Produk (22.000+)

ATTINY12-8SI - 8-Bit AVR, 8MHz, 1KB Flash | Microchip Technology
ATTINY12-8SI

ATTINY12-8SI - 8-Bit AVR, 8MHz, 1KB Flash | Microchip Technology

Microchip Technology ATTINY12-8SI is an 8-bit AVR ATtiny microcontroller operating at 8MHz, with 1KB of Flash program memory organized as 512 x 16 words and 64 bytes of EEPROM data memory. The device is offered in an 8-pin SOIC package and is identified as an industrial-temperature variant. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, and digital input/output circuitry on one device. The ATTINY12-8SI belongs to the ATtiny family, within the broader AVR microcontroller and embedded-controller hierarchy. Its small memory capacity and limited pin count make it suitable for compact control tasks rather than general-purpose applications requiring extensive code storage or peripheral connectivity. The principal characteristics include an 8-bit AVR core, 8MHz clock rating, 1KB Flash memory, 64 bytes of EEPROM, and an 8-SOIC package. These parameters support small embedded routines such as state sequencing, simple signal generation, switching control, and basic logic coordination. The 512-word Flash organization provides 1KB of code storage, while the EEPROM provides a small amount of nonvolatile data storage separate from program memory. The ATtiny12 architecture places significant emphasis on compact implementation. With only eight pins, external signal allocation requires careful pin planning, and the available GPIO resources are limited compared with larger ATtiny devices. Program development must therefore remain compact, and peripheral functions must be selected around the actual pin requirements of the target circuit. The 8MHz maximum clock supports faster execution than lower-speed microcontrollers while retaining a straightforward embedded-control architecture. Typical uses include small industrial control modules, LED sequencing and lighting controllers, compact timers, simple sensor interfaces, and auxiliary control functions in larger equipment. It is most appropriate where the firmware can fit within 1KB and only a small number of external signals is required. Designs needing serial communication, larger data storage, more I/O, or substantially more program memory should use a higher-capacity microcontroller instead. For PCB implementation, place the decoupling capacitor close to the VCC pin and route the ground connection with minimal resistance. Confirm every use of the reset-capable and ADC-capable pins against the manufacturer pin-description table, especially when the package footprint is shared with another ATtiny family member. The industrial-temperature ordering code must also be confirmed against the system’s environmental requirements before release to production. This product page combines the manufacturer identity, core operating parameters, memory configuration, package information, application guidance, and qualified drop-in alternatives into one engineering reference. It also highlights the limits of the ATTINY12-8SI so purchasing teams can distinguish genuine pin-compatible replacements from larger microcontrollers that share the SOIC-8 format but require different firmware, pin assignments, or peripheral resources.

Permintaan RFG Kontak
ATTINY12-8SU 8MHz 1KB AVR Microcontroller | Microchip Technology
ATTINY12-8SU

ATTINY12-8SU 8MHz 1KB AVR Microcontroller | Microchip Technology

The Microchip Technology ATTINY12-8SU is an 8-bit AVR RISC microcontroller with 1KB of Flash program memory, 64 bytes of EEPROM, 6 I/O pins, and an operating speed of 8MHz. The device operates from a 4V to 5.5V supply and is packaged in an 8-pin SOIC surface-mount package. It is designed for compact embedded-control tasks where low component count, simple firmware, and deterministic digital I/O are more important than high memory capacity. A microcontroller is a programmable semiconductor that combines a processor core, program memory, data memory, and peripherals in one integrated circuit. The ATTINY12-8SU belongs to the AVR family, using a RISC architecture and a compact instruction set suitable for simple control systems. Its 1KB Flash memory stores the application program, while its 64-byte EEPROM supports nonvolatile parameter storage. The small 8-pin package also makes the device suitable for space-constrained consumer, industrial-control, and accessory products. Key features include an 8MHz internal-clock operating speed, 1KB of Flash program memory, 64 bytes of EEPROM, six I/O pins, and a 4V to 5.5V operating supply range. The limited memory footprint makes firmware organization and external peripheral use central to the design process. The ATTINY12-8SU is appropriate for simple state machines, push-button interfaces, LED indicators, basic timing, and control functions that do not require networking, large data storage, or high-resolution analog conversion. The AVR architecture provides a compact execution environment for embedded logic, while the ATtiny12 family targets cost-sensitive applications with modest processing requirements. Because the device has only 1KB of Flash memory, the firmware should reserve space for initialization, interrupt handling, application logic, and any required library routines. Persistent settings should use the EEPROM conservatively because its capacity is limited to 64 bytes. External sensing or actuation may therefore be necessary when the application requires more I/O, memory, or peripheral capability. Typical uses include simple appliance controls, keyboard interfaces, small sensor-conditioning systems, LED status controllers, and compact embedded automation modules. In these applications, the ATTINY12-8SU can replace a discrete combination of logic gates, timers, and state-control circuitry while simplifying firmware maintenance. Its 8MHz clock provides ample timing resolution for basic control loops, debounce routines, and sequential output control. Designers should confirm the external crystal or clock requirements, regulator tolerance, input thresholds, and pin multiplexing before committing a board layout. Place decoupling capacitors close to the supply pins and provide adequate pull-up or pull-down resistors for open-drain communication lines. Firmware validation should include reset behavior, brownout conditions, unused-pin states, and worst-case bus timing. This product page combines the ATTINY12-8SU electrical identity, package and memory details, application guidance, replacement analysis, and practical design considerations for engineers evaluating compact 8-bit embedded-control designs.

Permintaan RFG Kontak
ATTINY12L-4PU - 8-Bit 4MHz AVR Microcontroller | Microchip
ATTINY12L-4PU

ATTINY12L-4PU - 8-Bit 4MHz AVR Microcontroller | Microchip

The Microchip ATTINY12L-4PU is an 8-bit AVR RISC microcontroller with a 4 MHz clock, 1 KB of nonvolatile Flash program memory, 64 bytes of EEPROM data memory, and a 2.7 V to 5.5 V supply range, housed in an 8-pin PDIP package. It is designed for compact embedded-control tasks where low cost, low pin count, and deterministic single-cycle instruction execution are more important than extensive memory or peripheral integration. An 8-bit microcontroller is a programmable integrated circuit that executes a compact instruction set while reading instructions and data from nonvolatile memory. The ATTINY12L belongs to the AVR family, whose architecture uses 8 general-purpose working registers and 90 instructions. Within the product hierarchy, it sits between simple logic controllers and larger microcontrollers with considerably more RAM, Flash, timers, and communication peripherals. Important device characteristics include 1 KB of Flash organized as 512 words by 16 bits, 64 bytes of EEPROM, six I/O pins, and operation from 2.7 V to 5.5 V. The device is fully static, allowing processing to stop when the clock is stopped. Its reduced-pin architecture is useful when a design needs basic control functions, indicator outputs, key scanning, or a small autonomous sequencer rather than a high-bandwidth communications controller. The ATTINY12L-4PU uses an advanced RISC-style AVR core with most instructions completing in a single clock cycle. Program storage remains nonvolatile, while the small EEPROM area supports parameters, calibration values, counters, and configuration data that must survive a power interruption. Because the device has limited memory, firmware structure, lookup tables, and buffer sizing require deliberate attention. Typical applications include simple timers, relay-control modules, LED status indicators, battery-operated instruments, fan controllers, and compact sensing interfaces. It is also appropriate for teaching and prototyping environments where an 8-pin controller, 4 MHz operation, and a simple development toolchain simplify initial hardware bring-up. PCB layout should keep the supply and ground connections short and provide adequate bypass capacitance near the device. Because the ATTINY12L-4PU is a PDIP-8 part, consider mechanical availability, assembler compatibility, and the lead-spacing requirements of the target PCB before placing the component in a new high-volume design. This page combines the device specifications, package information, sourcing guidance, verified drop-in alternatives, and practical design considerations needed to evaluate the ATTINY12L-4PU for compact embedded-control projects.

