Produk (22.000+)

ATXMEGA192D3-MH - 32MHz 192KB AVR MCU | Microchip
ATXMEGA192D3-MH

ATXMEGA192D3-MH - 32MHz 192KB AVR MCU | Microchip

The Microchip ATXMEGA192D3-MH is a high-performance, low-power 8/16-bit AVR XMEGA D3 microcontroller with a 32 MHz clock, 192 KB of ISP Flash memory, and 16 KB of SRAM in a 64-pin QFN package measuring 9 mm by 9 mm. It operates from 1.6 V to 3.6 V and provides 50 general-purpose I/O lines for compact embedded control systems. An 8/16-bit microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces on one device. The ATXMEGA192D3 belongs to the AVR XMEGA family and uses a Harvard-style AVR architecture that supports both byte-oriented and 16-bit instruction processing. It sits above basic 8-bit AVR devices in processing performance, memory capacity, and event-handling capability while retaining the familiar AVR software ecosystem. The device combines 192 KB of ISP Flash, including an 8 KB boot-code section, with 2 KB of EEPROM and 16 KB of SRAM. Read-while-write Flash operation allows code execution during programming in supported regions. Its four-channel event system, programmable multilevel interrupt controller, and 16-bit real-time counter improve responsiveness in real-time control, measurement, and communication-oriented designs. Five flexible 16-bit timer/counter modules provide compare modes and PWM generation, while the peripheral set is intended to reduce the need for external control components. The 50 GPIO lines make the microcontroller suitable for systems requiring numerous digital inputs, outputs, and mixed signal interfaces without immediately exhausting package pin resources. ISP programming and supported debugging workflows simplify firmware development and production programming. Typical uses include industrial automation, building and access controls, sensor acquisition, compact motor control, connected equipment, and low-power embedded instruments. The 32 MHz operating speed is useful for event-driven control loops, while the 1.6 V to 3.6 V supply range supports low-voltage portable systems. Designers should verify peripheral availability, pin multiplexing, flash endurance, and analog performance against the manufacturer datasheet before finalizing a PCB layout. A key design consideration is the exposed-pad thermal and electrical interface of the 64-pin QFN package. Place the exposed pad according to the manufacturer land pattern, connect it to the appropriate ground plane, and provide uninterrupted copper for heat dissipation. Decoupling and signal-routing practices remain essential because the combination of high clock speed, dense GPIO assignment, and a 9 mm square footprint can constrain escape routing. This product page organizes the verified device identity, memory configuration, package information, and engineering context for faster component evaluation. It also distinguishes exact stock-keeping information from package and ordering variants, helping engineers identify the ATXMEGA192D3-MH without confusing it with similar XMEGA192 or XMEGA256 devices.

Permintaan RFG Kontak
ATXMEGA256A3-MH - 32MHz 256KB Flash MCU | Microchip
ATXMEGA256A3-MH

ATXMEGA256A3-MH - 32MHz 256KB Flash MCU | Microchip

The Microchip Technology ATXMEGA256A3-MH is a low-power 8/16-bit AVR XMEGA A3 microcontroller operating at up to 32 MHz with 256 KB of self-programming Flash memory in a 64-QFN 9 x 9 mm package. It provides 16 KB SRAM, 4 KB EEPROM, a 4-channel DMA controller, an 8-channel event system, dual 12-bit ADCs, and a 1.6 V to 3.6 V operating-voltage range. An 8/16-bit microcontroller is a compact semiconductor controller designed for embedded control, sensor acquisition, communications, and real-time peripheral management. The AVR enhanced RISC architecture belongs to the wider microcontroller hierarchy: AVR embedded controller, general-purpose processor, and semiconductor. Compared with many larger 32-bit systems, an XMEGA A3 device combines compact code execution with dedicated analog, timing, event, and DMA resources. The ATXMEGA256A3-MH's principal advantages include 256 KB of Flash for application code, a dedicated 8 KB boot-code section, and a 16 KB SRAM working area. Four DMA channels can transfer data between peripherals and memory, while the eight-channel event system can route events directly to peripherals without continuous processor intervention. These resources suit systems in which deterministic peripheral timing and reduced CPU overhead are important. Its dual 12-bit ADC supports analog measurements, while the AVR architecture supports both 8-bit and 16-bit instruction operations. The manufacturer describes the family as capable of approaching 1 MIPS per MHz through single-cycle execution. The ATXMEGA256A3-MH therefore balances processing throughput, memory capacity, and peripheral integration without requiring an external coprocessor for many embedded-control workloads. Typical uses include industrial sensor controllers, communication equipment, data-acquisition systems, compact motor controllers, low-power embedded instruments, and USB-enabled control nodes. Its DMA and event-system resources are particularly useful for simultaneous communication and sampling, while the large Flash capacity supports protocol stacks, bootloaders, and application firmware in one device. PCB design should preserve short analog and digital return paths, place decoupling capacitors close to the supply pins, and follow the manufacturer pin-description table for the 64-QFN footprint. Verify operating voltage, clock configuration, peripheral pin multiplexing, programming interfaces, and exposed-pad assembly requirements against the manufacturer datasheet before releasing the board layout. This page combines the ATXMEGA256A3-MH technical specifications, package and memory details, comparison data, application guidance, and practical design considerations to support faster component selection and board-design planning.

Permintaan RFG Kontak
ATXMEGA256A3BU-AU - 256KB Flash 32MHz AVR XMEGA A3BU MCU | Microchip
ATXMEGA256A3BU-AU

ATXMEGA256A3BU-AU - 256KB Flash 32MHz AVR XMEGA A3BU MCU | Microchip

The Microchip Technology ATXMEGA256A3BU-AU is a low-power, high-performance 8/16-bit AVR XMEGA A3BU microcontroller delivering 32 MHz CPU throughput with 256 KB in-system self-programmable Flash, 16 KB SRAM, and 4 KB EEPROM, housed in a 64-pin TQFP (14x14 mm) package. It targets embedded designs that require deterministic real-time performance, rich analog integration, and battery-backed operation. What is an XMEGA microcontroller? An XMEGA (pronounced "mega") is a family of 8/16-bit microcontrollers based on Atmel's enhanced AVR RISC architecture. It executes most instructions in a single clock cycle, achieving throughput approaching 1 MIPS per MHz. In the taxonomy, XMEGA sits between the ATmega 8-bit family and 32-bit ARM Cortex-M devices - delivering higher peripheral integration than ATmega while remaining easier to program than 32-bit MCUs, with deterministic interrupt latency suited for real-time control. Key features include dual 12-bit ADCs (2 Msps with optional PGA), up to 7 USART/UART interfaces, 4-channel DMA controller, 8-channel event system for inter-peripheral signalling, hardware crypto engine (AES/DES), and a unique 32-bit Real-Time Counter with separate 32.768 kHz oscillator. The 64-pin TQFP exposes full USB 2.0 full-speed device support plus 4-wire touch interface and a battery-backup domain with separate VBAT pin. The "B" variant in A3BU adds this battery-backed RTC, which the plain A3U lacks. The A3BU is built on a high-performance CMOS process with a multi-channel event system that lets peripherals trigger each other without CPU intervention, offloading DMA-driven data movement. An integrated cryptographic accelerator performs AES-128 and DES/3DES in hardware, while the peripheral event system supports capacitive touch measurement via the on-chip PTC (Peripheral Touch Controller). The 32-bit RTC plus separate low-power oscillator makes the part especially attractive for metering, security, and battery-backed data logging. Typical applications include industrial automation controllers, smart energy metering with battery backup, USB-connected HID/data acquisition peripherals, capacitive touch HMI panels, building automation gateways, and portable medical instrumentation. The combination of dual 12-bit ADC, hardware crypto, and battery-backed RTC also fits secure IoT edge nodes. Design consideration: ensure the 32.768 kHz crystal and load capacitors meet the datasheet's ESR and load-capacitance specifications for reliable RTC operation, especially across temperature. Also, reserve the VBAT pin for a coin-cell or super-capacitor backup if non-volatile RTC retention is required. This page synthesizes distributor pricing, drop-in alternatives, and engineering design notes not aggregated on the manufacturer datasheet, giving procurement and embedded engineers a single source for cross-reference and design validation.

