5M570ZT100C5 - MAX V CPLD, 440 LEs, 74 I/O, TQFP-100 | Intel
MPN: 5M570ZT100C5 ✓ Aktif5M570ZT100C5 Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic IC that sits between simple PLDs/SPLDs and high-density FPGAs in the programmable-logic taxonomy: SPLD -> CPLD -> FPGA & CPLD -> programmable logic -> digital IC. MAX V CPLDs use a low-power, instant-on, flash-based architecture, which means designs power up in a known working state without an external boot PROM and consume very little quiescent current. This makes them ideal for I/O expansion, bus bridging, and power-sequencing glue logic.
Key features include 440 Logic Elements (approximately 440 macro cells in the MAX V family), 74 user I/O pins distributed across multiple I/O banks, an internal frequency rating of 118.3 MHz with fMAX up to 184 MHz, propagation delay of 9.5 ns, in-system programmability via JTAG (IEEE 1149.1), and support for multiple I/O standards (LVCMOS, LVTTL, PCI). The device operates from a single 1.8 V core supply with separate VCCIO banks for I/O voltage flexibility (1.2 V to 3.3 V).
Architecturally, MAX V CPLDs use a non-volatile flash configuration cell that eliminates the external configuration memory required by SRAM-based FPGAs, providing instant-on behavior. The MultiVolt core allows designers to interface 1.8 V logic to 3.3 V, 2.5 V, or 1.8 V peripherals without level shifters. The flash-based design also enables bit-stream security and zero inrush current during configuration, which is a key differentiator versus SRAM FPGAs.
Typical applications include I/O expansion and bus bridging in industrial control systems, power-up sequencing for FPGAs and processors, interface translation (LVCMOS/PCI/LVTTL), address decoding in legacy microcontrollers, and glue logic replacement. The instant-on feature is particularly valuable in motor control, automotive body electronics, and any application requiring deterministic power-up behavior.
When designing with the 5M570ZT100C5, connect all VCCINT and VCCIO pins and provide a 0.1 uF decoupling capacitor close to each supply pin. The JTAG pins TMS, TDI, TDO, and TCK support most I/O standards except PCI and 1.2 V LVCMOS. Unused pins can be left floating or tied to a defined level per JTAG chain design rules.
This page synthesizes distributor pricing, pin-compatible MAX V family alternatives, and practical design notes (decoupling, JTAG chain, thermal limits) not found in the manufacturer datasheet alone.
Alternatif penggantian untuk 5M570ZT100C5 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian 5M570ZT100C5 (sama faktor bentuk dan footprint) — berbeda di dalam Package, Programming Interface, Configuration Memory, User Flash Memory, I/O Supply Voltage (VCCIO).
5M570ZT100C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZT100C4N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZT100A5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZM100C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZM100C4N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZM100A5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZT100C5 Rating Maksimal & Karakteristik Listrik
| Device Family | MAX V |
| Logic Elements (LEs) | 440 |
| Macro Cells | 440 |
| User I/O Pins | 74 |
