacity also allows larger application code, boot code, and protocol handling within a single device. PCB design should preserve the exposed-pad and thermal requirements of the 64-QFN package while routing sensitive analog, clock, and communication signals according to the manufacturer datasheet. Firmware and fuse compatibility must also be checked against the exact ordering code because XMEGA family members can differ in peripheral availability, memory organization, or qualification. This page combines the manufacturer resource summary, package details, strict same-package alternatives, application guidance, and a parameter comparison to simplify initial component screening. Confirm electrical limits, pin assignments, boot behavior, and programming requirements in the Microchip datasheet before releasing a PCB or production design.

Permintaan RFG Kontak
ATXMEGA128D4-AU - 128KB Flash XMEGA AVR MCU 32MHz 44TQFP | Microchip
ATXMEGA128D4-AU

ATXMEGA128D4-AU - 128KB Flash XMEGA AVR MCU 32MHz 44TQFP | Microchip

The Microchip (Atmel) ATXMEGA128D4-AU is a high-performance, low-power 8/16-bit AVR XMEGA microcontroller integrating 128 KB of in-system programmable Flash with read-while-write support, 2 KB EEPROM, and 8 KB SRAM, housed in a 44-pin TQFP package. It executes instructions at up to 32 MHz from a 1.6-3.6 V supply, with 34 general-purpose I/O lines, two USARTs, two TWI (I2C) interfaces, four flexible 16-bit timer/counters with compare and PWM channels, a 16-bit real-time counter, a four-channel event system, and a programmable multi-level interrupt controller. An 8 KB boot-code section is dedicated for bootloader use, and the device supports AES and DES crypto accelerators plus a 12-bit, 2 MSPS ADC. An 8/16-bit AVR XMEGA microcontroller is an advanced member of Microchip's AVR family combining 8-bit code density with 16-bit peripheral datapaths. It belongs to the broader class of microcontrollers (MCUs) within embedded processors and semiconductors, designed for deterministic real-time control with very low active and sleep-mode power. The XMEGA D4 sub-family specifically targets low-power mixed-signal applications requiring moderate pin counts and rich peripheral integration, sitting above tinyAVR and megaAVR in the Atmel/Microchip MCU hierarchy. Key features include the four-channel event system for inter-peripheral signalling without CPU intervention, a programmable multi-level interrupt controller for deterministic response, a 12-bit 2 MSPS ADC with optional gain stage, and a hardware AES/DES cryptographic engine. The 8 KB boot section allows secure bootloader updates, while the read-while-write Flash enables live firmware upgrades without halting execution. Power-saving features include five sleep modes, a 1.5 µA real-time-counter backup mode, and a peripheral event system that can wake the CPU autonomously. Typical applications include industrial control panels, sensor hubs, low-power wireless sensor nodes, motor control, smart metering, USB device peripherals, consumer white goods, and human-machine interface (HMI) touch panels. The wide 1.6-3.6 V operating range and integrated peripherals make it well suited to battery-powered and energy-harvesting designs. Designers should provide a 0.1 µF decoupling capacitor adjacent to each VCC pin, route analog and digital grounds separately, and observe the 32 MHz maximum system clock. For firmware development, Microchip's Atmel Studio 7 and MPLAB X IDE with the AVR/GNU toolchain target this device directly.

Permintaan RFG Kontak
ATXMEGA128D4-CU - 32MHz 128KB AVR XMEGA MCU | Microchip
ATXMEGA128D4-CU