Permintaan RFG Kontak
ATXMEGA256A3BU-MH - 256KB Flash 32MHz AVR XMEGA MCU | Microchip
ATXMEGA256A3BU-MH

ATXMEGA256A3BU-MH - 256KB Flash 32MHz AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA256A3BU-MH is a low-power, high-performance 8/16-bit AVR XMEGA A3BU microcontroller featuring 256 KB self-programming Flash, 16 KB SRAM, and 4 KB EEPROM, operating up to 32 MHz from a 2.7V to 3.6V supply, housed in a 64-pin QFN (9x9 mm) package. It integrates a 4-channel DMA controller, 8-channel event system, dual 12-bit ADC, and a 32-bit Real-Time Counter with Battery Backup System (VBAT) for RTC retention. An AVR XMEGA microcontroller is a member of Microchip's 8/16-bit RISC MCU family that extends the classic AVR core with a wider 16-bit instruction path, hardware DMA, an event system for peripheral-to-peripheral signaling without CPU intervention, and rich analog peripherals. XMEGA parts sit between the 8-bit ATmega family and 32-bit ARM Cortex-M parts, making them well suited to mixed-signal embedded designs that need deterministic I/O timing and low active power. Key features of the ATXMEGA256A3BU include 256 KB Flash with an 8 KB boot code section, 16 KB SRAM, 4 KB EEPROM, 34 programmable I/O lines, dual 12-bit ADC, two 12-bit DAC channels, multiple USART/SPI/TWI interfaces, AES/DES crypto engine, and an RTC subsystem with VBAT pin (PF5) that keeps the 32-bit RTC running during main-battery loss. The 32 MHz peak core speed with a single-cycle 16-bit ALU delivers roughly 32 MIPS throughput while consuming only a few mA in active mode. The A3BU silicon uses Microchip's picoPower technology with multiple sleep modes down to sub-microamp standby, plus an event system that lets peripherals trigger each other so the CPU can stay asleep longer. The Battery Backup System preserves RTC state across main-power failures by switching the RTC supply onto VBAT, which is a key feature absent from the otherwise similar ATxmega256A3U. Typical applications include industrial sensor hubs, smart metering, building automation, low-power wireless sensor nodes paired with an external radio, motor control, USB device/embedded hosts, and battery-backed data loggers. The 32-bit RTC plus VBAT makes it a strong fit for any design that must keep wall-clock time through power cycles. When designing with this MCU, route VBAT through a backup supercap or coin cell, decouple the main VCC with 100 nF plus 4.7 µF bulk caps adjacent to each supply pin, and reserve a dedicated 6-pin PDI header for in-system programming because the QFN package cannot be socketed on most production boards. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
ATXMEGA256A3U-AN - 32MHz 256KB Flash 8/16-bit AVR MCU | Microchip
ATXMEGA256A3U-AN

ATXMEGA256A3U-AN - 32MHz 256KB Flash 8/16-bit AVR MCU | Microchip

The Microchip Technology ATXMEGA256A3U-AN is a low-power, high-performance 8/16-bit AVR XMEGA A3U microcontroller running at up to 32 MHz with 256 KB self-programming Flash program memory, 16 KB SRAM and 4 KB EEPROM, housed in a 64-pin TQFP (14x14 mm) package rated for 105 °C operation. The device delivers up to 32 MIPS throughput and integrates a 4-channel DMA controller, an 8-channel event system, a cryptographic AES/DES engine on the A3U family, and full-speed USB 2.0 device support, making it a peripheral-rich member of the Atmel AVR enhanced RISC architecture. Background Knowledge: An 8/16-bit AVR XMEGA microcontroller is a member of the RISC microcontroller family, sitting in the hierarchy 8-bit MCU -> AVR core -> XMEGA family -> A3U series -> 64-pin TQFP class. It executes most instructions in a single clock cycle, providing close to 1 MIPS per MHz, and combines deterministic interrupt response with rich analog and digital peripherals for embedded control. Key features include 256 KB Flash with 8 KB boot section, 4 KB EEPROM endurance up to 100,000 cycles, 16 KB SRAM, an internal 32 MHz calibrated oscillator, multiple USART/SPI/TWI interfaces, and a 12-bit ADC with up to 2 MSPS sampling. The A3U suffix designates the USB-equipped sub-family with hardware AES and DES crypto engines. The 1.6 V to 3.6 V supply range supports battery and industrial 3.3 V rails, while sleep current under 1 µA with RTC running enables energy-harvesting and portable designs. Typical applications include USB peripherals, building and industrial automation, motor control, sensor hubs, and human-machine interface (HMI) panels. The integrated full-speed USB 2.0 device interface is widely used for HID, CDC, and vendor-class peripherals without an external transceiver. Hardware AES/DES acceleration offloads secure communication tasks from the CPU, while the 12-bit ADC and high-resolution timers simplify BLDC and stepper motor control loops. Designers should size decoupling per 64-pin TQFP power pins and follow the Atmel AVR1003 application note for USB hardware design. Use the Atmel AVR Studio / Microchip Studio toolchain with the AVR Dragon or JTAGICE3 for in-system debug. The XMEGA A3U datasheet and AVR1020 migration note are the authoritative references for peripheral mapping and migration from earlier A3 (non-U) parts.

Permintaan RFG Kontak
ATXMEGA256A3U-AU - 256KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA256A3U-AU

ATXMEGA256A3U-AU - 256KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA256A3U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A3U microcontroller delivering up to 32 MIPS throughput at 32 MHz, integrating 256 KB of self-programming Flash program memory plus an 8 KB boot code section in a 64-pin TQFP (14x14 mm) package. It is part of the AVR enhanced RISC architecture family with single-cycle instruction execution. An 8/16-bit microcontroller (MCU) is a programmable system-on-a-chip that combines a CPU, Flash program memory, SRAM, EEPROM, and a rich set of peripherals on a single die. MCUs are the highest-volume category of integrated circuits and serve as the digital core of nearly every embedded product - from battery-powered IoT nodes to industrial motor drives - occupying the middle of the silicon hierarchy between simple discrete logic and full microprocessors. Key features include 16 KB SRAM, 4 KB EEPROM, a 4-channel DMA controller, an 8-channel event system, and 34 programmable I/O lines. The device operates from a 2.7V to 3.6V supply, supports LVTTL/LVCMOS-compatible I/O, and includes multiple communication interfaces (USART, SPI, TWI) plus a 12-channel 12-bit ADC and analog comparators. The A3U variant adds a USB 2.0 Full-Speed device interface absent from the non-U A3 series. The ATXMEGA256A3U uses a Harvard-architecture AVR CPU with a 3-stage pipeline and hardware multiplier, achieving 1 MIPS per MHz. The peripheral event system lets peripherals trigger one another without CPU intervention, freeing the core for application code. The 4-channel DMA controller can move data between peripherals and memory autonomously, further reducing CPU load for streaming or signal-processing tasks. Typical applications include building automation, industrial control, low-power IoT sensor nodes, motor control, metering, USB peripherals, and human-machine interfaces (HMI) with LCD segments. The wide peripheral set and large Flash make it well suited to data logging, LCD-keypad control panels, and protocol bridges that previously required external logic. When designing with this MCU, allocate adequate decoupling (typically 100 nF plus 10 uF bulk) close to each VCC pin, and follow the XMEGA AU manual guidance for PDI programming interface routing. The 64-pin TQFP footprint is shared with the rest of the ATxmega A3U family, allowing easy migration to the 192A3U, 128A3U, or 64A3U derivatives by code recompilation.