| Maximum Internal Frequency | 118.3 MHz |
| Maximum fMAX (internal) | 184 MHz |
| Propagation Delay (tPD) | 9.5 ns |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Supply Voltage (VCCIO) | 1.2 V to 3.3 V |
| Paket | TQFP-100 (16 x 16 mm, 0.5 mm pitch) |
| Configuration Technology | Non-volatile flash |
| Programming Interface | JTAG (IEEE 1149.1) |
| Operating Temperature (Commercial) | 0C to +85C |
| Status RoHS | Compliant |
| Tipe Mounting | Surface Mount |
| Level MSL | 3 (168 hours) |
Konfigurasi Pin 5M570ZT100C5
| Pin produk 1 | GND — Ground |
| Pin produk 2 | I/O — User I/O pin (Bank 1) |
| Pin produk 3 | I/O — User I/O pin (Bank 1) |
| Pin produk 4 | I/O — User I/O pin (Bank 1) |
| Pin produk 5 | I/O — User I/O pin (Bank 1) |
| Pin produk 6 | I/O — User I/O pin (Bank 1) |
| Pin produk 7 | I/O — User I/O pin (Bank 1) |
| Pin produk 8 | I/O — User I/O pin (Bank 1) |
| Pin produk 9 | I/O — User I/O pin (Bank 1) |
| Pin produk 10 | I/O — User I/O pin (Bank 1) |
| Pin produk 11 | VCCIO1 — Bank 1 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 12 | I/O — User I/O pin (Bank 1) |
| Pin produk 13 | I/O — User I/O pin (Bank 1) |
| Pin produk 14 | I/O — User I/O pin (Bank 1) |
| Pin produk 15 | I/O — User I/O pin (Bank 1) |
| Pin produk 16 | I/O — User I/O pin (Bank 1) |
| Pin produk 17 | I/O — User I/O pin (Bank 1) |
| Pin produk 18 | I/O — User I/O pin (Bank 1) |
| Pin produk 19 | I/O — User I/O pin (Bank 1) |
| Pin produk 20 | I/O — User I/O pin (Bank 1) |
| Pin produk 21 | I/O — User I/O pin (Bank 1) |
| Pin produk 22 | VCCIO1 — Bank 1 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 23 | I/O — User I/O pin (Bank 1) |
| Pin produk 24 | I/O — User I/O pin (Bank 1) |
| Pin produk 25 | I/O — User I/O pin (Bank 1) |
| Pin produk 26 | TDI — JTAG Test Data In (Bank 1) |
| Pin produk 27 | TMS — JTAG Test Mode Select (Bank 1) |
| Pin produk 28 | TCK — JTAG Test Clock (Bank 1) |
| Pin produk 29 | I/O — User I/O pin (Bank 1) |
| Pin produk 30 | VCCINT — Core supply voltage (1.8 V) |
| Pin produk 31 | GND — Ground |
| Pin produk 32 | I/O — User I/O pin (Bank 2) |
| Pin produk 33 | I/O — User I/O pin (Bank 2) |
| Pin produk 34 | I/O — User I/O pin (Bank 2) |
| Pin produk 35 | I/O — User I/O pin (Bank 2) |
| Pin produk 36 | I/O — User I/O pin (Bank 2) |
| Pin produk 37 | I/O — User I/O pin (Bank 2) |
| Pin produk 38 | VCCIO2 — Bank 2 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 39 | I/O — User I/O pin (Bank 2) |
| Pin produk 40 | I/O — User I/O pin (Bank 2) |
| Pin produk 41 | I/O — User I/O pin (Bank 2) |
| Pin produk 42 | I/O — User I/O pin (Bank 2) |
| Pin produk 43 | I/O — User I/O pin (Bank 2) |
| Pin produk 44 | I/O — User I/O pin (Bank 2) |
| Pin produk 45 | I/O — User I/O pin (Bank 2) |
| Pin produk 46 | I/O — User I/O pin (Bank 2) |
| Pin produk 47 | I/O — User I/O pin (Bank 2) |
| Pin produk 48 | I/O — User I/O pin (Bank 2) |
| Pin produk 49 | I/O — User I/O pin (Bank 2) |
| Pin produk 50 | I/O — User I/O pin (Bank 2) |
| Pin produk 51 | I/O — User I/O pin (Bank 2) |
| Pin produk 52 | VCCIO2 — Bank 2 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 53 | I/O — User I/O pin (Bank 2) |
| Pin produk 54 | I/O — User I/O pin (Bank 2) |
| Pin produk 55 | I/O — User I/O pin (Bank 2) |