Permintaan RFG Kontak
ATTINY12L-4SU - 4MHz 8-Bit AVR MCU | Microchip Technology
ATTINY12L-4SU

ATTINY12L-4SU - 4MHz 8-Bit AVR MCU | Microchip Technology

The Microchip Technology ATTINY12L-4SU is an 8-bit AVR RISC microcontroller with a 4 MHz clock, 1 KB of Flash program memory, 64 bytes of EEPROM, and a 3.3 V to 5 V supply range, housed in an 8-pin SOIC package. Its compact architecture supports basic control, timing, signal-processing, and low-power embedded functions. An 8-bit microcontroller is a compact embedded processor designed to execute control logic, measure inputs, manage outputs, and maintain system state. The ATtiny family belongs to the AVR product line, where the reduced-instruction-set controller combines nonvolatile program storage, digital I/O, timers, and power-management functions in one integrated circuit. The ATTINY12L is positioned at the entry level of this hierarchy and is suited to applications that do not require a large working memory or extensive peripheral set. The ATTINY12L-4SU combines 1 KB of Flash memory organized as 512 words by 16 bits, 64 bytes of EEPROM, and eight general-purpose working registers. Its four principal features include 4 MHz operation, single-clock-cycle execution for most instructions, fully static operation, and nonvolatile program memory. The -4 suffix identifies the 4 MHz speed grade, while the U suffix identifies the surface-mount SOIC shipping configuration. The AVR RISC architecture provides compact, efficient execution for control-oriented firmware. Because most instructions complete in one clock cycle, the processor can combine meaningful computational activity with low system power consumption. Nonvolatile Flash retains the programmed application after power removal, while EEPROM supports nonvolatile parameter or configuration storage without consuming the limited program-memory budget. Typical uses include simple motor or actuator controllers, compact sensor interfaces, LED status and indicator systems, low-cost measurement products, household appliance controls, and small industrial control modules. The device is especially appropriate when the control task fits within 1 KB of Flash and does not require the memory, pin count, or peripheral set of a larger 8-bit or 32-bit MCU. Circuit design should preserve the supply-voltage limits, provide adequate decoupling at the power pins, and assign every external signal to the pin defined in the manufacturer pin-description table. Designers should also confirm startup behavior, clock configuration, reset requirements, and I/O limits in the manufacturer datasheet before releasing a production PCB. This page combines the key electrical characteristics, practical design guidance, application fit, and drop-in replacement analysis needed to evaluate the ATTINY12L-4SU as an 8-pin, 4 MHz AVR control solution.

Permintaan RFG Kontak
ATTINY12V-1PU - 8-Bit 1MHz AVR MCU | Microchip
ATTINY12V-1PU

ATTINY12V-1PU - 8-Bit 1MHz AVR MCU | Microchip

The Microchip Technology ATTINY12V-1PU is an 8-bit AVR microcontroller with 1 KB of Flash program memory, 64 bytes of EEPROM, six I/O ports, and a 1 MHz clock in an 8-pin PDIP package. Designed for compact embedded-control tasks, it combines an AVR RISC core, low-power operating modes, and a small pin count in a 0.300-inch, 7.62 mm-wide dual in-line package. An 8-bit microcontroller is a compact processor designed around an 8-bit data path for embedded control rather than desktop computing. The ATTINY12 belongs to the ATtiny hierarchy within AVR microcontrollers, combining a CPU core, nonvolatile program memory, data EEPROM, and general-purpose I/O in one package. This integration allows a small controller to sense inputs, execute embedded logic, and operate outputs without a separate processor or memory device. The ATTINY12V-1PU provides 1 KB of Flash memory for firmware, 64 bytes of EEPROM for retained data, and six I/O ports. Its low-power CMOS implementation supports operation across the device's stated supply-voltage options of 2.5 V, 3.3 V, and 5 V. The device uses the AVR instruction architecture and is suitable for simple sequencing, logic, debouncing, signal generation, and compact peripheral-control functions where memory and processing requirements are modest. At the system level, the microcontroller's small footprint makes it useful in prototypes, automation modules, educational boards, and dedicated appliance controls. The PDIP format is particularly convenient for breadboards, fixture-based programming, and low-volume fabrication because its 0.300-inch pitch provides generous spacing between pins. Unlike fine-pitch surface-mount packages, the through-hole body is straightforward to inspect and rework. Typical uses include relay timing, LED indication, push-button interfaces, simple sensor conditioning, low-speed control loops, and compact embedded logic modules. Because the device has only 1 KB of program memory, applications should use concise firmware, avoid unnecessary library overhead, and keep buffering or computation requirements modest. PCB design should provide a stable decoupling capacitor near the supply pin, preserve adequate ground-return paths, and keep switching or high-current outputs separated from sensitive input traces. Confirm oscillator, reset, programming, and I/O requirements against the manufacturer datasheet before finalizing the schematic or PCB footprint. This page combines the device specifications, pin-level guidance, application context, verified drop-in candidates, and practical implementation notes needed to evaluate the ATTINY12V-1PU before schematic capture or sourcing.

Permintaan RFG Kontak
ATTINY12V-1SU - 8-Bit 1KB AVR MCU | Microchip Technology
ATTINY12V-1SU

ATTINY12V-1SU - 8-Bit 1KB AVR MCU | Microchip Technology

The Microchip Technology ATTINY12V-1SU is an 8-bit AVR RISC microcontroller with 1 KB of Flash program memory, 64 bytes of EEPROM, a 1.2 MHz operating speed, and an 8-pin SOIC package. It is designed for compact, low-power embedded control applications that require six general-purpose I/O pins and an internal oscillator. A microcontroller is a programmable semiconductor that integrates a processor core, memory, I/O ports, and basic peripherals onto one package. The ATTINY12V-1SU belongs to the AVR microcontrollers family, where the reduced-instruction-set computer core executes instructions efficiently in a single clock cycle. Its small memory footprint and limited peripheral set make it appropriate for simple control logic rather than general-purpose computing. Key features include 1 KB of Flash program memory, 64 bytes of EEPROM, 64 bytes of SRAM, and six I/O pins. The device operates from a 1.8 V to 5.5 V supply range and includes an internal oscillator, power-on reset, watchdog timer, and brown-out detection. An operating speed of 1.2 MHz provides sufficient processing capability for compact sensors, basic motor controllers, and simple consumer-product functions. The AVR RISC architecture provides efficient instruction execution while keeping the device economical in both board area and power consumption. Program and data memories are organized for firmware-oriented embedded use, while EEPROM preserves small amounts of configuration or calibration data across power cycles. The internal oscillator eliminates the need for an external clock source in designs that do not require precise timing. Typical uses include low-cost control boards, LED indicators, battery-operated accessories, simple sensor interfaces, and compact power-management controllers. The six available I/O pins support digital input and output functions, while the internal watchdog provides a mechanism for recovering from unexpected program-flow faults. The SOIC package also makes the device practical for leaded-assembly and conventional surface-mount PCB layouts. When designing around ATTINY12V-1SU, account for the limited 1 KB program memory when selecting application code and bootloader features. Keep decoupling close to the supply pins, use the brown-out and watchdog functions where reliability matters, and confirm the programmed operating voltage before driving external loads. Its strengths are simplicity, low cost, and compactness rather than high processing throughput or extensive connectivity. This page combines package, memory, power, and lifecycle information with practical design guidance, sourcing instructions, and a requirement-focused comparison. It also identifies where direct drop-in alternatives are justified, helping engineers distinguish true pin-compatible substitutions from devices that merely belong to the broader microcontroller category.