ATXMEGA128D4-CU - 32MHz 128KB AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA128D4-CU is a low-power 8/16-bit AVR XMEGA microcontroller with a 32 MHz clock, 128 KB of in-system-programmable flash, 2 KB of EEPROM, and 8 KB of SRAM in a 49-pin 5 x 5 mm VFBGA package. The device is built around the enhanced AVR RISC architecture and combines read-while-write flash operation with a four-channel event system and a programmable multilevel interrupt controller. An AVR XMEGA microcontroller is a family of 8/16-bit embedded processors that bridges the gap between simple 8-bit controllers and more complex 16-bit devices. XMEGA devices integrate a Harvard-style RISC core, high-speed timer and counter resources, event routing, serial interfaces, and mixed-signal peripherals into a single low-power design. The ATXMEGA128D4 family is therefore positioned between basic control MCUs and higher-performance 8/16-bit embedded processors. Key features include 128 KB of ISP flash with an 8 KB boot-code section, read-while-write capability, 2 KB of internal EEPROM, 8 KB of internal SRAM, 34 general-purpose I/O lines, and a 16-bit real-time counter. Four flexible 16-bit timer/counter modules provide compare and PWM channels, while the four-channel event system can route signals between peripherals without requiring continuous CPU polling. The communication and control peripheral set includes two USARTs and two two-wire serial interfaces. The 32 MHz operating frequency supports deterministic control loops and high-rate peripheral processing, while the AVR instruction set provides a compact programming model with 16-bit registers and an efficient interrupt structure. The manufacturer datasheet also describes the device as combining high performance, low power, and a peripheral-rich architecture. Typical uses include industrial automation modules, compact data acquisition controllers, motor and position control, industrial networking equipment, and low-power embedded gateways. The 128 KB memory capacity is useful for protocol stacks and application firmware, while the event system can connect timer, comparator, and communication resources for responsive multi-peripheral designs. When laying out the board, place decoupling capacitors directly beside the supply and ground balls and route all 49 package balls according to the manufacturer land pattern. Because this is a fine-pitch BGA device, inspect the assembled PCB with X-ray or equivalent BGA inspection methods and verify continuity with a flying probe or boundary-scan-compatible test process. This page combines manufacturer specifications, package details, sourcing information, and engineering guidance for designers evaluating the ATXMEGA128D4-CU in compact embedded control systems. Use the manufacturer pin and package drawings as the authority for board layout, programming, and production inspection.

Permintaan RFG Kontak
ATXMEGA128D4-MH - 32MHz AVR XMEGA D4 MCU 128KB Flash | Microchip
ATXMEGA128D4-MH

ATXMEGA128D4-MH - 32MHz AVR XMEGA D4 MCU 128KB Flash | Microchip

The Microchip (formerly Atmel) ATXMEGA128D4-MH is a high-performance, low-power 8/16-bit AVR XMEGA D4 microcontroller combining 128 KB ISP Flash memory with read-while-write capability, 2 KB EEPROM, and 8 KB SRAM, operating at up to 32 MHz and housed in a 44-pin VQFN (7x7 mm) package with exposed thermal pad. The device supports an operating voltage of 1.6 V to 3.6 V and provides 34 programmable I/O pins, a four-channel event system, programmable multi-level interrupt controller, and a DMA controller for CPU-off data movement. According to the manufacturer datasheet, the XMEGA D4 series is positioned for low-power applications requiring rich peripheral integration without sacrificing throughput. An AVR XMEGA microcontroller is a member of the 8/16-bit RISC microcontroller family based on the enhanced AVR architecture, sitting in the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. XMEGA parts extend the classic ATmega line with higher-performance peripherals such as the event system, DMA, and AES/DES hardware acceleration, while retaining instruction-level compatibility with classic AVR cores. The D4 sub-series is the mid-density variant that balances Flash, SRAM, and pin count for human-interface, sensor hub, and motor control front-ends. Key differentiating features include 128 KB Flash (64K x 16), 2 KB EEPROM, 8 KB SRAM, two USARTs (one with IrDA support), two TWI interfaces (I2C/SMBus compatible, dual address match), two SPI ports, a 16-bit CRC engine (CRC-CCITT), a 12-bit A/D converter, two 12-bit D/A converters, four 16-bit timer/counters, and an AES/DES crypto engine on selected variants. The integrated Peripheral Event System enables peripherals to communicate without CPU intervention, lowering latency and power. Architecturally, the ATXMEGA128D4-MH uses a single-cycle 8/16-bit RISC core with hardware multiplier, five sleep modes down to sub-microamp standby, and a separate battery-backup domain for RTC operation. The 32 MHz peak throughput (with 2.7-3.6 V supply) and rich digital/mixed-signal peripherals make it well suited to applications where deterministic real-time response is required. Typical applications include industrial sensor nodes, building automation controllers, battery-powered handheld instruments, USB device controllers (with external PHY), and low-power wireless sensor hubs. Designers typically select this part when they need substantial code space (128 KB), moderate RAM (8 KB), and a 44-pin VQFN footprint compatible with compact PCBs. When designing with the ATXMEGA128D4-MH, note that the 1.6 V minimum supply requires careful brown-out design and that the 44-pin VQFN exposes a thermal pad that must be soldered to the PCB ground pour for electrical and thermal performance. Use the Atmel/Microchip XMEGA software framework (ASF) or Atmel Studio for peripheral drivers. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes not found in the manufacturer datasheet alone, giving engineers a one-stop reference for sourcing and validating the ATXMEGA128D4-MH.