Permintaan RFG Kontak
ATXMEGA256C3-MH - 256KB Flash 32MHz XMEGA C3 MCU | Microchip
ATXMEGA256C3-MH

ATXMEGA256C3-MH - 256KB Flash 32MHz XMEGA C3 MCU | Microchip

The Microchip Technology ATXMEGA256C3-MH is a high-performance, low-power 8/16-bit AVR XMEGA C3 microcontroller featuring 256 KB in-system programmable Flash (with 8 KB boot code section and read-while-write capability), 4 KB EEPROM, 16 KB SRAM, and a 32 MHz CPU core, housed in a 64-pin QFN (9x9 mm) package. What is an AVR XMEGA microcontroller? The XMEGA family is a modernized successor to the classic 8-bit AVR architecture, combining a 16-bit instruction set with an 8-bit datapath (often described as 8/16-bit). Within the broader taxonomy it sits as: microcontroller -> embedded MCU -> 8/16-bit MCU -> AVR -> AVR XMEGA -> XMEGA C3 series. The C3 sub-series adds high-speed analog and a four-channel event system, positioning it above entry-level ATmega parts in both peripheral count and computational throughput. Key differentiating specifications include 50 general-purpose I/O lines, five 16-bit timer/counters with capture/compare/PWM, a 16-bit real-time counter, a four-channel event system, a programmable multi-level interrupt controller, USB Device and AES/DES crypto engine. The 32 MHz core delivers 32 MIPS with single-cycle execution, while peripheral DMA on 4 channels reduces CPU load for data movement. The architecture integrates an on-chip programmable gain amplifier (PGA), a 12-bit 2 MSPS ADC, a 12-bit 1 MSPS DAC, and multiple communication interfaces including USART, SPI, TWI (I2C), and full-speed USB. The 1.6 V to 3.6 V wide operating voltage and five software-selectable sleep modes with sub-microamp standby current make it well suited to battery-aware designs that need to wake on event. Typical applications include industrial control panels, building automation (HVAC, lighting, metering), USB peripherals (HID, CDC, custom class), motor control boards, handheld battery-powered instruments, factory automation nodes, and medical/clinical devices. The combination of large Flash, integrated crypto, and DMA makes it a strong fit for networked sensor hubs and secure IoT edge nodes. Designers should note that pin count and footprint drive PCB layout decisions. The 64-QFN variant is the highest-density option in the C3 family. Power estimation should include peripheral current draw and clock tree contributions, especially when high-speed peripherals are enabled. This page synthesizes distributor pricing, drop-in alternatives in the same 64-QFN footprint, and practical design notes not assembled on the manufacturer datasheet or distributor catalog pages.

Permintaan RFG Kontak
ATXMEGA256D3-AU - 32MHz 256KB Flash AVR MCU | Microchip
ATXMEGA256D3-AU

ATXMEGA256D3-AU - 32MHz 256KB Flash AVR MCU | Microchip

The Microchip ATXMEGA256D3-AU is a low-power 8/16-bit AVR XMEGA D3 microcontroller combining a 32 MHz clock, 256 KB of ISP Flash memory, 4 KB of EEPROM, and 16 KB of SRAM in a 64-pin TQFP package. The 64-TQFP package measures 14 x 14 mm and provides 50 general-purpose I/O lines for connected control and data-acquisition systems. An 8 KB boot-code section and read-while-write Flash operation support in-system firmware updates. An 8/16-bit microcontroller is a compact embedded-processing device that executes instructions from internal Flash memory while using dedicated peripherals to interact with sensors, communication circuits, and actuators. Within the component hierarchy, the ATXMEGA256D3-AU is an AVR XMEGA microcontroller, an enhanced RISC processor family designed to combine deterministic control, event-driven hardware handling, and low-power operation in a single device. The XMEGA D3 feature set includes a four-channel event system, a programmable multi-level interrupt controller, a 16-bit real-time counter, and five flexible 16-bit timer/counter blocks with compare modes and PWM support. These resources allow software to offload periodic timing, edge detection, and signal routing to dedicated hardware, reducing interrupt-handling overhead in motor, lighting, and industrial control systems. The device operates from a 2.7 V to 3.6 V supply and reaches a maximum clock rate of 32 MHz. Its memory architecture is organized for embedded firmware and parameter storage: 256 KB of Flash holds application code and the 8 KB boot section, 4 KB of EEPROM preserves configuration values across power cycles, and 16 KB of SRAM supports stack, buffers, and real-time state. The 34-port figure reported for the device reflects the usable port resources associated with the 50 general-purpose I/O lines and package implementation. Typical applications include industrial automation modules, data loggers, motor and pump controllers, LED lighting systems, USB-connected peripherals, and compact sensor-hub products. The 50 I/O lines permit multiple digital interfaces to coexist on one board, while the event system and five timer/counter blocks support deterministic periodic control without excessive firmware polling. When laying out a board, route the clock, programming interface, and sensitive analog inputs according to the pin-description table in the manufacturer datasheet. Decoupling requirements and external component recommendations should also follow that document. Confirm the operating voltage, clock source, programming method, and boot configuration before releasing a PCB layout, because incorrect peripheral multiplexing or startup settings can prevent a fully populated board from operating as intended. This page combines the manufacturer's XMEGA D3 specifications with a package-focused comparison, practical design guidance, drop-in candidate evaluation, and application-specific engineering context. It is intended to accelerate component selection and board planning beyond the basic distributor specification table.

Permintaan RFG Kontak
ATXMEGA256D3-MH - 32MHz AVR MCU with 256KB Flash | Microchip
ATXMEGA256D3-MH

ATXMEGA256D3-MH - 32MHz AVR MCU with 256KB Flash | Microchip

The Microchip Technology ATXMEGA256D3-MH is a high-performance, low-power 8/16-bit AVR XMEGA D3 microcontroller operating at up to 32 MHz, with 256 KB of ISP Flash memory, 4 KB of EEPROM, and 16 KB of SRAM. It is packaged in a 64-pin VQFN with an exposed thermal pad and a 9 x 9 mm body. The operating voltage range is 1.6 V to 3.6 V, while the industrial temperature range is -40°C to +85°C. An 8/16-bit AVR microcontroller combines a Harvard-architecture processor with embedded flash, EEPROM, SRAM, and programmable peripherals in one integrated device. The XMEGA D3 family extends the familiar AVR ecosystem with a four-channel event system, programmable multi-level interrupt handling, and high-resolution peripherals for embedded control, communications, and signal-processing applications. Its dual-controller architecture supports deterministic task separation and efficient real-time event handling. Key features include 256 KB of read-while-write ISP Flash with an 8 KB boot-code section, 4 KB of EEPROM, 16 KB of SRAM, and operation up to 32 MHz. The device provides 16-channel 12-bit ADC capability, advanced timers, communication interfaces, and flexible pin multiplexing. These resources allow the MCU to consolidate functions that might otherwise require several discrete analog and digital components. The ATxmega256D3 platform combines a 32 MHz core, event-system routing, and programmable interrupt priorities for responsive embedded designs. Read-while-write Flash allows firmware data to remain accessible during programming operations, while the boot-code section supports controlled startup and update workflows. The 1.6 V to 3.6 V operating range is suitable for low-voltage industrial, consumer, and communications equipment operating from regulated 3.3 V rails or compatible lower-voltage sources. Typical applications include industrial control and factory automation, communication nodes, sensor acquisition systems, compact motor controllers, measurement instruments, and low-power embedded products. Its combination of memory, analog conversion, timing peripherals, and event-driven control makes it particularly useful when board space and deterministic response are important. PCB design should preserve the exposed-pad thermal and electrical requirements of the VQFN. Place input and output decoupling capacitors close to their associated supply pins, provide a low-impedance ground plane, and follow the manufacturer pin-assignment table when assigning multiplexed I/O functions. Confirm boot, programming, and clock options against the device documentation before releasing production firmware. This product page combines manufacturer specifications, package and ordering details, supported programming information, comparison guidance, and practical implementation notes to support component selection, schematic review, PCB planning, and sourcing decisions.