Permintaan RFG Kontak
ATTINY13-20MU - 20MHz 8-Bit AVR MCU | Microchip Technology
ATTINY13-20MU

ATTINY13-20MU - 20MHz 8-Bit AVR MCU | Microchip Technology

The Microchip Technology ATTINY13-20MU is an 8-bit AVR microcontroller operating at up to 20 MHz, with 1 KB of Flash memory, 64 bytes of EEPROM, and 64 bytes of SRAM in a 20-QFN-EP 4 mm × 4 mm package. The device operates from 2.7 V to 5.5 V and includes an analog-to-digital converter. Its compact package, low-voltage operation, and integrated serial programming support make it suitable for embedded control, sensor acquisition, and compact consumer-device designs. An 8-bit microcontroller is a programmable control IC that integrates a processor core, nonvolatile program memory, data memory, and peripherals on one semiconductor die. The ATtiny family belongs to the AVR architecture, a reduced-instruction-computer design suited to compact embedded control. Within the product hierarchy, ATTINY13-20MU is a microcontroller, embedded controller, programmable logic device, and semiconductor. The principal device ratings are a 20 MHz maximum clock, 1 KB Flash organized as 512 × 16 bits, 64 bytes of EEPROM, and 64 bytes of SRAM. The Flash memory stores the application program, EEPROM provides nonvolatile data storage, and SRAM provides volatile working memory. The integrated ADC supports analog measurements, while the 2.7 V to 5.5 V supply range accommodates common low-voltage embedded systems. The 20-QFN-EP 4 mm × 4 mm package provides a compact surface-mount footprint and an exposed thermal pad for heat transfer through the PCB. Compared with a larger leaded package, this arrangement supports dense layouts but requires careful land-pattern and paste-control implementation. The exposed pad must be connected according to the manufacturer's recommended footprint and thermal design. Typical uses include battery-powered sensor nodes, compact LED controllers, simple motor or actuator controls, appliance interfaces, educational electronics, and small AVR-based control boards. The 1 KB program-memory limit makes code economy especially important, while the ADC allows an application to read analog inputs without adding a separate converter. For a new PCB, follow the manufacturer datasheet for the exact QFN land pattern, exposed-pad connection, decoupling, programming pins, and operating-voltage limits. Because the part is only 4 mm × 4 mm, inspect the assembled board for solder bridges around closely spaced pads and confirm the programming interface remains accessible. This page combines the exact ATTINY13-20MU specifications, a focused same-package replacement assessment, engineering design notes, and application guidance to support component selection, PCB design, firmware planning, and sourcing decisions.

Permintaan RFG Kontak
ATTINY13-20SU - 8-Bit 20MHz AVR MCU | Microchip Technology
ATTINY13-20SU

ATTINY13-20SU - 8-Bit 20MHz AVR MCU | Microchip Technology

The Microchip Technology ATTINY13-20SU is an 8-bit AVR RISC microcontroller with a maximum clock frequency of 20 MHz, 1 KB of in-system programmable Flash memory, and an 8-pin SOIC package. It also includes 64 bytes of SRAM, 64 bytes of EEPROM, a 32-byte register file, six I/O pins, and a four-channel 10-bit analog-to-digital converter. An 8-bit AVR microcontroller is a compact embedded-control device that executes instructions from programmable Flash through an AVR reduced-instruction-set computer core. The ATTINY13 belongs to the ATtiny family within the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Its combination of limited memory, mixed-signal peripherals, and a small package makes it suitable for compact controls, sensor interfaces, and simple timing systems. Core features include 20 MHz operation, 1 KB ISP Flash, 64-byte SRAM, 64-byte EEPROM, a four-channel 10-bit ADC, and six I/O pins. The internal EEPROM supports persistent configuration or calibration data, while in-system programming allows firmware to be loaded without removing the device. The ADC can monitor up to four analog channels, enabling compact products that need more than simple digital switching. The AVR architecture provides an 8-bit instruction set with separate program and data-memory spaces. At 20 MHz, the manufacturer describes throughput as 20 MIPS. The small 1 KB Flash capacity sharply limits code size, so peripheral initialization, application logic, and delay routines must be sized carefully. The 64-byte SRAM should be treated as a tight working-memory budget for applications with buffering or interrupt-heavy routines. Typical uses include low-cost sensor nodes, simple motor and relay controllers, compact LED indicators, battery-operated instruments, and educational AVR projects. The ADC makes the device useful for potentiometers, light sensors, thermistors, and other analog inputs. Its small footprint also suits hobbyist boards and custom compact modules where a larger microcontroller would add unnecessary cost and board area. When designing around the ATTINY13-20SU, prioritize code and SRAM budgeting, use ISP programming correctly, and follow the manufacturer's pin-description table when assigning PCB tracks. Confirm ADC reference and input limits against the operating voltage. Because the MCU has only six I/O pins, choose peripheral multiplexing carefully and provide the decoupling and programming interface recommended in the manufacturer documentation. This page combines the exact core specifications, verified same-package replacement candidates, pin and package guidance, application-focused design notes, and a parameter comparison intended to accelerate engineering selection without repeating the complete manufacturer datasheet.

Permintaan RFG Kontak
ATTINY13A-MMF - 20MHz 1KB Flash 8-Bit AVR | Microchip
ATTINY13A-MMF

ATTINY13A-MMF - 20MHz 1KB Flash 8-Bit AVR | Microchip

The Microchip Technology ATTINY13A-MMF is a low-power, picoPower 8-bit AVR microcontroller operating at up to 20 MHz, with 1 KB of flash memory and a 10-MLP 3x3 mm package. It supports a 1.8 V to 5.5 V operating range and integrates 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a four-channel 10-bit ADC. An 8-bit microcontroller is a compact digital controller that executes instructions from nonvolatile program memory and uses general-purpose input/output pins to monitor inputs or control external circuits. The ATTINY13A belongs to the TinyAVR family within the broader hierarchy of 8-bit AVR microcontrollers, embedded processors, and semiconductor devices. Its small memory footprint makes it appropriate for focused control tasks rather than complex graphical, networking, or high-volume data-processing applications. The device combines a 20 MHz maximum clock with single-cycle instruction execution, enabling throughput approaching 1 MIPS per MHz and up to 20 MIPS. Four 10-bit ADC channels provide basic analog measurement, while integrated EEPROM preserves calibration, configuration, or identification data without external memory. The manufacturer identifies the family as picoPower architecture, emphasizing efficient operation in compact embedded products. Programming is supported through In-Circuit Serial Programming and the MPLAB Snap debug interface. The ATTINY13A platform is commonly developed with Microchip toolchains and third-party AVR environments, making it useful for prototypes, simple control boards, timers, and small sensor interfaces. The 1 KB program memory requires careful code-size budgeting, especially when analog control, communication routines, and application logic are combined. Typical designs use the ATTINY13A-MMF in compact control modules, LED drivers, simple timers, sensor interfaces, and inexpensive USB-to-serial projects. Its 20 MHz operating capability allows responsive control and straightforward timer-based sequencing, while the 10-MLP package supports space-constrained PCB layouts. Programming requires a compatible connector and ISP-compatible programmer or bootloader arrangement. Designers should pay close attention to power sequencing, decoupling, exposed-pad layout, and programming access in the 10-MLP footprint. Keep the ADC reference and sensitive signal routing away from fast-switching nodes, and confirm the selected package land pattern before release. This page combines manufacturer specifications, sourcing information, package guidance, practical application notes, and a focused replacement analysis for engineers evaluating the ATTINY13A-MMF.