Permintaan RFG Kontak
ATXMEGA16A4-AU - 32MHz 16KB AVR MCU | Microchip Technology
ATXMEGA16A4-AU

ATXMEGA16A4-AU - 32MHz 16KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA16A4-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 16 KB self-programming Flash memory, 2 KB SRAM, and 1 KB EEPROM in a 44-pin TQFP package. According to the Microchip product page, the device is not recommended for new designs and should be replaced by an XMEGA AU-series device. An AVR XMEGA microcontroller is an embedded-control semiconductor that combines an enhanced RISC processor core, Flash program memory, SRAM, EEPROM, event-system hardware, direct-memory-access support, and multiple communication peripherals. It belongs to the hierarchy of 8/16-bit microcontroller, embedded processor, and system-on-chip products intended for control-oriented products where deterministic event handling, low-power operation, and extensive on-chip peripherals can reduce external component count. The ATXMEGA16A4 family provides 16 KB self-programming Flash with Read-While-Write capability, including a 4 KB boot-code section, and supplies up to 34 general-purpose I/O lines. Its four-channel DMA controller and eight-channel Event System can move data and trigger peripherals without repeated CPU intervention. The peripheral set includes a 16-bit real-time counter, five flexible 16-bit timer/counters with compare and PWM modes, and multiple USART and serial-interface resources for connected industrial and consumer equipment. The device supports an operating supply range of 1.6 V to 3.6 V, while common 1.8 V, 2.5 V, and 3.3 V rails are identified in the comparison information. It can execute at 32 MHz and is positioned for applications requiring up to 32 MIPS throughput. Its event system and hardware DMA are especially useful when timing relationships between sensors, timers, communication blocks, and control outputs must remain deterministic without continuous software polling. Typical uses include industrial control modules, compact sensor nodes, data-acquisition controllers, communication equipment, low-power embedded instruments, and compact consumer devices. The 44-pin TQFP package provides enough I/O for mixed analog and digital control systems while remaining compatible with conventional surface-mount assembly. The large SRAM and EEPROM also support buffered protocol handling, parameter storage, calibration records, and firmware state that would otherwise require external memory. Design should account for the 1.6 V to 3.6 V operating range and confirm that attached peripherals use voltage-compatible signal levels. Decoupling, clock stability, programming access, and exposed peripheral routing should follow the pin-description and recommended-circuit diagrams in the manufacturer datasheet. Firmware migration should also confirm boot-loader behavior, peripheral differences, and clock settings before reusing an existing ATXMEGA16A4 design in a new product. This page consolidates the device architecture, verified manufacturer and distributor specifications, same-footprint family alternatives, and practical replacement guidance. It also distinguishes direct procurement information from design parameters so engineers can evaluate the obsolete-position device, migration options, and application fit without relying on a raw listing alone.

Permintaan RFG Kontak
ATXMEGA16A4-CU - 32MHz 16KB AVR MCU | Microchip Technology
ATXMEGA16A4-CU