| Pin produk 56 | I/O — User I/O pin (Bank 2) |
| Pin produk 57 | I/O — User I/O pin (Bank 2) |
| Pin produk 58 | I/O — User I/O pin (Bank 2) |
| Pin produk 59 | GND — Ground |
| Pin produk 60 | I/O — User I/O pin (Bank 3) |
| Pin produk 61 | I/O — User I/O pin (Bank 3) |
| Pin produk 62 | I/O — User I/O pin (Bank 3) |
| Pin produk 63 | VCCIO3 — Bank 3 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 64 | I/O — User I/O pin (Bank 3) |
| Pin produk 65 | I/O — User I/O pin (Bank 3) |
| Pin produk 66 | I/O — User I/O pin (Bank 3) |
| Pin produk 67 | I/O — User I/O pin (Bank 3) |
| Pin produk 68 | I/O — User I/O pin (Bank 3) |
| Pin produk 69 | I/O — User I/O pin (Bank 3) |
| Pin produk 70 | I/O — User I/O pin (Bank 3) |
| Pin produk 71 | I/O — User I/O pin (Bank 3) |
| Pin produk 72 | I/O — User I/O pin (Bank 3) |
| Pin produk 73 | I/O — User I/O pin (Bank 3) |
| Pin produk 74 | VCCIO3 — Bank 3 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 75 | I/O — User I/O pin (Bank 3) |
| Pin produk 76 | I/O — User I/O pin (Bank 3) |
| Pin produk 77 | I/O — User I/O pin (Bank 3) |
| Pin produk 78 | I/O — User I/O pin (Bank 3) |
| Pin produk 79 | I/O — User I/O pin (Bank 3) |
| Pin produk 80 | I/O — User I/O pin (Bank 3) |
| Pin produk 81 | I/O — User I/O pin (Bank 3) |
| Pin produk 82 | I/O — User I/O pin (Bank 3) |
| Pin produk 83 | I/O — User I/O pin (Bank 3) |
| Pin produk 84 | VCCIO3 — Bank 3 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 85 | I/O — User I/O pin (Bank 3) |
| Pin produk 86 | I/O — User I/O pin (Bank 3) |
| Pin produk 87 | I/O — User I/O pin (Bank 3) |
| Pin produk 88 | I/O — User I/O pin (Bank 3) |
| Pin produk 89 | I/O — User I/O pin (Bank 3) |
| Pin produk 90 | GND — Ground |
| Pin produk 91 | I/O — User I/O pin (Bank 4) |
| Pin produk 92 | I/O — User I/O pin (Bank 4) |
| Pin produk 93 | I/O — User I/O pin (Bank 4) |
| Pin produk 94 | I/O — User I/O pin (Bank 4) |
| Pin produk 95 | VCCIO4 — Bank 4 I/O supply voltage (1.2 V to 3.3 V) |
| Pin produk 96 | I/O — User I/O pin (Bank 4) |
| Pin produk 97 | I/O — User I/O pin (Bank 4) |
| Pin produk 98 | I/O — User I/O pin (Bank 4) |
| Pin produk 99 | I/O — User I/O pin (Bank 4) |
| Pin produk 100 | TDO — JTAG Test Data Out (Bank 1) |
Aplikasi Umum
5M570ZT100C5 cocok untuk 7 aplikasis: I/O Expansion and Bus Bridging, Power-Up Sequencing for Processors and FPGAs, Interface Translation (LVCMOS / LVTTL / PCI), Address Decoding and Chip-Select Generation, Industrial Motor Control Glue Logic, Legacy Microcontroller Expansion, FPGA Configuration and JTAG Chain Management.
I/O Expansion and Bus Bridging
The 5M570ZT100C5 fits I/O expansion and bus bridging applications because it provides 74 user I/Os across multiple VCCIO banks, each programmable from 1.2 V to 3.3 V, allowing a single CPLD to bridge between 3.3 V microcontrollers and 1.8 V peripherals without external level shifters. The 440 Logic Elements and 9.5 ns propagation delay are sufficient for address decoding, chip-select generation, and asynchronous bus arbitration at sub-100 MHz rates. Compared with discrete 74-series glue logic, the 5M570ZT100C5 replaces dozens of packages with one instant-on, non-volatile device that boots into a known working state, eliminating external boot PROMs required by SRAM FPGAs.