Permintaan RFG Kontak
ATTINY13A-MU - 20MHz 8-Bit AVR MCU | Microchip
ATTINY13A-MU

ATTINY13A-MU - 20MHz 8-Bit AVR MCU | Microchip

Microchip Technology ATTINY13A-MU is a low-power 8-bit AVR microcontroller rated for operation from 1.8 V to 5.5 V, with a maximum clock frequency of 20 MHz and up to 20 MIPS throughput. The device contains 1 KB of in-system-programmable Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a four-channel 10-bit ADC. It is packaged as a 20-QFN-EP in a 4 mm by 4 mm footprint. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and input/output pins into one device. The ATtiny13A belongs to the TinyAVR family, which is part of Microchip's 8-bit AVR portfolio and is commonly used for compact control tasks. Its enhanced RISC architecture executes many instructions in one clock cycle, allowing performance approaching 1 MIPS per MHz while helping designers balance processing throughput against power consumption. The principal features of the ATTINY13A-MU include 20 MHz operation, 1 KB of Flash memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a four-channel 10-bit analog-to-digital converter. The picoPower architecture is designed for low-power embedded systems. Peripherals identified for the ATtiny13A family include brown-out detection and reset, power-on reset, PWM, and a watchdog timer, while the product page also identifies In-System Programming support. The AVR enhanced RISC core provides an 8-bit processing platform with up to 20 MIPS throughput at 20 MHz. The 1 KB Flash capacity accommodates compact firmware, while the 64-byte EEPROM supports nonvolatile parameter storage and the 64-byte SRAM handles working data. The ADC provides four 10-bit channels for measurements from sensors, switches, resistive dividers, and simple analog interfaces. Operating voltage is stated as 1.8 V to 5.5 V, allowing integration with both low-voltage and conventional 5 V systems. Typical uses include compact LED controllers, simple sensor interfaces, button-driven controls, battery-operated accessories, hobby projects, and small embedded automation nodes. The four ADC channels are particularly useful when a design must monitor several analog quantities without adding a separate converter. ISP programming makes the device suitable for small production runs and prototype boards because firmware can be loaded through the programming interface after assembly. Designers should account for the limited 1 KB Flash and 64-byte SRAM when selecting a programming toolchain and organizing firmware. The I/O budget and analog channel requirements must also be checked against the exact 20-QFN-EP pin arrangement. Use the manufacturer pin-description table and package drawing during PCB layout, and confirm all operating conditions against the device's specified voltage and frequency limits. This product analysis combines the manufacturer specifications with practical guidance for firmware sizing, programming, analog measurement, and compact PCB design. It also distinguishes the ATTINY13A-MU from package variants and larger ATtiny devices whose memory, speed, or pin count changes the replacement decision.

Permintaan RFG Kontak
ATTINY13A-PU - 20MHz 8-Bit AVR MCU | Microchip
ATTINY13A-PU

ATTINY13A-PU - 20MHz 8-Bit AVR MCU | Microchip

The Microchip ATTINY13A-PU is an 8-bit AVR microcontroller with a 20 MHz maximum clock, 1 KB of in-system programmable flash, and an 8-PDIP package. It operates from 1.8 V to 5.5 V and provides 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a four-channel 10-bit ADC. The ATTINY13A-PU combines these resources in an 8-pin through-hole package for compact embedded control. An 8-bit microcontroller is a programmable semiconductor that executes instructions from embedded flash memory and uses registers, SRAM, and peripherals to control a system. The ATtiny13A belongs to the TinyAVR family within the AVR architecture and provides a practical balance of processing speed, memory, analog measurement, and low power operation for cost-sensitive embedded products. Its small pin count makes it especially useful where board area and simplicity are important. Core resources include 1 KB of flash, 64 bytes of SRAM, 64 bytes of EEPROM, and a 32-byte register file. The four-channel 10-bit ADC supports analog sensing, while the AVR enhanced RISC architecture executes instructions in a single clock cycle. At 20 MHz, the processor can approach 20 MIPS of instruction throughput under suitable operating conditions. In-system programming supports programming and reprogramming through the ICSP interface. The device is based on a low-power CMOS process and uses the AVR enhanced RISC architecture. The picoPower implementation is intended to improve power efficiency relative to the original ATtiny13 while retaining a familiar programming model and peripheral arrangement. A limited 1 KB flash capacity favors compact control routines, pin-change interrupts, timers, communication state machines, and other tasks that do not require a large application framework. Typical uses include LED lighting controls, small motor or actuator controllers, simple keypads, compact sensor interfaces, teaching boards, and low-cost embedded products. The four ADC channels make the device useful for reading resistive or analog sensors, while its GPIO pins can operate digital inputs and outputs. The 8-PDIP format also simplifies breadboard prototyping, hand assembly, repair, and educational experiments. Designers should allocate the small SRAM carefully and avoid duplicating library functions that consume substantial flash. Place the decoupling capacitor close to VCC, use the reset and programming pins according to the manufacturer data sheet, and verify ADC input limits against the selected operating voltage. When timing, brown-out detection, or power-consumption behavior is important, review the device-specific electrical characteristics before production release. This product record combines the manufacturer data sheet, programming resources, package information, and application-oriented guidance. It also identifies the clearest same-package drop-in alternative and explains the hardware and software checks that should accompany any replacement decision.

Permintaan RFG Kontak
ATTINY13A-SF - 20MHz 1KB AVR MCU | Microchip Technology
ATTINY13A-SF

ATTINY13A-SF - 20MHz 1KB AVR MCU | Microchip Technology

Microchip Technology ATTINY13A-SF is a picoPower 8-bit AVR RISC-based microcontroller with 1 KB of ISP Flash, 64 bytes of EEPROM, 64 bytes of SRAM, and a 4-channel 10-bit ADC, operating up to 20 MHz in an 8-pin SOIC package. It supports 1.8 V to 5.5 V operation and delivers up to 20 MIPS throughput at 20 MHz. The ATTINY13A-SF is designed for compact embedded systems where low cost, low power, and deterministic control are more important than memory capacity. A microcontroller is a programmable control component that combines a CPU core, nonvolatile program memory, working memory, and peripherals on one integrated circuit. The ATtiny13A belongs to the TinyAVR family and uses the AVR enhanced RISC architecture. Its instruction set executes most instructions in a single clock cycle, allowing clock speed to be balanced against power consumption in battery-operated equipment. The ATTINY13A-SF includes 90 powerful AVR instructions, eight general-purpose working registers, brown-out detection, power-on reset, a watchdog timer, and four 10-bit ADC channels. Its small memory footprint suits simple state machines, sensor interfaces, LED control, timers, and compact consumer accessories. The 20 MHz maximum clock provides additional timing margin for protocol handling and control loops. The ATtiny13A is based on low-power CMOS technology and is designed for both active and low-power operation. The manufacturer describes the picoPower architecture as a way to optimize power consumption while maintaining execution throughput. The 1.8 V to 5.5 V operating range permits operation from single-cell and low-voltage systems as well as conventional 3.3 V or 5 V rails. Typical applications include battery-powered sensors, simple LED and motor-control boards, compact remote controls, consumer appliances, hobby projects, and small embedded control modules. The ATTINY13A can be programmed through In-Circuit Serial Programming, while the MPLAB Snap debug interface supports in-circuit debugging through the device I/O and reset lines. When designing a board, verify the SOIC-8 footprint, pin 1 orientation, supply decoupling, programming access, and the voltage range of every connected peripheral. Use the manufacturer datasheet for the complete pin description, electrical characteristics, fuse settings, and recommended application circuits.