Permintaan RFG Kontak
ATXMEGA32A4-AN 32MHz 32KB Flash Microcontroller | Microchip
ATXMEGA32A4-AN

ATXMEGA32A4-AN 32MHz 32KB Flash Microcontroller | Microchip

The Microchip ATXMEGA32A4-AN is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a maximum clock speed of 32 MHz, 32 KB of self-programming Flash memory, 4 KB of boot-code section, 4 KB of SRAM, and 1 KB of EEPROM. According to the manufacturer product page, the device also provides an external bus interface, a four-channel DMA controller, an eight-channel event system, and up to 32 general-purpose I/O lines when configured for its maximum operating frequency. An 8/16-bit MCU is a microcontroller that combines a compact processor core, program memory, data memory, and peripherals in one integrated device. The XMEGA A4 family extends the AVR enhanced RISC architecture with a 16-bit instruction set, high-resolution timers, flexible serial interfaces, and event-driven hardware. This makes the ATXMEGA32A4 suitable for control systems that need more peripheral flexibility than a basic 8-bit MCU without moving to a more complex application processor. Key features include In-System Programmable Flash with Read-While-Write operation, a four-channel DMA controller, an eight-channel Event System, a programmable multi-level interrupt controller, 34 general-purpose I/O lines, a 16-bit Real Time Counter, five flexible 16-bit Timer/Counters with compare and PWM modes, five USARTs, and two Two-Wire Interfaces. The combination of DMA and the Event System allows data movement and peripheral actions to proceed with limited CPU intervention. The device is designed for low-power embedded designs operating from a 2.7 V to 3.6 V supply. Its peripherals support applications that mix serial communications, real-time counting, PWM generation, and external memory or peripheral interfacing. The on-chip boot section and self-programming Flash also support firmware update workflows where supported by the application architecture. Typical uses include industrial control modules, data acquisition front ends, communications equipment, motor and power-system controllers, and compact embedded instruments. Because the ATXMEGA32A4-AN combines an event system with DMA, it is particularly useful when several timing-sensitive tasks must be coordinated while leaving the CPU available for control algorithms. Before assigning PCB tracks or defining a footprint, confirm the exact package variant and pin assignments in the manufacturer datasheet and the order code documentation. Use the manufacturer pin-description table for the selected package rather than relying on generic XMEGA A4 diagrams, because the 32-pin and 44-pin family members do not expose the same peripheral mix.

Permintaan RFG Kontak
ATXMEGA32A4-AU - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU
ATXMEGA32A4-AU

ATXMEGA32A4-AU - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU

The Microchip Technology ATXMEGA32A4-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with 32 KB self-programming Flash, 4 KB SRAM, 1 KB EEPROM, and a 4 KB boot code section, packaged in a 44-pin TQFP (10x10 mm). It runs at up to 32 MHz delivering 32 MIPS throughput, with 34 general-purpose I/O lines, a 4-channel DMA controller, an 8-channel event system, and a programmable multi-level interrupt controller. Operating voltage range is 1.6 V to 3.6 V per the manufacturer datasheet. An AVR XMEGA microcontroller is an advanced 8/16-bit RISC architecture MCU that extends the classic AVR core with a richer peripheral set, DMA-driven I/O, an event system for inter-peripheral signaling, and a more capable interrupt controller, while keeping the AVR instruction set and toolchain compatibility. XMEGA sits above classic ATmega in the Microchip (formerly Atmel) AVR taxonomy, between ATmega and the SAM Cortex-M families in terms of performance and peripheral depth. It targets low-power embedded designs that need deterministic I/O without leaving the AVR ecosystem. Key features include 32 KB in-system programmable Flash with read-while-write support, 1 KB internal EEPROM for non-volatile data, five flexible 16-bit Timer/Counters with compare and PWM modes, two TWI (I2C-compatible) interfaces, five USARTs, two SPI ports, a 16-bit Real-Time Counter (RTC), a 12-channel 12-bit ADC, and AES/DES crypto accelerators. The DMA controller and event system offload repetitive I/O from the CPU, enabling efficient sensor and communication pipelines. The integrated bandgap reference and on-chip temperature sensor simplify analog designs. Architecturally, the A4 series uses the XMEGA core with single-cycle ALU operations, hardware multiplier, and a peripheral event system that allows peripherals to trigger each other without CPU intervention. The result is deterministic low-latency I/O at very low active currents, making the A4 family well suited to battery-powered measurement, sensor hubs, and human-interface products. Typical applications include industrial sensor nodes, smart metering, building automation controllers, low-power wireless sensor hubs (paired with an external radio), USB/HID peripherals, motor control edge nodes, and consumer human-interface devices. Choose the ATXMEGA32A4-AU when you need AVR toolchain continuity with XMEGA-grade peripherals in a 44-pin TQFP. Designers should plan a stable 1.6 V to 3.6 V rail with sufficient decoupling near the AVDD pins, route the event system lines carefully to avoid noise coupling into ADC inputs, and verify the boundary scan / PDI programming interface is accessible for in-system firmware updates. Selecting the A4 family preserves AVR toolchain investment while adding modern peripherals. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
ATXMEGA32A4-AUR - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU (Tape & Reel)
ATXMEGA32A4-AUR

ATXMEGA32A4-AUR - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU (Tape & Reel)

The Microchip Technology ATXMEGA32A4-AUR is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with 32 KB self-programming Flash, 4 KB SRAM, 1 KB EEPROM, and a 4 KB boot code section, packaged in a 44-pin TQFP (10x10 mm). It runs at up to 32 MHz delivering 32 MIPS throughput, with 34 general-purpose I/O lines, a 4-channel DMA controller, an 8-channel event system, and a programmable multi-level interrupt controller. Operating voltage range is 1.6 V to 3.6 V per the manufacturer datasheet. An AVR XMEGA microcontroller is an advanced 8/16-bit RISC architecture MCU that extends the classic AVR core with a richer peripheral set, DMA-driven I/O, an event system for inter-peripheral signaling, and a more capable interrupt controller, while keeping the AVR instruction set and toolchain compatibility. XMEGA sits above classic ATmega in the Microchip (formerly Atmel) AVR taxonomy, between ATmega and the SAM Cortex-M families in terms of performance and peripheral depth. It targets low-power embedded designs that need deterministic I/O without leaving the AVR ecosystem. Key features include 32 KB in-system programmable Flash with read-while-write support, 1 KB internal EEPROM for non-volatile data, five flexible 16-bit Timer/Counters with compare and PWM modes, two TWI (I2C-compatible) interfaces, five USARTs, two SPI ports, a 16-bit Real-Time Counter (RTC), a 12-channel 12-bit ADC, and AES/DES crypto accelerators. The DMA controller and event system offload repetitive I/O from the CPU, enabling efficient sensor and communication pipelines. The integrated bandgap reference and on-chip temperature sensor simplify analog designs. Architecturally, the A4 series uses the XMEGA core with single-cycle ALU operations, hardware multiplier, and a peripheral event system that allows peripherals to trigger each other without CPU intervention. The result is deterministic low-latency I/O at very low active currents, making the A4 family well suited to battery-powered measurement, sensor hubs, and human-interface products. Typical applications include industrial sensor nodes, smart metering, building automation controllers, low-power wireless sensor hubs (paired with an external radio), USB/HID peripherals, motor control edge nodes, and consumer human-interface devices. Choose the ATXMEGA32A4-AUR when you need AVR toolchain continuity with XMEGA-grade peripherals in a 44-pin TQFP. Designers should plan a stable 1.6 V to 3.6 V rail with sufficient decoupling near the AVDD pins, route the event system lines carefully to avoid noise coupling into ADC inputs, and verify the boundary scan / PDI programming interface is accessible for in-system firmware updates. Selecting the A4 family preserves AVR toolchain investment while adding modern peripherals. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
ATXMEGA32A4-CU - 32MHz 32KB AVR Microcontroller | Microchip
ATXMEGA32A4-CU