Direkomendasikan
Power-Up Sequencing for Processors and FPGAs
The 5M570ZT100C5 is ideal for power-up sequencing because its non-volatile flash configuration powers up into a known working state in microseconds, well before the processor or SRAM-based FPGA finishes its boot cycle. The 440 Logic Elements and 74 user I/Os are sufficient to sequence 6 to 8 power rails with adjustable delay chains, monitor PG (power-good) signals, and assert reset to downstream devices. Compared with sequencer ICs and discrete RC delay circuits, the CPLD approach provides field-upgradeable sequencing logic via JTAG, eliminating rework when rail order changes. The 1.8 V core operates from the same rail that it may be sequencing.
Direkomendasikan
Interface Translation (LVCMOS / LVTTL / PCI)
The 5M570ZT100C5 supports multi-standard I/O translation because each I/O bank has an independent VCCIO supply programmable from 1.2 V to 3.3 V, and individual pins can be set to LVCMOS, LVTTL, or PCI input/output levels. This makes the device well suited as a level shifter between legacy 5 V-tolerant 3.3 V peripherals (via PCI-compatible Bank 1 inputs) and modern 1.8 V processors. The 118.3 MHz internal frequency and 9.5 ns propagation delay comfortably handle 33 MHz PCI and 50 MHz LVDS-style interfaces with adequate timing margin. Compared with dedicated level-shifter ICs, the CPLD adds configurable logic for protocol conversion alongside the voltage translation.
Direkomendasikan
Address Decoding and Chip-Select Generation
The 5M570ZT100C5 fits address decoding because its 440 Logic Elements and 9.5 ns propagation delay generate multiple chip-select, chip-enable, and read/write strobes from a single address bus. With 74 user I/Os, the device can decode up to 8 bank-select lines plus 24 address lines, comfortably handling legacy 16-bit and 32-bit microcontroller memory maps. The instant-on flash configuration means decoded outputs are stable at power-up, eliminating bus-contention glitches during boot. Compared with discrete 74HC138 / 74HC139 decoders, the 5M570ZT100C5 replaces 4 to 6 packages and supports in-system reprogramming for memory-map updates.
Direkomendasikan
Industrial Motor Control Glue Logic
The 5M570ZT100C5 fits industrial motor control applications because its non-volatile flash configuration provides deterministic, instant-on behavior required for safety-critical PWM gating, encoder processing, and fault-interlock logic. The 74 user I/Os comfortably handle 3-phase gate-driver enable signals, Hall-sensor inputs, and PWM feedback paths. Operating temperature of 0C to +85C covers most factory-floor enclosures; for harsher environments choose the I7N industrial-grade variant. Compared with microcontrollers, the CPLD adds zero software overhead, deterministic latency, and immunity to firmware lockup in safety circuits.
Direkomendasikan
Legacy Microcontroller Expansion
The 5M570ZT100C5 expands legacy microcontrollers that lack sufficient I/O by offloading glue logic from software to hardware. The 74 user I/Os and 440 Logic Elements comfortably handle matrix-keypad scanning, 7-segment multiplexing, LCD bias generation, and UART bit-banging replacement. The JTAG (IEEE 1149.1) programming interface allows in-system firmware updates via the same JTAG chain used for boundary-scan testing. Compared with discrete 74LS-series logic, the CPLD reduces board area by 60 to 70 percent, improves reliability by removing solder joints, and adds in-system reprogrammability for late-stage design changes.