Permintaan RFG Kontak
ATTINY13A-SH - 8-Bit 20MHz AVR Microcontroller | Microchip
ATTINY13A-SH

ATTINY13A-SH - 8-Bit 20MHz AVR Microcontroller | Microchip

Microchip Technology ATTINY13A-SH is an 8-bit AVR tinyAVR microcontroller with a 20 MHz maximum clock, 1 KB in-system programmable Flash, 64 bytes EEPROM, and 64 bytes SRAM in an 8-pin SOIC package. The device provides 6 I/O ports and operates from low-voltage supplies identified in the verified data as 2.5 V, 3.3 V, and 5 V. According to the Microchip manufacturer datasheet, its enhanced RISC architecture executes powerful instructions in a single clock cycle, delivering throughput approaching 1 MIPS per MHz. An 8-bit microcontroller is a compact embedded-processing semiconductor that integrates a CPU core, program memory, data memory, I/O, and peripherals on one chip. The ATtiny13A belongs to the TinyAVR family and uses the AVR enhanced RISC architecture. Within the product hierarchy, it is an 8-bit RISC microcontroller, an embedded controller, and a semiconductor designed for cost-sensitive control tasks that require modest memory, limited I/O, and low power consumption. The primary features include 1 KB of Flash program memory, 64 bytes of EEPROM, 64 bytes of SRAM, 20 MHz operation, six I/O ports, and an AVR instruction set with 90 powerful instructions. The manufacturer describes most instructions as completing in a single clock cycle. These characteristics make the ATTINY13A-SH suitable for compact embedded controllers, simple timers, basic logic sequencers, small motor-control functions, and low-pin-count sensing systems where a larger MCU would add unnecessary cost and board area. Technically, the ATTINY13A combines a one-cycle-per-instruction AVR core with limited but deterministic resources. Its 1 KB Flash supports compact firmware, while the 64-byte SRAM and 64-byte EEPROM provide working and nonvolatile data storage. The device is offered in a surface-mount 8-SOIC package, allowing automated assembly and compact PCB placement. The verified distributor data identifies the device as active and lists it as an 8-bit AVR microcontroller with a 20 MHz clock. Typical applications include small appliance controls, sensor interfaces, LED-sequencing modules, compact motor controllers, battery-operated products, and simple industrial automation nodes. For these applications, the decisive benefits are the six available I/O ports, 1 KB program-memory capacity, low-voltage operation, and compact SOIC-8 footprint. A design requiring substantially more code space, RAM, peripheral capability, or pins should use a larger ATtiny or ATmega-class controller instead. A critical design consideration is to verify the complete operating-voltage envelope, clock configuration, reset behavior, and programming interface against the manufacturer datasheet before PCB release. Decoupling capacitors should be placed close to the supply pin, and unused inputs should be brought to a defined logic level. ISP programming should be exposed when firmware updates or production programming are required, rather than relying on an inaccessible programming interface. This page combines the verified manufacturer specifications, distributor availability, package details, sourcing information, and practical selection guidance with a strict analysis of same-footprint drop-in alternatives. It also distinguishes genuine drop-in options from unavailable or unverifiable replacements so engineers can evaluate migration risk before modifying a PCB.

Permintaan RFG Kontak
ATTINY13A-SN - 8-Bit 20MHz AVR Microcontroller | Microchip
ATTINY13A-SN

ATTINY13A-SN - 8-Bit 20MHz AVR Microcontroller | Microchip

Microchip Technology ATTINY13A-SN is a low-power 8-bit AVR RISC microcontroller with 1 KB of flash program memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a maximum clock frequency of 20 MHz, housed in an 8-pin SOIC package. The device operates from 1.8 V to 5.5 V and delivers up to 20 MIPS throughput at 20 MHz. An 8-bit microcontroller is a compact embedded-control device that combines a processor core, program memory, data memory, I/O ports, and peripherals on one semiconductor die. The ATtiny13A belongs to Microchip's tinyAVR family within the broader hierarchy of AVR embedded processors, 8-bit microcontrollers, and embedded systems. It is intended for control-intensive products where low cost, low power, and a small footprint matter more than instruction throughput or memory capacity. The ATTINY13A-SN integrates four 10-bit ADC channels with an AVR processor that executes most instructions in a single clock cycle. Its 20 MHz maximum operating frequency supports throughput approaching 1 MIPS per MHz. Program storage is organized as 1 KB of flash, while 64 bytes of EEPROM retain data without power and 64 bytes of SRAM support working memory. These resources make the device suitable for compact sensors, simple control loops, configuration tools, and low-pin-count embedded accessories. The 8-pin SOIC package exposes four I/O pins alongside power, ground, and reset. In-System Serial Programming and debug access can use the same reduced pin set used for the application. This is particularly useful for small production runs and prototypes because programming can be performed without removing the microcontroller from the circuit. The manufacturer product page identifies MPLAB Snap and a two-wire interface plus reset line as the supported debugging arrangement. Typical uses include battery-powered sensors, simple motor controls, LED indicators, compact timers, and embedded teaching projects. Because the ATTINY13A has limited flash and SRAM, applications requiring substantial buffering, protocol stacks, or simultaneous complex control tasks should use a larger AVR or another microcontroller family. The ATtiny13A's strengths are its low component count, simple toolchain, and broad operating range in a standard surface-mount package. When laying out a board, keep the decoupling capacitor close to VCC and GND, provide a clean reset path, and reserve the programming interface for ISP updates. Confirm the ADC reference and selected I/O pins against the design requirements. For new firmware, use the current AVR toolchain and verify timing, brown-out behavior, and unused-pin configuration in the final hardware. This product page combines the manufacturer's electrical and architectural specifications with practical programming, PCB-layout, and replacement guidance. It also identifies genuine same-footprint options for engineers who need a different delivery format while preserving the ATTINY13A design.

Permintaan RFG Kontak
ATTINY13A-SSU - 8-Bit AVR MCU, 1KB Flash, 20MHz | Microchip
ATTINY13A-SSU

ATTINY13A-SSU - 8-Bit AVR MCU, 1KB Flash, 20MHz | Microchip

The Microchip Technology ATTINY13A-SSU is an 8-bit AVR RISC-based microcontroller featuring 1 KB of in-system programmable Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a 4-channel 10-bit A/D converter, housed in an 8-pin SOIC (SO-8) package. The device operates across a 1.8 V to 5.5 V supply range and achieves up to 20 MIPS throughput at a 20 MHz clock, letting designers trade power consumption for processing speed on the fly. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile memory (Flash/ROM), volatile working memory (SRAM), and a configurable set of peripherals such as timers, ADCs, and digital I/O onto one IC. MCUs form the lowest tier of embedded computing, sitting beneath microprocessors (MPUs) and application processors in capability but above fixed-function logic ICs in flexibility. The AVR family places a RISC-style load/store CPU core next to tightly-coupled peripherals, and the tinyAVR sub-family scales this architecture into the smallest 8-pin parts for cost- and space-sensitive designs. Key features include hardware multipliers-free single-cycle execution, a debugWIRE on-chip debug interface, an analog comparator, a programmable watchdog timer with separate on-chip oscillator, and two PWM-capable 8-bit timers plus one high-speed timer. The picoPower technology extends battery life through multiple sleep modes that drop active current to the microamp range. Six general-purpose I/O lines are available on the SO-8 footprint, with PB5 serving as the reset pin and supporting in-circuit serial programming. Architecturally, the ATTINY13A-SSU fuses an enhanced RISC core (90+ instructions, most single-cycle) with a Harvard-style memory layout that lets the CPU fetch instructions from Flash while data accesses hit SRAM in the same cycle. The peripheral set is selected for analog and digital mixed-signal chores: a 10-bit successive-approximation ADC with four input channels, a programmable analog comparator, and dedicated timer/counter blocks with PWM output match units for switching tasks. Typical applications include LED drivers, battery chargers, small motor controls, remote control transmitters, simple sensor nodes, and wearable accessories where board area and quiescent current are constrained. The wide 1.8 V to 5.5 V range lets a single design migrate between single-cell lithium and 3.3 V or 5 V system rails without hardware changes. When laying out a board, place the decoupling capacitor (typically 100 nF) within a few millimetres of the VCC pin and route a low-impedance GND pour under the exposed copper area to keep digital switching noise out of the ADC inputs. Ensure the RESET pin (PB5) is pulled high through 10 kohm and accessible to the ISP header so in-circuit programming and debugWIRE debug sessions can be performed without removing the part. This page consolidates distributor pricing, drop-in alternatives, and engineering design notes that complement the manufacturer datasheet to accelerate part selection and PCB bring-up.