ATXMEGA16A4-CU - 32MHz 16KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA16A4-CU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 16 KB self-programming Flash memory, 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM in a 49-VFBGA 5 x 5 mm package. Its 1.6 V to 3.6 V operating-supply range supports low-voltage embedded designs where component size, processing speed, and local memory integration are important. The CU suffix identifies the compact 49-ball package configuration. An 8/16-bit microcontroller is a semiconductor that executes embedded control instructions and connects digital peripherals to a larger product. The AVR enhanced RISC architecture belongs to the microcontroller hierarchy: MCU, embedded processor, integrated circuit, and semiconductor. Compared with a larger general-purpose MCU, the ATXMEGA family targets compact control systems that require deterministic peripheral operation, efficient code execution, and low-power characteristics. The headline features combine 32 MHz processing with 16 KB Flash, 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM. The separate boot-code area can hold code used for boot operations, while the SRAM supports working data and the EEPROM provides nonvolatile storage. The device also includes an external bus interface, expanding its connection options for embedded systems that need access to external peripherals or memory. The ATXMEGA16A4 is based on the AVR enhanced RISC architecture and belongs to Microchip's XMEGA A4 family. Its 8/16-bit architecture is suitable for compact embedded control tasks combining interrupt-driven peripherals, serial communication, and local data storage. Because the verified manufacturer information identifies the A4 series as not recommended for new designs, engineers should evaluate the recommended XMEGA AU series before beginning a new product design. Typical uses include compact industrial controllers, sensor-hub and IoT edge nodes, low-power embedded instruments, and portable products requiring 1.6 V to 3.6 V operation. The 49-VFBGA package also supports space-constrained designs, although its fine pitch requires careful PCB layout and assembly. The 16 KB Flash and 2 KB SRAM limit memory-intensive workloads, so protocol buffering or complex user interfaces may require external components. A critical design consideration is lifecycle status: Microchip lists ATXMEGA16A4 as not recommended for new designs and recommends the XMEGA AU series. For an existing ATXMEGA16A4-CU design, preserve the exact 49-VFBGA footprint, validate the original power, clock, peripheral, and memory assumptions, and avoid treating a family-related device as a drop-in replacement without a complete pin and firmware review. This page consolidates verified manufacturer and distributor information for ATXMEGA16A4-CU, including memory configuration, package constraints, sourcing links, lifecycle guidance, and engineering-oriented application analysis. It also clearly separates verified device data from replacement candidates that were not demonstrated to be pin-to-pin compatible.

Permintaan RFG Kontak
ATXMEGA16A4-CUR - 32MHz 16KB AVR MCU | Microchip Technology (Tape & Reel)
ATXMEGA16A4-CUR

ATXMEGA16A4-CUR - 32MHz 16KB AVR MCU | Microchip Technology (Tape & Reel)

The Microchip Technology ATXMEGA16A4-CUR is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 16 KB self-programming Flash memory, 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM in a 49-VFBGA 5 x 5 mm package. Its 1.6 V to 3.6 V operating-supply range supports low-voltage embedded designs where component size, processing speed, and local memory integration are important. The CU suffix identifies the compact 49-ball package configuration. An 8/16-bit microcontroller is a semiconductor that executes embedded control instructions and connects digital peripherals to a larger product. The AVR enhanced RISC architecture belongs to the microcontroller hierarchy: MCU, embedded processor, integrated circuit, and semiconductor. Compared with a larger general-purpose MCU, the ATXMEGA family targets compact control systems that require deterministic peripheral operation, efficient code execution, and low-power characteristics. The headline features combine 32 MHz processing with 16 KB Flash, 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM. The separate boot-code area can hold code used for boot operations, while the SRAM supports working data and the EEPROM provides nonvolatile storage. The device also includes an external bus interface, expanding its connection options for embedded systems that need access to external peripherals or memory. The ATXMEGA16A4 is based on the AVR enhanced RISC architecture and belongs to Microchip's XMEGA A4 family. Its 8/16-bit architecture is suitable for compact embedded control tasks combining interrupt-driven peripherals, serial communication, and local data storage. Because the verified manufacturer information identifies the A4 series as not recommended for new designs, engineers should evaluate the recommended XMEGA AU series before beginning a new product design. Typical uses include compact industrial controllers, sensor-hub and IoT edge nodes, low-power embedded instruments, and portable products requiring 1.6 V to 3.6 V operation. The 49-VFBGA package also supports space-constrained designs, although its fine pitch requires careful PCB layout and assembly. The 16 KB Flash and 2 KB SRAM limit memory-intensive workloads, so protocol buffering or complex user interfaces may require external components. A critical design consideration is lifecycle status: Microchip lists ATXMEGA16A4 as not recommended for new designs and recommends the XMEGA AU series. For an existing ATXMEGA16A4-CUR design, preserve the exact 49-VFBGA footprint, validate the original power, clock, peripheral, and memory assumptions, and avoid treating a family-related device as a drop-in replacement without a complete pin and firmware review. This page consolidates verified manufacturer and distributor information for ATXMEGA16A4-CUR, including memory configuration, package constraints, sourcing links, lifecycle guidance, and engineering-oriented application analysis. It also clearly separates verified device data from replacement candidates that were not demonstrated to be pin-to-pin compatible.