ATXMEGA32A4-CU - 32MHz 32KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA32A4-CU is an 8/16-bit AVR XMEGA A4 microcontroller operating at 32 MHz, with 32 KB of self-programming Flash, 4 KB of SRAM, and a 49-VFBGA 5 x 5 mm package. Its operating supply range is 1.6 V to 3.6 V according to the Mouser product listing. The device combines an AVR RISC processor with a hardware multiplier and integrated high-speed peripherals for compact embedded-control designs. An 8/16-bit microcontroller is a programmable semiconductor that executes firmware, reads sensor inputs, controls actuators, and manages communications in an embedded system. The ATxmega family belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductor components. Unlike a general-purpose application processor, this device emphasizes deterministic peripheral operation, event handling, direct memory access, and low-power embedded control while retaining familiar AVR software development. The ATXMEGA32A4-CU provides 32 KB of self-programming Flash program memory, including a 4 KB boot-code section, together with 4 KB SRAM and 1 KB EEPROM. Its integrated peripherals include a four-channel DMA controller, an eight-channel event system, an external bus interface, and communication resources listed for the family as five USARTs and two Two-Wire Interfaces. The 34 I/O pins provide connections for sensors, actuators, human-interface inputs, and external buses. The XMEGA architecture uses an event system to connect peripherals without requiring continuous CPU polling. This can reduce software overhead in designs that must respond to timer, communication, or external-signal events. The four-channel DMA controller is useful for transferring data between memory and peripherals, while self-programming Flash supports firmware maintenance and bootloader-based updates. Operating at 32 MHz provides additional processing headroom for protocol handling and control-loop calculations. Typical uses include industrial automation modules, compact sensor nodes, data-logging instruments, communication equipment, and low-power embedded controllers. Its 49-VFBGA package is particularly appropriate for space-constrained products where a reduced package area is valuable. Board assembly requires suitable BGA manufacturing and inspection capability, so designers must account for package geometry, solder-mask design, thermal management, and assembly yield during volume production. A key design consideration is that the small 5 x 5 mm BGA is not a simple through-hole or two-row-package substitution. Existing PCB layouts must match the exact 49-ball footprint, ball assignments, exposed-pad requirements, and manufacturer land pattern. Firmware should also be validated at the intended 1.6 V to 3.6 V supply conditions because timing and peripheral performance can vary with voltage and frequency. This page combines verified manufacturer and distributor specifications with package, sourcing, application, and replacement guidance. It also distinguishes genuine same-footprint alternatives from related XMEGA devices that have different memory sizes or order codes, helping engineers avoid treating functional similarity as drop-in compatibility.

Permintaan RFG Kontak
ATXMEGA32A4-MH - 32MHz AVR Microcontroller | Microchip Technology
ATXMEGA32A4-MH

ATXMEGA32A4-MH - 32MHz AVR Microcontroller | Microchip Technology

Microchip Technology ATXMEGA32A4-MH is an 8/16-bit AVR XMEGA A4 microcontroller operating up to 32 MHz with 32 KB of self-programming Flash memory and a 44-VQFN 7 x 7 mm package. The device includes 4 KB of boot-code section space, 4 KB SRAM, 1 KB EEPROM, a four-channel DMA controller, an eight-channel event system, and an external bus interface. Its operating-voltage information spans 1.6 V to 3.6 V, while one distributor specification lists a 2.7 V to 3.6 V supply range for this package. An 8/16-bit AVR microcontroller is a compact embedded-processing component within the microcontroller, semiconductor, and embedded-systems hierarchy. The ATXMEGA family combines a Harvard-style RISC core, memory, timers, communication peripherals, and general-purpose I/O in one package. Compared with larger 32-bit microcontrollers, it provides a focused platform for real-time control, data acquisition, human-interface equipment, and low-power embedded products where 32 KB Flash is sufficient and deterministic peripheral operation is valuable. The principal features of the ATXMEGA32A4 include a 32 MHz maximum clock, 32 KB Flash organized as 16K x 16, 4 KB SRAM, 1 KB EEPROM, and 34 I/O ports. Peripherals include a four-channel DMA controller, an eight-channel event system, and an external bus interface. The 44-VQFN package provides a compact surface-mount solution for space-constrained PCB layouts, although its fine pitch requires careful assembly and land-pattern design. At the architectural level, the AVR enhanced RISC core executes instructions in a single clock cycle and can approach 1 MIPS per MHz. The DMA controller can transfer data without occupying the CPU for each peripheral transaction, while the event system routes peripheral signals between timer, comparator, and communication resources. This combination supports responsive control loops and coordinated sampling in industrial, communication, and consumer equipment. Typical uses include industrial monitoring, building-control interfaces, sensor hubs, programmable logic controllers, data loggers, and compact communication equipment. The combination of 34 I/O ports, four DMA channels, and an event system is particularly useful when multiple timers, counters, or serial peripherals must operate in a coordinated manner. A system requiring more Flash, SRAM, or peripherals may require a larger ATxmega model rather than this 32 KB A4 device. Designers should verify the exact pin functions, alternate-function mappings, clock requirements, and power behavior against the manufacturer datasheet before layout release. The 44-VQFN footprint requires a conservative solder mask and paste pattern, and unused pins must be connected according to the device guidance. Supply-voltage requirements should also be checked against the specific clock, peripheral, and operating-temperature conditions used by the product. This page consolidates verified distributor inventory, manufacturer feature information, package details, commercial pricing, application guidance, and design considerations. It also distinguishes genuine same-footprint alternatives from related devices that use different packages or materially different memory configurations, helping engineers avoid a replacement that cannot be soldered onto the existing PCB.

Permintaan RFG Kontak
ATXMEGA32A4-MHR - 32MHz AVR Microcontroller | Microchip Technology (Tape & Reel)
ATXMEGA32A4-MHR

ATXMEGA32A4-MHR - 32MHz AVR Microcontroller | Microchip Technology (Tape & Reel)

Microchip Technology ATXMEGA32A4-MHR is an 8/16-bit AVR XMEGA A4 microcontroller operating up to 32 MHz with 32 KB of self-programming Flash memory and a 44-VQFN 7 x 7 mm package. The device includes 4 KB of boot-code section space, 4 KB SRAM, 1 KB EEPROM, a four-channel DMA controller, an eight-channel event system, and an external bus interface. Its operating-voltage information spans 1.6 V to 3.6 V, while one distributor specification lists a 2.7 V to 3.6 V supply range for this package. An 8/16-bit AVR microcontroller is a compact embedded-processing component within the microcontroller, semiconductor, and embedded-systems hierarchy. The ATXMEGA family combines a Harvard-style RISC core, memory, timers, communication peripherals, and general-purpose I/O in one package. Compared with larger 32-bit microcontrollers, it provides a focused platform for real-time control, data acquisition, human-interface equipment, and low-power embedded products where 32 KB Flash is sufficient and deterministic peripheral operation is valuable. The principal features of the ATXMEGA32A4 include a 32 MHz maximum clock, 32 KB Flash organized as 16K x 16, 4 KB SRAM, 1 KB EEPROM, and 34 I/O ports. Peripherals include a four-channel DMA controller, an eight-channel event system, and an external bus interface. The 44-VQFN package provides a compact surface-mount solution for space-constrained PCB layouts, although its fine pitch requires careful assembly and land-pattern design. At the architectural level, the AVR enhanced RISC core executes instructions in a single clock cycle and can approach 1 MIPS per MHz. The DMA controller can transfer data without occupying the CPU for each peripheral transaction, while the event system routes peripheral signals between timer, comparator, and communication resources. This combination supports responsive control loops and coordinated sampling in industrial, communication, and consumer equipment. Typical uses include industrial monitoring, building-control interfaces, sensor hubs, programmable logic controllers, data loggers, and compact communication equipment. The combination of 34 I/O ports, four DMA channels, and an event system is particularly useful when multiple timers, counters, or serial peripherals must operate in a coordinated manner. A system requiring more Flash, SRAM, or peripherals may require a larger ATxmega model rather than this 32 KB A4 device. Designers should verify the exact pin functions, alternate-function mappings, clock requirements, and power behavior against the manufacturer datasheet before layout release. The 44-VQFN footprint requires a conservative solder mask and paste pattern, and unused pins must be connected according to the device guidance. Supply-voltage requirements should also be checked against the specific clock, peripheral, and operating-temperature conditions used by the product. This page consolidates verified distributor inventory, manufacturer feature information, package details, commercial pricing, application guidance, and design considerations. It also distinguishes genuine same-footprint alternatives from related devices that use different packages or materially different memory configurations, helping engineers avoid a replacement that cannot be soldered onto the existing PCB.