Permintaan RFG Kontak
ATTINY13A-SU - 20MHz 8-Bit AVR Microcontroller | Microchip
ATTINY13A-SU

ATTINY13A-SU - 20MHz 8-Bit AVR Microcontroller | Microchip

The Microchip Technology ATTINY13A-SU is a low-power 8-bit AVR microcontroller with a 20 MHz maximum clock, 1 KB of in-system programmable Flash memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a 4-channel 10-bit ADC, packaged in an 8-pin SOIC. It operates from 1.8 V to 5.5 V and can execute up to 20 MIPS at 20 MHz. An 8-bit microcontroller is a compact embedded-processing IC that combines a processor core, nonvolatile program memory, data memory, and peripherals on one die. The ATTINY13A belongs to the TinyAVR family within Microchip's AVR portfolio. Its enhanced RISC architecture executes many instructions in a single clock cycle, supporting processing throughput approaching 1 MIPS per MHz while allowing designs to balance speed against power consumption. The principal features of the ATTINY13A-SU include 1 KB of ISP Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and four 10-bit analog-to-digital converter channels. Its operating range of 1.8 V to 5.5 V supports low-voltage battery-powered equipment as well as conventional 5 V systems. In-system programming and ICSP interfaces support programming and debugging without removing the microcontroller from its circuit. The device uses the AVR enhanced RISC architecture and can reach 20 MIPS throughput at a 20 MHz clock. This processing rate is more than adequate for compact control tasks involving digital I/O, timing, simple control logic, and analog signal measurement. The ATtiny13A-SU combines this processing capability with a small memory footprint, making it suitable for cost- and power-sensitive embedded products rather than connectivity-heavy or high-memory applications. Typical uses include small motor controllers, temperature-sensor interfaces, battery monitors, LED controllers, appliance controls, hobby electronics, and simple sensor nodes. The four-channel 10-bit ADC is particularly useful when a design needs several analog inputs but does not require the memory, processing, or peripheral resources of a larger microcontroller family. For new layouts, preserve the ATtiny13A pin assignments and provide a decoupling capacitor close to VCC. Confirm the selected clock source, brown-out configuration, programming connector, and ADC reference arrangement against the manufacturer datasheet. Changes to package suffix, clock specification, or operating mode can alter qualification, programming, or temperature requirements even when the basic function remains the same. This product page consolidates the ATTINY13A-SU electrical characteristics, package information, pin assignments, lifecycle information, verified drop-in references, and practical design guidance. It supports engineers comparing the 8-pin SOIC implementation with documented alternatives without confusing electrical compatibility, package compatibility, and broader functional similarity.

Permintaan RFG Kontak
ATTINY13A-SUR - 20MHz 8-Bit AVR Microcontroller | Microchip (Tape & Reel)
ATTINY13A-SUR

ATTINY13A-SUR - 20MHz 8-Bit AVR Microcontroller | Microchip (Tape & Reel)

The Microchip Technology ATTINY13A-SUR is a low-power 8-bit AVR microcontroller with a 20 MHz maximum clock, 1 KB of in-system programmable Flash memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a 4-channel 10-bit ADC, packaged in an 8-pin SOIC. It operates from 1.8 V to 5.5 V and can execute up to 20 MIPS at 20 MHz. An 8-bit microcontroller is a compact embedded-processing IC that combines a processor core, nonvolatile program memory, data memory, and peripherals on one die. The ATTINY13A belongs to the TinyAVR family within Microchip's AVR portfolio. Its enhanced RISC architecture executes many instructions in a single clock cycle, supporting processing throughput approaching 1 MIPS per MHz while allowing designs to balance speed against power consumption. The principal features of the ATTINY13A-SUR include 1 KB of ISP Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and four 10-bit analog-to-digital converter channels. Its operating range of 1.8 V to 5.5 V supports low-voltage battery-powered equipment as well as conventional 5 V systems. In-system programming and ICSP interfaces support programming and debugging without removing the microcontroller from its circuit. The device uses the AVR enhanced RISC architecture and can reach 20 MIPS throughput at a 20 MHz clock. This processing rate is more than adequate for compact control tasks involving digital I/O, timing, simple control logic, and analog signal measurement. The ATtiny13A-SU combines this processing capability with a small memory footprint, making it suitable for cost- and power-sensitive embedded products rather than connectivity-heavy or high-memory applications. Typical uses include small motor controllers, temperature-sensor interfaces, battery monitors, LED controllers, appliance controls, hobby electronics, and simple sensor nodes. The four-channel 10-bit ADC is particularly useful when a design needs several analog inputs but does not require the memory, processing, or peripheral resources of a larger microcontroller family. For new layouts, preserve the ATtiny13A pin assignments and provide a decoupling capacitor close to VCC. Confirm the selected clock source, brown-out configuration, programming connector, and ADC reference arrangement against the manufacturer datasheet. Changes to package suffix, clock specification, or operating mode can alter qualification, programming, or temperature requirements even when the basic function remains the same. This product page consolidates the ATTINY13A-SUR electrical characteristics, package information, pin assignments, lifecycle information, verified drop-in references, and practical design guidance. It supports engineers comparing the 8-pin SOIC implementation with documented alternatives without confusing electrical compatibility, package compatibility, and broader functional similarity.

Permintaan RFG Kontak
ATTINY13V-10 - 10MHz AVR MCU with 1KB Flash | Microchip
ATTINY13V-10

ATTINY13V-10 - 10MHz AVR MCU with 1KB Flash | Microchip

The Microchip Technology ATTINY13V-10 is an 8-bit AVR RISC microcontroller rated for 10MHz operation, with 1KB of in-system programmable Flash, 64B of SRAM, 64B of EEPROM, six general-purpose I/O lines, and a 4-channel 10-bit ADC. It is represented in an 8-pin SOIC package for the ATTINY13V-10SU ordering option, making it suitable for compact embedded-control and analog-sensing designs. An 8-bit AVR microcontroller is a low-cost microcontroller architecture that combines a RISC processor core, Flash program memory, data SRAM, EEPROM, timers, interrupt handling, and configurable I/O on one integrated circuit. The ATtiny13 belongs to the AVR family and is positioned for simple control tasks where a small program and memory footprint are more valuable than extensive connectivity. Its analog converter also allows selected digital pins to measure external voltage-based sensor signals. Key features include 1KB of In-System Programmable Flash for firmware, 64B of SRAM for working data, and 64B of EEPROM for nonvolatile parameter retention. The device provides 32 general-purpose working registers, one 8-bit timer/counter with compare modes, internal and external interrupts, a programmable watchdog timer, and a four-channel 10-bit ADC. These resources support compact control loops, button and switch logic, simple actuator timing, and basic analog measurements. The 10MHz operating point provides a practical balance between processing throughput and power consumption. The manufacturer describes the ATtiny13 family as capable of throughput up to 20 MIPS at 20MHz, while the ATTINY13V-10 suffix denotes the 10MHz version. In-System Programming allows firmware to be programmed without removing the device from its circuit, and the watchdog timer supports recovery from stalled software loops in unattended embedded equipment. Typical uses include battery-powered sensor nodes, simple motor or relay controllers, LED status indicators, panel-button interfaces, compact timers, and low-cost analog monitoring products. The 4-channel ADC can evaluate resistive sensor networks when their outputs remain within the device's supported input range. The six I/O lines are sufficient for small control systems where LEDs, switches, transistors, or a communication interface can be multiplexed around the controller. PCB design should preserve clean analog grounds near the ADC-capable pins, route the supply and ground connections directly to the device pins, and place its decoupling capacitor close to VCC. Firmware must also account for the small 64B SRAM allocation, use EEPROM writes sparingly for endurance, and configure the watchdog deliberately. The clock speed suffix should be selected according to the product's timing, power, and qualification requirements rather than treated as interchangeable without review. This product page combines the manufacturer's core specifications with package-specific sourcing information, practical design guidance, compatible ordering options, and a parameter-focused comparison. This engineering context helps distinguish the base ATTINY13V-10 device from its package and ordering-code variants before schematic capture and PCB release.