Permintaan RFG Kontak
ATXMEGA16A4-MH - 32MHz 16KB AVR MCU | Microchip Technology
ATXMEGA16A4-MH

ATXMEGA16A4-MH - 32MHz 16KB AVR MCU | Microchip Technology

Microchip Technology ATXMEGA16A4-MH is a low-power 8/16-bit AVR XMEGA A4 microcontroller with 32 MHz maximum clock speed, 16 KB self-programming Flash memory, and a 44-pin VQFN 7 x 7 mm package. The device also includes 4 KB of boot-code memory, 2 KB of SRAM, and 1 KB of EEPROM for firmware, boot code, and nonvolatile data storage. An 8/16-bit AVR microcontroller is a compact embedded-processing component that combines a CPU core, Flash program memory, data memory, and peripherals on one semiconductor die. Within the product hierarchy, ATXMEGA16A4-MH belongs to the AVR XMEGA family, the XMEGA A4 series, microcontrollers, and the broader embedded-processing semiconductor category. Its enhanced AVR RISC architecture supports applications requiring deterministic peripheral control and efficient low-power operation. Key features include four-channel direct-memory-access support, an eight-channel event system, a programmable multilevel interrupt controller, and 34 general-purpose I/O lines. The peripheral set also includes a 16-bit real-time counter, five flexible 16-bit timer/counters with compare and PWM modes, five USARTs, and internal read-while-write Flash operation. These resources reduce the need for external interface and timing components in compact control systems. The XMEGA A4 architecture combines single-cycle instruction execution with integrated DMA, event routing, and interrupt priorities. Five USARTs allow multiple serial links to coexist, while the event system can connect peripherals without continuous CPU intervention. The 32 MHz operating speed and 16 KB Flash capacity are suitable for compact embedded products that need substantial serial communications, timing, and general-purpose I/O without moving to a larger package or higher-memory device. Typical applications include industrial control modules, multi-interface data acquisition units, building automation controllers, serial protocol bridges, compact instrumentation, and low-power embedded gateways. Designers can use the USARTs for service, sensor, and host interfaces; the timer/counters for motor, PWM, or waveform functions; and the event system to coordinate peripheral actions efficiently. A primary design consideration is lifecycle planning. The Microchip product page identifies ATXMEGA16A4 as not recommended for new designs and directs new projects toward the XMEGA AU series. Existing designs should therefore validate package, firmware, supply, and qualification requirements before migration, while new projects should assess whether the recommended successor offers a practical path. This product overview combines manufacturer specifications, lifecycle guidance, drop-in candidate evaluation, interface-oriented design guidance, and application selection criteria to support faster engineering review and sourcing decisions.

Permintaan RFG Kontak
ATXMEGA16A4U-AN 32MHz AVR XMEGA MCU | Microchip Technology
ATXMEGA16A4U-AN