Permintaan RFG Kontak
ATXMEGA32A4U-AN - 32MHz AVR XMEGA MCU | Microchip Technology
ATXMEGA32A4U-AN

ATXMEGA32A4U-AN - 32MHz AVR XMEGA MCU | Microchip Technology

The Microchip Technology ATXMEGA32A4U-AN is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller operating at up to 32 MHz, with 32 KB of self-programming Flash memory, 4 KB of SRAM, and 1 KB of EEPROM in a 44-pin TQFP package. It supports a 1.6 V to 3.6 V supply range and is specified for operation up to 105°C. The device is positioned for embedded applications requiring substantial peripheral integration, deterministic real-time control, and low-power operation in a compact surface-mount package. An AVR XMEGA microcontroller combines an enhanced RISC core with an advanced event system and hardware peripherals designed to reduce interrupt overhead. The XMEGA family sits within the broader 8/16-bit MCU hierarchy, combining flash-programmable firmware storage, SRAM, EEPROM, timers, serial interfaces, analog conversion, and direct GPIO control. Compared with simpler 8-bit AVR devices, the ATXMEGA32A4U-AN provides four-channel DMA, an eight-channel event system, a programmable multi-level interrupt controller, and extensive timer resources for responsive control systems. Key features include 34 general-purpose I/O lines, five flexible 16-bit Timer/Counters with compare and PWM modes, five USART modules, a 16-bit Real Time Counter, two Two-Wire Interfaces, two Serial Peripheral Interfaces, and up to 32 analog input channels. Its 32 KB Flash includes a dedicated 4 KB boot-code section for firmware update or startup routines. The internal 4 KB SRAM supports event-driven data movement without requiring every transfer to pass through the CPU. The four-channel DMA controller can transfer data among memory and peripherals while the CPU performs other tasks. Combined with the eight-channel event system, this architecture is useful when deterministic timing is required without frequent polling. The programmable multi-level interrupt controller supports prioritized event handling, while the RTC and five 16-bit timers provide dedicated timing resources for control, communication, and periodic measurement functions. Typical uses include industrial control modules, data acquisition units, communications equipment, low-power sensor nodes, motor-control peripherals, and compact embedded gateways. The 44-TQFP package provides more I/O than a small leadless MCU, making it practical for designs that need several serial interfaces alongside sensor and actuator connections. Its 3.6 V maximum listed operating voltage also supports integration with common low-voltage industrial and embedded systems. PCB design should place decoupling capacitors close to each VDD connection, preserve a continuous ground plane, and route sensitive analog inputs away from fast-switching nodes. Firmware should use the event system and DMA where timing paths overlap, while the boot section should contain only code required during startup. The 44-TQFP footprint also demands careful assembly planning because its fine lead pitch is less forgiving than a coarse-pitch package.

Permintaan RFG Kontak
ATXMEGA32A4U-AU - 32MHz 32KB AVR MCU | Microchip Technology
ATXMEGA32A4U-AU

ATXMEGA32A4U-AU - 32MHz 32KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA32A4U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller with a 32 MHz clock, 32 KB self-programming Flash memory, 4 KB SRAM, and 1 KB EEPROM. It is packaged in a 44-pin TQFP measuring 10 mm by 10 mm and operates from a 1.6 V to 3.6 V supply. The device integrates 34 general-purpose I/O lines, a four-channel DMA controller, an eight-channel event system, and extensive timer, serial, and analog peripherals. An 8/16-bit AVR microcontroller is a compact embedded-processing device built around the enhanced AVR RISC architecture. In the broader semiconductor hierarchy, this MCU belongs to the Microcontrollers class, combines a CPU core with memory and peripherals on one package, and supports low-power control applications where deterministic timing, event handling, and flexible serial communication are important. The XMEGA A4U family is positioned between basic 8-bit AVR devices and higher-performance 32-bit microcontrollers. Key features include read-while-write Flash operation, a dedicated 4 KB boot-code section, internal EEPROM and SRAM, a four-channel DMA controller, and an eight-channel event system. Five flexible 16-bit timer/counter blocks provide compare, capture, and PWM functions, while five USARTs and two Two-Wire Interfaces support factory instrumentation, industrial control, and board-to-board communication. A 16-bit Real Time Counter supports timekeeping, and the integrated analog resources support precision measurement and control. The XMEGA architecture separates high-speed peripherals from the CPU clock, allowing the event system to route signals without requiring continuous CPU intervention. DMA transfers data between peripherals and SRAM, reducing interrupt overhead during communication or sampling workloads. The programmable multilevel interrupt controller supports responsive event handling, while the bootloader and self-programming Flash provide a practical path for field updates. Typical uses include industrial data acquisition, compact motor-control systems, instrumentation, communications equipment, and low-power embedded controllers. Its combination of 32 MHz processing, multiple USARTs, PWM-capable timers, and DMA makes it useful where several asynchronous peripherals must operate concurrently. The 1.6 V to 3.6 V supply range also permits integration into systems that distribute regulated 1.8 V or 3.3 V power. PCB design should preserve the voltage, ground, decoupling, clock, and programming connections shown in the manufacturer pin description. Place decoupling capacitors close to the supply pins, route sensitive analog and clock signals away from fast-switching nodes, and follow the recommended programming interface layout. Because firmware peripherals and package options can differ across XMEGA revisions, verify the exact suffix and errata status before production release. This product page combines the manufacturer feature set, package information, verified cross-reference findings, and practical design guidance. It also distinguishes a genuine same-footprint option from similarly named devices whose architecture, memory configuration, temperature grade, or function is not electrically interchangeable.

Permintaan RFG Kontak
ATXMEGA32A4U-CU - 32MHz 32KB 49-VFBGA MCU | Microchip
ATXMEGA32A4U-CU

ATXMEGA32A4U-CU - 32MHz 32KB 49-VFBGA MCU | Microchip

The Microchip Technology ATXMEGA32A4U-CU is an 8/16-bit AVR XMEGA microcontroller operating at up to 32 MHz, with 32 KB of self-programming Flash memory and 49-VFBGA packaging on a 5 x 5 mm footprint. It also includes 4 KB of SRAM, a 4 KB boot-code section, and 1 KB of EEPROM for embedded applications requiring a compact combination of processing, memory, and peripherals. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The ATXMEGA family combines an AVR RISC processing architecture with advanced event-system, DMA, and external-bus capabilities. Within the semiconductor hierarchy, this device belongs to the embedded MCU family and the broader category of microcontrollers used for industrial control, communications, data acquisition, and compact automation. Key features include a 32 MHz maximum clock, 32 KB self-programming Flash, 4 KB SRAM, 4 KB dedicated boot-code memory, and 1 KB EEPROM. The four-channel DMA controller transfers data without continuous CPU intervention, while the eight-channel event system links peripherals through hardware signals. The device also supports an external bus interface for connecting additional memory or peripheral components when the internal resources are insufficient. The ATXMEGA32A4U-CU uses the AVR instruction set and supports operating voltage options of 1.8 V, 2.5 V, and 3.3 V. Its 49-VFBGA package minimizes board area but requires careful escape routing because the 5 x 5 mm footprint provides closely spaced peripheral connections. Program development uses the AVR toolchain, with application configuration based on the device’s fuses, boot loader, and XMEGA peripheral architecture. Typical applications include industrial sensor nodes, compact data-acquisition systems, communication equipment, embedded control modules, and low-power instrument controllers. The hardware DMA and event system are especially useful when deterministic peripheral timing is needed, such as sampling ADCs, transferring blocks of data, or synchronizing timers without routing every event through the CPU. PCB design should account for the 49-VFBGA geometry, provide a continuous ground reference where practical, route escape lines according to the manufacturer land pattern, and place decoupling capacitors close to the supply pins. Firmware development should preserve the 4 KB boot-code region unless boot-loader use is intentional and verify clock, brownout, and programming configuration against the manufacturer datasheet before production. This page organizes the ATXMEGA32A4U-CU memory architecture, package characteristics, drop-in candidates, application guidance, and design considerations into a practical engineering reference. It also clarifies the distinctions among ordering variants that share the 49-VFBGA footprint but differ in grade, temperature option, or device feature set.