Permintaan RFG Kontak
ATTINY1607-MN - 20MHz 16KB AVR MCU | Microchip
ATTINY1607-MN

ATTINY1607-MN - 20MHz 16KB AVR MCU | Microchip

The Microchip Technology ATTINY1607-MN is an 8-bit AVR tinyAVR microcontroller operating at up to 20 MHz, with 16 KB of Flash memory, 1 KB of SRAM, 256 bytes of EEPROM, and a 24-pin VQFN 4 x 4 mm package. The device combines a hardware-multiplier AVR processor with integrated analog, event-system, and low-power peripherals for compact embedded-control designs. A microcontroller is an integrated circuit containing a processor core, program memory, data memory, and peripherals on one semiconductor die. The ATTINY1607 belongs to the AVR -> tinyAVR -> 8-bit RISC microcontroller hierarchy. It executes firmware locally rather than relying on a host processor, allowing compact products to perform sensing, control, communications, and actuator management with fewer external components. The principal device characteristics include a 20 MHz maximum clock, 16 KB Flash, 1 KB SRAM, and 256 bytes of EEPROM. Its 1.8 V to 5.5 V operating range supports both low-voltage and conventional 5 V embedded systems. The package also provides 24 electrical positions in a compact 4 x 4 mm footprint, reducing board area where space is constrained. The device supports modern tinyAVR integration techniques identified by Microchip, including the Event System, SleepWalking functionality, accurate analog features, and advanced peripherals. Event-driven operation can reduce unnecessary processor activity, while SleepWalking allows selected peripheral functions to continue during low-power states. The hardware multiplier improves the execution efficiency of compact multiplication and scaling operations. Typical uses include closed-loop industrial control, compact sensor nodes, motor and actuator controllers, and low-power embedded products. The 16 KB Flash capacity accommodates application firmware and configuration logic, while 1 KB of SRAM supports working variables and peripheral buffering. The integrated analog and communication functions reduce the component count of small control boards. PCB design should preserve short, controlled analog and digital paths, provide stable supply decoupling, and route clock-sensitive signals away from high-current switching nodes. Firmware and peripheral configuration should be checked against the manufacturer pin-description and peripheral tables because reuse of a footprint does not automatically guarantee identical signal functions. This product record combines the manufacturer specifications, exact-package ordering information, sourcing guidance, compatible family candidates, and practical design considerations for engineers evaluating the ATTINY1607-MN in compact low-power embedded systems.

Permintaan RFG Kontak
ATTINY1624-SSU - 8-Bit AVR tinyAVR 2 MCU 20MHz 16KB Flash SOIC-14 | Microchip
ATTINY1624-SSU

ATTINY1624-SSU - 8-Bit AVR tinyAVR 2 MCU 20MHz 16KB Flash SOIC-14 | Microchip

The Microchip Technology ATTINY1624-SSU is an 8-bit AVR RISC microcontroller from the tinyAVR 2 family, featuring a hardware multiplier, 20 MHz maximum CPU clock, 16 KB in-system programmable Flash, 2 KB SRAM and 256 bytes of EEPROM, all housed in a 14-pin narrow-body SOIC package rated for industrial temperature (-40C to +85C). The device integrates the modern AVR CPU core with Core Independent Peripherals (CIPs) including event system, configurable custom logic, and 12-bit differential ADC with Programmable Gain Amplifier, enabling mixed-signal designs without external components. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for low-cost, low-power deterministic embedded control. Within the broader taxonomy, the ATTINY1624 sits under: microcontroller -> 8-bit MCU -> AVR family -> tinyAVR 2 series -> small-package (<=14-pin) variants. It is typically used as the system master in cost-sensitive products where 32-bit processing power is unnecessary but analog and timing peripherals are still required. Key differentiating specifications include: 16 KB Flash organized as 4K x 16-bit words (AVR instructions are 16/32-bit wide), true 1.8V-5.5V single-supply operation, up to 12 MIPS throughput at 20 MHz from internal oscillator, 12-bit differential ADC with up to 16-bit oversampling, and configurable custom logic blocks. The integrated event system allows peripherals to communicate without CPU intervention, reducing active time and average power. Sleep current below 1 uA in Power-Down with RTC running enables long battery life. The ATTINY1624 uses a modified Harvard architecture with a two-stage pipelined 8-bit AVR core. Flash is read in 16-bit words so 16 KB of Flash stores 8K instructions. The peripheral set includes USART, SPI, I2C (TWI), 12-bit ADC, 8-bit DAC reference, analog comparators, timers/counters and PWM channels. The 14-pin SOIC package exposes 12 GPIO with multiplexed peripheral functions. Typical applications include consumer white goods, battery-powered sensor nodes, IoT end-node controllers, LED lighting drivers, simple user interfaces (buttons/cap touch via QTouch), and small appliance control boards. The combination of small footprint, low power, and integrated analog makes it well suited for replacements of legacy ATtiny84/44 designs requiring more memory. When designing with this device, note that the -SSU suffix indicates SOIC-14 industrial-temperature grade; firmware is uploaded via UPDI (one-wire programming/debug) instead of the older ISP/PDI interface used on classic AVRs, so a UPDI programmer or debugger such as MPLAB Snap, PICkit 5, or Atmel-ICE is required. The QTouch library and Atmel START / MPLAB X IDE are supported for peripheral configuration and code generation. This page synthesizes current distributor pricing, drop-in alternatives in the same SOIC-14 footprint, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
ATTINY1626-SU - 20MHz AVR MCU, 16KB Flash | Microchip
ATTINY1626-SU

ATTINY1626-SU - 20MHz AVR MCU, 16KB Flash | Microchip

The Microchip Technology ATTINY1626-SU is an 8-bit AVR tinyAVR 2 microcontroller operating up to 20 MHz, with 16 KB Flash memory, 2 KB SRAM, and 256 bytes of EEPROM in a 20-pin SOIC package. The device integrates I2C, SPI, and UART/USART connectivity, together with analog and configurable custom logic peripherals for compact embedded-control designs. An 8-bit microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The ATTINY1626 belongs to the tinyAVR 2 family, where the AVR CPU and hardware multiplier execute compact control code while serial interfaces and event-driven peripherals reduce the need for additional discrete components. Its position within the broader hierarchy is microcontroller IC, embedded processor, and general-purpose semiconductor. Key device resources include a 20 MHz maximum clock rate, 16 KB of program Flash, 2 KB of SRAM, and 256 bytes of nonvolatile EEPROM. The 20-pin SOIC package supports digital I/O, communication interfaces, and analog measurement functions. This combination makes the part appropriate for compact industrial controls, sensor nodes, embedded instruments, and connected peripheral designs where board area and peripheral integration are important. The tinyAVR 2 architecture combines the AVR CPU with hardware multiplier support, Event System functionality, advanced digital peripherals, and configurable custom logic. The integrated peripherals allow software to coordinate peripheral events without excessive polling, while the hardware multiplier accelerates suitable arithmetic operations. Compared with a larger general-purpose MCU, the ATTINY1626 offers a focused resource set in a smaller 20-pin footprint. Typical applications include building controls, compact motor controllers, battery-powered sensor interfaces, serial bridges, programmable logic controllers, and small laboratory instruments. I2C and SPI support allow connection to sensors, memories, and display or communication modules, while UART/USART provides a straightforward path to host controllers. Designers should match peripheral assignments, package pins, voltage limits, and clock requirements before finalizing a PCB layout. Place decoupling capacitors close to the supply and ground pins, route high-current and sensitive analog paths deliberately, and confirm the selected external clock or internal oscillator configuration in the manufacturer datasheet. Adequate flash and SRAM headroom is essential when adding protocol libraries, bootloader functions, or event-heavy control logic. This product record combines the manufacturer device information with component-level comparison, sourcing guidance, and practical design considerations. It also identifies verified drop-in candidates while distinguishing genuine same-package options from relatives that require a different footprint or package.

