ATXMEGA128D4-CU - 32MHz 128KB AVR XMEGA MCU | Microchip
MPN: ATXMEGA128D4-CU ✓ AktifATXMEGA128D4-CU Ringkasan
An AVR XMEGA microcontroller is a family of 8/16-bit embedded processors that bridges the gap between simple 8-bit controllers and more complex 16-bit devices. XMEGA devices integrate a Harvard-style RISC core, high-speed timer and counter resources, event routing, serial interfaces, and mixed-signal peripherals into a single low-power design. The ATXMEGA128D4 family is therefore positioned between basic control MCUs and higher-performance 8/16-bit embedded processors.
Key features include 128 KB of ISP flash with an 8 KB boot-code section, read-while-write capability, 2 KB of internal EEPROM, 8 KB of internal SRAM, 34 general-purpose I/O lines, and a 16-bit real-time counter. Four flexible 16-bit timer/counter modules provide compare and PWM channels, while the four-channel event system can route signals between peripherals without requiring continuous CPU polling.
The communication and control peripheral set includes two USARTs and two two-wire serial interfaces. The 32 MHz operating frequency supports deterministic control loops and high-rate peripheral processing, while the AVR instruction set provides a compact programming model with 16-bit registers and an efficient interrupt structure. The manufacturer datasheet also describes the device as combining high performance, low power, and a peripheral-rich architecture.
Typical uses include industrial automation modules, compact data acquisition controllers, motor and position control, industrial networking equipment, and low-power embedded gateways. The 128 KB memory capacity is useful for protocol stacks and application firmware, while the event system can connect timer, comparator, and communication resources for responsive multi-peripheral designs.
When laying out the board, place decoupling capacitors directly beside the supply and ground balls and route all 49 package balls according to the manufacturer land pattern. Because this is a fine-pitch BGA device, inspect the assembled PCB with X-ray or equivalent BGA inspection methods and verify continuity with a flying probe or boundary-scan-compatible test process.
This page combines manufacturer specifications, package details, sourcing information, and engineering guidance for designers evaluating the ATXMEGA128D4-CU in compact embedded control systems. Use the manufacturer pin and package drawings as the authority for board layout, programming, and production inspection.
Alternatif penggantian untuk ATXMEGA128D4-CU — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ATXMEGA128D4-CU (sama faktor bentuk dan footprint) — berbeda di dalam Package, SRAM, Flash Memory, EEPROM, Boot Code Section.
ATXMEGA64D4-CU
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →ATXMEGA32D4-CU
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →ATXMEGA16D4-CU
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →ATXMEGA32C4-CU
✅ Drop-InKontak untuk harga
Lihat Datasheet →ATXMEGA128D4-CU Rating Maksimal & Karakteristik Listrik
| Product Type | 8/16-bit AVR XMEGA microcontroller |
| Frekuensi Bawah Maximum | 32 MHz |
| Flash Memory | 128 KB |
| Flash Organization | 64K x 16 |
| Boot Code Section | 8 KB |
| EEPROM | 2 KB |
| SRAM | 8 KB |
| Supply Voltage Range | 1.6 V to 3.6 V |
| General-Purpose I/O Lines | 34 |
| Timer/Counter Modules | 4 flexible 16-bit timer/counter modules |
| Event System | 4 channels |
| Real-Time Counter | 16-bit |
| USART Controllers | 2 |
| Two-Wire Serial Interfaces | 2 |
| Paket | 49-pin VFBGA, 5 x 5 mm |
| Tipe Mounting | Surface mount |
| Instruction Set | AVR enhanced RISC |
| Interrupt Controller | Programmable multilevel interrupt controller |
| Status RoHS | RoHS listed |
ATXMEGA128D4-CU 49-pin vfbga, 5 x 5 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk ATXMEGA128D4-CU (49-pin vfbga, 5 x 5 mm pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk ATXMEGA128D4-CU.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ATXMEGA128D4-CU cocok untuk 6 aplikasis: Industrial Automation Controller, Data Acquisition and Sensor Hub, Serial Protocol Gateway, Motor and Position Control, Low-Power Embedded Gateway, Programmable Control and Test Equipment.
Industrial Automation Controller
The ATXMEGA128D4-CU fits compact industrial control modules that must combine protocol handling, deterministic timing, and local data processing. Its 128 KB of flash accommodates application firmware and an 8 KB boot-code section, while 8 KB of SRAM supports protocol buffers and control state. Four flexible 16-bit timer/counter modules provide capture, compare, and PWM resources for encoder inputs, motor timing, and solenoid control. The 34 general-purpose I/O lines also reduce the need for external I/O expanders. Use the 1.6 V to 3.6 V operating range to plan the regulator and protection strategy around the industrial supply rail.
Direkomendasikan
Data Acquisition and Sensor Hub
The ATXMEGA128D4-CU is appropriate for a multi-sensor data-acquisition hub because its 34 I/O lines can accommodate digital inputs, status indicators, and external converters. The 32 MHz clock provides ample headroom for sampling schedules and short communication transactions, while the four-channel event system can connect timing events with serial or counter resources. Its 2 KB EEPROM is useful for calibration constants and configuration records, and the 128 KB flash leaves room for buffering logic, communication stacks, and field-upgrade support. Place analog front-end circuitry away from high-switching nodes and use the 34 I/O budget carefully when planning multiplexing.