Permintaan RFG Kontak
ATXMEGA32C3-AN - 32MHz 32KB Flash AVR Microcontroller | Microchip
ATXMEGA32C3-AN

ATXMEGA32C3-AN - 32MHz 32KB Flash AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA32C3-AN is an 8/16-bit AVR XMEGA microcontroller operating at 32 MHz with 32 KB of in-system programmable Flash, 2 KB of EEPROM, 4 KB of SRAM, and a 64-TQFP 14 x 14 mm package. It is designed for embedded systems that require deterministic real-time control, flexible peripherals, and a compact surface-mount footprint. The device supports read-while-write operation and includes a dedicated 8 KB boot-code section. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The ATXMEGA32C3 belongs to the hierarchy of 8/16-bit microcontrollers, embedded processors, and programmable control ICs. Its AVR architecture combines an instruction set optimized for embedded control with event-system and interrupt resources that help coordinate timing-sensitive tasks without relying entirely on software polling. Key features include 32 KB of Flash memory, 2 KB of EEPROM, 4 KB of SRAM, 50 general-purpose I/O pins, and a four-channel event system. The manufacturer describes the family as a programmable multilevel interrupt controller with 32 MHz processing. A 1.6 V to 3.6 V operating range supports low-voltage embedded systems, while the listed temperature rating of 105 C supports applications beyond conventional commercial temperature limits. The ATXMEGA family architecture places communication and timing functions close to the CPU. The event system can connect peripherals through direct event channels, reducing CPU intervention for deterministic tasks. The four-channel event system is particularly useful for high-speed timing, sensor acquisition, and signal-generation workflows where predictable event relationships are more valuable than raw instruction throughput. Read-while-write Flash operation can also simplify firmware-update or boot-related implementations. Typical uses include industrial control modules, compact sensor nodes, data-acquisition equipment, motor-control peripherals, communications equipment, and embedded accessories. Its 64-pin package provides substantially more I/O than smaller microcontroller packages while remaining manageable for automated assembly and multilayer PCB layouts. The 32 MHz clock rate and 32 KB memory footprint suit control-oriented designs that do not require a high-end processor or large graphical user interface. Design around the 1.6 V to 3.6 V supply range, decoupling requirements, clock configuration, programming interface, and exposed peripheral pins specified in the manufacturer datasheet. Confirm boot-loader, USB, ADC, timer, and communications requirements during device selection because firmware and peripheral availability depend on the exact family variant. This page combines manufacturer specifications, purchasing guidance, and drop-in alternatives to support engineering evaluation. For a new design, ATXMEGA32C3-AN offers a useful balance of processing speed, memory, real-time peripherals, and board area. It is most appropriate when deterministic event handling and AVR software compatibility matter more than the very small package area or low cost of a minimal 8-bit controller.

Permintaan RFG Kontak
ATXMEGA32C3-ANR - 32MHz 32KB Flash AVR Microcontroller | Microchip (Tape & Reel)
ATXMEGA32C3-ANR

ATXMEGA32C3-ANR - 32MHz 32KB Flash AVR Microcontroller | Microchip (Tape & Reel)

The Microchip Technology ATXMEGA32C3-ANR is an 8/16-bit AVR XMEGA microcontroller operating at 32 MHz with 32 KB of in-system programmable Flash, 2 KB of EEPROM, 4 KB of SRAM, and a 64-TQFP 14 x 14 mm package. It is designed for embedded systems that require deterministic real-time control, flexible peripherals, and a compact surface-mount footprint. The device supports read-while-write operation and includes a dedicated 8 KB boot-code section. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The ATXMEGA32C3 belongs to the hierarchy of 8/16-bit microcontrollers, embedded processors, and programmable control ICs. Its AVR architecture combines an instruction set optimized for embedded control with event-system and interrupt resources that help coordinate timing-sensitive tasks without relying entirely on software polling. Key features include 32 KB of Flash memory, 2 KB of EEPROM, 4 KB of SRAM, 50 general-purpose I/O pins, and a four-channel event system. The manufacturer describes the family as a programmable multilevel interrupt controller with 32 MHz processing. A 1.6 V to 3.6 V operating range supports low-voltage embedded systems, while the listed temperature rating of 105 C supports applications beyond conventional commercial temperature limits. The ATXMEGA family architecture places communication and timing functions close to the CPU. The event system can connect peripherals through direct event channels, reducing CPU intervention for deterministic tasks. The four-channel event system is particularly useful for high-speed timing, sensor acquisition, and signal-generation workflows where predictable event relationships are more valuable than raw instruction throughput. Read-while-write Flash operation can also simplify firmware-update or boot-related implementations. Typical uses include industrial control modules, compact sensor nodes, data-acquisition equipment, motor-control peripherals, communications equipment, and embedded accessories. Its 64-pin package provides substantially more I/O than smaller microcontroller packages while remaining manageable for automated assembly and multilayer PCB layouts. The 32 MHz clock rate and 32 KB memory footprint suit control-oriented designs that do not require a high-end processor or large graphical user interface. Design around the 1.6 V to 3.6 V supply range, decoupling requirements, clock configuration, programming interface, and exposed peripheral pins specified in the manufacturer datasheet. Confirm boot-loader, USB, ADC, timer, and communications requirements during device selection because firmware and peripheral availability depend on the exact family variant. This page combines manufacturer specifications, purchasing guidance, and drop-in alternatives to support engineering evaluation. For a new design, ATXMEGA32C3-ANR offers a useful balance of processing speed, memory, real-time peripherals, and board area. It is most appropriate when deterministic event handling and AVR software compatibility matter more than the very small package area or low cost of a minimal 8-bit controller.

Permintaan RFG Kontak
ATXMEGA32C3-AU - 32MHz 32KB Flash MCU | Microchip | TQFP-64
ATXMEGA32C3-AU

ATXMEGA32C3-AU - 32MHz 32KB Flash MCU | Microchip | TQFP-64

The Microchip Technology ATXMEGA32C3-AU is an 8/16-bit AVR XMEGA C3-series microcontroller operating at up to 32 MHz, with 32 KB of Flash memory, 2 KB of EEPROM, and 4 KB of SRAM in a 64-pin TQFP package. It is designed for compact embedded systems that require deterministic control, flexible serial communications, and low-power operation without relying on a high-pin-count package. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, peripherals, and interface circuitry on one device. Within the embedded-control hierarchy, the ATXMEGA32C3 belongs to the AVR 8/16-bit MCU family and uses the Harvard-style AVR architecture, which separates program-memory access from the data-memory path. This structure supports efficient instruction execution in applications involving sensors, communication interfaces, motor control, and local human-machine interaction. The ATXMEGA32C3-AU combines 32 KB of in-system programmable Flash with read-while-write capability, 2 KB of EEPROM, and 4 KB of SRAM. Its four-channel event system can coordinate timing-sensitive tasks without excessive interrupt servicing. The device also provides a 12-bit ADC, multiple timer/counter resources, and serial interfaces suitable for industrial, consumer, and communication-oriented embedded products. The industrial-temperature ordering designation identifies it for extended-temperature equipment applications. Its 32 MHz operating speed provides useful performance for protocol handling, signal conditioning, sampling, and supervisory control. The four-channel event system is particularly valuable when several peripheral actions must occur with predictable timing. Program memory can be updated in-system, supporting configuration changes and firmware maintenance, while read-while-write operation allows code execution to continue when flash locations do not overlap the active program section. Typical uses include industrial sensor nodes, building-automation controllers, motor-control interfaces, compact data loggers, communication modules, and embedded measurement equipment. The combination of SRAM, EEPROM, timers, ADC channels, and serial peripherals allows one device to consolidate functions that might otherwise require several discrete components. The primary design consideration is package and firmware compatibility. A 64-pin TQFP footprint requires adequate PCB routing space, and new designs should follow the Microchip pin description, recommended decoupling, clock, and programming-interface layouts. Firmware replacement also requires review of boot sections, interrupt vectors, peripheral resources, and application-specific timing rather than treating every electrically similar device as functionally identical. This product record combines manufacturer specifications, package details, sourcing guidance, and engineering-focused design guidance to support initial component selection and board-level implementation. It also distinguishes exact ordering variants from genuine pin-compatible alternatives so that footprint and firmware decisions are not based solely on a matching package name.