Permintaan RFG Kontak
ATTINY1626-XF - 20MHz AVR Microcontroller | Microchip Technology
ATTINY1626-XF

ATTINY1626-XF - 20MHz AVR Microcontroller | Microchip Technology

The Microchip Technology ATTINY1626-XF is an 8-bit AVR tinyAVR 2 microcontroller with a 20 MHz maximum clock, 16 KB of Flash memory, 2 KB of SRAM, and 256 bytes of EEPROM in a 20-pin SSOP package. It operates from 1.8 V to 5.5 V and is specified for industrial operation up to 125°C. The device combines an AVR CPU with a hardware multiplier, an Event System, and accurate analog peripherals including a 12-bit differential ADC with Programmable Gain Amplifier. An AVR microcontroller is an embedded semiconductor that integrates a processor core, program memory, data memory, and peripherals into one compact device. The tinyAVR 2 family occupies the small-footprint end of the Microchip AVR portfolio, where the ATTINY1626 provides more memory, timing resources, and analog capability than a basic 8-bit controller while remaining suitable for compact control systems. Core features include 20 MHz operation, 16 KB of Flash for firmware, 2 KB of SRAM for working data, and 256 bytes of nonvolatile EEPROM. The 12-bit differential ADC and Programmable Gain Amplifier support measurements from low-level sensors, while the hardware multiplier accelerates suitable multiplication operations. The Event System enables deterministic peripheral signaling and reduces reliance on software polling. The ATTINY1626 uses the AVR CPU architecture and supports peripheral resources associated with the tinyAVR 2 family. Its 20-pin SSOP construction offers a practical balance between board area and available I/O. The 1.8 V to 5.5 V operating range permits use across low-voltage and conventional supply systems, while the -40°C to 125°C industrial temperature range supports demanding ambient environments. Typical uses include compact industrial control modules, sensor-interface nodes, programmable timers, monitoring equipment, building controls, and low-power consumer devices. The differential ADC and PGA are particularly useful when a design must acquire small analog signals without relying on a separate converter. The Event System can coordinate timing-sensitive internal functions where deterministic interrupt-driven behavior is preferred. When designing a board, follow the manufacturer pin-description and decoupling guidance in data sheet DS40002234B. Preserve the SSOP-20 land pattern, route sensitive analog inputs away from fast-switching nodes, and provide local supply bypassing. Confirm the programmed clock, peripheral pins, and package orientation before releasing a PCB because migrating among tinyAVR 2 devices can alter the available pin count even when code remains compatible. This page combines the manufacturer specifications, practical application guidance, package details, sourcing information, and verified drop-in comparison options. It also identifies the limits of direct substitution, helping engineers distinguish electrically similar devices from parts that can replace ATTINY1626-XF without changing the PCB.

Permintaan RFG Kontak
ATTINY1626-XU - 20MHz 16KB AVR tinyAVR 2 MCU | Microchip
ATTINY1626-XU

ATTINY1626-XU - 20MHz 16KB AVR tinyAVR 2 MCU | Microchip

The Microchip Technology ATTINY1626-XU is an 8-bit AVR RISC microcontroller from the tinyAVR 2 family, delivering up to 20 MHz CPU performance with a hardware multiplier, 16 KB of Flash program memory, 2 KB of SRAM, and 256 bytes of EEPROM in a 20-pin SSOP industrial-grade package rated for -40C to +85C operation. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals around an 8-bit data bus. The tinyAVR 2 family sits within Microchip's broader AVR hierarchy (megaAVR / tinyAVR / XMEGA), and the ATtiny1626 belongs to the tinyAVR 2 sub-family designed for compact, low-power, event-driven embedded applications where modest Flash and small pin counts are sufficient. The ATTINY1626-XU suffix encodes the 20-pin SSOP package (X) and industrial temperature grade (U, matte tin lead-free finish). Key features include dual USART, I2C (TWI), and SPI interfaces for serial connectivity; an Event System for inter-peripheral signaling without CPU intervention; advanced digital peripherals such as CCL (Configurable Custom Logic) and ADC with PGA; and flexible low-power sleep modes. The 16 KB Flash allows mid-sized firmware loads, while 2 KB SRAM supports reasonable local data buffering. Operating voltage ranges from 1.8V to 5.5V, enabling direct connection to coin-cell, Li-ion, or 3.3V/5V rails without level translation. Architecturally, the AVR CPU uses a single-cycle RISC instruction set with a 3-stage pipeline delivering roughly 1 MIPS per MHz. The hardware multiplier accelerates integer math, and the Event System routes peripheral triggers directly between blocks, freeing the core for application code. Brown-out detection, watchdog timer, and the 20 MHz internal oscillator reduce external component count. Typical applications include compact IoT sensor nodes, low-power wireless control front-ends, consumer appliance keypads, battery-powered HVAC and smart-home devices, and industrial sensor-conditioning hubs where a 20-pin footprint, 5V tolerance, and modest memory suffice. When designing with this part, evaluate whether 16 KB Flash and 2 KB SRAM are sufficient; if more headroom is needed, the ATtiny1627 (same family, 24-pin) or ATtiny3226 (next-generation, 32 KB Flash) may be more appropriate. Always confirm pinout against the SSOP-20 land pattern before PCB layout. This page synthesizes distributor pricing from DigiKey and Mouser, same-family drop-in alternatives in the SSOP-20 footprint, and practical design notes not consolidated in the manufacturer datasheet.

Permintaan RFG Kontak
ATTINY1634-MN - 12MHz 8-bit AVR 16KB MCU | Microchip Technology
ATTINY1634-MN

ATTINY1634-MN - 12MHz 8-bit AVR 16KB MCU | Microchip Technology

The Microchip Technology ATTINY1634-MN is a low-power CMOS 8-bit AVR microcontroller based on the AVR enhanced RISC architecture, operating at up to 12 MHz with 16 KB of Flash memory in a 20-QFN exposed-pad package. It combines 16K x 8 Flash, 256 B EEPROM, 1 KB SRAM and 18 general-purpose I/O lines in a compact 4 x 4 mm surface-mount package. An 8-bit AVR microcontroller is a compact embedded-control device that executes instructions using an enhanced RISC core, typically approaching 1 MIPS per MHz. The ATtiny family sits within the broader hierarchy of embedded processors, microcontrollers, embedded controllers and semiconductors. The ATTINY1634 is designed for low-power control tasks where local processing, serial communication, timing and mixed-signal control are needed without a high-cost MCU platform. Key device capabilities include a 12 MHz maximum clock, 16 KB Flash, 256 B EEPROM, 1 KB SRAM, 18 general-purpose I/O lines, 32 general-purpose working registers, one 8-bit timer/counter, one 16-bit timer/counter, two full-duplex USARTs with Start Frame Detection, a Universal Serial Interface, I2C slave support and internal and external interrupts. These resources make the MCU suitable for compact control boards, industrial modules and embedded peripherals. The AVR enhanced RISC architecture provides an instruction-oriented balance between processing throughput and power efficiency. At the rated 12 MHz operating point, the architecture can approach 1 MIPS, while the low-power CMOS design supports applications that alternate between active processing and reduced-power operating states. The combination of dual USARTs, USI and I2C allows the device to bridge several common embedded serial interfaces without requiring large numbers of external peripheral ICs. Typical uses include industrial sensing and control, compact serial gateways, sensor-hub controllers, battery-powered instrumentation, communication modules and small automation nodes. Its 18 I/O lines also permit direct interface connections to sensors, displays, relays and digital logic. The 20-QFN exposed-pad package supports dense PCB layouts, although careful thermal-pad soldering and layout practices are important for reliable assembly. Designers should verify the complete pin-assignment table in the manufacturer datasheet before routing the PCB, particularly for the exposed pad, power pins, reset and communications functions. Decoupling requirements, clock stability, programming access, I2C address configuration and USART logic levels should also be checked against the device documentation and the selected operating voltage. This product page consolidates the exact ATTINY1634-MN technical identity, verified listing information, package details and engineering guidance into one focused reference for embedded-system design.

Permintaan RFG Kontak