Direkomendasikan
Serial Protocol Gateway
The ATXMEGA128D4-CU works well in a protocol-conversion gateway because it combines two USARTs with two two-wire serial interfaces and 128 KB of program flash. This allows one module to bridge legacy RS-232 or RS-485 equipment to an embedded network or sensor bus while maintaining local buffering in SRAM. Four 16-bit timer/counter modules can support baud-rate generation, protocol timeouts, and periodic data acquisition. The 1.6 V to 3.6 V range gives designers flexibility around 1.8 V and 3.3 V transceivers, but each serial interface still needs proper line-driver protection, isolation, or termination where the cable environment requires it.
Direkomendasikan
Motor and Position Control
The ATXMEGA128D4-CU can serve as the controller for small motors, encoders, and position-feedback systems where deterministic timing and PWM resources matter. Its four 16-bit timer/counter modules offer independent compare and PWM channels, allowing encoder capture, velocity measurement, and motor drive timing to coexist. The 32 MHz CPU supports responsive control loops, and the 34 I/O lines can accept limit switches, position sensors, and digital encoder signals. Its 8 KB SRAM is adequate for short control histories, while 128 KB of flash provides room for tuning algorithms and field-service features. Keep switching-node routing away from encoder inputs to prevent timing and accuracy degradation.
Direkomendasikan
Low-Power Embedded Gateway
The ATXMEGA128D4-CU is a strong candidate for compact, low-power embedded gateways that periodically collect information and transmit it over a serial link. Its AVR enhanced RISC architecture provides efficient code density, while the 128 KB flash reduces the need for external storage and supports over-the-air update logic. The event system can coordinate timers, communication activity, and external events so the processor does not need to poll every peripheral continuously. Use the 1.6 V minimum operating voltage to reduce regulator losses in battery or energy-harvested systems, and confirm the active current and wake-up behavior against the application duty cycle.
Direkomendasikan
Programmable Control and Test Equipment
The ATXMEGA128D4-CU is useful in compact automated test fixtures and programmable measurement controllers where multiple timing channels and communication ports are required. The four 16-bit timer/counter modules can drive stimulus timing or count test events, while the two USARTs and two two-wire interfaces connect instruments and sensors. With 128 KB of flash, 8 KB of SRAM, and 34 I/O lines, the controller can combine test sequencing, local data capture, and host communication in one device. Use calibrated clock and reference routing for accurate timing, and validate the complete 49-ball BGA assembly electrically because inaccessible solder defects may otherwise appear only during operation.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ATXMEGA128D4-CU — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ATXMEGA64D4-CU | ATXMEGA32D4-CU | ATXMEGA16D4-CU | ATXMEGA32C4-CU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 49-VFBGA (5x5) | 49-VFBGA (5x5) | 49-VFBGA (5x5) | 49-VFBGA (5x5) | 49-VFBGA (5x5) |
| Flash Memory | 128 KB | 64 KB | 32 KB | 16 KB | 32 KB |
Diferensiator Kunci
- Largest flash capacity among the listed 49-VFBGA AVR XMEGA candidates (vsATXMEGA64D4-CU)
- Substantially larger code-storage margin than the 32 KB C4 option (vsATXMEGA32C4-CU)
- Eight kilobytes of SRAM for local buffering and control state (vsATXMEGA64D4-CU)
- Single established 49-ball footprint family simplifies PCB sourcing (vsATXMEGA128A4U)
Catatan Desain
Lay out the 49-ball VFBGA directly from the Microchip package drawing and land pattern. Place the recommended decoupling capacitors adjacent to the relevant supply balls, provide a low-impedance ground plane, and route sensitive analog or timing signals away from switching power stages. Because the balls are hidden after assembly, add X-ray or equivalent BGA inspection and use flying-probe or boundary-scan-compatible electrical verification. A solder bridge beneath the array cannot be detected reliably by visual inspection alone.
Design the supply around the 1.6 V to 3.6 V operating range and check the Microchip electrical-limit tables before selecting the operating frequency and brownout settings. Use local bulk and high-frequency decoupling at the device, and keep the power path short enough to limit voltage drop during current transients. Account for analog and digital load currents separately in the regulator budget, especially when the four timer/counter channels, both USARTs, and both two-wire interfaces are active concurrently.
The 34 I/O lines can carry high-speed timer, serial, and event-system signals, but their usable rise time depends on the external load and board topology. Avoid long stubs, maintain a continuous return path beneath signal routes, and keep clock and high-current outputs separated from analog inputs. For encoder or sensor inputs, use the timer capture resources and isolate sensitive traces from motor-drive switching nodes to preserve timing accuracy and reduce susceptibility to injected noise.
Do not substitute a smaller-flash XMEGA variant without rebuilding and testing the firmware. The ATXMEGA64D4-CU, ATXMEGA32D4-CU, and ATXMEGA16D4-CU can reduce available code and data storage, affecting bootloader placement, application images, and memory-mapped peripherals. Also avoid treating the -CU device as a QFN or TQFP footprint: its 49-ball VFBGA geometry and ball assignment must match the manufacturer drawing before new artwork is released.
Informasi Konformitas
The LCSC product listing identifies the ATXMEGA128D4-CU as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive-qualification statement was established from the available manufacturer and distributor information.