ATXMEGA16A4U-AN 32MHz AVR XMEGA MCU | Microchip Technology

The Microchip Technology ATXMEGA16A4U-AN is an 8/16-bit AVR XMEGA microcontroller operating up to 32 MHz with up to 32 MIPS performance, 16 KB of self-programming Flash memory, and a 44-pin TQFP package measuring 10 mm by 10 mm. It also provides 2 KB of SRAM, 1 KB of EEPROM, 34 general-purpose I/O lines, and a 1.6 V to 3.6 V operating-voltage range. An AVR XMEGA microcontroller is a low-power embedded-control semiconductor that combines an AVR RISC processor core, program and data memories, peripheral timers, communications interfaces, analog converters, and event-driven peripherals. Within the device hierarchy, it is an 8/16-bit microcontroller, a type of embedded processor and system-on-chip designed for compact industrial, consumer, communications, and control applications. Key features include 16 KB of Flash program memory with read-while-write operation, a 4 KB boot-code section, 2 KB of SRAM, and 1 KB of EEPROM. The peripheral set includes a four-channel DMA controller, an eight-channel event system, a 16-bit real-time counter, five flexible 16-bit timer/counters, and five USARTs. These resources allow firmware to transfer data and trigger peripheral actions without relying on extensive CPU polling. The ATXMEGA16A4U architecture supports up to 32 MIPS at a 32 MHz clock and provides an external bus interface alongside programmable interrupt handling. The 34 I/O pins give a design maker access to digital inputs, outputs, and multiplexed peripheral functions. Its combination of event-system routing, DMA, timers, and serial interfaces is especially useful when multiple timing-sensitive tasks must operate predictably within a compact embedded-control design. Typical applications include industrial sensor controllers, serial gateways, motor and motion-control equipment, instrumentation, low-power data acquisition, and embedded communications equipment. The TQFP-44 package also makes the device practical for designs requiring a conventional surface-mount footprint rather than a very small leadless package. Designers should preserve adequate decoupling at the supply pins, route sensitive analog inputs away from fast-switching nodes, and confirm pin assignments and peripheral multiplexing in the manufacturer pin-description table. Because the A4U and non-U A4 families differ in integrated peripherals, replacing the non-U device with ATXMEGA16A4U-AN can require firmware and board-level review rather than only a component substitution. This product page combines manufacturer specifications, drop-in replacement analysis, package details, and practical design guidance to support component selection, schematic review, PCB planning, and firmware migration for the ATXMEGA16A4U-AN.

Permintaan RFG Kontak
ATXMEGA16A4U-AU - 32MHz 16KB Flash AVR XMEGA MCU | Microchip
ATXMEGA16A4U-AU

ATXMEGA16A4U-AU - 32MHz 16KB Flash AVR XMEGA MCU | Microchip

The Microchip ATXMEGA16A4U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller running up to 32 MHz (32 MIPS) with 16 KB of in-system self-programming Flash, 2 KB SRAM, 1 KB EEPROM and a 4 KB boot code section, housed in a 44-pin TQFP (10x10 mm) package. An MCU (microcontroller) is a single-chip computer integrating a CPU core, program memory, data memory, and peripherals such as ADC, timers, and communication interfaces. The AVR XMEGA A4U family specifically occupies the 8/16-bit low-power tier of the AVR RISC architecture hierarchy, sitting below 32-bit ARM Cortex-M parts but above legacy 8-bit ATmega families in performance and peripheral richness. It targets battery-powered and mixed-signal embedded designs where deterministic behavior, fast interrupts, and rich analog integration matter more than raw MHz. Key features of the ATXMEGA16A4U-AU include 16 KB Flash with Read-While-Write support, a 4-channel DMA controller that off-loads the CPU from peripheral data movement, an 8-channel Event System for inter-peripheral signaling without CPU intervention, 34 general-purpose I/O lines, a 16-bit Real Time Counter (RTC), five 16-bit Timer/Counters, five USARTs, two TWI (I2C-compatible) ports, one SPI, a USB 2.0 Full-Speed device interface, and a 12-bit ADC with up to 12 channels plus dual 12-bit DAC channels. The peripheral set is unusually broad for a 16 KB Flash part. Architecturally, the device uses the Atmel AVR enhanced RISC core with a two-stage pipeline, hardware multiplier, and a programmable multi-level interrupt controller. The 1.6 V to 3.6 V supply range and low-power sleep modes with RTC retention make it attractive for energy-harvesting and always-on applications. Typical applications include USB HID peripherals, industrial sensor nodes, low-power wireless sensor hubs, building automation controllers, smart metering, LED lighting controllers with smooth dimming, and battery-backed IoT edge nodes. The integrated USB FS device is the distinguishing capability versus the non-U XMEGA A4 variants. When designing with this MCU, allocate the 4 KB boot section for bootloader code so application firmware can use the full 16 KB, and provide a 32.768 kHz crystal on the RTC pins if RTC accuracy matters. The PDI programming interface requires only two pins, freeing most of the GPIO for application use. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet narrative.