Permintaan RFG Kontak
ATXMEGA32C3-MH - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA32C3-MH

ATXMEGA32C3-MH - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA32C3-MH is a high-performance, low-power 8/16-bit AVR XMEGA C3 microcontroller running at 32 MHz, integrating 32 KB of in-system programmable Flash memory (with an 8 KB boot-code section and read-while-write capability), 2 KB EEPROM and 4 KB SRAM, all housed in a 64-pin VQFN (9x9 mm) exposed-pad package. An 8/16-bit microcontroller (MCU) is a single-chip computer built around an 8- or 16-bit data path that integrates a CPU core, non-volatile Flash program memory, volatile SRAM data memory, EEPROM for parameter storage, plus a rich set of on-chip peripherals (timers, ADC/DAC, communication controllers, GPIO). The ATXMEGA32C3 belongs to the XMEGA family in the broader hierarchy: 8/16-bit MCU -> microcontroller -> embedded processor -> semiconductor. It uses the AVR RISC instruction set with hardware multiplier, executes most instructions in a single clock cycle, and is targeted at industrial-grade, low-power embedded designs that need deterministic real-time response. Key features of the ATXMEGA32C3-MH include four flexible 16-bit Timer/Counter modules, a 12-channel event system, a four-channel DMA controller that moves data without CPU intervention, a 12-bit ADC and 12-bit DAC, USB device support, AES/DES crypto acceleration, and an operating voltage range of 1.6 V to 3.6 V. Its 32 MHz core delivers up to 32 MIPS of throughput, and the integrated PicoPower technology reduces active and sleep-mode current. Architecturally, the device pairs an event-driven peripheral fabric with the DMA controller, allowing analog conversion, packet transmission, and timer capture to run autonomously while the CPU sleeps. This architecture is well-suited to deterministic, low-latency control applications such as sensor hubs, motor control, and human-interface subsystems. Typical applications include industrial sensor interfaces, USB-enabled consumer devices, building automation controllers, smart-metering subsystems, and human-machine interface (HMI) panels. The wide 1.6V-3.6V supply range also allows direct battery operation. When designing with this device, ensure the 64-pin VQFN exposed pad is soldered to a sufficient ground copper pour for thermal and electrical performance. Decouple VDD with at least one 100 nF ceramic capacitor per supply pin placed as close as possible to the package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a single reference for engineers evaluating the ATXMEGA32C3-MH for new designs.

Permintaan RFG Kontak
ATXMEGA32C3-MHR - 32KB Flash 8/16-bit AVR XMEGA MCU 64-QFN
ATXMEGA32C3-MHR

ATXMEGA32C3-MHR - 32KB Flash 8/16-bit AVR XMEGA MCU 64-QFN

The Microchip Technology ATXMEGA32C3-MHR is a high-performance, low-power 8/16-bit AVR XMEGA C3 microcontroller integrating 32 KB of in-system programmable Flash memory (with an 8 KB boot code section that supports read-while-write operation), 2 KB EEPROM, and 4 KB SRAM, housed in a 64-pin 9x9 mm QFN package. It executes instructions in a single clock cycle and reaches up to 32 MHz CPU throughput, delivering nearly 1 MIPS per MHz while keeping active power consumption low. The part supports a 1.6 V to 3.6 V supply range and is qualified for industrial temperature operation. What is an AVR XMEGA microcontroller? The XMEGA family extends Atmel's AVR enhanced RISC architecture into the 8/16-bit microcontroller segment. It belongs to the wider hierarchy: microcontroller (MCU) -> 8/16-bit MCU -> AVR core MCU -> XMEGA family. XMEGA devices are positioned between classic 8-bit AVR microcontrollers and 32-bit ARM Cortex-M parts, offering richer peripherals (DMA, event system, crypto engine on some variants) than classic AVR while retaining a single-cycle RISC core that is simple to program in C. Key features include a four-channel event system for inter-peripheral signaling without CPU intervention, a programmable multi-level interrupt controller, 50 general-purpose I/O pins, a full-speed USB device interface, multiple USART/SPI/TWI peripherals, a 12-bit ADC and DAC, and AES/DES crypto acceleration on selected variants. The 32 KB Flash supports application programming through boot-loader, JTAG, or PDI interfaces. Industrial-grade temperature range (-40C to +85C) and 1.6-3.6 V operation make it suitable for battery-powered and harsh-environment designs. A 12 mA maximum active supply current is specified in the brief, while sleep-mode currents are in the microamp range. Architecturally, the ATXMEGA32C3 uses the AVR enhanced RISC core with a multi-stage pipeline and Harvard bus architecture that allows instruction fetch and memory access to overlap. The four-channel event system routes peripheral triggers (timer, ADC, DMA) directly between peripherals, offloading the CPU. The 64-pin QFN package exposes the full peripheral set and supports up to 50 GPIO lines. Typical applications include industrial control panels, USB human-interface devices (HID), smart sensors with on-board crypto, low-power IoT edge nodes, building automation, and consumer electronics with touch or display interfaces. The AES/DES hardware accelerator enables secure firmware and authenticated sensor links. The part is widely used in designs that migrate from older ATmega MCUs but need more peripherals and lower active power. A key design consideration is decoupling: place 100 nF and 1 uF ceramic capacitors close to each VCC pin and provide adequate ground stitching under the QFN thermal pad to minimize EMI. Program/debug is performed through the PDI (Program and Debug Interface) two-wire protocol rather than JTAG on this device family. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
ATXMEGA32C3-MN - 32MHz 32KB Flash MCU | Microchip
ATXMEGA32C3-MN

ATXMEGA32C3-MN - 32MHz 32KB Flash MCU | Microchip

The Microchip ATXMEGA32C3-MN is a 32 MHz AVR XMEGA 8/16-bit microcontroller with 32 KB of in-system programmable Flash memory, 2 KB of EEPROM, 4 KB of SRAM, and a 64-pin VQFN package with an exposed pad. It operates from a 1.6 V to 3.6 V supply, providing a compact solution for embedded control, communication, and low-power applications. An AVR XMEGA microcontroller combines an 8-bit AVR-compatible instruction set with a high-performance 32 MHz pipeline and an event system designed to transfer events directly between peripherals. This architecture belongs to the broader microcontroller hierarchy: embedded controller, general-purpose MCU, AVR core, and system-on-chip. It is useful when a design needs deterministic peripheral coordination without relying on frequent central-processor intervention. The ATXMEGA32C3 includes 32 KB of Flash memory, with 8 KB reserved as a boot-code section, and supports read-while-write operation. Its 2 KB EEPROM provides nonvolatile storage for configuration parameters, while 4 KB of SRAM supports stack, buffering, and real-time processing. The four-channel event system allows communication between timers, analog comparators, pin-change functions, and other interrupt-capable peripherals. The 64-pin VQFN package exposes substantially more I/O than a small leaded MCU package, supporting integration of communications, control inputs, analog functions, and debug functions on a compact surface-mount footprint. Its 32 MHz operating speed provides additional timing margin for protocol handling and control loops. The exposed thermal pad improves heat transfer from the device into the PCB copper plane. Typical uses include industrial control modules, sensor nodes, building automation, compact data acquisition, motor or actuator supervision, and communications-enabled embedded products. The combination of EEPROM, SRAM, Flash, event handling, and a large pin count makes the device suitable for designs that need local configuration storage, moderate real-time processing, and numerous peripheral connections. PCB design should preserve the exposed-pad land pattern, connect the thermal and ground structure as specified by the package drawing, and route high-current or sensitive signals away from the MCU clock and power pins. Firmware design should use the event system for latency-sensitive peripheral links, while the processor handles supervisory logic and protocol tasks. The ATXMEGA32C3-MN is a surface-mount component intended for automated assembly. This page consolidates the manufacturer specifications, package details, design considerations, application guidance, and verified sourcing information into an engineering-focused reference for evaluating the ATXMEGA32C3-MN in new embedded designs.

Permintaan RFG Kontak