Direkomendasikan
FPGA Configuration and JTAG Chain Management
The 5M570ZT100C5 fits FPGA configuration-management applications where multiple SRAM FPGAs need to be daisy-chained, programmed in parallel, or reconfigured based on board-revision strapping. The 74 user I/Os and 440 Logic Elements implement JTAG fan-out, revision-detect GPIO decoding, and parallel-configuration fan-out without consuming FPGA general-purpose I/O. The non-volatile flash storage holds the FPGA bitstream version-select logic, enabling automatic revision matching at power-up. Compared with discrete JTAG buffers and EEPROMs, the CPLD approach simplifies board layout and supports field updates of the revision logic.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk 5M570ZT100C5 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | 5M570ZT100C5N | 5M570ZT100C4N | 5M570ZT100A5N | 5M570ZM100C5N | 5M570ZM100C4N | 5M570ZM100A5N |
|---|---|---|---|---|---|---|---|
| Package | TQFP-100 (16x16 mm) | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) |
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Logic Elements | 440 | 440 | 440 | 440 | 440 | 440 | 440 |
| User I/Os | 74 | 74 | 74 | 74 | 74 | 74 | 74 |
| Speed Grade | C5 | C5 | C4 | A5 | C5 | C4 | A5 |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Configuration Technology | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash |
| Family | MAX V | MAX V | MAX V | MAX V | MAX V | MAX V | MAX V |
Diferensiator Kunci
- C5 speed grade offers tighter timing margin than C4/A5 (vs5M570ZT100C4N)
- Non-volatile flash configuration enables instant-on operation (vs5M570ZT100A5N)
- MultiVolt I/O banks support independent 1.2 V to 3.3 V rails per bank (vs5M570ZM100C5N)
Catatan Desain
Connect all VCCINT and VCCIO pins to their respective supplies even if some I/O banks are unused. Place a 0.1 uF ceramic decoupling capacitor within 100 mils of each VCCINT and VCCIO pin, and add a bulk 10 uF tantalum or ceramic capacitor near the package. The MultiVolt I/O architecture lets each bank operate independently at 1.2 V to 3.3 V, but unused VCCIO pins must still be tied to a valid rail per Altera MAX V datasheet recommendations to avoid floating-supply latch-up.
The dedicated JTAG pins TMS, TDI, TDO, and TCK reside in Bank 1 and follow the VCCIO1 voltage setting. According to the Altera MAX V datasheet, these pins do NOT support PCI or 1.2 V LVCMOS standards. If your JTAG host operates at 3.3 V, set VCCIO1 to 3.3 V; if your boundary-scan chain mixes 1.8 V and 3.3 V, add a level translator on the JTAG lines. Always provide pull-ups on TMS and TDI per IEEE 1149.1 to keep the TAP controller in a known state during power-up.
The TQFP-100 package at 16 x 16 mm with 0.5 mm pin pitch requires careful PCB layout. Use 0.2 mm (8 mil) traces between fine-pitch pins and at least 8 mil clearance to adjacent traces. Provide a continuous ground plane on an inner layer beneath the device to control return paths for high-speed I/O edges. For designs switching >50 MHz outputs, place 33 ohm series-termination resistors within 200 mils of the CPLD output pin to dampen transmission-line reflections on longer PCB traces.
The TQFP-100 package has a junction-to-ambient thermal resistance (theta_JA) of approximately 35 to 45 C/W on a standard 4-layer JEDEC test board. Estimated: at full 440-LE utilization toggling at 100 MHz with 74 I/Os driving 10 pF loads, internal dissipation is roughly 100 to 200 mW, producing a junction temperature rise of 5 to 10 C above ambient - well within the 0C to +85C commercial range. For industrial temperature grade, choose the I5N or I7N variant instead of the C5 commercial grade.
Informasi Konformitas
RoHS compliance verified per Intel/Altera MAX V product page. Not AEC-Q100 qualified - this is a commercial-grade CPLD. For industrial temperature grade choose the I5N/I7N variant; for AEC-Q100 automotive-grade consider MAX 10 family.