Permintaan RFG Kontak
ATXMEGA16A4U-AUR - 16KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA16A4U-AUR

ATXMEGA16A4U-AUR - 16KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA16A4U-AUR is an 8/16-bit AVR XMEGA A4U microcontroller running up to 32MHz with 16KB of in-system self-programmable Flash, 2KB SRAM and 1KB EEPROM, housed in a 44-pin TQFP (10x10 mm) industrial-temperature package delivered on Tape & Reel. It features a 4-channel DMA controller, an 8-channel event system, a full-speed USB 2.0 device/host interface, and up to 32 MIPS throughput from the rich AVR RISC instruction set with 32 general-purpose working registers directly connected to the ALU. An XMEGA A4U microcontroller is a high-performance, low-power 8/16-bit AVR RISC core member of the Atmel/Microchip AVR XMEGA family, which itself sits within the broader hierarchy of microcontrollers (MCU) -> embedded processors -> integrated circuits -> semiconductors. XMEGA parts combine a 2-cycle hardware multiplier, a peripheral event system, and a multi-channel DMA to deliver deterministic, low-overhead I/O that is well suited to battery-powered and signal-conditioning designs. The 'U' suffix specifically denotes a USB 2.0 full-speed (12 Mbps) transceiver, while the 'A4U' series provides 4-channel DMA, 8-channel event system, and an external bus interface for SRAM, SDRAM and NAND expansions. Key differentiators of the ATXMEGA16A4U-AUR include 16KB Flash (vs 8/4KB on smaller XMEGA A-series siblings), on-chip USB 2.0 full-speed transceiver supporting device, host, and OTG roles, AES and DES crypto accelerators for secure firmware updates, an integrated 12-bit 1 MSPS ADC, a 12-bit 1 MSPS DAC, four USARTs, two TWI (I2C) ports, and two SPI ports. The peripheral event system allows direct hardware triggering between timers, ADC, DAC, DMA, and I/O without CPU intervention, while the 4-channel DMA controller offloads repetitive data moves to maintain real-time responsiveness. Typical applications include USB HID/mass-storage peripherals, industrial sensor front-ends with USB logging, secure IoT edge nodes with AES encryption, portable data loggers, and battery-powered human-interface devices (HID) such as custom keyboards, mice, or capacitive-touch control panels. The wide 1.6V to 3.6V supply range and picoPower sleep modes support designs that spend long periods in standby and wake on USB events. Design considerations include careful decoupling of the analog and digital VCC rails, provision for a 12 MHz crystal or external clock for USB full-speed operation, and reserving PA0/PA1 for the USB D-/D+ pins since the on-chip transceiver is bonded to those pads. The 4KB bootloader section with independent lock bits enables in-field firmware upgrades.

Permintaan RFG Kontak
ATXMEGA16A4U-MH - 32MHz 16KB Flash MCU | Microchip
ATXMEGA16A4U-MH

ATXMEGA16A4U-MH - 32MHz 16KB Flash MCU | Microchip

Microchip Technology ATXMEGA16A4U-MH is an 8/16-bit AVR XMEGA A4U microcontroller operating at up to 32 MHz, with 16 KB of self-programming Flash memory, 2 KB of SRAM, and 1 KB of EEPROM in a 44-pin VQFN package measuring 7 x 7 mm. The device supports 1.8 V, 2.5 V, and 3.3 V operation and provides an external bus interface, a 4-channel DMA controller, and an 8-channel event system. An 8/16-bit microcontroller is a programmable semiconductor that combines a CPU core, memory, and peripherals on one integrated circuit. The AVR XMEGA family belongs to the broader embedded-controller hierarchy, using a Harvard-style RISC architecture designed to execute instructions efficiently while balancing processing performance, low-power operation, and peripheral integration. The ATXMEGA16A4U-MH is intended for compact embedded systems that require more event handling and data-transfer flexibility than a basic 8-bit MCU provides. The principal features include 32 KB self-programming Flash, a dedicated 4 KB boot-code section, 2 KB SRAM, and 1 KB EEPROM. A 4-channel DMA controller can move data between peripherals and memory while reducing CPU intervention, while the 8-channel event system can connect timer, comparator, and other peripheral events. Up to 32 GPIO functions are associated with the device family, making it suitable for control, communication, and mixed-signal interface applications. The AVR enhanced RISC architecture provides up to 32 MIPS at a 32 MHz clock according to the manufacturer datasheet. Separate programming and data memories give deterministic access to code and working data. Self-programming Flash permits field-update workflows when the application includes a valid bootloader and appropriate firmware protection. The A4U device also integrates communication and timing resources suitable for connected industrial, consumer, and embedded-control products. Typical uses include low-power sensor nodes, compact motor and actuator controllers, industrial interface modules, USB-enabled human-interface equipment, and embedded control boards requiring DMA or event-driven peripherals. The 7 x 7 mm VQFN land pattern supports compact designs, while its exposed-pad construction requires careful thermal and PCB-layout treatment. The A4U family is also a natural choice when firmware needs deterministic event routing and efficient peripheral transfers without a higher-memory MCU. For PCB implementation, place the decoupling network at the supply pins and preserve the exposed pad's thermal and electrical continuity with a solderable copper area. Confirm that the production PCB footprint matches the 44-pin VQFN arrangement, exposed-pad dimensions, and paste mask before layout release. Programmers and debuggers must also be checked for compatibility with the selected AVR XMEGA device and selected operating voltage. This page organizes the core memory, timing, package, and peripheral characteristics into a practical selection reference. It also identifies same-package XMEGA family alternatives, highlights memory-density differences, and provides design guidance for PCB layout, firmware migration, and feature-based replacement decisions.

Permintaan RFG Kontak
ATXMEGA16C4-AN - 32MHz 16KB AVR Microcontroller | Microchip
ATXMEGA16C4-AN

ATXMEGA16C4-AN - 32MHz 16KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA16C4-AN is a low-power 8/16-bit AVR XMEGA microcontroller with a 32 MHz maximum clock, 16 KB in-system programmable Flash memory, 1 KB EEPROM, and 2 KB SRAM in a 44-pin TQFP package. It combines an enhanced RISC core with four-channel event system support, 34 general-purpose I/O lines, and extensive serial communications peripherals for embedded control applications. An AVR XMEGA microcontroller is an 8/16-bit RISC controller designed to balance processing throughput, deterministic event handling, and low-power operation. In the product hierarchy, the ATXMEGA16C4-AN belongs to the AVR XMEGA family of 8/16-bit microcontrollers, combining a compact embedded CPU with timers, serial interfaces, analog conversion functions, and programmable event-system resources. Its enhanced RISC architecture supports single-clock-cycle instruction execution for responsive control loops. The device provides 16 KB of Flash, including a dedicated 4 KB boot-code section with read-while-write capability. It also includes 1 KB of internal EEPROM for nonvolatile configuration data and 2 KB of SRAM for working memory. Four 16-bit timer/counter modules support timing and PWM functions, while three USARTs and two TWI interfaces provide serial connectivity for sensors, human-interface equipment, and industrial control networks. The four-channel event system is a key architectural feature for coordinating activities without relying entirely on interrupt service routines. A programmable multilevel interrupt controller organizes events by priority, and the 16-bit real-time counter provides a dedicated timekeeping resource. Together, these features are useful when several inputs must be sampled, filtered, or reacted to with predictable timing. Typical uses include industrial control modules, sensor hubs, motor controllers, communication bridges, compact data loggers, and embedded gateways. The 34 GPIO pins make the ATXMEGA16C4-AN suitable for designs that need multiple digital interfaces without adding a separate programmable logic device. Its 32 MHz operating ceiling also supports time-sensitive protocol handling and higher-rate control tasks. Designers should verify every signal assignment and voltage-domain connection against the manufacturer pin-description table before routing the PCB. Pay particular attention to supply pins, decoupling, programming interfaces, and any pins configured for analog functions. Confirm the device's full electrical limits, ADC performance, clock options, and absolute maximum ratings before releasing a production design. This product page combines the manufacturer device specifications, exact-package information, practical application guidance, pin-compatible migration considerations, and engineering-focused comparison data. It is intended to support component selection, schematic review, firmware planning, and PCB footprint verification without replacing the complete manufacturer documentation.

Permintaan RFG Kontak